diff options
Diffstat (limited to 'Documentation/devicetree/bindings')
20 files changed, 201 insertions, 112 deletions
diff --git a/Documentation/devicetree/bindings/arc/archs-pct.txt b/Documentation/devicetree/bindings/arc/archs-pct.txt index 1ae98b87..e4b9dce 100644 --- a/Documentation/devicetree/bindings/arc/archs-pct.txt +++ b/Documentation/devicetree/bindings/arc/archs-pct.txt @@ -2,7 +2,7 @@ The ARC HS can be configured with a pipeline performance monitor for counting CPU and cache events like cache misses and hits. Like conventional PCT there -are 100+ hardware conditions dynamically mapped to upto 32 counters. +are 100+ hardware conditions dynamically mapped to up to 32 counters. It also supports overflow interrupts. Required properties: diff --git a/Documentation/devicetree/bindings/arc/pct.txt b/Documentation/devicetree/bindings/arc/pct.txt index 7b95884..4e874d9 100644 --- a/Documentation/devicetree/bindings/arc/pct.txt +++ b/Documentation/devicetree/bindings/arc/pct.txt @@ -2,7 +2,7 @@ The ARC700 can be configured with a pipeline performance monitor for counting CPU and cache events like cache misses and hits. Like conventional PCT there -are 100+ hardware conditions dynamically mapped to upto 32 counters +are 100+ hardware conditions dynamically mapped to up to 32 counters Note that: * The ARC 700 PCT does not support interrupts; although HW events may be diff --git a/Documentation/devicetree/bindings/arm/cpus.txt b/Documentation/devicetree/bindings/arm/cpus.txt index ccc62f1..3f0cbbb 100644 --- a/Documentation/devicetree/bindings/arm/cpus.txt +++ b/Documentation/devicetree/bindings/arm/cpus.txt @@ -192,7 +192,6 @@ nodes to be present and contain the properties described below. can be one of: "allwinner,sun6i-a31" "allwinner,sun8i-a23" - "arm,psci" "arm,realview-smp" "brcm,bcm-nsp-smp" "brcm,brahma-b15" diff --git a/Documentation/devicetree/bindings/ata/ahci-platform.txt b/Documentation/devicetree/bindings/ata/ahci-platform.txt index 30df832..87adfb2 100644 --- a/Documentation/devicetree/bindings/ata/ahci-platform.txt +++ b/Documentation/devicetree/bindings/ata/ahci-platform.txt @@ -32,6 +32,10 @@ Optional properties: - target-supply : regulator for SATA target power - phys : reference to the SATA PHY node - phy-names : must be "sata-phy" +- ports-implemented : Mask that indicates which ports that the HBA supports + are available for software to use. Useful if PORTS_IMPL + is not programmed by the BIOS, which is true with + some embedded SOC's. Required properties when using sub-nodes: - #address-cells : number of cells to encode an address diff --git a/Documentation/devicetree/bindings/clock/qca,ath79-pll.txt b/Documentation/devicetree/bindings/clock/qca,ath79-pll.txt index e0fc2c1..241fb05 100644 --- a/Documentation/devicetree/bindings/clock/qca,ath79-pll.txt +++ b/Documentation/devicetree/bindings/clock/qca,ath79-pll.txt @@ -3,7 +3,7 @@ Binding for Qualcomm Atheros AR7xxx/AR9XXX PLL controller The PPL controller provides the 3 main clocks of the SoC: CPU, DDR and AHB. Required Properties: -- compatible: has to be "qca,<soctype>-cpu-intc" and one of the following +- compatible: has to be "qca,<soctype>-pll" and one of the following fallbacks: - "qca,ar7100-pll" - "qca,ar7240-pll" @@ -21,8 +21,8 @@ Optional properties: Example: - memory-controller@18050000 { - compatible = "qca,ar9132-ppl", "qca,ar9130-pll"; + pll-controller@18050000 { + compatible = "qca,ar9132-pll", "qca,ar9130-pll"; reg = <0x18050000 0x20>; clock-names = "ref"; diff --git a/Documentation/devicetree/bindings/i2c/i2c-rk3x.txt b/Documentation/devicetree/bindings/i2c/i2c-rk3x.txt index f0d71bc..0b4a85f 100644 --- a/Documentation/devicetree/bindings/i2c/i2c-rk3x.txt +++ b/Documentation/devicetree/bindings/i2c/i2c-rk3x.txt @@ -6,8 +6,8 @@ RK3xxx SoCs. Required properties : - reg : Offset and length of the register set for the device - - compatible : should be "rockchip,rk3066-i2c", "rockchip,rk3188-i2c" or - "rockchip,rk3288-i2c". + - compatible : should be "rockchip,rk3066-i2c", "rockchip,rk3188-i2c", + "rockchip,rk3228-i2c" or "rockchip,rk3288-i2c". - interrupts : interrupt number - clocks : parent clock diff --git a/Documentation/devicetree/bindings/net/cpsw.txt b/Documentation/devicetree/bindings/net/cpsw.txt index 28a4781..0ae0649 100644 --- a/Documentation/devicetree/bindings/net/cpsw.txt +++ b/Documentation/devicetree/bindings/net/cpsw.txt @@ -45,13 +45,13 @@ Required properties: Optional properties: - dual_emac_res_vlan : Specifies VID to be used to segregate the ports - mac-address : See ethernet.txt file in the same directory -- phy_id : Specifies slave phy id +- phy_id : Specifies slave phy id (deprecated, use phy-handle) - phy-handle : See ethernet.txt file in the same directory Slave sub-nodes: - fixed-link : See fixed-link.txt file in the same directory - Either the property phy_id, or the sub-node - fixed-link can be specified + +Note: Exactly one of phy_id, phy-handle, or fixed-link must be specified. Note: "ti,hwmods" field is used to fetch the base address and irq resources from TI, omap hwmod data base during device registration. diff --git a/Documentation/devicetree/bindings/net/mediatek-net.txt b/Documentation/devicetree/bindings/net/mediatek-net.txt index 5ca7929..32eaaca 100644 --- a/Documentation/devicetree/bindings/net/mediatek-net.txt +++ b/Documentation/devicetree/bindings/net/mediatek-net.txt @@ -9,7 +9,8 @@ have dual GMAC each represented by a child node.. Required properties: - compatible: Should be "mediatek,mt7623-eth" - reg: Address and length of the register set for the device -- interrupts: Should contain the frame engines interrupt +- interrupts: Should contain the three frame engines interrupts in numeric + order. These are fe_int0, fe_int1 and fe_int2. - clocks: the clock used by the core - clock-names: the names of the clock listed in the clocks property. These are "ethif", "esw", "gp2", "gp1" @@ -42,7 +43,9 @@ eth: ethernet@1b100000 { <ðsys CLK_ETHSYS_GP2>, <ðsys CLK_ETHSYS_GP1>; clock-names = "ethif", "esw", "gp2", "gp1"; - interrupts = <GIC_SPI 200 IRQ_TYPE_LEVEL_LOW>; + interrupts = <GIC_SPI 200 IRQ_TYPE_LEVEL_LOW + GIC_SPI 199 IRQ_TYPE_LEVEL_LOW + GIC_SPI 198 IRQ_TYPE_LEVEL_LOW>; power-domains = <&scpsys MT2701_POWER_DOMAIN_ETH>; resets = <ðsys MT2701_ETHSYS_ETH_RST>; reset-names = "eth"; diff --git a/Documentation/devicetree/bindings/phy/rockchip-dp-phy.txt b/Documentation/devicetree/bindings/phy/rockchip-dp-phy.txt index 50c4f9b..e3b4809 100644 --- a/Documentation/devicetree/bindings/phy/rockchip-dp-phy.txt +++ b/Documentation/devicetree/bindings/phy/rockchip-dp-phy.txt @@ -8,15 +8,19 @@ Required properties: of memory mapped region. - clock-names: from common clock binding: Required elements: "24m" -- rockchip,grf: phandle to the syscon managing the "general register files" - #phy-cells : from the generic PHY bindings, must be 0; Example: -edp_phy: edp-phy { - compatible = "rockchip,rk3288-dp-phy"; - rockchip,grf = <&grf>; - clocks = <&cru SCLK_EDP_24M>; - clock-names = "24m"; - #phy-cells = <0>; +grf: syscon@ff770000 { + compatible = "rockchip,rk3288-grf", "syscon", "simple-mfd"; + +... + + edp_phy: edp-phy { + compatible = "rockchip,rk3288-dp-phy"; + clocks = <&cru SCLK_EDP_24M>; + clock-names = "24m"; + #phy-cells = <0>; + }; }; diff --git a/Documentation/devicetree/bindings/phy/rockchip-emmc-phy.txt b/Documentation/devicetree/bindings/phy/rockchip-emmc-phy.txt index 61916f1..555cb0f 100644 --- a/Documentation/devicetree/bindings/phy/rockchip-emmc-phy.txt +++ b/Documentation/devicetree/bindings/phy/rockchip-emmc-phy.txt @@ -3,17 +3,23 @@ Rockchip EMMC PHY Required properties: - compatible: rockchip,rk3399-emmc-phy - - rockchip,grf : phandle to the syscon managing the "general - register files" - #phy-cells: must be 0 - - reg: PHY configure reg address offset in "general + - reg: PHY register address offset and length in "general register files" Example: -emmcphy: phy { - compatible = "rockchip,rk3399-emmc-phy"; - rockchip,grf = <&grf>; - reg = <0xf780>; - #phy-cells = <0>; + +grf: syscon@ff770000 { + compatible = "rockchip,rk3399-grf", "syscon", "simple-mfd"; + #address-cells = <1>; + #size-cells = <1>; + +... + + emmcphy: phy@f780 { + compatible = "rockchip,rk3399-emmc-phy"; + reg = <0xf780 0x20>; + #phy-cells = <0>; + }; }; diff --git a/Documentation/devicetree/bindings/pinctrl/img,pistachio-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/img,pistachio-pinctrl.txt index 08a4a32..0326154 100644 --- a/Documentation/devicetree/bindings/pinctrl/img,pistachio-pinctrl.txt +++ b/Documentation/devicetree/bindings/pinctrl/img,pistachio-pinctrl.txt @@ -134,12 +134,12 @@ mfio80 ddr_debug, mips_trace_data, mips_debug mfio81 dreq0, mips_trace_data, eth_debug mfio82 dreq1, mips_trace_data, eth_debug mfio83 mips_pll_lock, mips_trace_data, usb_debug -mfio84 sys_pll_lock, mips_trace_data, usb_debug -mfio85 wifi_pll_lock, mips_trace_data, sdhost_debug -mfio86 bt_pll_lock, mips_trace_data, sdhost_debug -mfio87 rpu_v_pll_lock, dreq2, socif_debug -mfio88 rpu_l_pll_lock, dreq3, socif_debug -mfio89 audio_pll_lock, dreq4, dreq5 +mfio84 audio_pll_lock, mips_trace_data, usb_debug +mfio85 rpu_v_pll_lock, mips_trace_data, sdhost_debug +mfio86 rpu_l_pll_lock, mips_trace_data, sdhost_debug +mfio87 sys_pll_lock, dreq2, socif_debug +mfio88 wifi_pll_lock, dreq3, socif_debug +mfio89 bt_pll_lock, dreq4, dreq5 tck trstn tdi diff --git a/Documentation/devicetree/bindings/pinctrl/meson,pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/meson,pinctrl.txt index 3f6a524..32f4a2d 100644 --- a/Documentation/devicetree/bindings/pinctrl/meson,pinctrl.txt +++ b/Documentation/devicetree/bindings/pinctrl/meson,pinctrl.txt @@ -1,13 +1,16 @@ == Amlogic Meson pinmux controller == Required properties for the root node: - - compatible: "amlogic,meson8-pinctrl" or "amlogic,meson8b-pinctrl" + - compatible: one of "amlogic,meson8-cbus-pinctrl" + "amlogic,meson8b-cbus-pinctrl" + "amlogic,meson8-aobus-pinctrl" + "amlogic,meson8b-aobus-pinctrl" - reg: address and size of registers controlling irq functionality === GPIO sub-nodes === -The 2 power domains of the controller (regular and always-on) are -represented as sub-nodes and each of them acts as a GPIO controller. +The GPIO bank for the controller is represented as a sub-node and it acts as a +GPIO controller. Required properties for sub-nodes are: - reg: should contain address and size for mux, pull-enable, pull and @@ -18,10 +21,6 @@ Required properties for sub-nodes are: - gpio-controller: identifies the node as a gpio controller - #gpio-cells: must be 2 -Valid sub-node names are: - - "banks" for the regular domain - - "ao-bank" for the always-on domain - === Other sub-nodes === Child nodes without the "gpio-controller" represent some desired @@ -45,7 +44,7 @@ pinctrl-bindings.txt === Example === pinctrl: pinctrl@c1109880 { - compatible = "amlogic,meson8-pinctrl"; + compatible = "amlogic,meson8-cbus-pinctrl"; reg = <0xc1109880 0x10>; #address-cells = <1>; #size-cells = <1>; @@ -61,15 +60,6 @@ pinctrl-bindings.txt #gpio-cells = <2>; }; - gpio_ao: ao-bank@c1108030 { - reg = <0xc8100014 0x4>, - <0xc810002c 0x4>, - <0xc8100024 0x8>; - reg-names = "mux", "pull", "gpio"; - gpio-controller; - #gpio-cells = <2>; - }; - nand { mux { groups = "nand_io", "nand_io_ce0", "nand_io_ce1", @@ -79,18 +69,4 @@ pinctrl-bindings.txt function = "nand"; }; }; - - uart_ao_a { - mux { - groups = "uart_tx_ao_a", "uart_rx_ao_a", - "uart_cts_ao_a", "uart_rts_ao_a"; - function = "uart_ao"; - }; - - conf { - pins = "GPIOAO_0", "GPIOAO_1", - "GPIOAO_2", "GPIOAO_3"; - bias-disable; - }; - }; }; diff --git a/Documentation/devicetree/bindings/regmap/regmap.txt b/Documentation/devicetree/bindings/regmap/regmap.txt index e98a9652..0127be3 100644 --- a/Documentation/devicetree/bindings/regmap/regmap.txt +++ b/Documentation/devicetree/bindings/regmap/regmap.txt @@ -1,50 +1,29 @@ -Device-Tree binding for regmap - -The endianness mode of CPU & Device scenarios: -Index Device Endianness properties ---------------------------------------------------- -1 BE 'big-endian' -2 LE 'little-endian' -3 Native 'native-endian' - -For one device driver, which will run in different scenarios above -on different SoCs using the devicetree, we need one way to simplify -this. +Devicetree binding for regmap Optional properties: -- {big,little,native}-endian: these are boolean properties, if absent - then the implementation will choose a default based on the device - being controlled. These properties are for register values and all - the buffers only. Native endian means that the CPU and device have - the same endianness. -Examples: -Scenario 1 : CPU in LE mode & device in LE mode. -dev: dev@40031000 { - compatible = "name"; - reg = <0x40031000 0x1000>; - ... -}; + little-endian, + big-endian, + native-endian: See common-properties.txt for a definition -Scenario 2 : CPU in LE mode & device in BE mode. -dev: dev@40031000 { - compatible = "name"; - reg = <0x40031000 0x1000>; - ... - big-endian; -}; +Note: +Regmap defaults to little-endian register access on MMIO based +devices, this is by far the most common setting. On CPU +architectures that typically run big-endian operating systems +(e.g. PowerPC), registers can be defined as big-endian and must +be marked that way in the devicetree. -Scenario 3 : CPU in BE mode & device in BE mode. -dev: dev@40031000 { - compatible = "name"; - reg = <0x40031000 0x1000>; - ... -}; +On SoCs that can be operated in both big-endian and little-endian +modes, with a single hardware switch controlling both the endianess +of the CPU and a byteswap for MMIO registers (e.g. many Broadcom MIPS +chips), "native-endian" is used to allow using the same device tree +blob in both cases. -Scenario 4 : CPU in BE mode & device in LE mode. +Examples: +Scenario 1 : a register set in big-endian mode. dev: dev@40031000 { - compatible = "name"; + compatible = "syscon"; reg = <0x40031000 0x1000>; + big-endian; ... - little-endian; }; diff --git a/Documentation/devicetree/bindings/rtc/s3c-rtc.txt b/Documentation/devicetree/bindings/rtc/s3c-rtc.txt index 1068ffc..fdde63a 100644 --- a/Documentation/devicetree/bindings/rtc/s3c-rtc.txt +++ b/Documentation/devicetree/bindings/rtc/s3c-rtc.txt @@ -15,9 +15,10 @@ Required properties: is the rtc tick interrupt. The number of cells representing a interrupt depends on the parent interrupt controller. - clocks: Must contain a list of phandle and clock specifier for the rtc - and source clocks. -- clock-names: Must contain "rtc" and "rtc_src" entries sorted in the - same order as the clocks property. + clock and in the case of a s3c6410 compatible controller, also + a source clock. +- clock-names: Must contain "rtc" and for a s3c6410 compatible controller, + a "rtc_src" sorted in the same order as the clocks property. Example: diff --git a/Documentation/devicetree/bindings/sound/davinci-mcbsp.txt b/Documentation/devicetree/bindings/sound/davinci-mcbsp.txt new file mode 100644 index 0000000..55b53e1 --- /dev/null +++ b/Documentation/devicetree/bindings/sound/davinci-mcbsp.txt @@ -0,0 +1,51 @@ +Texas Instruments DaVinci McBSP module +~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ + +This binding describes the "Multi-channel Buffered Serial Port" (McBSP) +audio interface found in some TI DaVinci processors like the OMAP-L138 or AM180x. + + +Required properties: +~~~~~~~~~~~~~~~~~~~~ +- compatible : + "ti,da850-mcbsp" : for DA850, AM180x and OPAM-L138 platforms + +- reg : physical base address and length of the controller memory mapped + region(s). +- reg-names : Should contain: + * "mpu" for the main registers (required). + * "dat" for the data FIFO (optional). + +- dmas: three element list of DMA controller phandles, DMA request line and + TC channel ordered triplets. +- dma-names: identifier string for each DMA request line in the dmas property. + These strings correspond 1:1 with the ordered pairs in dmas. The dma + identifiers must be "rx" and "tx". + +Optional properties: +~~~~~~~~~~~~~~~~~~~~ +- interrupts : Interrupt numbers for McBSP +- interrupt-names : Known interrupt names are "rx" and "tx" + +- pinctrl-0: Should specify pin control group used for this controller. +- pinctrl-names: Should contain only one value - "default", for more details + please refer to pinctrl-bindings.txt + +Example (AM1808): +~~~~~~~~~~~~~~~~~ + +mcbsp0: mcbsp@1d10000 { + compatible = "ti,da850-mcbsp"; + pinctrl-names = "default"; + pinctrl-0 = <&mcbsp0_pins>; + + reg = <0x00110000 0x1000>, + <0x00310000 0x1000>; + reg-names = "mpu", "dat"; + interrupts = <97 98>; + interrupts-names = "rx", "tx"; + dmas = <&edma0 3 1 + &edma0 2 1>; + dma-names = "tx", "rx"; + status = "okay"; +}; diff --git a/Documentation/devicetree/bindings/sound/fsl-sai.txt b/Documentation/devicetree/bindings/sound/fsl-sai.txt index 044e5d7..740b467 100644 --- a/Documentation/devicetree/bindings/sound/fsl-sai.txt +++ b/Documentation/devicetree/bindings/sound/fsl-sai.txt @@ -7,8 +7,8 @@ codec/DSP interfaces. Required properties: - - compatible : Compatible list, contains "fsl,vf610-sai" or - "fsl,imx6sx-sai". + - compatible : Compatible list, contains "fsl,vf610-sai", + "fsl,imx6sx-sai" or "fsl,imx6ul-sai" - reg : Offset and length of the register set for the device. @@ -48,6 +48,11 @@ Required properties: receive data by following their own bit clocks and frame sync clocks separately. +Optional properties (for mx6ul): + + - fsl,sai-mclk-direction-output: This is a boolean property. If present, + indicates that SAI will output the SAI MCLK clock. + Note: - If both fsl,sai-asynchronous and fsl,sai-synchronous-rx are absent, the default synchronous mode (sync Rx with Tx) will be used, which means both diff --git a/Documentation/devicetree/bindings/sound/max98371.txt b/Documentation/devicetree/bindings/sound/max98371.txt new file mode 100644 index 0000000..6c28523 --- /dev/null +++ b/Documentation/devicetree/bindings/sound/max98371.txt @@ -0,0 +1,17 @@ +max98371 codec + +This device supports I2C mode only. + +Required properties: + +- compatible : "maxim,max98371" +- reg : The chip select number on the I2C bus + +Example: + +&i2c { + max98371: max98371@0x31 { + compatible = "maxim,max98371"; + reg = <0x31>; + }; +}; diff --git a/Documentation/devicetree/bindings/sound/pcm5102a.txt b/Documentation/devicetree/bindings/sound/pcm5102a.txt new file mode 100644 index 0000000..c63ab0b6 --- /dev/null +++ b/Documentation/devicetree/bindings/sound/pcm5102a.txt @@ -0,0 +1,13 @@ +PCM5102a audio CODECs + +These devices does not use I2C or SPI. + +Required properties: + + - compatible : set as "ti,pcm5102a" + +Examples: + + pcm5102a: pcm5102a { + compatible = "ti,pcm5102a"; + }; diff --git a/Documentation/devicetree/bindings/sound/tas571x.txt b/Documentation/devicetree/bindings/sound/tas571x.txt index 0ac31d8..b4959f1 100644 --- a/Documentation/devicetree/bindings/sound/tas571x.txt +++ b/Documentation/devicetree/bindings/sound/tas571x.txt @@ -1,4 +1,4 @@ -Texas Instruments TAS5711/TAS5717/TAS5719 stereo power amplifiers +Texas Instruments TAS5711/TAS5717/TAS5719/TAS5721 stereo power amplifiers The codec is controlled through an I2C interface. It also has two other signals that can be wired up to GPIOs: reset (strongly recommended), and @@ -6,7 +6,11 @@ powerdown (optional). Required properties: -- compatible: "ti,tas5711", "ti,tas5717", or "ti,tas5719" +- compatible: should be one of the following: + - "ti,tas5711", + - "ti,tas5717", + - "ti,tas5719", + - "ti,tas5721" - reg: The I2C address of the device - #sound-dai-cells: must be equal to 0 @@ -25,6 +29,8 @@ Optional properties: - PVDD_B-supply: regulator phandle for the PVDD_B supply (5711) - PVDD_C-supply: regulator phandle for the PVDD_C supply (5711) - PVDD_D-supply: regulator phandle for the PVDD_D supply (5711) +- DRVDD-supply: regulator phandle for the DRVDD supply (5721) +- PVDD-supply: regulator phandle for the PVDD supply (5721) Example: diff --git a/Documentation/devicetree/bindings/sound/tas5720.txt b/Documentation/devicetree/bindings/sound/tas5720.txt new file mode 100644 index 0000000..806ea73 --- /dev/null +++ b/Documentation/devicetree/bindings/sound/tas5720.txt @@ -0,0 +1,25 @@ +Texas Instruments TAS5720 Mono Audio amplifier + +The TAS5720 serial control bus communicates through the I2C protocol only. The +serial bus is also used for periodic codec fault checking/reporting during +audio playback. For more product information please see the links below: + +http://www.ti.com/product/TAS5720L +http://www.ti.com/product/TAS5720M + +Required properties: + +- compatible : "ti,tas5720" +- reg : I2C slave address +- dvdd-supply : phandle to a 3.3-V supply for the digital circuitry +- pvdd-supply : phandle to a supply used for the Class-D amp and the analog + +Example: + +tas5720: tas5720@6c { + status = "okay"; + compatible = "ti,tas5720"; + reg = <0x6c>; + dvdd-supply = <&vdd_3v3_reg>; + pvdd-supply = <&_supply_reg>; +}; |