diff options
Diffstat (limited to 'Documentation/devicetree/bindings')
| -rw-r--r-- | Documentation/devicetree/bindings/ata/ahci-platform.txt | 4 | ||||
| -rw-r--r-- | Documentation/devicetree/bindings/net/cpsw.txt | 6 | ||||
| -rw-r--r-- | Documentation/devicetree/bindings/regmap/regmap.txt | 59 |
3 files changed, 26 insertions, 43 deletions
diff --git a/Documentation/devicetree/bindings/ata/ahci-platform.txt b/Documentation/devicetree/bindings/ata/ahci-platform.txt index 30df832..87adfb2 100644 --- a/Documentation/devicetree/bindings/ata/ahci-platform.txt +++ b/Documentation/devicetree/bindings/ata/ahci-platform.txt @@ -32,6 +32,10 @@ Optional properties: - target-supply : regulator for SATA target power - phys : reference to the SATA PHY node - phy-names : must be "sata-phy" +- ports-implemented : Mask that indicates which ports that the HBA supports + are available for software to use. Useful if PORTS_IMPL + is not programmed by the BIOS, which is true with + some embedded SOC's. Required properties when using sub-nodes: - #address-cells : number of cells to encode an address diff --git a/Documentation/devicetree/bindings/net/cpsw.txt b/Documentation/devicetree/bindings/net/cpsw.txt index 28a4781..0ae0649 100644 --- a/Documentation/devicetree/bindings/net/cpsw.txt +++ b/Documentation/devicetree/bindings/net/cpsw.txt @@ -45,13 +45,13 @@ Required properties: Optional properties: - dual_emac_res_vlan : Specifies VID to be used to segregate the ports - mac-address : See ethernet.txt file in the same directory -- phy_id : Specifies slave phy id +- phy_id : Specifies slave phy id (deprecated, use phy-handle) - phy-handle : See ethernet.txt file in the same directory Slave sub-nodes: - fixed-link : See fixed-link.txt file in the same directory - Either the property phy_id, or the sub-node - fixed-link can be specified + +Note: Exactly one of phy_id, phy-handle, or fixed-link must be specified. Note: "ti,hwmods" field is used to fetch the base address and irq resources from TI, omap hwmod data base during device registration. diff --git a/Documentation/devicetree/bindings/regmap/regmap.txt b/Documentation/devicetree/bindings/regmap/regmap.txt index e98a9652..0127be3 100644 --- a/Documentation/devicetree/bindings/regmap/regmap.txt +++ b/Documentation/devicetree/bindings/regmap/regmap.txt @@ -1,50 +1,29 @@ -Device-Tree binding for regmap - -The endianness mode of CPU & Device scenarios: -Index Device Endianness properties ---------------------------------------------------- -1 BE 'big-endian' -2 LE 'little-endian' -3 Native 'native-endian' - -For one device driver, which will run in different scenarios above -on different SoCs using the devicetree, we need one way to simplify -this. +Devicetree binding for regmap Optional properties: -- {big,little,native}-endian: these are boolean properties, if absent - then the implementation will choose a default based on the device - being controlled. These properties are for register values and all - the buffers only. Native endian means that the CPU and device have - the same endianness. -Examples: -Scenario 1 : CPU in LE mode & device in LE mode. -dev: dev@40031000 { - compatible = "name"; - reg = <0x40031000 0x1000>; - ... -}; + little-endian, + big-endian, + native-endian: See common-properties.txt for a definition -Scenario 2 : CPU in LE mode & device in BE mode. -dev: dev@40031000 { - compatible = "name"; - reg = <0x40031000 0x1000>; - ... - big-endian; -}; +Note: +Regmap defaults to little-endian register access on MMIO based +devices, this is by far the most common setting. On CPU +architectures that typically run big-endian operating systems +(e.g. PowerPC), registers can be defined as big-endian and must +be marked that way in the devicetree. -Scenario 3 : CPU in BE mode & device in BE mode. -dev: dev@40031000 { - compatible = "name"; - reg = <0x40031000 0x1000>; - ... -}; +On SoCs that can be operated in both big-endian and little-endian +modes, with a single hardware switch controlling both the endianess +of the CPU and a byteswap for MMIO registers (e.g. many Broadcom MIPS +chips), "native-endian" is used to allow using the same device tree +blob in both cases. -Scenario 4 : CPU in BE mode & device in LE mode. +Examples: +Scenario 1 : a register set in big-endian mode. dev: dev@40031000 { - compatible = "name"; + compatible = "syscon"; reg = <0x40031000 0x1000>; + big-endian; ... - little-endian; }; |