diff options
Diffstat (limited to 'Documentation')
8 files changed, 166 insertions, 20 deletions
diff --git a/Documentation/devicetree/bindings/arm/freescale/fsl,vf610-mscm-cpucfg.txt b/Documentation/devicetree/bindings/arm/freescale/fsl,vf610-mscm-cpucfg.txt new file mode 100644 index 0000000..44aa3c4 --- /dev/null +++ b/Documentation/devicetree/bindings/arm/freescale/fsl,vf610-mscm-cpucfg.txt @@ -0,0 +1,14 @@ +Freescale Vybrid Miscellaneous System Control - CPU Configuration + +The MSCM IP contains multiple sub modules, this binding describes the first +block of registers which contains CPU configuration information. + +Required properties: +- compatible: "fsl,vf610-mscm-cpucfg", "syscon" +- reg: the register range of the MSCM CPU configuration registers + +Example: + mscm_cpucfg: cpucfg@40001000 { + compatible = "fsl,vf610-mscm-cpucfg", "syscon"; + reg = <0x40001000 0x800>; + } diff --git a/Documentation/devicetree/bindings/arm/freescale/fsl,vf610-mscm-ir.txt b/Documentation/devicetree/bindings/arm/freescale/fsl,vf610-mscm-ir.txt new file mode 100644 index 0000000..669808b2a --- /dev/null +++ b/Documentation/devicetree/bindings/arm/freescale/fsl,vf610-mscm-ir.txt @@ -0,0 +1,33 @@ +Freescale Vybrid Miscellaneous System Control - Interrupt Router + +The MSCM IP contains multiple sub modules, this binding describes the second +block of registers which control the interrupt router. The interrupt router +allows to configure the recipient of each peripheral interrupt. Furthermore +it controls the directed processor interrupts. The module is available in all +Vybrid SoC's but is only really useful in dual core configurations (VF6xx +which comes with a Cortex-A5/Cortex-M4 combination). + +Required properties: +- compatible: "fsl,vf610-mscm-ir" +- reg: the register range of the MSCM Interrupt Router +- fsl,cpucfg: The handle to the MSCM CPU configuration node, required + to get the current CPU ID +- interrupt-controller: Identifies the node as an interrupt controller +- #interrupt-cells: Two cells, interrupt number and cells. + The hardware interrupt number according to interrupt + assignment of the interrupt router is required. + Flags get passed only when using GIC as parent. Flags + encoding as documented by the GIC bindings. +- interrupt-parent: Should be the phandle for the interrupt controller of + the CPU the device tree is intended to be used on. This + is either the node of the GIC or NVIC controller. + +Example: + mscm_ir: interrupt-controller@40001800 { + compatible = "fsl,vf610-mscm-ir"; + reg = <0x40001800 0x400>; + fsl,cpucfg = <&mscm_cpucfg>; + interrupt-controller; + #interrupt-cells = <2>; + interrupt-parent = <&intc>; + } diff --git a/Documentation/devicetree/bindings/arm/gic.txt b/Documentation/devicetree/bindings/arm/gic.txt index c97484b..1e0d212 100644 --- a/Documentation/devicetree/bindings/arm/gic.txt +++ b/Documentation/devicetree/bindings/arm/gic.txt @@ -56,11 +56,6 @@ Optional regions, used when the GIC doesn't have banked registers. The offset is cpu-offset * cpu-nr. -- arm,routable-irqs : Total number of gic irq inputs which are not directly - connected from the peripherals, but are routed dynamically - by a crossbar/multiplexer preceding the GIC. The GIC irq - input line is assigned dynamically when the corresponding - peripheral's crossbar line is mapped. Example: intc: interrupt-controller@fff11000 { @@ -68,7 +63,6 @@ Example: #interrupt-cells = <3>; #address-cells = <1>; interrupt-controller; - arm,routable-irqs = <160>; reg = <0xfff11000 0x1000>, <0xfff10100 0x100>; }; diff --git a/Documentation/devicetree/bindings/arm/omap/crossbar.txt b/Documentation/devicetree/bindings/arm/omap/crossbar.txt index 4139db3..a9b28d7 100644 --- a/Documentation/devicetree/bindings/arm/omap/crossbar.txt +++ b/Documentation/devicetree/bindings/arm/omap/crossbar.txt @@ -9,7 +9,9 @@ inputs. Required properties: - compatible : Should be "ti,irq-crossbar" - reg: Base address and the size of the crossbar registers. -- ti,max-irqs: Total number of irqs available at the interrupt controller. +- interrupt-controller: indicates that this block is an interrupt controller. +- interrupt-parent: the interrupt controller this block is connected to. +- ti,max-irqs: Total number of irqs available at the parent interrupt controller. - ti,max-crossbar-sources: Maximum number of crossbar sources that can be routed. - ti,reg-size: Size of a individual register in bytes. Every individual register is assumed to be of same size. Valid sizes are 1, 2, 4. @@ -27,13 +29,13 @@ Optional properties: when the interrupt controller irq is unused (when not provided, default is 0) Examples: - crossbar_mpu: @4a020000 { + crossbar_mpu: crossbar@4a002a48 { compatible = "ti,irq-crossbar"; reg = <0x4a002a48 0x130>; ti,max-irqs = <160>; ti,max-crossbar-sources = <400>; ti,reg-size = <2>; - ti,irqs-reserved = <0 1 2 3 5 6 131 132 139 140>; + ti,irqs-reserved = <0 1 2 3 5 6 131 132>; ti,irqs-skip = <10 133 139 140>; }; @@ -44,10 +46,6 @@ Documentation/devicetree/bindings/arm/gic.txt for further details. An interrupt consumer on an SoC using crossbar will use: interrupts = <GIC_SPI request_number interrupt_level> -When the request number is between 0 to that described by -"ti,max-crossbar-sources", it is assumed to be a crossbar mapping. If the -request_number is greater than "ti,max-crossbar-sources", then it is mapped as a -quirky hardware mapping direct to GIC. Example: device_x@0x4a023000 { @@ -55,9 +53,3 @@ Example: interrupts = <GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH>; ... }; - - device_y@0x4a033000 { - /* Direct mapped GIC SPI 1 used */ - interrupts = <GIC_SPI DIRECT_IRQ(1) IRQ_TYPE_LEVEL_HIGH>; - ... - }; diff --git a/Documentation/devicetree/bindings/interrupt-controller/nvidia,tegra-ictlr.txt b/Documentation/devicetree/bindings/interrupt-controller/nvidia,tegra-ictlr.txt new file mode 100644 index 0000000..1099fe0 --- /dev/null +++ b/Documentation/devicetree/bindings/interrupt-controller/nvidia,tegra-ictlr.txt @@ -0,0 +1,43 @@ +NVIDIA Legacy Interrupt Controller + +All Tegra SoCs contain a legacy interrupt controller that routes +interrupts to the GIC, and also serves as a wakeup source. It is also +referred to as "ictlr", hence the name of the binding. + +The HW block exposes a number of interrupt controllers, each +implementing a set of 32 interrupts. + +Required properties: + +- compatible : should be: "nvidia,tegra<chip>-ictlr". The LIC on + subsequent SoCs remained backwards-compatible with Tegra30, so on + Tegra generations later than Tegra30 the compatible value should + include "nvidia,tegra30-ictlr". +- reg : Specifies base physical address and size of the registers. + Each controller must be described separately (Tegra20 has 4 of them, + whereas Tegra30 and later have 5" +- interrupt-controller : Identifies the node as an interrupt controller. +- #interrupt-cells : Specifies the number of cells needed to encode an + interrupt source. The value must be 3. +- interrupt-parent : a phandle to the GIC these interrupts are routed + to. + +Notes: + +- Because this HW ultimately routes interrupts to the GIC, the + interrupt specifier must be that of the GIC. +- Only SPIs can use the ictlr as an interrupt parent. SGIs and PPIs + are explicitly forbidden. + +Example: + + ictlr: interrupt-controller@60004000 { + compatible = "nvidia,tegra20-ictlr", "nvidia,tegra-ictlr"; + reg = <0x60004000 64>, + <0x60004100 64>, + <0x60004200 64>, + <0x60004300 64>; + interrupt-controller; + #interrupt-cells = <3>; + interrupt-parent = <&intc>; + }; diff --git a/Documentation/devicetree/bindings/interrupt-controller/renesas,irqc.txt b/Documentation/devicetree/bindings/interrupt-controller/renesas,irqc.txt index 1a88e62..63633bd 100644 --- a/Documentation/devicetree/bindings/interrupt-controller/renesas,irqc.txt +++ b/Documentation/devicetree/bindings/interrupt-controller/renesas,irqc.txt @@ -4,7 +4,7 @@ Required properties: - compatible: has to be "renesas,irqc-<soctype>", "renesas,irqc" as fallback. Examples with soctypes are: - - "renesas,irqc-r8a73a4" (R-Mobile AP6) + - "renesas,irqc-r8a73a4" (R-Mobile APE6) - "renesas,irqc-r8a7790" (R-Car H2) - "renesas,irqc-r8a7791" (R-Car M2-W) - "renesas,irqc-r8a7792" (R-Car V2H) @@ -12,6 +12,7 @@ Required properties: - "renesas,irqc-r8a7794" (R-Car E2) - #interrupt-cells: has to be <2>: an interrupt index and flags, as defined in interrupts.txt in this directory +- clocks: Must contain a reference to the functional clock. Optional properties: @@ -29,4 +30,5 @@ Example: <0 1 IRQ_TYPE_LEVEL_HIGH>, <0 2 IRQ_TYPE_LEVEL_HIGH>, <0 3 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&mstp4_clks R8A7790_CLK_IRQC>; }; diff --git a/Documentation/devicetree/bindings/interrupt-controller/st,sti-irq-syscfg.txt b/Documentation/devicetree/bindings/interrupt-controller/st,sti-irq-syscfg.txt new file mode 100644 index 0000000..ced6014 --- /dev/null +++ b/Documentation/devicetree/bindings/interrupt-controller/st,sti-irq-syscfg.txt @@ -0,0 +1,35 @@ +STMicroelectronics STi System Configuration Controlled IRQs +----------------------------------------------------------- + +On STi based systems; External, CTI (Core Sight), PMU (Performance Management), +and PL310 L2 Cache IRQs are controlled using System Configuration registers. +This driver is used to unmask them prior to use. + +Required properties: +- compatible : Should be set to one of: + "st,stih415-irq-syscfg" + "st,stih416-irq-syscfg" + "st,stih407-irq-syscfg" + "st,stid127-irq-syscfg" +- st,syscfg : Phandle to Cortex-A9 IRQ system config registers +- st,irq-device : Array of IRQs to enable - should be 2 in length +- st,fiq-device : Array of FIQs to enable - should be 2 in length + +Optional properties: +- st,invert-ext : External IRQs can be inverted at will. This property inverts + these IRQs using bitwise logic. A number of defines have been + provided for convenience: + ST_IRQ_SYSCFG_EXT_1_INV + ST_IRQ_SYSCFG_EXT_2_INV + ST_IRQ_SYSCFG_EXT_3_INV +Example: + +irq-syscfg { + compatible = "st,stih416-irq-syscfg"; + st,syscfg = <&syscfg_cpu>; + st,irq-device = <ST_IRQ_SYSCFG_PMU_0>, + <ST_IRQ_SYSCFG_PMU_1>; + st,fiq-device = <ST_IRQ_SYSCFG_DISABLED>, + <ST_IRQ_SYSCFG_DISABLED>; + st,invert-ext = <(ST_IRQ_SYSCFG_EXT_1_INV | ST_IRQ_SYSCFG_EXT_3_INV)>; +}; diff --git a/Documentation/devicetree/bindings/interrupt-controller/ti,omap4-wugen-mpu b/Documentation/devicetree/bindings/interrupt-controller/ti,omap4-wugen-mpu new file mode 100644 index 0000000..43effa0 --- /dev/null +++ b/Documentation/devicetree/bindings/interrupt-controller/ti,omap4-wugen-mpu @@ -0,0 +1,33 @@ +TI OMAP4 Wake-up Generator + +All TI OMAP4/5 (and their derivatives) an interrupt controller that +routes interrupts to the GIC, and also serves as a wakeup source. It +is also referred to as "WUGEN-MPU", hence the name of the binding. + +Reguired properties: + +- compatible : should contain at least "ti,omap4-wugen-mpu" or + "ti,omap5-wugen-mpu" +- reg : Specifies base physical address and size of the registers. +- interrupt-controller : Identifies the node as an interrupt controller. +- #interrupt-cells : Specifies the number of cells needed to encode an + interrupt source. The value must be 3. +- interrupt-parent : a phandle to the GIC these interrupts are routed + to. + +Notes: + +- Because this HW ultimately routes interrupts to the GIC, the + interrupt specifier must be that of the GIC. +- Only SPIs can use the WUGEN as an interrupt parent. SGIs and PPIs + are explicitly forbiden. + +Example: + + wakeupgen: interrupt-controller@48281000 { + compatible = "ti,omap5-wugen-mpu", "ti,omap4-wugen-mpu"; + interrupt-controller; + #interrupt-cells = <3>; + reg = <0x48281000 0x1000>; + interrupt-parent = <&gic>; + }; |