diff options
-rw-r--r-- | Documentation/devicetree/bindings/regulator/pbias-regulator.txt | 7 | ||||
-rw-r--r-- | arch/arm/boot/dts/am57xx-beagle-x15.dts | 42 | ||||
-rw-r--r-- | arch/arm/boot/dts/dra7.dtsi | 1 | ||||
-rw-r--r-- | arch/arm/boot/dts/omap2430.dtsi | 1 | ||||
-rw-r--r-- | arch/arm/boot/dts/omap3.dtsi | 25 | ||||
-rw-r--r-- | arch/arm/boot/dts/omap4.dtsi | 1 | ||||
-rw-r--r-- | arch/arm/boot/dts/omap5-uevm.dts | 4 | ||||
-rw-r--r-- | arch/arm/boot/dts/omap5.dtsi | 1 | ||||
-rw-r--r-- | arch/arm/configs/omap2plus_defconfig | 3 | ||||
-rw-r--r-- | arch/arm/mach-omap2/id.c | 8 | ||||
-rw-r--r-- | arch/arm/mach-omap2/io.c | 1 | ||||
-rw-r--r-- | arch/arm/mach-omap2/omap_device.c | 3 | ||||
-rw-r--r-- | arch/arm/mach-omap2/soc.h | 2 | ||||
-rw-r--r-- | arch/arm/mach-omap2/timer.c | 8 | ||||
-rw-r--r-- | arch/arm/mach-omap2/vc.c | 2 | ||||
-rw-r--r-- | drivers/regulator/pbias-regulator.c | 56 |
16 files changed, 119 insertions, 46 deletions
diff --git a/Documentation/devicetree/bindings/regulator/pbias-regulator.txt b/Documentation/devicetree/bindings/regulator/pbias-regulator.txt index 32aa26f..acbcb45 100644 --- a/Documentation/devicetree/bindings/regulator/pbias-regulator.txt +++ b/Documentation/devicetree/bindings/regulator/pbias-regulator.txt @@ -2,7 +2,12 @@ PBIAS internal regulator for SD card dual voltage i/o pads on OMAP SoCs. Required properties: - compatible: - - "ti,pbias-omap" for OMAP2, OMAP3, OMAP4, OMAP5, DRA7. + - should be "ti,pbias-dra7" for DRA7 + - should be "ti,pbias-omap2" for OMAP2 + - should be "ti,pbias-omap3" for OMAP3 + - should be "ti,pbias-omap4" for OMAP4 + - should be "ti,pbias-omap5" for OMAP5 + - "ti,pbias-omap" is deprecated - reg: pbias register offset from syscon base and size of pbias register. - syscon : phandle of the system control module - regulator-name : should be diff --git a/arch/arm/boot/dts/am57xx-beagle-x15.dts b/arch/arm/boot/dts/am57xx-beagle-x15.dts index a4274ab..568adf5 100644 --- a/arch/arm/boot/dts/am57xx-beagle-x15.dts +++ b/arch/arm/boot/dts/am57xx-beagle-x15.dts @@ -98,13 +98,6 @@ pinctrl-0 = <&extcon_usb1_pins>; }; - extcon_usb2: extcon_usb2 { - compatible = "linux,extcon-usb-gpio"; - id-gpio = <&gpio7 24 GPIO_ACTIVE_HIGH>; - pinctrl-names = "default"; - pinctrl-0 = <&extcon_usb2_pins>; - }; - hdmi0: connector { compatible = "hdmi-connector"; label = "hdmi"; @@ -326,12 +319,6 @@ >; }; - extcon_usb2_pins: extcon_usb2_pins { - pinctrl-single,pins = < - 0x3e8 (PIN_INPUT_PULLUP | MUX_MODE14) /* uart1_ctsn.gpio7_24 */ - >; - }; - tpd12s015_pins: pinmux_tpd12s015_pins { pinctrl-single,pins = < 0x3b0 (PIN_OUTPUT | MUX_MODE14) /* gpio7_10 CT_CP_HPD */ @@ -432,7 +419,7 @@ }; ldo3_reg: ldo3 { - /* VDDA_1V8_PHY */ + /* VDDA_1V8_PHYA */ regulator-name = "ldo3"; regulator-min-microvolt = <1800000>; regulator-max-microvolt = <1800000>; @@ -440,6 +427,15 @@ regulator-boot-on; }; + ldo4_reg: ldo4 { + /* VDDA_1V8_PHYB */ + regulator-name = "ldo4"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-always-on; + regulator-boot-on; + }; + ldo9_reg: ldo9 { /* VDD_RTC */ regulator-name = "ldo9"; @@ -495,6 +491,14 @@ gpio-controller; #gpio-cells = <2>; }; + + extcon_usb2: tps659038_usb { + compatible = "ti,palmas-usb-vid"; + ti,enable-vbus-detection; + ti,enable-id-detection; + id-gpios = <&gpio7 24 GPIO_ACTIVE_HIGH>; + }; + }; tmp102: tmp102@48 { @@ -623,6 +627,14 @@ }; &usb2 { + /* + * Stand alone usage is peripheral only. + * However, with some resistor modifications + * this port can be used via expansion connectors + * as "host" or "dual-role". If so, provide + * the necessary dr_mode override in the expansion + * board's DT. + */ dr_mode = "peripheral"; }; @@ -681,7 +693,7 @@ &hdmi { status = "ok"; - vdda-supply = <&ldo3_reg>; + vdda-supply = <&ldo4_reg>; pinctrl-names = "default"; pinctrl-0 = <&hdmi_pins>; diff --git a/arch/arm/boot/dts/dra7.dtsi b/arch/arm/boot/dts/dra7.dtsi index fed95a4..e289c70 100644 --- a/arch/arm/boot/dts/dra7.dtsi +++ b/arch/arm/boot/dts/dra7.dtsi @@ -120,6 +120,7 @@ reg = <0x0 0x1400>; #address-cells = <1>; #size-cells = <1>; + ranges = <0 0x0 0x1400>; pbias_regulator: pbias_regulator { compatible = "ti,pbias-dra7", "ti,pbias-omap"; diff --git a/arch/arm/boot/dts/omap2430.dtsi b/arch/arm/boot/dts/omap2430.dtsi index 3961a6f..798dda0 100644 --- a/arch/arm/boot/dts/omap2430.dtsi +++ b/arch/arm/boot/dts/omap2430.dtsi @@ -56,6 +56,7 @@ reg = <0x270 0x240>; #address-cells = <1>; #size-cells = <1>; + ranges = <0 0x270 0x240>; scm_clocks: clocks { #address-cells = <1>; diff --git a/arch/arm/boot/dts/omap3.dtsi b/arch/arm/boot/dts/omap3.dtsi index 9af9ae1..8a2b253 100644 --- a/arch/arm/boot/dts/omap3.dtsi +++ b/arch/arm/boot/dts/omap3.dtsi @@ -113,10 +113,22 @@ }; scm_conf: scm_conf@270 { - compatible = "syscon"; + compatible = "syscon", "simple-bus"; reg = <0x270 0x330>; #address-cells = <1>; #size-cells = <1>; + ranges = <0 0x270 0x330>; + + pbias_regulator: pbias_regulator { + compatible = "ti,pbias-omap3", "ti,pbias-omap"; + reg = <0x2b0 0x4>; + syscon = <&scm_conf>; + pbias_mmc_reg: pbias_mmc_omap2430 { + regulator-name = "pbias_mmc_omap2430"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <3000000>; + }; + }; scm_clocks: clocks { #address-cells = <1>; @@ -202,17 +214,6 @@ dma-requests = <96>; }; - pbias_regulator: pbias_regulator { - compatible = "ti,pbias-omap3", "ti,pbias-omap"; - reg = <0x2b0 0x4>; - syscon = <&scm_conf>; - pbias_mmc_reg: pbias_mmc_omap2430 { - regulator-name = "pbias_mmc_omap2430"; - regulator-min-microvolt = <1800000>; - regulator-max-microvolt = <3000000>; - }; - }; - gpio1: gpio@48310000 { compatible = "ti,omap3-gpio"; reg = <0x48310000 0x200>; diff --git a/arch/arm/boot/dts/omap4.dtsi b/arch/arm/boot/dts/omap4.dtsi index 5aad7f3..5a206c1 100644 --- a/arch/arm/boot/dts/omap4.dtsi +++ b/arch/arm/boot/dts/omap4.dtsi @@ -196,6 +196,7 @@ reg = <0x5a0 0x170>; #address-cells = <1>; #size-cells = <1>; + ranges = <0 0x5a0 0x170>; pbias_regulator: pbias_regulator { compatible = "ti,pbias-omap4", "ti,pbias-omap"; diff --git a/arch/arm/boot/dts/omap5-uevm.dts b/arch/arm/boot/dts/omap5-uevm.dts index 3cc8f35..3cb030f 100644 --- a/arch/arm/boot/dts/omap5-uevm.dts +++ b/arch/arm/boot/dts/omap5-uevm.dts @@ -174,8 +174,8 @@ i2c5_pins: pinmux_i2c5_pins { pinctrl-single,pins = < - 0x184 (PIN_INPUT | MUX_MODE0) /* i2c5_scl */ - 0x186 (PIN_INPUT | MUX_MODE0) /* i2c5_sda */ + 0x186 (PIN_INPUT | MUX_MODE0) /* i2c5_scl */ + 0x188 (PIN_INPUT | MUX_MODE0) /* i2c5_sda */ >; }; diff --git a/arch/arm/boot/dts/omap5.dtsi b/arch/arm/boot/dts/omap5.dtsi index 8d5f9d2..4c04389 100644 --- a/arch/arm/boot/dts/omap5.dtsi +++ b/arch/arm/boot/dts/omap5.dtsi @@ -185,6 +185,7 @@ reg = <0x5a0 0xec>; #address-cells = <1>; #size-cells = <1>; + ranges = <0 0x5a0 0xec>; pbias_regulator: pbias_regulator { compatible = "ti,pbias-omap5", "ti,pbias-omap"; diff --git a/arch/arm/configs/omap2plus_defconfig b/arch/arm/configs/omap2plus_defconfig index 1860f51..3f15a5c 100644 --- a/arch/arm/configs/omap2plus_defconfig +++ b/arch/arm/configs/omap2plus_defconfig @@ -240,6 +240,7 @@ CONFIG_SSI_PROTOCOL=m CONFIG_PINCTRL_SINGLE=y CONFIG_DEBUG_GPIO=y CONFIG_GPIO_SYSFS=y +CONFIG_GPIO_PCA953X=m CONFIG_GPIO_PCF857X=y CONFIG_GPIO_TWL4030=y CONFIG_GPIO_PALMAS=y @@ -350,6 +351,8 @@ CONFIG_USB_MUSB_HDRC=m CONFIG_USB_MUSB_OMAP2PLUS=m CONFIG_USB_MUSB_AM35X=m CONFIG_USB_MUSB_DSPS=m +CONFIG_USB_INVENTRA_DMA=y +CONFIG_USB_TI_CPPI41_DMA=y CONFIG_USB_DWC3=m CONFIG_USB_TEST=m CONFIG_AM335X_PHY_USB=y diff --git a/arch/arm/mach-omap2/id.c b/arch/arm/mach-omap2/id.c index e3f713f..54a5ba5 100644 --- a/arch/arm/mach-omap2/id.c +++ b/arch/arm/mach-omap2/id.c @@ -653,8 +653,12 @@ void __init dra7xxx_check_revision(void) omap_revision = DRA752_REV_ES1_0; break; case 1: - default: omap_revision = DRA752_REV_ES1_1; + break; + case 2: + default: + omap_revision = DRA752_REV_ES2_0; + break; } break; @@ -674,7 +678,7 @@ void __init dra7xxx_check_revision(void) /* Unknown default to latest silicon rev as default*/ pr_warn("%s: unknown idcode=0x%08x (hawkeye=0x%08x,rev=0x%x)\n", __func__, idcode, hawkeye, rev); - omap_revision = DRA752_REV_ES1_1; + omap_revision = DRA752_REV_ES2_0; } sprintf(soc_name, "DRA%03x", omap_rev() >> 16); diff --git a/arch/arm/mach-omap2/io.c b/arch/arm/mach-omap2/io.c index 980c937..3eaeaca 100644 --- a/arch/arm/mach-omap2/io.c +++ b/arch/arm/mach-omap2/io.c @@ -676,6 +676,7 @@ void __init am43xx_init_early(void) void __init am43xx_init_late(void) { omap_common_late_init(); + omap2_clk_enable_autoidle_all(); } #endif diff --git a/arch/arm/mach-omap2/omap_device.c b/arch/arm/mach-omap2/omap_device.c index 4cb8fd9..72ebc4c 100644 --- a/arch/arm/mach-omap2/omap_device.c +++ b/arch/arm/mach-omap2/omap_device.c @@ -901,7 +901,8 @@ static int __init omap_device_late_idle(struct device *dev, void *data) if (od->hwmods[i]->flags & HWMOD_INIT_NO_IDLE) return 0; - if (od->_driver_status != BUS_NOTIFY_BOUND_DRIVER) { + if (od->_driver_status != BUS_NOTIFY_BOUND_DRIVER && + od->_driver_status != BUS_NOTIFY_BIND_DRIVER) { if (od->_state == OMAP_DEVICE_STATE_ENABLED) { dev_warn(dev, "%s: enabled but no driver. Idling\n", __func__); diff --git a/arch/arm/mach-omap2/soc.h b/arch/arm/mach-omap2/soc.h index f97654d..2d1d384 100644 --- a/arch/arm/mach-omap2/soc.h +++ b/arch/arm/mach-omap2/soc.h @@ -469,6 +469,8 @@ IS_OMAP_TYPE(3430, 0x3430) #define DRA7XX_CLASS 0x07000000 #define DRA752_REV_ES1_0 (DRA7XX_CLASS | (0x52 << 16) | (0x10 << 8)) #define DRA752_REV_ES1_1 (DRA7XX_CLASS | (0x52 << 16) | (0x11 << 8)) +#define DRA752_REV_ES2_0 (DRA7XX_CLASS | (0x52 << 16) | (0x20 << 8)) +#define DRA722_REV_ES1_0 (DRA7XX_CLASS | (0x22 << 16) | (0x10 << 8)) #define DRA722_REV_ES1_0 (DRA7XX_CLASS | (0x22 << 16) | (0x10 << 8)) void omap2xxx_check_revision(void); diff --git a/arch/arm/mach-omap2/timer.c b/arch/arm/mach-omap2/timer.c index e4d8701..a556551 100644 --- a/arch/arm/mach-omap2/timer.c +++ b/arch/arm/mach-omap2/timer.c @@ -297,12 +297,8 @@ static int __init omap_dm_timer_init_one(struct omap_dm_timer *timer, if (IS_ERR(src)) return PTR_ERR(src); - r = clk_set_parent(timer->fclk, src); - if (r < 0) { - pr_warn("%s: %s cannot set source\n", __func__, oh->name); - clk_put(src); - return r; - } + WARN(clk_set_parent(timer->fclk, src) < 0, + "Cannot set timer parent clock, no PLL clock driver?"); clk_put(src); diff --git a/arch/arm/mach-omap2/vc.c b/arch/arm/mach-omap2/vc.c index e5a35f6..d44d311 100644 --- a/arch/arm/mach-omap2/vc.c +++ b/arch/arm/mach-omap2/vc.c @@ -300,7 +300,7 @@ static void __init omap3_vc_init_pmic_signaling(struct voltagedomain *voltdm) val = voltdm->read(OMAP3_PRM_POLCTRL_OFFSET); if (!(val & OMAP3430_PRM_POLCTRL_CLKREQ_POL) || - (val & OMAP3430_PRM_POLCTRL_CLKREQ_POL)) { + (val & OMAP3430_PRM_POLCTRL_OFFMODE_POL)) { val |= OMAP3430_PRM_POLCTRL_CLKREQ_POL; val &= ~OMAP3430_PRM_POLCTRL_OFFMODE_POL; pr_debug("PM: fixing sys_clkreq and sys_off_mode polarity to 0x%x\n", diff --git a/drivers/regulator/pbias-regulator.c b/drivers/regulator/pbias-regulator.c index 4fa7bca..f9d74d6 100644 --- a/drivers/regulator/pbias-regulator.c +++ b/drivers/regulator/pbias-regulator.c @@ -45,6 +45,10 @@ struct pbias_regulator_data { int voltage; }; +struct pbias_of_data { + unsigned int offset; +}; + static const unsigned int pbias_volt_table[] = { 1800000, 3000000 @@ -102,8 +106,35 @@ static struct of_regulator_match pbias_matches[] = { }; #define PBIAS_NUM_REGS ARRAY_SIZE(pbias_matches) +/* Offset from SCM general area (and syscon) base */ + +static const struct pbias_of_data pbias_of_data_omap2 = { + .offset = 0x230, +}; + +static const struct pbias_of_data pbias_of_data_omap3 = { + .offset = 0x2b0, +}; + +static const struct pbias_of_data pbias_of_data_omap4 = { + .offset = 0x60, +}; + +static const struct pbias_of_data pbias_of_data_omap5 = { + .offset = 0x60, +}; + +static const struct pbias_of_data pbias_of_data_dra7 = { + .offset = 0xe00, +}; + static const struct of_device_id pbias_of_match[] = { { .compatible = "ti,pbias-omap", }, + { .compatible = "ti,pbias-omap2", .data = &pbias_of_data_omap2, }, + { .compatible = "ti,pbias-omap3", .data = &pbias_of_data_omap3, }, + { .compatible = "ti,pbias-omap4", .data = &pbias_of_data_omap4, }, + { .compatible = "ti,pbias-omap5", .data = &pbias_of_data_omap5, }, + { .compatible = "ti,pbias-dra7", .data = &pbias_of_data_dra7, }, {}, }; MODULE_DEVICE_TABLE(of, pbias_of_match); @@ -118,6 +149,9 @@ static int pbias_regulator_probe(struct platform_device *pdev) const struct pbias_reg_info *info; int ret = 0; int count, idx, data_idx = 0; + const struct of_device_id *match; + const struct pbias_of_data *data; + unsigned int offset; count = of_regulator_match(&pdev->dev, np, pbias_matches, PBIAS_NUM_REGS); @@ -133,6 +167,20 @@ static int pbias_regulator_probe(struct platform_device *pdev) if (IS_ERR(syscon)) return PTR_ERR(syscon); + match = of_match_device(of_match_ptr(pbias_of_match), &pdev->dev); + if (match && match->data) { + data = match->data; + offset = data->offset; + } else { + res = platform_get_resource(pdev, IORESOURCE_MEM, 0); + if (!res) + return -EINVAL; + + offset = res->start; + dev_WARN(&pdev->dev, + "using legacy dt data for pbias offset\n"); + } + cfg.regmap = syscon; cfg.dev = &pdev->dev; @@ -145,10 +193,6 @@ static int pbias_regulator_probe(struct platform_device *pdev) if (!info) return -ENODEV; - res = platform_get_resource(pdev, IORESOURCE_MEM, 0); - if (!res) - return -EINVAL; - drvdata[data_idx].syscon = syscon; drvdata[data_idx].info = info; drvdata[data_idx].desc.name = info->name; @@ -158,9 +202,9 @@ static int pbias_regulator_probe(struct platform_device *pdev) drvdata[data_idx].desc.volt_table = pbias_volt_table; drvdata[data_idx].desc.n_voltages = 2; drvdata[data_idx].desc.enable_time = info->enable_time; - drvdata[data_idx].desc.vsel_reg = res->start; + drvdata[data_idx].desc.vsel_reg = offset; drvdata[data_idx].desc.vsel_mask = info->vmode; - drvdata[data_idx].desc.enable_reg = res->start; + drvdata[data_idx].desc.enable_reg = offset; drvdata[data_idx].desc.enable_mask = info->enable_mask; drvdata[data_idx].desc.enable_val = info->enable; drvdata[data_idx].desc.disable_val = info->disable_val; |