5 files changed, 93 insertions, 11 deletions
diff --git a/Documentation/devicetree/bindings/input/cap1106.txt b/Documentation/devicetree/bindings/input/cap11xx.txt
index 4b46390..7d0a300 100644
--- a/Documentation/devicetree/bindings/input/cap1106.txt
+++ b/Documentation/devicetree/bindings/input/cap11xx.txt
@@ -1,14 +1,16 @@
-Device tree bindings for Microchip CAP1106, 6 channel capacitive touch sensor
+Device tree bindings for Microchip CAP11xx based capacitive touch sensors
 
-The node for this driver must be a child of a I2C controller node, as the
+The node for this device must be a child of a I2C controller node, as the
 device communication via I2C only.
 
 Required properties:
 
-	compatible:		Must be "microchip,cap1106"
+	compatible:		Must contain one of:
+					"microchip,cap1106"
+					"microchip,cap1126"
+					"microchip,cap1188"
 
 	reg:			The I2C slave address of the device.
-				Only 0x28 is valid.
 
 	interrupts:		Property describing the interrupt line the
 				device's ALERT#/CM_IRQ# pin is connected to.
@@ -26,6 +28,10 @@ Optional properties:
 				Valid values are 1, 2, 4, and 8.
 				By default, a gain of 1 is set.
 
+	microchip,irq-active-high:	By default the interrupt pin is active low
+				open drain. This property allows using the active
+				high push-pull output.
+
 	linux,keycodes:		Specifies an array of numeric keycode values to
 				be used for the channels. If this property is
 				omitted, KEY_A, KEY_B, etc are used as
@@ -43,11 +49,11 @@ i2c_controller {
 		autorepeat;
 		microchip,sensor-gain = <2>;
 
-		linux,keycodes = <103		/* KEY_UP */
-				  106		/* KEY_RIGHT */
-				  108		/* KEY_DOWN */
-				  105		/* KEY_LEFT */
-				  109		/* KEY_PAGEDOWN */
-				  104>;		/* KEY_PAGEUP */
+		linux,keycodes = <103>,		/* KEY_UP */
+				 <106>,		/* KEY_RIGHT */
+				 <108>,		/* KEY_DOWN */
+				 <105>,		/* KEY_LEFT */
+				 <109>,		/* KEY_PAGEDOWN */
+				 <104>;		/* KEY_PAGEUP */
 	};
 }
diff --git a/Documentation/devicetree/bindings/input/elan_i2c.txt b/Documentation/devicetree/bindings/input/elan_i2c.txt
new file mode 100644
index 0000000..ee3242c
--- /dev/null
+++ b/Documentation/devicetree/bindings/input/elan_i2c.txt
@@ -0,0 +1,34 @@
+Elantech I2C Touchpad
+
+Required properties:
+- compatible: must be "elan,ekth3000".
+- reg: I2C address of the chip.
+- interrupt-parent: a phandle for the interrupt controller (see interrupt
+  binding[0]).
+- interrupts: interrupt to which the chip is connected (see interrupt
+  binding[0]).
+
+Optional properties:
+- wakeup-source: touchpad can be used as a wakeup source.
+- pinctrl-names: should be "default" (see pinctrl binding [1]).
+- pinctrl-0: a phandle pointing to the pin settings for the device (see
+  pinctrl binding [1]).
+- vcc-supply: a phandle for the regulator supplying 3.3V power.
+
+[0]: Documentation/devicetree/bindings/interrupt-controller/interrupts.txt
+[1]: Documentation/devicetree/bindings/pinctrl/pinctrl-bindings.txt
+
+Example:
+	&i2c1 {
+		/* ... */
+
+		touchpad@15 {
+			compatible = "elan,ekth3000";
+			reg = <0x15>;
+			interrupt-parent = <&gpio4>;
+			interrupts = <0x0 IRQ_TYPE_EDGE_FALLING>;
+			wakeup-source;
+		};
+
+		/* ... */
+	};
diff --git a/Documentation/devicetree/bindings/input/elants_i2c.txt b/Documentation/devicetree/bindings/input/elants_i2c.txt
new file mode 100644
index 0000000..a765232
--- /dev/null
+++ b/Documentation/devicetree/bindings/input/elants_i2c.txt
@@ -0,0 +1,33 @@
+Elantech I2C Touchscreen
+
+Required properties:
+- compatible: must be "elan,ekth3500".
+- reg: I2C address of the chip.
+- interrupt-parent: a phandle for the interrupt controller (see interrupt
+  binding[0]).
+- interrupts: interrupt to which the chip is connected (see interrupt
+  binding[0]).
+
+Optional properties:
+- wakeup-source: touchscreen can be used as a wakeup source.
+- pinctrl-names: should be "default" (see pinctrl binding [1]).
+- pinctrl-0: a phandle pointing to the pin settings for the device (see
+  pinctrl binding [1]).
+
+[0]: Documentation/devicetree/bindings/interrupt-controller/interrupts.txt
+[1]: Documentation/devicetree/bindings/pinctrl/pinctrl-bindings.txt
+
+Example:
+	&i2c1 {
+		/* ... */
+
+		touchscreen@10 {
+			compatible = "elan,ekth3500";
+			reg = <0x10>;
+			interrupt-parent = <&gpio4>;
+			interrupts = <0x0 IRQ_TYPE_EDGE_FALLING>;
+			wakeup-source;
+		};
+
+		/* ... */
+	};
diff --git a/Documentation/devicetree/bindings/input/gpio-keys.txt b/Documentation/devicetree/bindings/input/gpio-keys.txt
index 5c2c021..a4a38fc 100644
--- a/Documentation/devicetree/bindings/input/gpio-keys.txt
+++ b/Documentation/devicetree/bindings/input/gpio-keys.txt
@@ -10,10 +10,13 @@ Optional properties:
 Each button (key) is represented as a sub-node of "gpio-keys":
 Subnode properties:
 
-	- gpios: OF device-tree gpio specification.
 	- label: Descriptive name of the key.
 	- linux,code: Keycode to emit.
 
+Required mutual exclusive subnode-properties:
+	- gpios: OF device-tree gpio specification.
+	- interrupts: the interrupt line for that input
+
 Optional subnode-properties:
 	- linux,input-type: Specify event type this button/key generates.
 	  If not specified defaults to <1> == EV_KEY.
@@ -33,4 +36,9 @@ Example nodes:
 				linux,code = <103>;
 				gpios = <&gpio1 0 1>;
 			};
+			button@22 {
+				label = "GPIO Key DOWN";
+				linux,code = <108>;
+				interrupts = <1 IRQ_TYPE_LEVEL_HIGH 7>;
+			};
 			...
diff --git a/Documentation/devicetree/bindings/vendor-prefixes.txt b/Documentation/devicetree/bindings/vendor-prefixes.txt
index 423d474..b1df0ad 100644
--- a/Documentation/devicetree/bindings/vendor-prefixes.txt
+++ b/Documentation/devicetree/bindings/vendor-prefixes.txt
@@ -47,6 +47,7 @@ dlink	D-Link Corporation
 dmo	Data Modul AG
 ebv	EBV Elektronik
 edt	Emerging Display Technologies
+elan	Elan Microelectronic Corp.
 emmicro	EM Microelectronic
 energymicro	Silicon Laboratories (formerly Energy Micro AS)
 epcos	EPCOS AG