diff options
Diffstat (limited to 'Documentation')
20 files changed, 127 insertions, 53 deletions
diff --git a/Documentation/ABI/testing/sysfs-devices-system-cpu b/Documentation/ABI/testing/sysfs-devices-system-cpu index 99983e6..da95513 100644 --- a/Documentation/ABI/testing/sysfs-devices-system-cpu +++ b/Documentation/ABI/testing/sysfs-devices-system-cpu @@ -162,7 +162,7 @@ Description: Discover CPUs in the same CPU frequency coordination domain What: /sys/devices/system/cpu/cpu*/cache/index3/cache_disable_{0,1} Date: August 2008 KernelVersion: 2.6.27 -Contact: discuss@x86-64.org +Contact: Linux kernel mailing list <linux-kernel@vger.kernel.org> Description: Disable L3 cache indices These files exist in every CPU's cache/index3 directory. Each diff --git a/Documentation/IPMI.txt b/Documentation/IPMI.txt index 653d5d7..31d1d65 100644 --- a/Documentation/IPMI.txt +++ b/Documentation/IPMI.txt @@ -505,7 +505,10 @@ at module load time (for a module) with: The addresses are normal I2C addresses. The adapter is the string name of the adapter, as shown in /sys/class/i2c-adapter/i2c-<n>/name. -It is *NOT* i2c-<n> itself. +It is *NOT* i2c-<n> itself. Also, the comparison is done ignoring +spaces, so if the name is "This is an I2C chip" you can say +adapter_name=ThisisanI2cchip. This is because it's hard to pass in +spaces in kernel parameters. The debug flags are bit flags for each BMC found, they are: IPMI messages: 1, driver state: 2, timing: 4, I2C probe: 8 diff --git a/Documentation/acpi/enumeration.txt b/Documentation/acpi/enumeration.txt index 750401f..15dfce7 100644 --- a/Documentation/acpi/enumeration.txt +++ b/Documentation/acpi/enumeration.txt @@ -253,7 +253,7 @@ input driver: GPIO support ~~~~~~~~~~~~ ACPI 5 introduced two new resources to describe GPIO connections: GpioIo -and GpioInt. These resources are used be used to pass GPIO numbers used by +and GpioInt. These resources can be used to pass GPIO numbers used by the device to the driver. ACPI 5.1 extended this with _DSD (Device Specific Data) which made it possible to name the GPIOs among other things. diff --git a/Documentation/acpi/gpio-properties.txt b/Documentation/acpi/gpio-properties.txt index ae36fcf..f35dad1 100644 --- a/Documentation/acpi/gpio-properties.txt +++ b/Documentation/acpi/gpio-properties.txt @@ -1,9 +1,9 @@ _DSD Device Properties Related to GPIO -------------------------------------- -With the release of ACPI 5.1 and the _DSD configuration objecte names -can finally be given to GPIOs (and other things as well) returned by -_CRS. Previously, we were only able to use an integer index to find +With the release of ACPI 5.1, the _DSD configuration object finally +allows names to be given to GPIOs (and other things as well) returned +by _CRS. Previously, we were only able to use an integer index to find the corresponding GPIO, which is pretty error prone (it depends on the _CRS output ordering, for example). diff --git a/Documentation/devicetree/bindings/arm/omap/l3-noc.txt b/Documentation/devicetree/bindings/arm/omap/l3-noc.txt index 974624e..161448d 100644 --- a/Documentation/devicetree/bindings/arm/omap/l3-noc.txt +++ b/Documentation/devicetree/bindings/arm/omap/l3-noc.txt @@ -6,6 +6,7 @@ provided by Arteris. Required properties: - compatible : Should be "ti,omap3-l3-smx" for OMAP3 family Should be "ti,omap4-l3-noc" for OMAP4 family + Should be "ti,omap5-l3-noc" for OMAP5 family Should be "ti,dra7-l3-noc" for DRA7 family Should be "ti,am4372-l3-noc" for AM43 family - reg: Contains L3 register address range for each noc domain. diff --git a/Documentation/devicetree/bindings/clock/silabs,si5351.txt b/Documentation/devicetree/bindings/clock/silabs,si5351.txt index c40711e..28b2830 100644 --- a/Documentation/devicetree/bindings/clock/silabs,si5351.txt +++ b/Documentation/devicetree/bindings/clock/silabs,si5351.txt @@ -17,7 +17,8 @@ Required properties: - #clock-cells: from common clock binding; shall be set to 1. - clocks: from common clock binding; list of parent clock handles, shall be xtal reference clock or xtal and clkin for - si5351c only. + si5351c only. Corresponding clock input names are "xtal" and + "clkin" respectively. - #address-cells: shall be set to 1. - #size-cells: shall be set to 0. @@ -71,6 +72,7 @@ i2c-master-node { /* connect xtal input to 25MHz reference */ clocks = <&ref25>; + clock-names = "xtal"; /* connect xtal input as source of pll0 and pll1 */ silabs,pll-source = <0 0>, <1 0>; diff --git a/Documentation/devicetree/bindings/dma/fsl-mxs-dma.txt b/Documentation/devicetree/bindings/dma/fsl-mxs-dma.txt index a4873e5..e30e184 100644 --- a/Documentation/devicetree/bindings/dma/fsl-mxs-dma.txt +++ b/Documentation/devicetree/bindings/dma/fsl-mxs-dma.txt @@ -38,7 +38,7 @@ dma_apbx: dma-apbx@80024000 { 80 81 68 69 70 71 72 73 74 75 76 77>; - interrupt-names = "auart4-rx", "aurat4-tx", "spdif-tx", "empty", + interrupt-names = "auart4-rx", "auart4-tx", "spdif-tx", "empty", "saif0", "saif1", "i2c0", "i2c1", "auart0-rx", "auart0-tx", "auart1-rx", "auart1-tx", "auart2-rx", "auart2-tx", "auart3-rx", "auart3-tx"; diff --git a/Documentation/devicetree/bindings/input/touchscreen/tsc2005.txt b/Documentation/devicetree/bindings/input/touchscreen/tsc2005.txt index 4b641c7..09089a6 100644 --- a/Documentation/devicetree/bindings/input/touchscreen/tsc2005.txt +++ b/Documentation/devicetree/bindings/input/touchscreen/tsc2005.txt @@ -32,8 +32,8 @@ Example: touchscreen-fuzz-x = <4>; touchscreen-fuzz-y = <7>; touchscreen-fuzz-pressure = <2>; - touchscreen-max-x = <4096>; - touchscreen-max-y = <4096>; + touchscreen-size-x = <4096>; + touchscreen-size-y = <4096>; touchscreen-max-pressure = <2048>; ti,x-plate-ohms = <280>; diff --git a/Documentation/devicetree/bindings/iommu/arm,smmu-v3.txt b/Documentation/devicetree/bindings/iommu/arm,smmu-v3.txt new file mode 100644 index 0000000..c03eec1 --- /dev/null +++ b/Documentation/devicetree/bindings/iommu/arm,smmu-v3.txt @@ -0,0 +1,37 @@ +* ARM SMMUv3 Architecture Implementation + +The SMMUv3 architecture is a significant deparature from previous +revisions, replacing the MMIO register interface with in-memory command +and event queues and adding support for the ATS and PRI components of +the PCIe specification. + +** SMMUv3 required properties: + +- compatible : Should include: + + * "arm,smmu-v3" for any SMMUv3 compliant + implementation. This entry should be last in the + compatible list. + +- reg : Base address and size of the SMMU. + +- interrupts : Non-secure interrupt list describing the wired + interrupt sources corresponding to entries in + interrupt-names. If no wired interrupts are + present then this property may be omitted. + +- interrupt-names : When the interrupts property is present, should + include the following: + * "eventq" - Event Queue not empty + * "priq" - PRI Queue not empty + * "cmdq-sync" - CMD_SYNC complete + * "gerror" - Global Error activated + +** SMMUv3 optional properties: + +- dma-coherent : Present if DMA operations made by the SMMU (page + table walks, stream table accesses etc) are cache + coherent with the CPU. + + NOTE: this only applies to the SMMU itself, not + masters connected upstream of the SMMU. diff --git a/Documentation/devicetree/bindings/mtd/m25p80.txt b/Documentation/devicetree/bindings/mtd/jedec,spi-nor.txt index f20b111..2bee681 100644 --- a/Documentation/devicetree/bindings/mtd/m25p80.txt +++ b/Documentation/devicetree/bindings/mtd/jedec,spi-nor.txt @@ -8,8 +8,8 @@ Required properties: is not Linux-only, but in case of Linux, see the "m25p_ids" table in drivers/mtd/devices/m25p80.c for the list of supported chips. - Must also include "nor-jedec" for any SPI NOR flash that can be - identified by the JEDEC READ ID opcode (0x9F). + Must also include "jedec,spi-nor" for any SPI NOR flash that can + be identified by the JEDEC READ ID opcode (0x9F). - reg : Chip-Select number - spi-max-frequency : Maximum frequency of the SPI bus the chip can operate at @@ -25,7 +25,7 @@ Example: flash: m25p80@0 { #address-cells = <1>; #size-cells = <1>; - compatible = "spansion,m25p80", "nor-jedec"; + compatible = "spansion,m25p80", "jedec,spi-nor"; reg = <0>; spi-max-frequency = <40000000>; m25p,fast-read; diff --git a/Documentation/devicetree/bindings/net/cdns-emac.txt b/Documentation/devicetree/bindings/net/cdns-emac.txt index abd67c1..4451ee97 100644 --- a/Documentation/devicetree/bindings/net/cdns-emac.txt +++ b/Documentation/devicetree/bindings/net/cdns-emac.txt @@ -3,7 +3,8 @@ Required properties: - compatible: Should be "cdns,[<chip>-]{emac}" Use "cdns,at91rm9200-emac" Atmel at91rm9200 SoC. - or the generic form: "cdns,emac". + Use "cdns,zynq-gem" Xilinx Zynq-7xxx SoC. + Or the generic form: "cdns,emac". - reg: Address and length of the register set for the device - interrupts: Should contain macb interrupt - phy-mode: see ethernet.txt file in the same directory. diff --git a/Documentation/devicetree/bindings/rtc/abracon,abx80x.txt b/Documentation/devicetree/bindings/rtc/abracon,abx80x.txt new file mode 100644 index 0000000..be78968 --- /dev/null +++ b/Documentation/devicetree/bindings/rtc/abracon,abx80x.txt @@ -0,0 +1,30 @@ +Abracon ABX80X I2C ultra low power RTC/Alarm chip + +The Abracon ABX80X family consist of the ab0801, ab0803, ab0804, ab0805, ab1801, +ab1803, ab1804 and ab1805. The ab0805 is the superset of ab080x and the ab1805 +is the superset of ab180x. + +Required properties: + + - "compatible": should one of: + "abracon,abx80x" + "abracon,ab0801" + "abracon,ab0803" + "abracon,ab0804" + "abracon,ab0805" + "abracon,ab1801" + "abracon,ab1803" + "abracon,ab1804" + "abracon,ab1805" + Using "abracon,abx80x" will enable chip autodetection. + - "reg": I2C bus address of the device + +Optional properties: + +The abx804 and abx805 have a trickle charger that is able to charge the +connected battery or supercap. Both the following properties have to be defined +and valid to enable charging: + + - "abracon,tc-diode": should be "standard" (0.6V) or "schottky" (0.3V) + - "abracon,tc-resistor": should be <0>, <3>, <6> or <11>. 0 disables the output + resistor, the other values are in ohm. diff --git a/Documentation/devicetree/bindings/usb/renesas_usbhs.txt b/Documentation/devicetree/bindings/usb/renesas_usbhs.txt index dc2a18f..ddbe304 100644 --- a/Documentation/devicetree/bindings/usb/renesas_usbhs.txt +++ b/Documentation/devicetree/bindings/usb/renesas_usbhs.txt @@ -15,10 +15,8 @@ Optional properties: - phys: phandle + phy specifier pair - phy-names: must be "usb" - dmas: Must contain a list of references to DMA specifiers. - - dma-names : Must contain a list of DMA names: - - tx0 ... tx<n> - - rx0 ... rx<n> - - This <n> means DnFIFO in USBHS module. + - dma-names : named "ch%d", where %d is the channel number ranging from zero + to the number of channels (DnFIFOs) minus one. Example: usbhs: usb@e6590000 { diff --git a/Documentation/hwmon/tmp401 b/Documentation/hwmon/tmp401 index 8eb88e9..711f75e 100644 --- a/Documentation/hwmon/tmp401 +++ b/Documentation/hwmon/tmp401 @@ -20,7 +20,7 @@ Supported chips: Datasheet: http://focus.ti.com/docs/prod/folders/print/tmp432.html * Texas Instruments TMP435 Prefix: 'tmp435' - Addresses scanned: I2C 0x37, 0x48 - 0x4f + Addresses scanned: I2C 0x48 - 0x4f Datasheet: http://focus.ti.com/docs/prod/folders/print/tmp435.html Authors: diff --git a/Documentation/kasan.txt b/Documentation/kasan.txt index 092fc10..4692241 100644 --- a/Documentation/kasan.txt +++ b/Documentation/kasan.txt @@ -9,7 +9,9 @@ a fast and comprehensive solution for finding use-after-free and out-of-bounds bugs. KASan uses compile-time instrumentation for checking every memory access, -therefore you will need a certain version of GCC > 4.9.2 +therefore you will need a gcc version of 4.9.2 or later. KASan could detect out +of bounds accesses to stack or global variables, but only if gcc 5.0 or later was +used to built the kernel. Currently KASan is supported only for x86_64 architecture and requires that the kernel be built with the SLUB allocator. @@ -23,8 +25,8 @@ To enable KASAN configure kernel with: and choose between CONFIG_KASAN_OUTLINE and CONFIG_KASAN_INLINE. Outline/inline is compiler instrumentation types. The former produces smaller binary the -latter is 1.1 - 2 times faster. Inline instrumentation requires GCC 5.0 or -latter. +latter is 1.1 - 2 times faster. Inline instrumentation requires a gcc version +of 5.0 or later. Currently KASAN works only with the SLUB memory allocator. For better bug detection and nicer report, enable CONFIG_STACKTRACE and put diff --git a/Documentation/kernel-parameters.txt b/Documentation/kernel-parameters.txt index 61ab162..6726139 100644 --- a/Documentation/kernel-parameters.txt +++ b/Documentation/kernel-parameters.txt @@ -1481,6 +1481,12 @@ bytes respectively. Such letter suffixes can also be entirely omitted. By default, super page will be supported if Intel IOMMU has the capability. With this option, super page will not be supported. + ecs_off [Default Off] + By default, extended context tables will be supported if + the hardware advertises that it has support both for the + extended tables themselves, and also PASID support. With + this option set, extended tables will not be used even + on hardware which claims to support them. intel_idle.max_cstate= [KNL,HW,ACPI,X86] 0 disables intel_idle and fall back on acpi_idle. diff --git a/Documentation/networking/udplite.txt b/Documentation/networking/udplite.txt index d727a38..53a7268 100644 --- a/Documentation/networking/udplite.txt +++ b/Documentation/networking/udplite.txt @@ -20,7 +20,7 @@ files/UDP-Lite-HOWTO.txt o The Wireshark UDP-Lite WiKi (with capture files): - http://wiki.wireshark.org/Lightweight_User_Datagram_Protocol + https://wiki.wireshark.org/Lightweight_User_Datagram_Protocol o The Protocol Spec, RFC 3828, http://www.ietf.org/rfc/rfc3828.txt diff --git a/Documentation/serial/tty.txt b/Documentation/serial/tty.txt index 1e52d67..dbe6623 100644 --- a/Documentation/serial/tty.txt +++ b/Documentation/serial/tty.txt @@ -198,6 +198,9 @@ TTY_IO_ERROR If set, causes all subsequent userspace read/write TTY_OTHER_CLOSED Device is a pty and the other side has closed. +TTY_OTHER_DONE Device is a pty and the other side has closed and + all pending input processing has been completed. + TTY_NO_WRITE_SPLIT Prevent driver from splitting up writes into smaller chunks. diff --git a/Documentation/target/tcmu-design.txt b/Documentation/target/tcmu-design.txt index 43e94ea..263b907 100644 --- a/Documentation/target/tcmu-design.txt +++ b/Documentation/target/tcmu-design.txt @@ -15,8 +15,7 @@ Contents: a) Discovering and configuring TCMU uio devices b) Waiting for events on the device(s) c) Managing the command ring -3) Command filtering and pass_level -4) A final note +3) A final note TCM Userspace Design @@ -324,7 +323,7 @@ int handle_device_events(int fd, void *map) /* Process events from cmd ring until we catch up with cmd_head */ while (ent != (void *)mb + mb->cmdr_off + mb->cmd_head) { - if (tcmu_hdr_get_op(&ent->hdr) == TCMU_OP_CMD) { + if (tcmu_hdr_get_op(ent->hdr.len_op) == TCMU_OP_CMD) { uint8_t *cdb = (void *)mb + ent->req.cdb_off; bool success = true; @@ -339,8 +338,12 @@ int handle_device_events(int fd, void *map) ent->rsp.scsi_status = SCSI_CHECK_CONDITION; } } + else if (tcmu_hdr_get_op(ent->hdr.len_op) != TCMU_OP_PAD) { + /* Tell the kernel we didn't handle unknown opcodes */ + ent->hdr.uflags |= TCMU_UFLAG_UNKNOWN_OP; + } else { - /* Do nothing for PAD entries */ + /* Do nothing for PAD entries except update cmd_tail */ } /* update cmd_tail */ @@ -360,28 +363,6 @@ int handle_device_events(int fd, void *map) } -Command filtering and pass_level --------------------------------- - -TCMU supports a "pass_level" option with valid values of 0 or 1. When -the value is 0 (the default), nearly all SCSI commands received for -the device are passed through to the handler. This allows maximum -flexibility but increases the amount of code required by the handler, -to support all mandatory SCSI commands. If pass_level is set to 1, -then only IO-related commands are presented, and the rest are handled -by LIO's in-kernel command emulation. The commands presented at level -1 include all versions of: - -READ -WRITE -WRITE_VERIFY -XDWRITEREAD -WRITE_SAME -COMPARE_AND_WRITE -SYNCHRONIZE_CACHE -UNMAP - - A final note ------------ diff --git a/Documentation/virtual/kvm/mmu.txt b/Documentation/virtual/kvm/mmu.txt index 53838d9..c59bd9b 100644 --- a/Documentation/virtual/kvm/mmu.txt +++ b/Documentation/virtual/kvm/mmu.txt @@ -169,6 +169,10 @@ Shadow pages contain the following information: Contains the value of cr4.smep && !cr0.wp for which the page is valid (pages for which this is true are different from other pages; see the treatment of cr0.wp=0 below). + role.smap_andnot_wp: + Contains the value of cr4.smap && !cr0.wp for which the page is valid + (pages for which this is true are different from other pages; see the + treatment of cr0.wp=0 below). gfn: Either the guest page table containing the translations shadowed by this page, or the base page frame for linear translations. See role.direct. @@ -344,10 +348,16 @@ on fault type: (user write faults generate a #PF) -In the first case there is an additional complication if CR4.SMEP is -enabled: since we've turned the page into a kernel page, the kernel may now -execute it. We handle this by also setting spte.nx. If we get a user -fetch or read fault, we'll change spte.u=1 and spte.nx=gpte.nx back. +In the first case there are two additional complications: +- if CR4.SMEP is enabled: since we've turned the page into a kernel page, + the kernel may now execute it. We handle this by also setting spte.nx. + If we get a user fetch or read fault, we'll change spte.u=1 and + spte.nx=gpte.nx back. +- if CR4.SMAP is disabled: since the page has been changed to a kernel + page, it can not be reused when CR4.SMAP is enabled. We set + CR4.SMAP && !CR0.WP into shadow page's role to avoid this case. Note, + here we do not care the case that CR4.SMAP is enabled since KVM will + directly inject #PF to guest due to failed permission check. To prevent an spte that was converted into a kernel page with cr0.wp=0 from being written by the kernel after cr0.wp has changed to 1, we make |