diff options
Diffstat (limited to 'Documentation')
15 files changed, 204 insertions, 22 deletions
diff --git a/Documentation/devicetree/bindings/display/etnaviv/etnaviv-drm.txt b/Documentation/devicetree/bindings/display/etnaviv/etnaviv-drm.txt new file mode 100644 index 0000000..ed5e0a7 --- /dev/null +++ b/Documentation/devicetree/bindings/display/etnaviv/etnaviv-drm.txt @@ -0,0 +1,54 @@ +Etnaviv DRM master device +========================= + +The Etnaviv DRM master device is a virtual device needed to list all +Vivante GPU cores that comprise the GPU subsystem. + +Required properties: +- compatible: Should be one of + "fsl,imx-gpu-subsystem" + "marvell,dove-gpu-subsystem" +- cores: Should contain a list of phandles pointing to Vivante GPU devices + +example: + +gpu-subsystem { + compatible = "fsl,imx-gpu-subsystem"; + cores = <&gpu_2d>, <&gpu_3d>; +}; + + +Vivante GPU core devices +======================== + +Required properties: +- compatible: Should be "vivante,gc" + A more specific compatible is not needed, as the cores contain chip + identification registers at fixed locations, which provide all the + necessary information to the driver. +- reg: should be register base and length as documented in the + datasheet +- interrupts: Should contain the cores interrupt line +- clocks: should contain one clock for entry in clock-names + see Documentation/devicetree/bindings/clock/clock-bindings.txt +- clock-names: + - "bus": AXI/register clock + - "core": GPU core clock + - "shader": Shader clock (only required if GPU has feature PIPE_3D) + +Optional properties: +- power-domains: a power domain consumer specifier according to + Documentation/devicetree/bindings/power/power_domain.txt + +example: + +gpu_3d: gpu@00130000 { + compatible = "vivante,gc"; + reg = <0x00130000 0x4000>; + interrupts = <0 9 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&clks IMX6QDL_CLK_GPU3D_AXI>, + <&clks IMX6QDL_CLK_GPU3D_CORE>, + <&clks IMX6QDL_CLK_GPU3D_SHADER>; + clock-names = "bus", "core", "shader"; + power-domains = <&gpc 1>; +}; diff --git a/Documentation/devicetree/bindings/display/panel/boe,tv080wum-nl0.txt b/Documentation/devicetree/bindings/display/panel/boe,tv080wum-nl0.txt new file mode 100644 index 0000000..50be5e2 --- /dev/null +++ b/Documentation/devicetree/bindings/display/panel/boe,tv080wum-nl0.txt @@ -0,0 +1,7 @@ +Boe Corporation 8.0" WUXGA TFT LCD panel + +Required properties: +- compatible: should be "boe,tv080wum-nl0" + +This binding is compatible with the simple-panel binding, which is specified +in simple-panel.txt in this directory. diff --git a/Documentation/devicetree/bindings/display/panel/innolux,g121x1-l03.txt b/Documentation/devicetree/bindings/display/panel/innolux,g121x1-l03.txt new file mode 100644 index 0000000..6497446 --- /dev/null +++ b/Documentation/devicetree/bindings/display/panel/innolux,g121x1-l03.txt @@ -0,0 +1,7 @@ +Innolux Corporation 12.1" G121X1-L03 XGA (1024x768) TFT LCD panel + +Required properties: +- compatible: should be "innolux,g121x1-l03" + +This binding is compatible with the simple-panel binding, which is specified +in simple-panel.txt in this directory. diff --git a/Documentation/devicetree/bindings/display/panel/kyo,tcg121xglp.txt b/Documentation/devicetree/bindings/display/panel/kyo,tcg121xglp.txt new file mode 100644 index 0000000..a8e940f --- /dev/null +++ b/Documentation/devicetree/bindings/display/panel/kyo,tcg121xglp.txt @@ -0,0 +1,7 @@ +Kyocera Corporation 12.1" XGA (1024x768) TFT LCD panel + +Required properties: +- compatible: should be "kyo,tcg121xglp" + +This binding is compatible with the simple-panel binding, which is specified +in simple-panel.txt in this directory. diff --git a/Documentation/devicetree/bindings/display/panel/panasonic,vvx10f034n00.txt b/Documentation/devicetree/bindings/display/panel/panasonic,vvx10f034n00.txt new file mode 100644 index 0000000..37dedf6 --- /dev/null +++ b/Documentation/devicetree/bindings/display/panel/panasonic,vvx10f034n00.txt @@ -0,0 +1,20 @@ +Panasonic 10" WUXGA TFT LCD panel + +Required properties: +- compatible: should be "panasonic,vvx10f034n00" +- reg: DSI virtual channel of the peripheral +- power-supply: phandle of the regulator that provides the supply voltage + +Optional properties: +- backlight: phandle of the backlight device attached to the panel + +Example: + + mdss_dsi@fd922800 { + panel@0 { + compatible = "panasonic,vvx10f034n00"; + reg = <0>; + power-supply = <&vreg_vsp>; + backlight = <&lp8566_wled>; + }; + }; diff --git a/Documentation/devicetree/bindings/display/panel/qiaodian,qd43003c0-40.txt b/Documentation/devicetree/bindings/display/panel/qiaodian,qd43003c0-40.txt new file mode 100644 index 0000000..0fbdab8 --- /dev/null +++ b/Documentation/devicetree/bindings/display/panel/qiaodian,qd43003c0-40.txt @@ -0,0 +1,7 @@ +QiaoDian XianShi Corporation 4"3 TFT LCD panel + +Required properties: +- compatible: should be "qiaodian,qd43003c0-40" + +This binding is compatible with the simple-panel binding, which is specified +in simple-panel.txt in this directory. diff --git a/Documentation/devicetree/bindings/display/panel/sharp,ls043t1le01.txt b/Documentation/devicetree/bindings/display/panel/sharp,ls043t1le01.txt new file mode 100644 index 0000000..3770a11 --- /dev/null +++ b/Documentation/devicetree/bindings/display/panel/sharp,ls043t1le01.txt @@ -0,0 +1,22 @@ +Sharp Microelectronics 4.3" qHD TFT LCD panel + +Required properties: +- compatible: should be "sharp,ls043t1le01-qhd" +- reg: DSI virtual channel of the peripheral +- power-supply: phandle of the regulator that provides the supply voltage + +Optional properties: +- backlight: phandle of the backlight device attached to the panel +- reset-gpios: a GPIO spec for the reset pin + +Example: + + mdss_dsi@fd922800 { + panel@0 { + compatible = "sharp,ls043t1le01-qhd"; + reg = <0>; + avdd-supply = <&pm8941_l22>; + backlight = <&pm8941_wled>; + reset-gpios = <&pm8941_gpios 19 GPIO_ACTIVE_HIGH>; + }; + }; diff --git a/Documentation/devicetree/bindings/display/rockchip/dw_mipi_dsi_rockchip.txt b/Documentation/devicetree/bindings/display/rockchip/dw_mipi_dsi_rockchip.txt new file mode 100644 index 0000000..1753f0c --- /dev/null +++ b/Documentation/devicetree/bindings/display/rockchip/dw_mipi_dsi_rockchip.txt @@ -0,0 +1,60 @@ +Rockchip specific extensions to the Synopsys Designware MIPI DSI +================================ + +Required properties: +- #address-cells: Should be <1>. +- #size-cells: Should be <0>. +- compatible: "rockchip,rk3288-mipi-dsi", "snps,dw-mipi-dsi". +- reg: Represent the physical address range of the controller. +- interrupts: Represent the controller's interrupt to the CPU(s). +- clocks, clock-names: Phandles to the controller's pll reference + clock(ref) and APB clock(pclk), as described in [1]. +- rockchip,grf: this soc should set GRF regs to mux vopl/vopb. +- ports: contain a port node with endpoint definitions as defined in [2]. + For vopb,set the reg = <0> and set the reg = <1> for vopl. + +[1] Documentation/devicetree/bindings/clock/clock-bindings.txt +[2] Documentation/devicetree/bindings/media/video-interfaces.txt + +Example: + mipi_dsi: mipi@ff960000 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "rockchip,rk3288-mipi-dsi", "snps,dw-mipi-dsi"; + reg = <0xff960000 0x4000>; + interrupts = <GIC_SPI 83 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&cru SCLK_MIPI_24M>, <&cru PCLK_MIPI_DSI0>; + clock-names = "ref", "pclk"; + rockchip,grf = <&grf>; + status = "okay"; + + ports { + #address-cells = <1>; + #size-cells = <0>; + reg = <1>; + + mipi_in: port { + #address-cells = <1>; + #size-cells = <0>; + mipi_in_vopb: endpoint@0 { + reg = <0>; + remote-endpoint = <&vopb_out_mipi>; + }; + mipi_in_vopl: endpoint@1 { + reg = <1>; + remote-endpoint = <&vopl_out_mipi>; + }; + }; + }; + + panel { + compatible ="boe,tv080wum-nl0"; + reg = <0>; + + enable-gpios = <&gpio7 3 GPIO_ACTIVE_HIGH>; + pinctrl-names = "default"; + pinctrl-0 = <&lcd_en>; + backlight = <&backlight>; + status = "okay"; + }; + }; diff --git a/Documentation/devicetree/bindings/display/rockchip/rockchip-vop.txt b/Documentation/devicetree/bindings/display/rockchip/rockchip-vop.txt index d15351f..5489b59 100644 --- a/Documentation/devicetree/bindings/display/rockchip/rockchip-vop.txt +++ b/Documentation/devicetree/bindings/display/rockchip/rockchip-vop.txt @@ -7,6 +7,7 @@ buffer to an external LCD interface. Required properties: - compatible: value should be one of the following "rockchip,rk3288-vop"; + "rockchip,rk3036-vop"; - interrupts: should contain a list of all VOP IP block interrupts in the order: VSYNC, LCD_SYSTEM. The interrupt specifier diff --git a/Documentation/devicetree/bindings/dma/ti-edma.txt b/Documentation/devicetree/bindings/dma/ti-edma.txt index d3d0a4f..079b42a 100644 --- a/Documentation/devicetree/bindings/dma/ti-edma.txt +++ b/Documentation/devicetree/bindings/dma/ti-edma.txt @@ -22,8 +22,7 @@ Required properties: Optional properties: - ti,hwmods: Name of the hwmods associated to the eDMA CC - ti,edma-memcpy-channels: List of channels allocated to be used for memcpy, iow - these channels will be SW triggered channels. The list must - contain 16 bits numbers, see example. + these channels will be SW triggered channels. See example. - ti,edma-reserved-slot-ranges: PaRAM slot ranges which should not be used by the driver, they are allocated to be used by for example the DSP. See example. @@ -56,10 +55,9 @@ edma: edma@49000000 { ti,tptcs = <&edma_tptc0 7>, <&edma_tptc1 7>, <&edma_tptc2 0>; /* Channel 20 and 21 is allocated for memcpy */ - ti,edma-memcpy-channels = /bits/ 16 <20 21>; - /* The following PaRAM slots are reserved: 35-45 and 100-110 */ - ti,edma-reserved-slot-ranges = /bits/ 16 <35 10>, - /bits/ 16 <100 10>; + ti,edma-memcpy-channels = <20 21>; + /* The following PaRAM slots are reserved: 35-44 and 100-109 */ + ti,edma-reserved-slot-ranges = <35 10>, <100 10>; }; edma_tptc0: tptc@49800000 { diff --git a/Documentation/devicetree/bindings/gpio/gpio-mpc8xxx.txt b/Documentation/devicetree/bindings/gpio/gpio-mpc8xxx.txt index f2455c5..120bc49 100644 --- a/Documentation/devicetree/bindings/gpio/gpio-mpc8xxx.txt +++ b/Documentation/devicetree/bindings/gpio/gpio-mpc8xxx.txt @@ -11,6 +11,10 @@ Required properties: 0 = active high 1 = active low +Optional properties: +- little-endian : GPIO registers are used as little endian. If not + present registers are used as big endian by default. + Example: gpio0: gpio@1100 { diff --git a/Documentation/devicetree/bindings/input/sun4i-lradc-keys.txt b/Documentation/devicetree/bindings/input/sun4i-lradc-keys.txt index b9c32f6..4357e49 100644 --- a/Documentation/devicetree/bindings/input/sun4i-lradc-keys.txt +++ b/Documentation/devicetree/bindings/input/sun4i-lradc-keys.txt @@ -12,7 +12,7 @@ Each key is represented as a sub-node of "allwinner,sun4i-a10-lradc-keys": Required subnode-properties: - label: Descriptive name of the key. - linux,code: Keycode to emit. - - channel: Channel this key is attached to, mut be 0 or 1. + - channel: Channel this key is attached to, must be 0 or 1. - voltage: Voltage in µV at lradc input when this key is pressed. Example: diff --git a/Documentation/devicetree/bindings/mtd/partition.txt b/Documentation/devicetree/bindings/mtd/partition.txt index f1e2a02..1c63e40 100644 --- a/Documentation/devicetree/bindings/mtd/partition.txt +++ b/Documentation/devicetree/bindings/mtd/partition.txt @@ -6,7 +6,9 @@ used for what purposes, but which don't use an on-flash partition table such as RedBoot. The partition table should be a subnode of the mtd node and should be named -'partitions'. Partitions are defined in subnodes of the partitions node. +'partitions'. This node should have the following property: +- compatible : (required) must be "fixed-partitions" +Partitions are then defined in subnodes of the partitions node. For backwards compatibility partitions as direct subnodes of the mtd device are supported. This use is discouraged. @@ -36,6 +38,7 @@ Examples: flash@0 { partitions { + compatible = "fixed-partitions"; #address-cells = <1>; #size-cells = <1>; @@ -53,6 +56,7 @@ flash@0 { flash@1 { partitions { + compatible = "fixed-partitions"; #address-cells = <1>; #size-cells = <2>; @@ -66,6 +70,7 @@ flash@1 { flash@2 { partitions { + compatible = "fixed-partitions"; #address-cells = <2>; #size-cells = <2>; diff --git a/Documentation/devicetree/bindings/vendor-prefixes.txt b/Documentation/devicetree/bindings/vendor-prefixes.txt index 55df1d4..b123731 100644 --- a/Documentation/devicetree/bindings/vendor-prefixes.txt +++ b/Documentation/devicetree/bindings/vendor-prefixes.txt @@ -33,6 +33,7 @@ auo AU Optronics Corporation avago Avago Technologies avic Shanghai AVIC Optoelectronics Co., Ltd. axis Axis Communications AB +boe BOE Technology Group Co., Ltd. bosch Bosch Sensortec GmbH boundary Boundary Devices Inc. brcm Broadcom Corporation @@ -123,6 +124,7 @@ jedec JEDEC Solid State Technology Association karo Ka-Ro electronics GmbH keymile Keymile GmbH kinetic Kinetic Technologies +kyo Kyocera Corporation lacie LaCie lantiq Lantiq Semiconductor lenovo Lenovo Group Ltd. @@ -180,6 +182,7 @@ qca Qualcomm Atheros, Inc. qcom Qualcomm Technologies, Inc qemu QEMU, a generic and open source machine emulator and virtualizer qi Qi Hardware +qiaodian QiaoDian XianShi Corporation qnap QNAP Systems, Inc. radxa Radxa raidsonic RaidSonic Technology GmbH @@ -238,6 +241,7 @@ v3 V3 Semiconductor variscite Variscite Ltd. via VIA Technologies, Inc. virtio Virtual I/O Device Specification, developed by the OASIS consortium +vivante Vivante Corporation voipac Voipac Technologies s.r.o. wexler Wexler winbond Winbond Electronics corp. diff --git a/Documentation/networking/e100.txt b/Documentation/networking/e100.txt index f862cf3..42ddbd4 100644 --- a/Documentation/networking/e100.txt +++ b/Documentation/networking/e100.txt @@ -181,17 +181,3 @@ For general information, go to the Intel support website at: If an issue is identified with the released source code on the supported kernel with a supported adapter, email the specific information related to the issue to e1000-devel@lists.sourceforge.net. - - -License -======= - -This software program is released under the terms of a license agreement -between you ('Licensee') and Intel. Do not use or load this software or any -associated materials (collectively, the 'Software') until you have carefully -read the full terms and conditions of the file COPYING located in this software -package. By loading or using the Software, you agree to the terms of this -Agreement. If you do not agree with the terms of this Agreement, do not install -or use the Software. - -* Other names and brands may be claimed as the property of others. |