diff options
Diffstat (limited to 'Documentation/devicetree/bindings/spi')
6 files changed, 132 insertions, 0 deletions
diff --git a/Documentation/devicetree/bindings/spi/mxs-spi.txt b/Documentation/devicetree/bindings/spi/mxs-spi.txt new file mode 100644 index 0000000..e2e1395 --- /dev/null +++ b/Documentation/devicetree/bindings/spi/mxs-spi.txt @@ -0,0 +1,22 @@ +* Freescale MX233/MX28 SSP/SPI + +Required properties: +- compatible: Should be "fsl,<soc>-spi", where soc is "imx23" or "imx28" +- reg: Offset and length of the register set for the device +- interrupts: Should contain SSP interrupts (error irq first, dma irq second) +- fsl,ssp-dma-channel: APBX DMA channel for the SSP + +Optional properties: +- clock-frequency : Input clock frequency to the SPI block in Hz. + Default is 160000000 Hz. + +Example: + +ssp0: ssp@80010000 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "fsl,imx28-spi"; + reg = <0x80010000 0x2000>; + interrupts = <96 82>; + fsl,ssp-dma-channel = <0>; +}; diff --git a/Documentation/devicetree/bindings/spi/spi-bus.txt b/Documentation/devicetree/bindings/spi/spi-bus.txt index e782add..d2c33d0 100644 --- a/Documentation/devicetree/bindings/spi/spi-bus.txt +++ b/Documentation/devicetree/bindings/spi/spi-bus.txt @@ -21,6 +21,9 @@ assumption that board specific platform code will be used to manage chip selects. Individual drivers can define additional properties to support describing the chip select layout. +Optional property: +- num-cs : total number of chipselects + SPI slave nodes must be children of the SPI master node and can contain the following properties. - reg - (required) chip select address of device. diff --git a/Documentation/devicetree/bindings/spi/spi-gpio.txt b/Documentation/devicetree/bindings/spi/spi-gpio.txt new file mode 100644 index 0000000..8a824be --- /dev/null +++ b/Documentation/devicetree/bindings/spi/spi-gpio.txt @@ -0,0 +1,29 @@ +SPI-GPIO devicetree bindings + +Required properties: + + - compatible: should be set to "spi-gpio" + - #address-cells: should be set to <0x1> + - ranges + - gpio-sck: GPIO spec for the SCK line to use + - gpio-miso: GPIO spec for the MISO line to use + - gpio-mosi: GPIO spec for the MOSI line to use + - cs-gpios: GPIOs to use for chipselect lines + - num-chipselects: number of chipselect lines + +Example: + + spi { + compatible = "spi-gpio"; + #address-cells = <0x1>; + ranges; + + gpio-sck = <&gpio 95 0>; + gpio-miso = <&gpio 98 0>; + gpio-mosi = <&gpio 97 0>; + cs-gpios = <&gpio 125 0>; + num-chipselects = <1>; + + /* clients */ + }; + diff --git a/Documentation/devicetree/bindings/spi/spi-octeon.txt b/Documentation/devicetree/bindings/spi/spi-octeon.txt new file mode 100644 index 0000000..431add1 --- /dev/null +++ b/Documentation/devicetree/bindings/spi/spi-octeon.txt @@ -0,0 +1,33 @@ +Cavium, Inc. OCTEON SOC SPI master controller. + +Required properties: +- compatible : "cavium,octeon-3010-spi" +- reg : The register base for the controller. +- interrupts : One interrupt, used by the controller. +- #address-cells : <1>, as required by generic SPI binding. +- #size-cells : <0>, also as required by generic SPI binding. + +Child nodes as per the generic SPI binding. + +Example: + + spi@1070000001000 { + compatible = "cavium,octeon-3010-spi"; + reg = <0x10700 0x00001000 0x0 0x100>; + interrupts = <0 58>; + #address-cells = <1>; + #size-cells = <0>; + + eeprom@0 { + compatible = "st,m95256", "atmel,at25"; + reg = <0>; + spi-max-frequency = <5000000>; + spi-cpha; + spi-cpol; + + pagesize = <64>; + size = <32768>; + address-width = <16>; + }; + }; + diff --git a/Documentation/devicetree/bindings/spi/spi-sc18is602.txt b/Documentation/devicetree/bindings/spi/spi-sc18is602.txt new file mode 100644 index 0000000..02f9033 --- /dev/null +++ b/Documentation/devicetree/bindings/spi/spi-sc18is602.txt @@ -0,0 +1,23 @@ +NXP SC18IS602/SCIS603 + +Required properties: + - compatible : Should be one of + "nxp,sc18is602" + "nxp,sc18is602b" + "nxp,sc18is603" + - reg: I2C bus address + +Optional properties: + - clock-frequency : external oscillator clock frequency. If not + specified, the SC18IS602 default frequency (7372000) will be used. + +The clock-frequency property is relevant and needed only if the chip has an +external oscillator (SC18IS603). + +Example: + + sc18is603@28 { + compatible = "nxp,sc18is603"; + reg = <0x28>; + clock-frequency = <14744000>; + } diff --git a/Documentation/devicetree/bindings/spi/spi_pl022.txt b/Documentation/devicetree/bindings/spi/spi_pl022.txt index 306ec3f..f158fd3 100644 --- a/Documentation/devicetree/bindings/spi/spi_pl022.txt +++ b/Documentation/devicetree/bindings/spi/spi_pl022.txt @@ -6,7 +6,29 @@ Required properties: - interrupts : Should contain SPI controller interrupt Optional properties: +- num-cs : total number of chipselects - cs-gpios : should specify GPIOs used for chipselects. The gpios will be referred to as reg = <index> in the SPI child nodes. If unspecified, a single SPI device without a chip select can be used. +- pl022,autosuspend-delay : delay in ms following transfer completion before + the runtime power management system suspends the + device. A setting of 0 indicates no delay and the + device will be suspended immediately +- pl022,rt : indicates the controller should run the message pump with realtime + priority to minimise the transfer latency on the bus (boolean) + + +SPI slave nodes must be children of the SPI master node and can +contain the following properties. + +- pl022,interface : interface type: + 0: SPI + 1: Texas Instruments Synchronous Serial Frame Format + 2: Microwire (Half Duplex) +- pl022,com-mode : polling, interrupt or dma +- pl022,rx-level-trig : Rx FIFO watermark level +- pl022,tx-level-trig : Tx FIFO watermark level +- pl022,ctrl-len : Microwire interface: Control length +- pl022,wait-state : Microwire interface: Wait state +- pl022,duplex : Microwire interface: Full/Half duplex |