diff options
Diffstat (limited to 'Documentation')
| -rw-r--r-- | Documentation/ABI/testing/sysfs-devices-system-cpu | 24 | ||||
| -rw-r--r-- | Documentation/cpu-freq/boost.txt | 26 | ||||
| -rw-r--r-- | Documentation/cpu-freq/intel-pstate.txt | 40 |
3 files changed, 77 insertions, 13 deletions
diff --git a/Documentation/ABI/testing/sysfs-devices-system-cpu b/Documentation/ABI/testing/sysfs-devices-system-cpu index 468e4d4..d5a0d33 100644 --- a/Documentation/ABI/testing/sysfs-devices-system-cpu +++ b/Documentation/ABI/testing/sysfs-devices-system-cpu @@ -200,3 +200,27 @@ Description: address and size of the percpu note. note of cpu#. crash_notes_size: size of the note of cpu#. + + +What: /sys/devices/system/cpu/intel_pstate/max_perf_pct + /sys/devices/system/cpu/intel_pstate/min_perf_pct + /sys/devices/system/cpu/intel_pstate/no_turbo +Date: February 2013 +Contact: linux-pm@vger.kernel.org +Description: Parameters for the Intel P-state driver + + Logic for selecting the current P-state in Intel + Sandybridge+ processors. The three knobs control + limits for the P-state that will be requested by the + driver. + + max_perf_pct: limits the maximum P state that will be requested by + the driver stated as a percentage of the available performance. + + min_perf_pct: limits the minimum P state that will be requested by + the driver stated as a percentage of the available performance. + + no_turbo: limits the driver to selecting P states below the turbo + frequency range. + + More details can be found in Documentation/cpu-freq/intel-pstate.txt diff --git a/Documentation/cpu-freq/boost.txt b/Documentation/cpu-freq/boost.txt index 9b4edfc..dd62e13 100644 --- a/Documentation/cpu-freq/boost.txt +++ b/Documentation/cpu-freq/boost.txt @@ -17,8 +17,8 @@ Introduction Some CPUs support a functionality to raise the operating frequency of some cores in a multi-core package if certain conditions apply, mostly if the whole chip is not fully utilized and below it's intended thermal -budget. This is done without operating system control by a combination -of hardware and firmware. +budget. The decision about boost disable/enable is made either at hardware +(e.g. x86) or software (e.g ARM). On Intel CPUs this is called "Turbo Boost", AMD calls it "Turbo-Core", in technical documentation "Core performance boost". In Linux we use the term "boost" for convenience. @@ -48,24 +48,24 @@ be desirable: User controlled switch ---------------------- -To allow the user to toggle the boosting functionality, the acpi-cpufreq -driver exports a sysfs knob to disable it. There is a file: +To allow the user to toggle the boosting functionality, the cpufreq core +driver exports a sysfs knob to enable or disable it. There is a file: /sys/devices/system/cpu/cpufreq/boost which can either read "0" (boosting disabled) or "1" (boosting enabled). -Reading the file is always supported, even if the processor does not -support boosting. In this case the file will be read-only and always -reads as "0". Explicitly changing the permissions and writing to that -file anyway will return EINVAL. +The file is exported only when cpufreq driver supports boosting. +Explicitly changing the permissions and writing to that file anyway will +return EINVAL. On supported CPUs one can write either a "0" or a "1" into this file. This will either disable the boost functionality on all cores in the -whole system (0) or will allow the hardware to boost at will (1). +whole system (0) or will allow the software or hardware to boost at will +(1). Writing a "1" does not explicitly boost the system, but just allows the -CPU (and the firmware) to boost at their discretion. Some implementations -take external factors like the chip's temperature into account, so -boosting once does not necessarily mean that it will occur every time -even using the exact same software setup. +CPU to boost at their discretion. Some implementations take external +factors like the chip's temperature into account, so boosting once does +not necessarily mean that it will occur every time even using the exact +same software setup. AMD legacy cpb switch diff --git a/Documentation/cpu-freq/intel-pstate.txt b/Documentation/cpu-freq/intel-pstate.txt new file mode 100644 index 0000000..e742d21 --- /dev/null +++ b/Documentation/cpu-freq/intel-pstate.txt @@ -0,0 +1,40 @@ +Intel P-state driver +-------------------- + +This driver implements a scaling driver with an internal governor for +Intel Core processors. The driver follows the same model as the +Transmeta scaling driver (longrun.c) and implements the setpolicy() +instead of target(). Scaling drivers that implement setpolicy() are +assumed to implement internal governors by the cpufreq core. All the +logic for selecting the current P state is contained within the +driver; no external governor is used by the cpufreq core. + +Intel SandyBridge+ processors are supported. + +New sysfs files for controlling P state selection have been added to +/sys/devices/system/cpu/intel_pstate/ + + max_perf_pct: limits the maximum P state that will be requested by + the driver stated as a percentage of the available performance. + + min_perf_pct: limits the minimum P state that will be requested by + the driver stated as a percentage of the available performance. + + no_turbo: limits the driver to selecting P states below the turbo + frequency range. + +For contemporary Intel processors, the frequency is controlled by the +processor itself and the P-states exposed to software are related to +performance levels. The idea that frequency can be set to a single +frequency is fiction for Intel Core processors. Even if the scaling +driver selects a single P state the actual frequency the processor +will run at is selected by the processor itself. + +New debugfs files have also been added to /sys/kernel/debug/pstate_snb/ + + deadband + d_gain_pct + i_gain_pct + p_gain_pct + sample_rate_ms + setpoint |