summaryrefslogtreecommitdiff
path: root/Documentation/devicetree/bindings/usb/omap-usb.txt
diff options
context:
space:
mode:
Diffstat (limited to 'Documentation/devicetree/bindings/usb/omap-usb.txt')
-rw-r--r--Documentation/devicetree/bindings/usb/omap-usb.txt40
1 files changed, 34 insertions, 6 deletions
diff --git a/Documentation/devicetree/bindings/usb/omap-usb.txt b/Documentation/devicetree/bindings/usb/omap-usb.txt
index 1ef0ce7..662f0f1 100644
--- a/Documentation/devicetree/bindings/usb/omap-usb.txt
+++ b/Documentation/devicetree/bindings/usb/omap-usb.txt
@@ -8,10 +8,10 @@ OMAP MUSB GLUE
and disconnect.
- multipoint : Should be "1" indicating the musb controller supports
multipoint. This is a MUSB configuration-specific setting.
- - num_eps : Specifies the number of endpoints. This is also a
+ - num-eps : Specifies the number of endpoints. This is also a
MUSB configuration-specific setting. Should be set to "16"
- - ram_bits : Specifies the ram address size. Should be set to "12"
- - interface_type : This is a board specific setting to describe the type of
+ - ram-bits : Specifies the ram address size. Should be set to "12"
+ - interface-type : This is a board specific setting to describe the type of
interface between the controller and the phy. It should be "0" or "1"
specifying ULPI and UTMI respectively.
- mode : Should be "3" to represent OTG. "1" signifies HOST and "2"
@@ -29,18 +29,46 @@ usb_otg_hs: usb_otg_hs@4a0ab000 {
ti,hwmods = "usb_otg_hs";
ti,has-mailbox;
multipoint = <1>;
- num_eps = <16>;
- ram_bits = <12>;
+ num-eps = <16>;
+ ram-bits = <12>;
ctrl-module = <&omap_control_usb>;
};
Board specific device node entry
&usb_otg_hs {
- interface_type = <1>;
+ interface-type = <1>;
mode = <3>;
power = <50>;
};
+OMAP DWC3 GLUE
+ - compatible : Should be "ti,dwc3"
+ - ti,hwmods : Should be "usb_otg_ss"
+ - reg : Address and length of the register set for the device.
+ - interrupts : The irq number of this device that is used to interrupt the
+ MPU
+ - #address-cells, #size-cells : Must be present if the device has sub-nodes
+ - utmi-mode : controls the source of UTMI/PIPE status for VBUS and OTG ID.
+ It should be set to "1" for HW mode and "2" for SW mode.
+ - ranges: the child address space are mapped 1:1 onto the parent address space
+
+Sub-nodes:
+The dwc3 core should be added as subnode to omap dwc3 glue.
+- dwc3 :
+ The binding details of dwc3 can be found in:
+ Documentation/devicetree/bindings/usb/dwc3.txt
+
+omap_dwc3 {
+ compatible = "ti,dwc3";
+ ti,hwmods = "usb_otg_ss";
+ reg = <0x4a020000 0x1ff>;
+ interrupts = <0 93 4>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+ utmi-mode = <2>;
+ ranges;
+};
+
OMAP CONTROL USB
Required properties: