diff options
Diffstat (limited to 'Documentation/devicetree/bindings')
9 files changed, 52 insertions, 8 deletions
diff --git a/Documentation/devicetree/bindings/arm/cpus.txt b/Documentation/devicetree/bindings/arm/cpus.txt index d6b794c..91e6e5c 100644 --- a/Documentation/devicetree/bindings/arm/cpus.txt +++ b/Documentation/devicetree/bindings/arm/cpus.txt @@ -199,6 +199,7 @@ nodes to be present and contain the properties described below. "qcom,kpss-acc-v1" "qcom,kpss-acc-v2" "rockchip,rk3066-smp" + "ste,dbx500-smp" - cpu-release-addr Usage: required for systems that have an "enable-method" diff --git a/Documentation/devicetree/bindings/dma/apm-xgene-dma.txt b/Documentation/devicetree/bindings/dma/apm-xgene-dma.txt index d305876..c53e0b0 100644 --- a/Documentation/devicetree/bindings/dma/apm-xgene-dma.txt +++ b/Documentation/devicetree/bindings/dma/apm-xgene-dma.txt @@ -35,7 +35,7 @@ Example: device_type = "dma"; reg = <0x0 0x1f270000 0x0 0x10000>, <0x0 0x1f200000 0x0 0x10000>, - <0x0 0x1b008000 0x0 0x2000>, + <0x0 0x1b000000 0x0 0x400000>, <0x0 0x1054a000 0x0 0x100>; interrupts = <0x0 0x82 0x4>, <0x0 0xb8 0x4>, diff --git a/Documentation/devicetree/bindings/drm/imx/fsl-imx-drm.txt b/Documentation/devicetree/bindings/drm/imx/fsl-imx-drm.txt index e75f0e5..971c3ee 100644 --- a/Documentation/devicetree/bindings/drm/imx/fsl-imx-drm.txt +++ b/Documentation/devicetree/bindings/drm/imx/fsl-imx-drm.txt @@ -65,8 +65,10 @@ Optional properties: - edid: verbatim EDID data block describing attached display. - ddc: phandle describing the i2c bus handling the display data channel -- port: A port node with endpoint definitions as defined in +- port@[0-1]: Port nodes with endpoint definitions as defined in Documentation/devicetree/bindings/media/video-interfaces.txt. + Port 0 is the input port connected to the IPU display interface, + port 1 is the output port connected to a panel. example: @@ -75,9 +77,29 @@ display@di0 { edid = [edid-data]; interface-pix-fmt = "rgb24"; - port { + port@0 { + reg = <0>; + display_in: endpoint { remote-endpoint = <&ipu_di0_disp0>; }; }; + + port@1 { + reg = <1>; + + display_out: endpoint { + remote-endpoint = <&panel_in>; + }; + }; +}; + +panel { + ... + + port { + panel_in: endpoint { + remote-endpoint = <&display_out>; + }; + }; }; diff --git a/Documentation/devicetree/bindings/iommu/arm,smmu-v3.txt b/Documentation/devicetree/bindings/iommu/arm,smmu-v3.txt index c03eec1..3443e0f 100644 --- a/Documentation/devicetree/bindings/iommu/arm,smmu-v3.txt +++ b/Documentation/devicetree/bindings/iommu/arm,smmu-v3.txt @@ -35,3 +35,6 @@ the PCIe specification. NOTE: this only applies to the SMMU itself, not masters connected upstream of the SMMU. + +- hisilicon,broken-prefetch-cmd + : Avoid sending CMD_PREFETCH_* commands to the SMMU. diff --git a/Documentation/devicetree/bindings/mmc/fsl-imx-esdhc.txt b/Documentation/devicetree/bindings/mmc/fsl-imx-esdhc.txt index 5d0376b..211e778 100644 --- a/Documentation/devicetree/bindings/mmc/fsl-imx-esdhc.txt +++ b/Documentation/devicetree/bindings/mmc/fsl-imx-esdhc.txt @@ -17,7 +17,6 @@ Required properties: "fsl,imx6sx-usdhc" Optional properties: -- fsl,cd-controller : Indicate to use controller internal card detection - fsl,wp-controller : Indicate to use controller internal write protection - fsl,delay-line : Specify the number of delay cells for override mode. This is used to set the clock delay for DLL(Delay Line) on override mode @@ -35,7 +34,6 @@ esdhc@70004000 { compatible = "fsl,imx51-esdhc"; reg = <0x70004000 0x4000>; interrupts = <1>; - fsl,cd-controller; fsl,wp-controller; }; diff --git a/Documentation/devicetree/bindings/phy/ti-phy.txt b/Documentation/devicetree/bindings/phy/ti-phy.txt index 305e3df..9cf9446 100644 --- a/Documentation/devicetree/bindings/phy/ti-phy.txt +++ b/Documentation/devicetree/bindings/phy/ti-phy.txt @@ -82,6 +82,9 @@ Optional properties: - id: If there are multiple instance of the same type, in order to differentiate between each instance "id" can be used (e.g., multi-lane PCIe PHY). If "id" is not provided, it is set to default value of '1'. + - syscon-pllreset: Handle to system control region that contains the + CTRL_CORE_SMA_SW_0 register and register offset to the CTRL_CORE_SMA_SW_0 + register that contains the SATA_PLL_SOFT_RESET bit. Only valid for sata_phy. This is usually a subnode of ocp2scp to which it is connected. @@ -100,3 +103,16 @@ usb3phy@4a084400 { "sysclk", "refclk"; }; + +sata_phy: phy@4A096000 { + compatible = "ti,phy-pipe3-sata"; + reg = <0x4A096000 0x80>, /* phy_rx */ + <0x4A096400 0x64>, /* phy_tx */ + <0x4A096800 0x40>; /* pll_ctrl */ + reg-names = "phy_rx", "phy_tx", "pll_ctrl"; + ctrl-module = <&omap_control_sata>; + clocks = <&sys_clkin1>, <&sata_ref_clk>; + clock-names = "sysclk", "refclk"; + syscon-pllreset = <&scm_conf 0x3fc>; + #phy-cells = <0>; +}; diff --git a/Documentation/devicetree/bindings/sound/mt8173-max98090.txt b/Documentation/devicetree/bindings/sound/mt8173-max98090.txt index 829bd26..519e97c 100644 --- a/Documentation/devicetree/bindings/sound/mt8173-max98090.txt +++ b/Documentation/devicetree/bindings/sound/mt8173-max98090.txt @@ -3,11 +3,13 @@ MT8173 with MAX98090 CODEC Required properties: - compatible : "mediatek,mt8173-max98090" - mediatek,audio-codec: the phandle of the MAX98090 audio codec +- mediatek,platform: the phandle of MT8173 ASoC platform Example: sound { compatible = "mediatek,mt8173-max98090"; mediatek,audio-codec = <&max98090>; + mediatek,platform = <&afe>; }; diff --git a/Documentation/devicetree/bindings/sound/mt8173-rt5650-rt5676.txt b/Documentation/devicetree/bindings/sound/mt8173-rt5650-rt5676.txt index 61e98c9..f205ce9 100644 --- a/Documentation/devicetree/bindings/sound/mt8173-rt5650-rt5676.txt +++ b/Documentation/devicetree/bindings/sound/mt8173-rt5650-rt5676.txt @@ -3,11 +3,13 @@ MT8173 with RT5650 RT5676 CODECS Required properties: - compatible : "mediatek,mt8173-rt5650-rt5676" - mediatek,audio-codec: the phandles of rt5650 and rt5676 codecs +- mediatek,platform: the phandle of MT8173 ASoC platform Example: sound { compatible = "mediatek,mt8173-rt5650-rt5676"; mediatek,audio-codec = <&rt5650 &rt5676>; + mediatek,platform = <&afe>; }; diff --git a/Documentation/devicetree/bindings/spi/spi-ath79.txt b/Documentation/devicetree/bindings/spi/spi-ath79.txt index f1ad9c3..9c696fa 100644 --- a/Documentation/devicetree/bindings/spi/spi-ath79.txt +++ b/Documentation/devicetree/bindings/spi/spi-ath79.txt @@ -3,7 +3,7 @@ Binding for Qualcomm Atheros AR7xxx/AR9xxx SPI controller Required properties: - compatible: has to be "qca,<soc-type>-spi", "qca,ar7100-spi" as fallback. - reg: Base address and size of the controllers memory area -- clocks: phandle to the AHB clock. +- clocks: phandle of the AHB clock. - clock-names: has to be "ahb". - #address-cells: <1>, as required by generic SPI binding. - #size-cells: <0>, also as required by generic SPI binding. @@ -12,9 +12,9 @@ Child nodes as per the generic SPI binding. Example: - spi@1F000000 { + spi@1f000000 { compatible = "qca,ar9132-spi", "qca,ar7100-spi"; - reg = <0x1F000000 0x10>; + reg = <0x1f000000 0x10>; clocks = <&pll 2>; clock-names = "ahb"; |