diff options
Diffstat (limited to 'Documentation')
-rw-r--r-- | Documentation/IPMI.txt | 7 | ||||
-rw-r--r-- | Documentation/arm/keystone/Overview.txt | 18 | ||||
-rw-r--r-- | Documentation/block/null_blk.txt | 3 | ||||
-rw-r--r-- | Documentation/devicetree/bindings/thermal/rockchip-thermal.txt | 4 | ||||
-rw-r--r-- | Documentation/i2c/busses/i2c-i801 | 1 | ||||
-rw-r--r-- | Documentation/kernel-parameters.txt | 3 |
6 files changed, 12 insertions, 24 deletions
diff --git a/Documentation/IPMI.txt b/Documentation/IPMI.txt index 31d1d65..c0d8788 100644 --- a/Documentation/IPMI.txt +++ b/Documentation/IPMI.txt @@ -587,7 +587,7 @@ used to control it: modprobe ipmi_watchdog timeout=<t> pretimeout=<t> action=<action type> preaction=<preaction type> preop=<preop type> start_now=x - nowayout=x ifnum_to_use=n + nowayout=x ifnum_to_use=n panic_wdt_timeout=<t> ifnum_to_use specifies which interface the watchdog timer should use. The default is -1, which means to pick the first one registered. @@ -597,7 +597,9 @@ is the amount of seconds before the reset that the pre-timeout panic will occur (if pretimeout is zero, then pretimeout will not be enabled). Note that the pretimeout is the time before the final timeout. So if the timeout is 50 seconds and the pretimeout is 10 seconds, then the pretimeout -will occur in 40 second (10 seconds before the timeout). +will occur in 40 second (10 seconds before the timeout). The panic_wdt_timeout +is the value of timeout which is set on kernel panic, in order to let actions +such as kdump to occur during panic. The action may be "reset", "power_cycle", or "power_off", and specifies what to do when the timer times out, and defaults to @@ -634,6 +636,7 @@ for configuring the watchdog: ipmi_watchdog.preop=<preop type> ipmi_watchdog.start_now=x ipmi_watchdog.nowayout=x + ipmi_watchdog.panic_wdt_timeout=<t> The options are the same as the module parameter options. diff --git a/Documentation/arm/keystone/Overview.txt b/Documentation/arm/keystone/Overview.txt index f17bc4c..400c0c2 100644 --- a/Documentation/arm/keystone/Overview.txt +++ b/Documentation/arm/keystone/Overview.txt @@ -49,24 +49,6 @@ specified through DTS. Following are the DTS used:- The device tree documentation for the keystone machines are located at Documentation/devicetree/bindings/arm/keystone/keystone.txt -Known issues & workaround -------------------------- - -Some of the device drivers used on keystone are re-used from that from -DaVinci and other TI SoCs. These device drivers may use clock APIs directly. -Some of the keystone specific drivers such as netcp uses run time power -management API instead to enable clock. As this API has limitations on -keystone, following workaround is needed to boot Linux. - - Add 'clk_ignore_unused' to the bootargs env variable in u-boot. Otherwise - clock frameworks will try to disable clocks that are unused and disable - the hardware. This is because netcp related power domain and clock - domains are enabled in u-boot as run time power management API currently - doesn't enable clocks for netcp due to a limitation. This workaround is - expected to be removed in the future when proper API support becomes - available. Until then, this work around is needed. - - Document Author --------------- Murali Karicheri <m-karicheri2@ti.com> diff --git a/Documentation/block/null_blk.txt b/Documentation/block/null_blk.txt index 2f6c6ff..d8880ca 100644 --- a/Documentation/block/null_blk.txt +++ b/Documentation/block/null_blk.txt @@ -70,3 +70,6 @@ use_per_node_hctx=[0/1]: Default: 0 parameter. 1: The multi-queue block layer is instantiated with a hardware dispatch queue for each CPU node in the system. + +use_lightnvm=[0/1]: Default: 0 + Register device with LightNVM. Requires blk-mq to be used. diff --git a/Documentation/devicetree/bindings/thermal/rockchip-thermal.txt b/Documentation/devicetree/bindings/thermal/rockchip-thermal.txt index b38200d..0dfa60d 100644 --- a/Documentation/devicetree/bindings/thermal/rockchip-thermal.txt +++ b/Documentation/devicetree/bindings/thermal/rockchip-thermal.txt @@ -1,7 +1,9 @@ * Temperature Sensor ADC (TSADC) on rockchip SoCs Required properties: -- compatible : "rockchip,rk3288-tsadc" +- compatible : should be "rockchip,<name>-tsadc" + "rockchip,rk3288-tsadc": found on RK3288 SoCs + "rockchip,rk3368-tsadc": found on RK3368 SoCs - reg : physical base address of the controller and length of memory mapped region. - interrupts : The interrupt number to the cpu. The interrupt specifier format diff --git a/Documentation/i2c/busses/i2c-i801 b/Documentation/i2c/busses/i2c-i801 index 6a4b1af..1bba38d 100644 --- a/Documentation/i2c/busses/i2c-i801 +++ b/Documentation/i2c/busses/i2c-i801 @@ -32,6 +32,7 @@ Supported adapters: * Intel Sunrise Point-LP (PCH) * Intel DNV (SOC) * Intel Broxton (SOC) + * Intel Lewisburg (PCH) Datasheets: Publicly available at the Intel website On Intel Patsburg and later chipsets, both the normal host SMBus controller diff --git a/Documentation/kernel-parameters.txt b/Documentation/kernel-parameters.txt index f8aae63..742f69d 100644 --- a/Documentation/kernel-parameters.txt +++ b/Documentation/kernel-parameters.txt @@ -1583,9 +1583,6 @@ bytes respectively. Such letter suffixes can also be entirely omitted. hwp_only Only load intel_pstate on systems which support hardware P state control (HWP) if available. - no_acpi - Don't use ACPI processor performance control objects - _PSS and _PPC specified limits. intremap= [X86-64, Intel-IOMMU] on enable Interrupt Remapping (default) |