diff options
Diffstat (limited to 'Documentation/devicetree')
242 files changed, 5747 insertions, 305 deletions
diff --git a/Documentation/devicetree/bindings/arc/archs-pct.txt b/Documentation/devicetree/bindings/arc/archs-pct.txt index 1ae98b87..e4b9dce 100644 --- a/Documentation/devicetree/bindings/arc/archs-pct.txt +++ b/Documentation/devicetree/bindings/arc/archs-pct.txt @@ -2,7 +2,7 @@ The ARC HS can be configured with a pipeline performance monitor for counting CPU and cache events like cache misses and hits. Like conventional PCT there -are 100+ hardware conditions dynamically mapped to upto 32 counters. +are 100+ hardware conditions dynamically mapped to up to 32 counters. It also supports overflow interrupts. Required properties: diff --git a/Documentation/devicetree/bindings/arc/pct.txt b/Documentation/devicetree/bindings/arc/pct.txt index 7b95884..4e874d9 100644 --- a/Documentation/devicetree/bindings/arc/pct.txt +++ b/Documentation/devicetree/bindings/arc/pct.txt @@ -2,7 +2,7 @@ The ARC700 can be configured with a pipeline performance monitor for counting CPU and cache events like cache misses and hits. Like conventional PCT there -are 100+ hardware conditions dynamically mapped to upto 32 counters +are 100+ hardware conditions dynamically mapped to up to 32 counters Note that: * The ARC 700 PCT does not support interrupts; although HW events may be diff --git a/Documentation/devicetree/bindings/arm/altera/socfpga-eccmgr.txt b/Documentation/devicetree/bindings/arm/altera/socfpga-eccmgr.txt new file mode 100644 index 0000000..885f93d --- /dev/null +++ b/Documentation/devicetree/bindings/arm/altera/socfpga-eccmgr.txt @@ -0,0 +1,49 @@ +Altera SoCFPGA ECC Manager +This driver uses the EDAC framework to implement the SOCFPGA ECC Manager. +The ECC Manager counts and corrects single bit errors and counts/handles +double bit errors which are uncorrectable. + +Required Properties: +- compatible : Should be "altr,socfpga-ecc-manager" +- #address-cells: must be 1 +- #size-cells: must be 1 +- ranges : standard definition, should translate from local addresses + +Subcomponents: + +L2 Cache ECC +Required Properties: +- compatible : Should be "altr,socfpga-l2-ecc" +- reg : Address and size for ECC error interrupt clear registers. +- interrupts : Should be single bit error interrupt, then double bit error + interrupt. Note the rising edge type. + +On Chip RAM ECC +Required Properties: +- compatible : Should be "altr,socfpga-ocram-ecc" +- reg : Address and size for ECC error interrupt clear registers. +- iram : phandle to On-Chip RAM definition. +- interrupts : Should be single bit error interrupt, then double bit error + interrupt. Note the rising edge type. + +Example: + + eccmgr: eccmgr@ffd08140 { + compatible = "altr,socfpga-ecc-manager"; + #address-cells = <1>; + #size-cells = <1>; + ranges; + + l2-ecc@ffd08140 { + compatible = "altr,socfpga-l2-ecc"; + reg = <0xffd08140 0x4>; + interrupts = <0 36 1>, <0 37 1>; + }; + + ocram-ecc@ffd08144 { + compatible = "altr,socfpga-ocram-ecc"; + reg = <0xffd08144 0x4>; + iram = <&ocram>; + interrupts = <0 178 1>, <0 179 1>; + }; + }; diff --git a/Documentation/devicetree/bindings/arm/amlogic.txt b/Documentation/devicetree/bindings/arm/amlogic.txt index 1dfee20..8a5122a 100644 --- a/Documentation/devicetree/bindings/arm/amlogic.txt +++ b/Documentation/devicetree/bindings/arm/amlogic.txt @@ -13,8 +13,15 @@ Boards with the Amlogic Meson8b SoC shall have the following properties: Required root node property: compatible: "amlogic,meson8b"; +Boards with the Amlogic Meson GXBaby SoC shall have the following properties: + Required root node property: + compatible: "amlogic,meson-gxbb"; + Board compatible values: - "geniatech,atv1200" (Meson6) - "minix,neo-x8" (Meson8) - "tronfy,mxq" (Meson8b) - "hardkernel,odroid-c1" (Meson8b) + - "tronsmart,vega-s95-pro", "tronsmart,vega-s95" (Meson gxbb) + - "tronsmart,vega-s95-meta", "tronsmart,vega-s95" (Meson gxbb) + - "tronsmart,vega-s95-telos", "tronsmart,vega-s95" (Meson gxbb) diff --git a/Documentation/devicetree/bindings/arm/arm-boards b/Documentation/devicetree/bindings/arm/arm-boards index 1a70997..0226bc2 100644 --- a/Documentation/devicetree/bindings/arm/arm-boards +++ b/Documentation/devicetree/bindings/arm/arm-boards @@ -123,7 +123,9 @@ Required nodes: - syscon: some subnode of the RealView SoC node must be a system controller node pointing to the control registers, - with the compatible string set to one of these tuples: + with the compatible string set to one of these: + "arm,realview-eb11mp-revb-syscon", "arm,realview-eb-syscon", "syscon" + "arm,realview-eb11mp-revc-syscon", "arm,realview-eb-syscon", "syscon" "arm,realview-eb-syscon", "syscon" "arm,realview-pb1176-syscon", "syscon" "arm,realview-pb11mp-syscon", "syscon" @@ -180,6 +182,7 @@ described under the RS1 memory mapping. Required properties (in root node): compatible = "arm,juno"; /* For Juno r0 board */ compatible = "arm,juno-r1"; /* For Juno r1 board */ + compatible = "arm,juno-r2"; /* For Juno r2 board */ Required nodes: The description for the board must include: diff --git a/Documentation/devicetree/bindings/arm/axis.txt b/Documentation/devicetree/bindings/arm/axis.txt new file mode 100644 index 0000000..ae345e1 --- /dev/null +++ b/Documentation/devicetree/bindings/arm/axis.txt @@ -0,0 +1,29 @@ +Axis Communications AB +ARTPEC series SoC Device Tree Bindings + +ARTPEC-6 ARM SoC +================ + +Required root node properties: +- compatible = "axis,artpec6"; + +ARTPEC-6 System Controller +-------------------------- + +The ARTPEC-6 has a system controller with mixed functions controlling DMA, PCIe +and resets. + +Required properties: +- compatible: "axis,artpec6-syscon", "syscon" +- reg: Address and length of the register bank. + +Example: + syscon { + compatible = "axis,artpec6-syscon", "syscon"; + reg = <0xf8000000 0x48>; + }; + +ARTPEC-6 Development board: +--------------------------- +Required root node properties: +- compatible = "axis,artpec6-dev-board", "axis,artpec6"; diff --git a/Documentation/devicetree/bindings/arm/bcm/brcm,vulcan-soc.txt b/Documentation/devicetree/bindings/arm/bcm/brcm,vulcan-soc.txt new file mode 100644 index 0000000..223ed34 --- /dev/null +++ b/Documentation/devicetree/bindings/arm/bcm/brcm,vulcan-soc.txt @@ -0,0 +1,10 @@ +Broadcom Vulcan device tree bindings +------------------------------------ + +Boards with Broadcom Vulcan shall have the following root property: + +Broadcom Vulcan Evaluation Board: + compatible = "brcm,vulcan-eval", "brcm,vulcan-soc"; + +Generic Vulcan board: + compatible = "brcm,vulcan-soc"; diff --git a/Documentation/devicetree/bindings/arm/cci.txt b/Documentation/devicetree/bindings/arm/cci.txt index aef1d20..a1a5a7e 100644 --- a/Documentation/devicetree/bindings/arm/cci.txt +++ b/Documentation/devicetree/bindings/arm/cci.txt @@ -34,6 +34,7 @@ specific to ARM. Definition: must contain one of the following: "arm,cci-400" "arm,cci-500" + "arm,cci-550" - reg Usage: required @@ -101,6 +102,7 @@ specific to ARM. "arm,cci-400-pmu" - DEPRECATED, permitted only where OS has secure acces to CCI registers "arm,cci-500-pmu,r0" + "arm,cci-550-pmu,r0" - reg: Usage: required Value type: Integer cells. A register entry, expressed diff --git a/Documentation/devicetree/bindings/arm/cpus.txt b/Documentation/devicetree/bindings/arm/cpus.txt index ae9be07..3f0cbbb 100644 --- a/Documentation/devicetree/bindings/arm/cpus.txt +++ b/Documentation/devicetree/bindings/arm/cpus.txt @@ -167,6 +167,7 @@ nodes to be present and contain the properties described below. "arm,cortex-r5" "arm,cortex-r7" "brcm,brahma-b15" + "brcm,vulcan" "cavium,thunder" "faraday,fa526" "intel,sa110" @@ -178,6 +179,7 @@ nodes to be present and contain the properties described below. "marvell,sheeva-v5" "nvidia,tegra132-denver" "qcom,krait" + "qcom,kryo" "qcom,scorpion" - enable-method Value type: <stringlist> @@ -190,7 +192,6 @@ nodes to be present and contain the properties described below. can be one of: "allwinner,sun6i-a31" "allwinner,sun8i-a23" - "arm,psci" "arm,realview-smp" "brcm,bcm-nsp-smp" "brcm,brahma-b15" @@ -250,7 +251,7 @@ nodes to be present and contain the properties described below. Usage: optional Value type: <prop-encoded-array> Definition: A u32 value that represents the running time dynamic - power coefficient in units of mW/MHz/uVolt^2. The + power coefficient in units of mW/MHz/uV^2. The coefficient can either be calculated from power measurements or derived by analysis. diff --git a/Documentation/devicetree/bindings/arm/fw-cfg.txt b/Documentation/devicetree/bindings/arm/fw-cfg.txt index 953fb64..fd54e1d 100644 --- a/Documentation/devicetree/bindings/arm/fw-cfg.txt +++ b/Documentation/devicetree/bindings/arm/fw-cfg.txt @@ -11,43 +11,9 @@ QEMU exposes the control and data register to ARM guests as memory mapped registers; their location is communicated to the guest's UEFI firmware in the DTB that QEMU places at the bottom of the guest's DRAM. -The guest writes a selector value (a key) to the selector register, and then -can read the corresponding data (produced by QEMU) via the data register. If -the selected entry is writable, the guest can rewrite it through the data -register. +The authoritative guest-side hardware interface documentation to the fw_cfg +device can be found in "docs/specs/fw_cfg.txt" in the QEMU source tree. -The selector register takes keys in big endian byte order. - -The data register allows accesses with 8, 16, 32 and 64-bit width (only at -offset 0 of the register). Accesses larger than a byte are interpreted as -arrays, bundled together only for better performance. The bytes constituting -such a word, in increasing address order, correspond to the bytes that would -have been transferred by byte-wide accesses in chronological order. - -The interface allows guest firmware to download various parameters and blobs -that affect how the firmware works and what tables it installs for the guest -OS. For example, boot order of devices, ACPI tables, SMBIOS tables, kernel and -initrd images for direct kernel booting, virtual machine UUID, SMP information, -virtual NUMA topology, and so on. - -The authoritative registry of the valid selector values and their meanings is -the QEMU source code; the structure of the data blobs corresponding to the -individual key values is also defined in the QEMU source code. - -The presence of the registers can be verified by selecting the "signature" blob -with key 0x0000, and reading four bytes from the data register. The returned -signature is "QEMU". - -The outermost protocol (involving the write / read sequences of the control and -data registers) is expected to be versioned, and/or described by feature bits. -The interface revision / feature bitmap can be retrieved with key 0x0001. The -blob to be read from the data register has size 4, and it is to be interpreted -as a uint32_t value in little endian byte order. The current value -(corresponding to the above outer protocol) is zero. - -The guest kernel is not expected to use these registers (although it is -certainly allowed to); the device tree bindings are documented here because -this is where device tree bindings reside in general. Required properties: diff --git a/Documentation/devicetree/bindings/arm/keystone/keystone.txt b/Documentation/devicetree/bindings/arm/keystone/keystone.txt index 3090a8a..48f6703 100644 --- a/Documentation/devicetree/bindings/arm/keystone/keystone.txt +++ b/Documentation/devicetree/bindings/arm/keystone/keystone.txt @@ -22,6 +22,8 @@ SoCs: compatible = "ti,k2l", "ti,keystone" - Keystone 2 Edison compatible = "ti,k2e", "ti,keystone" +- K2G + compatible = "ti,k2g", "ti,keystone" Boards: - Keystone 2 Hawking/Kepler EVM @@ -32,3 +34,6 @@ Boards: - Keystone 2 Edison EVM compatible = "ti,k2e-evm", "ti,k2e", "ti,keystone" + +- K2G EVM + compatible = "ti,k2g-evm", "ti,k2g", "ti-keystone" diff --git a/Documentation/devicetree/bindings/arm/armada-370-xp-pmsu.txt b/Documentation/devicetree/bindings/arm/marvell/armada-370-xp-pmsu.txt index 26799ef..26799ef 100644 --- a/Documentation/devicetree/bindings/arm/armada-370-xp-pmsu.txt +++ b/Documentation/devicetree/bindings/arm/marvell/armada-370-xp-pmsu.txt diff --git a/Documentation/devicetree/bindings/arm/armada-370-xp.txt b/Documentation/devicetree/bindings/arm/marvell/armada-370-xp.txt index c6ed90e..c6ed90e 100644 --- a/Documentation/devicetree/bindings/arm/armada-370-xp.txt +++ b/Documentation/devicetree/bindings/arm/marvell/armada-370-xp.txt diff --git a/Documentation/devicetree/bindings/arm/armada-375.txt b/Documentation/devicetree/bindings/arm/marvell/armada-375.txt index 867d0b8..867d0b8 100644 --- a/Documentation/devicetree/bindings/arm/armada-375.txt +++ b/Documentation/devicetree/bindings/arm/marvell/armada-375.txt diff --git a/Documentation/devicetree/bindings/arm/marvell/armada-37xx.txt b/Documentation/devicetree/bindings/arm/marvell/armada-37xx.txt new file mode 100644 index 0000000..51336e5 --- /dev/null +++ b/Documentation/devicetree/bindings/arm/marvell/armada-37xx.txt @@ -0,0 +1,16 @@ +Marvell Armada 37xx Platforms Device Tree Bindings +-------------------------------------------------- + +Boards using a SoC of the Marvell Armada 37xx family must carry the +following root node property: + + - compatible: must contain "marvell,armada3710" + +In addition, boards using the Marvell Armada 3720 SoC shall have the +following property before the previous one: + + - compatible: must contain "marvell,armada3720" + +Example: + +compatible = "marvell,armada-3720-db", "marvell,armada3720", "marvell,armada3710"; diff --git a/Documentation/devicetree/bindings/arm/armada-380-mpcore-soc-ctrl.txt b/Documentation/devicetree/bindings/arm/marvell/armada-380-mpcore-soc-ctrl.txt index 8781073..8781073 100644 --- a/Documentation/devicetree/bindings/arm/armada-380-mpcore-soc-ctrl.txt +++ b/Documentation/devicetree/bindings/arm/marvell/armada-380-mpcore-soc-ctrl.txt diff --git a/Documentation/devicetree/bindings/arm/armada-38x.txt b/Documentation/devicetree/bindings/arm/marvell/armada-38x.txt index 202953f..202953f 100644 --- a/Documentation/devicetree/bindings/arm/armada-38x.txt +++ b/Documentation/devicetree/bindings/arm/marvell/armada-38x.txt diff --git a/Documentation/devicetree/bindings/arm/armada-39x.txt b/Documentation/devicetree/bindings/arm/marvell/armada-39x.txt index 53d4ff9..53d4ff9 100644 --- a/Documentation/devicetree/bindings/arm/armada-39x.txt +++ b/Documentation/devicetree/bindings/arm/marvell/armada-39x.txt diff --git a/Documentation/devicetree/bindings/arm/marvell/armada-7k-8k.txt b/Documentation/devicetree/bindings/arm/marvell/armada-7k-8k.txt new file mode 100644 index 0000000..df98a9c --- /dev/null +++ b/Documentation/devicetree/bindings/arm/marvell/armada-7k-8k.txt @@ -0,0 +1,24 @@ +Marvell Armada 7K/8K Platforms Device Tree Bindings +--------------------------------------------------- + +Boards using a SoC of the Marvell Armada 7K or 8K families must carry +the following root node property: + + - compatible, with one of the following values: + + - "marvell,armada7020", "marvell,armada-ap806-dual", "marvell,armada-ap806" + when the SoC being used is the Armada 7020 + + - "marvell,armada7040", "marvell,armada-ap806-quad", "marvell,armada-ap806" + when the SoC being used is the Armada 7040 + + - "marvell,armada8020", "marvell,armada-ap806-dual", "marvell,armada-ap806" + when the SoC being used is the Armada 8020 + + - "marvell,armada8040", "marvell,armada-ap806-quad", "marvell,armada-ap806" + when the SoC being used is the Armada 8040 + +Example: + +compatible = "marvell,armada7040-db", "marvell,armada7040", + "marvell,armada-ap806-quad", "marvell,armada-ap806"; diff --git a/Documentation/devicetree/bindings/arm/armada-cpu-reset.txt b/Documentation/devicetree/bindings/arm/marvell/armada-cpu-reset.txt index b63a7b6..b63a7b6 100644 --- a/Documentation/devicetree/bindings/arm/armada-cpu-reset.txt +++ b/Documentation/devicetree/bindings/arm/marvell/armada-cpu-reset.txt diff --git a/Documentation/devicetree/bindings/arm/coherency-fabric.txt b/Documentation/devicetree/bindings/arm/marvell/coherency-fabric.txt index 9b5c3f6..9b5c3f6 100644 --- a/Documentation/devicetree/bindings/arm/coherency-fabric.txt +++ b/Documentation/devicetree/bindings/arm/marvell/coherency-fabric.txt diff --git a/Documentation/devicetree/bindings/arm/kirkwood.txt b/Documentation/devicetree/bindings/arm/marvell/kirkwood.txt index 98cce9a..98cce9a 100644 --- a/Documentation/devicetree/bindings/arm/kirkwood.txt +++ b/Documentation/devicetree/bindings/arm/marvell/kirkwood.txt diff --git a/Documentation/devicetree/bindings/arm/marvell,berlin.txt b/Documentation/devicetree/bindings/arm/marvell/marvell,berlin.txt index 3bab184..3bab184 100644 --- a/Documentation/devicetree/bindings/arm/marvell,berlin.txt +++ b/Documentation/devicetree/bindings/arm/marvell/marvell,berlin.txt diff --git a/Documentation/devicetree/bindings/arm/marvell,dove.txt b/Documentation/devicetree/bindings/arm/marvell/marvell,dove.txt index aaaf64c..aaaf64c 100644 --- a/Documentation/devicetree/bindings/arm/marvell,dove.txt +++ b/Documentation/devicetree/bindings/arm/marvell/marvell,dove.txt diff --git a/Documentation/devicetree/bindings/arm/marvell,kirkwood.txt b/Documentation/devicetree/bindings/arm/marvell/marvell,kirkwood.txt index ab0c9cd..7d28fe4 100644 --- a/Documentation/devicetree/bindings/arm/marvell,kirkwood.txt +++ b/Documentation/devicetree/bindings/arm/marvell/marvell,kirkwood.txt @@ -19,9 +19,12 @@ SoC. Currently known SoC compatibles are: And in addition, the compatible shall be extended with the specific board. Currently known boards are: +"buffalo,linkstation-lsqvl" +"buffalo,linkstation-lsvl" +"buffalo,linkstation-lswsxl" +"buffalo,linkstation-lswxl" +"buffalo,linkstation-lswvl" "buffalo,lschlv2" -"buffalo,lswvl" -"buffalo,lswxl" "buffalo,lsxhl" "buffalo,lsxl" "cloudengines,pogo02" diff --git a/Documentation/devicetree/bindings/arm/mvebu-cpu-config.txt b/Documentation/devicetree/bindings/arm/marvell/mvebu-cpu-config.txt index 2cdcd71..2cdcd71 100644 --- a/Documentation/devicetree/bindings/arm/mvebu-cpu-config.txt +++ b/Documentation/devicetree/bindings/arm/marvell/mvebu-cpu-config.txt diff --git a/Documentation/devicetree/bindings/arm/mvebu-system-controller.txt b/Documentation/devicetree/bindings/arm/marvell/mvebu-system-controller.txt index d24ab2e..d24ab2e 100644 --- a/Documentation/devicetree/bindings/arm/mvebu-system-controller.txt +++ b/Documentation/devicetree/bindings/arm/marvell/mvebu-system-controller.txt diff --git a/Documentation/devicetree/bindings/arm/mediatek.txt b/Documentation/devicetree/bindings/arm/mediatek.txt index 54f43bc..d9c2a37 100644 --- a/Documentation/devicetree/bindings/arm/mediatek.txt +++ b/Documentation/devicetree/bindings/arm/mediatek.txt @@ -11,6 +11,7 @@ compatible: Must contain one of "mediatek,mt6589" "mediatek,mt6592" "mediatek,mt6795" + "mediatek,mt7623" "mediatek,mt8127" "mediatek,mt8135" "mediatek,mt8173" @@ -33,6 +34,9 @@ Supported boards: - Evaluation board for MT6795(Helio X10): Required root node properties: - compatible = "mediatek,mt6795-evb", "mediatek,mt6795"; +- Evaluation board for MT7623: + Required root node properties: + - compatible = "mediatek,mt7623-evb", "mediatek,mt7623"; - MTK mt8127 tablet moose EVB: Required root node properties: - compatible = "mediatek,mt8127-moose", "mediatek,mt8127"; diff --git a/Documentation/devicetree/bindings/arm/lpc32xx.txt b/Documentation/devicetree/bindings/arm/nxp/lpc32xx.txt index 56ec8dd..56ec8dd 100644 --- a/Documentation/devicetree/bindings/arm/lpc32xx.txt +++ b/Documentation/devicetree/bindings/arm/nxp/lpc32xx.txt diff --git a/Documentation/devicetree/bindings/arm/omap/omap.txt b/Documentation/devicetree/bindings/arm/omap/omap.txt index a2bd593..21e71a5 100644 --- a/Documentation/devicetree/bindings/arm/omap/omap.txt +++ b/Documentation/devicetree/bindings/arm/omap/omap.txt @@ -23,6 +23,7 @@ Optional properties: during suspend. - ti,no-reset-on-init: When present, the module should not be reset at init - ti,no-idle-on-init: When present, the module should not be idled at init +- ti,no-idle: When present, the module is never allowed to idle. Example: @@ -154,7 +155,7 @@ Boards: compatible = "compulab,am437x-sbc-t43", "compulab,am437x-cm-t43", "ti,am4372", "ti,am43" - AM43x EPOS EVM - compatible = "ti,am43x-epos-evm", "ti,am4372", "ti,am43" + compatible = "ti,am43x-epos-evm", "ti,am43", "ti,am438x" - AM437x GP EVM compatible = "ti,am437x-gp-evm", "ti,am4372", "ti,am43" diff --git a/Documentation/devicetree/bindings/arm/pmu.txt b/Documentation/devicetree/bindings/arm/pmu.txt index 5651883..6eb73be 100644 --- a/Documentation/devicetree/bindings/arm/pmu.txt +++ b/Documentation/devicetree/bindings/arm/pmu.txt @@ -25,6 +25,7 @@ Required properties: "qcom,scorpion-pmu" "qcom,scorpion-mp-pmu" "qcom,krait-pmu" + "cavium,thunder-pmu" - interrupts : 1 combined interrupt or 1 per core. If the interrupt is a per-cpu interrupt (PPI) then 1 interrupt should be specified. @@ -46,6 +47,16 @@ Optional properties: - qcom,no-pc-write : Indicates that this PMU doesn't support the 0xc and 0xd events. +- secure-reg-access : Indicates that the ARMv7 Secure Debug Enable Register + (SDER) is accessible. This will cause the driver to do + any setup required that is only possible in ARMv7 secure + state. If not present the ARMv7 SDER will not be touched, + which means the PMU may fail to operate unless external + code (bootloader or security monitor) has performed the + appropriate initialisation. Note that this property is + not valid for non-ARMv7 CPUs or ARMv7 CPUs booting Linux + in Non-secure state. + Example: pmu { diff --git a/Documentation/devicetree/bindings/arm/qcom.txt b/Documentation/devicetree/bindings/arm/qcom.txt new file mode 100644 index 0000000..3e24518 --- /dev/null +++ b/Documentation/devicetree/bindings/arm/qcom.txt @@ -0,0 +1,51 @@ +QCOM device tree bindings +------------------------- + +Some qcom based bootloaders identify the dtb blob based on a set of +device properties like SoC and platform and revisions of those components. +To support this scheme, we encode this information into the board compatible +string. + +Each board must specify a top-level board compatible string with the following +format: + + compatible = "qcom,<SoC>[-<soc_version>][-<foundry_id>]-<board>[/<subtype>][-<board_version>]" + +The 'SoC' and 'board' elements are required. All other elements are optional. + +The 'SoC' element must be one of the following strings: + + apq8016 + apq8074 + apq8084 + apq8096 + msm8916 + msm8974 + msm8996 + +The 'board' element must be one of the following strings: + + cdp + liquid + dragonboard + mtp + sbc + +The 'soc_version' and 'board_version' elements take the form of v<Major>.<Minor> +where the minor number may be omitted when it's zero, i.e. v1.0 is the same +as v1. If all versions of the 'board_version' elements match, then a +wildcard '*' should be used, e.g. 'v*'. + +The 'foundry_id' and 'subtype' elements are one or more digits from 0 to 9. + +Examples: + + "qcom,msm8916-v1-cdp-pm8916-v2.1" + +A CDP board with an msm8916 SoC, version 1 paired with a pm8916 PMIC of version +2.1. + + "qcom,apq8074-v2.0-2-dragonboard/1-v0.1" + +A dragonboard board v0.1 of subtype 1 with an apq8074 SoC version 2, made in +foundry 2. diff --git a/Documentation/devicetree/bindings/arm/sunxi.txt b/Documentation/devicetree/bindings/arm/sunxi.txt index bb9b0faa..7e79fcc 100644 --- a/Documentation/devicetree/bindings/arm/sunxi.txt +++ b/Documentation/devicetree/bindings/arm/sunxi.txt @@ -11,5 +11,6 @@ using one of the following compatible strings: allwinner,sun7i-a20 allwinner,sun8i-a23 allwinner,sun8i-a33 + allwinner,sun8i-a83t allwinner,sun8i-h3 allwinner,sun9i-a80 diff --git a/Documentation/devicetree/bindings/ata/ahci-platform.txt b/Documentation/devicetree/bindings/ata/ahci-platform.txt index c2340ee..87adfb2 100644 --- a/Documentation/devicetree/bindings/ata/ahci-platform.txt +++ b/Documentation/devicetree/bindings/ata/ahci-platform.txt @@ -11,8 +11,10 @@ Required properties: - compatible : compatible string, one of: - "allwinner,sun4i-a10-ahci" - "hisilicon,hisi-ahci" + - "cavium,octeon-7130-ahci" - "ibm,476gtr-ahci" - "marvell,armada-380-ahci" + - "marvell,armada-3700-ahci" - "snps,dwc-ahci" - "snps,exynos5440-ahci" - "snps,spear-ahci" @@ -30,6 +32,10 @@ Optional properties: - target-supply : regulator for SATA target power - phys : reference to the SATA PHY node - phy-names : must be "sata-phy" +- ports-implemented : Mask that indicates which ports that the HBA supports + are available for software to use. Useful if PORTS_IMPL + is not programmed by the BIOS, which is true with + some embedded SOC's. Required properties when using sub-nodes: - #address-cells : number of cells to encode an address diff --git a/Documentation/devicetree/bindings/bus/ti-gpmc.txt b/Documentation/devicetree/bindings/bus/ti-gpmc.txt index 704be93..0168370 100644 --- a/Documentation/devicetree/bindings/bus/ti-gpmc.txt +++ b/Documentation/devicetree/bindings/bus/ti-gpmc.txt @@ -46,6 +46,9 @@ Timing properties for child nodes. All are optional and default to 0. - gpmc,adv-on-ns: Assertion time - gpmc,adv-rd-off-ns: Read deassertion time - gpmc,adv-wr-off-ns: Write deassertion time + - gpmc,adv-aad-mux-on-ns: Assertion time for AAD + - gpmc,adv-aad-mux-rd-off-ns: Read deassertion time for AAD + - gpmc,adv-aad-mux-wr-off-ns: Write deassertion time for AAD WE signals timings (in nanoseconds) corresponding to GPMC_CONFIG4: - gpmc,we-on-ns Assertion time @@ -54,6 +57,8 @@ Timing properties for child nodes. All are optional and default to 0. OE signals timings (in nanoseconds) corresponding to GPMC_CONFIG4: - gpmc,oe-on-ns: Assertion time - gpmc,oe-off-ns: Deassertion time + - gpmc,oe-aad-mux-on-ns: Assertion time for AAD + - gpmc,oe-aad-mux-off-ns: Deassertion time for AAD Access time and cycle time timings (in nanoseconds) corresponding to GPMC_CONFIG5: diff --git a/Documentation/devicetree/bindings/clock/axi-clkgen.txt b/Documentation/devicetree/bindings/clock/axi-clkgen.txt index 20e1704..fb40da3 100644 --- a/Documentation/devicetree/bindings/clock/axi-clkgen.txt +++ b/Documentation/devicetree/bindings/clock/axi-clkgen.txt @@ -8,7 +8,10 @@ Required properties: - compatible : shall be "adi,axi-clkgen-1.00.a" or "adi,axi-clkgen-2.00.a". - #clock-cells : from common clock binding; Should always be set to 0. - reg : Address and length of the axi-clkgen register set. -- clocks : Phandle and clock specifier for the parent clock. +- clocks : Phandle and clock specifier for the parent clock(s). This must + either reference one clock if only the first clock input is connected or two + if both clock inputs are connected. For the later case the clock connected + to the first input must be specified first. Optional properties: - clock-output-names : From common clock binding. diff --git a/Documentation/devicetree/bindings/clock/brcm,iproc-clocks.txt b/Documentation/devicetree/bindings/clock/brcm,iproc-clocks.txt index 0b35e71..6f66e9a 100644 --- a/Documentation/devicetree/bindings/clock/brcm,iproc-clocks.txt +++ b/Documentation/devicetree/bindings/clock/brcm,iproc-clocks.txt @@ -92,6 +92,7 @@ PLL and leaf clock compatible strings for Cygnus are: "brcm,cygnus-lcpll0" "brcm,cygnus-mipipll" "brcm,cygnus-asiu-clk" + "brcm,cygnus-audiopll" The following table defines the set of PLL/clock index and ID for Cygnus. These clock IDs are defined in: @@ -131,6 +132,11 @@ These clock IDs are defined in: ch4_unused mipipll 5 BCM_CYGNUS_MIPIPLL_CH4_UNUSED ch5_unused mipipll 6 BCM_CYGNUS_MIPIPLL_CH5_UNUSED + audiopll crystal 0 BCM_CYGNUS_AUDIOPLL + ch0_audio audiopll 1 BCM_CYGNUS_AUDIOPLL_CH0 + ch1_audio audiopll 2 BCM_CYGNUS_AUDIOPLL_CH1 + ch2_audio audiopll 3 BCM_CYGNUS_AUDIOPLL_CH2 + Northstar and Northstar Plus ------ PLL and leaf clock compatible strings for Northstar and Northstar Plus are: diff --git a/Documentation/devicetree/bindings/clock/lpc1850-creg-clk.txt b/Documentation/devicetree/bindings/clock/lpc1850-creg-clk.txt new file mode 100644 index 0000000..6f1c7b4 --- /dev/null +++ b/Documentation/devicetree/bindings/clock/lpc1850-creg-clk.txt @@ -0,0 +1,52 @@ +* NXP LPC1850 CREG clocks + +The NXP LPC18xx/43xx CREG (Configuration Registers) block contains +control registers for two low speed clocks. One of the clocks is a +32 kHz oscillator driver with power up/down and clock gating. Next +is a fixed divider that creates a 1 kHz clock from the 32 kHz osc. + +These clocks are used by the RTC and the Event Router peripherials. +The 32 kHz can also be routed to other peripherials to enable low +power modes. + +This binding uses the common clock binding: + Documentation/devicetree/bindings/clock/clock-bindings.txt + +Required properties: +- compatible: + Should be "nxp,lpc1850-creg-clk" +- #clock-cells: + Shall have value <1>. +- clocks: + Shall contain a phandle to the fixed 32 kHz crystal. + +The creg-clk node must be a child of the creg syscon node. + +The following clocks are available from the clock node. + +Clock ID Name + 0 1 kHz clock + 1 32 kHz Oscillator + +Example: +soc { + creg: syscon@40043000 { + compatible = "nxp,lpc1850-creg", "syscon", "simple-mfd"; + reg = <0x40043000 0x1000>; + + creg_clk: clock-controller { + compatible = "nxp,lpc1850-creg-clk"; + clocks = <&xtal32>; + #clock-cells = <1>; + }; + + ... + }; + + rtc: rtc@40046000 { + ... + clocks = <&creg_clk 0>, <&ccu1 CLK_CPU_BUS>; + clock-names = "rtc", "reg"; + ... + }; +}; diff --git a/Documentation/devicetree/bindings/clock/qca,ath79-pll.txt b/Documentation/devicetree/bindings/clock/qca,ath79-pll.txt index e0fc2c1..241fb05 100644 --- a/Documentation/devicetree/bindings/clock/qca,ath79-pll.txt +++ b/Documentation/devicetree/bindings/clock/qca,ath79-pll.txt @@ -3,7 +3,7 @@ Binding for Qualcomm Atheros AR7xxx/AR9XXX PLL controller The PPL controller provides the 3 main clocks of the SoC: CPU, DDR and AHB. Required Properties: -- compatible: has to be "qca,<soctype>-cpu-intc" and one of the following +- compatible: has to be "qca,<soctype>-pll" and one of the following fallbacks: - "qca,ar7100-pll" - "qca,ar7240-pll" @@ -21,8 +21,8 @@ Optional properties: Example: - memory-controller@18050000 { - compatible = "qca,ar9132-ppl", "qca,ar9130-pll"; + pll-controller@18050000 { + compatible = "qca,ar9132-pll", "qca,ar9130-pll"; reg = <0x18050000 0x20>; clock-names = "ref"; diff --git a/Documentation/devicetree/bindings/clock/qcom,gcc.txt b/Documentation/devicetree/bindings/clock/qcom,gcc.txt index 72f82f4..9a60fde 100644 --- a/Documentation/devicetree/bindings/clock/qcom,gcc.txt +++ b/Documentation/devicetree/bindings/clock/qcom,gcc.txt @@ -7,6 +7,7 @@ Required properties : "qcom,gcc-apq8064" "qcom,gcc-apq8084" "qcom,gcc-ipq8064" + "qcom,gcc-ipq4019" "qcom,gcc-msm8660" "qcom,gcc-msm8916" "qcom,gcc-msm8960" diff --git a/Documentation/devicetree/bindings/clock/renesas,cpg-mssr.txt b/Documentation/devicetree/bindings/clock/renesas,cpg-mssr.txt index 59297d3..fefb802 100644 --- a/Documentation/devicetree/bindings/clock/renesas,cpg-mssr.txt +++ b/Documentation/devicetree/bindings/clock/renesas,cpg-mssr.txt @@ -61,7 +61,7 @@ Examples reg = <0 0xe6e88000 0 64>; interrupts = <GIC_SPI 164 IRQ_TYPE_LEVEL_HIGH>; clocks = <&cpg CPG_MOD 310>; - clock-names = "sci_ick"; + clock-names = "fck"; dmas = <&dmac1 0x13>, <&dmac1 0x12>; dma-names = "tx", "rx"; power-domains = <&cpg>; diff --git a/Documentation/devicetree/bindings/clock/sunxi.txt b/Documentation/devicetree/bindings/clock/sunxi.txt index e59f57b..834436f 100644 --- a/Documentation/devicetree/bindings/clock/sunxi.txt +++ b/Documentation/devicetree/bindings/clock/sunxi.txt @@ -18,6 +18,7 @@ Required properties: "allwinner,sun4i-a10-cpu-clk" - for the CPU multiplexer clock "allwinner,sun4i-a10-axi-clk" - for the AXI clock "allwinner,sun8i-a23-axi-clk" - for the AXI clock on A23 + "allwinner,sun4i-a10-gates-clk" - for generic gates on all compatible SoCs "allwinner,sun4i-a10-axi-gates-clk" - for the AXI gates "allwinner,sun4i-a10-ahb-clk" - for the AHB clock "allwinner,sun5i-a13-ahb-clk" - for the AHB clock on A13 @@ -39,12 +40,14 @@ Required properties: "allwinner,sun6i-a31-apb0-clk" - for the APB0 clock on A31 "allwinner,sun8i-a23-apb0-clk" - for the APB0 clock on A23 "allwinner,sun9i-a80-apb0-clk" - for the APB0 bus clock on A80 + "allwinner,sun8i-a83t-apb0-gates-clk" - for the APB0 gates on A83T "allwinner,sun4i-a10-apb0-gates-clk" - for the APB0 gates on A10 "allwinner,sun5i-a13-apb0-gates-clk" - for the APB0 gates on A13 "allwinner,sun5i-a10s-apb0-gates-clk" - for the APB0 gates on A10s "allwinner,sun6i-a31-apb0-gates-clk" - for the APB0 gates on A31 "allwinner,sun7i-a20-apb0-gates-clk" - for the APB0 gates on A20 "allwinner,sun8i-a23-apb0-gates-clk" - for the APB0 gates on A23 + "allwinner,sun8i-h3-apb0-gates-clk" - for the APB0 gates on H3 "allwinner,sun9i-a80-apb0-gates-clk" - for the APB0 gates on A80 "allwinner,sun4i-a10-apb1-clk" - for the APB1 clock "allwinner,sun9i-a80-apb1-clk" - for the APB1 bus clock on A80 @@ -57,6 +60,7 @@ Required properties: "allwinner,sun9i-a80-apb1-gates-clk" - for the APB1 gates on A80 "allwinner,sun6i-a31-apb2-gates-clk" - for the APB2 gates on A31 "allwinner,sun8i-a23-apb2-gates-clk" - for the APB2 gates on A23 + "allwinner,sun8i-a83t-bus-gates-clk" - for the bus gates on A83T "allwinner,sun8i-h3-bus-gates-clk" - for the bus gates on H3 "allwinner,sun9i-a80-apbs-gates-clk" - for the APBS gates on A80 "allwinner,sun4i-a10-dram-gates-clk" - for the DRAM gates on A10 diff --git a/Documentation/devicetree/bindings/clock/ti/adpll.txt b/Documentation/devicetree/bindings/clock/ti/adpll.txt new file mode 100644 index 0000000..4c8a2ce --- /dev/null +++ b/Documentation/devicetree/bindings/clock/ti/adpll.txt @@ -0,0 +1,41 @@ +Binding for Texas Instruments ADPLL clock. + +Binding status: Unstable - ABI compatibility may be broken in the future + +This binding uses the common clock binding[1]. It assumes a +register-mapped ADPLL with two to three selectable input clocks +and three to four children. + +[1] Documentation/devicetree/bindings/clock/clock-bindings.txt + +Required properties: +- compatible : shall be one of "ti,dm814-adpll-s-clock" or + "ti,dm814-adpll-lj-clock" depending on the type of the ADPLL +- #clock-cells : from common clock binding; shall be set to 1. +- clocks : link phandles of parent clocks clkinp and clkinpulow, note + that the adpll-s-clock also has an optional clkinphif +- reg : address and length of the register set for controlling the ADPLL. + +Examples: + adpll_mpu_ck: adpll@40 { + #clock-cells = <1>; + compatible = "ti,dm814-adpll-s-clock"; + reg = <0x40 0x40>; + clocks = <&devosc_ck &devosc_ck &devosc_ck>; + clock-names = "clkinp", "clkinpulow", "clkinphif"; + clock-output-names = "481c5040.adpll.dcoclkldo", + "481c5040.adpll.clkout", + "481c5040.adpll.clkoutx2", + "481c5040.adpll.clkouthif"; + }; + + adpll_dsp_ck: adpll@80 { + #clock-cells = <1>; + compatible = "ti,dm814-adpll-lj-clock"; + reg = <0x80 0x30>; + clocks = <&devosc_ck &devosc_ck>; + clock-names = "clkinp", "clkinpulow"; + clock-output-names = "481c5080.adpll.dcoclkldo", + "481c5080.adpll.clkout", + "481c5080.adpll.clkoutldo"; + }; diff --git a/Documentation/devicetree/bindings/clock/xgene.txt b/Documentation/devicetree/bindings/clock/xgene.txt index 1c4ef77..82f9638 100644 --- a/Documentation/devicetree/bindings/clock/xgene.txt +++ b/Documentation/devicetree/bindings/clock/xgene.txt @@ -9,6 +9,8 @@ Required properties: "apm,xgene-socpll-clock" - for a X-Gene SoC PLL clock "apm,xgene-pcppll-clock" - for a X-Gene PCP PLL clock "apm,xgene-device-clock" - for a X-Gene device clock + "apm,xgene-socpll-v2-clock" - for a X-Gene SoC PLL v2 clock + "apm,xgene-pcppll-v2-clock" - for a X-Gene PCP PLL v2 clock Required properties for SoC or PCP PLL clocks: - reg : shall be the physical PLL register address for the pll clock. diff --git a/Documentation/devicetree/bindings/display/arm,hdlcd.txt b/Documentation/devicetree/bindings/display/arm,hdlcd.txt new file mode 100644 index 0000000..78bc242 --- /dev/null +++ b/Documentation/devicetree/bindings/display/arm,hdlcd.txt @@ -0,0 +1,79 @@ +ARM HDLCD + +This is a display controller found on several development platforms produced +by ARM Ltd and in more modern of its' Fast Models. The HDLCD is an RGB +streamer that reads the data from a framebuffer and sends it to a single +digital encoder (DVI or HDMI). + +Required properties: + - compatible: "arm,hdlcd" + - reg: Physical base address and length of the controller's registers. + - interrupts: One interrupt used by the display controller to notify the + interrupt controller when any of the interrupt sources programmed in + the interrupt mask register have activated. + - clocks: A list of phandle + clock-specifier pairs, one for each + entry in 'clock-names'. + - clock-names: A list of clock names. For HDLCD it should contain: + - "pxlclk" for the clock feeding the output PLL of the controller. + +Required sub-nodes: + - port: The HDLCD connection to an encoder chip. The connection is modeled + using the OF graph bindings specified in + Documentation/devicetree/bindings/graph.txt. + +Optional properties: + - memory-region: phandle to a node describing memory (see + Documentation/devicetree/bindings/reserved-memory/reserved-memory.txt) to be + used for the framebuffer; if not present, the framebuffer may be located + anywhere in memory. + + +Example: + +/ { + ... + + hdlcd@2b000000 { + compatible = "arm,hdlcd"; + reg = <0 0x2b000000 0 0x1000>; + interrupts = <GIC_SPI 85 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&oscclk5>; + clock-names = "pxlclk"; + port { + hdlcd_output: endpoint@0 { + remote-endpoint = <&hdmi_enc_input>; + }; + }; + }; + + /* HDMI encoder on I2C bus */ + i2c@7ffa0000 { + .... + hdmi-transmitter@70 { + compatible = "....."; + reg = <0x70>; + port@0 { + hdmi_enc_input: endpoint { + remote-endpoint = <&hdlcd_output>; + }; + + hdmi_enc_output: endpoint { + remote-endpoint = <&hdmi_1_port>; + }; + }; + }; + + }; + + hdmi1: connector@1 { + compatible = "hdmi-connector"; + type = "a"; + port { + hdmi_1_port: endpoint { + remote-endpoint = <&hdmi_enc_output>; + }; + }; + }; + + ... +}; diff --git a/Documentation/devicetree/bindings/display/brcm,bcm-vc4.txt b/Documentation/devicetree/bindings/display/brcm,bcm-vc4.txt index 56a961a..9f97df4 100644 --- a/Documentation/devicetree/bindings/display/brcm,bcm-vc4.txt +++ b/Documentation/devicetree/bindings/display/brcm,bcm-vc4.txt @@ -35,6 +35,12 @@ Optional properties for HDMI: as an interrupt/status bit in the HDMI controller itself). See bindings/pinctrl/brcm,bcm2835-gpio.txt +Required properties for V3D: +- compatible: Should be "brcm,bcm2835-v3d" +- reg: Physical base address and length of the V3D's registers +- interrupts: The interrupt number + See bindings/interrupt-controller/brcm,bcm2835-armctrl-ic.txt + Example: pixelvalve@7e807000 { compatible = "brcm,bcm2835-pixelvalve2"; @@ -60,6 +66,12 @@ hdmi: hdmi@7e902000 { clock-names = "pixel", "hdmi"; }; +v3d: v3d@7ec00000 { + compatible = "brcm,bcm2835-v3d"; + reg = <0x7ec00000 0x1000>; + interrupts = <1 10>; +}; + vc4: gpu { compatible = "brcm,bcm2835-vc4"; }; diff --git a/Documentation/devicetree/bindings/display/exynos/exynos_dsim.txt b/Documentation/devicetree/bindings/display/exynos/exynos_dsim.txt index 0e6f0c0..22756b3 100644 --- a/Documentation/devicetree/bindings/display/exynos/exynos_dsim.txt +++ b/Documentation/devicetree/bindings/display/exynos/exynos_dsim.txt @@ -6,6 +6,7 @@ Required properties: "samsung,exynos4210-mipi-dsi" /* for Exynos4 SoCs */ "samsung,exynos4415-mipi-dsi" /* for Exynos4415 SoC */ "samsung,exynos5410-mipi-dsi" /* for Exynos5410/5420/5440 SoCs */ + "samsung,exynos5422-mipi-dsi" /* for Exynos5422/5800 SoCs */ "samsung,exynos5433-mipi-dsi" /* for Exynos5433 SoCs */ - reg: physical base address and length of the registers set for the device - interrupts: should contain DSI interrupt diff --git a/Documentation/devicetree/bindings/display/exynos/samsung-fimd.txt b/Documentation/devicetree/bindings/display/exynos/samsung-fimd.txt index 27c3ce0..c7c6b9a 100644 --- a/Documentation/devicetree/bindings/display/exynos/samsung-fimd.txt +++ b/Documentation/devicetree/bindings/display/exynos/samsung-fimd.txt @@ -12,7 +12,8 @@ Required properties: "samsung,exynos3250-fimd"; /* for Exynos3250/3472 SoCs */ "samsung,exynos4210-fimd"; /* for Exynos4 SoCs */ "samsung,exynos4415-fimd"; /* for Exynos4415 SoC */ - "samsung,exynos5250-fimd"; /* for Exynos5 SoCs */ + "samsung,exynos5250-fimd"; /* for Exynos5250 SoCs */ + "samsung,exynos5420-fimd"; /* for Exynos5420/5422/5800 SoCs */ - reg: physical base address and length of the FIMD registers set. diff --git a/Documentation/devicetree/bindings/display/msm/dsi.txt b/Documentation/devicetree/bindings/display/msm/dsi.txt index e7423be..f5948c4 100644 --- a/Documentation/devicetree/bindings/display/msm/dsi.txt +++ b/Documentation/devicetree/bindings/display/msm/dsi.txt @@ -44,9 +44,34 @@ Optional properties: - pinctrl-names: the pin control state names; should contain "default" - pinctrl-0: the default pinctrl state (active) - pinctrl-n: the "sleep" pinctrl state -- port: DSI controller output port. This contains one endpoint subnode, with its - remote-endpoint set to the phandle of the connected panel's endpoint. - See Documentation/devicetree/bindings/graph.txt for device graph info. +- port: DSI controller output port, containing one endpoint subnode. + + DSI Endpoint properties: + - remote-endpoint: set to phandle of the connected panel's endpoint. + See Documentation/devicetree/bindings/graph.txt for device graph info. + - qcom,data-lane-map: this describes how the logical DSI lanes are mapped + to the physical lanes on the given platform. The value contained in + index n describes what logical data lane is mapped to the physical data + lane n (DATAn, where n lies between 0 and 3). + + For example: + + qcom,data-lane-map = <3 0 1 2>; + + The above mapping describes that the logical data lane DATA3 is mapped to + the physical data lane DATA0, logical DATA0 to physical DATA1, logic DATA1 + to phys DATA2 and logic DATA2 to phys DATA3. + + There are only a limited number of physical to logical mappings possible: + + "0123": Logic 0->Phys 0; Logic 1->Phys 1; Logic 2->Phys 2; Logic 3->Phys 3; + "3012": Logic 3->Phys 0; Logic 0->Phys 1; Logic 1->Phys 2; Logic 2->Phys 3; + "2301": Logic 2->Phys 0; Logic 3->Phys 1; Logic 0->Phys 2; Logic 1->Phys 3; + "1230": Logic 1->Phys 0; Logic 2->Phys 1; Logic 3->Phys 2; Logic 0->Phys 3; + "0321": Logic 0->Phys 0; Logic 3->Phys 1; Logic 2->Phys 2; Logic 1->Phys 3; + "1032": Logic 1->Phys 0; Logic 0->Phys 1; Logic 3->Phys 2; Logic 2->Phys 3; + "2103": Logic 2->Phys 0; Logic 1->Phys 1; Logic 0->Phys 2; Logic 3->Phys 3; + "3210": Logic 3->Phys 0; Logic 2->Phys 1; Logic 1->Phys 2; Logic 0->Phys 3; DSI PHY: Required properties: @@ -131,6 +156,7 @@ Example: port { dsi0_out: endpoint { remote-endpoint = <&panel_in>; + lanes = <0 1 2 3>; }; }; }; diff --git a/Documentation/devicetree/bindings/display/msm/hdmi.txt b/Documentation/devicetree/bindings/display/msm/hdmi.txt index 379ee2e..b63f614 100644 --- a/Documentation/devicetree/bindings/display/msm/hdmi.txt +++ b/Documentation/devicetree/bindings/display/msm/hdmi.txt @@ -11,6 +11,7 @@ Required properties: - reg: Physical base address and length of the controller's registers - reg-names: "core_physical" - interrupts: The interrupt signal from the hdmi block. +- power-domains: Should be <&mmcc MDSS_GDSC>. - clocks: device clocks See ../clocks/clock-bindings.txt for details. - qcom,hdmi-tx-ddc-clk-gpio: ddc clk pin @@ -18,6 +19,8 @@ Required properties: - qcom,hdmi-tx-hpd-gpio: hpd pin - core-vdda-supply: phandle to supply regulator - hdmi-mux-supply: phandle to mux regulator +- phys: the phandle for the HDMI PHY device +- phy-names: the name of the corresponding PHY device Optional properties: - qcom,hdmi-tx-mux-en-gpio: hdmi mux enable pin @@ -27,15 +30,38 @@ Optional properties: - pinctrl-0: the default pinctrl state (active) - pinctrl-1: the "sleep" pinctrl state +HDMI PHY: +Required properties: +- compatible: Could be the following + * "qcom,hdmi-phy-8660" + * "qcom,hdmi-phy-8960" + * "qcom,hdmi-phy-8974" + * "qcom,hdmi-phy-8084" + * "qcom,hdmi-phy-8996" +- #phy-cells: Number of cells in a PHY specifier; Should be 0. +- reg: Physical base address and length of the registers of the PHY sub blocks. +- reg-names: The names of register regions. The following regions are required: + * "hdmi_phy" + * "hdmi_pll" + For HDMI PHY on msm8996, these additional register regions are required: + * "hdmi_tx_l0" + * "hdmi_tx_l1" + * "hdmi_tx_l3" + * "hdmi_tx_l4" +- power-domains: Should be <&mmcc MDSS_GDSC>. +- clocks: device clocks + See Documentation/devicetree/bindings/clocks/clock-bindings.txt for details. +- core-vdda-supply: phandle to vdda regulator device node + Example: / { ... - hdmi: qcom,hdmi-tx-8960@4a00000 { + hdmi: hdmi@4a00000 { compatible = "qcom,hdmi-tx-8960"; reg-names = "core_physical"; - reg = <0x04a00000 0x1000>; + reg = <0x04a00000 0x2f0>; interrupts = <GIC_SPI 79 0>; power-domains = <&mmcc MDSS_GDSC>; clock-names = @@ -54,5 +80,21 @@ Example: pinctrl-names = "default", "sleep"; pinctrl-0 = <&hpd_active &ddc_active &cec_active>; pinctrl-1 = <&hpd_suspend &ddc_suspend &cec_suspend>; + + phys = <&hdmi_phy>; + phy-names = "hdmi_phy"; + }; + + hdmi_phy: phy@4a00400 { + compatible = "qcom,hdmi-phy-8960"; + reg-names = "hdmi_phy", + "hdmi_pll"; + reg = <0x4a00400 0x60>, + <0x4a00500 0x100>; + #phy-cells = <0>; + power-domains = <&mmcc MDSS_GDSC>; + clock-names = "slave_iface_clk"; + clocks = <&mmcc HDMI_S_AHB_CLK>; + core-vdda-supply = <&pm8921_hdmi_mvs>; }; }; diff --git a/Documentation/devicetree/bindings/display/panel/lg,lp120up1.txt b/Documentation/devicetree/bindings/display/panel/lg,lp120up1.txt new file mode 100644 index 0000000..8c5de69 --- /dev/null +++ b/Documentation/devicetree/bindings/display/panel/lg,lp120up1.txt @@ -0,0 +1,7 @@ +LG 12.0" (1920x1280 pixels) TFT LCD panel + +Required properties: +- compatible: should be "lg,lp120up1" + +This binding is compatible with the simple-panel binding, which is specified +in simple-panel.txt in this directory. diff --git a/Documentation/devicetree/bindings/display/panel/urt,umsh-8596md.txt b/Documentation/devicetree/bindings/display/panel/urt,umsh-8596md.txt new file mode 100644 index 0000000..088a6ce --- /dev/null +++ b/Documentation/devicetree/bindings/display/panel/urt,umsh-8596md.txt @@ -0,0 +1,16 @@ +United Radiant Technology UMSH-8596MD-xT 7.0" WVGA TFT LCD panel + +Supported are LVDS versions (-11T, -19T) and parallel ones +(-T, -1T, -7T, -20T). + +Required properties: +- compatible: should be one of: + "urt,umsh-8596md-t", + "urt,umsh-8596md-1t", + "urt,umsh-8596md-7t", + "urt,umsh-8596md-11t", + "urt,umsh-8596md-19t", + "urt,umsh-8596md-20t". + +This binding is compatible with the simple-panel binding, which is specified +in simple-panel.txt in this directory. diff --git a/Documentation/devicetree/bindings/display/renesas,du.txt b/Documentation/devicetree/bindings/display/renesas,du.txt index eccd4f4..0d30e42 100644 --- a/Documentation/devicetree/bindings/display/renesas,du.txt +++ b/Documentation/devicetree/bindings/display/renesas,du.txt @@ -8,6 +8,7 @@ Required Properties: - "renesas,du-r8a7791" for R8A7791 (R-Car M2-W) compatible DU - "renesas,du-r8a7793" for R8A7793 (R-Car M2-N) compatible DU - "renesas,du-r8a7794" for R8A7794 (R-Car E2) compatible DU + - "renesas,du-r8a7795" for R8A7795 (R-Car H3) compatible DU - reg: A list of base address and length of each memory resource, one for each entry in the reg-names property. @@ -24,7 +25,7 @@ Required Properties: - clock-names: Name of the clocks. This property is model-dependent. - R8A7779 uses a single functional clock. The clock doesn't need to be named. - - R8A779[0134] use one functional clock per channel and one clock per LVDS + - R8A779[01345] use one functional clock per channel and one clock per LVDS encoder (if available). The functional clocks must be named "du.x" with "x" being the channel numerical index. The LVDS clocks must be named "lvds.x" with "x" being the LVDS encoder numerical index. @@ -41,13 +42,14 @@ bindings specified in Documentation/devicetree/bindings/graph.txt. The following table lists for each supported model the port number corresponding to each DU output. - Port 0 Port1 Port2 + Port 0 Port1 Port2 Port3 ----------------------------------------------------------------------------- - R8A7779 (H1) DPAD 0 DPAD 1 - - R8A7790 (H2) DPAD LVDS 0 LVDS 1 - R8A7791 (M2-W) DPAD LVDS 0 - - R8A7793 (M2-N) DPAD LVDS 0 - - R8A7794 (E2) DPAD 0 DPAD 1 - + R8A7779 (H1) DPAD 0 DPAD 1 - - + R8A7790 (H2) DPAD LVDS 0 LVDS 1 - + R8A7791 (M2-W) DPAD LVDS 0 - - + R8A7793 (M2-N) DPAD LVDS 0 - - + R8A7794 (E2) DPAD 0 DPAD 1 - - + R8A7795 (H3) DPAD HDMI 0 HDMI 1 LVDS Example: R8A7790 (R-Car H2) DU diff --git a/Documentation/devicetree/bindings/display/rockchip/inno_hdmi-rockchip.txt b/Documentation/devicetree/bindings/display/rockchip/inno_hdmi-rockchip.txt new file mode 100644 index 0000000..8096a29 --- /dev/null +++ b/Documentation/devicetree/bindings/display/rockchip/inno_hdmi-rockchip.txt @@ -0,0 +1,50 @@ +Rockchip specific extensions to the Innosilicon HDMI +================================ + +Required properties: +- compatible: + "rockchip,rk3036-inno-hdmi"; +- reg: + Physical base address and length of the controller's registers. +- clocks, clock-names: + Phandle to hdmi controller clock, name should be "pclk" +- interrupts: + HDMI interrupt number +- ports: + Contain one port node with endpoint definitions as defined in + Documentation/devicetree/bindings/graph.txt. +- pinctrl-0, pinctrl-name: + Switch the iomux of HPD/CEC pins to HDMI function. + +Example: +hdmi: hdmi@20034000 { + compatible = "rockchip,rk3036-inno-hdmi"; + reg = <0x20034000 0x4000>; + interrupts = <GIC_SPI 45 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&cru PCLK_HDMI>; + clock-names = "pclk"; + pinctrl-names = "default"; + pinctrl-0 = <&hdmi_ctl>; + status = "disabled"; + + hdmi_in: port { + #address-cells = <1>; + #size-cells = <0>; + hdmi_in_lcdc: endpoint@0 { + reg = <0>; + remote-endpoint = <&lcdc_out_hdmi>; + }; + }; +}; + +&pinctrl { + hdmi { + hdmi_ctl: hdmi-ctl { + rockchip,pins = <1 8 RK_FUNC_1 &pcfg_pull_none>, + <1 9 RK_FUNC_1 &pcfg_pull_none>, + <1 10 RK_FUNC_1 &pcfg_pull_none>, + <1 11 RK_FUNC_1 &pcfg_pull_none>; + }; + }; + +}; diff --git a/Documentation/devicetree/bindings/dma/arm-pl330.txt b/Documentation/devicetree/bindings/dma/arm-pl330.txt index 2675658..db7e226 100644 --- a/Documentation/devicetree/bindings/dma/arm-pl330.txt +++ b/Documentation/devicetree/bindings/dma/arm-pl330.txt @@ -15,6 +15,7 @@ Optional properties: cells in the dmas property of client device. - dma-channels: contains the total number of DMA channels supported by the DMAC - dma-requests: contains the total number of DMA requests supported by the DMAC + - arm,pl330-broken-no-flushp: quirk for avoiding to execute DMAFLUSHP Example: diff --git a/Documentation/devicetree/bindings/dma/mmp-dma.txt b/Documentation/devicetree/bindings/dma/mmp-dma.txt index 7a802f6..8f7364a 100644 --- a/Documentation/devicetree/bindings/dma/mmp-dma.txt +++ b/Documentation/devicetree/bindings/dma/mmp-dma.txt @@ -12,6 +12,8 @@ Required properties: Optional properties: - #dma-channels: Number of DMA channels supported by the controller (defaults to 32 when not specified) +- #dma-requests: Number of DMA requestor lines supported by the controller + (defaults to 32 when not specified) "marvell,pdma-1.0" Used platforms: pxa25x, pxa27x, pxa3xx, pxa93x, pxa168, pxa910, pxa688. diff --git a/Documentation/devicetree/bindings/dma/qcom_hidma_mgmt.txt b/Documentation/devicetree/bindings/dma/qcom_hidma_mgmt.txt new file mode 100644 index 0000000..fd5618b --- /dev/null +++ b/Documentation/devicetree/bindings/dma/qcom_hidma_mgmt.txt @@ -0,0 +1,89 @@ +Qualcomm Technologies HIDMA Management interface + +Qualcomm Technologies HIDMA is a high speed DMA device. It only supports +memcpy and memset capabilities. It has been designed for virtualized +environments. + +Each HIDMA HW instance consists of multiple DMA channels. These channels +share the same bandwidth. The bandwidth utilization can be parititioned +among channels based on the priority and weight assignments. + +There are only two priority levels and 15 weigh assignments possible. + +Other parameters here determine how much of the system bus this HIDMA +instance can use like maximum read/write request and and number of bytes to +read/write in a single burst. + +Main node required properties: +- compatible: "qcom,hidma-mgmt-1.0"; +- reg: Address range for DMA device +- dma-channels: Number of channels supported by this DMA controller. +- max-write-burst-bytes: Maximum write burst in bytes that HIDMA can + occupy the bus for in a single transaction. A memcpy requested is + fragmented to multiples of this amount. This parameter is used while + writing into destination memory. Setting this value incorrectly can + starve other peripherals in the system. +- max-read-burst-bytes: Maximum read burst in bytes that HIDMA can + occupy the bus for in a single transaction. A memcpy request is + fragmented to multiples of this amount. This parameter is used while + reading the source memory. Setting this value incorrectly can starve + other peripherals in the system. +- max-write-transactions: This value is how many times a write burst is + applied back to back while writing to the destination before yielding + the bus. +- max-read-transactions: This value is how many times a read burst is + applied back to back while reading the source before yielding the bus. +- channel-reset-timeout-cycles: Channel reset timeout in cycles for this SOC. + Once a reset is applied to the HW, HW starts a timer for reset operation + to confirm. If reset is not completed within this time, HW reports reset + failure. + +Sub-nodes: + +HIDMA has one or more DMA channels that are used to move data from one +memory location to another. + +When the OS is not in control of the management interface (i.e. it's a guest), +the channel nodes appear on their own, not under a management node. + +Required properties: +- compatible: must contain "qcom,hidma-1.0" +- reg: Addresses for the transfer and event channel +- interrupts: Should contain the event interrupt +- desc-count: Number of asynchronous requests this channel can handle +- iommus: required a iommu node + +Example: + +Hypervisor OS configuration: + + hidma-mgmt@f9984000 = { + compatible = "qcom,hidma-mgmt-1.0"; + reg = <0xf9984000 0x15000>; + dma-channels = <6>; + max-write-burst-bytes = <1024>; + max-read-burst-bytes = <1024>; + max-write-transactions = <31>; + max-read-transactions = <31>; + channel-reset-timeout-cycles = <0x500>; + + hidma_24: dma-controller@0x5c050000 { + compatible = "qcom,hidma-1.0"; + reg = <0 0x5c050000 0x0 0x1000>, + <0 0x5c0b0000 0x0 0x1000>; + interrupts = <0 389 0>; + desc-count = <10>; + iommus = <&system_mmu>; + }; + }; + +Guest OS configuration: + + hidma_24: dma-controller@0x5c050000 { + compatible = "qcom,hidma-1.0"; + reg = <0 0x5c050000 0x0 0x1000>, + <0 0x5c0b0000 0x0 0x1000>; + interrupts = <0 389 0>; + desc-count = <10>; + iommus = <&system_mmu>; + }; diff --git a/Documentation/devicetree/bindings/edac/apm-xgene-edac.txt b/Documentation/devicetree/bindings/edac/apm-xgene-edac.txt index 78e2a31..1006b04 100644 --- a/Documentation/devicetree/bindings/edac/apm-xgene-edac.txt +++ b/Documentation/devicetree/bindings/edac/apm-xgene-edac.txt @@ -16,6 +16,10 @@ Required properties: - regmap-mcba : Regmap of the MCB-A (memory bridge) resource. - regmap-mcbb : Regmap of the MCB-B (memory bridge) resource. - regmap-efuse : Regmap of the PMD efuse resource. +- regmap-rb : Regmap of the register bus resource. This property + is optional only for compatibility. If the RB + error conditions are not cleared, it will + continuously generate interrupt. - reg : First resource shall be the CPU bus (PCP) resource. - interrupts : Interrupt-specifier for MCU, PMD, L3, or SoC error IRQ(s). @@ -64,6 +68,11 @@ Example: reg = <0x0 0x1054a000 0x0 0x20>; }; + rb: rb@7e000000 { + compatible = "apm,xgene-rb", "syscon"; + reg = <0x0 0x7e000000 0x0 0x10>; + }; + edac@78800000 { compatible = "apm,xgene-edac"; #address-cells = <2>; @@ -73,6 +82,7 @@ Example: regmap-mcba = <&mcba>; regmap-mcbb = <&mcbb>; regmap-efuse = <&efuse>; + regmap-rb = <&rb>; reg = <0x0 0x78800000 0x0 0x100>; interrupts = <0x0 0x20 0x4>, <0x0 0x21 0x4>, diff --git a/Documentation/devicetree/bindings/goldfish/audio.txt b/Documentation/devicetree/bindings/goldfish/audio.txt new file mode 100644 index 0000000..d043fda --- /dev/null +++ b/Documentation/devicetree/bindings/goldfish/audio.txt @@ -0,0 +1,17 @@ +Android Goldfish Audio + +Android goldfish audio device generated by android emulator. + +Required properties: + +- compatible : should contain "google,goldfish-audio" to match emulator +- reg : <registers mapping> +- interrupts : <interrupt mapping> + +Example: + + goldfish_audio@9030000 { + compatible = "google,goldfish-audio"; + reg = <0x9030000 0x100>; + interrupts = <0x4>; + }; diff --git a/Documentation/devicetree/bindings/goldfish/battery.txt b/Documentation/devicetree/bindings/goldfish/battery.txt new file mode 100644 index 0000000..4fb6139 --- /dev/null +++ b/Documentation/devicetree/bindings/goldfish/battery.txt @@ -0,0 +1,17 @@ +Android Goldfish Battery + +Android goldfish battery device generated by android emulator. + +Required properties: + +- compatible : should contain "google,goldfish-battery" to match emulator +- reg : <registers mapping> +- interrupts : <interrupt mapping> + +Example: + + goldfish_battery@9020000 { + compatible = "google,goldfish-battery"; + reg = <0x9020000 0x1000>; + interrupts = <0x3>; + }; diff --git a/Documentation/devicetree/bindings/goldfish/events.txt b/Documentation/devicetree/bindings/goldfish/events.txt new file mode 100644 index 0000000..5babf46 --- /dev/null +++ b/Documentation/devicetree/bindings/goldfish/events.txt @@ -0,0 +1,17 @@ +Android Goldfish Events Keypad + +Android goldfish events keypad device generated by android emulator. + +Required properties: + +- compatible : should contain "google,goldfish-events-keypad" to match emulator +- reg : <registers mapping> +- interrupts : <interrupt mapping> + +Example: + + goldfish-events@9040000 { + compatible = "google,goldfish-events-keypad"; + reg = <0x9040000 0x1000>; + interrupts = <0x5>; + }; diff --git a/Documentation/devicetree/bindings/goldfish/pipe.txt b/Documentation/devicetree/bindings/goldfish/pipe.txt new file mode 100644 index 0000000..e417a31 --- /dev/null +++ b/Documentation/devicetree/bindings/goldfish/pipe.txt @@ -0,0 +1,17 @@ +Android Goldfish QEMU Pipe + +Andorid pipe virtual device generated by android emulator. + +Required properties: + +- compatible : should contain "google,android-pipe" to match emulator +- reg : <registers mapping> +- interrupts : <interrupt mapping> + +Example: + + android_pipe@a010000 { + compatible = "google,android-pipe"; + reg = <ff018000 0x2000>; + interrupts = <0x12>; + }; diff --git a/Documentation/devicetree/bindings/goldfish/tty.txt b/Documentation/devicetree/bindings/goldfish/tty.txt new file mode 100644 index 0000000..8264827 --- /dev/null +++ b/Documentation/devicetree/bindings/goldfish/tty.txt @@ -0,0 +1,17 @@ +Android Goldfish TTY + +Android goldfish tty device generated by android emulator. + +Required properties: + +- compatible : should contain "google,goldfish-tty" to match emulator +- reg : <registers mapping> +- interrupts : <interrupt mapping> + +Example: + + goldfish_tty@1f004000 { + compatible = "google,goldfish-tty"; + reg = <0x1f004000 0x1000>; + interrupts = <0xc>; + }; diff --git a/Documentation/devicetree/bindings/gpio/gpio-altera.txt b/Documentation/devicetree/bindings/gpio/gpio-altera.txt index 12f5014..826a720 100644 --- a/Documentation/devicetree/bindings/gpio/gpio-altera.txt +++ b/Documentation/devicetree/bindings/gpio/gpio-altera.txt @@ -12,7 +12,7 @@ Required properties: - #interrupt-cells : Should be 1. The interrupt type is fixed in the hardware. - The first cell is the GPIO offset number within the GPIO controller. - interrupts: Specify the interrupt. -- altr,interrupt-trigger: Specifies the interrupt trigger type the GPIO +- altr,interrupt-type: Specifies the interrupt trigger type the GPIO hardware is synthesized. This field is required if the Altera GPIO controller used has IRQ enabled as the interrupt type is not software controlled, but hardware synthesized. Required if GPIO is used as an interrupt @@ -35,7 +35,7 @@ gpio_altr: gpio@0xff200000 { reg = <0xff200000 0x10>; interrupts = <0 45 4>; altr,ngpio = <32>; - altr,interrupt-trigger = <IRQ_TYPE_EDGE_RISING>; + altr,interrupt-type = <IRQ_TYPE_EDGE_RISING>; #gpio-cells = <2>; gpio-controller; #interrupt-cells = <1>; diff --git a/Documentation/devicetree/bindings/gpio/gpio-mcp23s08.txt b/Documentation/devicetree/bindings/gpio/gpio-mcp23s08.txt index f3332b9..c934106 100644 --- a/Documentation/devicetree/bindings/gpio/gpio-mcp23s08.txt +++ b/Documentation/devicetree/bindings/gpio/gpio-mcp23s08.txt @@ -10,6 +10,7 @@ Required properties: - "microchip,mcp23s08" for 8 GPIO SPI version - "microchip,mcp23s17" for 16 GPIO SPI version + - "microchip,mcp23s18" for 16 GPIO SPI version - "microchip,mcp23008" for 8 GPIO I2C version or - "microchip,mcp23017" for 16 GPIO I2C version of the chip NOTE: Do not use the old mcp prefix any more. It is deprecated and will be @@ -43,9 +44,6 @@ Optional properties: - first cell is the pin number - second cell is used to specify flags. - interrupt-controller: Marks the device node as a interrupt controller. -NOTE: The interrupt functionality is only supported for i2c versions of the -chips. The spi chips can also do the interrupts, but this is not supported by -the linux driver yet. Optional device specific properties: - microchip,irq-mirror: Sets the mirror flag in the IOCON register. Devices diff --git a/Documentation/devicetree/bindings/gpio/gpio-pisosr.txt b/Documentation/devicetree/bindings/gpio/gpio-pisosr.txt new file mode 100644 index 0000000..414a01c --- /dev/null +++ b/Documentation/devicetree/bindings/gpio/gpio-pisosr.txt @@ -0,0 +1,34 @@ +Generic Parallel-in/Serial-out Shift Register GPIO Driver + +This binding describes generic parallel-in/serial-out shift register +devices that can be used for GPI (General Purpose Input). This includes +SN74165 serial-out shift registers and the SN65HVS88x series of +industrial serializers. + +Required properties: + - compatible : Should be "pisosr-gpio". + - gpio-controller : Marks the device node as a GPIO controller. + - #gpio-cells : Should be two. For consumer use see gpio.txt. + +Optional properties: + - ngpios : Number of used GPIO lines (0..n-1), default is 8. + - load-gpios : GPIO pin specifier attached to load enable, this + pin is pulsed before reading from the device to + load input pin values into the the device. + +For other required and optional properties of SPI slave +nodes please refer to ../spi/spi-bus.txt. + +Example: + + gpio@0 { + compatible = "ti,sn65hvs882", "pisosr-gpio"; + gpio-controller; + #gpio-cells = <2>; + + load-gpios = <&gpio2 23 GPIO_ACTIVE_LOW>; + + reg = <0>; + spi-max-frequency = <1000000>; + spi-cpol; + }; diff --git a/Documentation/devicetree/bindings/gpio/gpio-ts4800.txt b/Documentation/devicetree/bindings/gpio/gpio-ts4800.txt new file mode 100644 index 0000000..92ea9c8 --- /dev/null +++ b/Documentation/devicetree/bindings/gpio/gpio-ts4800.txt @@ -0,0 +1,20 @@ +* TS-4800 FPGA's GPIO controller bindings + +Required properties: +- compatible: Must be "technologic,ts4800-gpio". +- #gpio-cells: Should be two. The first cell is the pin number. +- reg: Physical base address of the controller and length + of memory mapped region. + +Optional property: +- ngpios: See "gpio.txt" + +Example: + +gpio1: gpio { + compatible = "technologic,ts4800-gpio"; + reg = <0x10020 0x6>; + ngpios = <8>; + gpio-controller; + #gpio-cells = <2>; +}; diff --git a/Documentation/devicetree/bindings/gpio/gpio-xgene-sb.txt b/Documentation/devicetree/bindings/gpio/gpio-xgene-sb.txt index dae1300..5490c1d 100644 --- a/Documentation/devicetree/bindings/gpio/gpio-xgene-sb.txt +++ b/Documentation/devicetree/bindings/gpio/gpio-xgene-sb.txt @@ -1,10 +1,20 @@ APM X-Gene Standby GPIO controller bindings -This is a gpio controller in the standby domain. - -There are 20 GPIO pins from 0..21. There is no GPIO_DS14 or GPIO_DS15, -only GPIO_DS8..GPIO_DS13 support interrupts. The IRQ mapping -is currently 1-to-1 on interrupts 0x28 thru 0x2d. +This is a gpio controller in the standby domain. It also supports interrupt in +some particular pins which are sourced to its parent interrupt controller +as diagram below: + +-----------------+ + | X-Gene standby | + | GPIO controller +------ GPIO_0 ++------------+ | | ... +| Parent IRQ | EXT_INT_0 | +------ GPIO_8/EXT_INT_0 +| controller | (SPI40) | | ... +| (GICv2) +--------------+ +------ GPIO_[N+8]/EXT_INT_N +| | ... | | +| | EXT_INT_N | +------ GPIO_[N+9] +| | (SPI[40 + N])| | ... +| +--------------+ +------ GPIO_MAX ++------------+ +-----------------+ Required properties: - compatible: "apm,xgene-gpio-sb" for the X-Gene Standby GPIO controller @@ -15,10 +25,18 @@ Required properties: 0 = active high 1 = active low - gpio-controller: Marks the device node as a GPIO controller. -- interrupts: Shall contain exactly 6 interrupts. +- interrupts: The EXT_INT_0 parent interrupt resource must be listed first. +- interrupt-parent: Phandle of the parent interrupt controller. +- interrupt-cells: Should be two. + - first cell is 0-N coresponding for EXT_INT_0 to EXT_INT_N. + - second cell is used to specify flags. +- interrupt-controller: Marks the device node as an interrupt controller. +- apm,nr-gpios: Optional, specify number of gpios pin. +- apm,nr-irqs: Optional, specify number of interrupt pins. +- apm,irq-start: Optional, specify lowest gpio pin support interrupt. Example: - sbgpio: sbgpio@17001000 { + sbgpio: gpio@17001000{ compatible = "apm,xgene-gpio-sb"; reg = <0x0 0x17001000 0x0 0x400>; #gpio-cells = <2>; @@ -29,4 +47,19 @@ Example: <0x0 0x2b 0x1>, <0x0 0x2c 0x1>, <0x0 0x2d 0x1>; + interrupt-parent = <&gic>; + #interrupt-cells = <2>; + interrupt-controller; + apm,nr-gpios = <22>; + apm,nr-irqs = <6>; + apm,irq-start = <8>; + }; + + testuser { + compatible = "example,testuser"; + /* Use the GPIO_13/EXT_INT_5 line as an active high triggered + * level interrupt + */ + interrupts = <5 4>; + interrupt-parent = <&sbgpio>; }; diff --git a/Documentation/devicetree/bindings/gpio/microchip,pic32-gpio.txt b/Documentation/devicetree/bindings/gpio/microchip,pic32-gpio.txt new file mode 100644 index 0000000..ef37528 --- /dev/null +++ b/Documentation/devicetree/bindings/gpio/microchip,pic32-gpio.txt @@ -0,0 +1,49 @@ +* Microchip PIC32 GPIO devices (PIO). + +Required properties: + - compatible: "microchip,pic32mzda-gpio" + - reg: Base address and length for the device. + - interrupts: The port interrupt shared by all pins. + - gpio-controller: Marks the port as GPIO controller. + - #gpio-cells: Two. The first cell is the pin number and + the second cell is used to specify the gpio polarity as defined in + defined in <dt-bindings/gpio/gpio.h>: + 0 = GPIO_ACTIVE_HIGH + 1 = GPIO_ACTIVE_LOW + 2 = GPIO_OPEN_DRAIN + - interrupt-controller: Marks the device node as an interrupt controller. + - #interrupt-cells: Two. The first cell is the GPIO number and second cell + is used to specify the trigger type as defined in + <dt-bindings/interrupt-controller/irq.h>: + IRQ_TYPE_EDGE_RISING + IRQ_TYPE_EDGE_FALLING + IRQ_TYPE_EDGE_BOTH + - clocks: Clock specifier (see clock bindings for details). + - microchip,gpio-bank: Specifies which bank a controller owns. + - gpio-ranges: Interaction with the PINCTRL subsystem. + +Example: + +/* PORTA */ +gpio0: gpio0@1f860000 { + compatible = "microchip,pic32mzda-gpio"; + reg = <0x1f860000 0x100>; + interrupts = <118 IRQ_TYPE_LEVEL_HIGH>; + #gpio-cells = <2>; + gpio-controller; + interrupt-controller; + #interrupt-cells = <2>; + clocks = <&PBCLK4>; + microchip,gpio-bank = <0>; + gpio-ranges = <&pic32_pinctrl 0 0 16>; +}; + +keys { + ... + + button@sw1 { + label = "ESC"; + linux,code = <1>; + gpios = <&gpio0 12 0>; + }; +}; diff --git a/Documentation/devicetree/bindings/hsi/nokia-modem.txt b/Documentation/devicetree/bindings/hsi/nokia-modem.txt index 8a97978..53de1d9 100644 --- a/Documentation/devicetree/bindings/hsi/nokia-modem.txt +++ b/Documentation/devicetree/bindings/hsi/nokia-modem.txt @@ -7,6 +7,8 @@ properties are needed by the Nokia modem HSI client: Required properties: - compatible: Should be one of "nokia,n900-modem" + "nokia,n950-modem" + "nokia,n9-modem" - hsi-channel-names: Should contain the following strings "mcsaab-control" "speech-control" @@ -15,11 +17,11 @@ Required properties: - gpios: Should provide a GPIO handler for each GPIO listed in gpio-names - gpio-names: Should contain the following strings - "cmt_apeslpx" - "cmt_rst_rq" - "cmt_en" - "cmt_rst" - "cmt_bsi" + "cmt_apeslpx" (for n900, n950, n9) + "cmt_rst_rq" (for n900, n950, n9) + "cmt_en" (for n900, n950, n9) + "cmt_rst" (for n900) + "cmt_bsi" (for n900) - interrupts: Should be IRQ handle for modem's reset indication Example: diff --git a/Documentation/devicetree/bindings/hwmon/nsa320-mcu.txt b/Documentation/devicetree/bindings/hwmon/nsa320-mcu.txt new file mode 100644 index 0000000..0863e06 --- /dev/null +++ b/Documentation/devicetree/bindings/hwmon/nsa320-mcu.txt @@ -0,0 +1,20 @@ +Bindings for the fan / temperature monitor microcontroller used on +the Zyxel NSA 320 and several subsequent models. + +Required properties: +- compatible : "zyxel,nsa320-mcu" +- data-gpios : The GPIO pin connected to the data line on the MCU +- clk-gpios : The GPIO pin connected to the clock line on the MCU +- act-gpios : The GPIO pin connected to the active line on the MCU + +Example: + + hwmon { + compatible = "zyxel,nsa320-mcu"; + pinctrl-0 = <&pmx_mcu_data &pmx_mcu_clk &pmx_mcu_act>; + pinctrl-names = "default"; + + data-gpios = <&gpio0 14 GPIO_ACTIVE_HIGH>; + clk-gpios = <&gpio0 16 GPIO_ACTIVE_HIGH>; + act-gpios = <&gpio0 17 GPIO_ACTIVE_LOW>; + }; diff --git a/Documentation/devicetree/bindings/hwmon/ntc_thermistor.txt b/Documentation/devicetree/bindings/hwmon/ntc_thermistor.txt index a04a80f..c3b9c4c 100644 --- a/Documentation/devicetree/bindings/hwmon/ntc_thermistor.txt +++ b/Documentation/devicetree/bindings/hwmon/ntc_thermistor.txt @@ -10,6 +10,7 @@ Requires node properties: "murata,ncp03wb473" "murata,ncp15wl333" "murata,ncp03wf104" + "murata,ncp15xh103" /* Usage of vendor name "ntc" is deprecated */ <DEPRECATED> "ntc,ncp15wb473" diff --git a/Documentation/devicetree/bindings/i2c/i2c-demux-pinctrl.txt b/Documentation/devicetree/bindings/i2c/i2c-demux-pinctrl.txt new file mode 100644 index 0000000..6078aef --- /dev/null +++ b/Documentation/devicetree/bindings/i2c/i2c-demux-pinctrl.txt @@ -0,0 +1,135 @@ +Pinctrl-based I2C Bus DeMux + +This binding describes an I2C bus demultiplexer that uses pin multiplexing to +route the I2C signals, and represents the pin multiplexing configuration using +the pinctrl device tree bindings. This may be used to select one I2C IP core at +runtime which may have a better feature set for a given task than another I2C +IP core on the SoC. The most simple example is to fall back to GPIO bitbanging +if your current runtime configuration hits an errata of the internal IP core. + + +-------------------------------+ + | SoC | + | | +-----+ +-----+ + | +------------+ | | dev | | dev | + | |I2C IP Core1|--\ | +-----+ +-----+ + | +------------+ \-------+ | | | + | |Pinctrl|--|------+--------+ + | +------------+ +-------+ | + | |I2C IP Core2|--/ | + | +------------+ | + | | + +-------------------------------+ + +Required properties: +- compatible: "i2c-demux-pinctrl" +- i2c-parent: List of phandles of I2C masters available for selection. The first + one will be used as default. +- i2c-bus-name: The name of this bus. Also needed as pinctrl-name for the I2C + parents. + +Furthermore, I2C mux properties and child nodes. See mux.txt in this directory. + +Example: + +Here is a snipplet for a bus to be demuxed. It contains various i2c clients for +HDMI, so the bus is named "i2c-hdmi": + + i2chdmi: i2c@8 { + + compatible = "i2c-demux-pinctrl"; + i2c-parent = <&gpioi2c>, <&iic2>, <&i2c2>; + i2c-bus-name = "i2c-hdmi"; + #address-cells = <1>; + #size-cells = <0>; + + ak4643: sound-codec@12 { + compatible = "asahi-kasei,ak4643"; + + #sound-dai-cells = <0>; + reg = <0x12>; + }; + + composite-in@20 { + compatible = "adi,adv7180"; + reg = <0x20>; + remote = <&vin1>; + + port { + adv7180: endpoint { + bus-width = <8>; + remote-endpoint = <&vin1ep0>; + }; + }; + }; + + hdmi@39 { + compatible = "adi,adv7511w"; + reg = <0x39>; + interrupt-parent = <&gpio1>; + interrupts = <15 IRQ_TYPE_LEVEL_LOW>; + + adi,input-depth = <8>; + adi,input-colorspace = "rgb"; + adi,input-clock = "1x"; + adi,input-style = <1>; + adi,input-justification = "evenly"; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + adv7511_in: endpoint { + remote-endpoint = <&du_out_lvds0>; + }; + }; + + port@1 { + reg = <1>; + adv7511_out: endpoint { + remote-endpoint = <&hdmi_con>; + }; + }; + }; + }; + }; + +And for clarification, here are the snipplets for the i2c-parents: + + gpioi2c: i2c@9 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "i2c-gpio"; + status = "disabled"; + gpios = <&gpio5 6 GPIO_ACTIVE_HIGH /* sda */ + &gpio5 5 GPIO_ACTIVE_HIGH /* scl */ + >; + i2c-gpio,delay-us = <5>; + }; + +... + +&i2c2 { + pinctrl-0 = <&i2c2_pins>; + pinctrl-names = "i2c-hdmi"; + + clock-frequency = <100000>; +}; + +... + +&iic2 { + pinctrl-0 = <&iic2_pins>; + pinctrl-names = "i2c-hdmi"; + + clock-frequency = <100000>; +}; + +Please note: + +- pinctrl properties for the parent I2C controllers need a pinctrl state + with the same name as i2c-bus-name, not "default"! + +- the i2c masters must have their status "disabled". This driver will + enable them at runtime when needed. diff --git a/Documentation/devicetree/bindings/i2c/i2c-imx.txt b/Documentation/devicetree/bindings/i2c/i2c-imx.txt index eab5836..b967544 100644 --- a/Documentation/devicetree/bindings/i2c/i2c-imx.txt +++ b/Documentation/devicetree/bindings/i2c/i2c-imx.txt @@ -11,7 +11,7 @@ Required properties: Optional properties: - clock-frequency : Constains desired I2C/HS-I2C bus clock frequency in Hz. - The absence of the propoerty indicates the default frequency 100 kHz. + The absence of the property indicates the default frequency 100 kHz. - dmas: A list of two dma specifiers, one for each entry in dma-names. - dma-names: should contain "tx" and "rx". - scl-gpios: specify the gpio related to SCL pin diff --git a/Documentation/devicetree/bindings/i2c/i2c-rcar.txt b/Documentation/devicetree/bindings/i2c/i2c-rcar.txt index 95e9722..cf8bfc9 100644 --- a/Documentation/devicetree/bindings/i2c/i2c-rcar.txt +++ b/Documentation/devicetree/bindings/i2c/i2c-rcar.txt @@ -17,7 +17,7 @@ Required properties: Optional properties: - clock-frequency: desired I2C bus clock frequency in Hz. The absence of this - propoerty indicates the default frequency 100 kHz. + property indicates the default frequency 100 kHz. - clocks: clock specifier. - i2c-scl-falling-time-ns: see i2c.txt diff --git a/Documentation/devicetree/bindings/i2c/i2c-rk3x.txt b/Documentation/devicetree/bindings/i2c/i2c-rk3x.txt index f0d71bc..0b4a85f 100644 --- a/Documentation/devicetree/bindings/i2c/i2c-rk3x.txt +++ b/Documentation/devicetree/bindings/i2c/i2c-rk3x.txt @@ -6,8 +6,8 @@ RK3xxx SoCs. Required properties : - reg : Offset and length of the register set for the device - - compatible : should be "rockchip,rk3066-i2c", "rockchip,rk3188-i2c" or - "rockchip,rk3288-i2c". + - compatible : should be "rockchip,rk3066-i2c", "rockchip,rk3188-i2c", + "rockchip,rk3228-i2c" or "rockchip,rk3288-i2c". - interrupts : interrupt number - clocks : parent clock diff --git a/Documentation/devicetree/bindings/i2c/i2c-sirf.txt b/Documentation/devicetree/bindings/i2c/i2c-sirf.txt index 7baf9e1..2701eef 100644 --- a/Documentation/devicetree/bindings/i2c/i2c-sirf.txt +++ b/Documentation/devicetree/bindings/i2c/i2c-sirf.txt @@ -8,7 +8,7 @@ Required properties : Optional properties: - clock-frequency : Constains desired I2C/HS-I2C bus clock frequency in Hz. - The absence of the propoerty indicates the default frequency 100 kHz. + The absence of the property indicates the default frequency 100 kHz. Examples : diff --git a/Documentation/devicetree/bindings/i2c/i2c-xiic.txt b/Documentation/devicetree/bindings/i2c/i2c-xiic.txt index ceabbe9..caf42e9 100644 --- a/Documentation/devicetree/bindings/i2c/i2c-xiic.txt +++ b/Documentation/devicetree/bindings/i2c/i2c-xiic.txt @@ -6,14 +6,17 @@ Required properties: - interrupts : IIC controller unterrupt - #address-cells = <1> - #size-cells = <0> +- clocks: Input clock specifier. Refer to common clock bindings. Optional properties: - Child nodes conforming to i2c bus binding +- clock-names: Input clock name, should be 'pclk'. Example: axi_iic_0: i2c@40800000 { compatible = "xlnx,xps-iic-2.00.a"; + clocks = <&clkc 15>; interrupts = < 1 2 >; reg = < 0x40800000 0x10000 >; diff --git a/Documentation/devicetree/bindings/iio/accel/mma8452.txt b/Documentation/devicetree/bindings/iio/accel/mma8452.txt index 3c10e85..165937e 100644 --- a/Documentation/devicetree/bindings/iio/accel/mma8452.txt +++ b/Documentation/devicetree/bindings/iio/accel/mma8452.txt @@ -1,8 +1,10 @@ -Freescale MMA8452Q, MMA8453Q, MMA8652FC or MMA8653FC triaxial accelerometer +Freescale MMA8451Q, MMA8452Q, MMA8453Q, MMA8652FC or MMA8653FC +triaxial accelerometer Required properties: - compatible: should contain one of + * "fsl,mma8451" * "fsl,mma8452" * "fsl,mma8453" * "fsl,mma8652" diff --git a/Documentation/devicetree/bindings/iio/adc/at91-sama5d2_adc.txt b/Documentation/devicetree/bindings/iio/adc/at91-sama5d2_adc.txt new file mode 100644 index 0000000..3223684 --- /dev/null +++ b/Documentation/devicetree/bindings/iio/adc/at91-sama5d2_adc.txt @@ -0,0 +1,28 @@ +* AT91 SAMA5D2 Analog to Digital Converter (ADC) + +Required properties: + - compatible: Should be "atmel,sama5d2-adc". + - reg: Should contain ADC registers location and length. + - interrupts: Should contain the IRQ line for the ADC. + - clocks: phandle to device clock. + - clock-names: Must be "adc_clk". + - vref-supply: Supply used as reference for conversions. + - vddana-supply: Supply for the adc device. + - atmel,min-sample-rate-hz: Minimum sampling rate, it depends on SoC. + - atmel,max-sample-rate-hz: Maximum sampling rate, it depends on SoC. + - atmel,startup-time-ms: Startup time expressed in ms, it depends on SoC. + +Example: + +adc: adc@fc030000 { + compatible = "atmel,sama5d2-adc"; + reg = <0xfc030000 0x100>; + interrupts = <40 IRQ_TYPE_LEVEL_HIGH 7>; + clocks = <&adc_clk>; + clock-names = "adc_clk"; + atmel,min-sample-rate-hz = <200000>; + atmel,max-sample-rate-hz = <20000000>; + atmel,startup-time-ms = <4>; + vddana-supply = <&vdd_3v3_lp_reg>; + vref-supply = <&vdd_3v3_lp_reg>; +} diff --git a/Documentation/devicetree/bindings/iio/adc/fsl,imx25-gcq.txt b/Documentation/devicetree/bindings/iio/adc/fsl,imx25-gcq.txt new file mode 100644 index 0000000..b0866d3 --- /dev/null +++ b/Documentation/devicetree/bindings/iio/adc/fsl,imx25-gcq.txt @@ -0,0 +1,58 @@ +Freescale i.MX25 ADC GCQ device + +This is a generic conversion queue device that can convert any of the +analog inputs using the ADC unit of the i.MX25. + +Required properties: + - compatible: Should be "fsl,imx25-gcq". + - reg: Should be the register range of the module. + - interrupts: Should be the interrupt number of the module. + Typically this is <1>. + - interrupt-parent: phandle to the tsadc module of the i.MX25. + - #address-cells: Should be <1> (setting for the subnodes) + - #size-cells: Should be <0> (setting for the subnodes) + +Optional properties: + - vref-ext-supply: The regulator supplying the ADC reference voltage. + Required when at least one subnode uses the this reference. + - vref-xp-supply: The regulator supplying the ADC reference voltage on pin XP. + Required when at least one subnode uses this reference. + - vref-yp-supply: The regulator supplying the ADC reference voltage on pin YP. + Required when at least one subnode uses this reference. + +Sub-nodes: +Optionally you can define subnodes which define the reference voltage +for the analog inputs. + +Required properties for subnodes: + - reg: Should be the number of the analog input. + 0: xp + 1: yp + 2: xn + 3: yn + 4: wiper + 5: inaux0 + 6: inaux1 + 7: inaux2 +Optional properties for subnodes: + - fsl,adc-refp: specifies the positive reference input as defined in + <dt-bindings/iio/adc/fsl-imx25-gcq.h> + - fsl,adc-refn: specifies the negative reference input as defined in + <dt-bindings/iio/adc/fsl-imx25-gcq.h> + +Example: + + adc: adc@50030800 { + compatible = "fsl,imx25-gcq"; + reg = <0x50030800 0x60>; + interrupt-parent = <&tscadc>; + interrupts = <1>; + #address-cells = <1>; + #size-cells = <0>; + + inaux@5 { + reg = <5>; + fsl,adc-refp = <MX25_ADC_REFP_INT>; + fsl,adc-refn = <MX25_ADC_REFN_NGND>; + }; + }; diff --git a/Documentation/devicetree/bindings/iio/adc/mcp3422.txt b/Documentation/devicetree/bindings/iio/adc/mcp3422.txt index dcae4cc..82bcce0 100644 --- a/Documentation/devicetree/bindings/iio/adc/mcp3422.txt +++ b/Documentation/devicetree/bindings/iio/adc/mcp3422.txt @@ -6,6 +6,7 @@ Required properties: "microchip,mcp3422" or "microchip,mcp3423" or "microchip,mcp3424" or + "microchip,mcp3425" or "microchip,mcp3426" or "microchip,mcp3427" or "microchip,mcp3428" diff --git a/Documentation/devicetree/bindings/iio/adc/ti-adc0832.txt b/Documentation/devicetree/bindings/iio/adc/ti-adc0832.txt new file mode 100644 index 0000000..d911305 --- /dev/null +++ b/Documentation/devicetree/bindings/iio/adc/ti-adc0832.txt @@ -0,0 +1,19 @@ +* Texas Instruments' ADC0831/ADC0832/ADC0832/ADC0838 + +Required properties: + - compatible: Should be one of + * "ti,adc0831" + * "ti,adc0832" + * "ti,adc0834" + * "ti,adc0838" + - reg: spi chip select number for the device + - vref-supply: The regulator supply for ADC reference voltage + - spi-max-frequency: Max SPI frequency to use (< 400000) + +Example: +adc@0 { + compatible = "ti,adc0832"; + reg = <0>; + vref-supply = <&vdd_supply>; + spi-max-frequency = <200000>; +}; diff --git a/Documentation/devicetree/bindings/iio/chemical/atlas,ph-sm.txt b/Documentation/devicetree/bindings/iio/chemical/atlas,ph-sm.txt new file mode 100644 index 0000000..cffa190 --- /dev/null +++ b/Documentation/devicetree/bindings/iio/chemical/atlas,ph-sm.txt @@ -0,0 +1,22 @@ +* Atlas Scientific pH-SM OEM sensor + +http://www.atlas-scientific.com/_files/_datasheets/_oem/pH_oem_datasheet.pdf + +Required properties: + + - compatible: must be "atlas,ph-sm" + - reg: the I2C address of the sensor + - interrupt-parent: should be the phandle for the interrupt controller + - interrupts: the sole interrupt generated by the device + + Refer to interrupt-controller/interrupts.txt for generic interrupt client + node bindings. + +Example: + +atlas@65 { + compatible = "atlas,ph-sm"; + reg = <0x65>; + interrupt-parent = <&gpio1>; + interrupts = <16 2>; +}; diff --git a/Documentation/devicetree/bindings/iio/dac/vf610-dac.txt b/Documentation/devicetree/bindings/iio/dac/vf610-dac.txt new file mode 100644 index 0000000..20c6c7a --- /dev/null +++ b/Documentation/devicetree/bindings/iio/dac/vf610-dac.txt @@ -0,0 +1,20 @@ +Freescale vf610 Digital to Analog Converter bindings + +The devicetree bindings are for the new DAC driver written for +vf610 SoCs from Freescale. + +Required properties: +- compatible: Should contain "fsl,vf610-dac" +- reg: Offset and length of the register set for the device +- interrupts: Should contain the interrupt for the device +- clocks: The clock is needed by the DAC controller +- clock-names: Must contain "dac" matching entry in the clocks property. + +Example: +dac0: dac@400cc000 { + compatible = "fsl,vf610-dac"; + reg = <0x400cc000 0x1000>; + interrupts = <55 IRQ_TYPE_LEVEL_HIGH>; + clock-names = "dac"; + clocks = <&clks VF610_CLK_DAC0>; +}; diff --git a/Documentation/devicetree/bindings/iio/health/afe4403.txt b/Documentation/devicetree/bindings/iio/health/afe4403.txt new file mode 100644 index 0000000..2fffd70 --- /dev/null +++ b/Documentation/devicetree/bindings/iio/health/afe4403.txt @@ -0,0 +1,34 @@ +Texas Instruments AFE4403 Heart rate and Pulse Oximeter + +Required properties: + - compatible : Should be "ti,afe4403". + - reg : SPI chip select address of device. + - tx-supply : Regulator supply to transmitting LEDs. + - interrupt-parent : Phandle to he parent interrupt controller. + - interrupts : The interrupt line the device ADC_RDY pin is + connected to. For details refer to, + ../../interrupt-controller/interrupts.txt. + +Optional properties: + - reset-gpios : GPIO used to reset the device. + For details refer to, ../../gpio/gpio.txt. + +For other required and optional properties of SPI slave nodes +please refer to ../../spi/spi-bus.txt. + +Example: + +&spi0 { + heart_mon@0 { + compatible = "ti,afe4403"; + reg = <0>; + spi-max-frequency = <10000000>; + + tx-supply = <&vbat>; + + interrupt-parent = <&gpio1>; + interrupts = <28 IRQ_TYPE_EDGE_RISING>; + + reset-gpios = <&gpio1 16 GPIO_ACTIVE_LOW>; + }; +}; diff --git a/Documentation/devicetree/bindings/iio/health/afe4404.txt b/Documentation/devicetree/bindings/iio/health/afe4404.txt new file mode 100644 index 0000000..de69f20 --- /dev/null +++ b/Documentation/devicetree/bindings/iio/health/afe4404.txt @@ -0,0 +1,30 @@ +Texas Instruments AFE4404 Heart rate and Pulse Oximeter + +Required properties: + - compatible : Should be "ti,afe4404". + - reg : I2C address of the device. + - tx-supply : Regulator supply to transmitting LEDs. + - interrupt-parent : Phandle to he parent interrupt controller. + - interrupts : The interrupt line the device ADC_RDY pin is + connected to. For details refer to, + ../interrupt-controller/interrupts.txt. + +Optional properties: + - reset-gpios : GPIO used to reset the device. + For details refer to, ../gpio/gpio.txt. + +Example: + +&i2c2 { + heart_mon@58 { + compatible = "ti,afe4404"; + reg = <0x58>; + + tx-supply = <&vbat>; + + interrupt-parent = <&gpio1>; + interrupts = <28 IRQ_TYPE_EDGE_RISING>; + + reset-gpios = <&gpio1 16 GPIO_ACTIVE_LOW>; + }; +}; diff --git a/Documentation/devicetree/bindings/iio/health/max30100.txt b/Documentation/devicetree/bindings/iio/health/max30100.txt index f6fbac6..295a9ed 100644 --- a/Documentation/devicetree/bindings/iio/health/max30100.txt +++ b/Documentation/devicetree/bindings/iio/health/max30100.txt @@ -11,11 +11,19 @@ Required properties: Refer to interrupt-controller/interrupts.txt for generic interrupt client node bindings. +Optional properties: + - maxim,led-current-microamp: configuration for LED current in microamperes + while the engine is running. First indexed value is the configuration for + the RED LED, and second value is for the IR LED. + + Refer to the datasheet for the allowed current values. + Example: max30100@057 { compatible = "maxim,max30100"; reg = <57>; + maxim,led-current-microamp = <24000 50000>; interrupt-parent = <&gpio1>; interrupts = <16 2>; }; diff --git a/Documentation/devicetree/bindings/iio/iio-bindings.txt b/Documentation/devicetree/bindings/iio/iio-bindings.txt index 0b447d9..68d6f8c 100644 --- a/Documentation/devicetree/bindings/iio/iio-bindings.txt +++ b/Documentation/devicetree/bindings/iio/iio-bindings.txt @@ -82,7 +82,7 @@ vdd channel is connected to output 0 of the &ref device. ... - iio_hwmon { + iio-hwmon { compatible = "iio-hwmon"; io-channels = <&adc 0>, <&adc 1>, <&adc 2>, <&adc 3>, <&adc 4>, <&adc 5>, diff --git a/Documentation/devicetree/bindings/iio/light/opt3001.txt b/Documentation/devicetree/bindings/iio/light/opt3001.txt new file mode 100644 index 0000000..eac30d5 --- /dev/null +++ b/Documentation/devicetree/bindings/iio/light/opt3001.txt @@ -0,0 +1,26 @@ +* Texas Instruments OPT3001 Ambient Light Sensor + +The driver supports interrupt-driven and interrupt-less operation, depending +on whether an interrupt property has been populated into the DT. Note that +the optional generation of IIO events on rising/falling light threshold changes +requires the use of interrupts. Without interrupts, only the simple reading +of the current light value is supported through the IIO API. + +http://www.ti.com/product/opt3001 + +Required properties: + - compatible: should be "ti,opt3001" + - reg: the I2C address of the sensor + +Optional properties: + - interrupt-parent: should be the phandle for the interrupt controller + - interrupts: interrupt mapping for GPIO IRQ (configure for falling edge) + +Example: + +opt3001@44 { + compatible = "ti,opt3001"; + reg = <0x44>; + interrupt-parent = <&gpio1>; + interrupts = <28 IRQ_TYPE_EDGE_FALLING>; +}; diff --git a/Documentation/devicetree/bindings/input/ads7846.txt b/Documentation/devicetree/bindings/input/ads7846.txt index 33a1638..c6cfe2e 100644 --- a/Documentation/devicetree/bindings/input/ads7846.txt +++ b/Documentation/devicetree/bindings/input/ads7846.txt @@ -29,6 +29,8 @@ Optional properties: ti,vref-delay-usecs vref supply delay in usecs, 0 for external vref (u16). ti,vref-mv The VREF voltage, in millivolts (u16). + Set to 0 to use internal refernce + (ADS7846). ti,keep-vref-on set to keep vref on for differential measurements as well ti,swap-xy swap x and y axis diff --git a/Documentation/devicetree/bindings/input/rmi4/rmi_2d_sensor.txt b/Documentation/devicetree/bindings/input/rmi4/rmi_2d_sensor.txt new file mode 100644 index 0000000..f2c30c8 --- /dev/null +++ b/Documentation/devicetree/bindings/input/rmi4/rmi_2d_sensor.txt @@ -0,0 +1,56 @@ +Synaptics RMI4 2D Sensor Device Binding + +The Synaptics RMI4 core is able to support RMI4 devices using different +transports and different functions. This file describes the device tree +bindings for devices which contain 2D sensors using Function 11 or +Function 12. Complete documentation for transports and other functions +can be found in: +Documentation/devicetree/bindings/input/rmi4. + +RMI4 Function 11 and Function 12 are for 2D touch position sensing. +Additional documentation for F11 can be found at: +http://www.synaptics.com/sites/default/files/511-000136-01-Rev-E-RMI4-Interfacing-Guide.pdf + +Optional Touch Properties: +Description in Documentation/devicetree/bindings/input/touch +- touchscreen-inverted-x +- touchscreen-inverted-y +- touchscreen-swapped-x-y +- touchscreen-x-mm +- touchscreen-y-mm + +Optional Properties: +- syna,clip-x-low: Sets a minimum value for X. +- syna,clip-y-low: Sets a minimum value for Y. +- syna,clip-x-high: Sets a maximum value for X. +- syna,clip-y-high: Sets a maximum value for Y. +- syna,offset-x: Add an offset to X. +- syna,offset-y: Add an offset to Y. +- syna,delta-x-threshold: Set the minimum distance on the X axis required + to generate an interrupt in reduced reporting + mode. +- syna,delta-y-threshold: Set the minimum distance on the Y axis required + to generate an interrupt in reduced reporting + mode. +- syna,sensor-type: Set the sensor type. 1 for touchscreen 2 for touchpad. +- syna,disable-report-mask: Mask for disabling posiiton reporting. Used to + disable reporing absolute position data. +- syna,rezero-wait-ms: Time in miliseconds to wait after issuing a rezero + command. + + +Example of a RMI4 I2C device with F11: +Example: + &i2c1 { + rmi4-i2c-dev@2c { + compatible = "syna,rmi4-i2c"; + + ... + + rmi4-f11@11 { + reg = <0x11>; + touchscreen-inverted-y; + syna,sensor-type = <2>; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/input/rmi4/rmi_f01.txt b/Documentation/devicetree/bindings/input/rmi4/rmi_f01.txt new file mode 100644 index 0000000..079cad2 --- /dev/null +++ b/Documentation/devicetree/bindings/input/rmi4/rmi_f01.txt @@ -0,0 +1,39 @@ +Synaptics RMI4 F01 Device Binding + +The Synaptics RMI4 core is able to support RMI4 devices using different +transports and different functions. This file describes the device tree +bindings for devices which contain Function 1. Complete documentation +for transports and other functions can be found in: +Documentation/devicetree/bindings/input/rmi4. + +Additional documentation for F01 can be found at: +http://www.synaptics.com/sites/default/files/511-000136-01-Rev-E-RMI4-Interfacing-Guide.pdf + +Optional Properties: +- syna,nosleep-mode: If set the device will run at full power without sleeping. + nosleep has 3 modes, 0 will not change the default + setting, 1 will disable nosleep (allow sleeping), + and 2 will enable nosleep (disabling sleep). +- syna,wakeup-threshold: Defines the amplitude of the disturbance to the + background capacitance that will cause the + device to wake from dozing. +- syna,doze-holdoff-ms: The delay to wait after the last finger lift and the + first doze cycle. +- syna,doze-interval-ms: The time period that the device sleeps between finger + activity. + + +Example of a RMI4 I2C device with F01: + Example: + &i2c1 { + rmi4-i2c-dev@2c { + compatible = "syna,rmi4-i2c"; + + ... + + rmi4-f01@1 { + reg = <0x1>; + syna,nosleep-mode = <1>; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/input/rmi4/rmi_i2c.txt b/Documentation/devicetree/bindings/input/rmi4/rmi_i2c.txt new file mode 100644 index 0000000..95fa715 --- /dev/null +++ b/Documentation/devicetree/bindings/input/rmi4/rmi_i2c.txt @@ -0,0 +1,53 @@ +Synaptics RMI4 I2C Device Binding + +The Synaptics RMI4 core is able to support RMI4 devices using different +transports and different functions. This file describes the device tree +bindings for devices using the I2C transport driver. Complete documentation +for other transports and functions can be found in +Documentation/devicetree/bindings/input/rmi4. + +Required Properties: +- compatible: syna,rmi4-i2c +- reg: I2C address +- #address-cells: Set to 1 to indicate that the function child nodes + consist of only on uint32 value. +- #size-cells: Set to 0 to indicate that the function child nodes do not + have a size property. + +Optional Properties: +- interrupts: interrupt which the rmi device is connected to. +- interrupt-parent: The interrupt controller. +See Documentation/devicetree/bindings/interrupt-controller/interrupts.txt + +- syna,reset-delay-ms: The number of milliseconds to wait after resetting the + device. + +Function Parameters: +Parameters specific to RMI functions are contained in child nodes of the rmi device + node. Documentation for the parameters of each function can be found in: +Documentation/devicetree/bindings/input/rmi4/rmi_f*.txt. + + + +Example: + &i2c1 { + rmi4-i2c-dev@2c { + compatible = "syna,rmi4-i2c"; + reg = <0x2c>; + #address-cells = <1>; + #size-cells = <0>; + interrupt-parent = <&gpio>; + interrupts = <4 2>; + + rmi4-f01@1 { + reg = <0x1>; + syna,nosleep-mode = <1>; + }; + + rmi4-f11@11 { + reg = <0x11>; + touchscreen-inverted-y; + syna,sensor-type = <2>; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/input/rmi4/rmi_spi.txt b/Documentation/devicetree/bindings/input/rmi4/rmi_spi.txt new file mode 100644 index 0000000..a4ca782 --- /dev/null +++ b/Documentation/devicetree/bindings/input/rmi4/rmi_spi.txt @@ -0,0 +1,57 @@ +Synaptics RMI4 SPI Device Binding + +The Synaptics RMI4 core is able to support RMI4 devices using different +transports and different functions. This file describes the device tree +bindings for devices using the SPI transport driver. Complete documentation +for other transports and functions can be found in +Documentation/devicetree/bindings/input/rmi4. + +Required Properties: +- compatible: syna,rmi4-spi +- reg: Chip select address for the device +- #address-cells: Set to 1 to indicate that the function child nodes + consist of only on uint32 value. +- #size-cells: Set to 0 to indicate that the function child nodes do not + have a size property. + +Optional Properties: +- interrupts: interrupt which the rmi device is connected to. +- interrupt-parent: The interrupt controller. +See Documentation/devicetree/bindings/interrupt-controller/interrupts.txt + +- spi-rx-delay-us: microsecond delay after a read transfer. +- spi-tx-delay-us: microsecond delay after a write transfer. + +Function Parameters: +Parameters specific to RMI functions are contained in child nodes of the rmi device + node. Documentation for the parameters of each function can be found in: +Documentation/devicetree/bindings/input/rmi4/rmi_f*.txt. + + + +Example: + spi@7000d800 { + rmi4-spi-dev@0 { + compatible = "syna,rmi4-spi"; + reg = <0x0>; + #address-cells = <1>; + #size-cells = <0>; + spi-max-frequency = <4000000>; + spi-cpha; + spi-cpol; + interrupt-parent = <&gpio>; + interrupts = <TEGRA_GPIO(K, 2) 0x2>; + spi-rx-delay-us = <30>; + + rmi4-f01@1 { + reg = <0x1>; + syna,nosleep-mode = <1>; + }; + + rmi4-f11@11 { + reg = <0x11>; + touchscreen-inverted-y; + syna,sensor-type = <2>; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/input/rotary-encoder.txt b/Documentation/devicetree/bindings/input/rotary-encoder.txt index de99cbb..6c9f0c8 100644 --- a/Documentation/devicetree/bindings/input/rotary-encoder.txt +++ b/Documentation/devicetree/bindings/input/rotary-encoder.txt @@ -1,7 +1,7 @@ Rotary encoder DT bindings Required properties: -- gpios: a spec for two GPIOs to be used +- gpios: a spec for at least two GPIOs to be used, most significant first Optional properties: - linux,axis: the input subsystem axis to map to this rotary encoder. diff --git a/Documentation/devicetree/bindings/input/touchscreen/ad7879.txt b/Documentation/devicetree/bindings/input/touchscreen/ad7879.txt new file mode 100644 index 0000000..e3f22d2 --- /dev/null +++ b/Documentation/devicetree/bindings/input/touchscreen/ad7879.txt @@ -0,0 +1,53 @@ +* Analog Devices AD7879(-1)/AD7889(-1) touchscreen interface (SPI/I2C) + +Required properties: +- compatible : for SPI slave, use "adi,ad7879" + for I2C slave, use "adi,ad7879-1" +- reg : SPI chipselect/I2C slave address + See spi-bus.txt for more SPI slave properties +- interrupt-parent : the phandle for the interrupt controller +- interrupts : touch controller interrupt +- touchscreen-max-pressure : maximum reported pressure +- adi,resistance-plate-x : total resistance of X-plate (for pressure + calculation) +Optional properties: +- touchscreen-swapped-x-y : X and Y axis are swapped (boolean) +- adi,first-conversion-delay : 0-12: In 128us steps (starting with 128us) + 13 : 2.560ms + 14 : 3.584ms + 15 : 4.096ms + This property has to be a '/bits/ 8' value +- adi,acquisition-time : 0: 2us + 1: 4us + 2: 8us + 3: 16us + This property has to be a '/bits/ 8' value +- adi,median-filter-size : 0: disabled + 1: 4 measurements + 2: 8 measurements + 3: 16 measurements + This property has to be a '/bits/ 8' value +- adi,averaging : 0: 2 middle values (1 if median disabled) + 1: 4 middle values + 2: 8 middle values + 3: 16 values + This property has to be a '/bits/ 8' value +- adi,conversion-interval: : 0 : convert one time only + 1-255: 515us + val * 35us (up to 9.440ms) + This property has to be a '/bits/ 8' value + +Example: + + ad7879@2c { + compatible = "adi,ad7879-1"; + reg = <0x2c>; + interrupt-parent = <&gpio1>; + interrupts = <13 IRQ_TYPE_EDGE_FALLING>; + touchscreen-max-pressure = <4096>; + adi,resistance-plate-x = <120>; + adi,first-conversion-delay = /bits/ 8 <3>; + adi,acquisition-time = /bits/ 8 <1>; + adi,median-filter-size = /bits/ 8 <2>; + adi,averaging = /bits/ 8 <1>; + adi,conversion-interval = /bits/ 8 <255>; + }; diff --git a/Documentation/devicetree/bindings/input/touchscreen/cyttsp.txt b/Documentation/devicetree/bindings/input/touchscreen/cyttsp.txt new file mode 100644 index 0000000..b75d4cf --- /dev/null +++ b/Documentation/devicetree/bindings/input/touchscreen/cyttsp.txt @@ -0,0 +1,95 @@ +* Cypress cyttsp touchscreen controller + +Required properties: + - compatible : must be "cypress,cyttsp-i2c" or "cypress,cyttsp-spi" + - reg : Device I2C address or SPI chip select number + - spi-max-frequency : Maximum SPI clocking speed of the device (for cyttsp-spi) + - interrupt-parent : the phandle for the gpio controller + (see interrupt binding[0]). + - interrupts : (gpio) interrupt to which the chip is connected + (see interrupt binding[0]). + - bootloader-key : the 8-byte bootloader key that is required to switch + the chip from bootloader mode (default mode) to + application mode. + This property has to be specified as an array of 8 + '/bits/ 8' values. + +Optional properties: + - reset-gpios : the reset gpio the chip is connected to + (see GPIO binding[1] for more details). + - touchscreen-size-x : horizontal resolution of touchscreen (in pixels) + - touchscreen-size-y : vertical resolution of touchscreen (in pixels) + - touchscreen-fuzz-x : horizontal noise value of the absolute input device + (in pixels) + - touchscreen-fuzz-y : vertical noise value of the absolute input device + (in pixels) + - active-distance : the distance in pixels beyond which a touch must move + before movement is detected and reported by the device. + Valid values: 0-15. + - active-interval-ms : the minimum period in ms between consecutive + scanning/processing cycles when the chip is in active mode. + Valid values: 0-255. + - lowpower-interval-ms : the minimum period in ms between consecutive + scanning/processing cycles when the chip is in low-power mode. + Valid values: 0-2550 + - touch-timeout-ms : minimum time in ms spent in the active power state while no + touches are detected before entering low-power mode. + Valid values: 0-2550 + - use-handshake : enable register-based handshake (boolean). This should + only be used if the chip is configured to use 'blocking + communication with timeout' (in this case the device + generates an interrupt at the end of every + scanning/processing cycle). + +[0]: Documentation/devicetree/bindings/interrupt-controller/interrupts.txt +[1]: Documentation/devicetree/bindings/gpio/gpio.txt + +Example: + &i2c1 { + /* ... */ + cyttsp@a { + compatible = "cypress,cyttsp-i2c"; + reg = <0xa>; + interrupt-parent = <&gpio0>; + interrupts = <28 0>; + reset-gpios = <&gpio3 4 GPIO_ACTIVE_LOW>; + + touchscreen-size-x = <800>; + touchscreen-size-y = <480>; + touchscreen-fuzz-x = <4>; + touchscreen-fuzz-y = <7>; + + bootloader-key = /bits/ 8 <0x01 0x02 0x03 0x04 0x05 0x06 0x07 0x08>; + active-distance = <8>; + active-interval-ms = <0>; + lowpower-interval-ms = <200>; + touch-timeout-ms = <100>; + }; + + /* ... */ + }; + + &mcspi1 { + /* ... */ + cyttsp@0 { + compatible = "cypress,cyttsp-spi"; + spi-max-frequency = <6000000>; + reg = <0>; + interrupt-parent = <&gpio0>; + interrupts = <28 0>; + reset-gpios = <&gpio3 4 GPIO_ACTIVE_LOW>; + + touchscreen-size-x = <800>; + touchscreen-size-y = <480>; + touchscreen-fuzz-x = <4>; + touchscreen-fuzz-y = <7>; + + bootloader-key = /bits/ 8 <0x01 0x02 0x03 0x04 0x05 0x06 0x07 0x08>; + active-distance = <8>; + active-interval-ms = <0>; + lowpower-interval-ms = <200>; + touch-timeout-ms = <100>; + }; + + /* ... */ + }; diff --git a/Documentation/devicetree/bindings/input/touchscreen/fsl-mx25-tcq.txt b/Documentation/devicetree/bindings/input/touchscreen/fsl-mx25-tcq.txt new file mode 100644 index 0000000..cdf05f9 --- /dev/null +++ b/Documentation/devicetree/bindings/input/touchscreen/fsl-mx25-tcq.txt @@ -0,0 +1,35 @@ +Freescale mx25 TS conversion queue module + +mx25 touchscreen conversion queue module which controls the ADC unit of the +mx25 for attached touchscreens. + +Required properties: + - compatible: Should be "fsl,imx25-tcq". + - reg: Memory range of the device. + - interrupts: Should be the interrupt number associated with this module within + the tscadc unit (<0>). + - interrupt-parent: Should be a phandle to the tscadc unit. + - fsl,wires: Should be '<4>' or '<5>' + +Optional properties: + - fsl,pen-debounce-ns: Pen debounce time in nanoseconds. + - fsl,pen-threshold: Pen-down threshold for the touchscreen. This is a value + between 1 and 4096. It is the ratio between the internal reference voltage + and the measured voltage after the plate was precharged. Resistence between + plates and therefore the voltage decreases with pressure so that a smaller + value is equivalent to a higher pressure. + - fsl,settling-time-ns: Settling time in nanoseconds. The settling time is before + the actual touch detection to wait for an even charge distribution in the + plate. + +This device includes two conversion queues which can be added as subnodes. +The first queue is for the touchscreen, the second for general purpose ADC. + +Example: + tsc: tcq@50030400 { + compatible = "fsl,imx25-tcq"; + reg = <0x50030400 0x60>; + interrupt-parent = <&tscadc>; + interrupts = <0>; + fsl,wires = <4>; + }; diff --git a/Documentation/devicetree/bindings/input/touchscreen/touchscreen.txt b/Documentation/devicetree/bindings/input/touchscreen/touchscreen.txt index ac23caf..bccaa4e 100644 --- a/Documentation/devicetree/bindings/input/touchscreen/touchscreen.txt +++ b/Documentation/devicetree/bindings/input/touchscreen/touchscreen.txt @@ -18,6 +18,8 @@ Optional properties for Touchscreens: - touchscreen-inverted-y : Y axis is inverted (boolean) - touchscreen-swapped-x-y : X and Y axis are swapped (boolean) Swapping is done after inverting the axis + - touchscreen-x-mm : horizontal length in mm of the touchscreen + - touchscreen-y-mm : vertical length in mm of the touchscreen Deprecated properties for Touchscreens: - x-size : deprecated name for touchscreen-size-x diff --git a/Documentation/devicetree/bindings/interrupt-controller/al,alpine-msix.txt b/Documentation/devicetree/bindings/interrupt-controller/al,alpine-msix.txt new file mode 100644 index 0000000..f6f1c14 --- /dev/null +++ b/Documentation/devicetree/bindings/interrupt-controller/al,alpine-msix.txt @@ -0,0 +1,26 @@ +Alpine MSIX controller + +See arm,gic-v3.txt for SPI and MSI definitions. + +Required properties: + +- compatible: should be "al,alpine-msix" +- reg: physical base address and size of the registers +- interrupt-parent: specifies the parent interrupt controller. +- interrupt-controller: identifies the node as an interrupt controller +- msi-controller: identifies the node as an PCI Message Signaled Interrupt + controller +- al,msi-base-spi: SPI base of the MSI frame +- al,msi-num-spis: number of SPIs assigned to the MSI frame, relative to SPI0 + +Example: + +msix: msix { + compatible = "al,alpine-msix"; + reg = <0x0 0xfbe00000 0x0 0x100000>; + interrupt-parent = <&gic>; + interrupt-controller; + msi-controller; + al,msi-base-spi = <160>; + al,msi-num-spis = <160>; +}; diff --git a/Documentation/devicetree/bindings/interrupt-controller/arm,gic.txt b/Documentation/devicetree/bindings/interrupt-controller/arm,gic.txt index 5a1cb4b..793c20f 100644 --- a/Documentation/devicetree/bindings/interrupt-controller/arm,gic.txt +++ b/Documentation/devicetree/bindings/interrupt-controller/arm,gic.txt @@ -16,6 +16,7 @@ Main node required properties: "arm,cortex-a15-gic" "arm,cortex-a7-gic" "arm,cortex-a9-gic" + "arm,eb11mp-gic" "arm,gic-400" "arm,pl390" "arm,tc11mp-gic" diff --git a/Documentation/devicetree/bindings/interrupt-controller/hisilicon,mbigen-v2.txt b/Documentation/devicetree/bindings/interrupt-controller/hisilicon,mbigen-v2.txt index 720f7c9..3b2f4c4 100644 --- a/Documentation/devicetree/bindings/interrupt-controller/hisilicon,mbigen-v2.txt +++ b/Documentation/devicetree/bindings/interrupt-controller/hisilicon,mbigen-v2.txt @@ -21,6 +21,8 @@ Mbigen main node required properties: - reg: Specifies the base physical address and size of the Mbigen registers. +Mbigen sub node required properties: +------------------------------------------ - interrupt controller: Identifies the node as an interrupt controller - msi-parent: Specifies the MSI controller this mbigen use. @@ -45,13 +47,23 @@ Mbigen main node required properties: Examples: - mbigen_device_gmac:intc { + mbigen_chip_dsa { compatible = "hisilicon,mbigen-v2"; reg = <0x0 0xc0080000 0x0 0x10000>; - interrupt-controller; - msi-parent = <&its_dsa 0x40b1c>; - num-pins = <9>; - #interrupt-cells = <2>; + + mbigen_gmac:intc_gmac { + interrupt-controller; + msi-parent = <&its_dsa 0x40b1c>; + num-pins = <9>; + #interrupt-cells = <2>; + }; + + mbigen_i2c:intc_i2c { + interrupt-controller; + msi-parent = <&its_dsa 0x40b0e>; + num-pins = <2>; + #interrupt-cells = <2>; + }; }; Devices connect to mbigen required properties: diff --git a/Documentation/devicetree/bindings/interrupt-controller/marvell,odmi-controller.txt b/Documentation/devicetree/bindings/interrupt-controller/marvell,odmi-controller.txt new file mode 100644 index 0000000..8af0a8e --- /dev/null +++ b/Documentation/devicetree/bindings/interrupt-controller/marvell,odmi-controller.txt @@ -0,0 +1,44 @@ + +* Marvell ODMI for MSI support + +Some Marvell SoCs have an On-Die Message Interrupt (ODMI) controller +which can be used by on-board peripheral for MSI interrupts. + +Required properties: + +- compatible : The value here should contain: + + "marvell,ap806-odmi-controller", "marvell,odmi-controller". + +- interrupt,controller : Identifies the node as an interrupt controller. + +- msi-controller : Identifies the node as an MSI controller. + +- marvell,odmi-frames : Number of ODMI frames available. Each frame + provides a number of events. + +- reg : List of register definitions, one for each + ODMI frame. + +- marvell,spi-base : List of GIC base SPI interrupts, one for each + ODMI frame. Those SPI interrupts are 0-based, + i.e marvell,spi-base = <128> will use SPI #96. + See Documentation/devicetree/bindings/interrupt-controller/arm,gic.txt + for details about the GIC Device Tree binding. + +- interrupt-parent : Reference to the parent interrupt controller. + +Example: + + odmi: odmi@300000 { + compatible = "marvell,ap806-odm-controller", + "marvell,odmi-controller"; + interrupt-controller; + msi-controller; + marvell,odmi-frames = <4>; + reg = <0x300000 0x4000>, + <0x304000 0x4000>, + <0x308000 0x4000>, + <0x30C000 0x4000>; + marvell,spi-base = <128>, <136>, <144>, <152>; + }; diff --git a/Documentation/devicetree/bindings/interrupt-controller/mips-gic.txt b/Documentation/devicetree/bindings/interrupt-controller/mips-gic.txt index aae4c38..1735953 100644 --- a/Documentation/devicetree/bindings/interrupt-controller/mips-gic.txt +++ b/Documentation/devicetree/bindings/interrupt-controller/mips-gic.txt @@ -23,6 +23,12 @@ Optional properties: - mti,reserved-cpu-vectors : Specifies the list of CPU interrupt vectors to which the GIC may not route interrupts. Valid values are 2 - 7. This property is ignored if the CPU is started in EIC mode. +- mti,reserved-ipi-vectors : Specifies the range of GIC interrupts that are + reserved for IPIs. + It accepts 2 values, the 1st is the starting interrupt and the 2nd is the size + of the reserved range. + If not specified, the driver will allocate the last 2 * number of VPEs in the + system. Required properties for timer sub-node: - compatible : Should be "mti,gic-timer". @@ -44,6 +50,7 @@ Example: #interrupt-cells = <3>; mti,reserved-cpu-vectors = <7>; + mti,reserved-ipi-vectors = <40 8>; timer { compatible = "mti,gic-timer"; diff --git a/Documentation/devicetree/bindings/interrupt-controller/sigma,smp8642-intc.txt b/Documentation/devicetree/bindings/interrupt-controller/sigma,smp8642-intc.txt new file mode 100644 index 0000000..1f441fa --- /dev/null +++ b/Documentation/devicetree/bindings/interrupt-controller/sigma,smp8642-intc.txt @@ -0,0 +1,49 @@ +Sigma Designs SMP86xx/SMP87xx secondary interrupt controller + +Required properties: +- compatible: should be "sigma,smp8642-intc" +- reg: physical address of MMIO region +- ranges: address space mapping of child nodes +- interrupt-parent: phandle of parent interrupt controller +- interrupt-controller: boolean +- #address-cells: should be <1> +- #size-cells: should be <1> + +One child node per control block with properties: +- reg: address of registers for this control block +- interrupt-controller: boolean +- #interrupt-cells: should be <2>, interrupt index and flags per interrupts.txt +- interrupts: interrupt spec of primary interrupt controller + +Example: + +interrupt-controller@6e000 { + compatible = "sigma,smp8642-intc"; + reg = <0x6e000 0x400>; + ranges = <0x0 0x6e000 0x400>; + interrupt-parent = <&gic>; + interrupt-controller; + #address-cells = <1>; + #size-cells = <1>; + + irq0: interrupt-controller@0 { + reg = <0x000 0x100>; + interrupt-controller; + #interrupt-cells = <2>; + interrupts = <GIC_SPI 2 IRQ_TYPE_LEVEL_HIGH>; + }; + + irq1: interrupt-controller@100 { + reg = <0x100 0x100>; + interrupt-controller; + #interrupt-cells = <2>; + interrupts = <GIC_SPI 3 IRQ_TYPE_LEVEL_HIGH>; + }; + + irq2: interrupt-controller@300 { + reg = <0x300 0x100>; + interrupt-controller; + #interrupt-cells = <2>; + interrupts = <GIC_SPI 4 IRQ_TYPE_LEVEL_HIGH>; + }; +}; diff --git a/Documentation/devicetree/bindings/iommu/mediatek,iommu.txt b/Documentation/devicetree/bindings/iommu/mediatek,iommu.txt new file mode 100644 index 0000000..cd1b1cd --- /dev/null +++ b/Documentation/devicetree/bindings/iommu/mediatek,iommu.txt @@ -0,0 +1,68 @@ +* Mediatek IOMMU Architecture Implementation + + Some Mediatek SOCs contain a Multimedia Memory Management Unit (M4U) which +uses the ARM Short-Descriptor translation table format for address translation. + + About the M4U Hardware Block Diagram, please check below: + + EMI (External Memory Interface) + | + m4u (Multimedia Memory Management Unit) + | + SMI Common(Smart Multimedia Interface Common) + | + +----------------+------- + | | + | | + SMI larb0 SMI larb1 ... SoCs have several SMI local arbiter(larb). + (display) (vdec) + | | + | | + +-----+-----+ +----+----+ + | | | | | | + | | |... | | | ... There are different ports in each larb. + | | | | | | +OVL0 RDMA0 WDMA0 MC PP VLD + + As above, The Multimedia HW will go through SMI and M4U while it +access EMI. SMI is a bridge between m4u and the Multimedia HW. It contain +smi local arbiter and smi common. It will control whether the Multimedia +HW should go though the m4u for translation or bypass it and talk +directly with EMI. And also SMI help control the power domain and clocks for +each local arbiter. + Normally we specify a local arbiter(larb) for each multimedia HW +like display, video decode, and camera. And there are different ports +in each larb. Take a example, There are many ports like MC, PP, VLD in the +video decode local arbiter, all these ports are according to the video HW. + +Required properties: +- compatible : must be "mediatek,mt8173-m4u". +- reg : m4u register base and size. +- interrupts : the interrupt of m4u. +- clocks : must contain one entry for each clock-names. +- clock-names : must be "bclk", It is the block clock of m4u. +- mediatek,larbs : List of phandle to the local arbiters in the current Socs. + Refer to bindings/memory-controllers/mediatek,smi-larb.txt. It must sort + according to the local arbiter index, like larb0, larb1, larb2... +- iommu-cells : must be 1. This is the mtk_m4u_id according to the HW. + Specifies the mtk_m4u_id as defined in + dt-binding/memory/mt8173-larb-port.h. + +Example: + iommu: iommu@10205000 { + compatible = "mediatek,mt8173-m4u"; + reg = <0 0x10205000 0 0x1000>; + interrupts = <GIC_SPI 139 IRQ_TYPE_LEVEL_LOW>; + clocks = <&infracfg CLK_INFRA_M4U>; + clock-names = "bclk"; + mediatek,larbs = <&larb0 &larb1 &larb2 &larb3 &larb4 &larb5>; + #iommu-cells = <1>; + }; + +Example for a client device: + display { + compatible = "mediatek,mt8173-disp"; + iommus = <&iommu M4U_PORT_DISP_OVL0>, + <&iommu M4U_PORT_DISP_RDMA0>; + ... + }; diff --git a/Documentation/devicetree/bindings/iommu/renesas,ipmmu-vmsa.txt b/Documentation/devicetree/bindings/iommu/renesas,ipmmu-vmsa.txt index 48ffb38..3ed027c 100644 --- a/Documentation/devicetree/bindings/iommu/renesas,ipmmu-vmsa.txt +++ b/Documentation/devicetree/bindings/iommu/renesas,ipmmu-vmsa.txt @@ -7,23 +7,34 @@ connected to the IPMMU through a port called micro-TLB. Required Properties: - - compatible: Must contain SoC-specific and generic entries from below. + - compatible: Must contain SoC-specific and generic entry below in case + the device is compatible with the R-Car Gen2 VMSA-compatible IPMMU. - "renesas,ipmmu-r8a73a4" for the R8A73A4 (R-Mobile APE6) IPMMU. - "renesas,ipmmu-r8a7790" for the R8A7790 (R-Car H2) IPMMU. - "renesas,ipmmu-r8a7791" for the R8A7791 (R-Car M2-W) IPMMU. - "renesas,ipmmu-r8a7793" for the R8A7793 (R-Car M2-N) IPMMU. - "renesas,ipmmu-r8a7794" for the R8A7794 (R-Car E2) IPMMU. + - "renesas,ipmmu-r8a7795" for the R8A7795 (R-Car H3) IPMMU. - "renesas,ipmmu-vmsa" for generic R-Car Gen2 VMSA-compatible IPMMU. - reg: Base address and size of the IPMMU registers. - interrupts: Specifiers for the MMU fault interrupts. For instances that support secure mode two interrupts must be specified, for non-secure and secure mode, in that order. For instances that don't support secure mode a - single interrupt must be specified. + single interrupt must be specified. Not required for cache IPMMUs. - #iommu-cells: Must be 1. +Optional properties: + + - renesas,ipmmu-main: reference to the main IPMMU instance in two cells. + The first cell is a phandle to the main IPMMU and the second cell is + the interrupt bit number associated with the particular cache IPMMU device. + The interrupt bit number needs to match the main IPMMU IMSSTR register. + Only used by cache IPMMU instances. + + Each bus master connected to an IPMMU must reference the IPMMU in its device node with the following property: diff --git a/Documentation/devicetree/bindings/iommu/samsung,sysmmu.txt b/Documentation/devicetree/bindings/iommu/samsung,sysmmu.txt index bc620fe..85f0688 100644 --- a/Documentation/devicetree/bindings/iommu/samsung,sysmmu.txt +++ b/Documentation/devicetree/bindings/iommu/samsung,sysmmu.txt @@ -23,28 +23,24 @@ MMUs. for window 1, 2 and 3. * M2M Scalers and G2D in Exynos5420 has one System MMU on the read channel and the other System MMU on the write channel. -The drivers must consider how to handle those System MMUs. One of the idea is -to implement child devices or sub-devices which are the client devices of the -System MMU. -Note: -The current DT binding for the Exynos System MMU is incomplete. -The following properties can be removed or changed, if found incompatible with -the "Generic IOMMU Binding" support for attaching devices to the IOMMU. +For information on assigning System MMU controller to its peripheral devices, +see generic IOMMU bindings. Required properties: - compatible: Should be "samsung,exynos-sysmmu" - reg: A tuple of base address and size of System MMU registers. +- #iommu-cells: Should be <0>. - interrupt-parent: The phandle of the interrupt controller of System MMU - interrupts: An interrupt specifier for interrupt signal of System MMU, according to the format defined by a particular interrupt controller. -- clock-names: Should be "sysmmu" if the System MMU is needed to gate its clock. +- clock-names: Should be "sysmmu" or a pair of "aclk" and "pclk" to gate + SYSMMU core clocks. Optional "master" if the clock to the System MMU is gated by - another gate clock other than "sysmmu". - Exynos4 SoCs, there needs no "master" clock. - Exynos5 SoCs, some System MMUs must have "master" clocks. -- clocks: Required if the System MMU is needed to gate its clock. + another gate clock other core (usually main gate clock + of peripheral device this SYSMMU belongs to). +- clocks: Phandles for respective clocks described by clock-names. - power-domains: Required if the System MMU is needed to gate its power. Please refer to the following document: Documentation/devicetree/bindings/power/pd-samsung.txt @@ -57,6 +53,7 @@ Examples: power-domains = <&pd_gsc>; clocks = <&clock CLK_GSCL0>; clock-names = "gscl"; + iommus = <&sysmmu_gsc0>; }; sysmmu_gsc0: sysmmu@13E80000 { @@ -67,4 +64,5 @@ Examples: clock-names = "sysmmu", "master"; clocks = <&clock CLK_SMMU_GSCL0>, <&clock CLK_GSCL0>; power-domains = <&pd_gsc>; + #iommu-cells = <0>; }; diff --git a/Documentation/devicetree/bindings/leds/leds-is31fl32xx.txt b/Documentation/devicetree/bindings/leds/leds-is31fl32xx.txt new file mode 100644 index 0000000..926c211 --- /dev/null +++ b/Documentation/devicetree/bindings/leds/leds-is31fl32xx.txt @@ -0,0 +1,52 @@ +Binding for ISSI IS31FL32xx and Si-En SN32xx LED Drivers + +The IS31FL32xx/SN32xx family of LED drivers are I2C devices with multiple +constant-current channels, each with independent 256-level PWM control. +Each LED is represented as a sub-node of the device. + +Required properties: +- compatible: one of + issi,is31fl3236 + issi,is31fl3235 + issi,is31fl3218 + issi,is31fl3216 + si-en,sn3218 + si-en,sn3216 +- reg: I2C slave address +- address-cells : must be 1 +- size-cells : must be 0 + +LED sub-node properties: +- reg : LED channel number (1..N) +- label : (optional) + see Documentation/devicetree/bindings/leds/common.txt +- linux,default-trigger : (optional) + see Documentation/devicetree/bindings/leds/common.txt + + +Example: + +is31fl3236: led-controller@3c { + compatible = "issi,is31fl3236"; + reg = <0x3c>; + #address-cells = <1>; + #size-cells = <0>; + + led@1 { + reg = <1>; + label = "EB:blue:usr0"; + }; + led@2 { + reg = <2>; + label = "EB:blue:usr1"; + }; + ... + led@36 { + reg = <36>; + label = "EB:blue:usr35"; + }; +}; + +For more product information please see the links below: +http://www.issi.com/US/product-analog-fxled-driver.shtml +http://www.si-en.com/product.asp?parentid=890 diff --git a/Documentation/devicetree/bindings/mailbox/hisilicon,hi6220-mailbox.txt b/Documentation/devicetree/bindings/mailbox/hisilicon,hi6220-mailbox.txt new file mode 100644 index 0000000..044b17f --- /dev/null +++ b/Documentation/devicetree/bindings/mailbox/hisilicon,hi6220-mailbox.txt @@ -0,0 +1,74 @@ +Hisilicon Hi6220 Mailbox Driver +=============================== + +Hisilicon Hi6220 mailbox supports up to 32 channels. Each channel +is unidirectional with a maximum message size of 8 words. I/O is +performed using register access (there is no DMA) and the cell +raises an interrupt when messages are received. + +Mailbox Device Node: +==================== + +Required properties: +-------------------- +- compatible: Shall be "hisilicon,hi6220-mbox" +- reg: Contains the mailbox register address range (base + address and length); the first item is for IPC + registers, the second item is shared buffer for + slots. +- #mbox-cells: Common mailbox binding property to identify the number + of cells required for the mailbox specifier. Must be 3. + <&phandle slot_id dst_irq ack_irq> + phandle: Label name of mailbox controller + slot_id: Slot id used either for TX or RX + dst_irq: IRQ identifier index number which used by MCU + ack_irq: IRQ identifier index number with generating a + TX/RX interrupt to application processor, + mailbox driver uses it to acknowledge interrupt +- interrupts: Contains the interrupt information for the mailbox + device. The format is dependent on which interrupt + controller the SoCs use. + +Optional Properties: +-------------------- +- hi6220,mbox-tx-noirq: Property of MCU firmware's feature, so mailbox driver + use this flag to ask MCU to enable "automatic idle + flag" mode or IRQ generated mode to acknowledge a TX + completion. + +Example: +-------- + + mailbox: mailbox@f7510000 { + compatible = "hisilicon,hi6220-mbox"; + reg = <0x0 0xf7510000 0x0 0x1000>, /* IPC_S */ + <0x0 0x06dff800 0x0 0x0800>; /* Mailbox */ + interrupt-parent = <&gic>; + interrupts = <GIC_SPI 94 IRQ_TYPE_LEVEL_HIGH>; + #mbox-cells = <3>; + }; + + +Mailbox client +=============== + +Required properties: +-------------------- +- compatible: Many (See the client docs). +- mboxes: Standard property to specify a Mailbox (See ./mailbox.txt) + Cells must match 'mbox-cells' (See Mailbox Device Node above). + +Optional Properties: +-------------------- +- mbox-names: Name given to channels seen in the 'mboxes' property. + +Example: +-------- + + stub_clock: stub_clock { + compatible = "hisilicon,hi6220-stub-clk"; + hisilicon,hi6220-clk-sram = <&sram>; + #clock-cells = <1>; + mbox-names = "mbox-tx", "mbox-rx"; + mboxes = <&mailbox 1 0 11>, <&mailbox 0 1 10>; + }; diff --git a/Documentation/devicetree/bindings/mailbox/rockchip-mailbox.txt b/Documentation/devicetree/bindings/mailbox/rockchip-mailbox.txt new file mode 100644 index 0000000..b6bb84a --- /dev/null +++ b/Documentation/devicetree/bindings/mailbox/rockchip-mailbox.txt @@ -0,0 +1,32 @@ +Rockchip mailbox + +The Rockchip mailbox is used by the Rockchip CPU cores to communicate +requests to MCU processor. + +Refer to ./mailbox.txt for generic information about mailbox device-tree +bindings. + +Required properties: + + - compatible: should be one of the following. + - "rockchip,rk3368-mbox" for rk3368 + - reg: physical base address of the controller and length of memory mapped + region. + - interrupts: The interrupt number to the cpu. The interrupt specifier format + depends on the interrupt controller. + - #mbox-cells: Common mailbox binding property to identify the number + of cells required for the mailbox specifier. Should be 1 + +Example: +-------- + +/* RK3368 */ +mbox: mbox@ff6b0000 { + compatible = "rockchip,rk3368-mailbox"; + reg = <0x0 0xff6b0000 0x0 0x1000>, + interrupts = <GIC_SPI 146 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 147 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 148 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 149 IRQ_TYPE_LEVEL_HIGH>; + #mbox-cells = <1>; +}; diff --git a/Documentation/devicetree/bindings/mailbox/sti-mailbox.txt b/Documentation/devicetree/bindings/mailbox/sti-mailbox.txt index b61eec9..351f612 100644 --- a/Documentation/devicetree/bindings/mailbox/sti-mailbox.txt +++ b/Documentation/devicetree/bindings/mailbox/sti-mailbox.txt @@ -44,7 +44,7 @@ Optional properties Example: mailbox_test { - compatible = "mailbox_test"; + compatible = "mailbox-test"; reg = <0x[shared_memory_address], [shared_memory_size]>; mboxes = <&mailbox2 0 1>, <&mailbox0 2 1>; mbox-names = "tx", "rx"; diff --git a/Documentation/devicetree/bindings/mailbox/ti,message-manager.txt b/Documentation/devicetree/bindings/mailbox/ti,message-manager.txt new file mode 100644 index 0000000..b449d02 --- /dev/null +++ b/Documentation/devicetree/bindings/mailbox/ti,message-manager.txt @@ -0,0 +1,50 @@ +Texas Instruments' Message Manager Driver +======================================== + +The Texas Instruments' Message Manager is a mailbox controller that has +configurable queues selectable at SoC(System on Chip) integration. The Message +manager is broken up into queues in different address regions that are called +"proxies" - each instance is unidirectional and is instantiated at SoC +integration level to indicate receive or transmit path. + +Message Manager Device Node: +=========================== +Required properties: +-------------------- +- compatible: Shall be: "ti,k2g-message-manager" +- reg-names queue_proxy_region - Map the queue proxy region. + queue_state_debug_region - Map the queue state debug + region. +- reg: Contains the register map per reg-names. +- #mbox-cells Shall be 2. Contains the queue ID and proxy ID in that + order referring to the transfer path. +- interrupt-names: Contains interrupt names matching the rx transfer path + for a given SoC. Receive interrupts shall be of the + format: "rx_<QID>_<PID>". + For ti,k2g-message-manager, this shall contain: + "rx_005_002", "rx_057_002" +- interrupts: Contains the interrupt information corresponding to + interrupt-names property. + +Example(K2G): +------------ + + msgmgr: msgmgr@02a00000 { + compatible = "ti,k2g-message-manager"; + #mbox-cells = <2>; + reg-names = "queue_proxy_region", "queue_state_debug_region"; + reg = <0x02a00000 0x400000>, <0x028c3400 0x400>; + interrupt-names = "rx_005", "rx_057"; + interrupts = <GIC_SPI 324 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 327 IRQ_TYPE_LEVEL_HIGH>; + }; + + pmmc: pmmc { + [...] + mbox-names = "rx", "tx"; + # RX queue ID is 5, proxy ID is 2 + # TX queue ID is 0, proxy ID is 0 + mboxes= <&msgmgr 5 2>, + <&msgmgr 0 0>; + [...] + }; diff --git a/Documentation/devicetree/bindings/mailbox/xgene-slimpro-mailbox.txt b/Documentation/devicetree/bindings/mailbox/xgene-slimpro-mailbox.txt new file mode 100644 index 0000000..e46451b --- /dev/null +++ b/Documentation/devicetree/bindings/mailbox/xgene-slimpro-mailbox.txt @@ -0,0 +1,35 @@ +The APM X-Gene SLIMpro mailbox is used to communicate messages between +the ARM64 processors and the Cortex M3 (dubbed SLIMpro). It uses a simple +interrupt based door bell mechanism and can exchange simple messages using the +internal registers. + +There are total of 8 interrupts in this mailbox. Each used for an individual +door bell (or mailbox channel). + +Required properties: +- compatible: Should be as "apm,xgene-slimpro-mbox". + +- reg: Contains the mailbox register address range. + +- interrupts: 8 interrupts must be from 0 to 7, interrupt 0 define the + the interrupt for mailbox channel 0 and interrupt 1 for + mailbox channel 1 and so likewise for the reminder. + +- #mbox-cells: only one to specify the mailbox channel number. + +Example: + +Mailbox Node: + mailbox: mailbox@10540000 { + compatible = "apm,xgene-slimpro-mbox"; + reg = <0x0 0x10540000 0x0 0xa000>; + #mbox-cells = <1>; + interrupts = <0x0 0x0 0x4>, + <0x0 0x1 0x4>, + <0x0 0x2 0x4>, + <0x0 0x3 0x4>, + <0x0 0x4 0x4>, + <0x0 0x5 0x4>, + <0x0 0x6 0x4>, + <0x0 0x7 0x4>, + }; diff --git a/Documentation/devicetree/bindings/media/i2c/mt9v032.txt b/Documentation/devicetree/bindings/media/i2c/mt9v032.txt index 2025653..100f0ae 100644 --- a/Documentation/devicetree/bindings/media/i2c/mt9v032.txt +++ b/Documentation/devicetree/bindings/media/i2c/mt9v032.txt @@ -20,6 +20,8 @@ Optional Properties: - link-frequencies: List of allowed link frequencies in Hz. Each frequency is expressed as a 64-bit big-endian integer. +- reset-gpios: GPIO handle which is connected to the reset pin of the chip. +- standby-gpios: GPIO handle which is connected to the standby pin of the chip. For further reading on port node refer to Documentation/devicetree/bindings/media/video-interfaces.txt. diff --git a/Documentation/devicetree/bindings/media/i2c/tvp5150.txt b/Documentation/devicetree/bindings/media/i2c/tvp5150.txt new file mode 100644 index 0000000..8c0fc1a --- /dev/null +++ b/Documentation/devicetree/bindings/media/i2c/tvp5150.txt @@ -0,0 +1,45 @@ +* Texas Instruments TVP5150 and TVP5151 video decoders + +The TVP5150 and TVP5151 are video decoders that convert baseband NTSC and PAL +(and also SECAM in the TVP5151 case) video signals to either 8-bit 4:2:2 YUV +with discrete syncs or 8-bit ITU-R BT.656 with embedded syncs output formats. + +Required Properties: +- compatible: value must be "ti,tvp5150" +- reg: I2C slave address + +Optional Properties: +- pdn-gpios: phandle for the GPIO connected to the PDN pin, if any. +- reset-gpios: phandle for the GPIO connected to the RESETB pin, if any. + +The device node must contain one 'port' child node for its digital output +video port, in accordance with the video interface bindings defined in +Documentation/devicetree/bindings/media/video-interfaces.txt. + +Required Endpoint Properties for parallel synchronization: + +- hsync-active: active state of the HSYNC signal. Must be <1> (HIGH). +- vsync-active: active state of the VSYNC signal. Must be <1> (HIGH). +- field-even-active: field signal level during the even field data + transmission. Must be <0>. + +If none of hsync-active, vsync-active and field-even-active is specified, +the endpoint is assumed to use embedded BT.656 synchronization. + +Example: + +&i2c2 { + ... + tvp5150@5c { + compatible = "ti,tvp5150"; + reg = <0x5c>; + pdn-gpios = <&gpio4 30 GPIO_ACTIVE_LOW>; + reset-gpios = <&gpio6 7 GPIO_ACTIVE_LOW>; + + port { + tvp5150_1: endpoint { + remote-endpoint = <&ccdc_ep>; + }; + }; + }; +}; diff --git a/Documentation/devicetree/bindings/media/rcar_vin.txt b/Documentation/devicetree/bindings/media/rcar_vin.txt index 9dafe6b..619193c 100644 --- a/Documentation/devicetree/bindings/media/rcar_vin.txt +++ b/Documentation/devicetree/bindings/media/rcar_vin.txt @@ -6,6 +6,7 @@ family of devices. The current blocks are always slaves and suppot one input channel which can be either RGB, YUYV or BT656. - compatible: Must be one of the following + - "renesas,vin-r8a7795" for the R8A7795 device - "renesas,vin-r8a7794" for the R8A7794 device - "renesas,vin-r8a7793" for the R8A7793 device - "renesas,vin-r8a7791" for the R8A7791 device diff --git a/Documentation/devicetree/bindings/media/renesas,jpu.txt b/Documentation/devicetree/bindings/media/renesas,jpu.txt index 0cb9420..d3436e5 100644 --- a/Documentation/devicetree/bindings/media/renesas,jpu.txt +++ b/Documentation/devicetree/bindings/media/renesas,jpu.txt @@ -5,11 +5,12 @@ and decoding function conforming to the JPEG baseline process, so that the JPU can encode image data and decode JPEG data quickly. Required properties: - - compatible: should containg one of the following: - - "renesas,jpu-r8a7790" for R-Car H2 - - "renesas,jpu-r8a7791" for R-Car M2-W - - "renesas,jpu-r8a7792" for R-Car V2H - - "renesas,jpu-r8a7793" for R-Car M2-N +- compatible: "renesas,jpu-<soctype>", "renesas,rcar-gen2-jpu" as fallback. + Examples with soctypes are: + - "renesas,jpu-r8a7790" for R-Car H2 + - "renesas,jpu-r8a7791" for R-Car M2-W + - "renesas,jpu-r8a7792" for R-Car V2H + - "renesas,jpu-r8a7793" for R-Car M2-N - reg: Base address and length of the registers block for the JPU. - interrupts: JPU interrupt specifier. @@ -17,7 +18,7 @@ Required properties: Example: R8A7790 (R-Car H2) JPU node jpeg-codec@fe980000 { - compatible = "renesas,jpu-r8a7790"; + compatible = "renesas,jpu-r8a7790", "renesas,rcar-gen2-jpu"; reg = <0 0xfe980000 0 0x10300>; interrupts = <0 272 IRQ_TYPE_LEVEL_HIGH>; clocks = <&mstp1_clks R8A7790_CLK_JPU>; diff --git a/Documentation/devicetree/bindings/media/renesas,vsp1.txt b/Documentation/devicetree/bindings/media/renesas,vsp1.txt index 87fe08a..627405ab 100644 --- a/Documentation/devicetree/bindings/media/renesas,vsp1.txt +++ b/Documentation/devicetree/bindings/media/renesas,vsp1.txt @@ -1,30 +1,18 @@ -* Renesas VSP1 Video Processing Engine +* Renesas VSP Video Processing Engine -The VSP1 is a video processing engine that supports up-/down-scaling, alpha +The VSP is a video processing engine that supports up-/down-scaling, alpha blending, color space conversion and various other image processing features. It can be found in the Renesas R-Car second generation SoCs. Required properties: - - compatible: Must contain "renesas,vsp1" + - compatible: Must contain one of the following values + - "renesas,vsp1" for the R-Car Gen2 VSP1 + - "renesas,vsp2" for the R-Car Gen3 VSP2 - - reg: Base address and length of the registers block for the VSP1. - - interrupts: VSP1 interrupt specifier. - - clocks: A phandle + clock-specifier pair for the VSP1 functional clock. - - - renesas,#rpf: Number of Read Pixel Formatter (RPF) modules in the VSP1. - - renesas,#uds: Number of Up Down Scaler (UDS) modules in the VSP1. - - renesas,#wpf: Number of Write Pixel Formatter (WPF) modules in the VSP1. - - -Optional properties: - - - renesas,has-lif: Boolean, indicates that the LCD Interface (LIF) module is - available. - - renesas,has-lut: Boolean, indicates that the Look Up Table (LUT) module is - available. - - renesas,has-sru: Boolean, indicates that the Super Resolution Unit (SRU) - module is available. + - reg: Base address and length of the registers block for the VSP. + - interrupts: VSP interrupt specifier. + - clocks: A phandle + clock-specifier pair for the VSP functional clock. Example: R8A7790 (R-Car H2) VSP1-S node @@ -34,10 +22,4 @@ Example: R8A7790 (R-Car H2) VSP1-S node reg = <0 0xfe928000 0 0x8000>; interrupts = <0 267 IRQ_TYPE_LEVEL_HIGH>; clocks = <&mstp1_clks R8A7790_CLK_VSP1_S>; - - renesas,has-lut; - renesas,has-sru; - renesas,#rpf = <5>; - renesas,#uds = <3>; - renesas,#wpf = <4>; }; diff --git a/Documentation/devicetree/bindings/media/ti-cal.txt b/Documentation/devicetree/bindings/media/ti-cal.txt new file mode 100644 index 0000000..ae9b52f --- /dev/null +++ b/Documentation/devicetree/bindings/media/ti-cal.txt @@ -0,0 +1,72 @@ +Texas Instruments DRA72x CAMERA ADAPTATION LAYER (CAL) +------------------------------------------------------ + +The Camera Adaptation Layer (CAL) is a key component for image capture +applications. The capture module provides the system interface and the +processing capability to connect CSI2 image-sensor modules to the +DRA72x device. + +Required properties: +- compatible: must be "ti,dra72-cal" +- reg: CAL Top level, Receiver Core #0, Receiver Core #1 and Camera RX + control address space +- reg-names: cal_top, cal_rx_core0, cal_rx_core1, and camerrx_control + registers +- interrupts: should contain IRQ line for the CAL; + +CAL supports 2 camera port nodes on MIPI bus. Each CSI2 camera port nodes +should contain a 'port' child node with child 'endpoint' node. Please +refer to the bindings defined in +Documentation/devicetree/bindings/media/video-interfaces.txt. + +Example: + cal: cal@4845b000 { + compatible = "ti,dra72-cal"; + ti,hwmods = "cal"; + reg = <0x4845B000 0x400>, + <0x4845B800 0x40>, + <0x4845B900 0x40>, + <0x4A002e94 0x4>; + reg-names = "cal_top", + "cal_rx_core0", + "cal_rx_core1", + "camerrx_control"; + interrupts = <GIC_SPI 119 IRQ_TYPE_LEVEL_HIGH>; + #address-cells = <1>; + #size-cells = <0>; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + csi2_0: port@0 { + reg = <0>; + endpoint { + slave-mode; + remote-endpoint = <&ar0330_1>; + }; + }; + csi2_1: port@1 { + reg = <1>; + }; + }; + }; + + i2c5: i2c@4807c000 { + ar0330@10 { + compatible = "ti,ar0330"; + reg = <0x10>; + + port { + #address-cells = <1>; + #size-cells = <0>; + + ar0330_1: endpoint { + reg = <0>; + clock-lanes = <1>; + data-lanes = <0 2 3 4>; + remote-endpoint = <&csi2_0>; + }; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/memory-controllers/mediatek,smi-common.txt b/Documentation/devicetree/bindings/memory-controllers/mediatek,smi-common.txt new file mode 100644 index 0000000..06a83ce --- /dev/null +++ b/Documentation/devicetree/bindings/memory-controllers/mediatek,smi-common.txt @@ -0,0 +1,24 @@ +SMI (Smart Multimedia Interface) Common + +The hardware block diagram please check bindings/iommu/mediatek,iommu.txt + +Required properties: +- compatible : must be "mediatek,mt8173-smi-common" +- reg : the register and size of the SMI block. +- power-domains : a phandle to the power domain of this local arbiter. +- clocks : Must contain an entry for each entry in clock-names. +- clock-names : must contain 2 entries, as follows: + - "apb" : Advanced Peripheral Bus clock, It's the clock for setting + the register. + - "smi" : It's the clock for transfer data and command. + They may be the same if both source clocks are the same. + +Example: + smi_common: smi@14022000 { + compatible = "mediatek,mt8173-smi-common"; + reg = <0 0x14022000 0 0x1000>; + power-domains = <&scpsys MT8173_POWER_DOMAIN_MM>; + clocks = <&mmsys CLK_MM_SMI_COMMON>, + <&mmsys CLK_MM_SMI_COMMON>; + clock-names = "apb", "smi"; + }; diff --git a/Documentation/devicetree/bindings/memory-controllers/mediatek,smi-larb.txt b/Documentation/devicetree/bindings/memory-controllers/mediatek,smi-larb.txt new file mode 100644 index 0000000..55ff3b7 --- /dev/null +++ b/Documentation/devicetree/bindings/memory-controllers/mediatek,smi-larb.txt @@ -0,0 +1,25 @@ +SMI (Smart Multimedia Interface) Local Arbiter + +The hardware block diagram please check bindings/iommu/mediatek,iommu.txt + +Required properties: +- compatible : must be "mediatek,mt8173-smi-larb" +- reg : the register and size of this local arbiter. +- mediatek,smi : a phandle to the smi_common node. +- power-domains : a phandle to the power domain of this local arbiter. +- clocks : Must contain an entry for each entry in clock-names. +- clock-names: must contain 2 entries, as follows: + - "apb" : Advanced Peripheral Bus clock, It's the clock for setting + the register. + - "smi" : It's the clock for transfer data and command. + +Example: + larb1: larb@16010000 { + compatible = "mediatek,mt8173-smi-larb"; + reg = <0 0x16010000 0 0x1000>; + mediatek,smi = <&smi_common>; + power-domains = <&scpsys MT8173_POWER_DOMAIN_VDEC>; + clocks = <&vdecsys CLK_VDEC_CKEN>, + <&vdecsys CLK_VDEC_LARB_CKEN>; + clock-names = "apb", "smi"; + }; diff --git a/Documentation/devicetree/bindings/mfd/act8945a.txt b/Documentation/devicetree/bindings/mfd/act8945a.txt new file mode 100644 index 0000000..f712830 --- /dev/null +++ b/Documentation/devicetree/bindings/mfd/act8945a.txt @@ -0,0 +1,76 @@ +Device-Tree bindings for Active-semi ACT8945A MFD driver + +Required properties: + - compatible: "active-semi,act8945a". + - reg: the I2C slave address for the ACT8945A chip + +The chip exposes two subdevices: + - a regulators: see ../regulator/act8945a-regulator.txt + - a charger: see ../power/act8945a-charger.txt + +Example: + pmic@5b { + compatible = "active-semi,act8945a"; + reg = <0x5b>; + status = "okay"; + + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_charger_chglev>; + active-semi,chglev-gpio = <&pioA 12 GPIO_ACTIVE_HIGH>; + active-semi,input-voltage-threshold-microvolt = <6600>; + active-semi,precondition-timeout = <40>; + active-semi,total-timeout = <3>; + + active-semi,vsel-high; + + regulators { + vdd_1v35_reg: REG_DCDC1 { + regulator-name = "VDD_1V35"; + regulator-min-microvolt = <1350000>; + regulator-max-microvolt = <1350000>; + regulator-always-on; + }; + + vdd_1v2_reg: REG_DCDC2 { + regulator-name = "VDD_1V2"; + regulator-min-microvolt = <1100000>; + regulator-max-microvolt = <1300000>; + regulator-always-on; + }; + + vdd_3v3_reg: REG_DCDC3 { + regulator-name = "VDD_3V3"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-always-on; + }; + + vdd_fuse_reg: REG_LDO1 { + regulator-name = "VDD_FUSE"; + regulator-min-microvolt = <2500000>; + regulator-max-microvolt = <2500000>; + regulator-always-on; + }; + + vdd_3v3_lp_reg: REG_LDO2 { + regulator-name = "VDD_3V3_LP"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-always-on; + }; + + vdd_led_reg: REG_LDO3 { + regulator-name = "VDD_LED"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-always-on; + }; + + vdd_sdhc_1v8_reg: REG_LDO4 { + regulator-name = "VDD_SDHC_1V8"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-always-on; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/mfd/axp20x.txt b/Documentation/devicetree/bindings/mfd/axp20x.txt index a474359..fd39fa5 100644 --- a/Documentation/devicetree/bindings/mfd/axp20x.txt +++ b/Documentation/devicetree/bindings/mfd/axp20x.txt @@ -5,11 +5,12 @@ axp152 (X-Powers) axp202 (X-Powers) axp209 (X-Powers) axp221 (X-Powers) +axp223 (X-Powers) Required properties: - compatible: "x-powers,axp152", "x-powers,axp202", "x-powers,axp209", - "x-powers,axp221" -- reg: The I2C slave address for the AXP chip + "x-powers,axp221", "x-powers,axp223" +- reg: The I2C slave address or RSB hardware address for the AXP chip - interrupt-parent: The parent interrupt controller - interrupts: SoC NMI / GPIO interrupt connected to the PMIC's IRQ pin - interrupt-controller: The PMIC has its own internal IRQs @@ -51,7 +52,7 @@ LDO3 : LDO : ldo3in-supply LDO4 : LDO : ldo24in-supply : shared supply LDO5 : LDO : ldo5in-supply -AXP221 regulators, type, and corresponding input supply names: +AXP221/AXP223 regulators, type, and corresponding input supply names: Regulator Type Supply Name Notes --------- ---- ----------- ----- diff --git a/Documentation/devicetree/bindings/mfd/fsl-imx25-tsadc.txt b/Documentation/devicetree/bindings/mfd/fsl-imx25-tsadc.txt new file mode 100644 index 0000000..b035052 --- /dev/null +++ b/Documentation/devicetree/bindings/mfd/fsl-imx25-tsadc.txt @@ -0,0 +1,47 @@ +Freescale MX25 ADC/TSC MultiFunction Device (MFD) + +This device combines two general purpose conversion queues one used for general +ADC and the other used for touchscreens. + +Required properties: + - compatible: Should be "fsl,imx25-tsadc". + - reg: Start address and size of the memory area of + the device + - interrupts: Interrupt for this device + (See: ../interrupt-controller/interrupts.txt) + - clocks: An 'ipg' clock (See: ../clock/clock-bindings.txt) + - interrupt-controller: This device is an interrupt controller. It + controls the interrupts of both + conversion queues. + - #interrupt-cells: Should be '<1>'. + - #address-cells: Should be '<1>'. + - #size-cells: Should be '<1>'. + +This device includes two conversion queues which can be added as subnodes. +The first queue is for the touchscreen, the second for general purpose ADC. + +Example: + tscadc: tscadc@50030000 { + compatible = "fsl,imx25-tsadc"; + reg = <0x50030000 0xc>; + interrupts = <46>; + clocks = <&clks 119>; + clock-names = "ipg"; + interrupt-controller; + #interrupt-cells = <1>; + #address-cells = <1>; + #size-cells = <1>; + ranges; + + tsc: tcq@50030400 { + compatible = "fsl,imx25-tcq"; + reg = <0x50030400 0x60>; + ... + }; + + adc: gcq@50030800 { + compatible = "fsl,imx25-gcq"; + reg = <0x50030800 0x60>; + ... + }; + }; diff --git a/Documentation/devicetree/bindings/mfd/mt6397.txt b/Documentation/devicetree/bindings/mfd/mt6397.txt index 15043e6..949c85f 100644 --- a/Documentation/devicetree/bindings/mfd/mt6397.txt +++ b/Documentation/devicetree/bindings/mfd/mt6397.txt @@ -1,6 +1,6 @@ -MediaTek MT6397 Multifunction Device Driver +MediaTek MT6397/MT6323 Multifunction Device Driver -MT6397 is a multifunction device with the following sub modules: +MT6397/MT6323 is a multifunction device with the following sub modules: - Regulator - RTC - Audio codec @@ -8,14 +8,14 @@ MT6397 is a multifunction device with the following sub modules: - Clock It is interfaced to host controller using SPI interface by a proprietary hardware -called PMIC wrapper or pwrap. MT6397 MFD is a child device of pwrap. +called PMIC wrapper or pwrap. MT6397/MT6323 MFD is a child device of pwrap. See the following for pwarp node definitions: Documentation/devicetree/bindings/soc/pwrap.txt This document describes the binding for MFD device and its sub module. Required properties: -compatible: "mediatek,mt6397" +compatible: "mediatek,mt6397" or "mediatek,mt6323" Optional subnodes: @@ -26,6 +26,8 @@ Optional subnodes: Required properties: - compatible: "mediatek,mt6397-regulator" see Documentation/devicetree/bindings/regulator/mt6397-regulator.txt + - compatible: "mediatek,mt6323-regulator" + see Documentation/devicetree/bindings/regulator/mt6323-regulator.txt - codec Required properties: - compatible: "mediatek,mt6397-codec" diff --git a/Documentation/devicetree/bindings/mfd/tps65086.txt b/Documentation/devicetree/bindings/mfd/tps65086.txt new file mode 100644 index 0000000..d370561 --- /dev/null +++ b/Documentation/devicetree/bindings/mfd/tps65086.txt @@ -0,0 +1,55 @@ +* TPS65086 Power Management Integrated Circuit (PMIC) bindings + +Required properties: + - compatible : Should be "ti,tps65086". + - reg : I2C slave address. + - interrupt-parent : Phandle to the parent interrupt controller. + - interrupts : The interrupt line the device is connected to. + - interrupt-controller : Marks the device node as an interrupt controller. + - #interrupt-cells : The number of cells to describe an IRQ, should be 2. + The first cell is the IRQ number. + The second cell is the flags, encoded as trigger + masks from ../interrupt-controller/interrupts.txt. + - gpio-controller : Marks the device node as a GPIO Controller. + - #gpio-cells : Should be two. The first cell is the pin number and + the second cell is used to specify flags. + See ../gpio/gpio.txt for more information. + - regulators: : List of child nodes that specify the regulator + initialization data. Child nodes must be named + after their hardware counterparts: buck[1-6], + ldoa[1-3], swa1, swb[1-2], and vtt. Each child + node is defined using the standard binding for + regulators and the optional regulator properties + defined below. + +Optional regulator properties: + - ti,regulator-step-size-25mv : This is applicable for buck[1,2,6], set this + if the regulator is factory set with a 25mv + step voltage mapping. + - ti,regulator-decay : This is applicable for buck[1-6], set this if + the output needs to decay, default is for + the output to slew down. + +Example: + + pmic: tps65086@5e { + compatible = "ti,tps65086"; + reg = <0x5e>; + interrupt-parent = <&gpio1>; + interrupts = <28 IRQ_TYPE_LEVEL_LOW>; + interrupt-controller; + #interrupt-cells = <2>; + gpio-controller; + #gpio-cells = <2>; + + regulators { + buck1 { + regulator-name = "vcc1"; + regulator-min-microvolt = <1600000>; + regulator-max-microvolt = <1600000>; + regulator-boot-on; + ti,regulator-decay; + ti,regulator-step-size-25mv; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/mfd/tps65912.txt b/Documentation/devicetree/bindings/mfd/tps65912.txt new file mode 100644 index 0000000..717e66d --- /dev/null +++ b/Documentation/devicetree/bindings/mfd/tps65912.txt @@ -0,0 +1,50 @@ +* TPS65912 Power Management Integrated Circuit bindings + +Required properties: + - compatible : Should be "ti,tps65912". + - reg : Slave address or chip select number (I2C / SPI). + - interrupt-parent : The parent interrupt controller. + - interrupts : The interrupt line the device is connected to. + - interrupt-controller : Marks the device node as an interrupt controller. + - #interrupt-cells : The number of cells to describe an IRQ, should be 2. + The first cell is the IRQ number. + The second cell is the flags, encoded as trigger + masks from ../interrupt-controller/interrupts.txt. + - gpio-controller : Marks the device node as a GPIO Controller. + - #gpio-cells : Should be two. The first cell is the pin number and + the second cell is used to specify flags. + See ../gpio/gpio.txt for more information. + - regulators: : List of child nodes that specify the regulator + initialization data. Child nodes must be named + after their hardware counterparts: dcdc[1-4] and + ldo[1-10]. Each child nodes is defined using the + standard binding for regulators. + +Example: + + pmic: tps65912@2d { + compatible = "ti,tps65912"; + reg = <0x2d>; + interrupt-parent = <&gpio1>; + interrupts = <28 IRQ_TYPE_LEVEL_LOW>; + interrupt-controller; + #interrupt-cells = <2>; + gpio-controller; + #gpio-cells = <2>; + + regulators { + dcdc1 { + regulator-name = "vdd_core"; + regulator-min-microvolt = <912000>; + regulator-max-microvolt = <1144000>; + regulator-boot-on; + regulator-always-on; + }; + + ldo1 { + regulator-name = "ldo1"; + regulator-min-microvolt = <1900000>; + regulator-max-microvolt = <1900000>; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/mips/cavium/sata-uctl.txt b/Documentation/devicetree/bindings/mips/cavium/sata-uctl.txt new file mode 100644 index 0000000..3bd3c2f --- /dev/null +++ b/Documentation/devicetree/bindings/mips/cavium/sata-uctl.txt @@ -0,0 +1,42 @@ +* UCTL SATA controller glue + +UCTL is the bridge unit between the I/O interconnect (an internal bus) +and the SATA AHCI host controller (UAHC). It performs the following functions: + - provides interfaces for the applications to access the UAHC AHCI + registers on the CN71XX I/O space. + - provides a bridge for UAHC to fetch AHCI command table entries and data + buffers from Level 2 Cache. + - posts interrupts to the CIU. + - contains registers that: + - control the behavior of the UAHC + - control the clock/reset generation to UAHC + - control endian swapping for all UAHC registers and DMA accesses + +Properties: + +- compatible: "cavium,octeon-7130-sata-uctl" + + Compatibility with the cn7130 SOC. + +- reg: The base address of the UCTL register bank. + +- #address-cells, #size-cells, ranges and dma-ranges must be present and hold + suitable values to map all child nodes. + +Example: + + uctl@118006c000000 { + compatible = "cavium,octeon-7130-sata-uctl"; + reg = <0x11800 0x6c000000 0x0 0x100>; + ranges; /* Direct mapping */ + dma-ranges; + #address-cells = <2>; + #size-cells = <2>; + + sata: sata@16c0000000000 { + compatible = "cavium,octeon-7130-ahci"; + reg = <0x16c00 0x00000000 0x0 0x200>; + interrupt-parent = <&cibsata>; + interrupts = <2 4>; /* Bit: 2, level */ + }; + }; diff --git a/Documentation/devicetree/bindings/misc/eeprom-93xx46.txt b/Documentation/devicetree/bindings/misc/eeprom-93xx46.txt new file mode 100644 index 0000000..a8ebb46 --- /dev/null +++ b/Documentation/devicetree/bindings/misc/eeprom-93xx46.txt @@ -0,0 +1,25 @@ +EEPROMs (SPI) compatible with Microchip Technology 93xx46 family. + +Required properties: +- compatible : shall be one of: + "atmel,at93c46d" + "eeprom-93xx46" +- data-size : number of data bits per word (either 8 or 16) + +Optional properties: +- read-only : parameter-less property which disables writes to the EEPROM +- select-gpios : if present, specifies the GPIO that will be asserted prior to + each access to the EEPROM (e.g. for SPI bus multiplexing) + +Property rules described in Documentation/devicetree/bindings/spi/spi-bus.txt +apply. In particular, "reg" and "spi-max-frequency" properties must be given. + +Example: + eeprom@0 { + compatible = "eeprom-93xx46"; + reg = <0>; + spi-max-frequency = <1000000>; + spi-cs-high; + data-size = <8>; + select-gpios = <&gpio4 4 GPIO_ACTIVE_HIGH>; + }; diff --git a/Documentation/devicetree/bindings/mmc/arasan,sdhci.txt b/Documentation/devicetree/bindings/mmc/arasan,sdhci.txt index da541c3..31b35c3 100644 --- a/Documentation/devicetree/bindings/mmc/arasan,sdhci.txt +++ b/Documentation/devicetree/bindings/mmc/arasan,sdhci.txt @@ -1,11 +1,12 @@ Device Tree Bindings for the Arasan SDHCI Controller - The bindings follow the mmc[1], clock[2] and interrupt[3] bindings. Only - deviations are documented here. + The bindings follow the mmc[1], clock[2], interrupt[3] and phy[4] bindings. + Only deviations are documented here. [1] Documentation/devicetree/bindings/mmc/mmc.txt [2] Documentation/devicetree/bindings/clock/clock-bindings.txt [3] Documentation/devicetree/bindings/interrupt-controller/interrupts.txt + [4] Documentation/devicetree/bindings/phy/phy-bindings.txt Required Properties: - compatible: Compatibility string. Must be 'arasan,sdhci-8.9a' or @@ -17,6 +18,10 @@ Required Properties: - interrupt-parent: Phandle for the interrupt controller that services interrupts for this device. +Required Properties for "arasan,sdhci-5.1": + - phys: From PHY bindings: Phandle for the Generic PHY for arasan. + - phy-names: MUST be "phy_arasan". + Example: sdhci@e0100000 { compatible = "arasan,sdhci-8.9a"; @@ -26,3 +31,14 @@ Example: interrupt-parent = <&gic>; interrupts = <0 24 4>; } ; + + sdhci@e2800000 { + compatible = "arasan,sdhci-5.1"; + reg = <0xe2800000 0x1000>; + clock-names = "clk_xin", "clk_ahb"; + clocks = <&cru 8>, <&cru 18>; + interrupt-parent = <&gic>; + interrupts = <0 24 4>; + phys = <&emmc_phy>; + phy-names = "phy_arasan"; + } ; diff --git a/Documentation/devicetree/bindings/mmc/brcm,sdhci-iproc.txt b/Documentation/devicetree/bindings/mmc/brcm,sdhci-iproc.txt index 72cc9cc..be56d2b 100644 --- a/Documentation/devicetree/bindings/mmc/brcm,sdhci-iproc.txt +++ b/Documentation/devicetree/bindings/mmc/brcm,sdhci-iproc.txt @@ -4,7 +4,10 @@ This file documents differences between the core properties described by mmc.txt and the properties that represent the IPROC SDHCI controller. Required properties: -- compatible : Should be "brcm,sdhci-iproc-cygnus". +- compatible : Should be one of the following + "brcm,bcm2835-sdhci" + "brcm,sdhci-iproc-cygnus" + - clocks : The clock feeding the SDHCI controller. Optional properties: diff --git a/Documentation/devicetree/bindings/mmc/microchip,sdhci-pic32.txt b/Documentation/devicetree/bindings/mmc/microchip,sdhci-pic32.txt new file mode 100644 index 0000000..71ad57e --- /dev/null +++ b/Documentation/devicetree/bindings/mmc/microchip,sdhci-pic32.txt @@ -0,0 +1,29 @@ +* Microchip PIC32 SDHCI Controller + +This file documents differences between the core properties in mmc.txt +and the properties used by the sdhci-pic32 driver. + +Required properties: +- compatible: Should be "microchip,pic32mzda-sdhci" +- interrupts: Should contain interrupt +- clock-names: Should be "base_clk", "sys_clk". + See: Documentation/devicetree/bindings/resource-names.txt +- clocks: Phandle to the clock. + See: Documentation/devicetree/bindings/clock/clock-bindings.txt +- pinctrl-names: A pinctrl state names "default" must be defined. +- pinctrl-0: Phandle referencing pin configuration of the SDHCI controller. + See: Documentation/devicetree/bindings/pinctrl/pinctrl-binding.txt + +Example: + + sdhci@1f8ec000 { + compatible = "microchip,pic32mzda-sdhci"; + reg = <0x1f8ec000 0x100>; + interrupts = <191 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&REFCLKO4>, <&PBCLK5>; + clock-names = "base_clk", "sys_clk"; + bus-width = <4>; + cap-sd-highspeed; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_sdhc1>; + }; diff --git a/Documentation/devicetree/bindings/mmc/rockchip-dw-mshc.txt b/Documentation/devicetree/bindings/mmc/rockchip-dw-mshc.txt index 3dc13b6..ea5614b 100644 --- a/Documentation/devicetree/bindings/mmc/rockchip-dw-mshc.txt +++ b/Documentation/devicetree/bindings/mmc/rockchip-dw-mshc.txt @@ -13,6 +13,8 @@ Required Properties: - "rockchip,rk2928-dw-mshc": for Rockchip RK2928 and following, before RK3288 - "rockchip,rk3288-dw-mshc": for Rockchip RK3288 + - "rockchip,rk3036-dw-mshc", "rockchip,rk3288-dw-mshc": for Rockchip RK3036 + - "rockchip,rk3368-dw-mshc", "rockchip,rk3288-dw-mshc": for Rockchip RK3368 Optional Properties: * clocks: from common clock binding: if ciu_drive and ciu_sample are diff --git a/Documentation/devicetree/bindings/mmc/tmio_mmc.txt b/Documentation/devicetree/bindings/mmc/tmio_mmc.txt index 400b640..7fb746d 100644 --- a/Documentation/devicetree/bindings/mmc/tmio_mmc.txt +++ b/Documentation/devicetree/bindings/mmc/tmio_mmc.txt @@ -22,6 +22,7 @@ Required properties: "renesas,sdhi-r8a7792" - SDHI IP on R8A7792 SoC "renesas,sdhi-r8a7793" - SDHI IP on R8A7793 SoC "renesas,sdhi-r8a7794" - SDHI IP on R8A7794 SoC + "renesas,sdhi-r8a7795" - SDHI IP on R8A7795 SoC Optional properties: - toshiba,mmc-wrprotect-disable: write-protect detection is unavailable diff --git a/Documentation/devicetree/bindings/mtd/atmel-nand.txt b/Documentation/devicetree/bindings/mtd/atmel-nand.txt index 7d4c8eb..d53aba9 100644 --- a/Documentation/devicetree/bindings/mtd/atmel-nand.txt +++ b/Documentation/devicetree/bindings/mtd/atmel-nand.txt @@ -1,7 +1,10 @@ Atmel NAND flash Required properties: -- compatible : should be "atmel,at91rm9200-nand" or "atmel,sama5d4-nand". +- compatible: The possible values are: + "atmel,at91rm9200-nand" + "atmel,sama5d2-nand" + "atmel,sama5d4-nand" - reg : should specify localbus address and size used for the chip, and hardware ECC controller if available. If the hardware ECC is PMECC, it should contain address and size for @@ -21,10 +24,11 @@ Optional properties: - nand-ecc-mode : String, operation mode of the NAND ecc mode, soft by default. Supported values are: "none", "soft", "hw", "hw_syndrome", "hw_oob_first", "soft_bch". -- atmel,has-pmecc : boolean to enable Programmable Multibit ECC hardware. - Only supported by at91sam9x5 or later sam9 product. +- atmel,has-pmecc : boolean to enable Programmable Multibit ECC hardware, + capable of BCH encoding and decoding, on devices where it is present. - atmel,pmecc-cap : error correct capability for Programmable Multibit ECC - Controller. Supported values are: 2, 4, 8, 12, 24. + Controller. Supported values are: 2, 4, 8, 12, 24. If the compatible string + is "atmel,sama5d2-nand", 32 is also valid. - atmel,pmecc-sector-size : sector size for ECC computation. Supported values are: 512, 1024. - atmel,pmecc-lookup-table-offset : includes two offsets of lookup table in ROM @@ -32,15 +36,16 @@ Optional properties: sector size 1024. If not specified, driver will build the table in runtime. - nand-bus-width : 8 or 16 bus width if not present 8 - nand-on-flash-bbt: boolean to enable on flash bbt option if not present false -- Nand Flash Controller(NFC) is a slave driver under Atmel nand flash - - Required properties: - - compatible : "atmel,sama5d3-nfc". - - reg : should specify the address and size used for NFC command registers, - NFC registers and NFC Sram. NFC Sram address and size can be absent - if don't want to use it. - - clocks: phandle to the peripheral clock - - Optional properties: - - atmel,write-by-sram: boolean to enable NFC write by sram. + +Nand Flash Controller(NFC) is an optional sub-node +Required properties: +- compatible : "atmel,sama5d3-nfc" or "atmel,sama5d4-nfc". +- reg : should specify the address and size used for NFC command registers, + NFC registers and NFC SRAM. NFC SRAM address and size can be absent + if don't want to use it. +- clocks: phandle to the peripheral clock +Optional properties: +- atmel,write-by-sram: boolean to enable NFC write by SRAM. Examples: nand0: nand@40000000,0 { diff --git a/Documentation/devicetree/bindings/mtd/fsl-quadspi.txt b/Documentation/devicetree/bindings/mtd/fsl-quadspi.txt index 00c587b..0333ec8 100644 --- a/Documentation/devicetree/bindings/mtd/fsl-quadspi.txt +++ b/Documentation/devicetree/bindings/mtd/fsl-quadspi.txt @@ -3,7 +3,9 @@ Required properties: - compatible : Should be "fsl,vf610-qspi", "fsl,imx6sx-qspi", "fsl,imx7d-qspi", "fsl,imx6ul-qspi", - "fsl,ls1021-qspi" + "fsl,ls1021a-qspi" + or + "fsl,ls2080a-qspi" followed by "fsl,ls1021a-qspi" - reg : the first contains the register location and length, the second contains the memory mapping address and length - reg-names: Should contain the reg names "QuadSPI" and "QuadSPI-memory" @@ -19,6 +21,7 @@ Optional properties: But if there are two NOR flashes connected to the bus, you should enable this property. (Please check the board's schematic.) + - big-endian : That means the IP register is big endian Example: diff --git a/Documentation/devicetree/bindings/mtd/qcom_nandc.txt b/Documentation/devicetree/bindings/mtd/qcom_nandc.txt new file mode 100644 index 0000000..70dd511 --- /dev/null +++ b/Documentation/devicetree/bindings/mtd/qcom_nandc.txt @@ -0,0 +1,86 @@ +* Qualcomm NAND controller + +Required properties: +- compatible: should be "qcom,ipq806x-nand" +- reg: MMIO address range +- clocks: must contain core clock and always on clock +- clock-names: must contain "core" for the core clock and "aon" for the + always on clock +- dmas: DMA specifier, consisting of a phandle to the ADM DMA + controller node and the channel number to be used for + NAND. Refer to dma.txt and qcom_adm.txt for more details +- dma-names: must be "rxtx" +- qcom,cmd-crci: must contain the ADM command type CRCI block instance + number specified for the NAND controller on the given + platform +- qcom,data-crci: must contain the ADM data type CRCI block instance + number specified for the NAND controller on the given + platform +- #address-cells: <1> - subnodes give the chip-select number +- #size-cells: <0> + +* NAND chip-select + +Each controller may contain one or more subnodes to represent enabled +chip-selects which (may) contain NAND flash chips. Their properties are as +follows. + +Required properties: +- compatible: should contain "qcom,nandcs" +- reg: a single integer representing the chip-select + number (e.g., 0, 1, 2, etc.) +- #address-cells: see partition.txt +- #size-cells: see partition.txt +- nand-ecc-strength: see nand.txt +- nand-ecc-step-size: must be 512. see nand.txt for more details. + +Optional properties: +- nand-bus-width: see nand.txt + +Each nandcs device node may optionally contain a 'partitions' sub-node, which +further contains sub-nodes describing the flash partition mapping. See +partition.txt for more detail. + +Example: + +nand@1ac00000 { + compatible = "qcom,ebi2-nandc"; + reg = <0x1ac00000 0x800>; + + clocks = <&gcc EBI2_CLK>, + <&gcc EBI2_AON_CLK>; + clock-names = "core", "aon"; + + dmas = <&adm_dma 3>; + dma-names = "rxtx"; + qcom,cmd-crci = <15>; + qcom,data-crci = <3>; + + #address-cells = <1>; + #size-cells = <0>; + + nandcs@0 { + compatible = "qcom,nandcs"; + reg = <0>; + + nand-ecc-strength = <4>; + nand-ecc-step-size = <512>; + nand-bus-width = <8>; + + partitions { + compatible = "fixed-partitions"; + #address-cells = <1>; + #size-cells = <1>; + + partition@0 { + label = "boot-nand"; + reg = <0 0x58a0000>; + }; + + partition@58a0000 { + label = "fs-nand"; + reg = <0x58a0000 0x4000000>; + }; + }; + }; +}; diff --git a/Documentation/devicetree/bindings/net/arc_emac.txt b/Documentation/devicetree/bindings/net/arc_emac.txt index a1d71eb..c73a0e9 100644 --- a/Documentation/devicetree/bindings/net/arc_emac.txt +++ b/Documentation/devicetree/bindings/net/arc_emac.txt @@ -7,6 +7,13 @@ Required properties: - max-speed: see ethernet.txt file in the same directory. - phy: see ethernet.txt file in the same directory. +Optional properties: +- phy-reset-gpios : Should specify the gpio for phy reset +- phy-reset-duration : Reset duration in milliseconds. Should present + only if property "phy-reset-gpios" is available. Missing the property + will have the duration be 1 millisecond. Numbers greater than 1000 are + invalid and 1 millisecond will be used instead. + Clock handling: The clock frequency is needed to calculate and set polling period of EMAC. It must be provided by one of: diff --git a/Documentation/devicetree/bindings/net/can/ifi_canfd.txt b/Documentation/devicetree/bindings/net/can/ifi_canfd.txt new file mode 100644 index 0000000..20ea5c7 --- /dev/null +++ b/Documentation/devicetree/bindings/net/can/ifi_canfd.txt @@ -0,0 +1,15 @@ +IFI CANFD controller +-------------------- + +Required properties: + - compatible: Should be "ifi,canfd-1.0" + - reg: Should contain CAN controller registers location and length + - interrupts: Should contain IRQ line for the CAN controller + +Example: + + canfd0: canfd@ff220000 { + compatible = "ifi,canfd-1.0"; + reg = <0xff220000 0x00001000>; + interrupts = <0 43 0>; + }; diff --git a/Documentation/devicetree/bindings/net/can/rcar_can.txt b/Documentation/devicetree/bindings/net/can/rcar_can.txt index 002d844..8d40ab2 100644 --- a/Documentation/devicetree/bindings/net/can/rcar_can.txt +++ b/Documentation/devicetree/bindings/net/can/rcar_can.txt @@ -6,6 +6,17 @@ Required properties: "renesas,can-r8a7779" if CAN controller is a part of R8A7779 SoC. "renesas,can-r8a7790" if CAN controller is a part of R8A7790 SoC. "renesas,can-r8a7791" if CAN controller is a part of R8A7791 SoC. + "renesas,can-r8a7792" if CAN controller is a part of R8A7792 SoC. + "renesas,can-r8a7793" if CAN controller is a part of R8A7793 SoC. + "renesas,can-r8a7794" if CAN controller is a part of R8A7794 SoC. + "renesas,can-r8a7795" if CAN controller is a part of R8A7795 SoC. + "renesas,rcar-gen1-can" for a generic R-Car Gen1 compatible device. + "renesas,rcar-gen2-can" for a generic R-Car Gen2 compatible device. + "renesas,rcar-gen3-can" for a generic R-Car Gen3 compatible device. + When compatible with the generic version, nodes must list the + SoC-specific version corresponding to the platform first + followed by the generic version. + - reg: physical base address and size of the R-Car CAN register map. - interrupts: interrupt specifier for the sole interrupt. - clocks: phandles and clock specifiers for 3 CAN clock inputs. @@ -13,6 +24,15 @@ Required properties: - pinctrl-0: pin control group to be used for this controller. - pinctrl-names: must be "default". +Required properties for "renesas,can-r8a7795" compatible: +In R8A7795 SoC, "clkp2" can be CANFD clock. This is a div6 clock and can be +used by both CAN and CAN FD controller at the same time. It needs to be scaled +to maximum frequency if any of these controllers use it. This is done using +the below properties. + +- assigned-clocks: phandle of clkp2(CANFD) clock. +- assigned-clock-rates: maximum frequency of this clock. + Optional properties: - renesas,can-clock-select: R-Car CAN Clock Source Select. Valid values are: <0x0> (default) : Peripheral clock (clkp1) @@ -25,7 +45,7 @@ Example SoC common .dtsi file: can0: can@e6e80000 { - compatible = "renesas,can-r8a7791"; + compatible = "renesas,can-r8a7791", "renesas,rcar-gen2-can"; reg = <0 0xe6e80000 0 0x1000>; interrupts = <0 186 IRQ_TYPE_LEVEL_HIGH>; clocks = <&mstp9_clks R8A7791_CLK_RCAN0>, diff --git a/Documentation/devicetree/bindings/net/can/sja1000.txt b/Documentation/devicetree/bindings/net/can/sja1000.txt index b4a6d53..ac3160e 100644 --- a/Documentation/devicetree/bindings/net/can/sja1000.txt +++ b/Documentation/devicetree/bindings/net/can/sja1000.txt @@ -2,7 +2,7 @@ Memory mapped SJA1000 CAN controller from NXP (formerly Philips) Required properties: -- compatible : should be "nxp,sja1000". +- compatible : should be one of "nxp,sja1000", "technologic,sja1000". - reg : should specify the chip select, address offset and size required to map the registers of the SJA1000. The size is usually 0x80. @@ -14,6 +14,7 @@ Optional properties: - reg-io-width : Specify the size (in bytes) of the IO accesses that should be performed on the device. Valid value is 1, 2 or 4. + This property is ignored for technologic version. Default to 1 (8 bits). - nxp,external-clock-frequency : Frequency of the external oscillator diff --git a/Documentation/devicetree/bindings/net/cavium-mdio.txt b/Documentation/devicetree/bindings/net/cavium-mdio.txt index 04cb749..020df08 100644 --- a/Documentation/devicetree/bindings/net/cavium-mdio.txt +++ b/Documentation/devicetree/bindings/net/cavium-mdio.txt @@ -1,9 +1,12 @@ * System Management Interface (SMI) / MDIO Properties: -- compatible: "cavium,octeon-3860-mdio" +- compatible: One of: - Compatibility with all cn3XXX, cn5XXX and cn6XXX SOCs. + "cavium,octeon-3860-mdio": Compatibility with all cn3XXX, cn5XXX + and cn6XXX SOCs. + + "cavium,thunder-8890-mdio": Compatibility with all cn8XXX SOCs. - reg: The base address of the MDIO bus controller register bank. @@ -25,3 +28,57 @@ Example: reg = <0>; }; }; + + +* System Management Interface (SMI) / MDIO Nexus + + Several mdio buses may be gathered as children of a single PCI + device, this PCI device is the nexus of the buses. + +Properties: + +- compatible: "cavium,thunder-8890-mdio-nexus"; + +- reg: The PCI device and function numbers of the nexus device. + +- #address-cells: Must be <2>. + +- #size-cells: Must be <2>. + +- ranges: As needed for mapping of the MDIO bus device registers. + +- assigned-addresses: As needed for mapping of the MDIO bus device registers. + +Example: + + mdio-nexus@1,3 { + compatible = "cavium,thunder-8890-mdio-nexus"; + #address-cells = <2>; + #size-cells = <2>; + reg = <0x0b00 0 0 0 0>; /* DEVFN = 0x0b (1:3) */ + assigned-addresses = <0x03000000 0x87e0 0x05000000 0x0 0x800000>; + ranges = <0x87e0 0x05000000 0x03000000 0x87e0 0x05000000 0x0 0x800000>; + + mdio0@87e0,05003800 { + compatible = "cavium,thunder-8890-mdio"; + #address-cells = <1>; + #size-cells = <0>; + reg = <0x87e0 0x05003800 0x0 0x30>; + + ethernet-phy@0 { + ... + reg = <0>; + }; + }; + mdio0@87e0,05003880 { + compatible = "cavium,thunder-8890-mdio"; + #address-cells = <1>; + #size-cells = <0>; + reg = <0x87e0 0x05003880 0x0 0x30>; + + ethernet-phy@0 { + ... + reg = <0>; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/net/cpsw.txt b/Documentation/devicetree/bindings/net/cpsw.txt index 28a4781..0ae0649 100644 --- a/Documentation/devicetree/bindings/net/cpsw.txt +++ b/Documentation/devicetree/bindings/net/cpsw.txt @@ -45,13 +45,13 @@ Required properties: Optional properties: - dual_emac_res_vlan : Specifies VID to be used to segregate the ports - mac-address : See ethernet.txt file in the same directory -- phy_id : Specifies slave phy id +- phy_id : Specifies slave phy id (deprecated, use phy-handle) - phy-handle : See ethernet.txt file in the same directory Slave sub-nodes: - fixed-link : See fixed-link.txt file in the same directory - Either the property phy_id, or the sub-node - fixed-link can be specified + +Note: Exactly one of phy_id, phy-handle, or fixed-link must be specified. Note: "ti,hwmods" field is used to fetch the base address and irq resources from TI, omap hwmod data base during device registration. diff --git a/Documentation/devicetree/bindings/net/emac_rockchip.txt b/Documentation/devicetree/bindings/net/emac_rockchip.txt index 8dc1c79..05bd7da 100644 --- a/Documentation/devicetree/bindings/net/emac_rockchip.txt +++ b/Documentation/devicetree/bindings/net/emac_rockchip.txt @@ -1,8 +1,10 @@ -* ARC EMAC 10/100 Ethernet platform driver for Rockchip Rk3066/RK3188 SoCs +* ARC EMAC 10/100 Ethernet platform driver for Rockchip RK3036/RK3066/RK3188 SoCs Required properties: -- compatible: Should be "rockchip,rk3066-emac" or "rockchip,rk3188-emac" - according to the target SoC. +- compatible: should be "rockchip,<name>-emac" + "rockchip,rk3036-emac": found on RK3036 SoCs + "rockchip,rk3066-emac": found on RK3066 SoCs + "rockchip,rk3188-emac": found on RK3188 SoCs - reg: Address and length of the register set for the device - interrupts: Should contain the EMAC interrupts - rockchip,grf: phandle to the syscon grf used to control speed and mode diff --git a/Documentation/devicetree/bindings/net/fsl-fec.txt b/Documentation/devicetree/bindings/net/fsl-fec.txt index a9eb611..b037a9d 100644 --- a/Documentation/devicetree/bindings/net/fsl-fec.txt +++ b/Documentation/devicetree/bindings/net/fsl-fec.txt @@ -12,6 +12,9 @@ Optional properties: only if property "phy-reset-gpios" is available. Missing the property will have the duration be 1 millisecond. Numbers greater than 1000 are invalid and 1 millisecond will be used instead. +- phy-reset-active-high : If present then the reset sequence using the GPIO + specified in the "phy-reset-gpios" property is reversed (H=reset state, + L=operation state). - phy-supply : regulator that powers the Ethernet PHY. - phy-handle : phandle to the PHY device connected to this device. - fixed-link : Assume a fixed link. See fixed-link.txt in the same directory. diff --git a/Documentation/devicetree/bindings/net/macb.txt b/Documentation/devicetree/bindings/net/macb.txt index d2e243b..b5a42df 100644 --- a/Documentation/devicetree/bindings/net/macb.txt +++ b/Documentation/devicetree/bindings/net/macb.txt @@ -25,6 +25,8 @@ Required properties: Optional properties for PHY child node: - reset-gpios : Should specify the gpio for phy reset +- magic-packet : If present, indicates that the hardware supports waking + up via magic packet. Examples: diff --git a/Documentation/devicetree/bindings/net/marvell-armada-370-neta.txt b/Documentation/devicetree/bindings/net/marvell-armada-370-neta.txt index d0cb869..73be897 100644 --- a/Documentation/devicetree/bindings/net/marvell-armada-370-neta.txt +++ b/Documentation/devicetree/bindings/net/marvell-armada-370-neta.txt @@ -18,15 +18,30 @@ Optional properties: "core" for core clock and "bus" for the optional bus clock. +Optional properties (valid only for Armada XP/38x): + +- buffer-manager: a phandle to a buffer manager node. Please refer to + Documentation/devicetree/bindings/net/marvell-neta-bm.txt +- bm,pool-long: ID of a pool, that will accept all packets of a size + higher than 'short' pool's threshold (if set) and up to MTU value. + Obligatory, when the port is supposed to use hardware + buffer management. +- bm,pool-short: ID of a pool, that will be used for accepting + packets of a size lower than given threshold. If not set, the port + will use a single 'long' pool for all packets, as defined above. + Example: -ethernet@d0070000 { +ethernet@70000 { compatible = "marvell,armada-370-neta"; - reg = <0xd0070000 0x2500>; + reg = <0x70000 0x2500>; interrupts = <8>; clocks = <&gate_clk 4>; tx-csum-limit = <9800> status = "okay"; phy = <&phy0>; phy-mode = "rgmii-id"; + buffer-manager = <&bm>; + bm,pool-long = <0>; + bm,pool-short = <1>; }; diff --git a/Documentation/devicetree/bindings/net/marvell-neta-bm.txt b/Documentation/devicetree/bindings/net/marvell-neta-bm.txt new file mode 100644 index 0000000..c1b1d7c3 --- /dev/null +++ b/Documentation/devicetree/bindings/net/marvell-neta-bm.txt @@ -0,0 +1,49 @@ +* Marvell Armada 380/XP Buffer Manager driver (BM) + +Required properties: + +- compatible: should be "marvell,armada-380-neta-bm". +- reg: address and length of the register set for the device. +- clocks: a pointer to the reference clock for this device. +- internal-mem: a phandle to BM internal SRAM definition. + +Optional properties (port): + +- pool<0 : 3>,capacity: size of external buffer pointers' ring maintained + in DRAM. Can be set for each pool (id 0 : 3) separately. The value has + to be chosen between 128 and 16352 and it also has to be aligned to 32. + Otherwise the driver would adjust a given number or choose default if + not set. +- pool<0 : 3>,pkt-size: maximum size of a packet accepted by a given buffer + pointers' pool (id 0 : 3). It will be taken into consideration only when pool + type is 'short'. For 'long' ones it would be overridden by port's MTU. + If not set a driver will choose a default value. + +In order to see how to hook the BM to a given ethernet port, please +refer to Documentation/devicetree/bindings/net/marvell-armada-370-neta.txt. + +Example: + +- main node: + +bm: bm@c8000 { + compatible = "marvell,armada-380-neta-bm"; + reg = <0xc8000 0xac>; + clocks = <&gateclk 13>; + internal-mem = <&bm_bppi>; + status = "okay"; + pool2,capacity = <4096>; + pool1,pkt-size = <512>; +}; + +- internal SRAM node: + +bm_bppi: bm-bppi { + compatible = "mmio-sram"; + reg = <MBUS_ID(0x0c, 0x04) 0 0x100000>; + ranges = <0 MBUS_ID(0x0c, 0x04) 0 0x100000>; + #address-cells = <1>; + #size-cells = <1>; + clocks = <&gateclk 13>; + status = "okay"; +}; diff --git a/Documentation/devicetree/bindings/net/mediatek-net.txt b/Documentation/devicetree/bindings/net/mediatek-net.txt new file mode 100644 index 0000000..32eaaca --- /dev/null +++ b/Documentation/devicetree/bindings/net/mediatek-net.txt @@ -0,0 +1,80 @@ +MediaTek Frame Engine Ethernet controller +========================================= + +The frame engine ethernet controller can be found on MediaTek SoCs. These SoCs +have dual GMAC each represented by a child node.. + +* Ethernet controller node + +Required properties: +- compatible: Should be "mediatek,mt7623-eth" +- reg: Address and length of the register set for the device +- interrupts: Should contain the three frame engines interrupts in numeric + order. These are fe_int0, fe_int1 and fe_int2. +- clocks: the clock used by the core +- clock-names: the names of the clock listed in the clocks property. These are + "ethif", "esw", "gp2", "gp1" +- power-domains: phandle to the power domain that the ethernet is part of +- resets: Should contain a phandle to the ethsys reset signal +- reset-names: Should contain the reset signal name "eth" +- mediatek,ethsys: phandle to the syscon node that handles the port setup +- mediatek,pctl: phandle to the syscon node that handles the ports slew rate + and driver current + +Optional properties: +- interrupt-parent: Should be the phandle for the interrupt controller + that services interrupts for this device + + +* Ethernet MAC node + +Required properties: +- compatible: Should be "mediatek,eth-mac" +- reg: The number of the MAC +- phy-handle: see ethernet.txt file in the same directory. + +Example: + +eth: ethernet@1b100000 { + compatible = "mediatek,mt7623-eth"; + reg = <0 0x1b100000 0 0x20000>; + clocks = <&topckgen CLK_TOP_ETHIF_SEL>, + <ðsys CLK_ETHSYS_ESW>, + <ðsys CLK_ETHSYS_GP2>, + <ðsys CLK_ETHSYS_GP1>; + clock-names = "ethif", "esw", "gp2", "gp1"; + interrupts = <GIC_SPI 200 IRQ_TYPE_LEVEL_LOW + GIC_SPI 199 IRQ_TYPE_LEVEL_LOW + GIC_SPI 198 IRQ_TYPE_LEVEL_LOW>; + power-domains = <&scpsys MT2701_POWER_DOMAIN_ETH>; + resets = <ðsys MT2701_ETHSYS_ETH_RST>; + reset-names = "eth"; + mediatek,ethsys = <ðsys>; + mediatek,pctl = <&syscfg_pctl_a>; + #address-cells = <1>; + #size-cells = <0>; + + gmac1: mac@0 { + compatible = "mediatek,eth-mac"; + reg = <0>; + phy-handle = <&phy0>; + }; + + gmac2: mac@1 { + compatible = "mediatek,eth-mac"; + reg = <1>; + phy-handle = <&phy1>; + }; + + mdio-bus { + phy0: ethernet-phy@0 { + reg = <0>; + phy-mode = "rgmii"; + }; + + phy1: ethernet-phy@1 { + reg = <1>; + phy-mode = "rgmii"; + }; + }; +}; diff --git a/Documentation/devicetree/bindings/net/micrel-ks8995.txt b/Documentation/devicetree/bindings/net/micrel-ks8995.txt new file mode 100644 index 0000000..281bc24 --- /dev/null +++ b/Documentation/devicetree/bindings/net/micrel-ks8995.txt @@ -0,0 +1,20 @@ +Micrel KS8995 SPI controlled Ethernet Switch families + +Required properties (according to spi-bus.txt): +- compatible: either "micrel,ks8995", "micrel,ksz8864" or "micrel,ksz8795" + +Optional properties: +- reset-gpios : phandle of gpio that will be used to reset chip during probe + +Example: + +spi-master { + ... + switch@0 { + compatible = "micrel,ksz8795"; + + reg = <0>; + spi-max-frequency = <50000000>; + reset-gpios = <&gpio0 46 GPIO_ACTIVE_LOW>; + }; +}; diff --git a/Documentation/devicetree/bindings/net/stmmac.txt b/Documentation/devicetree/bindings/net/stmmac.txt index e862a92..6605d19 100644 --- a/Documentation/devicetree/bindings/net/stmmac.txt +++ b/Documentation/devicetree/bindings/net/stmmac.txt @@ -17,7 +17,25 @@ Required properties: The 1st cell is reset pre-delay in micro seconds. The 2nd cell is reset pulse in micro seconds. The 3rd cell is reset post-delay in micro seconds. + +Optional properties: +- resets: Should contain a phandle to the STMMAC reset signal, if any +- reset-names: Should contain the reset signal name "stmmaceth", if a + reset phandle is given +- max-frame-size: See ethernet.txt file in the same directory +- clocks: If present, the first clock should be the GMAC main clock and + the second clock should be peripheral's register interface clock. Further + clocks may be specified in derived bindings. +- clock-names: One name for each entry in the clocks property, the + first one should be "stmmaceth" and the second one should be "pclk". +- clk_ptp_ref: this is the PTP reference clock; in case of the PTP is + available this clock is used for programming the Timestamp Addend Register. + If not passed then the system clock will be used and this is fine on some + platforms. +- tx-fifo-depth: See ethernet.txt file in the same directory +- rx-fifo-depth: See ethernet.txt file in the same directory - snps,pbl Programmable Burst Length +- snps,aal Address-Aligned Beats - snps,fixed-burst Program the DMA to use the fixed burst mode - snps,mixed-burst Program the DMA to use the mixed burst mode - snps,force_thresh_dma_mode Force DMA to use the threshold mode for @@ -29,27 +47,28 @@ Required properties: supported by this device instance - snps,perfect-filter-entries: Number of perfect filter entries supported by this device instance - -Optional properties: -- resets: Should contain a phandle to the STMMAC reset signal, if any -- reset-names: Should contain the reset signal name "stmmaceth", if a - reset phandle is given -- max-frame-size: See ethernet.txt file in the same directory -- clocks: If present, the first clock should be the GMAC main clock - The optional second clock should be peripheral's register interface clock. - The third optional clock should be the ptp reference clock. - Further clocks may be specified in derived bindings. -- clock-names: One name for each entry in the clocks property. - The first one should be "stmmaceth". - The optional second one should be "pclk". - The optional third one should be "clk_ptp_ref". -- snps,burst_len: The AXI burst lenth value of the AXI BUS MODE register. -- tx-fifo-depth: See ethernet.txt file in the same directory -- rx-fifo-depth: See ethernet.txt file in the same directory +- AXI BUS Mode parameters: below the list of all the parameters to program the + AXI register inside the DMA module: + - snps,lpi_en: enable Low Power Interface + - snps,xit_frm: unlock on WoL + - snps,wr_osr_lmt: max write oustanding req. limit + - snps,rd_osr_lmt: max read oustanding req. limit + - snps,kbbe: do not cross 1KiB boundary. + - snps,axi_all: align address + - snps,blen: this is a vector of supported burst length. + - snps,fb: fixed-burst + - snps,mb: mixed-burst + - snps,rb: rebuild INCRx Burst - mdio: with compatible = "snps,dwmac-mdio", create and register mdio bus. Examples: + stmmac_axi_setup: stmmac-axi-config { + snps,wr_osr_lmt = <0xf>; + snps,rd_osr_lmt = <0xf>; + snps,blen = <256 128 64 32 0 0 0>; + }; + gmac0: ethernet@e0800000 { compatible = "st,spear600-gmac"; reg = <0xe0800000 0x8000>; @@ -65,6 +84,7 @@ Examples: tx-fifo-depth = <16384>; clocks = <&clock>; clock-names = "stmmaceth"; + snps,axi-config = <&stmmac_axi_setup>; mdio0 { #address-cells = <1>; #size-cells = <0>; diff --git a/Documentation/devicetree/bindings/net/wireless/qcom,ath10k.txt b/Documentation/devicetree/bindings/net/wireless/qcom,ath10k.txt index edefc26..96aae6b 100644 --- a/Documentation/devicetree/bindings/net/wireless/qcom,ath10k.txt +++ b/Documentation/devicetree/bindings/net/wireless/qcom,ath10k.txt @@ -1,17 +1,46 @@ * Qualcomm Atheros ath10k wireless devices -For ath10k devices the calibration data can be provided through Device -Tree. The node is a child node of the PCI controller. - Required properties: --compatible : Should be "qcom,ath10k" +- compatible: Should be one of the following: + * "qcom,ath10k" + * "qcom,ipq4019-wifi" + +PCI based devices uses compatible string "qcom,ath10k" and takes only +calibration data via "qcom,ath10k-calibration-data". Rest of the properties +are not applicable for PCI based devices. + +AHB based devices (i.e. ipq4019) uses compatible string "qcom,ipq4019-wifi" +and also uses most of the properties defined in this doc. Optional properties: +- reg: Address and length of the register set for the device. +- resets: Must contain an entry for each entry in reset-names. + See ../reset/reseti.txt for details. +- reset-names: Must include the list of following reset names, + "wifi_cpu_init" + "wifi_radio_srif" + "wifi_radio_warm" + "wifi_radio_cold" + "wifi_core_warm" + "wifi_core_cold" +- clocks: List of clock specifiers, must contain an entry for each required + entry in clock-names. +- clock-names: Should contain the clock names "wifi_wcss_cmd", "wifi_wcss_ref", + "wifi_wcss_rtc". +- interrupts: List of interrupt lines. Must contain an entry + for each entry in the interrupt-names property. +- interrupt-names: Must include the entries for MSI interrupt + names ("msi0" to "msi15") and legacy interrupt + name ("legacy"), +- qcom,msi_addr: MSI interrupt address. +- qcom,msi_base: Base value to add before writing MSI data into + MSI address register. - qcom,ath10k-calibration-data : calibration data as an array, the length can vary between hw versions +Example (to supply the calibration data alone): -Example: +In this example, the node is defined as child node of the PCI controller. pci { pcie@0 { @@ -28,3 +57,53 @@ pci { }; }; }; + +Example (to supply ipq4019 SoC wifi block details): + +wifi0: wifi@a000000 { + compatible = "qcom,ipq4019-wifi"; + reg = <0xa000000 0x200000>; + resets = <&gcc WIFI0_CPU_INIT_RESET>, + <&gcc WIFI0_RADIO_SRIF_RESET>, + <&gcc WIFI0_RADIO_WARM_RESET>, + <&gcc WIFI0_RADIO_COLD_RESET>, + <&gcc WIFI0_CORE_WARM_RESET>, + <&gcc WIFI0_CORE_COLD_RESET>; + reset-names = "wifi_cpu_init", + "wifi_radio_srif", + "wifi_radio_warm", + "wifi_radio_cold", + "wifi_core_warm", + "wifi_core_cold"; + clocks = <&gcc GCC_WCSS2G_CLK>, + <&gcc GCC_WCSS2G_REF_CLK>, + <&gcc GCC_WCSS2G_RTC_CLK>; + clock-names = "wifi_wcss_cmd", + "wifi_wcss_ref", + "wifi_wcss_rtc"; + interrupts = <0 0x20 0x1>, + <0 0x21 0x1>, + <0 0x22 0x1>, + <0 0x23 0x1>, + <0 0x24 0x1>, + <0 0x25 0x1>, + <0 0x26 0x1>, + <0 0x27 0x1>, + <0 0x28 0x1>, + <0 0x29 0x1>, + <0 0x2a 0x1>, + <0 0x2b 0x1>, + <0 0x2c 0x1>, + <0 0x2d 0x1>, + <0 0x2e 0x1>, + <0 0x2f 0x1>, + <0 0xa8 0x0>; + interrupt-names = "msi0", "msi1", "msi2", "msi3", + "msi4", "msi5", "msi6", "msi7", + "msi8", "msi9", "msi10", "msi11", + "msi12", "msi13", "msi14", "msi15", + "legacy"; + qcom,msi_addr = <0x0b006040>; + qcom,msi_base = <0x40>; + qcom,ath10k-calibration-data = [ 01 02 03 ... ]; +}; diff --git a/Documentation/devicetree/bindings/net/wireless/ti,wlcore,spi.txt b/Documentation/devicetree/bindings/net/wireless/ti,wlcore,spi.txt new file mode 100644 index 0000000..9180724 --- /dev/null +++ b/Documentation/devicetree/bindings/net/wireless/ti,wlcore,spi.txt @@ -0,0 +1,36 @@ +* Texas Instruments wl1271 wireless lan controller + +The wl1271 chip can be connected via SPI or via SDIO. This +document describes the binding for the SPI connected chip. + +Required properties: +- compatible : Should be "ti,wl1271" +- reg : Chip select address of device +- spi-max-frequency : Maximum SPI clocking speed of device in Hz +- ref-clock-frequency : Reference clock frequency +- interrupt-parent, interrupts : + Should contain parameters for 1 interrupt line. + Interrupt parameters: parent, line number, type. +- vwlan-supply : Point the node of the regulator that powers/enable the wl1271 chip + +Optional properties: +- clock-xtal : boolean, clock is generated from XTAL + +- Please consult Documentation/devicetree/bindings/spi/spi-bus.txt + for optional SPI connection related properties, + +Examples: + +&spi1 { + wl1271@1 { + compatible = "ti,wl1271"; + + reg = <1>; + spi-max-frequency = <48000000>; + clock-xtal; + ref-clock-frequency = <38400000>; + interrupt-parent = <&gpio3>; + interrupts = <8 IRQ_TYPE_LEVEL_HIGH>; + vwlan-supply = <&vwlan_fixed>; + }; +}; diff --git a/Documentation/devicetree/bindings/nvmem/lpc1857-eeprom.txt b/Documentation/devicetree/bindings/nvmem/lpc1857-eeprom.txt new file mode 100644 index 0000000..809df68 --- /dev/null +++ b/Documentation/devicetree/bindings/nvmem/lpc1857-eeprom.txt @@ -0,0 +1,28 @@ +* NXP LPC18xx EEPROM memory NVMEM driver + +Required properties: + - compatible: Should be "nxp,lpc1857-eeprom" + - reg: Must contain an entry with the physical base address and length + for each entry in reg-names. + - reg-names: Must include the following entries. + - reg: EEPROM registers. + - mem: EEPROM address space. + - clocks: Must contain an entry for each entry in clock-names. + - clock-names: Must include the following entries. + - eeprom: EEPROM operating clock. + - resets: Should contain a reference to the reset controller asserting + the EEPROM in reset. + - interrupts: Should contain EEPROM interrupt. + +Example: + + eeprom: eeprom@4000e000 { + compatible = "nxp,lpc1857-eeprom"; + reg = <0x4000e000 0x1000>, + <0x20040000 0x4000>; + reg-names = "reg", "mem"; + clocks = <&ccu1 CLK_CPU_EEPROM>; + clock-names = "eeprom"; + resets = <&rgu 27>; + interrupts = <4>; + }; diff --git a/Documentation/devicetree/bindings/nvmem/mtk-efuse.txt b/Documentation/devicetree/bindings/nvmem/mtk-efuse.txt new file mode 100644 index 0000000..74cf529 --- /dev/null +++ b/Documentation/devicetree/bindings/nvmem/mtk-efuse.txt @@ -0,0 +1,36 @@ += Mediatek MTK-EFUSE device tree bindings = + +This binding is intended to represent MTK-EFUSE which is found in most Mediatek SOCs. + +Required properties: +- compatible: should be "mediatek,mt8173-efuse" or "mediatek,efuse" +- reg: Should contain registers location and length + += Data cells = +Are child nodes of MTK-EFUSE, bindings of which as described in +bindings/nvmem/nvmem.txt + +Example: + + efuse: efuse@10206000 { + compatible = "mediatek,mt8173-efuse"; + reg = <0 0x10206000 0 0x1000>; + #address-cells = <1>; + #size-cells = <1>; + + /* Data cells */ + thermal_calibration: calib@528 { + reg = <0x528 0xc>; + }; + }; + += Data consumers = +Are device nodes which consume nvmem data cells. + +For example: + + thermal { + ... + nvmem-cells = <&thermal_calibration>; + nvmem-cell-names = "calibration"; + }; diff --git a/Documentation/devicetree/bindings/pci/designware-pcie.txt b/Documentation/devicetree/bindings/pci/designware-pcie.txt index 5b0853d..64f2fff 100644 --- a/Documentation/devicetree/bindings/pci/designware-pcie.txt +++ b/Documentation/devicetree/bindings/pci/designware-pcie.txt @@ -28,3 +28,20 @@ Optional properties: - clock-names: Must include the following entries: - "pcie" - "pcie_bus" + +Example configuration: + + pcie: pcie@0xdffff000 { + compatible = "snps,dw-pcie"; + reg = <0xdffff000 0x1000>, /* Controller registers */ + <0xd0000000 0x2000>; /* PCI config space */ + reg-names = "ctrlreg", "config"; + #address-cells = <3>; + #size-cells = <2>; + device_type = "pci"; + ranges = <0x81000000 0 0x00000000 0xde000000 0 0x00010000 + 0x82000000 0 0xd0400000 0xd0400000 0 0x0d000000>; + interrupts = <25>, <24>; + #interrupt-cells = <1>; + num-lanes = <1>; + }; diff --git a/Documentation/devicetree/bindings/pci/fsl,imx6q-pcie.txt b/Documentation/devicetree/bindings/pci/fsl,imx6q-pcie.txt index 6fbba53..3be80c6 100644 --- a/Documentation/devicetree/bindings/pci/fsl,imx6q-pcie.txt +++ b/Documentation/devicetree/bindings/pci/fsl,imx6q-pcie.txt @@ -13,6 +13,13 @@ Required properties: - clock-names: Must include the following additional entries: - "pcie_phy" +Optional properties: +- fsl,tx-deemph-gen1: Gen1 De-emphasis value. Default: 0 +- fsl,tx-deemph-gen2-3p5db: Gen2 (3.5db) De-emphasis value. Default: 0 +- fsl,tx-deemph-gen2-6db: Gen2 (6db) De-emphasis value. Default: 20 +- fsl,tx-swing-full: Gen2 TX SWING FULL value. Default: 127 +- fsl,tx-swing-low: TX launch amplitude swing_low value. Default: 127 + Example: pcie@0x01000000 { diff --git a/Documentation/devicetree/bindings/pci/layerscape-pci.txt b/Documentation/devicetree/bindings/pci/layerscape-pci.txt index e376785..ef683b2 100644 --- a/Documentation/devicetree/bindings/pci/layerscape-pci.txt +++ b/Documentation/devicetree/bindings/pci/layerscape-pci.txt @@ -14,7 +14,7 @@ information. Required properties: - compatible: should contain the platform identifier such as: "fsl,ls1021a-pcie", "snps,dw-pcie" - "fsl,ls2080a-pcie", "snps,dw-pcie" + "fsl,ls2080a-pcie", "fsl,ls2085a-pcie", "snps,dw-pcie" - reg: base addresses and lengths of the PCIe controller - interrupts: A list of interrupt outputs of the controller. Must contain an entry for each entry in the interrupt-names property. diff --git a/Documentation/devicetree/bindings/pci/pci-thunder-ecam.txt b/Documentation/devicetree/bindings/pci/pci-thunder-ecam.txt new file mode 100644 index 0000000..f478874 --- /dev/null +++ b/Documentation/devicetree/bindings/pci/pci-thunder-ecam.txt @@ -0,0 +1,30 @@ +* ThunderX PCI host controller for pass-1.x silicon + +Firmware-initialized PCI host controller to on-chip devices found on +some Cavium ThunderX processors. These devices have ECAM-based config +access, but the BARs are all at fixed addresses. We handle the fixed +addresses by synthesizing Enhanced Allocation (EA) capabilities for +these devices. + +The properties and their meanings are identical to those described in +host-generic-pci.txt except as listed below. + +Properties of the host controller node that differ from +host-generic-pci.txt: + +- compatible : Must be "cavium,pci-host-thunder-ecam" + +Example: + + pcie@84b000000000 { + compatible = "cavium,pci-host-thunder-ecam"; + device_type = "pci"; + msi-parent = <&its>; + msi-map = <0 &its 0x30000 0x10000>; + bus-range = <0 31>; + #size-cells = <2>; + #address-cells = <3>; + #stream-id-cells = <1>; + reg = <0x84b0 0x00000000 0 0x02000000>; /* Configuration space */ + ranges = <0x03000000 0x8180 0x00000000 0x8180 0x00000000 0x80 0x00000000>; /* mem ranges */ + }; diff --git a/Documentation/devicetree/bindings/pci/pci-thunder-pem.txt b/Documentation/devicetree/bindings/pci/pci-thunder-pem.txt new file mode 100644 index 0000000..f131fae --- /dev/null +++ b/Documentation/devicetree/bindings/pci/pci-thunder-pem.txt @@ -0,0 +1,43 @@ +* ThunderX PEM PCIe host controller + +Firmware-initialized PCI host controller found on some Cavium +ThunderX processors. + +The properties and their meanings are identical to those described in +host-generic-pci.txt except as listed below. + +Properties of the host controller node that differ from +host-generic-pci.txt: + +- compatible : Must be "cavium,pci-host-thunder-pem" + +- reg : Two entries: First the configuration space for down + stream devices base address and size, as accessed + from the parent bus. Second, the register bank of + the PEM device PCIe bridge. + +Example: + + pci@87e0,c2000000 { + compatible = "cavium,pci-host-thunder-pem"; + device_type = "pci"; + msi-parent = <&its>; + msi-map = <0 &its 0x10000 0x10000>; + bus-range = <0x8f 0xc7>; + #size-cells = <2>; + #address-cells = <3>; + + reg = <0x8880 0x8f000000 0x0 0x39000000>, /* Configuration space */ + <0x87e0 0xc2000000 0x0 0x00010000>; /* PEM space */ + ranges = <0x01000000 0x00 0x00020000 0x88b0 0x00020000 0x00 0x00010000>, /* I/O */ + <0x03000000 0x00 0x10000000 0x8890 0x10000000 0x0f 0xf0000000>, /* mem64 */ + <0x43000000 0x10 0x00000000 0x88a0 0x00000000 0x10 0x00000000>, /* mem64-pref */ + <0x03000000 0x87e0 0xc2f00000 0x87e0 0xc2000000 0x00 0x00100000>; /* mem64 PEM BAR4 */ + + #interrupt-cells = <1>; + interrupt-map-mask = <0 0 0 7>; + interrupt-map = <0 0 0 1 &gic0 0 0 0 24 4>, /* INTA */ + <0 0 0 2 &gic0 0 0 0 25 4>, /* INTB */ + <0 0 0 3 &gic0 0 0 0 26 4>, /* INTC */ + <0 0 0 4 &gic0 0 0 0 27 4>; /* INTD */ + }; diff --git a/Documentation/devicetree/bindings/pci/xilinx-nwl-pcie.txt b/Documentation/devicetree/bindings/pci/xilinx-nwl-pcie.txt new file mode 100644 index 0000000..337fc97 --- /dev/null +++ b/Documentation/devicetree/bindings/pci/xilinx-nwl-pcie.txt @@ -0,0 +1,68 @@ +* Xilinx NWL PCIe Root Port Bridge DT description + +Required properties: +- compatible: Should contain "xlnx,nwl-pcie-2.11" +- #address-cells: Address representation for root ports, set to <3> +- #size-cells: Size representation for root ports, set to <2> +- #interrupt-cells: specifies the number of cells needed to encode an + interrupt source. The value must be 1. +- reg: Should contain Bridge, PCIe Controller registers location, + configuration space, and length +- reg-names: Must include the following entries: + "breg": bridge registers + "pcireg": PCIe controller registers + "cfg": configuration space region +- device_type: must be "pci" +- interrupts: Should contain NWL PCIe interrupt +- interrupt-names: Must include the following entries: + "msi1, msi0": interrupt asserted when MSI is received + "intx": interrupt asserted when a legacy interrupt is received + "misc": interrupt asserted when miscellaneous is received +- interrupt-map-mask and interrupt-map: standard PCI properties to define the + mapping of the PCI interface to interrupt numbers. +- ranges: ranges for the PCI memory regions (I/O space region is not + supported by hardware) + Please refer to the standard PCI bus binding document for a more + detailed explanation +- msi-controller: indicates that this is MSI controller node +- msi-parent: MSI parent of the root complex itself +- legacy-interrupt-controller: Interrupt controller device node for Legacy interrupts + - interrupt-controller: identifies the node as an interrupt controller + - #interrupt-cells: should be set to 1 + - #address-cells: specifies the number of cells needed to encode an + address. The value must be 0. + + +Example: +++++++++ + +nwl_pcie: pcie@fd0e0000 { + #address-cells = <3>; + #size-cells = <2>; + compatible = "xlnx,nwl-pcie-2.11"; + #interrupt-cells = <1>; + msi-controller; + device_type = "pci"; + interrupt-parent = <&gic>; + interrupts = <0 114 4>, <0 115 4>, <0 116 4>, <0 117 4>, <0 118 4>; + interrupt-names = "msi0", "msi1", "intx", "dummy", "misc"; + interrupt-map-mask = <0x0 0x0 0x0 0x7>; + interrupt-map = <0x0 0x0 0x0 0x1 &pcie_intc 0x1>, + <0x0 0x0 0x0 0x2 &pcie_intc 0x2>, + <0x0 0x0 0x0 0x3 &pcie_intc 0x3>, + <0x0 0x0 0x0 0x4 &pcie_intc 0x4>; + + msi-parent = <&nwl_pcie>; + reg = <0x0 0xfd0e0000 0x0 0x1000>, + <0x0 0xfd480000 0x0 0x1000>, + <0x0 0xe0000000 0x0 0x1000000>; + reg-names = "breg", "pcireg", "cfg"; + ranges = <0x02000000 0x00000000 0xe1000000 0x00000000 0xe1000000 0 0x0f000000>; + + pcie_intc: legacy-interrupt-controller { + interrupt-controller; + #address-cells = <0>; + #interrupt-cells = <1>; + }; + +}; diff --git a/Documentation/devicetree/bindings/pci/xilinx-pcie.txt b/Documentation/devicetree/bindings/pci/xilinx-pcie.txt index 02f979a..fd57a81 100644 --- a/Documentation/devicetree/bindings/pci/xilinx-pcie.txt +++ b/Documentation/devicetree/bindings/pci/xilinx-pcie.txt @@ -17,7 +17,7 @@ Required properties: Please refer to the standard PCI bus binding document for a more detailed explanation -Optional properties: +Optional properties for Zynq/Microblaze: - bus-range: PCI bus numbers covered Interrupt controller child node @@ -38,13 +38,13 @@ the four INTx interrupts in ISR and route them to this domain. Example: ++++++++ - +Zynq: pci_express: axi-pcie@50000000 { #address-cells = <3>; #size-cells = <2>; #interrupt-cells = <1>; compatible = "xlnx,axi-pcie-host-1.00.a"; - reg = < 0x50000000 0x10000000 >; + reg = < 0x50000000 0x1000000 >; device_type = "pci"; interrupts = < 0 52 4 >; interrupt-map-mask = <0 0 0 7>; @@ -60,3 +60,29 @@ Example: #interrupt-cells = <1>; }; }; + + +Microblaze: + pci_express: axi-pcie@10000000 { + #address-cells = <3>; + #size-cells = <2>; + #interrupt-cells = <1>; + compatible = "xlnx,axi-pcie-host-1.00.a"; + reg = <0x10000000 0x4000000>; + device_type = "pci"; + interrupt-parent = <µblaze_0_intc>; + interrupts = <1 2>; + interrupt-map-mask = <0 0 0 7>; + interrupt-map = <0 0 0 1 &pcie_intc 1>, + <0 0 0 2 &pcie_intc 2>, + <0 0 0 3 &pcie_intc 3>, + <0 0 0 4 &pcie_intc 4>; + ranges = <0x02000000 0x00000000 0x80000000 0x80000000 0x00000000 0x10000000>; + + pcie_intc: interrupt-controller { + interrupt-controller; + #address-cells = <0>; + #interrupt-cells = <1>; + }; + + }; diff --git a/Documentation/devicetree/bindings/phy/rcar-gen3-phy-usb2.txt b/Documentation/devicetree/bindings/phy/rcar-gen3-phy-usb2.txt index 2390e4e..eaf7e9b 100644 --- a/Documentation/devicetree/bindings/phy/rcar-gen3-phy-usb2.txt +++ b/Documentation/devicetree/bindings/phy/rcar-gen3-phy-usb2.txt @@ -7,33 +7,26 @@ Required properties: - compatible: "renesas,usb2-phy-r8a7795" if the device is a part of an R8A7795 SoC. - reg: offset and length of the partial USB 2.0 Host register block. -- reg-names: must be "usb2_host". - clocks: clock phandle and specifier pair(s). - #phy-cells: see phy-bindings.txt in the same directory, must be <0>. Optional properties: To use a USB channel where USB 2.0 Host and HSUSB (USB 2.0 Peripheral) are -combined, the device tree node should set HSUSB properties to reg and reg-names -properties. This is because HSUSB has registers to select USB 2.0 host or -peripheral at that channel: -- reg: offset and length of the partial HSUSB register block. -- reg-names: must be "hsusb". +combined, the device tree node should set interrupt properties to use the +channel as USB OTG: - interrupts: interrupt specifier for the PHY. Example (R-Car H3): usb-phy@ee080200 { compatible = "renesas,usb2-phy-r8a7795"; - reg = <0 0xee080200 0 0x700>, <0 0xe6590100 0 0x100>; - reg-names = "usb2_host", "hsusb"; + reg = <0 0xee080200 0 0x700>; interrupts = <GIC_SPI 108 IRQ_TYPE_LEVEL_HIGH>; - clocks = <&mstp7_clks R8A7795_CLK_EHCI0>, - <&mstp7_clks R8A7795_CLK_HSUSB>; + clocks = <&mstp7_clks R8A7795_CLK_EHCI0>; }; usb-phy@ee0a0200 { compatible = "renesas,usb2-phy-r8a7795"; reg = <0 0xee0a0200 0 0x700>; - reg-names = "usb2_host"; clocks = <&mstp7_clks R8A7795_CLK_EHCI0>; }; diff --git a/Documentation/devicetree/bindings/phy/rockchip-dp-phy.txt b/Documentation/devicetree/bindings/phy/rockchip-dp-phy.txt new file mode 100644 index 0000000..e3b4809 --- /dev/null +++ b/Documentation/devicetree/bindings/phy/rockchip-dp-phy.txt @@ -0,0 +1,26 @@ +Rockchip specific extensions to the Analogix Display Port PHY +------------------------------------ + +Required properties: +- compatible : should be one of the following supported values: + - "rockchip.rk3288-dp-phy" +- clocks: from common clock binding: handle to dp clock. + of memory mapped region. +- clock-names: from common clock binding: + Required elements: "24m" +- #phy-cells : from the generic PHY bindings, must be 0; + +Example: + +grf: syscon@ff770000 { + compatible = "rockchip,rk3288-grf", "syscon", "simple-mfd"; + +... + + edp_phy: edp-phy { + compatible = "rockchip,rk3288-dp-phy"; + clocks = <&cru SCLK_EDP_24M>; + clock-names = "24m"; + #phy-cells = <0>; + }; +}; diff --git a/Documentation/devicetree/bindings/phy/rockchip-emmc-phy.txt b/Documentation/devicetree/bindings/phy/rockchip-emmc-phy.txt new file mode 100644 index 0000000..555cb0f --- /dev/null +++ b/Documentation/devicetree/bindings/phy/rockchip-emmc-phy.txt @@ -0,0 +1,25 @@ +Rockchip EMMC PHY +----------------------- + +Required properties: + - compatible: rockchip,rk3399-emmc-phy + - #phy-cells: must be 0 + - reg: PHY register address offset and length in "general + register files" + +Example: + + +grf: syscon@ff770000 { + compatible = "rockchip,rk3399-grf", "syscon", "simple-mfd"; + #address-cells = <1>; + #size-cells = <1>; + +... + + emmcphy: phy@f780 { + compatible = "rockchip,rk3399-emmc-phy"; + reg = <0xf780 0x20>; + #phy-cells = <0>; + }; +}; diff --git a/Documentation/devicetree/bindings/pinctrl/allwinner,sunxi-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/allwinner,sunxi-pinctrl.txt index 9213b27..6961722 100644 --- a/Documentation/devicetree/bindings/pinctrl/allwinner,sunxi-pinctrl.txt +++ b/Documentation/devicetree/bindings/pinctrl/allwinner,sunxi-pinctrl.txt @@ -21,6 +21,8 @@ Required properties: "allwinner,sun9i-a80-r-pinctrl" "allwinner,sun8i-a83t-pinctrl" "allwinner,sun8i-h3-pinctrl" + "allwinner,sun8i-h3-r-pinctrl" + "allwinner,sun50i-a64-pinctrl" - reg: Should contain the register physical address and length for the pin controller. diff --git a/Documentation/devicetree/bindings/pinctrl/brcm,ns2-pinmux.txt b/Documentation/devicetree/bindings/pinctrl/brcm,ns2-pinmux.txt new file mode 100644 index 0000000..e295dda --- /dev/null +++ b/Documentation/devicetree/bindings/pinctrl/brcm,ns2-pinmux.txt @@ -0,0 +1,102 @@ +Broadcom Northstar2 IOMUX Controller + +The Northstar2 IOMUX controller supports group based mux configuration. There +are some individual pins that support modifying the pinconf parameters. + +Required properties: + +- compatible: + Must be "brcm,ns2-pinmux" + +- reg: + Define the base and range of the I/O address space that contains the + Northstar2 IOMUX and pin configuration registers. + +Properties in sub nodes: + +- function: + The mux function to select + +- groups: + The list of groups to select with a given function + +- pins: + List of pin names to change configuration + +The generic properties bias-disable, bias-pull-down, bias-pull-up, +drive-strength, slew-rate, input-enable, input-disable are supported +for some individual pins listed at the end. + +For more details, refer to +Documentation/devicetree/bindings/pinctrl/pinctrl-bindings.txt + +For example: + + pinctrl: pinctrl@6501d130 { + compatible = "brcm,ns2-pinmux"; + reg = <0x6501d130 0x08>, + <0x660a0028 0x04>, + <0x660009b0 0x40>; + + pinctrl-names = "default"; + pinctrl-0 = <&nand_sel &uart3_rx &sdio0_d4>; + + /* Select nand function */ + nand_sel: nand_sel { + function = "nand"; + groups = "nand_grp"; + }; + + /* Pull up the uart3 rx pin */ + uart3_rx: uart3_rx { + pins = "uart3_sin"; + bias-pull-up; + }; + + /* Set the drive strength of sdio d4 pin */ + sdio0_d4: sdio0_d4 { + pins = "sdio0_data4"; + drive-strength = <8>; + }; + }; + +List of supported functions and groups in Northstar2: + +"nand": "nand_grp" + +"nor": "nor_data_grp", "nor_adv_grp", "nor_addr_0_3_grp", "nor_addr_4_5_grp", + "nor_addr_6_7_grp", "nor_addr_8_9_grp", "nor_addr_10_11_grp", + "nor_addr_12_15_grp" + +"gpio": "gpio_0_1_grp", "gpio_2_5_grp", "gpio_6_7_grp", "gpio_8_9_grp", + "gpio_10_11_grp", "gpio_12_13_grp", "gpio_14_17_grp", "gpio_18_19_grp", + "gpio_20_21_grp", "gpio_22_23_grp", "gpio_24_25_grp", "gpio_26_27_grp", + "gpio_28_29_grp", "gpio_30_31_grp" + +"pcie": "pcie_ab1_clk_wak_grp", "pcie_a3_clk_wak_grp", "pcie_b3_clk_wak_grp", + "pcie_b2_clk_wak_grp", "pcie_a2_clk_wak_grp" + +"uart0": "uart0_modem_grp", "uart0_rts_cts_grp", "uart0_in_out_grp" + +"uart1": "uart1_ext_clk_grp", "uart1_dcd_dsr_grp", "uart1_ri_dtr_grp", + "uart1_rts_cts_grp", "uart1_in_out_grp" + +"uart2": "uart2_rts_cts_grp" + +"pwm": "pwm_0_grp", "pwm_1_grp", "pwm_2_grp", "pwm_3_grp" + + +List of pins that support pinconf parameters: + +"qspi_wp", "qspi_hold", "qspi_cs", "qspi_sck", "uart3_sin", "uart3_sout", +"qspi_mosi", "qspi_miso", "spi0_fss", "spi0_rxd", "spi0_txd", "spi0_sck", +"spi1_fss", "spi1_rxd", "spi1_txd", "spi1_sck", "sdio0_data7", +"sdio0_emmc_rst", "sdio0_led_on", "sdio0_wp", "sdio0_data3", "sdio0_data4", +"sdio0_data5", "sdio0_data6", "sdio0_cmd", "sdio0_data0", "sdio0_data1", +"sdio0_data2", "sdio1_led_on", "sdio1_wp", "sdio0_cd_l", "sdio0_clk", +"sdio1_data5", "sdio1_data6", "sdio1_data7", "sdio1_emmc_rst", "sdio1_data1", +"sdio1_data2", "sdio1_data3", "sdio1_data4", "sdio1_cd_l", "sdio1_clk", +"sdio1_cmd", "sdio1_data0", "ext_mdio_0", "ext_mdc_0", "usb3_p1_vbus_ppc", +"usb3_p1_overcurrent", "usb3_p0_vbus_ppc", "usb3_p0_overcurrent", +"usb2_presence_indication", "usb2_vbus_present", "usb2_vbus_ppc", +"usb2_overcurrent", "sata_led1", "sata_led0" diff --git a/Documentation/devicetree/bindings/pinctrl/img,pistachio-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/img,pistachio-pinctrl.txt index 08a4a32..0326154 100644 --- a/Documentation/devicetree/bindings/pinctrl/img,pistachio-pinctrl.txt +++ b/Documentation/devicetree/bindings/pinctrl/img,pistachio-pinctrl.txt @@ -134,12 +134,12 @@ mfio80 ddr_debug, mips_trace_data, mips_debug mfio81 dreq0, mips_trace_data, eth_debug mfio82 dreq1, mips_trace_data, eth_debug mfio83 mips_pll_lock, mips_trace_data, usb_debug -mfio84 sys_pll_lock, mips_trace_data, usb_debug -mfio85 wifi_pll_lock, mips_trace_data, sdhost_debug -mfio86 bt_pll_lock, mips_trace_data, sdhost_debug -mfio87 rpu_v_pll_lock, dreq2, socif_debug -mfio88 rpu_l_pll_lock, dreq3, socif_debug -mfio89 audio_pll_lock, dreq4, dreq5 +mfio84 audio_pll_lock, mips_trace_data, usb_debug +mfio85 rpu_v_pll_lock, mips_trace_data, sdhost_debug +mfio86 rpu_l_pll_lock, mips_trace_data, sdhost_debug +mfio87 sys_pll_lock, dreq2, socif_debug +mfio88 wifi_pll_lock, dreq3, socif_debug +mfio89 bt_pll_lock, dreq4, dreq5 tck trstn tdi diff --git a/Documentation/devicetree/bindings/pinctrl/marvell,armada-370-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/marvell,armada-370-pinctrl.txt index add7c38..8662f3a 100644 --- a/Documentation/devicetree/bindings/pinctrl/marvell,armada-370-pinctrl.txt +++ b/Documentation/devicetree/bindings/pinctrl/marvell,armada-370-pinctrl.txt @@ -91,6 +91,9 @@ mpp60 60 gpio, dev(ale1), uart1(rxd), sata0(prsnt), pcie(rstout), mpp61 61 gpo, dev(we1), uart1(txd), audio(lrclk) mpp62 62 gpio, dev(a2), uart1(cts), tdm(drx), pcie(clkreq0), audio(mclk), uart0(cts) -mpp63 63 gpo, spi0(sck), tclk +mpp63 63 gpio, spi0(sck), tclk mpp64 64 gpio, spi0(miso), spi0(cs1) mpp65 65 gpio, spi0(mosi), spi0(cs2) + +Note: According to the datasheet mpp63 is a gpo but there is at least +one example of a gpio usage on the board D-Link DNS-327L diff --git a/Documentation/devicetree/bindings/pinctrl/meson,pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/meson,pinctrl.txt index 3f6a524..32f4a2d 100644 --- a/Documentation/devicetree/bindings/pinctrl/meson,pinctrl.txt +++ b/Documentation/devicetree/bindings/pinctrl/meson,pinctrl.txt @@ -1,13 +1,16 @@ == Amlogic Meson pinmux controller == Required properties for the root node: - - compatible: "amlogic,meson8-pinctrl" or "amlogic,meson8b-pinctrl" + - compatible: one of "amlogic,meson8-cbus-pinctrl" + "amlogic,meson8b-cbus-pinctrl" + "amlogic,meson8-aobus-pinctrl" + "amlogic,meson8b-aobus-pinctrl" - reg: address and size of registers controlling irq functionality === GPIO sub-nodes === -The 2 power domains of the controller (regular and always-on) are -represented as sub-nodes and each of them acts as a GPIO controller. +The GPIO bank for the controller is represented as a sub-node and it acts as a +GPIO controller. Required properties for sub-nodes are: - reg: should contain address and size for mux, pull-enable, pull and @@ -18,10 +21,6 @@ Required properties for sub-nodes are: - gpio-controller: identifies the node as a gpio controller - #gpio-cells: must be 2 -Valid sub-node names are: - - "banks" for the regular domain - - "ao-bank" for the always-on domain - === Other sub-nodes === Child nodes without the "gpio-controller" represent some desired @@ -45,7 +44,7 @@ pinctrl-bindings.txt === Example === pinctrl: pinctrl@c1109880 { - compatible = "amlogic,meson8-pinctrl"; + compatible = "amlogic,meson8-cbus-pinctrl"; reg = <0xc1109880 0x10>; #address-cells = <1>; #size-cells = <1>; @@ -61,15 +60,6 @@ pinctrl-bindings.txt #gpio-cells = <2>; }; - gpio_ao: ao-bank@c1108030 { - reg = <0xc8100014 0x4>, - <0xc810002c 0x4>, - <0xc8100024 0x8>; - reg-names = "mux", "pull", "gpio"; - gpio-controller; - #gpio-cells = <2>; - }; - nand { mux { groups = "nand_io", "nand_io_ce0", "nand_io_ce1", @@ -79,18 +69,4 @@ pinctrl-bindings.txt function = "nand"; }; }; - - uart_ao_a { - mux { - groups = "uart_tx_ao_a", "uart_rx_ao_a", - "uart_cts_ao_a", "uart_rts_ao_a"; - function = "uart_ao"; - }; - - conf { - pins = "GPIOAO_0", "GPIOAO_1", - "GPIOAO_2", "GPIOAO_3"; - bias-disable; - }; - }; }; diff --git a/Documentation/devicetree/bindings/pinctrl/microchip,pic32-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/microchip,pic32-pinctrl.txt new file mode 100644 index 0000000..4b5efa5 --- /dev/null +++ b/Documentation/devicetree/bindings/pinctrl/microchip,pic32-pinctrl.txt @@ -0,0 +1,60 @@ +* Microchip PIC32 Pin Controller + +Please refer to pinctrl-bindings.txt, ../gpio/gpio.txt, and +../interrupt-controller/interrupts.txt for generic information regarding +pin controller, GPIO, and interrupt bindings. + +PIC32 'pin configuration node' is a node of a group of pins which can be +used for a specific device or function. This node represents configuraions of +pins, optional function, and optional mux related configuration. + +Required properties for pin controller node: + - compatible: "microchip,pic32mada-pinctrl" + - reg: Address range of the pinctrl registers. + - clocks: Clock specifier (see clock bindings for details) + +Required properties for pin configuration sub-nodes: + - pins: List of pins to which the configuration applies. + +Optional properties for pin configuration sub-nodes: +---------------------------------------------------- + - function: Mux function for the specified pins. + - bias-pull-up: Enable weak pull-up. + - bias-pull-down: Enable weak pull-down. + - input-enable: Set the pin as an input. + - output-low: Set the pin as an output level low. + - output-high: Set the pin as an output level high. + - microchip,digital: Enable digital I/O. + - microchip,analog: Enable analog I/O. + +Example: + +pic32_pinctrl: pinctrl@1f801400{ + #address-cells = <1>; + #size-cells = <1>; + compatible = "microchip,pic32mzda-pinctrl"; + reg = <0x1f801400 0x400>; + clocks = <&PBCLK1>; + + pinctrl_uart2: pinctrl_uart2 { + uart2-tx { + pins = "G9"; + function = "U2TX"; + microchip,digital; + output-low; + }; + uart2-rx { + pins = "B0"; + function = "U2RX"; + microchip,digital; + input-enable; + }; + }; +}; + +uart2: serial@1f822200 { + compatible = "microchip,pic32mzda-uart"; + reg = <0x1f822200 0x50>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_uart2>; +}; diff --git a/Documentation/devicetree/bindings/pinctrl/nxp,lpc1850-scu.txt b/Documentation/devicetree/bindings/pinctrl/nxp,lpc1850-scu.txt index df0309c..bd8b0c6 100644 --- a/Documentation/devicetree/bindings/pinctrl/nxp,lpc1850-scu.txt +++ b/Documentation/devicetree/bindings/pinctrl/nxp,lpc1850-scu.txt @@ -22,6 +22,10 @@ The following generic nodes are supported: - input-schmitt-disable - slew-rate +NXP specific properties: + - nxp,gpio-pin-interrupt : Assign pin to gpio pin interrupt controller + irq number 0 to 7. See example below. + Not all pins support all properties so either refer to the NXP 1850/4350 user manual or the pin table in the pinctrl-lpc18xx driver for supported pin properties. @@ -54,4 +58,14 @@ pinctrl: pinctrl@40086000 { bias-disable; }; }; + + gpio_joystick_pins: gpio-joystick-pins { + gpio_joystick_1_cfg { + pins = "p9_0"; + function = "gpio"; + nxp,gpio-pin-interrupt = <0>; + input-enable; + bias-disable; + }; + }; }; diff --git a/Documentation/devicetree/bindings/pinctrl/pinctrl-mt65xx.txt b/Documentation/devicetree/bindings/pinctrl/pinctrl-mt65xx.txt index 9ffb0b2..17631d0 100644 --- a/Documentation/devicetree/bindings/pinctrl/pinctrl-mt65xx.txt +++ b/Documentation/devicetree/bindings/pinctrl/pinctrl-mt65xx.txt @@ -6,6 +6,7 @@ Required properties: - compatible: value should be one of the following. "mediatek,mt2701-pinctrl", compatible with mt2701 pinctrl. "mediatek,mt6397-pinctrl", compatible with mt6397 pinctrl. + "mediatek,mt7623-pinctrl", compatible with mt7623 pinctrl. "mediatek,mt8127-pinctrl", compatible with mt8127 pinctrl. "mediatek,mt8135-pinctrl", compatible with mt8135 pinctrl. "mediatek,mt8173-pinctrl", compatible with mt8173 pinctrl. diff --git a/Documentation/devicetree/bindings/pinctrl/qcom,ipq4019-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/qcom,ipq4019-pinctrl.txt new file mode 100644 index 0000000..cfb8500 --- /dev/null +++ b/Documentation/devicetree/bindings/pinctrl/qcom,ipq4019-pinctrl.txt @@ -0,0 +1,74 @@ +Qualcomm Atheros IPQ4019 TLMM block + +This is the Top Level Mode Multiplexor block found on the Qualcomm IPQ8019 +platform, it provides pinctrl, pinmux, pinconf, and gpiolib facilities. + +Required properties: +- compatible: "qcom,ipq4019-pinctrl" +- reg: Should be the base address and length of the TLMM block. +- interrupts: Should be the parent IRQ of the TLMM block. +- interrupt-controller: Marks the device node as an interrupt controller. +- #interrupt-cells: Should be two. +- gpio-controller: Marks the device node as a GPIO controller. +- #gpio-cells : Should be two. + The first cell is the gpio pin number and the + second cell is used for optional parameters. + +Please refer to ../gpio/gpio.txt and ../interrupt-controller/interrupts.txt for +a general description of GPIO and interrupt bindings. + +Please refer to pinctrl-bindings.txt in this directory for details of the +common pinctrl bindings used by client devices, including the meaning of the +phrase "pin configuration node". + +The pin configuration nodes act as a container for an abitrary number of +subnodes. Each of these subnodes represents some desired configuration for a +pin, a group, or a list of pins or groups. This configuration can include the +mux function to select on those pin(s)/group(s), and various pin configuration +parameters, such as pull-up, drive strength, etc. + +The name of each subnode is not important; all subnodes should be enumerated +and processed purely based on their content. + +Each subnode only affects those parameters that are explicitly listed. In +other words, a subnode that lists a mux function but no pin configuration +parameters implies no information about any pin configuration parameters. +Similarly, a pin subnode that describes a pullup parameter implies no +information about e.g. the mux function. + + +The following generic properties as defined in pinctrl-bindings.txt are valid +to specify in a pin configuration subnode: + pins, function, bias-disable, bias-pull-down, bias-pull,up, drive-strength. + +Non-empty subnodes must specify the 'pins' property. +Note that not all properties are valid for all pins. + + +Valid values for qcom,pins are: + gpio0-gpio99 + Supports mux, bias and drive-strength + +Valid values for qcom,function are: +gpio, blsp_uart1, blsp_i2c0, blsp_i2c1, blsp_uart0, blsp_spi1, blsp_spi0 + +Example: + + tlmm: pinctrl@1000000 { + compatible = "qcom,ipq4019-pinctrl"; + reg = <0x1000000 0x300000>; + + gpio-controller; + #gpio-cells = <2>; + interrupt-controller; + #interrupt-cells = <2>; + interrupts = <0 208 0>; + + serial_pins: serial_pinmux { + mux { + pins = "gpio60", "gpio61"; + function = "blsp_uart0"; + bias-disable; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/pinctrl/rockchip,pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/rockchip,pinctrl.txt index 0cd701b..c68b955 100644 --- a/Documentation/devicetree/bindings/pinctrl/rockchip,pinctrl.txt +++ b/Documentation/devicetree/bindings/pinctrl/rockchip,pinctrl.txt @@ -22,7 +22,7 @@ Required properties for iomux controller: - compatible: one of "rockchip,rk2928-pinctrl", "rockchip,rk3066a-pinctrl" "rockchip,rk3066b-pinctrl", "rockchip,rk3188-pinctrl" "rockchip,rk3228-pinctrl", "rockchip,rk3288-pinctrl" - "rockchip,rk3368-pinctrl" + "rockchip,rk3368-pinctrl", "rockchip,rk3399-pinctrl" - rockchip,grf: phandle referencing a syscon providing the "general register files" diff --git a/Documentation/devicetree/bindings/pinctrl/st,stm32-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/st,stm32-pinctrl.txt new file mode 100644 index 0000000..7b4800c --- /dev/null +++ b/Documentation/devicetree/bindings/pinctrl/st,stm32-pinctrl.txt @@ -0,0 +1,126 @@ +* STM32 GPIO and Pin Mux/Config controller + +STMicroelectronics's STM32 MCUs intregrate a GPIO and Pin mux/config hardware +controller. It controls the input/output settings on the available pins and +also provides ability to multiplex and configure the output of various on-chip +controllers onto these pads. + +Pin controller node: +Required properies: + - compatible: value should be one of the following: + (a) "st,stm32f429-pinctrl" + - #address-cells: The value of this property must be 1 + - #size-cells : The value of this property must be 1 + - ranges : defines mapping between pin controller node (parent) to + gpio-bank node (children). + - pins-are-numbered: Specify the subnodes are using numbered pinmux to + specify pins. + +GPIO controller/bank node: +Required properties: + - gpio-controller : Indicates this device is a GPIO controller + - #gpio-cells : Should be two. + The first cell is the pin number + The second one is the polarity: + - 0 for active high + - 1 for active low + - reg : The gpio address range, relative to the pinctrl range + - clocks : clock that drives this bank + - st,bank-name : Should be a name string for this bank as specified in + the datasheet + +Optional properties: + - reset: : Reference to the reset controller + +Example: +#include <dt-bindings/pinctrl/stm32f429-pinfunc.h> +... + + pin-controller { + #address-cells = <1>; + #size-cells = <1>; + compatible = "st,stm32f429-pinctrl"; + ranges = <0 0x40020000 0x3000>; + pins-are-numbered; + + gpioa: gpio@40020000 { + gpio-controller; + #gpio-cells = <2>; + reg = <0x0 0x400>; + resets = <&reset_ahb1 0>; + st,bank-name = "GPIOA"; + }; + ... + pin-functions nodes follow... + }; + +Contents of function subnode node: +---------------------------------- +Subnode format +A pinctrl node should contain at least one subnode representing the +pinctrl group available on the machine. Each subnode will list the +pins it needs, and how they should be configured, with regard to muxer +configuration, pullups, drive, output high/low and output speed. + + node { + pinmux = <PIN_NUMBER_PINMUX>; + GENERIC_PINCONFIG; + }; + +Required properties: +- pinmux: integer array, represents gpio pin number and mux setting. + Supported pin number and mux varies for different SoCs, and are defined in + dt-bindings/pinctrl/<soc>-pinfunc.h directly. + These defines are calculated as: + ((port * 16 + line) << 8) | function + With: + - port: The gpio port index (PA = 0, PB = 1, ..., PK = 11) + - line: The line offset within the port (PA0 = 0, PA1 = 1, ..., PA15 = 15) + - function: The function number, can be: + * 0 : GPIO + * 1 : Alternate Function 0 + * 2 : Alternate Function 1 + * 3 : Alternate Function 2 + * ... + * 16 : Alternate Function 15 + * 17 : Analog + +Optional properties: +- GENERIC_PINCONFIG: is the generic pinconfig options to use. + Available options are: + - bias-disable, + - bias-pull-down, + - bias-pull-up, + - drive-push-pull, + - drive-open-drain, + - output-low + - output-high + - slew-rate = <x>, with x being: + < 0 > : Low speed + < 1 > : Medium speed + < 2 > : Fast speed + < 3 > : High speed + +Example: + +pin-controller { +... + usart1_pins_a: usart1@0 { + pins1 { + pinmux = <STM32F429_PA9_FUNC_USART1_TX>; + bias-disable; + drive-push-pull; + slew-rate = <0>; + }; + pins2 { + pinmux = <STM32F429_PA10_FUNC_USART1_RX>; + bias-disable; + }; + }; +}; + +&usart1 { + pinctrl-0 = <&usart1_pins_a>; + pinctrl-names = "default"; + status = "okay"; +}; diff --git a/Documentation/devicetree/bindings/power/act8945a-charger.txt b/Documentation/devicetree/bindings/power/act8945a-charger.txt new file mode 100644 index 0000000..bea254c --- /dev/null +++ b/Documentation/devicetree/bindings/power/act8945a-charger.txt @@ -0,0 +1,35 @@ +Device-Tree bindings for charger of Active-semi ACT8945A Multi-Function Device + +Required properties: + - compatible: "active-semi,act8945a", please refer to ../mfd/act8945a.txt. + - active-semi,chglev-gpios: charge current level phandle with args + as described in ../gpio/gpio.txt. + +Optional properties: + - active-semi,check-battery-temperature: boolean to check the battery + temperature or not. + - active-semi,input-voltage-threshold-microvolt: unit: mV; + Specifies the charger's input over-voltage threshold value; + The value can be: 6600, 7000, 7500, 8000; default: 6600 + - active-semi,precondition-timeout: unit: minutes; + Specifies the charger's PRECONDITION safety timer setting value; + The value can be: 40, 60, 80, 0; If 0, it means to disable this timer; + default: 40. + - active-semi,total-timeout: unit: hours; + Specifies the charger's total safety timer setting value; + The value can be: 3, 4, 5, 0; If 0, it means to disable this timer; + default: 3. + +Example: + pmic@5b { + compatible = "active-semi,act8945a"; + reg = <0x5b>; + status = "okay"; + + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_charger_chglev>; + active-semi,chglev-gpios = <&pioA 12 GPIO_ACTIVE_HIGH>; + active-semi,input-voltage-threshold-microvolt = <6600>; + active-semi,precondition-timeout = <40>; + active-semi,total-timeout = <3>; + }; diff --git a/Documentation/devicetree/bindings/power/rockchip-io-domain.txt b/Documentation/devicetree/bindings/power/rockchip-io-domain.txt index b8627e7..c84fb47 100644 --- a/Documentation/devicetree/bindings/power/rockchip-io-domain.txt +++ b/Documentation/devicetree/bindings/power/rockchip-io-domain.txt @@ -35,6 +35,8 @@ Required properties: - "rockchip,rk3288-io-voltage-domain" for rk3288 - "rockchip,rk3368-io-voltage-domain" for rk3368 - "rockchip,rk3368-pmu-io-voltage-domain" for rk3368 pmu-domains + - "rockchip,rk3399-io-voltage-domain" for rk3399 + - "rockchip,rk3399-pmu-io-voltage-domain" for rk3399 pmu-domains - rockchip,grf: phandle to the syscon managing the "general register files" @@ -79,6 +81,15 @@ Possible supplies for rk3368 pmu-domains: - pmu-supply: The supply connected to PMUIO_VDD. - vop-supply: The supply connected to LCDC_VDD. +Possible supplies for rk3399: +- bt656-supply: The supply connected to APIO2_VDD. +- audio-supply: The supply connected to APIO5_VDD. +- sdmmc-supply: The supply connected to SDMMC0_VDD. +- gpio1830 The supply connected to APIO4_VDD. + +Possible supplies for rk3399 pmu-domains: +- pmu1830-supply:The supply connected to PMUIO2_VDD. + Example: io-domains { diff --git a/Documentation/devicetree/bindings/power_supply/ti,bq24735.txt b/Documentation/devicetree/bindings/power_supply/ti,bq24735.txt index 4f6a550..3bf5575 100644 --- a/Documentation/devicetree/bindings/power_supply/ti,bq24735.txt +++ b/Documentation/devicetree/bindings/power_supply/ti,bq24735.txt @@ -22,6 +22,9 @@ Optional properties : value must be between 128mA and 8.064A with a 128mA step resolution. The POR value is 0x1000h. This number is in mA (e.g. 8064), see the spec for more information about the InputCurrent (0x3fh) register. + - ti,external-control : Indicates that the charger is configured externally + and that the host should not attempt to enable/disable charging or set the + charge voltage/current. Example: diff --git a/Documentation/devicetree/bindings/powerpc/fsl/fman.txt b/Documentation/devicetree/bindings/powerpc/fsl/fman.txt index 1fc5328..55c2c03 100644 --- a/Documentation/devicetree/bindings/powerpc/fsl/fman.txt +++ b/Documentation/devicetree/bindings/powerpc/fsl/fman.txt @@ -315,6 +315,16 @@ PROPERTIES Value type: <phandle> Definition: A phandle for 1EEE1588 timer. +- pcsphy-handle + Usage required for "fsl,fman-memac" MACs + Value type: <phandle> + Definition: A phandle for pcsphy. + +- tbi-handle + Usage required for "fsl,fman-dtsec" MACs + Value type: <phandle> + Definition: A phandle for tbiphy. + EXAMPLE fman1_tx28: port@a8000 { @@ -340,6 +350,7 @@ ethernet@e0000 { reg = <0xe0000 0x1000>; fsl,fman-ports = <&fman1_rx8 &fman1_tx28>; ptp-timer = <&ptp-timer>; + tbi-handle = <&tbi0>; }; ============================================================================ @@ -415,6 +426,13 @@ PROPERTIES The settings and programming routines for internal/external MDIO are different. Must be included for internal MDIO. +For internal PHY device on internal mdio bus, a PHY node should be created. +See the definition of the PHY node in booting-without-of.txt for an +example of how to define a PHY (Internal PHY has no interrupt line). +- For "fsl,fman-mdio" compatible internal mdio bus, the PHY is TBI PHY. +- For "fsl,fman-memac-mdio" compatible internal mdio bus, the PHY is PCS PHY, + PCS PHY addr must be '0'. + EXAMPLE Example for FMan v2 external MDIO: @@ -425,12 +443,29 @@ mdio@f1000 { interrupts = <101 2 0 0>; }; +Example for FMan v2 internal MDIO: + +mdio@e3120 { + compatible = "fsl,fman-mdio"; + reg = <0xe3120 0xee0>; + fsl,fman-internal-mdio; + + tbi1: tbi-phy@8 { + reg = <0x8>; + device_type = "tbi-phy"; + }; +}; + Example for FMan v3 internal MDIO: mdio@f1000 { compatible = "fsl,fman-memac-mdio"; reg = <0xf1000 0x1000>; fsl,fman-internal-mdio; + + pcsphy6: ethernet-phy@0 { + reg = <0x0>; + }; }; ============================================================================= @@ -568,6 +603,7 @@ fman@400000 { cell-index = <0>; reg = <0xe0000 0x1000>; fsl,fman-ports = <&fman1_rx_0x8 &fman1_tx_0x28>; + tbi-handle = <&tbi5>; }; ethernet@e2000 { @@ -575,6 +611,7 @@ fman@400000 { cell-index = <1>; reg = <0xe2000 0x1000>; fsl,fman-ports = <&fman1_rx_0x9 &fman1_tx_0x29>; + tbi-handle = <&tbi6>; }; ethernet@e4000 { @@ -582,6 +619,7 @@ fman@400000 { cell-index = <2>; reg = <0xe4000 0x1000>; fsl,fman-ports = <&fman1_rx_0xa &fman1_tx_0x2a>; + tbi-handle = <&tbi7>; }; ethernet@e6000 { @@ -589,6 +627,7 @@ fman@400000 { cell-index = <3>; reg = <0xe6000 0x1000>; fsl,fman-ports = <&fman1_rx_0xb &fman1_tx_0x2b>; + tbi-handle = <&tbi8>; }; ethernet@e8000 { @@ -596,6 +635,7 @@ fman@400000 { cell-index = <4>; reg = <0xf0000 0x1000>; fsl,fman-ports = <&fman1_rx_0xc &fman1_tx_0x2c>; + tbi-handle = <&tbi9>; ethernet@f0000 { cell-index = <8>; diff --git a/Documentation/devicetree/bindings/property-units.txt b/Documentation/devicetree/bindings/property-units.txt new file mode 100644 index 0000000..12278d7 --- /dev/null +++ b/Documentation/devicetree/bindings/property-units.txt @@ -0,0 +1,39 @@ +Standard Unit Suffixes for Property names + +Properties which have a unit of measure are recommended to have a unit +suffix appended to the property name. The list below contains the +recommended suffixes. Other variations exist in bindings, but should not +be used in new bindings or added here. The inconsistency in the unit +prefixes is due to selecting the most commonly used variants. + +It is also recommended to use the units listed here and not add additional +unit prefixes. + +Time/Frequency +---------------------------------------- +-mhz : megahertz +-hz : Hertz (preferred) +-sec : seconds +-ms : milliseconds +-us : microseconds +-ns : nanoseconds + +Distance +---------------------------------------- +-mm : millimeters + +Electricity +---------------------------------------- +-microamp : micro amps +-ohms : Ohms +-micro-ohms : micro Ohms +-microvolt : micro volts + +Temperature +---------------------------------------- +-celsius : Degrees Celsius +-millicelsius : Degreee milli-Celsius + +Pressure +---------------------------------------- +-kpascal : kiloPascal diff --git a/Documentation/devicetree/bindings/regmap/regmap.txt b/Documentation/devicetree/bindings/regmap/regmap.txt index b494f8b..0127be3 100644 --- a/Documentation/devicetree/bindings/regmap/regmap.txt +++ b/Documentation/devicetree/bindings/regmap/regmap.txt @@ -1,47 +1,29 @@ -Device-Tree binding for regmap +Devicetree binding for regmap -The endianness mode of CPU & Device scenarios: -Index Device Endianness properties ---------------------------------------------------- -1 BE 'big-endian' -2 LE 'little-endian' +Optional properties: -For one device driver, which will run in different scenarios above -on different SoCs using the devicetree, we need one way to simplify -this. + little-endian, + big-endian, + native-endian: See common-properties.txt for a definition -Required properties: -- {big,little}-endian: these are boolean properties, if absent - meaning that the CPU and the Device are in the same endianness mode, - these properties are for register values and all the buffers only. +Note: +Regmap defaults to little-endian register access on MMIO based +devices, this is by far the most common setting. On CPU +architectures that typically run big-endian operating systems +(e.g. PowerPC), registers can be defined as big-endian and must +be marked that way in the devicetree. -Examples: -Scenario 1 : CPU in LE mode & device in LE mode. -dev: dev@40031000 { - compatible = "name"; - reg = <0x40031000 0x1000>; - ... -}; +On SoCs that can be operated in both big-endian and little-endian +modes, with a single hardware switch controlling both the endianess +of the CPU and a byteswap for MMIO registers (e.g. many Broadcom MIPS +chips), "native-endian" is used to allow using the same device tree +blob in both cases. -Scenario 2 : CPU in LE mode & device in BE mode. +Examples: +Scenario 1 : a register set in big-endian mode. dev: dev@40031000 { - compatible = "name"; + compatible = "syscon"; reg = <0x40031000 0x1000>; - ... big-endian; -}; - -Scenario 3 : CPU in BE mode & device in BE mode. -dev: dev@40031000 { - compatible = "name"; - reg = <0x40031000 0x1000>; - ... -}; - -Scenario 4 : CPU in BE mode & device in LE mode. -dev: dev@40031000 { - compatible = "name"; - reg = <0x40031000 0x1000>; ... - little-endian; }; diff --git a/Documentation/devicetree/bindings/regulator/act8945a-regulator.txt b/Documentation/devicetree/bindings/regulator/act8945a-regulator.txt new file mode 100644 index 0000000..5c80a77 --- /dev/null +++ b/Documentation/devicetree/bindings/regulator/act8945a-regulator.txt @@ -0,0 +1,80 @@ +Device-Tree bindings for regulators of Active-semi ACT8945A Multi-Function Device + +Required properties: + - compatible: "active-semi,act8945a", please refer to ../mfd/act8945a.txt. + +Optional properties: +- active-semi,vsel-high: Indicates if the VSEL pin is set to logic-high. + If this property is missing, assume the VSEL pin is set to logic-low. + +Optional input supply properties: + - vp1-supply: The input supply for REG_DCDC1 + - vp2-supply: The input supply for REG_DCDC2 + - vp3-supply: The input supply for REG_DCDC3 + - inl45-supply: The input supply for REG_LDO1 and REG_LDO2 + - inl67-supply: The input supply for REG_LDO3 and REG_LDO4 + +Any standard regulator properties can be used to configure the single regulator. + +The valid names for regulators are: + REG_DCDC1, REG_DCDC2, REG_DCDC3, REG_LDO1, REG_LDO2, REG_LDO3, REG_LDO4. + +Example: + pmic@5b { + compatible = "active-semi,act8945a"; + reg = <0x5b>; + status = "okay"; + + active-semi,vsel-high; + + regulators { + vdd_1v35_reg: REG_DCDC1 { + regulator-name = "VDD_1V35"; + regulator-min-microvolt = <1350000>; + regulator-max-microvolt = <1350000>; + regulator-always-on; + }; + + vdd_1v2_reg: REG_DCDC2 { + regulator-name = "VDD_1V2"; + regulator-min-microvolt = <1100000>; + regulator-max-microvolt = <1300000>; + regulator-always-on; + }; + + vdd_3v3_reg: REG_DCDC3 { + regulator-name = "VDD_3V3"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-always-on; + }; + + vdd_fuse_reg: REG_LDO1 { + regulator-name = "VDD_FUSE"; + regulator-min-microvolt = <2500000>; + regulator-max-microvolt = <2500000>; + regulator-always-on; + }; + + vdd_3v3_lp_reg: REG_LDO2 { + regulator-name = "VDD_3V3_LP"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-always-on; + }; + + vdd_led_reg: REG_LDO3 { + regulator-name = "VDD_LED"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-always-on; + }; + + vdd_sdhc_1v8_reg: REG_LDO4 { + regulator-name = "VDD_SDHC_1V8"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-always-on; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/regulator/hisilicon,hi655x-regulator.txt b/Documentation/devicetree/bindings/regulator/hisilicon,hi655x-regulator.txt new file mode 100644 index 0000000..14cfdc5 --- /dev/null +++ b/Documentation/devicetree/bindings/regulator/hisilicon,hi655x-regulator.txt @@ -0,0 +1,29 @@ +Hisilicon Hi655x Voltage regulators + +Note: +The Hi655x regulator control is managed by Hi655x PMIC. +So the node of this regulator must be child node of Hi655x +PMIC node. + +The driver uses the regulator core framework, so please also +take the bindings of regulator.txt for reference. + +The valid names for regulators are: + +LDO2_2V8 LDO7_SDIO LDO10_2V85 LDO13_1V8 LDO14_2V8 +LDO15_1V8 LDO17_2V5 LDO19_3V0 LDO21_1V8 LDO22_1V2 + +Example: + pmic: pmic@f8000000 { + compatible = "hisilicon,hi655x-pmic"; + ... + regulators { + ldo2: LDO2@a21 { + regulator-name = "LDO2_2V8"; + regulator-min-microvolt = <2500000>; + regulator-max-microvolt = <3200000>; + regulator-enable-ramp-delay = <120>; + }; + ... + } + } diff --git a/Documentation/devicetree/bindings/regulator/lp872x.txt b/Documentation/devicetree/bindings/regulator/lp872x.txt index 7818318..ca58a68 100644 --- a/Documentation/devicetree/bindings/regulator/lp872x.txt +++ b/Documentation/devicetree/bindings/regulator/lp872x.txt @@ -28,6 +28,7 @@ Optional properties: - ti,dvs-gpio: GPIO specifier for external DVS pin control of LP872x devices. - ti,dvs-vsel: DVS selector. 0 = SEL_V1, 1 = SEL_V2. - ti,dvs-state: initial DVS pin state. 0 = DVS_LOW, 1 = DVS_HIGH. + - enable-gpios: GPIO specifier for EN pin control of LP872x devices. Sub nodes for regulator_init_data LP8720 has maximum 6 nodes. (child name: ldo1 ~ 5 and buck) diff --git a/Documentation/devicetree/bindings/regulator/max77802.txt b/Documentation/devicetree/bindings/regulator/max77802.txt index 09d796e..879e98d 100644 --- a/Documentation/devicetree/bindings/regulator/max77802.txt +++ b/Documentation/devicetree/bindings/regulator/max77802.txt @@ -60,7 +60,7 @@ The possible values for "regulator-initial-mode" and "regulator-mode" are: 1: Normal regulator voltage output mode. 3: Low Power which reduces the quiescent current down to only 1uA -The list of valid modes are defined in the dt-bindings/clock/maxim,max77802.h +The valid modes list is defined in the dt-bindings/regulator/maxim,max77802.h header and can be included by device tree source files. The standard "regulator-mode" property can only be used for regulators that diff --git a/Documentation/devicetree/bindings/regulator/regulator-max77620.txt b/Documentation/devicetree/bindings/regulator/regulator-max77620.txt new file mode 100644 index 0000000..b3c8ca6 --- /dev/null +++ b/Documentation/devicetree/bindings/regulator/regulator-max77620.txt @@ -0,0 +1,200 @@ +Regulator DT binding for MAX77620 Power management IC from Maxim Semiconductor. + +Device has multiple DCDC(sd[0-3] and LDOs(ldo[0-8]). The input supply +of these regulators are defined under parent device node. +Details of regulator properties are defined as child node under +sub-node "regulators" which is child node of device node. + +Please refer file <Documentation/devicetree/bindings/regulator/regulator.txt> +for common regulator bindings used by client. + +Following are properties of parent node related to regulators. + +Optional properties: +------------------- +The input supply of regulators are the optional properties on the +parent device node. The input supply of these regulators are provided +through following properties: +in-sd0-supply: Input supply for SD0, INA-SD0 or INB-SD0 pins. +in-sd1-supply: Input supply for SD1. +in-sd2-supply: Input supply for SD2. +in-sd3-supply: Input supply for SD3. +in-ldo0-1-supply: Input supply for LDO0 and LDO1. +in-ldo2-supply: Input supply for LDO2. +in-ldo3-5-supply: Input supply for LDO3 and LDO5 +in-ldo4-6-supply: Input supply for LDO4 and LDO6. +in-ldo7-8-supply: Input supply for LDO7 and LDO8. + +Optional sub nodes for regulators under "regulators" subnode: +------------------------------------------------------------ +The subnodes name is the name of regulator and it must be one of: + sd[0-3], ldo[0-8] + +Each sub-node should contain the constraints and initialization +information for that regulator. The definition for each of these +nodes is defined using the standard binding for regulators found at +<Documentation/devicetree/bindings/regulator/regulator.txt>. + +Theres are also additional properties for SD/LDOs. These additional properties +are required to configure FPS configuration parameters for SDs and LDOs. +Please refer <devicetree/bindings/mfd/max77620.txt> for more detail of Flexible +Power Sequence (FPS). +Following are additional properties: + +- maxim,active-fps-source: FPS source for the regulators to get + enabled/disabled when system is in + active state. Valid values are: + - MAX77620_FPS_SRC_0, + FPS source is FPS0. + - MAX77620_FPS_SRC_1, + FPS source is FPS1 + - MAX77620_FPS_SRC_2 and + FPS source is FPS2 + - MAX77620_FPS_SRC_NONE. + Regulator is not controlled + by FPS events and it gets + enabled/disabled by register + access. + Absence of this property will leave + the FPS configuration register for that + regulator to default configuration. + +- maxim,active-fps-power-up-slot: Sequencing event slot number on which + the regulator get enabled when + master FPS input event set to HIGH. + Valid values are 0 to 7. + This is applicable if FPS source is + selected as FPS0, FPS1 or FPS2. + +- maxim,active-fps-power-down-slot: Sequencing event slot number on which + the regulator get disabled when master + FPS input event set to LOW. + Valid values are 0 to 7. + This is applicable if FPS source is + selected as FPS0, FPS1 or FPS2. + +- maxim,suspend-fps-source: This is same as property + "maxim,active-fps-source" but value + get configured when system enters in + to suspend state. + +- maxim,suspend-fps-power-up-slot: This is same as property + "maxim,active-fps-power-up-slot" but + this value get configured into FPS + configuration register when system + enters into suspend. + This is applicable if suspend state + FPS source is selected as FPS0, FPS1 or + +- maxim,suspend-fps-power-down-slot: This is same as property + "maxim,active-fps-power-down-slot" but + this value get configured into FPS + configuration register when system + enters into suspend. + This is applicable if suspend state + FPS source is selected as FPS0, FPS1 or + FPS2. + +Example: +-------- +#include <dt-bindings/mfd/max77620.h> +... +max77620@3c { + in-ldo0-1-supply = <&max77620_sd2>; + in-ldo7-8-supply = <&max77620_sd2>; + regulators { + sd0 { + regulator-name = "vdd-core"; + regulator-min-microvolt = <600000>; + regulator-max-microvolt = <1400000>; + regulator-boot-on; + regulator-always-on; + maxim,active-fps-source = <MAX77620_FPS_SRC_1>; + }; + + sd1 { + regulator-name = "vddio-ddr"; + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <1200000>; + regulator-always-on; + regulator-boot-on; + maxim,active-fps-source = <MAX77620_FPS_SRC_0>; + }; + + sd2 { + regulator-name = "vdd-pre-reg"; + regulator-min-microvolt = <1350000>; + regulator-max-microvolt = <1350000>; + }; + + sd3 { + regulator-name = "vdd-1v8"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-always-on; + regulator-boot-on; + }; + + ldo0 { + regulator-name = "avdd-sys"; + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <1200000>; + regulator-always-on; + regulator-boot-on; + }; + + ldo1 { + regulator-name = "vdd-pex"; + regulator-min-microvolt = <1050000>; + regulator-max-microvolt = <1050000>; + }; + + ldo2 { + regulator-name = "vddio-sdmmc3"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <3300000>; + }; + + ldo3 { + regulator-name = "vdd-cam-hv"; + regulator-min-microvolt = <2800000>; + regulator-max-microvolt = <2800000>; + }; + + ldo4 { + regulator-name = "vdd-rtc"; + regulator-min-microvolt = <1250000>; + regulator-max-microvolt = <1250000>; + regulator-always-on; + regulator-boot-on; + }; + + ldo5 { + regulator-name = "avdd-ts-hv"; + regulator-min-microvolt = <3000000>; + regulator-max-microvolt = <3000000>; + }; + + ldo6 { + regulator-name = "vdd-ts"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-always-on; + regulator-boot-on; + }; + + ldo7 { + regulator-name = "vdd-gen-pll-edp"; + regulator-min-microvolt = <1050000>; + regulator-max-microvolt = <1050000>; + regulator-always-on; + regulator-boot-on; + }; + + ldo8 { + regulator-name = "vdd-hdmi-dp"; + regulator-min-microvolt = <1050000>; + regulator-max-microvolt = <1050000>; + }; + }; +}; diff --git a/Documentation/devicetree/bindings/regulator/regulator.txt b/Documentation/devicetree/bindings/regulator/regulator.txt index 1d112fc..ecfc593 100644 --- a/Documentation/devicetree/bindings/regulator/regulator.txt +++ b/Documentation/devicetree/bindings/regulator/regulator.txt @@ -44,6 +44,11 @@ Optional properties: any consumer request. - regulator-pull-down: Enable pull down resistor when the regulator is disabled. - regulator-over-current-protection: Enable over current protection. +- regulator-active-discharge: tristate, enable/disable active discharge of + regulators. The values are: + 0: Disable active discharge. + 1: Enable active discharge. + Absence of this property will leave configuration to default. Deprecated properties: - regulator-compatible: If a regulator chip contains multiple diff --git a/Documentation/devicetree/bindings/remoteproc/st-rproc.txt b/Documentation/devicetree/bindings/remoteproc/st-rproc.txt new file mode 100644 index 0000000..1031bcd --- /dev/null +++ b/Documentation/devicetree/bindings/remoteproc/st-rproc.txt @@ -0,0 +1,41 @@ +STMicroelectronics Co-Processor Bindings +---------------------------------------- + +This binding provides support for adjunct processors found on ST SoCs. + +Co-processors can be controlled from the bootloader or the primary OS. If +the bootloader starts a co-processor, the primary OS must detect its state +and act accordingly. + +Required properties: +- compatible Should be one of: + "st,st231-rproc" + "st,st40-rproc" +- memory-region Reserved memory (See: ../reserved-memory/reserved-memory.txt) +- resets Reset lines (See: ../reset/reset.txt) +- reset-names Must be "sw_reset" and "pwr_reset" +- clocks Clock for co-processor (See: ../clock/clock-bindings.txt) +- clock-frequency Clock frequency to set co-processor at if the bootloader + hasn't already done so +- st,syscfg System configuration register which holds the boot vector + for the co-processor + 1st cell: Phandle to syscon block + 2nd cell: Boot vector register offset + +Example: + + audio_reserved: rproc@42000000 { + compatible = "shared-dma-pool"; + reg = <0x42000000 0x01000000>; + no-map; + }; + + st231-audio { + compatible = "st,st231-rproc"; + memory-region = <&audio_reserved>; + resets = <&softreset STIH407_ST231_AUD_SOFTRESET>; + reset-names = "sw_reset"; + clocks = <&clk_s_c0_flexgen CLK_ST231_AUD_0>; + clock-frequency = <600000000>; + st,syscfg = <&syscfg_core 0x228>; + }; diff --git a/Documentation/devicetree/bindings/reset/img,pistachio-reset.txt b/Documentation/devicetree/bindings/reset/img,pistachio-reset.txt new file mode 100644 index 0000000..8c05d16 --- /dev/null +++ b/Documentation/devicetree/bindings/reset/img,pistachio-reset.txt @@ -0,0 +1,55 @@ +Pistachio Reset Controller +============================================================================= + +This binding describes a reset controller device that is used to enable and +disable individual IP blocks within the Pistachio SoC using "soft reset" +control bits found in the Pistachio SoC top level registers. + +The actual action taken when soft reset is asserted is hardware dependent. +However, when asserted it may not be possible to access the hardware's +registers, and following an assert/deassert sequence the hardware's previous +state may no longer be valid. + +Please refer to Documentation/devicetree/bindings/reset/reset.txt +for common reset controller binding usage. + +Required properties: + +- compatible: Contains "img,pistachio-reset" + +- #reset-cells: Contains 1 + +Example: + + cr_periph: clk@18148000 { + compatible = "img,pistachio-cr-periph", "syscon", "simple-mfd"; + reg = <0x18148000 0x1000>; + clocks = <&clk_periph PERIPH_CLK_SYS>; + clock-names = "sys"; + #clock-cells = <1>; + + pistachio_reset: reset-controller { + compatible = "img,pistachio-reset"; + #reset-cells = <1>; + }; + }; + +Specifying reset control of devices +======================================= + +Device nodes should specify the reset channel required in their "resets" +property, containing a phandle to the pistachio reset device node and an +index specifying which reset to use, as described in +Documentation/devicetree/bindings/reset/reset.txt. + +Example: + + spdif_out: spdif-out@18100d00 { + ... + resets = <&pistachio_reset PISTACHIO_RESET_SPDIF_OUT>; + reset-names = "rst"; + ... + }; + +Macro definitions for the supported resets can be found in: +include/dt-bindings/reset/pistachio-resets.h diff --git a/Documentation/devicetree/bindings/rng/brcm,bcm6368.txt b/Documentation/devicetree/bindings/rng/brcm,bcm6368.txt new file mode 100644 index 0000000..4b5ac60 --- /dev/null +++ b/Documentation/devicetree/bindings/rng/brcm,bcm6368.txt @@ -0,0 +1,17 @@ +BCM6368 Random number generator + +Required properties: + +- compatible : should be "brcm,bcm6368-rng" +- reg : Specifies base physical address and size of the registers +- clocks : phandle to clock-controller plus clock-specifier pair +- clock-names : "ipsec" as a clock name + +Example: + random: rng@10004180 { + compatible = "brcm,bcm6368-rng"; + reg = <0x10004180 0x14>; + + clocks = <&periph_clk 18>; + clock-names = "ipsec"; + }; diff --git a/Documentation/devicetree/bindings/rng/microchip,pic32-rng.txt b/Documentation/devicetree/bindings/rng/microchip,pic32-rng.txt new file mode 100644 index 0000000..c6d1003 --- /dev/null +++ b/Documentation/devicetree/bindings/rng/microchip,pic32-rng.txt @@ -0,0 +1,17 @@ +* Microchip PIC32 Random Number Generator + +The PIC32 RNG provides a pseudo random number generator which can be seeded by +another true random number generator. + +Required properties: +- compatible : should be "microchip,pic32mzda-rng" +- reg : Specifies base physical address and size of the registers. +- clocks: clock phandle. + +Example: + + rng: rng@1f8e6000 { + compatible = "microchip,pic32mzda-rng"; + reg = <0x1f8e6000 0x1000>; + clocks = <&PBCLK5>; + }; diff --git a/Documentation/devicetree/bindings/rtc/alphascale,asm9260-rtc.txt b/Documentation/devicetree/bindings/rtc/alphascale,asm9260-rtc.txt new file mode 100644 index 0000000..76ebca5 --- /dev/null +++ b/Documentation/devicetree/bindings/rtc/alphascale,asm9260-rtc.txt @@ -0,0 +1,19 @@ +* Alphascale asm9260 SoC Real Time Clock + +Required properties: +- compatible: Should be "alphascale,asm9260-rtc" +- reg: Physical base address of the controller and length + of memory mapped region. +- interrupts: IRQ line for the RTC. +- clocks: Reference to the clock entry. +- clock-names: should contain: + * "ahb" for the SoC RTC clock + +Example: +rtc0: rtc@800a0000 { + compatible = "alphascale,asm9260-rtc"; + reg = <0x800a0000 0x100>; + clocks = <&acc CLKID_AHB_RTC>; + clock-names = "ahb"; + interrupts = <2>; +}; diff --git a/Documentation/devicetree/bindings/rtc/epson,rx6110.txt b/Documentation/devicetree/bindings/rtc/epson,rx6110.txt new file mode 100644 index 0000000..3dc313e --- /dev/null +++ b/Documentation/devicetree/bindings/rtc/epson,rx6110.txt @@ -0,0 +1,39 @@ +Epson RX6110 Real Time Clock +============================ + +The Epson RX6110 can be used with SPI or I2C busses. The kind of +bus depends on the SPISEL pin and can not be configured via software. + +I2C mode +-------- + +Required properties: + - compatible: should be: "epson,rx6110" + - reg : the I2C address of the device for I2C + +Example: + + rtc: rtc@32 { + compatible = "epson,rx6110" + reg = <0x32>; + }; + +SPI mode +-------- + +Required properties: + - compatible: should be: "epson,rx6110" + - reg: chip select number + - spi-cs-high: RX6110 needs chipselect high + - spi-cpha: RX6110 works with SPI shifted clock phase + - spi-cpol: RX6110 works with SPI inverse clock polarity + +Example: + + rtc: rtc@3 { + compatible = "epson,rx6110" + reg = <3> + spi-cs-high; + spi-cpha; + spi-cpol; + }; diff --git a/Documentation/devicetree/bindings/rtc/maxim,ds3231.txt b/Documentation/devicetree/bindings/rtc/maxim,ds3231.txt new file mode 100644 index 0000000..ddef330 --- /dev/null +++ b/Documentation/devicetree/bindings/rtc/maxim,ds3231.txt @@ -0,0 +1,37 @@ +* Maxim DS3231 Real Time Clock + +Required properties: +see: Documentation/devicetree/bindings/i2c/trivial-devices.txt + +Optional property: +- #clock-cells: Should be 1. +- clock-output-names: + overwrite the default clock names "ds3231_clk_sqw" and "ds3231_clk_32khz". + +Each clock is assigned an identifier and client nodes can use this identifier +to specify the clock which they consume. Following indices are allowed: + - 0: square-wave output on the SQW pin + - 1: square-wave output on the 32kHz pin + +- interrupts: rtc alarm/event interrupt. When this property is selected, + clock on the SQW pin cannot be used. + +Example: + +ds3231: ds3231@51 { + compatible = "maxim,ds3231"; + reg = <0x68>; + #clock-cells = <1>; +}; + +device1 { +... + clocks = <&ds3231 0>; +... +}; + +device2 { +... + clocks = <&ds3231 1>; +... +}; diff --git a/Documentation/devicetree/bindings/rtc/maxim,mcp795.txt b/Documentation/devicetree/bindings/rtc/maxim,mcp795.txt new file mode 100644 index 0000000..a59fdd8 --- /dev/null +++ b/Documentation/devicetree/bindings/rtc/maxim,mcp795.txt @@ -0,0 +1,11 @@ +* Maxim MCP795 SPI Serial Real-Time Clock + +Required properties: +- compatible: Should contain "maxim,mcp795". +- reg: SPI address for chip + +Example: + mcp795: rtc@0 { + compatible = "maxim,mcp795"; + reg = <0>; + }; diff --git a/Documentation/devicetree/bindings/rtc/microchip,pic32-rtc.txt b/Documentation/devicetree/bindings/rtc/microchip,pic32-rtc.txt new file mode 100644 index 0000000..180b714 --- /dev/null +++ b/Documentation/devicetree/bindings/rtc/microchip,pic32-rtc.txt @@ -0,0 +1,21 @@ +* Microchip PIC32 Real Time Clock and Calendar + +The RTCC keeps time in hours, minutes, and seconds, and one half second. It +provides a calendar in weekday, date, month, and year. It also provides a +configurable alarm. + +Required properties: +- compatible: should be: "microchip,pic32mzda-rtc" +- reg: physical base address of the controller and length of memory mapped + region. +- interrupts: RTC alarm/event interrupt +- clocks: clock phandle + +Example: + + rtc: rtc@1f8c0000 { + compatible = "microchip,pic32mzda-rtc"; + reg = <0x1f8c0000 0x60>; + interrupts = <166 IRQ_TYPE_EDGE_RISING>; + clocks = <&PBCLK6>; + }; diff --git a/Documentation/devicetree/bindings/rtc/s3c-rtc.txt b/Documentation/devicetree/bindings/rtc/s3c-rtc.txt index 1068ffc..fdde63a 100644 --- a/Documentation/devicetree/bindings/rtc/s3c-rtc.txt +++ b/Documentation/devicetree/bindings/rtc/s3c-rtc.txt @@ -15,9 +15,10 @@ Required properties: is the rtc tick interrupt. The number of cells representing a interrupt depends on the parent interrupt controller. - clocks: Must contain a list of phandle and clock specifier for the rtc - and source clocks. -- clock-names: Must contain "rtc" and "rtc_src" entries sorted in the - same order as the clocks property. + clock and in the case of a s3c6410 compatible controller, also + a source clock. +- clock-names: Must contain "rtc" and for a s3c6410 compatible controller, + a "rtc_src" sorted in the same order as the clocks property. Example: diff --git a/Documentation/devicetree/bindings/scsi/hisilicon-sas.txt b/Documentation/devicetree/bindings/scsi/hisilicon-sas.txt index f67e761..bf2411f 100644 --- a/Documentation/devicetree/bindings/scsi/hisilicon-sas.txt +++ b/Documentation/devicetree/bindings/scsi/hisilicon-sas.txt @@ -5,6 +5,7 @@ The HiSilicon SAS controller supports SAS/SATA. Main node required properties: - compatible : value should be as follows: (a) "hisilicon,hip05-sas-v1" for v1 hw in hip05 chipset + (b) "hisilicon,hip06-sas-v2" for v2 hw in hip06 chipset - sas-addr : array of 8 bytes for host SAS address - reg : Address and length of the SAS register - hisilicon,sas-syscon: phandle of syscon used for sas control @@ -13,7 +14,7 @@ Main node required properties: - ctrl-clock-ena-reg : offset to controller clock enable register in ctrl reg - queue-count : number of delivery and completion queues in the controller - phy-count : number of phys accessible by the controller - - interrupts : Interrupts for phys, completion queues, and fatal + - interrupts : For v1 hw: Interrupts for phys, completion queues, and fatal sources; the interrupts are ordered in 3 groups, as follows: - Phy interrupts - Completion queue interrupts @@ -30,6 +31,24 @@ Main node required properties: Fatal interrupts : the fatal interrupts are ordered as follows: - ECC - AXI bus + For v2 hw: Interrupts for phys, Sata, and completion queues; + the interrupts are ordered in 3 groups, as follows: + - Phy interrupts + - Sata interrupts + - Completion queue interrupts + Phy interrupts : Each controller has 2 phy interrupts: + - phy up/down + - channel interrupt + Sata interrupts : Each phy on the controller has 1 Sata + interrupt. The interrupts are ordered in increasing + order. + Completion queue interrupts : each completion queue has 1 + interrupt source. The interrupts are ordered in + increasing order. + +Optional main node properties: + - hip06-sas-v2-quirk-amt : when set, indicates that the v2 controller has the + "am-max-transmissions" limitation. Example: sas0: sas@c1000000 { diff --git a/Documentation/devicetree/bindings/serial/brcm,bcm2835-aux-uart.txt b/Documentation/devicetree/bindings/serial/brcm,bcm2835-aux-uart.txt new file mode 100644 index 0000000..b5cc629 --- /dev/null +++ b/Documentation/devicetree/bindings/serial/brcm,bcm2835-aux-uart.txt @@ -0,0 +1,18 @@ +* BCM2835 AUXILIAR UART + +Required properties: + +- compatible: "brcm,bcm2835-aux-uart" +- reg: The base address of the UART register bank. +- interrupts: A single interrupt specifier. +- clocks: Clock driving the hardware; used to figure out the baud rate + divisor. + +Example: + + uart1: serial@7e215040 { + compatible = "brcm,bcm2835-aux-uart"; + reg = <0x7e215040 0x40>; + interrupts = <1 29>; + clocks = <&aux BCM2835_AUX_CLOCK_UART>; + }; diff --git a/Documentation/devicetree/bindings/serial/mtk-uart.txt b/Documentation/devicetree/bindings/serial/mtk-uart.txt index a833a01..e99e10a 100644 --- a/Documentation/devicetree/bindings/serial/mtk-uart.txt +++ b/Documentation/devicetree/bindings/serial/mtk-uart.txt @@ -7,6 +7,7 @@ Required properties: * "mediatek,mt6582-uart" for MT6582 compatible UARTS * "mediatek,mt6589-uart" for MT6589 compatible UARTS * "mediatek,mt6795-uart" for MT6795 compatible UARTS + * "mediatek,mt7623-uart" for MT7623 compatible UARTS * "mediatek,mt8127-uart" for MT8127 compatible UARTS * "mediatek,mt8135-uart" for MT8135 compatible UARTS * "mediatek,mt8173-uart" for MT8173 compatible UARTS diff --git a/Documentation/devicetree/bindings/serial/renesas,sci-serial.txt b/Documentation/devicetree/bindings/serial/renesas,sci-serial.txt index 401b1b3..528c3b9 100644 --- a/Documentation/devicetree/bindings/serial/renesas,sci-serial.txt +++ b/Documentation/devicetree/bindings/serial/renesas,sci-serial.txt @@ -19,6 +19,8 @@ Required properties: - "renesas,scifa-r8a7791" for R8A7791 (R-Car M2-W) SCIFA compatible UART. - "renesas,scifb-r8a7791" for R8A7791 (R-Car M2-W) SCIFB compatible UART. - "renesas,hscif-r8a7791" for R8A7791 (R-Car M2-W) HSCIF compatible UART. + - "renesas,scif-r8a7792" for R8A7792 (R-Car V2H) SCIF compatible UART. + - "renesas,hscif-r8a7792" for R8A7792 (R-Car V2H) HSCIF compatible UART. - "renesas,scif-r8a7793" for R8A7793 (R-Car M2-N) SCIF compatible UART. - "renesas,scifa-r8a7793" for R8A7793 (R-Car M2-N) SCIFA compatible UART. - "renesas,scifb-r8a7793" for R8A7793 (R-Car M2-N) SCIFB compatible UART. diff --git a/Documentation/devicetree/bindings/soc/fsl/rcpm.txt b/Documentation/devicetree/bindings/soc/fsl/rcpm.txt new file mode 100644 index 0000000..e284e4e --- /dev/null +++ b/Documentation/devicetree/bindings/soc/fsl/rcpm.txt @@ -0,0 +1,63 @@ +* Run Control and Power Management +------------------------------------------- +The RCPM performs all device-level tasks associated with device run control +and power management. + +Required properites: + - reg : Offset and length of the register set of the RCPM block. + - fsl,#rcpm-wakeup-cells : The number of IPPDEXPCR register cells in the + fsl,rcpm-wakeup property. + - compatible : Must contain a chip-specific RCPM block compatible string + and (if applicable) may contain a chassis-version RCPM compatible + string. Chip-specific strings are of the form "fsl,<chip>-rcpm", + such as: + * "fsl,p2041-rcpm" + * "fsl,p5020-rcpm" + * "fsl,t4240-rcpm" + + Chassis-version strings are of the form "fsl,qoriq-rcpm-<version>", + such as: + * "fsl,qoriq-rcpm-1.0": for chassis 1.0 rcpm + * "fsl,qoriq-rcpm-2.0": for chassis 2.0 rcpm + * "fsl,qoriq-rcpm-2.1": for chassis 2.1 rcpm + +All references to "1.0" and "2.0" refer to the QorIQ chassis version to +which the chip complies. +Chassis Version Example Chips +--------------- ------------------------------- +1.0 p4080, p5020, p5040, p2041, p3041 +2.0 t4240, b4860, b4420 +2.1 t1040, ls1021 + +Example: +The RCPM node for T4240: + rcpm: global-utilities@e2000 { + compatible = "fsl,t4240-rcpm", "fsl,qoriq-rcpm-2.0"; + reg = <0xe2000 0x1000>; + fsl,#rcpm-wakeup-cells = <2>; + }; + +* Freescale RCPM Wakeup Source Device Tree Bindings +------------------------------------------- +Required fsl,rcpm-wakeup property should be added to a device node if the device +can be used as a wakeup source. + + - fsl,rcpm-wakeup: Consists of a phandle to the rcpm node and the IPPDEXPCR + register cells. The number of IPPDEXPCR register cells is defined in + "fsl,#rcpm-wakeup-cells" in the rcpm node. The first register cell is + the bit mask that should be set in IPPDEXPCR0, and the second register + cell is for IPPDEXPCR1, and so on. + + Note: IPPDEXPCR(IP Powerdown Exception Control Register) provides a + mechanism for keeping certain blocks awake during STANDBY and MEM, in + order to use them as wake-up sources. + +Example: + lpuart0: serial@2950000 { + compatible = "fsl,ls1021a-lpuart"; + reg = <0x0 0x2950000 0x0 0x1000>; + interrupts = <GIC_SPI 80 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&sysclk>; + clock-names = "ipg"; + fsl,rcpm-wakeup = <&rcpm 0x0 0x40000000>; + }; diff --git a/Documentation/devicetree/bindings/soc/rockchip/power_domain.txt b/Documentation/devicetree/bindings/soc/rockchip/power_domain.txt index 112756e..13dc6a3 100644 --- a/Documentation/devicetree/bindings/soc/rockchip/power_domain.txt +++ b/Documentation/devicetree/bindings/soc/rockchip/power_domain.txt @@ -6,6 +6,7 @@ powered up/down by software based on different application scenes to save power. Required properties for power domain controller: - compatible: Should be one of the following. "rockchip,rk3288-power-controller" - for RK3288 SoCs. + "rockchip,rk3368-power-controller" - for RK3368 SoCs. - #power-domain-cells: Number of cells in a power-domain specifier. Should be 1 for multiple PM domains. - #address-cells: Should be 1. @@ -14,6 +15,7 @@ Required properties for power domain controller: Required properties for power domain sub nodes: - reg: index of the power domain, should use macros in: "include/dt-bindings/power/rk3288-power.h" - for RK3288 type power domain. + "include/dt-bindings/power/rk3368-power.h" - for RK3368 type power domain. - clocks (optional): phandles to clocks which need to be enabled while power domain switches state. @@ -31,11 +33,24 @@ Example: }; }; + power: power-controller { + compatible = "rockchip,rk3368-power-controller"; + #power-domain-cells = <1>; + #address-cells = <1>; + #size-cells = <0>; + + pd_gpu_1 { + reg = <RK3368_PD_GPU_1>; + clocks = <&cru ACLK_GPU_CFG>; + }; + }; + Node of a device using power domains must have a power-domains property, containing a phandle to the power device node and an index specifying which power domain to use. The index should use macros in: "include/dt-bindings/power/rk3288-power.h" - for rk3288 type power domain. + "include/dt-bindings/power/rk3368-power.h" - for rk3368 type power domain. Example of the node using power domain: @@ -44,3 +59,9 @@ Example of the node using power domain: power-domains = <&power RK3288_PD_GPU>; /* ... */ }; + + node { + /* ... */ + power-domains = <&power RK3368_PD_GPU_1>; + /* ... */ + }; diff --git a/Documentation/devicetree/bindings/sound/adi,adau17x1.txt b/Documentation/devicetree/bindings/sound/adi,adau17x1.txt new file mode 100644 index 0000000..8dbce0e --- /dev/null +++ b/Documentation/devicetree/bindings/sound/adi,adau17x1.txt @@ -0,0 +1,24 @@ +Analog Devices ADAU1361/ADAU1461/ADAU1761/ADAU1961/ADAU1381/ADAU1781 + +Required properties: + + - compatible: Should contain one of the following: + "adi,adau1361" + "adi,adau1461" + "adi,adau1761" + "adi,adau1961" + "adi,adau1381" + "adi,adau1781" + + - reg: The i2c address. Value depends on the state of ADDR0 + and ADDR1, as wired in hardware. + +Examples: +#include <dt-bindings/sound/adau17x1.h> + + i2c_bus { + adau1361@38 { + compatible = "adi,adau1761"; + reg = <0x38>; + }; + }; diff --git a/Documentation/devicetree/bindings/sound/cs4271.txt b/Documentation/devicetree/bindings/sound/cs4271.txt index e2cd1d7..6e699ce 100644 --- a/Documentation/devicetree/bindings/sound/cs4271.txt +++ b/Documentation/devicetree/bindings/sound/cs4271.txt @@ -33,12 +33,19 @@ Optional properties: Note that this is not needed in case the clocks are stable throughout the entire runtime of the codec. + - vd-supply: Digital power + - vl-supply: Logic power + - va-supply: Analog Power + Examples: codec_i2c: cs4271@10 { compatible = "cirrus,cs4271"; reg = <0x10>; reset-gpio = <&gpio 23 0>; + vd-supply = <&vdd_3v3_reg>; + vl-supply = <&vdd_3v3_reg>; + va-supply = <&vdd_3v3_reg>; }; codec_spi: cs4271@0 { diff --git a/Documentation/devicetree/bindings/sound/fsl-asoc-card.txt b/Documentation/devicetree/bindings/sound/fsl-asoc-card.txt index 4da41bf..ceaef51 100644 --- a/Documentation/devicetree/bindings/sound/fsl-asoc-card.txt +++ b/Documentation/devicetree/bindings/sound/fsl-asoc-card.txt @@ -24,6 +24,9 @@ The compatible list for this generic sound card currently: "fsl,imx-audio-cs42888" + "fsl,imx-audio-cs427x" + (compatible with CS4271 and CS4272) + "fsl,imx-audio-wm8962" (compatible with Documentation/devicetree/bindings/sound/imx-audio-wm8962.txt) @@ -63,6 +66,12 @@ Optional properties: - audio-asrc : The phandle of ASRC. It can be absent if there's no need to add ASRC support via DPCM. +Optional unless SSI is selected as a CPU DAI: + + - mux-int-port : The internal port of the i.MX audio muxer (AUDMUX) + + - mux-ext-port : The external port of the i.MX audio muxer + Example: sound-cs42888 { compatible = "fsl,imx-audio-cs42888"; diff --git a/Documentation/devicetree/bindings/sound/max9867.txt b/Documentation/devicetree/bindings/sound/max9867.txt new file mode 100644 index 0000000..394cd4e --- /dev/null +++ b/Documentation/devicetree/bindings/sound/max9867.txt @@ -0,0 +1,17 @@ +max9867 codec + +This device supports I2C mode only. + +Required properties: + +- compatible : "maxim,max9867" +- reg : The chip select number on the I2C bus + +Example: + +&i2c { + max9867: max9867@0x18 { + compatible = "maxim,max9867"; + reg = <0x18>; + }; +}; diff --git a/Documentation/devicetree/bindings/sound/max98926.txt b/Documentation/devicetree/bindings/sound/max98926.txt new file mode 100644 index 0000000..0b7f4e4 --- /dev/null +++ b/Documentation/devicetree/bindings/sound/max98926.txt @@ -0,0 +1,32 @@ +max98926 audio CODEC + +This device supports I2C. + +Required properties: + + - compatible : "maxim,max98926" + + - vmon-slot-no : slot number used to send voltage information + or in inteleave mode this will be used as + interleave slot. + + - imon-slot-no : slot number used to send current information + + - interleave-mode : When using two MAX98926 in a system it is + possible to create ADC data that that will + overflow the frame size. Digital Audio Interleave + mode provides a means to output VMON and IMON data + from two devices on a single DOUT line when running + smaller frames sizes such as 32 BCLKS per LRCLK or + 48 BCLKS per LRCLK. + + - reg : the I2C address of the device for I2C + +Example: + +codec: max98926@1a { + compatible = "maxim,max98926"; + vmon-slot-no = <0>; + imon-slot-no = <2>; + reg = <0x1a>; +}; diff --git a/Documentation/devicetree/bindings/sound/mt8173-rt5650-rt5514.txt b/Documentation/devicetree/bindings/sound/mt8173-rt5650-rt5514.txt new file mode 100644 index 0000000..e8b3c80 --- /dev/null +++ b/Documentation/devicetree/bindings/sound/mt8173-rt5650-rt5514.txt @@ -0,0 +1,15 @@ +MT8173 with RT5650 RT5514 CODECS + +Required properties: +- compatible : "mediatek,mt8173-rt5650-rt5514" +- mediatek,audio-codec: the phandles of rt5650 and rt5514 codecs +- mediatek,platform: the phandle of MT8173 ASoC platform + +Example: + + sound { + compatible = "mediatek,mt8173-rt5650-rt5514"; + mediatek,audio-codec = <&rt5650 &rt5514>; + mediatek,platform = <&afe>; + }; + diff --git a/Documentation/devicetree/bindings/sound/mt8173-rt5650.txt b/Documentation/devicetree/bindings/sound/mt8173-rt5650.txt new file mode 100644 index 0000000..fe5a5ef --- /dev/null +++ b/Documentation/devicetree/bindings/sound/mt8173-rt5650.txt @@ -0,0 +1,15 @@ +MT8173 with RT5650 CODECS + +Required properties: +- compatible : "mediatek,mt8173-rt5650" +- mediatek,audio-codec: the phandles of rt5650 codecs +- mediatek,platform: the phandle of MT8173 ASoC platform + +Example: + + sound { + compatible = "mediatek,mt8173-rt5650"; + mediatek,audio-codec = <&rt5650>; + mediatek,platform = <&afe>; + }; + diff --git a/Documentation/devicetree/bindings/sound/pcm179x.txt b/Documentation/devicetree/bindings/sound/pcm179x.txt index 4ae70d3..436c2b2 100644 --- a/Documentation/devicetree/bindings/sound/pcm179x.txt +++ b/Documentation/devicetree/bindings/sound/pcm179x.txt @@ -1,6 +1,6 @@ Texas Instruments pcm179x DT bindings -This driver supports the SPI bus. +This driver supports both the I2C and SPI bus. Required properties: @@ -9,6 +9,11 @@ Required properties: For required properties on SPI, please consult Documentation/devicetree/bindings/spi/spi-bus.txt +Required properties on I2C: + + - reg: the I2C address + + Examples: codec_spi: 1792a@0 { @@ -16,3 +21,7 @@ Examples: spi-max-frequency = <600000>; }; + codec_i2c: 1792a@4c { + compatible = "ti,pcm1792a"; + reg = <0x4c>; + }; diff --git a/Documentation/devicetree/bindings/sound/renesas,rsnd.txt b/Documentation/devicetree/bindings/sound/renesas,rsnd.txt index 8ee0fa9..c7b29df 100644 --- a/Documentation/devicetree/bindings/sound/renesas,rsnd.txt +++ b/Documentation/devicetree/bindings/sound/renesas,rsnd.txt @@ -1,6 +1,337 @@ Renesas R-Car sound +============================================= +* Modules +============================================= + +Renesas R-Car sound is constructed from below modules +(for Gen2 or later) + + SCU : Sampling Rate Converter Unit + - SRC : Sampling Rate Converter + - CMD + - CTU : Channel Transfer Unit + - MIX : Mixer + - DVC : Digital Volume and Mute Function + SSIU : Serial Sound Interface Unit + SSI : Serial Sound Interface + +See detail of each module's channels, connection, limitation on datasheet + +============================================= +* Multi channel +============================================= + +Multi channel is supported by Multi-SSI, or TDM-SSI. + + Multi-SSI : 6ch case, you can use stereo x 3 SSI + TDM-SSI : 6ch case, you can use TDM + +============================================= +* Enable/Disable each modules +============================================= + +See datasheet to check SRC/CTU/MIX/DVC connect-limitation. +DT controls enabling/disabling module. +${LINUX}/arch/arm/boot/dts/r8a7790-lager.dts can be good example. +This is example of + +Playback: [MEM] -> [SRC2] -> [DVC0] -> [SSIU0/SSI0] -> [codec] +Capture: [MEM] <- [DVC1] <- [SRC3] <- [SSIU1/SSI1] <- [codec] + + &rcar_sound { + ... + rcar_sound,dai { + dai0 { + playback = <&ssi0 &src2 &dvc0>; + capture = <&ssi1 &src3 &dvc1>; + }; + }; + }; + +You can use below. +${LINUX}/arch/arm/boot/dts/r8a7790.dts can be good example. + + &src0 &ctu00 &mix0 &dvc0 &ssi0 + &src1 &ctu01 &mix1 &dvc1 &ssi1 + &src2 &ctu02 &ssi2 + &src3 &ctu03 &ssi3 + &src4 &ssi4 + &src5 &ctu10 &ssi5 + &src6 &ctu11 &ssi6 + &src7 &ctu12 &ssi7 + &src8 &ctu13 &ssi8 + &src9 &ssi9 + +============================================= +* SRC (Sampling Rate Converter) +============================================= + + [xx]Hz [yy]Hz + ------> [SRC] ------> + +SRC can convert [xx]Hz to [yy]Hz. Then, it has below 2 modes + + Asynchronous mode: input data / output data are based on different clocks. + you can use this mode on Playback / Capture + Synchronous mode: input data / output data are based on same clocks. + This mode will be used if system doesn't have its input clock, + for example digital TV case. + you can use this mode on Playback + +------------------ +** Asynchronous mode +------------------ + +You need to use "renesas,rsrc-card" sound card for it. +example) + + sound { + compatible = "renesas,rsrc-card"; + ... + /* + * SRC Asynchronous mode setting + * Playback: + * All input data will be converted to 48kHz + * Capture: + * Inputed 48kHz data will be converted to + * system specified Hz + */ + convert-rate = <48000>; + ... + cpu { + sound-dai = <&rcar_sound>; + }; + codec { + ... + }; + }; + +------------------ +** Synchronous mode +------------------ + + > amixer set "SRC Out Rate" on + > aplay xxxx.wav + > amixer set "SRC Out Rate" 48000 + > amixer set "SRC Out Rate" 44100 + +============================================= +* CTU (Channel Transfer Unit) +============================================= + + [xx]ch [yy]ch + ------> [CTU] --------> + +CTU can convert [xx]ch to [yy]ch, or exchange outputed channel. +CTU conversion needs matrix settings. +For more detail information, see below + + Renesas R-Car datasheet + - Sampling Rate Converter Unit (SCU) + - SCU Operation + - CMD Block + - Functional Blocks in CMD + + Renesas R-Car datasheet + - Sampling Rate Converter Unit (SCU) + - Register Description + - CTUn Scale Value exx Register (CTUn_SVxxR) + + ${LINUX}/sound/soc/sh/rcar/ctu.c + - comment of header + +You need to use "renesas,rsrc-card" sound card for it. +example) + + sound { + compatible = "renesas,rsrc-card"; + ... + /* + * CTU setting + * All input data will be converted to 2ch + * as output data + */ + convert-channels = <2>; + ... + cpu { + sound-dai = <&rcar_sound>; + }; + codec { + ... + }; + }; + +Ex) Exchange output channel + Input -> Output + 1ch -> 0ch + 0ch -> 1ch + + example of using matrix + output 0ch = (input 0ch x 0) + (input 1ch x 1) + output 1ch = (input 0ch x 1) + (input 1ch x 0) + + amixer set "CTU Reset" on + amixer set "CTU Pass" 9,10 + amixer set "CTU SV0" 0,4194304 + amixer set "CTU SV1" 4194304,0 + + example of changing connection + amixer set "CTU Reset" on + amixer set "CTU Pass" 2,1 + +============================================= +* MIX (Mixer) +============================================= + +MIX merges 2 sounds path. You can see 2 sound interface on system, +and these sounds will be merged by MIX. + + aplay -D plughw:0,0 xxxx.wav & + aplay -D plughw:0,1 yyyy.wav + +You need to use "renesas,rsrc-card" sound card for it. +Ex) + [MEM] -> [SRC1] -> [CTU02] -+-> [MIX0] -> [DVC0] -> [SSI0] + | + [MEM] -> [SRC2] -> [CTU03] -+ + + sound { + compatible = "renesas,rsrc-card"; + ... + cpu@0 { + sound-dai = <&rcar_sound 0>; + }; + cpu@1 { + sound-dai = <&rcar_sound 1>; + }; + codec { + ... + }; + }; + + &rcar_sound { + ... + rcar_sound,dai { + dai0 { + playback = <&src1 &ctu02 &mix0 &dvc0 &ssi0>; + }; + dai1 { + playback = <&src2 &ctu03 &mix0 &dvc0 &ssi0>; + }; + }; + }; + +============================================= +* DVC (Digital Volume and Mute Function) +============================================= + +DVC controls Playback/Capture volume. + +Playback Volume + amixer set "DVC Out" 100% + +Capture Volume + amixer set "DVC In" 100% + +Playback Mute + amixer set "DVC Out Mute" on + +Capture Mute + amixer set "DVC In Mute" on + +Volume Ramp + amixer set "DVC Out Ramp Up Rate" "0.125 dB/64 steps" + amixer set "DVC Out Ramp Down Rate" "0.125 dB/512 steps" + amixer set "DVC Out Ramp" on + aplay xxx.wav & + amixer set "DVC Out" 80% // Volume Down + amixer set "DVC Out" 100% // Volume Up + +============================================= +* SSIU (Serial Sound Interface Unit) +============================================= + +There is no DT settings for SSIU, because SSIU will be automatically +selected via SSI. +SSIU can avoid some under/over run error, because it has some buffer. +But you can't use it if SSI was PIO mode. +In DMA mode, you can select not to use SSIU by using "no-busif" on DT. + + &ssi0 { + no-busif; + }; + +============================================= +* SSI (Serial Sound Interface) +============================================= + +** PIO mode + +You can use PIO mode which is for connection check by using. +Note: The system will drop non-SSI modules in PIO mode +even though if DT is selecting other modules. + + &ssi0 { + pio-transfer + }; + +** DMA mode without SSIU + +You can use DMA without SSIU. +Note: under/over run, or noise are likely to occur + + &ssi0 { + no-busif; + }; + +** PIN sharing + +Each SSI can share WS pin. It is based on platform. +This is example if SSI1 want to share WS pin with SSI0 + + &ssi1 { + shared-pin; + }; + +** Multi-SSI + +You can use Multi-SSI. +This is example of SSI0/SSI1/SSI2 (= for 6ch) + + &rcar_sound { + ... + rcar_sound,dai { + dai0 { + playback = <&ssi0 &ssi1 &ssi2 &src0 &dvc0>; + }; + }; + }; + +** TDM-SSI + +You can use TDM with SSI. +This is example of TDM 6ch. +Driver can automatically switches TDM <-> stereo mode in this case. + + rsnd_tdm: sound { + compatible = "simple-audio-card"; + ... + simple-audio-card,cpu { + /* system can use TDM 6ch */ + dai-tdm-slot-num = <6>; + sound-dai = <&rcar_sound>; + }; + simple-audio-card,codec { + ... + }; + }; + + +============================================= Required properties: +============================================= + - compatible : "renesas,rcar_sound-<soctype>", fallbacks "renesas,rcar_sound-gen1" if generation1, and "renesas,rcar_sound-gen2" if generation2 @@ -64,7 +395,10 @@ DAI subnode properties: - playback : list of playback modules - capture : list of capture modules + +============================================= Example: +============================================= rcar_sound: sound@ec500000 { #sound-dai-cells = <1>; @@ -250,7 +584,9 @@ rcar_sound: sound@ec500000 { }; }; +============================================= Example: simple sound card +============================================= rsnd_ak4643: sound { compatible = "simple-audio-card"; @@ -290,7 +626,9 @@ Example: simple sound card shared-pin; }; +============================================= Example: simple sound card for TDM +============================================= rsnd_tdm: sound { compatible = "simple-audio-card"; @@ -309,7 +647,9 @@ Example: simple sound card for TDM }; }; +============================================= Example: simple sound card for Multi channel +============================================= &rcar_sound { pinctrl-0 = <&sound_pins &sound_clk_pins>; diff --git a/Documentation/devicetree/bindings/sound/renesas,rsrc-card.txt b/Documentation/devicetree/bindings/sound/renesas,rsrc-card.txt index 2b2caa2..255ece3 100644 --- a/Documentation/devicetree/bindings/sound/renesas,rsrc-card.txt +++ b/Documentation/devicetree/bindings/sound/renesas,rsrc-card.txt @@ -30,6 +30,7 @@ Optional subnode properties: - frame-inversion : bool property. Add this if the dai-link uses frame clock inversion. - convert-rate : platform specified sampling rate convert +- convert-channels : platform specified converted channel size (2 - 8 ch) - audio-prefix : see audio-routing - audio-routing : A list of the connections between audio components. Each entry is a pair of strings, the first being the connection's sink, diff --git a/Documentation/devicetree/bindings/sound/rockchip-i2s.txt b/Documentation/devicetree/bindings/sound/rockchip-i2s.txt index b7f3a93..6e86d8a 100644 --- a/Documentation/devicetree/bindings/sound/rockchip-i2s.txt +++ b/Documentation/devicetree/bindings/sound/rockchip-i2s.txt @@ -9,6 +9,7 @@ Required properties: - "rockchip,rk3066-i2s": for rk3066 - "rockchip,rk3188-i2s", "rockchip,rk3066-i2s": for rk3188 - "rockchip,rk3288-i2s", "rockchip,rk3066-i2s": for rk3288 + - "rockchip,rk3399-i2s", "rockchip,rk3066-i2s": for rk3399 - reg: physical base address of the controller and length of memory mapped region. - interrupts: should contain the I2S interrupt. diff --git a/Documentation/devicetree/bindings/sound/rockchip-spdif.txt b/Documentation/devicetree/bindings/sound/rockchip-spdif.txt index e64dbde..1104642 100644 --- a/Documentation/devicetree/bindings/sound/rockchip-spdif.txt +++ b/Documentation/devicetree/bindings/sound/rockchip-spdif.txt @@ -7,8 +7,12 @@ a fibre cable. Required properties: - compatible: should be one of the following: - - "rockchip,rk3288-spdif", "rockchip,rk3188-spdif" or - "rockchip,rk3066-spdif" + - "rockchip,rk3066-spdif" + - "rockchip,rk3188-spdif" + - "rockchip,rk3288-spdif" + - "rockchip,rk3366-spdif" + - "rockchip,rk3368-spdif" + - "rockchip,rk3399-spdif" - reg: physical base address of the controller and length of memory mapped region. - interrupts: should contain the SPDIF interrupt. diff --git a/Documentation/devicetree/bindings/sound/rt5514.txt b/Documentation/devicetree/bindings/sound/rt5514.txt new file mode 100644 index 0000000..e24436f --- /dev/null +++ b/Documentation/devicetree/bindings/sound/rt5514.txt @@ -0,0 +1,25 @@ +RT5514 audio CODEC + +This device supports I2C only. + +Required properties: + +- compatible : "realtek,rt5514". + +- reg : The I2C address of the device. + +Pins on the device (for linking into audio routes) for RT5514: + + * DMIC1L + * DMIC1R + * DMIC2L + * DMIC2R + * AMICL + * AMICR + +Example: + +codec: rt5514@57 { + compatible = "realtek,rt5514"; + reg = <0x57>; +}; diff --git a/Documentation/devicetree/bindings/sound/rt5616.txt b/Documentation/devicetree/bindings/sound/rt5616.txt index efc48c6..e410858 100644 --- a/Documentation/devicetree/bindings/sound/rt5616.txt +++ b/Documentation/devicetree/bindings/sound/rt5616.txt @@ -8,6 +8,12 @@ Required properties: - reg : The I2C address of the device. +Optional properties: + +- clocks: The phandle of the master clock to the CODEC. + +- clock-names: Should be "mclk". + Pins on the device (for linking into audio routes) for RT5616: * IN1P diff --git a/Documentation/devicetree/bindings/sound/rt5640.txt b/Documentation/devicetree/bindings/sound/rt5640.txt index 9e62f6e..57fe646 100644 --- a/Documentation/devicetree/bindings/sound/rt5640.txt +++ b/Documentation/devicetree/bindings/sound/rt5640.txt @@ -12,6 +12,9 @@ Required properties: Optional properties: +- clocks: The phandle of the master clock to the CODEC +- clock-names: Should be "mclk" + - realtek,in1-differential - realtek,in2-differential - realtek,in3-differential diff --git a/Documentation/devicetree/bindings/sound/sunxi,sun4i-spdif.txt b/Documentation/devicetree/bindings/sound/sunxi,sun4i-spdif.txt new file mode 100644 index 0000000..13503aa --- /dev/null +++ b/Documentation/devicetree/bindings/sound/sunxi,sun4i-spdif.txt @@ -0,0 +1,39 @@ +Allwinner Sony/Philips Digital Interface Format (S/PDIF) Controller + +The Allwinner S/PDIF audio block is a transceiver that allows the +processor to receive and transmit digital audio via an coaxial cable or +a fibre cable. +For now only playback is supported. + +Required properties: + + - compatible : should be one of the following: + - "allwinner,sun4i-a10-spdif": for the Allwinner A10 SoC + + - reg : Offset and length of the register set for the device. + + - interrupts : Contains the spdif interrupt. + + - dmas : Generic dma devicetree binding as described in + Documentation/devicetree/bindings/dma/dma.txt. + + - dma-names : Two dmas have to be defined, "tx" and "rx". + + - clocks : Contains an entry for each entry in clock-names. + + - clock-names : Includes the following entries: + "apb" clock for the spdif bus. + "spdif" clock for spdif controller. + +Example: + +spdif: spdif@01c21000 { + compatible = "allwinner,sun4i-a10-spdif"; + reg = <0x01c21000 0x40>; + interrupts = <13>; + clocks = <&apb0_gates 1>, <&spdif_clk>; + clock-names = "apb", "spdif"; + dmas = <&dma 0 2>, <&dma 0 2>; + dma-names = "rx", "tx"; + status = "okay"; +}; diff --git a/Documentation/devicetree/bindings/sound/ti,ads117x.txt b/Documentation/devicetree/bindings/sound/ti,ads117x.txt new file mode 100644 index 0000000..7db19b5 --- /dev/null +++ b/Documentation/devicetree/bindings/sound/ti,ads117x.txt @@ -0,0 +1,11 @@ +Texas Intstruments ADS117x ADC + +Required properties: + + - compatible : "ti,ads1174" or "ti,ads1178" + +Example: + +ads1178 { + compatible = "ti,ads1178"; +}; diff --git a/Documentation/devicetree/bindings/sparc_sun_oracle_rng.txt b/Documentation/devicetree/bindings/sparc_sun_oracle_rng.txt new file mode 100644 index 0000000..b0b2111 --- /dev/null +++ b/Documentation/devicetree/bindings/sparc_sun_oracle_rng.txt @@ -0,0 +1,30 @@ +HWRNG support for the n2_rng driver + +Required properties: +- reg : base address to sample from +- compatible : should contain one of the following + RNG versions: + - 'SUNW,n2-rng' for Niagara 2 Platform (SUN UltraSPARC T2 CPU) + - 'SUNW,vf-rng' for Victoria Falls Platform (SUN UltraSPARC T2 Plus CPU) + - 'SUNW,kt-rng' for Rainbow/Yosemite Falls Platform (SUN SPARC T3/T4), (UltraSPARC KT/Niagara 3 - development names) + more recent systems (after Oracle acquisition of SUN) + - 'ORCL,m4-rng' for SPARC T5/M5 + - 'ORCL,m7-rng' for SPARC T7/M7 + +Examples: +/* linux LDOM on SPARC T5-2 */ +Node 0xf029a4f4 + .node: f029a4f4 + rng-#units: 00000002 + compatible: 'ORCL,m4-rng' + reg: 0000000e + name: 'random-number-generator' + +/* solaris on SPARC M7-8 */ +Node 0xf028c08c + rng-#units: 00000003 + compatible: 'ORCL,m7-rng' + reg: 0000000e + name: 'random-number-generator' + +PS: see as well prtconfs.git by DaveM diff --git a/Documentation/devicetree/bindings/spi/microchip,spi-pic32.txt b/Documentation/devicetree/bindings/spi/microchip,spi-pic32.txt new file mode 100644 index 0000000..79de379f --- /dev/null +++ b/Documentation/devicetree/bindings/spi/microchip,spi-pic32.txt @@ -0,0 +1,34 @@ +Microchip PIC32 SPI Master controller + +Required properties: +- compatible: Should be "microchip,pic32mzda-spi". +- reg: Address and length of register space for the device. +- interrupts: Should contain all three spi interrupts in sequence + of <fault-irq>, <receive-irq>, <transmit-irq>. +- interrupt-names: Should be "fault", "rx", "tx" in order. +- clocks: Phandle of the clock generating SPI clock on the bus. +- clock-names: Should be "mck0". +- cs-gpios: Specifies the gpio pins to be used for chipselects. + See: Documentation/devicetree/bindings/spi/spi-bus.txt + +Optional properties: +- dmas: Two or more DMA channel specifiers following the convention outlined + in Documentation/devicetree/bindings/dma/dma.txt +- dma-names: Names for the dma channels. There must be at least one channel + named "spi-tx" for transmit and named "spi-rx" for receive. + +Example: + +spi1: spi@1f821000 { + compatible = "microchip,pic32mzda-spi"; + reg = <0x1f821000 0x200>; + interrupts = <109 IRQ_TYPE_LEVEL_HIGH>, + <110 IRQ_TYPE_LEVEL_HIGH>, + <111 IRQ_TYPE_LEVEL_HIGH>; + interrupt-names = "fault", "rx", "tx"; + clocks = <&PBCLK2>; + clock-names = "mck0"; + cs-gpios = <&gpio3 4 GPIO_ACTIVE_LOW>; + dmas = <&dma 134>, <&dma 135>; + dma-names = "spi-rx", "spi-tx"; +}; diff --git a/Documentation/devicetree/bindings/spi/spi-bus.txt b/Documentation/devicetree/bindings/spi/spi-bus.txt index bbaa857..42d5954 100644 --- a/Documentation/devicetree/bindings/spi/spi-bus.txt +++ b/Documentation/devicetree/bindings/spi/spi-bus.txt @@ -61,6 +61,8 @@ contain the following properties. used for MOSI. Defaults to 1 if not present. - spi-rx-bus-width - (optional) The bus width(number of data wires) that used for MISO. Defaults to 1 if not present. +- spi-rx-delay-us - (optional) Microsecond delay after a read transfer. +- spi-tx-delay-us - (optional) Microsecond delay after a write transfer. Some SPI controllers and devices support Dual and Quad SPI transfer mode. It allows data in the SPI system to be transferred in 2 wires(DUAL) or 4 wires(QUAD). diff --git a/Documentation/devicetree/bindings/spi/spi-fsl-dspi.txt b/Documentation/devicetree/bindings/spi/spi-fsl-dspi.txt index fa77f87..d2969d2 100644 --- a/Documentation/devicetree/bindings/spi/spi-fsl-dspi.txt +++ b/Documentation/devicetree/bindings/spi/spi-fsl-dspi.txt @@ -13,8 +13,7 @@ Required properties: Optional property: - big-endian: If present the dspi device's registers are implemented - in big endian mode, otherwise in native mode(same with CPU), for more - detail please see: Documentation/devicetree/bindings/regmap/regmap.txt. + in big endian mode. Optional SPI slave node properties: - fsl,spi-cs-sck-delay: a delay in nanoseconds between activating chip diff --git a/Documentation/devicetree/bindings/spi/sqi-pic32.txt b/Documentation/devicetree/bindings/spi/sqi-pic32.txt new file mode 100644 index 0000000..c82d021 --- /dev/null +++ b/Documentation/devicetree/bindings/spi/sqi-pic32.txt @@ -0,0 +1,18 @@ +Microchip PIC32 Quad SPI controller +----------------------------------- +Required properties: +- compatible: Should be "microchip,pic32mzda-sqi". +- reg: Address and length of SQI controller register space. +- interrupts: Should contain SQI interrupt. +- clocks: Should contain phandle of two clocks in sequence, one that drives + clock on SPI bus and other that drives SQI controller. +- clock-names: Should be "spi_ck" and "reg_ck" in order. + +Example: + sqi1: spi@1f8e2000 { + compatible = "microchip,pic32mzda-sqi"; + reg = <0x1f8e2000 0x200>; + clocks = <&rootclk REF2CLK>, <&rootclk PB5CLK>; + clock-names = "spi_ck", "reg_ck"; + interrupts = <169 IRQ_TYPE_LEVEL_HIGH>; + }; diff --git a/Documentation/devicetree/bindings/sram/sram.txt b/Documentation/devicetree/bindings/sram/sram.txt index 42ee943..227e3a3 100644 --- a/Documentation/devicetree/bindings/sram/sram.txt +++ b/Documentation/devicetree/bindings/sram/sram.txt @@ -25,6 +25,11 @@ Required properties in the sram node: - ranges : standard definition, should translate from local addresses within the sram to bus addresses +Optional properties in the sram node: + +- no-memory-wc : the flag indicating, that SRAM memory region has not to + be remapped as write combining. WC is used by default. + Required properties in the area nodes: - reg : iomem address range, relative to the SRAM range diff --git a/Documentation/devicetree/bindings/thermal/exynos-thermal.txt b/Documentation/devicetree/bindings/thermal/exynos-thermal.txt index 695150a..70b4c16 100644 --- a/Documentation/devicetree/bindings/thermal/exynos-thermal.txt +++ b/Documentation/devicetree/bindings/thermal/exynos-thermal.txt @@ -11,6 +11,7 @@ "samsung,exynos5420-tmu" for TMU channel 0, 1 on Exynos5420 "samsung,exynos5420-tmu-ext-triminfo" for TMU channels 2, 3 and 4 Exynos5420 (Must pass triminfo base and triminfo clock) + "samsung,exynos5433-tmu" "samsung,exynos5440-tmu" "samsung,exynos7-tmu" - interrupt-parent : The phandle for the interrupt controller @@ -40,9 +41,14 @@ for current TMU channel -- "tmu_sclk" clock for functional operation of the current TMU channel -- vtmu-supply: This entry is optional and provides the regulator node supplying - voltage to TMU. If needed this entry can be placed inside - board/platform specific dts file. + +The Exynos TMU supports generating interrupts when reaching given +temperature thresholds. Number of supported thermal trip points depends +on the SoC (only first trip points defined in DT will be configured): + - most of SoC: 4 + - samsung,exynos5433-tmu: 8 + - samsung,exynos7-tmu: 8 + Following properties are mandatory (depending on SoC): - samsung,tmu_gain: Gain value for internal TMU operation. - samsung,tmu_reference_voltage: Value of TMU IP block's reference voltage @@ -56,6 +62,12 @@ Following properties are mandatory (depending on SoC): - samsung,tmu_default_temp_offset: Default temperature offset - samsung,tmu_cal_type: Callibration type +** Optional properties: + +- vtmu-supply: This entry is optional and provides the regulator node supplying + voltage to TMU. If needed this entry can be placed inside + board/platform specific dts file. + Example 1): tmu@100C0000 { diff --git a/Documentation/devicetree/bindings/thermal/mediatek-thermal.txt b/Documentation/devicetree/bindings/thermal/mediatek-thermal.txt new file mode 100644 index 0000000..81f9a51 --- /dev/null +++ b/Documentation/devicetree/bindings/thermal/mediatek-thermal.txt @@ -0,0 +1,43 @@ +* Mediatek Thermal + +This describes the device tree binding for the Mediatek thermal controller +which measures the on-SoC temperatures. This device does not have its own ADC, +instead it directly controls the AUXADC via AHB bus accesses. For this reason +this device needs phandles to the AUXADC. Also it controls a mux in the +apmixedsys register space via AHB bus accesses, so a phandle to the APMIXEDSYS +is also needed. + +Required properties: +- compatible: "mediatek,mt8173-thermal" +- reg: Address range of the thermal controller +- interrupts: IRQ for the thermal controller +- clocks, clock-names: Clocks needed for the thermal controller. required + clocks are: + "therm": Main clock needed for register access + "auxadc": The AUXADC clock +- resets: Reference to the reset controller controlling the thermal controller. +- mediatek,auxadc: A phandle to the AUXADC which the thermal controller uses +- mediatek,apmixedsys: A phandle to the APMIXEDSYS controller. +- #thermal-sensor-cells : Should be 0. See ./thermal.txt for a description. + +Optional properties: +- nvmem-cells: A phandle to the calibration data provided by a nvmem device. If + unspecified default values shall be used. +- nvmem-cell-names: Should be "calibration-data" + +Example: + + thermal: thermal@1100b000 { + #thermal-sensor-cells = <1>; + compatible = "mediatek,mt8173-thermal"; + reg = <0 0x1100b000 0 0x1000>; + interrupts = <0 70 IRQ_TYPE_LEVEL_LOW>; + clocks = <&pericfg CLK_PERI_THERM>, <&pericfg CLK_PERI_AUXADC>; + clock-names = "therm", "auxadc"; + resets = <&pericfg MT8173_PERI_THERM_SW_RST>; + reset-names = "therm"; + mediatek,auxadc = <&auxadc>; + mediatek,apmixedsys = <&apmixedsys>; + nvmem-cells = <&thermal_calibration_data>; + nvmem-cell-names = "calibration-data"; + }; diff --git a/Documentation/devicetree/bindings/timer/mediatek,mtk-timer.txt b/Documentation/devicetree/bindings/timer/mediatek,mtk-timer.txt index 8ff54eb..b1fe7e9 100644 --- a/Documentation/devicetree/bindings/timer/mediatek,mtk-timer.txt +++ b/Documentation/devicetree/bindings/timer/mediatek,mtk-timer.txt @@ -6,6 +6,7 @@ Required properties: * "mediatek,mt2701-timer" for MT2701 compatible timers * "mediatek,mt6580-timer" for MT6580 compatible timers * "mediatek,mt6589-timer" for MT6589 compatible timers + * "mediatek,mt7623-timer" for MT7623 compatible timers * "mediatek,mt8127-timer" for MT8127 compatible timers * "mediatek,mt8135-timer" for MT8135 compatible timers * "mediatek,mt8173-timer" for MT8173 compatible timers diff --git a/Documentation/devicetree/bindings/tty/serial/mvebu-uart.txt b/Documentation/devicetree/bindings/tty/serial/mvebu-uart.txt new file mode 100644 index 0000000..6087def --- /dev/null +++ b/Documentation/devicetree/bindings/tty/serial/mvebu-uart.txt @@ -0,0 +1,13 @@ +* Marvell UART : Non standard UART used in some of Marvell EBU SoCs (e.g., Armada-3700) + +Required properties: +- compatible: "marvell,armada-3700-uart" +- reg: offset and length of the register set for the device. +- interrupts: device interrupt + +Example: + serial@12000 { + compatible = "marvell,armada-3700-uart"; + reg = <0x12000 0x400>; + interrupts = <43>; + }; diff --git a/Documentation/devicetree/bindings/ufs/ufshcd-pltfrm.txt b/Documentation/devicetree/bindings/ufs/ufshcd-pltfrm.txt index 03c0e98..66f6adf 100644 --- a/Documentation/devicetree/bindings/ufs/ufshcd-pltfrm.txt +++ b/Documentation/devicetree/bindings/ufs/ufshcd-pltfrm.txt @@ -38,6 +38,9 @@ Optional properties: defined or a value in the array is "0" then it is assumed that the frequency is set by the parent clock or a fixed rate clock source. +-lanes-per-direction : number of lanes available per direction - either 1 or 2. + Note that it is assume same number of lanes is used both + directions at once. If not specified, default is 2 lanes per direction. Note: If above properties are not defined it can be assumed that the supply regulators or clocks are always on. diff --git a/Documentation/devicetree/bindings/usb/ci-hdrc-usb2.txt b/Documentation/devicetree/bindings/usb/ci-hdrc-usb2.txt index 781296b..1084e2b 100644 --- a/Documentation/devicetree/bindings/usb/ci-hdrc-usb2.txt +++ b/Documentation/devicetree/bindings/usb/ci-hdrc-usb2.txt @@ -2,7 +2,14 @@ Required properties: - compatible: should be one of: + "fsl,imx23-usb" "fsl,imx27-usb" + "fsl,imx28-usb" + "fsl,imx6q-usb" + "fsl,imx6sl-usb" + "fsl,imx6sx-usb" + "fsl,imx6ul-usb" + "fsl,imx7d-usb" "lsi,zevio-usb" "qcom,ci-hdrc" "chipidea,usb2" @@ -53,6 +60,22 @@ Optional properties: be specified. - phy-clkgate-delay-us: the delay time (us) between putting the PHY into low power mode and gating the PHY clock. +- non-zero-ttctrl-ttha: after setting this property, the value of register + ttctrl.ttha will be 0x7f; if not, the value will be 0x0, this is the default + value. It needs to be very carefully for setting this property, it is + recommended that consult with your IC engineer before setting this value. + On the most of chipidea platforms, the "usage_tt" flag at RTL is 0, so this + property only affects siTD. + If this property is not set, the max packet size is 1023 bytes, and if + the total of packet size for pervious transactions are more than 256 bytes, + it can't accept any transactions within this frame. The use case is single + transaction, but higher frame rate. + If this property is set, the max packet size is 188 bytes, it can handle + more transactions than above case, it can accept transactions until it + considers the left room size within frame is less than 188 bytes, software + needs to make sure it does not send more than 90% + maximum_periodic_data_per_frame. The use case is multiple transactions, but + less frame rate. i.mx specific properties - fsl,usbmisc: phandler of non-core register device, with one diff --git a/Documentation/devicetree/bindings/usb/dwc2.txt b/Documentation/devicetree/bindings/usb/dwc2.txt index 2213682..20a68bf 100644 --- a/Documentation/devicetree/bindings/usb/dwc2.txt +++ b/Documentation/devicetree/bindings/usb/dwc2.txt @@ -8,6 +8,8 @@ Required properties: - rockchip,rk3066-usb: The DWC2 USB controller instance in the rk3066 Soc; - "rockchip,rk3188-usb", "rockchip,rk3066-usb", "snps,dwc2": for rk3188 Soc; - "rockchip,rk3288-usb", "rockchip,rk3066-usb", "snps,dwc2": for rk3288 Soc; + - "lantiq,arx100-usb": The DWC2 USB controller instance in Lantiq ARX SoCs; + - "lantiq,xrx200-usb": The DWC2 USB controller instance in Lantiq XRX SoCs; - snps,dwc2: A generic DWC2 USB controller with default parameters. - reg : Should contain 1 register range (address and length) - interrupts : Should contain 1 interrupt diff --git a/Documentation/devicetree/bindings/usb/usb-device.txt b/Documentation/devicetree/bindings/usb/usb-device.txt new file mode 100644 index 0000000..1c35e7b --- /dev/null +++ b/Documentation/devicetree/bindings/usb/usb-device.txt @@ -0,0 +1,28 @@ +Generic USB Device Properties + +Usually, we only use device tree for hard wired USB device. +The reference binding doc is from: +http://www.firmware.org/1275/bindings/usb/usb-1_0.ps + +Required properties: +- compatible: usbVID,PID. The textual representation of VID, PID shall + be in lower case hexadecimal with leading zeroes suppressed. The + other compatible strings from the above standard binding could also + be used, but a device adhering to this binding may leave out all except + for usbVID,PID. +- reg: the port number which this device is connecting to, the range + is 1-31. + +Example: + +&usb1 { + status = "okay"; + + #address-cells = <1>; + #size-cells = <0>; + + hub: genesys@1 { + compatible = "usb5e3,608"; + reg = <1>; + }; +} diff --git a/Documentation/devicetree/bindings/usb/usb-xhci.txt b/Documentation/devicetree/bindings/usb/usb-xhci.txt index 0825732..6a17aa8 100644 --- a/Documentation/devicetree/bindings/usb/usb-xhci.txt +++ b/Documentation/devicetree/bindings/usb/usb-xhci.txt @@ -1,10 +1,23 @@ USB xHCI controllers Required properties: - - compatible: should be one of "generic-xhci", - "marvell,armada-375-xhci", "marvell,armada-380-xhci", - "renesas,xhci-r8a7790", "renesas,xhci-r8a7791", "renesas,xhci-r8a7793", - "renesas,xhci-r8a7795" (deprecated: "xhci-platform"). + - compatible: should be one or more of + + - "generic-xhci" for generic XHCI device + - "marvell,armada-375-xhci" for Armada 375 SoCs + - "marvell,armada-380-xhci" for Armada 38x SoCs + - "renesas,xhci-r8a7790" for r8a7790 SoC + - "renesas,xhci-r8a7791" for r8a7791 SoC + - "renesas,xhci-r8a7793" for r8a7793 SoC + - "renesas,xhci-r8a7795" for r8a7795 SoC + - "renesas,rcar-gen2-xhci" for a generic R-Car Gen2 compatible device + - "renesas,rcar-gen3-xhci" for a generic R-Car Gen3 compatible device + - "xhci-platform" (deprecated) + + When compatible with the generic version, nodes must list the + SoC-specific version corresponding to the platform first + followed by the generic version. + - reg: should contain address and length of the standard XHCI register set for the device. - interrupts: one XHCI interrupt should be described here. diff --git a/Documentation/devicetree/bindings/vendor-prefixes.txt b/Documentation/devicetree/bindings/vendor-prefixes.txt index 72e2c5a..86740d4 100644 --- a/Documentation/devicetree/bindings/vendor-prefixes.txt +++ b/Documentation/devicetree/bindings/vendor-prefixes.txt @@ -10,6 +10,7 @@ ad Avionic Design GmbH adapteva Adapteva, Inc. adh AD Holdings Plc. adi Analog Devices, Inc. +advantech Advantech Corporation aeroflexgaisler Aeroflex Gaisler AB al Annapurna Labs allwinner Allwinner Technology Co., Ltd. @@ -28,6 +29,7 @@ arm ARM Ltd. armadeus ARMadeus Systems SARL artesyn Artesyn Embedded Technologies Inc. asahi-kasei Asahi Kasei Corp. +atlas Atlas Scientific LLC atmel Atmel Corporation auo AU Optronics Corporation avago Avago Technologies @@ -71,6 +73,7 @@ dmo Data Modul AG ea Embedded Artists AB ebv EBV Elektronik edt Emerging Display Technologies +eeti eGalax_eMPIA Technology Inc elan Elan Microelectronic Corp. emmicro EM Microelectronic energymicro Silicon Laboratories (formerly Energy Micro AS) @@ -87,6 +90,7 @@ fcs Fairchild Semiconductor firefly Firefly focaltech FocalTech Systems Co.,Ltd fsl Freescale Semiconductor +ge General Electric Company GEFanuc GE Fanuc Intelligent Platforms Embedded Systems, Inc. gef GE Fanuc Intelligent Platforms Embedded Systems, Inc. geniatech Geniatech, Inc. @@ -111,6 +115,7 @@ hp Hewlett Packard i2se I2SE GmbH ibm International Business Machines (IBM) idt Integrated Device Technologies, Inc. +ifi Ingenieurburo Fur Ic-Technologie (I/F/I) iom Iomega Corporation img Imagination Technologies Ltd. ingenic Ingenic Semiconductor @@ -120,6 +125,7 @@ intercontrol Inter Control Group invensense InvenSense Inc. isee ISEE 2007 S.L. isil Intersil +issi Integrated Silicon Solutions Inc. jedec JEDEC Solid State Technology Association karo Ka-Ro electronics GmbH keymile Keymile GmbH @@ -170,6 +176,7 @@ opencores OpenCores.org option Option NV ortustech Ortus Technology Co., Ltd. ovti OmniVision Technologies +ORCL Oracle Corporation panasonic Panasonic Corporation parade Parade Technologies Inc. pericom Pericom Technology Inc. @@ -204,6 +211,7 @@ seagate Seagate Technology PLC semtech Semtech Corporation sgx SGX Sensortech sharp Sharp Corporation +si-en Si-En Technology Ltd. sigma Sigma Designs, Inc. sil Silicon Image silabs Silicon Laboratories @@ -226,7 +234,9 @@ st STMicroelectronics startek Startek ste ST-Ericsson stericsson ST-Ericsson +syna Synaptics Inc. synology Synology, Inc. +SUNW Sun Microsystems, Inc tbs TBS Technologies tcl Toby Churchill Ltd. technologic Technologic Systems @@ -238,8 +248,10 @@ toshiba Toshiba Corporation toumaz Toumaz tplink TP-LINK Technologies Co., Ltd. tronfy Tronfy +tronsmart Tronsmart truly Truly Semiconductors Limited upisemi uPI Semiconductor Corp. +urt United Radiant Technology Corporation usi Universal Scientific Industrial Co., Ltd. v3 V3 Semiconductor variscite Variscite Ltd. diff --git a/Documentation/devicetree/bindings/watchdog/arm,sp805.txt b/Documentation/devicetree/bindings/watchdog/arm,sp805.txt new file mode 100644 index 0000000..ca99d64 --- /dev/null +++ b/Documentation/devicetree/bindings/watchdog/arm,sp805.txt @@ -0,0 +1,17 @@ +ARM AMBA Primecell SP805 Watchdog + +Required properties: +- compatible: Should be "arm,sp805" & "arm,primecell" +- reg: Should contain location and length for watchdog timer register. +- interrupts: Should contain the list of watchdog timer interrupts. +- clocks: clocks driving the watchdog timer hardware. This list should be 2 + clocks. With 2 clocks, the order is wdogclk clock, apb_pclk. + +Example: + watchdog@66090000 { + compatible = "arm,sp805", "arm,primecell"; + reg = <0x66090000 0x1000>; + interrupts = <GIC_SPI 406 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&apb_pclk>,<&apb_pclk>; + clock-names = "wdogclk", "apb_pclk"; + }; diff --git a/Documentation/devicetree/bindings/watchdog/sbsa-gwdt.txt b/Documentation/devicetree/bindings/watchdog/sbsa-gwdt.txt new file mode 100644 index 0000000..6f2d5f9 --- /dev/null +++ b/Documentation/devicetree/bindings/watchdog/sbsa-gwdt.txt @@ -0,0 +1,31 @@ +* SBSA (Server Base System Architecture) Generic Watchdog + +The SBSA Generic Watchdog Timer is used to force a reset of the system +after two stages of timeout have elapsed. A detailed definition of the +watchdog timer can be found in the ARM document: ARM-DEN-0029 - Server +Base System Architecture (SBSA) + +Required properties: +- compatible: Should at least contain "arm,sbsa-gwdt". + +- reg: Each entry specifies the base physical address of a register frame + and the length of that frame; currently, two frames must be defined, + in this order: + 1: Watchdog control frame; + 2: Refresh frame. + +- interrupts: Should contain the Watchdog Signal 0 (WS0) SPI (Shared + Peripheral Interrupt) number of SBSA Generic Watchdog. + +Optional properties +- timeout-sec: Watchdog timeout values (in seconds). + +Example for FVP Foundation Model v8: + +watchdog@2a440000 { + compatible = "arm,sbsa-gwdt"; + reg = <0x0 0x2a440000 0 0x1000>, + <0x0 0x2a450000 0 0x1000>; + interrupts = <0 27 4>; + timeout-sec = <30>; +}; diff --git a/Documentation/devicetree/booting-without-of.txt b/Documentation/devicetree/booting-without-of.txt index 04d34f6..3f1437f 100644 --- a/Documentation/devicetree/booting-without-of.txt +++ b/Documentation/devicetree/booting-without-of.txt @@ -16,6 +16,7 @@ Table of Contents 2) Entry point for arch/powerpc 3) Entry point for arch/x86 4) Entry point for arch/mips/bmips + 5) Entry point for arch/sh II - The DT block format 1) Header @@ -316,6 +317,18 @@ it with special cases. This convention is defined for 32-bit systems only, as there are not currently any 64-bit BMIPS implementations. +5) Entry point for arch/sh +-------------------------- + + Device-tree-compatible SH bootloaders are expected to provide the physical + address of the device tree blob in r4. Since legacy bootloaders did not + guarantee any particular initial register state, kernels built to + inter-operate with old bootloaders must either use a builtin DTB or + select a legacy board option (something other than CONFIG_SH_DEVICE_TREE) + that does not use device tree. Support for the latter is being phased out + in favor of device tree. + + II - The DT block format ======================== |