diff options
Diffstat (limited to 'Documentation/devicetree')
3 files changed, 89 insertions, 12 deletions
diff --git a/Documentation/devicetree/bindings/regulator/mt6311-regulator.txt b/Documentation/devicetree/bindings/regulator/mt6311-regulator.txt new file mode 100644 index 0000000..02649d8 --- /dev/null +++ b/Documentation/devicetree/bindings/regulator/mt6311-regulator.txt @@ -0,0 +1,35 @@ +Mediatek MT6311 Regulator Driver + +Required properties: +- compatible: "mediatek,mt6311-regulator" +- reg: I2C slave address, usually 0x6b. +- regulators: List of regulators provided by this controller. It is named + to VDVFS and VBIASN. + The definition for each of these nodes is defined using the standard binding + for regulators at Documentation/devicetree/bindings/regulator/regulator.txt. + +The valid names for regulators are: +BUCK: + VDVFS +LDO: + VBIASN + +Example: + mt6311: pmic@6b { + compatible = "mediatek,mt6311-regulator"; + reg = <0x6b>; + + regulators { + mt6311_vcpu_reg: VDVFS { + regulator-name = "VDVFS"; + regulator-min-microvolt = < 600000>; + regulator-max-microvolt = <1400000>; + regulator-ramp-delay = <10000>; + }; + mt6311_ldo_reg: VBIASN { + regulator-name = "VBIASN"; + regulator-min-microvolt = <200000>; + regulator-max-microvolt = <800000>; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/regulator/pwm-regulator.txt b/Documentation/devicetree/bindings/regulator/pwm-regulator.txt index ce91f61..ed936f0 100644 --- a/Documentation/devicetree/bindings/regulator/pwm-regulator.txt +++ b/Documentation/devicetree/bindings/regulator/pwm-regulator.txt @@ -1,27 +1,68 @@ -pwm regulator bindings +Bindings for the Generic PWM Regulator +====================================== + +Currently supports 2 modes of operation: + +Voltage Table: When in this mode, a voltage table (See below) of + predefined voltage <=> duty-cycle values must be + provided via DT. Limitations are that the regulator can + only operate at the voltages supplied in the table. + Intermediary duty-cycle values which would normally + allow finer grained voltage selection are ignored and + rendered useless. Although more control is given to + the user if the assumptions made in continuous-voltage + mode do not reign true. + +Continuous Voltage: This mode uses the regulator's maximum and minimum + supplied voltages specified in the + regulator-{min,max}-microvolt properties to calculate + appropriate duty-cycle values. This allows for a much + more fine grained solution when compared with + voltage-table mode above. This solution does make an + assumption that a %50 duty-cycle value will cause the + regulator voltage to run at half way between the + supplied max_uV and min_uV values. Required properties: -- compatible: Should be "pwm-regulator" -- pwms: OF device-tree PWM specification (see PWM binding pwm.txt) -- voltage-table: voltage and duty table, include 2 members in each set of - brackets, first one is voltage(unit: uv), the next is duty(unit: percent) +-------------------- +- compatible: Should be "pwm-regulator" + +- pwms: PWM specification (See: ../pwm/pwm.txt) + +Only required for Voltage Table Mode: +- voltage-table: Voltage and Duty-Cycle table consisting of 2 cells + First cell is voltage in microvolts (uV) + Second cell is duty-cycle in percent (%) + +NB: To be clear, if voltage-table is provided, then the device will be used +in Voltage Table Mode. If no voltage-table is provided, then the device will +be used in Continuous Voltage Mode. -Any property defined as part of the core regulator binding defined in -regulator.txt can also be used. +Any property defined as part of the core regulator binding can also be used. +(See: ../regulator/regulator.txt) -Example: +Continuous Voltage Example: pwm_regulator { compatible = "pwm-regulator; pwms = <&pwm1 0 8448 0>; + regulator-min-microvolt = <1016000>; + regulator-max-microvolt = <1114000>; + regulator-name = "vdd_logic"; + }; +Voltage Table Example: + pwm_regulator { + compatible = "pwm-regulator; + pwms = <&pwm1 0 8448 0>; + regulator-min-microvolt = <1016000>; + regulator-max-microvolt = <1114000>; + regulator-name = "vdd_logic"; + + /* Voltage Duty-Cycle */ voltage-table = <1114000 0>, <1095000 10>, <1076000 20>, <1056000 30>, <1036000 40>, <1016000 50>; - - regulator-min-microvolt = <1016000>; - regulator-max-microvolt = <1114000>; - regulator-name = "vdd_logic"; }; diff --git a/Documentation/devicetree/bindings/regulator/regulator.txt b/Documentation/devicetree/bindings/regulator/regulator.txt index db88feb..24bd422 100644 --- a/Documentation/devicetree/bindings/regulator/regulator.txt +++ b/Documentation/devicetree/bindings/regulator/regulator.txt @@ -42,6 +42,7 @@ Optional properties: - regulator-system-load: Load in uA present on regulator that is not captured by any consumer request. - regulator-pull-down: Enable pull down resistor when the regulator is disabled. +- regulator-over-current-protection: Enable over current protection. Deprecated properties: - regulator-compatible: If a regulator chip contains multiple |