diff options
Diffstat (limited to 'Documentation/devicetree/bindings/gpio')
8 files changed, 219 insertions, 5 deletions
diff --git a/Documentation/devicetree/bindings/gpio/gpio-omap.txt b/Documentation/devicetree/bindings/gpio/gpio-omap.txt new file mode 100644 index 0000000..bff51a2 --- /dev/null +++ b/Documentation/devicetree/bindings/gpio/gpio-omap.txt @@ -0,0 +1,36 @@ +OMAP GPIO controller bindings + +Required properties: +- compatible: + - "ti,omap2-gpio" for OMAP2 controllers + - "ti,omap3-gpio" for OMAP3 controllers + - "ti,omap4-gpio" for OMAP4 controllers +- #gpio-cells : Should be two. + - first cell is the pin number + - second cell is used to specify optional parameters (unused) +- gpio-controller : Marks the device node as a GPIO controller. +- #interrupt-cells : Should be 2. +- interrupt-controller: Mark the device node as an interrupt controller + The first cell is the GPIO number. + The second cell is used to specify flags: + bits[3:0] trigger type and level flags: + 1 = low-to-high edge triggered. + 2 = high-to-low edge triggered. + 4 = active high level-sensitive. + 8 = active low level-sensitive. + +OMAP specific properties: +- ti,hwmods: Name of the hwmod associated to the GPIO: + "gpio<X>", <X> being the 1-based instance number from the HW spec + + +Example: + +gpio4: gpio4 { + compatible = "ti,omap4-gpio"; + ti,hwmods = "gpio4"; + #gpio-cells = <2>; + gpio-controller; + #interrupt-cells = <2>; + interrupt-controller; +}; diff --git a/Documentation/devicetree/bindings/gpio/gpio-twl4030.txt b/Documentation/devicetree/bindings/gpio/gpio-twl4030.txt new file mode 100644 index 0000000..16695d9 --- /dev/null +++ b/Documentation/devicetree/bindings/gpio/gpio-twl4030.txt @@ -0,0 +1,23 @@ +twl4030 GPIO controller bindings + +Required properties: +- compatible: + - "ti,twl4030-gpio" for twl4030 GPIO controller +- #gpio-cells : Should be two. + - first cell is the pin number + - second cell is used to specify optional parameters (unused) +- gpio-controller : Marks the device node as a GPIO controller. +- #interrupt-cells : Should be 2. +- interrupt-controller: Mark the device node as an interrupt controller + The first cell is the GPIO number. + The second cell is not used. + +Example: + +twl_gpio: gpio { + compatible = "ti,twl4030-gpio"; + #gpio-cells = <2>; + gpio-controller; + #interrupt-cells = <2>; + interrupt-controller; +}; diff --git a/Documentation/devicetree/bindings/gpio/gpio_atmel.txt b/Documentation/devicetree/bindings/gpio/gpio_atmel.txt new file mode 100644 index 0000000..66efc80 --- /dev/null +++ b/Documentation/devicetree/bindings/gpio/gpio_atmel.txt @@ -0,0 +1,20 @@ +* Atmel GPIO controller (PIO) + +Required properties: +- compatible: "atmel,<chip>-gpio", where <chip> is at91rm9200 or at91sam9x5. +- reg: Should contain GPIO controller registers location and length +- interrupts: Should be the port interrupt shared by all the pins. +- #gpio-cells: Should be two. The first cell is the pin number and + the second cell is used to specify optional parameters (currently + unused). +- gpio-controller: Marks the device node as a GPIO controller. + +Example: + pioA: gpio@fffff200 { + compatible = "atmel,at91rm9200-gpio"; + reg = <0xfffff200 0x100>; + interrupts = <2 4>; + #gpio-cells = <2>; + gpio-controller; + }; + diff --git a/Documentation/devicetree/bindings/gpio/gpio_i2c.txt b/Documentation/devicetree/bindings/gpio/gpio_i2c.txt new file mode 100644 index 0000000..4f8ec94 --- /dev/null +++ b/Documentation/devicetree/bindings/gpio/gpio_i2c.txt @@ -0,0 +1,32 @@ +Device-Tree bindings for i2c gpio driver + +Required properties: + - compatible = "i2c-gpio"; + - gpios: sda and scl gpio + + +Optional properties: + - i2c-gpio,sda-open-drain: sda as open drain + - i2c-gpio,scl-open-drain: scl as open drain + - i2c-gpio,scl-output-only: scl as output only + - i2c-gpio,delay-us: delay between GPIO operations (may depend on each platform) + - i2c-gpio,timeout-ms: timeout to get data + +Example nodes: + +i2c@0 { + compatible = "i2c-gpio"; + gpios = <&pioA 23 0 /* sda */ + &pioA 24 0 /* scl */ + >; + i2c-gpio,sda-open-drain; + i2c-gpio,scl-open-drain; + i2c-gpio,delay-us = <2>; /* ~100 kHz */ + #address-cells = <1>; + #size-cells = <0>; + + rv3029c2@56 { + compatible = "rv3029c2"; + reg = <0x56>; + }; +}; diff --git a/Documentation/devicetree/bindings/gpio/gpio_nvidia.txt b/Documentation/devicetree/bindings/gpio/gpio_nvidia.txt index eb4b530..023c952 100644 --- a/Documentation/devicetree/bindings/gpio/gpio_nvidia.txt +++ b/Documentation/devicetree/bindings/gpio/gpio_nvidia.txt @@ -1,8 +1,40 @@ -NVIDIA Tegra 2 GPIO controller +NVIDIA Tegra GPIO controller Required properties: -- compatible : "nvidia,tegra20-gpio" +- compatible : "nvidia,tegra<chip>-gpio" +- reg : Physical base address and length of the controller's registers. +- interrupts : The interrupt outputs from the controller. For Tegra20, + there should be 7 interrupts specified, and for Tegra30, there should + be 8 interrupts specified. - #gpio-cells : Should be two. The first cell is the pin number and the second cell is used to specify optional parameters: - bit 0 specifies polarity (0 for normal, 1 for inverted) - gpio-controller : Marks the device node as a GPIO controller. +- #interrupt-cells : Should be 2. + The first cell is the GPIO number. + The second cell is used to specify flags: + bits[3:0] trigger type and level flags: + 1 = low-to-high edge triggered. + 2 = high-to-low edge triggered. + 4 = active high level-sensitive. + 8 = active low level-sensitive. + Valid combinations are 1, 2, 3, 4, 8. +- interrupt-controller : Marks the device node as an interrupt controller. + +Example: + +gpio: gpio@6000d000 { + compatible = "nvidia,tegra20-gpio"; + reg = < 0x6000d000 0x1000 >; + interrupts = < 0 32 0x04 + 0 33 0x04 + 0 34 0x04 + 0 35 0x04 + 0 55 0x04 + 0 87 0x04 + 0 89 0x04 >; + #gpio-cells = <2>; + gpio-controller; + #interrupt-cells = <2>; + interrupt-controller; +}; diff --git a/Documentation/devicetree/bindings/gpio/led.txt b/Documentation/devicetree/bindings/gpio/led.txt index 141087c..fd2bd56 100644 --- a/Documentation/devicetree/bindings/gpio/led.txt +++ b/Documentation/devicetree/bindings/gpio/led.txt @@ -7,9 +7,9 @@ Each LED is represented as a sub-node of the gpio-leds device. Each node's name represents the name of the corresponding LED. LED sub-node properties: -- gpios : Should specify the LED's GPIO, see "Specifying GPIO information - for devices" in Documentation/devicetree/booting-without-of.txt. Active - low LEDs should be indicated using flags in the GPIO specifier. +- gpios : Should specify the LED's GPIO, see "gpios property" in + Documentation/devicetree/gpio.txt. Active low LEDs should be + indicated using flags in the GPIO specifier. - label : (optional) The label for this LED. If omitted, the label is taken from the node name (excluding the unit address). - linux,default-trigger : (optional) This parameter, if present, is a diff --git a/Documentation/devicetree/bindings/gpio/mrvl-gpio.txt b/Documentation/devicetree/bindings/gpio/mrvl-gpio.txt new file mode 100644 index 0000000..1e34cfe --- /dev/null +++ b/Documentation/devicetree/bindings/gpio/mrvl-gpio.txt @@ -0,0 +1,23 @@ +* Marvell PXA GPIO controller + +Required properties: +- compatible : Should be "mrvl,pxa-gpio" or "mrvl,mmp-gpio" +- reg : Address and length of the register set for the device +- interrupts : Should be the port interrupt shared by all gpio pins, if +- interrupt-name : Should be the name of irq resource. + one number. +- gpio-controller : Marks the device node as a gpio controller. +- #gpio-cells : Should be one. It is the pin number. + +Example: + + gpio: gpio@d4019000 { + compatible = "mrvl,mmp-gpio", "mrvl,pxa-gpio"; + reg = <0xd4019000 0x1000>; + interrupts = <49>, <17>, <18>; + interrupt-name = "gpio_mux", "gpio0", "gpio1"; + gpio-controller; + #gpio-cells = <1>; + interrupt-controller; + #interrupt-cells = <1>; + }; diff --git a/Documentation/devicetree/bindings/gpio/sodaville.txt b/Documentation/devicetree/bindings/gpio/sodaville.txt new file mode 100644 index 0000000..563eff2 --- /dev/null +++ b/Documentation/devicetree/bindings/gpio/sodaville.txt @@ -0,0 +1,48 @@ +GPIO controller on CE4100 / Sodaville SoCs +========================================== + +The bindings for CE4100's GPIO controller match the generic description +which is covered by the gpio.txt file in this folder. + +The only additional property is the intel,muxctl property which holds the +value which is written into the MUXCNTL register. + +There is no compatible property for now because the driver is probed via +PCI id (vendor 0x8086 device 0x2e67). + +The interrupt specifier consists of two cells encoded as follows: + - <1st cell>: The interrupt-number that identifies the interrupt source. + - <2nd cell>: The level-sense information, encoded as follows: + 4 - active high level-sensitive + 8 - active low level-sensitive + +Example of the GPIO device and one user: + + pcigpio: gpio@b,1 { + /* two cells for GPIO and interrupt */ + #gpio-cells = <2>; + #interrupt-cells = <2>; + compatible = "pci8086,2e67.2", + "pci8086,2e67", + "pciclassff0000", + "pciclassff00"; + + reg = <0x15900 0x0 0x0 0x0 0x0>; + /* Interrupt line of the gpio device */ + interrupts = <15 1>; + /* It is an interrupt and GPIO controller itself */ + interrupt-controller; + gpio-controller; + intel,muxctl = <0>; + }; + + testuser@20 { + compatible = "example,testuser"; + /* User the 11th GPIO line as an active high triggered + * level interrupt + */ + interrupts = <11 8>; + interrupt-parent = <&pcigpio>; + /* Use this GPIO also with the gpio functions */ + gpios = <&pcigpio 11 0>; + }; |