diff options
-rw-r--r-- | Documentation/devicetree/bindings/staging/imx-drm/fsl-imx-drm.txt | 48 | ||||
-rw-r--r-- | Documentation/devicetree/bindings/staging/imx-drm/ldb.txt | 20 |
2 files changed, 59 insertions, 9 deletions
diff --git a/Documentation/devicetree/bindings/staging/imx-drm/fsl-imx-drm.txt b/Documentation/devicetree/bindings/staging/imx-drm/fsl-imx-drm.txt index b876d49..3be5ce7 100644 --- a/Documentation/devicetree/bindings/staging/imx-drm/fsl-imx-drm.txt +++ b/Documentation/devicetree/bindings/staging/imx-drm/fsl-imx-drm.txt @@ -1,3 +1,22 @@ +Freescale i.MX DRM master device +================================ + +The freescale i.MX DRM master device is a virtual device needed to list all +IPU or other display interface nodes that comprise the graphics subsystem. + +Required properties: +- compatible: Should be "fsl,imx-display-subsystem" +- ports: Should contain a list of phandles pointing to display interface ports + of IPU devices + +example: + +display-subsystem { + compatible = "fsl,display-subsystem"; + ports = <&ipu_di0>; +}; + + Freescale i.MX IPUv3 ==================== @@ -7,18 +26,31 @@ Required properties: datasheet - interrupts: Should contain sync interrupt and error interrupt, in this order. -- #crtc-cells: 1, See below - resets: phandle pointing to the system reset controller and reset line index, see reset/fsl,imx-src.txt for details +Optional properties: +- port@[0-3]: Port nodes with endpoint definitions as defined in + Documentation/devicetree/bindings/media/video-interfaces.txt. + Ports 0 and 1 should correspond to CSI0 and CSI1, + ports 2 and 3 should correspond to DI0 and DI1, respectively. example: ipu: ipu@18000000 { - #crtc-cells = <1>; + #address-cells = <1>; + #size-cells = <0>; compatible = "fsl,imx53-ipu"; reg = <0x18000000 0x080000000>; interrupts = <11 10>; resets = <&src 2>; + + ipu_di0: port@2 { + reg = <2>; + + ipu_di0_disp0: endpoint { + remote-endpoint = <&display_in>; + }; + }; }; Parallel display support @@ -26,19 +58,25 @@ Parallel display support Required properties: - compatible: Should be "fsl,imx-parallel-display" -- crtc: the crtc this display is connected to, see below Optional properties: - interface_pix_fmt: How this display is connected to the - crtc. Currently supported types: "rgb24", "rgb565", "bgr666" + display interface. Currently supported types: "rgb24", "rgb565", "bgr666" - edid: verbatim EDID data block describing attached display. - ddc: phandle describing the i2c bus handling the display data channel +- port: A port node with endpoint definitions as defined in + Documentation/devicetree/bindings/media/video-interfaces.txt. example: display@di0 { compatible = "fsl,imx-parallel-display"; edid = [edid-data]; - crtc = <&ipu 0>; interface-pix-fmt = "rgb24"; + + port { + display_in: endpoint { + remote-endpoint = <&ipu_di0_disp0>; + }; + }; }; diff --git a/Documentation/devicetree/bindings/staging/imx-drm/ldb.txt b/Documentation/devicetree/bindings/staging/imx-drm/ldb.txt index ed93778..578a1fc 100644 --- a/Documentation/devicetree/bindings/staging/imx-drm/ldb.txt +++ b/Documentation/devicetree/bindings/staging/imx-drm/ldb.txt @@ -50,12 +50,14 @@ have a look at Documentation/devicetree/bindings/video/display-timing.txt. Required properties: - reg : should be <0> or <1> - - crtcs : a list of phandles with index pointing to the IPU display interfaces - that can be used as video source for this channel. - fsl,data-mapping : should be "spwg" or "jeida" This describes how the color bits are laid out in the serialized LVDS signal. - fsl,data-width : should be <18> or <24> + - port: A port node with endpoint definitions as defined in + Documentation/devicetree/bindings/media/video-interfaces.txt. + On i.MX6, there should be four ports (port@[0-3]) that correspond + to the four LVDS multiplexer inputs. example: @@ -77,23 +79,33 @@ ldb: ldb@53fa8008 { lvds-channel@0 { reg = <0>; - crtcs = <&ipu 0>; fsl,data-mapping = "spwg"; fsl,data-width = <24>; display-timings { /* ... */ }; + + port { + lvds0_in: endpoint { + remote-endpoint = <&ipu_di0_lvds0>; + }; + }; }; lvds-channel@1 { reg = <1>; - crtcs = <&ipu 1>; fsl,data-mapping = "spwg"; fsl,data-width = <24>; display-timings { /* ... */ }; + + port { + lvds1_in: endpoint { + remote-endpoint = <&ipu_di1_lvds1>; + }; + }; }; }; |