diff options
Diffstat (limited to 'Documentation')
-rw-r--r-- | Documentation/hwmon/smm665 | 157 |
1 files changed, 157 insertions, 0 deletions
diff --git a/Documentation/hwmon/smm665 b/Documentation/hwmon/smm665 new file mode 100644 index 0000000..3820fc9 --- /dev/null +++ b/Documentation/hwmon/smm665 @@ -0,0 +1,157 @@ +Kernel driver smm665 +==================== + +Supported chips: + * Summit Microelectronics SMM465 + Prefix: 'smm465' + Addresses scanned: - + Datasheet: + http://www.summitmicro.com/prod_select/summary/SMM465/SMM465DS.pdf + * Summit Microelectronics SMM665, SMM665B + Prefix: 'smm665' + Addresses scanned: - + Datasheet: + http://www.summitmicro.com/prod_select/summary/SMM665/SMM665B_2089_20.pdf + * Summit Microelectronics SMM665C + Prefix: 'smm665c' + Addresses scanned: - + Datasheet: + http://www.summitmicro.com/prod_select/summary/SMM665C/SMM665C_2125.pdf + * Summit Microelectronics SMM764 + Prefix: 'smm764' + Addresses scanned: - + Datasheet: + http://www.summitmicro.com/prod_select/summary/SMM764/SMM764_2098.pdf + * Summit Microelectronics SMM766, SMM766B + Prefix: 'smm766' + Addresses scanned: - + Datasheets: + http://www.summitmicro.com/prod_select/summary/SMM766/SMM766_2086.pdf + http://www.summitmicro.com/prod_select/summary/SMM766B/SMM766B_2122.pdf + +Author: Guenter Roeck <guenter.roeck@ericsson.com> + + +Module Parameters +----------------- + +* vref: int + Default: 1250 (mV) + Reference voltage on VREF_ADC pin in mV. It should not be necessary to set + this parameter unless a non-default reference voltage is used. + + +Description +----------- + +[From datasheet] The SMM665 is an Active DC Output power supply Controller +that monitors, margins and cascade sequences power. The part monitors six +power supply channels as well as VDD, 12V input, two general-purpose analog +inputs and an internal temperature sensor using a 10-bit ADC. + +Each monitored channel has its own high and low limits, plus a critical +limit. + +Support for SMM465, SMM764, and SMM766 has been implemented but is untested. + + +Usage Notes +----------- + +This driver does not probe for devices, since there is no register which +can be safely used to identify the chip. You will have to instantiate +the devices explicitly. When instantiating the device, you have to specify +its configuration register address. + +Example: the following will load the driver for an SMM665 at address 0x57 +on I2C bus #1: +$ modprobe smm665 +$ echo smm665 0x57 > /sys/bus/i2c/devices/i2c-1/new_device + + +Sysfs entries +------------- + +This driver uses the values in the datasheet to convert ADC register values +into the values specified in the sysfs-interface document. All attributes are +read only. + +Min, max, lcrit, and crit values are used by the chip to trigger external signals +and/or other activity. Triggered signals can include HEALTHY, RST, Power Off, +or Fault depending on the chip configuration. The driver reports values as lcrit +or crit if exceeding the limits triggers RST, Power Off, or Fault, and as min or +max otherwise. For details please see the SMM665 datasheet. + +For SMM465 and SMM764, values for Channel E and F are reported but undefined. + +in1_input 12V input voltage (mV) +in2_input 3.3V (VDD) input voltage (mV) +in3_input Channel A voltage (mV) +in4_input Channel B voltage (mV) +in5_input Channel C voltage (mV) +in6_input Channel D voltage (mV) +in7_input Channel E voltage (mV) +in8_input Channel F voltage (mV) +in9_input AIN1 voltage (mV) +in10_input AIN2 voltage (mV) + +in1_min 12v input minimum voltage (mV) +in2_min 3.3V (VDD) input minimum voltage (mV) +in3_min Channel A minimum voltage (mV) +in4_min Channel B minimum voltage (mV) +in5_min Channel C minimum voltage (mV) +in6_min Channel D minimum voltage (mV) +in7_min Channel E minimum voltage (mV) +in8_min Channel F minimum voltage (mV) +in9_min AIN1 minimum voltage (mV) +in10_min AIN2 minimum voltage (mV) + +in1_max 12v input maximum voltage (mV) +in2_max 3.3V (VDD) input maximum voltage (mV) +in3_max Channel A maximum voltage (mV) +in4_max Channel B maximum voltage (mV) +in5_max Channel C maximum voltage (mV) +in6_max Channel D maximum voltage (mV) +in7_max Channel E maximum voltage (mV) +in8_max Channel F maximum voltage (mV) +in9_max AIN1 maximum voltage (mV) +in10_max AIN2 maximum voltage (mV) + +in1_lcrit 12v input critical minimum voltage (mV) +in2_lcrit 3.3V (VDD) input critical minimum voltage (mV) +in3_lcrit Channel A critical minimum voltage (mV) +in4_lcrit Channel B critical minimum voltage (mV) +in5_lcrit Channel C critical minimum voltage (mV) +in6_lcrit Channel D critical minimum voltage (mV) +in7_lcrit Channel E critical minimum voltage (mV) +in8_lcrit Channel F critical minimum voltage (mV) +in9_lcrit AIN1 critical minimum voltage (mV) +in10_lcrit AIN2 critical minimum voltage (mV) + +in1_crit 12v input critical maximum voltage (mV) +in2_crit 3.3V (VDD) input critical maximum voltage (mV) +in3_crit Channel A critical maximum voltage (mV) +in4_crit Channel B critical maximum voltage (mV) +in5_crit Channel C critical maximum voltage (mV) +in6_crit Channel D critical maximum voltage (mV) +in7_crit Channel E critical maximum voltage (mV) +in8_crit Channel F critical maximum voltage (mV) +in9_crit AIN1 critical maximum voltage (mV) +in10_crit AIN2 critical maximum voltage (mV) + +in1_crit_alarm 12v input critical alarm +in2_crit_alarm 3.3V (VDD) input critical alarm +in3_crit_alarm Channel A critical alarm +in4_crit_alarm Channel B critical alarm +in5_crit_alarm Channel C critical alarm +in6_crit_alarm Channel D critical alarm +in7_crit_alarm Channel E critical alarm +in8_crit_alarm Channel F critical alarm +in9_crit_alarm AIN1 critical alarm +in10_crit_alarm AIN2 critical alarm + +temp1_input Chip tempererature +temp1_min Mimimum chip tempererature +temp1_max Maximum chip tempererature +temp1_crit Critical chip tempererature +temp1_crit_alarm Temperature critical alarm |