diff options
Diffstat (limited to 'Documentation/devicetree/bindings/pci')
-rw-r--r-- | Documentation/devicetree/bindings/pci/designware-pcie.txt | 3 | ||||
-rw-r--r-- | Documentation/devicetree/bindings/pci/pci-keystone.txt | 68 |
2 files changed, 71 insertions, 0 deletions
diff --git a/Documentation/devicetree/bindings/pci/designware-pcie.txt b/Documentation/devicetree/bindings/pci/designware-pcie.txt index ed0d9b9..9f4faa8 100644 --- a/Documentation/devicetree/bindings/pci/designware-pcie.txt +++ b/Documentation/devicetree/bindings/pci/designware-pcie.txt @@ -23,3 +23,6 @@ Required properties: Optional properties: - reset-gpio: gpio pin number of power good signal +- bus-range: PCI bus numbers covered (it is recommended for new devicetrees to + specify this property, to keep backwards compatibility a range of 0x00-0xff + is assumed if not present) diff --git a/Documentation/devicetree/bindings/pci/pci-keystone.txt b/Documentation/devicetree/bindings/pci/pci-keystone.txt new file mode 100644 index 0000000..ceb3e24 --- /dev/null +++ b/Documentation/devicetree/bindings/pci/pci-keystone.txt @@ -0,0 +1,68 @@ +TI Keystone PCIe interface + +Keystone PCI host Controller is based on Designware PCI h/w version 3.65. +It shares common functions with PCIe Designware core driver and inherit +common properties defined in +Documentation/devicetree/bindings/pci/designware-pci.txt + +Please refer to Documentation/devicetree/bindings/pci/designware-pci.txt +for the details of Designware DT bindings. Additional properties are +described here as well as properties that are not applicable. + +Required Properties:- + +compatibility: "ti,keystone-pcie" +reg: index 1 is the base address and length of DW application registers. + index 2 is the base address and length of PCI mode configuration + register. + index 3 is the base address and length of PCI device ID register. + +pcie_msi_intc : Interrupt controller device node for MSI IRQ chip + interrupt-cells: should be set to 1 + interrupt-parent: Parent interrupt controller phandle + interrupts: GIC interrupt lines connected to PCI MSI interrupt lines + + Example: + pcie_msi_intc: msi-interrupt-controller { + interrupt-controller; + #interrupt-cells = <1>; + interrupt-parent = <&gic>; + interrupts = <GIC_SPI 30 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 31 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 32 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 33 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 34 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 35 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 36 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 37 IRQ_TYPE_EDGE_RISING>; + }; + +pcie_intc: Interrupt controller device node for Legacy IRQ chip + interrupt-cells: should be set to 1 + interrupt-parent: Parent interrupt controller phandle + interrupts: GIC interrupt lines connected to PCI Legacy interrupt lines + + Example: + pcie_intc: legacy-interrupt-controller { + interrupt-controller; + #interrupt-cells = <1>; + interrupt-parent = <&gic>; + interrupts = <GIC_SPI 26 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 27 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 28 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 29 IRQ_TYPE_EDGE_RISING>; + }; + +Optional properties:- + phys: phandle to Generic Keystone SerDes phy for PCI + phy-names: name of the Generic Keystine SerDes phy for PCI + - If boot loader already does PCI link establishment, then phys and + phy-names shouldn't be present. + +Designware DT Properties not applicable for Keystone PCI + +1. pcie_bus clock-names not used. Instead, a phandle to phys is used. + +Note for PCI driver usage +========================= +Driver requires pci=pcie_bus_perf in the bootargs for proper functioning. |