diff options
Diffstat (limited to 'Documentation/devicetree/bindings/interrupt-controller')
| -rw-r--r-- | Documentation/devicetree/bindings/interrupt-controller/brcm,bcm2835-armctrl-ic.txt | 110 | ||||
| -rw-r--r-- | Documentation/devicetree/bindings/interrupt-controller/interrupts.txt | 95 |
2 files changed, 205 insertions, 0 deletions
diff --git a/Documentation/devicetree/bindings/interrupt-controller/brcm,bcm2835-armctrl-ic.txt b/Documentation/devicetree/bindings/interrupt-controller/brcm,bcm2835-armctrl-ic.txt new file mode 100644 index 0000000..7da578d --- /dev/null +++ b/Documentation/devicetree/bindings/interrupt-controller/brcm,bcm2835-armctrl-ic.txt @@ -0,0 +1,110 @@ +BCM2835 Top-Level ("ARMCTRL") Interrupt Controller + +The BCM2835 contains a custom top-level interrupt controller, which supports +72 interrupt sources using a 2-level register scheme. The interrupt +controller, or the HW block containing it, is referred to occasionally +as "armctrl" in the SoC documentation, hence naming of this binding. + +Required properties: + +- compatible : should be "brcm,bcm2835-armctrl-ic" +- reg : Specifies base physical address and size of the registers. +- interrupt-controller : Identifies the node as an interrupt controller +- #interrupt-cells : Specifies the number of cells needed to encode an + interrupt source. The value shall be 2. + + The 1st cell is the interrupt bank; 0 for interrupts in the "IRQ basic + pending" register, or 1/2 respectively for interrupts in the "IRQ pending + 1/2" register. + + The 2nd cell contains the interrupt number within the bank. Valid values + are 0..7 for bank 0, and 0..31 for bank 1. + +The interrupt sources are as follows: + +Bank 0: +0: ARM_TIMER +1: ARM_MAILBOX +2: ARM_DOORBELL_0 +3: ARM_DOORBELL_1 +4: VPU0_HALTED +5: VPU1_HALTED +6: ILLEGAL_TYPE0 +7: ILLEGAL_TYPE1 + +Bank 1: +0: TIMER0 +1: TIMER1 +2: TIMER2 +3: TIMER3 +4: CODEC0 +5: CODEC1 +6: CODEC2 +7: VC_JPEG +8: ISP +9: VC_USB +10: VC_3D +11: TRANSPOSER +12: MULTICORESYNC0 +13: MULTICORESYNC1 +14: MULTICORESYNC2 +15: MULTICORESYNC3 +16: DMA0 +17: DMA1 +18: VC_DMA2 +19: VC_DMA3 +20: DMA4 +21: DMA5 +22: DMA6 +23: DMA7 +24: DMA8 +25: DMA9 +26: DMA10 +27: DMA11 +28: DMA12 +29: AUX +30: ARM +31: VPUDMA + +Bank 2: +0: HOSTPORT +1: VIDEOSCALER +2: CCP2TX +3: SDC +4: DSI0 +5: AVE +6: CAM0 +7: CAM1 +8: HDMI0 +9: HDMI1 +10: PIXELVALVE1 +11: I2CSPISLV +12: DSI1 +13: PWA0 +14: PWA1 +15: CPR +16: SMI +17: GPIO0 +18: GPIO1 +19: GPIO2 +20: GPIO3 +21: VC_I2C +22: VC_SPI +23: VC_I2SPCM +24: VC_SDIO +25: VC_UART +26: SLIMBUS +27: VEC +28: CPG +29: RNG +30: VC_ARASANSDIO +31: AVSPMON + +Example: + +intc: interrupt-controller { + compatible = "brcm,bcm2835-armctrl-ic"; + reg = <0x7e00b200 0x200>; + interrupt-controller; + #interrupt-cells = <2>; +}; diff --git a/Documentation/devicetree/bindings/interrupt-controller/interrupts.txt b/Documentation/devicetree/bindings/interrupt-controller/interrupts.txt new file mode 100644 index 0000000..72a06c0 --- /dev/null +++ b/Documentation/devicetree/bindings/interrupt-controller/interrupts.txt @@ -0,0 +1,95 @@ +Specifying interrupt information for devices +============================================ + +1) Interrupt client nodes +------------------------- + +Nodes that describe devices which generate interrupts must contain an +"interrupts" property. This property must contain a list of interrupt +specifiers, one per output interrupt. The format of the interrupt specifier is +determined by the interrupt controller to which the interrupts are routed; see +section 2 below for details. + +The "interrupt-parent" property is used to specify the controller to which +interrupts are routed and contains a single phandle referring to the interrupt +controller node. This property is inherited, so it may be specified in an +interrupt client node or in any of its parent nodes. + +2) Interrupt controller nodes +----------------------------- + +A device is marked as an interrupt controller with the "interrupt-controller" +property. This is a empty, boolean property. An additional "#interrupt-cells" +property defines the number of cells needed to specify a single interrupt. + +It is the responsibility of the interrupt controller's binding to define the +length and format of the interrupt specifier. The following two variants are +commonly used: + + a) one cell + ----------- + The #interrupt-cells property is set to 1 and the single cell defines the + index of the interrupt within the controller. + + Example: + + vic: intc@10140000 { + compatible = "arm,versatile-vic"; + interrupt-controller; + #interrupt-cells = <1>; + reg = <0x10140000 0x1000>; + }; + + sic: intc@10003000 { + compatible = "arm,versatile-sic"; + interrupt-controller; + #interrupt-cells = <1>; + reg = <0x10003000 0x1000>; + interrupt-parent = <&vic>; + interrupts = <31>; /* Cascaded to vic */ + }; + + b) two cells + ------------ + The #interrupt-cells property is set to 2 and the first cell defines the + index of the interrupt within the controller, while the second cell is used + to specify any of the following flags: + - bits[3:0] trigger type and level flags + 1 = low-to-high edge triggered + 2 = high-to-low edge triggered + 4 = active high level-sensitive + 8 = active low level-sensitive + + Example: + + i2c@7000c000 { + gpioext: gpio-adnp@41 { + compatible = "ad,gpio-adnp"; + reg = <0x41>; + + interrupt-parent = <&gpio>; + interrupts = <160 1>; + + gpio-controller; + #gpio-cells = <1>; + + interrupt-controller; + #interrupt-cells = <2>; + + nr-gpios = <64>; + }; + + sx8634@2b { + compatible = "smtc,sx8634"; + reg = <0x2b>; + + interrupt-parent = <&gpioext>; + interrupts = <3 0x8>; + + #address-cells = <1>; + #size-cells = <0>; + + threshold = <0x40>; + sensitivity = <7>; + }; + }; |