diff options
Diffstat (limited to 'Documentation/devicetree/bindings/sound')
5 files changed, 144 insertions, 14 deletions
diff --git a/Documentation/devicetree/bindings/sound/cs42l73.txt b/Documentation/devicetree/bindings/sound/cs42l73.txt new file mode 100644 index 0000000..80ae910 --- /dev/null +++ b/Documentation/devicetree/bindings/sound/cs42l73.txt @@ -0,0 +1,22 @@ +CS42L73 audio CODEC + +Required properties: + + - compatible : "cirrus,cs42l73" + + - reg : the I2C address of the device for I2C + +Optional properties: + + - reset_gpio : a GPIO spec for the reset pin. + - chgfreq : Charge Pump Frequency values 0x00-0x0F + + +Example: + +codec: cs42l73@4a { + compatible = "cirrus,cs42l73"; + reg = <0x4a>; + reset_gpio = <&gpio 10 0>; + chgfreq = <0x05>; +};
\ No newline at end of file diff --git a/Documentation/devicetree/bindings/sound/davinci-evm-audio.txt b/Documentation/devicetree/bindings/sound/davinci-evm-audio.txt new file mode 100644 index 0000000..865178d --- /dev/null +++ b/Documentation/devicetree/bindings/sound/davinci-evm-audio.txt @@ -0,0 +1,42 @@ +* Texas Instruments SoC audio setups with TLV320AIC3X Codec + +Required properties: +- compatible : "ti,da830-evm-audio" : forDM365/DA8xx/OMAPL1x/AM33xx +- ti,model : The user-visible name of this sound complex. +- ti,audio-codec : The phandle of the TLV320AIC3x audio codec +- ti,mcasp-controller : The phandle of the McASP controller +- ti,codec-clock-rate : The Codec Clock rate (in Hz) applied to the Codec +- ti,audio-routing : A list of the connections between audio components. + Each entry is a pair of strings, the first being the connection's sink, + the second being the connection's source. Valid names for sources and + sinks are the codec's pins, and the jacks on the board: + + Board connectors: + + * Headphone Jack + * Line Out + * Mic Jack + * Line In + + +Example: + +sound { + compatible = "ti,da830-evm-audio"; + ti,model = "DA830 EVM"; + ti,audio-codec = <&tlv320aic3x>; + ti,mcasp-controller = <&mcasp1>; + ti,codec-clock-rate = <12000000>; + ti,audio-routing = + "Headphone Jack", "HPLOUT", + "Headphone Jack", "HPROUT", + "Line Out", "LLOUT", + "Line Out", "RLOUT", + "MIC3L", "Mic Bias 2V", + "MIC3R", "Mic Bias 2V", + "Mic Bias 2V", "Mic Jack", + "LINE1L", "Line In", + "LINE2L", "Line In", + "LINE1R", "Line In", + "LINE2R", "Line In"; +}; diff --git a/Documentation/devicetree/bindings/sound/davinci-mcasp-audio.txt b/Documentation/devicetree/bindings/sound/davinci-mcasp-audio.txt index 374e145..ed785b3 100644 --- a/Documentation/devicetree/bindings/sound/davinci-mcasp-audio.txt +++ b/Documentation/devicetree/bindings/sound/davinci-mcasp-audio.txt @@ -4,17 +4,25 @@ Required properties: - compatible : "ti,dm646x-mcasp-audio" : for DM646x platforms "ti,da830-mcasp-audio" : for both DA830 & DA850 platforms - "ti,omap2-mcasp-audio" : for OMAP2 platforms (TI81xx, AM33xx) - -- reg : Should contain McASP registers offset and length -- interrupts : Interrupt number for McASP -- op-mode : I2S/DIT ops mode. -- tdm-slots : Slots for TDM operation. -- num-serializer : Serializers used by McASP. -- serial-dir : A list of serializer pin mode. The list number should be equal - to "num-serializer" parameter. Each entry is a number indication - serializer pin direction. (0 - INACTIVE, 1 - TX, 2 - RX) + "ti,am33xx-mcasp-audio" : for AM33xx platforms (AM33xx, TI81xx) +- reg : Should contain reg specifiers for the entries in the reg-names property. +- reg-names : Should contain: + * "mpu" for the main registers (required). For compatibility with + existing software, it is recommended this is the first entry. + * "dat" for separate data port register access (optional). +- op-mode : I2S/DIT ops mode. 0 for I2S mode. 1 for DIT mode used for S/PDIF, + IEC60958-1, and AES-3 formats. +- tdm-slots : Slots for TDM operation. Indicates number of channels transmitted + or received over one serializer. +- serial-dir : A list of serializer configuration. Each entry is a number + indication for serializer pin direction. + (0 - INACTIVE, 1 - TX, 2 - RX) +- dmas: two element list of DMA controller phandles and DMA request line + ordered pairs. +- dma-names: identifier string for each DMA request line in the dmas property. + These strings correspond 1:1 with the ordered pairs in dmas. The dma + identifiers must be "rx" and "tx". Optional properties: @@ -23,18 +31,23 @@ Optional properties: - rx-num-evt : FIFO levels. - sram-size-playback : size of sram to be allocated during playback - sram-size-capture : size of sram to be allocated during capture +- interrupts : Interrupt numbers for McASP, currently not used by the driver +- interrupt-names : Known interrupt names are "tx" and "rx" +- pinctrl-0: Should specify pin control group used for this controller. +- pinctrl-names: Should contain only one value - "default", for more details + please refer to pinctrl-bindings.txt + Example: mcasp0: mcasp0@1d00000 { compatible = "ti,da830-mcasp-audio"; - #address-cells = <1>; - #size-cells = <0>; reg = <0x100000 0x3000>; - interrupts = <82 83>; + reg-names "mpu"; + interrupts = <82>, <83>; + interrupts-names = "tx", "rx"; op-mode = <0>; /* MCASP_IIS_MODE */ tdm-slots = <2>; - num-serializer = <16>; serial-dir = < 0 0 0 0 /* 0: INACTIVE, 1: TX, 2: RX */ 0 0 0 0 diff --git a/Documentation/devicetree/bindings/sound/tlv320aic3x.txt b/Documentation/devicetree/bindings/sound/tlv320aic3x.txt index 705a6b1..5e6040c 100644 --- a/Documentation/devicetree/bindings/sound/tlv320aic3x.txt +++ b/Documentation/devicetree/bindings/sound/tlv320aic3x.txt @@ -24,10 +24,36 @@ Optional properties: 3 - MICBIAS output is connected to AVDD, If this node is not mentioned or if the value is incorrect, then MicBias is powered down. +- AVDD-supply, IOVDD-supply, DRVDD-supply, DVDD-supply : power supplies for the + device as covered in Documentation/devicetree/bindings/regulator/regulator.txt + +CODEC output pins: + * LLOUT + * RLOUT + * MONO_LOUT + * HPLOUT + * HPROUT + * HPLCOM + * HPRCOM + +CODEC input pins: + * MIC3L + * MIC3R + * LINE1L + * LINE2L + * LINE1R + * LINE2R + +The pins can be used in referring sound node's audio-routing property. Example: tlv320aic3x: tlv320aic3x@1b { compatible = "ti,tlv320aic3x"; reg = <0x1b>; + + AVDD-supply = <®ulator>; + IOVDD-supply = <®ulator>; + DRVDD-supply = <®ulator>; + DVDD-supply = <®ulator>; }; diff --git a/Documentation/devicetree/bindings/sound/tpa6130a2.txt b/Documentation/devicetree/bindings/sound/tpa6130a2.txt new file mode 100644 index 0000000..6dfa740 --- /dev/null +++ b/Documentation/devicetree/bindings/sound/tpa6130a2.txt @@ -0,0 +1,27 @@ +Texas Instruments - tpa6130a2 Codec module + +The tpa6130a2 serial control bus communicates through I2C protocols + +Required properties: + +- compatible - "string" - One of: + "ti,tpa6130a2" - TPA6130A2 + "ti,tpa6140a2" - TPA6140A2 + + +- reg - <int> - I2C slave address + +- Vdd-supply - <phandle> - power supply regulator + +Optional properties: + +- power-gpio - gpio pin to power the device + +Example: + +tpa6130a2: tpa6130a2@60 { + compatible = "ti,tpa6130a2"; + reg = <0x60>; + Vdd-supply = <&vmmc2>; + power-gpio = <&gpio4 2 GPIO_ACTIVE_HIGH>; +}; |