diff options
Diffstat (limited to 'Documentation/devicetree')
5 files changed, 107 insertions, 7 deletions
diff --git a/Documentation/devicetree/bindings/pci/altera-pcie-msi.txt b/Documentation/devicetree/bindings/pci/altera-pcie-msi.txt new file mode 100644 index 0000000..09cd3bc --- /dev/null +++ b/Documentation/devicetree/bindings/pci/altera-pcie-msi.txt @@ -0,0 +1,28 @@ +* Altera PCIe MSI controller + +Required properties: +- compatible: should contain "altr,msi-1.0" +- reg: specifies the physical base address of the controller and + the length of the memory mapped region. +- reg-names: must include the following entries: + "csr": CSR registers + "vector_slave": vectors slave port region +- interrupt-parent: interrupt source phandle. +- interrupts: specifies the interrupt source of the parent interrupt + controller. The format of the interrupt specifier depends on the + parent interrupt controller. +- num-vectors: number of vectors, range 1 to 32. +- msi-controller: indicates that this is MSI controller node + + +Example +msi0: msi@0xFF200000 { + compatible = "altr,msi-1.0"; + reg = <0xFF200000 0x00000010 + 0xFF200010 0x00000080>; + reg-names = "csr", "vector_slave"; + interrupt-parent = <&hps_0_arm_gic_0>; + interrupts = <0 42 4>; + msi-controller; + num-vectors = <32>; +}; diff --git a/Documentation/devicetree/bindings/pci/altera-pcie.txt b/Documentation/devicetree/bindings/pci/altera-pcie.txt new file mode 100644 index 0000000..2951a6a --- /dev/null +++ b/Documentation/devicetree/bindings/pci/altera-pcie.txt @@ -0,0 +1,49 @@ +* Altera PCIe controller + +Required properties: +- compatible : should contain "altr,pcie-root-port-1.0" +- reg: a list of physical base address and length for TXS and CRA. +- reg-names: must include the following entries: + "Txs": TX slave port region + "Cra": Control register access region +- interrupt-parent: interrupt source phandle. +- interrupts: specifies the interrupt source of the parent interrupt controller. + The format of the interrupt specifier depends on the parent interrupt + controller. +- device_type: must be "pci" +- #address-cells: set to <3> +- #size-cells: set to <2> +- #interrupt-cells: set to <1> +- ranges: describes the translation of addresses for root ports and standard + PCI regions. +- interrupt-map-mask and interrupt-map: standard PCI properties to define the + mapping of the PCIe interface to interrupt numbers. + +Optional properties: +- msi-parent: Link to the hardware entity that serves as the MSI controller for this PCIe + controller. +- bus-range: PCI bus numbers covered + +Example + pcie_0: pcie@0xc00000000 { + compatible = "altr,pcie-root-port-1.0"; + reg = <0xc0000000 0x20000000>, + <0xff220000 0x00004000>; + reg-names = "Txs", "Cra"; + interrupt-parent = <&hps_0_arm_gic_0>; + interrupts = <0 40 4>; + interrupt-controller; + #interrupt-cells = <1>; + bus-range = <0x0 0xFF>; + device_type = "pci"; + msi-parent = <&msi_to_gic_gen_0>; + #address-cells = <3>; + #size-cells = <2>; + interrupt-map-mask = <0 0 0 7>; + interrupt-map = <0 0 0 1 &pcie_0 1>, + <0 0 0 2 &pcie_0 2>, + <0 0 0 3 &pcie_0 3>, + <0 0 0 4 &pcie_0 4>; + ranges = <0x82000000 0x00000000 0x00000000 0xc0000000 0x00000000 0x10000000 + 0x82000000 0x00000000 0x10000000 0xd0000000 0x00000000 0x10000000>; + }; diff --git a/Documentation/devicetree/bindings/pci/brcm,iproc-pcie.txt b/Documentation/devicetree/bindings/pci/brcm,iproc-pcie.txt index f7ce50e..45c2a80 100644 --- a/Documentation/devicetree/bindings/pci/brcm,iproc-pcie.txt +++ b/Documentation/devicetree/bindings/pci/brcm,iproc-pcie.txt @@ -17,6 +17,21 @@ Optional properties: - phys: phandle of the PCIe PHY device - phy-names: must be "pcie-phy" +- brcm,pcie-ob: Some iProc SoCs do not have the outbound address mapping done +by the ASIC after power on reset. In this case, SW needs to configure it + +If the brcm,pcie-ob property is present, the following properties become +effective: + +Required: +- brcm,pcie-ob-axi-offset: The offset from the AXI address to the internal +address used by the iProc PCIe core (not the PCIe address) +- brcm,pcie-ob-window-size: The outbound address mapping window size (in MB) + +Optional: +- brcm,pcie-ob-oarr-size: Some iProc SoCs need the OARR size bit to be set to +increase the outbound window size + Example: pcie0: pcie@18012000 { compatible = "brcm,iproc-pcie"; @@ -38,6 +53,11 @@ Example: phys = <&phy 0 5>; phy-names = "pcie-phy"; + + brcm,pcie-ob; + brcm,pcie-ob-oarr-size; + brcm,pcie-ob-axi-offset = <0x00000000>; + brcm,pcie-ob-window-size = <256>; }; pcie1: pcie@18013000 { diff --git a/Documentation/devicetree/bindings/pci/designware-pcie.txt b/Documentation/devicetree/bindings/pci/designware-pcie.txt index 9f4faa8..5b0853d 100644 --- a/Documentation/devicetree/bindings/pci/designware-pcie.txt +++ b/Documentation/devicetree/bindings/pci/designware-pcie.txt @@ -15,14 +15,16 @@ Required properties: to define the mapping of the PCIe interface to interrupt numbers. - num-lanes: number of lanes to use -- clocks: Must contain an entry for each entry in clock-names. - See ../clocks/clock-bindings.txt for details. -- clock-names: Must include the following entries: - - "pcie" - - "pcie_bus" Optional properties: +- num-lanes: number of lanes to use (this property should be specified unless + the link is brought already up in BIOS) - reset-gpio: gpio pin number of power good signal - bus-range: PCI bus numbers covered (it is recommended for new devicetrees to specify this property, to keep backwards compatibility a range of 0x00-0xff is assumed if not present) +- clocks: Must contain an entry for each entry in clock-names. + See ../clocks/clock-bindings.txt for details. +- clock-names: Must include the following entries: + - "pcie" + - "pcie_bus" diff --git a/Documentation/devicetree/bindings/pci/host-generic-pci.txt b/Documentation/devicetree/bindings/pci/host-generic-pci.txt index cf3e205..3f1d3fc 100644 --- a/Documentation/devicetree/bindings/pci/host-generic-pci.txt +++ b/Documentation/devicetree/bindings/pci/host-generic-pci.txt @@ -34,8 +34,9 @@ Properties of the host controller node: - #size-cells : Must be 2. - reg : The Configuration Space base address and size, as accessed - from the parent bus. - + from the parent bus. The base address corresponds to + the first bus in the "bus-range" property. If no + "bus-range" is specified, this will be bus 0 (the default). Properties of the /chosen node: |