summaryrefslogtreecommitdiff
path: root/arch/arm/boot/dts
diff options
context:
space:
mode:
Diffstat (limited to 'arch/arm/boot/dts')
-rw-r--r--arch/arm/boot/dts/Makefile1
-rw-r--r--arch/arm/boot/dts/am335x-boneblack.dts11
-rw-r--r--arch/arm/boot/dts/am33xx.dtsi88
-rw-r--r--arch/arm/boot/dts/am57xx-beagle-x15-common.dtsi596
-rw-r--r--arch/arm/boot/dts/am57xx-beagle-x15-revb1.dts24
-rw-r--r--arch/arm/boot/dts/am57xx-beagle-x15.dts812
-rw-r--r--arch/arm/boot/dts/dra7.dtsi26
-rw-r--r--arch/arm/boot/dts/dra74x.dtsi1
-rw-r--r--arch/arm/boot/dts/omap3-gta04.dtsi2
-rw-r--r--arch/arm/boot/dts/omap4-panda-common.dtsi2
-rw-r--r--arch/arm/boot/dts/omap5-board-common.dtsi29
-rw-r--r--arch/arm/boot/dts/omap5-cm-t54.dts2
-rw-r--r--arch/arm/boot/dts/omap5-igep0050.dts40
-rw-r--r--arch/arm/boot/dts/omap5-uevm.dts16
-rw-r--r--arch/arm/boot/dts/omap5.dtsi24
15 files changed, 731 insertions, 943 deletions
diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index 2fcd6a1..cf989f2 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -584,6 +584,7 @@ dtb-$(CONFIG_SOC_OMAP5) += \
omap5-uevm.dtb
dtb-$(CONFIG_SOC_DRA7XX) += \
am57xx-beagle-x15.dtb \
+ am57xx-beagle-x15-revb1.dtb \
am57xx-cl-som-am57x.dtb \
am57xx-sbc-am57x.dtb \
am572x-idk.dtb \
diff --git a/arch/arm/boot/dts/am335x-boneblack.dts b/arch/arm/boot/dts/am335x-boneblack.dts
index ca72167..55c0e95 100644
--- a/arch/arm/boot/dts/am335x-boneblack.dts
+++ b/arch/arm/boot/dts/am335x-boneblack.dts
@@ -33,17 +33,6 @@
status = "okay";
};
-&cpu0_opp_table {
- /*
- * All PG 2.0 silicon may not support 1GHz but some of the early
- * BeagleBone Blacks have PG 2.0 silicon which is guaranteed
- * to support 1GHz OPP so enable it for PG 2.0 on this board.
- */
- oppnitro@1000000000 {
- opp-supported-hw = <0x06 0x0100>;
- };
-};
-
&am33xx_pinmux {
nxp_hdmi_bonelt_pins: nxp_hdmi_bonelt_pins {
pinctrl-single,pins = <
diff --git a/arch/arm/boot/dts/am33xx.dtsi b/arch/arm/boot/dts/am33xx.dtsi
index eeef6bc..194d884 100644
--- a/arch/arm/boot/dts/am33xx.dtsi
+++ b/arch/arm/boot/dts/am33xx.dtsi
@@ -45,9 +45,19 @@
device_type = "cpu";
reg = <0>;
- operating-points-v2 = <&cpu0_opp_table>;
- ti,syscon-efuse = <&scm_conf 0x7fc 0x1fff 0>;
- ti,syscon-rev = <&scm_conf 0x600>;
+ /*
+ * To consider voltage drop between PMIC and SoC,
+ * tolerance value is reduced to 2% from 4% and
+ * voltage value is increased as a precaution.
+ */
+ operating-points = <
+ /* kHz uV */
+ 720000 1285000
+ 600000 1225000
+ 500000 1125000
+ 275000 1125000
+ >;
+ voltage-tolerance = <2>; /* 2 percentage */
clocks = <&dpll_mpu_ck>;
clock-names = "cpu";
@@ -56,78 +66,6 @@
};
};
- cpu0_opp_table: opp_table0 {
- compatible = "operating-points-v2";
-
- /*
- * The three following nodes are marked with opp-suspend
- * because the can not be enabled simultaneously on a
- * single SoC.
- */
- opp50@300000000 {
- opp-hz = /bits/ 64 <300000000>;
- opp-microvolt = <950000 931000 969000>;
- opp-supported-hw = <0x06 0x0010>;
- opp-suspend;
- };
-
- opp100@275000000 {
- opp-hz = /bits/ 64 <275000000>;
- opp-microvolt = <1100000 1078000 1122000>;
- opp-supported-hw = <0x01 0x00FF>;
- opp-suspend;
- };
-
- opp100@300000000 {
- opp-hz = /bits/ 64 <300000000>;
- opp-microvolt = <1100000 1078000 1122000>;
- opp-supported-hw = <0x06 0x0020>;
- opp-suspend;
- };
-
- opp100@500000000 {
- opp-hz = /bits/ 64 <500000000>;
- opp-microvolt = <1100000 1078000 1122000>;
- opp-supported-hw = <0x01 0xFFFF>;
- };
-
- opp100@600000000 {
- opp-hz = /bits/ 64 <600000000>;
- opp-microvolt = <1100000 1078000 1122000>;
- opp-supported-hw = <0x06 0x0040>;
- };
-
- opp120@600000000 {
- opp-hz = /bits/ 64 <600000000>;
- opp-microvolt = <1200000 1176000 1224000>;
- opp-supported-hw = <0x01 0xFFFF>;
- };
-
- opp120@720000000 {
- opp-hz = /bits/ 64 <720000000>;
- opp-microvolt = <1200000 1176000 1224000>;
- opp-supported-hw = <0x06 0x0080>;
- };
-
- oppturbo@720000000 {
- opp-hz = /bits/ 64 <720000000>;
- opp-microvolt = <1260000 1234800 1285200>;
- opp-supported-hw = <0x01 0xFFFF>;
- };
-
- oppturbo@800000000 {
- opp-hz = /bits/ 64 <800000000>;
- opp-microvolt = <1260000 1234800 1285200>;
- opp-supported-hw = <0x06 0x0100>;
- };
-
- oppnitro@1000000000 {
- opp-hz = /bits/ 64 <1000000000>;
- opp-microvolt = <1325000 1298500 1351500>;
- opp-supported-hw = <0x04 0x0200>;
- };
- };
-
pmu {
compatible = "arm,cortex-a8-pmu";
interrupts = <3>;
diff --git a/arch/arm/boot/dts/am57xx-beagle-x15-common.dtsi b/arch/arm/boot/dts/am57xx-beagle-x15-common.dtsi
new file mode 100644
index 0000000..ec85ff9
--- /dev/null
+++ b/arch/arm/boot/dts/am57xx-beagle-x15-common.dtsi
@@ -0,0 +1,596 @@
+/*
+ * Copyright (C) 2014-2016 Texas Instruments Incorporated - http://www.ti.com/
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+/dts-v1/;
+
+#include "dra74x.dtsi"
+#include "am57xx-commercial-grade.dtsi"
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/interrupt-controller/irq.h>
+
+/ {
+ compatible = "ti,am572x-beagle-x15", "ti,am5728", "ti,dra742", "ti,dra74", "ti,dra7";
+
+ aliases {
+ rtc0 = &mcp_rtc;
+ rtc1 = &tps659038_rtc;
+ rtc2 = &rtc;
+ display0 = &hdmi0;
+ };
+
+ memory@0 {
+ device_type = "memory";
+ reg = <0x0 0x80000000 0x0 0x80000000>;
+ };
+
+ vdd_3v3: fixedregulator-vdd_3v3 {
+ compatible = "regulator-fixed";
+ regulator-name = "vdd_3v3";
+ vin-supply = <&regen1>;
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ };
+
+ aic_dvdd: fixedregulator-aic_dvdd {
+ compatible = "regulator-fixed";
+ regulator-name = "aic_dvdd_fixed";
+ vin-supply = <&vdd_3v3>;
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ };
+
+ vtt_fixed: fixedregulator-vtt {
+ /* TPS51200 */
+ compatible = "regulator-fixed";
+ regulator-name = "vtt_fixed";
+ vin-supply = <&smps3_reg>;
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-always-on;
+ regulator-boot-on;
+ enable-active-high;
+ gpio = <&gpio7 11 GPIO_ACTIVE_HIGH>;
+ };
+
+ leds {
+ compatible = "gpio-leds";
+
+ led0 {
+ label = "beagle-x15:usr0";
+ gpios = <&gpio7 9 GPIO_ACTIVE_HIGH>;
+ linux,default-trigger = "heartbeat";
+ default-state = "off";
+ };
+
+ led1 {
+ label = "beagle-x15:usr1";
+ gpios = <&gpio7 8 GPIO_ACTIVE_HIGH>;
+ linux,default-trigger = "cpu0";
+ default-state = "off";
+ };
+
+ led2 {
+ label = "beagle-x15:usr2";
+ gpios = <&gpio7 14 GPIO_ACTIVE_HIGH>;
+ linux,default-trigger = "mmc0";
+ default-state = "off";
+ };
+
+ led3 {
+ label = "beagle-x15:usr3";
+ gpios = <&gpio7 15 GPIO_ACTIVE_HIGH>;
+ linux,default-trigger = "disk-activity";
+ default-state = "off";
+ };
+ };
+
+ gpio_fan: gpio_fan {
+ /* Based on 5v 500mA AFB02505HHB */
+ compatible = "gpio-fan";
+ gpios = <&tps659038_gpio 2 GPIO_ACTIVE_HIGH>;
+ gpio-fan,speed-map = <0 0>,
+ <13000 1>;
+ #cooling-cells = <2>;
+ };
+
+ hdmi0: connector {
+ compatible = "hdmi-connector";
+ label = "hdmi";
+
+ type = "a";
+
+ port {
+ hdmi_connector_in: endpoint {
+ remote-endpoint = <&tpd12s015_out>;
+ };
+ };
+ };
+
+ tpd12s015: encoder {
+ compatible = "ti,tpd12s015";
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ port@0 {
+ reg = <0>;
+
+ tpd12s015_in: endpoint {
+ remote-endpoint = <&hdmi_out>;
+ };
+ };
+
+ port@1 {
+ reg = <1>;
+
+ tpd12s015_out: endpoint {
+ remote-endpoint = <&hdmi_connector_in>;
+ };
+ };
+ };
+ };
+
+ sound0: sound0 {
+ compatible = "simple-audio-card";
+ simple-audio-card,name = "BeagleBoard-X15";
+ simple-audio-card,widgets =
+ "Line", "Line Out",
+ "Line", "Line In";
+ simple-audio-card,routing =
+ "Line Out", "LLOUT",
+ "Line Out", "RLOUT",
+ "MIC2L", "Line In",
+ "MIC2R", "Line In";
+ simple-audio-card,format = "dsp_b";
+ simple-audio-card,bitclock-master = <&sound0_master>;
+ simple-audio-card,frame-master = <&sound0_master>;
+ simple-audio-card,bitclock-inversion;
+
+ simple-audio-card,cpu {
+ sound-dai = <&mcasp3>;
+ };
+
+ sound0_master: simple-audio-card,codec {
+ sound-dai = <&tlv320aic3104>;
+ clocks = <&clkout2_clk>;
+ };
+ };
+};
+
+&dra7_pmx_core {
+ mmc1_pins_default: mmc1_pins_default {
+ pinctrl-single,pins = <
+ DRA7XX_CORE_IOPAD(0x376c, PIN_INPUT | MUX_MODE14) /* mmc1sdcd.gpio219 */
+ DRA7XX_CORE_IOPAD(0x3754, PIN_INPUT_PULLUP | MUX_MODE0) /* mmc1_clk.clk */
+ DRA7XX_CORE_IOPAD(0x3758, PIN_INPUT_PULLUP | MUX_MODE0) /* mmc1_cmd.cmd */
+ DRA7XX_CORE_IOPAD(0x375c, PIN_INPUT_PULLUP | MUX_MODE0) /* mmc1_dat0.dat0 */
+ DRA7XX_CORE_IOPAD(0x3760, PIN_INPUT_PULLUP | MUX_MODE0) /* mmc1_dat1.dat1 */
+ DRA7XX_CORE_IOPAD(0x3764, PIN_INPUT_PULLUP | MUX_MODE0) /* mmc1_dat2.dat2 */
+ DRA7XX_CORE_IOPAD(0x3768, PIN_INPUT_PULLUP | MUX_MODE0) /* mmc1_dat3.dat3 */
+ >;
+ };
+
+ mmc2_pins_default: mmc2_pins_default {
+ pinctrl-single,pins = <
+ DRA7XX_CORE_IOPAD(0x349c, PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_a23.mmc2_clk */
+ DRA7XX_CORE_IOPAD(0x34b0, PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_cs1.mmc2_cmd */
+ DRA7XX_CORE_IOPAD(0x34a0, PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_a24.mmc2_dat0 */
+ DRA7XX_CORE_IOPAD(0x34a4, PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_a25.mmc2_dat1 */
+ DRA7XX_CORE_IOPAD(0x34a8, PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_a26.mmc2_dat2 */
+ DRA7XX_CORE_IOPAD(0x34ac, PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_a27.mmc2_dat3 */
+ DRA7XX_CORE_IOPAD(0x348c, PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_a19.mmc2_dat4 */
+ DRA7XX_CORE_IOPAD(0x3490, PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_a20.mmc2_dat5 */
+ DRA7XX_CORE_IOPAD(0x3494, PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_a21.mmc2_dat6 */
+ DRA7XX_CORE_IOPAD(0x3498, PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_a22.mmc2_dat7 */
+ >;
+ };
+};
+&i2c1 {
+ status = "okay";
+ clock-frequency = <400000>;
+
+ tps659038: tps659038@58 {
+ compatible = "ti,tps659038";
+ reg = <0x58>;
+ interrupt-parent = <&gpio1>;
+ interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
+
+ #interrupt-cells = <2>;
+ interrupt-controller;
+
+ ti,system-power-controller;
+
+ tps659038_pmic {
+ compatible = "ti,tps659038-pmic";
+
+ regulators {
+ smps12_reg: smps12 {
+ /* VDD_MPU */
+ regulator-name = "smps12";
+ regulator-min-microvolt = < 850000>;
+ regulator-max-microvolt = <1250000>;
+ regulator-always-on;
+ regulator-boot-on;
+ };
+
+ smps3_reg: smps3 {
+ /* VDD_DDR */
+ regulator-name = "smps3";
+ regulator-min-microvolt = <1350000>;
+ regulator-max-microvolt = <1350000>;
+ regulator-always-on;
+ regulator-boot-on;
+ };
+
+ smps45_reg: smps45 {
+ /* VDD_DSPEVE, VDD_IVA, VDD_GPU */
+ regulator-name = "smps45";
+ regulator-min-microvolt = < 850000>;
+ regulator-max-microvolt = <1250000>;
+ regulator-always-on;
+ regulator-boot-on;
+ };
+
+ smps6_reg: smps6 {
+ /* VDD_CORE */
+ regulator-name = "smps6";
+ regulator-min-microvolt = <850000>;
+ regulator-max-microvolt = <1150000>;
+ regulator-always-on;
+ regulator-boot-on;
+ };
+
+ /* SMPS7 unused */
+
+ smps8_reg: smps8 {
+ /* VDD_1V8 */
+ regulator-name = "smps8";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-always-on;
+ regulator-boot-on;
+ };
+
+ /* SMPS9 unused */
+
+ ldo1_reg: ldo1 {
+ /* VDD_SD / VDDSHV8 */
+ regulator-name = "ldo1";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ ldo2_reg: ldo2 {
+ /* VDD_SHV5 */
+ regulator-name = "ldo2";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-always-on;
+ regulator-boot-on;
+ };
+
+ ldo3_reg: ldo3 {
+ /* VDDA_1V8_PHYA */
+ regulator-name = "ldo3";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-always-on;
+ regulator-boot-on;
+ };
+
+ ldo4_reg: ldo4 {
+ /* VDDA_1V8_PHYB */
+ regulator-name = "ldo4";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-always-on;
+ regulator-boot-on;
+ };
+
+ ldo9_reg: ldo9 {
+ /* VDD_RTC */
+ regulator-name = "ldo9";
+ regulator-min-microvolt = <1050000>;
+ regulator-max-microvolt = <1050000>;
+ regulator-always-on;
+ regulator-boot-on;
+ };
+
+ ldoln_reg: ldoln {
+ /* VDDA_1V8_PLL */
+ regulator-name = "ldoln";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-always-on;
+ regulator-boot-on;
+ };
+
+ ldousb_reg: ldousb {
+ /* VDDA_3V_USB: VDDA_USBHS33 */
+ regulator-name = "ldousb";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-boot-on;
+ };
+
+ regen1: regen1 {
+ /* VDD_3V3_ON */
+ regulator-name = "regen1";
+ regulator-boot-on;
+ regulator-always-on;
+ };
+ };
+ };
+
+ tps659038_rtc: tps659038_rtc {
+ compatible = "ti,palmas-rtc";
+ interrupt-parent = <&tps659038>;
+ interrupts = <8 IRQ_TYPE_EDGE_FALLING>;
+ wakeup-source;
+ };
+
+ tps659038_pwr_button: tps659038_pwr_button {
+ compatible = "ti,palmas-pwrbutton";
+ interrupt-parent = <&tps659038>;
+ interrupts = <1 IRQ_TYPE_EDGE_FALLING>;
+ wakeup-source;
+ ti,palmas-long-press-seconds = <12>;
+ };
+
+ tps659038_gpio: tps659038_gpio {
+ compatible = "ti,palmas-gpio";
+ gpio-controller;
+ #gpio-cells = <2>;
+ };
+
+ extcon_usb2: tps659038_usb {
+ compatible = "ti,palmas-usb-vid";
+ ti,enable-vbus-detection;
+ vbus-gpio = <&gpio4 21 GPIO_ACTIVE_HIGH>;
+ };
+
+ };
+
+ tmp102: tmp102@48 {
+ compatible = "ti,tmp102";
+ reg = <0x48>;
+ interrupt-parent = <&gpio7>;
+ interrupts = <16 IRQ_TYPE_LEVEL_LOW>;
+ #thermal-sensor-cells = <1>;
+ };
+
+ tlv320aic3104: tlv320aic3104@18 {
+ #sound-dai-cells = <0>;
+ compatible = "ti,tlv320aic3104";
+ reg = <0x18>;
+ assigned-clocks = <&clkoutmux2_clk_mux>;
+ assigned-clock-parents = <&sys_clk2_dclk_div>;
+
+ status = "okay";
+ adc-settle-ms = <40>;
+
+ AVDD-supply = <&vdd_3v3>;
+ IOVDD-supply = <&vdd_3v3>;
+ DRVDD-supply = <&vdd_3v3>;
+ DVDD-supply = <&aic_dvdd>;
+ };
+
+ eeprom: eeprom@50 {
+ compatible = "at,24c32";
+ reg = <0x50>;
+ };
+};
+
+&i2c3 {
+ status = "okay";
+ clock-frequency = <400000>;
+
+ mcp_rtc: rtc@6f {
+ compatible = "microchip,mcp7941x";
+ reg = <0x6f>;
+ interrupts-extended = <&crossbar_mpu GIC_SPI 2 IRQ_TYPE_EDGE_RISING>,
+ <&dra7_pmx_core 0x424>;
+ interrupt-names = "irq", "wakeup";
+
+ vcc-supply = <&vdd_3v3>;
+ wakeup-source;
+ };
+};
+
+&gpio7 {
+ ti,no-reset-on-init;
+ ti,no-idle-on-init;
+};
+
+&cpu0 {
+ cpu0-supply = <&smps12_reg>;
+ voltage-tolerance = <1>;
+};
+
+&uart3 {
+ status = "okay";
+ interrupts-extended = <&crossbar_mpu GIC_SPI 69 IRQ_TYPE_LEVEL_HIGH>,
+ <&dra7_pmx_core 0x3f8>;
+};
+
+&mac {
+ status = "okay";
+ dual_emac;
+};
+
+&cpsw_emac0 {
+ phy_id = <&davinci_mdio>, <1>;
+ phy-mode = "rgmii";
+ dual_emac_res_vlan = <1>;
+};
+
+&cpsw_emac1 {
+ phy_id = <&davinci_mdio>, <2>;
+ phy-mode = "rgmii";
+ dual_emac_res_vlan = <2>;
+};
+
+&mmc1 {
+ status = "okay";
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&mmc1_pins_default>;
+
+ bus-width = <4>;
+ cd-gpios = <&gpio6 27 GPIO_ACTIVE_LOW>; /* gpio 219 */
+};
+
+&mmc2 {
+ status = "okay";
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&mmc1_pins_default>;
+
+ vmmc-supply = <&vdd_3v3>;
+ bus-width = <8>;
+ ti,non-removable;
+ cap-mmc-dual-data-rate;
+};
+
+&sata {
+ status = "okay";
+};
+
+&usb2_phy1 {
+ phy-supply = <&ldousb_reg>;
+};
+
+&usb2_phy2 {
+ phy-supply = <&ldousb_reg>;
+};
+
+&usb1 {
+ dr_mode = "host";
+};
+
+&omap_dwc3_2 {
+ extcon = <&extcon_usb2>;
+};
+
+&usb2 {
+ /*
+ * Stand alone usage is peripheral only.
+ * However, with some resistor modifications
+ * this port can be used via expansion connectors
+ * as "host" or "dual-role". If so, provide
+ * the necessary dr_mode override in the expansion
+ * board's DT.
+ */
+ dr_mode = "peripheral";
+};
+
+&cpu_trips {
+ cpu_alert1: cpu_alert1 {
+ temperature = <50000>; /* millicelsius */
+ hysteresis = <2000>; /* millicelsius */
+ type = "active";
+ };
+};
+
+&cpu_cooling_maps {
+ map1 {
+ trip = <&cpu_alert1>;
+ cooling-device = <&gpio_fan THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
+ };
+};
+
+&thermal_zones {
+ board_thermal: board_thermal {
+ polling-delay-passive = <1250>; /* milliseconds */
+ polling-delay = <1500>; /* milliseconds */
+
+ /* sensor ID */
+ thermal-sensors = <&tmp102 0>;
+
+ board_trips: trips {
+ board_alert0: board_alert {
+ temperature = <40000>; /* millicelsius */
+ hysteresis = <2000>; /* millicelsius */
+ type = "active";
+ };
+
+ board_crit: board_crit {
+ temperature = <105000>; /* millicelsius */
+ hysteresis = <0>; /* millicelsius */
+ type = "critical";
+ };
+ };
+
+ board_cooling_maps: cooling-maps {
+ map0 {
+ trip = <&board_alert0>;
+ cooling-device =
+ <&gpio_fan THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
+ };
+ };
+ };
+};
+
+&dss {
+ status = "ok";
+
+ vdda_video-supply = <&ldoln_reg>;
+};
+
+&hdmi {
+ status = "ok";
+ vdda-supply = <&ldo4_reg>;
+
+ port {
+ hdmi_out: endpoint {
+ remote-endpoint = <&tpd12s015_in>;
+ };
+ };
+};
+
+&pcie1 {
+ gpios = <&gpio2 8 GPIO_ACTIVE_LOW>;
+};
+
+&mcasp3 {
+ #sound-dai-cells = <0>;
+ assigned-clocks = <&mcasp3_ahclkx_mux>;
+ assigned-clock-parents = <&sys_clkin2>;
+ status = "okay";
+
+ op-mode = <0>; /* MCASP_IIS_MODE */
+ tdm-slots = <2>;
+ /* 4 serializers */
+ serial-dir = < /* 0: INACTIVE, 1: TX, 2: RX */
+ 1 2 0 0
+ >;
+ tx-num-evt = <32>;
+ rx-num-evt = <32>;
+};
+
+&mailbox5 {
+ status = "okay";
+ mbox_ipu1_ipc3x: mbox_ipu1_ipc3x {
+ status = "okay";
+ };
+ mbox_dsp1_ipc3x: mbox_dsp1_ipc3x {
+ status = "okay";
+ };
+};
+
+&mailbox6 {
+ status = "okay";
+ mbox_ipu2_ipc3x: mbox_ipu2_ipc3x {
+ status = "okay";
+ };
+ mbox_dsp2_ipc3x: mbox_dsp2_ipc3x {
+ status = "okay";
+ };
+};
diff --git a/arch/arm/boot/dts/am57xx-beagle-x15-revb1.dts b/arch/arm/boot/dts/am57xx-beagle-x15-revb1.dts
new file mode 100644
index 0000000..ca85570
--- /dev/null
+++ b/arch/arm/boot/dts/am57xx-beagle-x15-revb1.dts
@@ -0,0 +1,24 @@
+/*
+ * Copyright (C) 2014-2016 Texas Instruments Incorporated - http://www.ti.com/
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+#include "am57xx-beagle-x15-common.dtsi"
+
+/ {
+ model = "TI AM5728 BeagleBoard-X15 rev B1";
+};
+
+&tpd12s015 {
+ gpios = <&gpio7 10 GPIO_ACTIVE_HIGH>, /* gpio7_10, CT CP HPD */
+ <&gpio2 30 GPIO_ACTIVE_HIGH>, /* gpio2_30, LS OE */
+ <&gpio7 12 GPIO_ACTIVE_HIGH>; /* gpio7_12/sp1_cs2, HPD */
+};
+
+&mmc1 {
+ vmmc-supply = <&vdd_3v3>;
+ vmmc-aux-supply = <&ldo1_reg>;
+};
diff --git a/arch/arm/boot/dts/am57xx-beagle-x15.dts b/arch/arm/boot/dts/am57xx-beagle-x15.dts
index 9067ca0..8c66f2e 100644
--- a/arch/arm/boot/dts/am57xx-beagle-x15.dts
+++ b/arch/arm/boot/dts/am57xx-beagle-x15.dts
@@ -1,822 +1,24 @@
/*
- * Copyright (C) 2014 Texas Instruments Incorporated - http://www.ti.com/
+ * Copyright (C) 2014-2016 Texas Instruments Incorporated - http://www.ti.com/
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License version 2 as
* published by the Free Software Foundation.
*/
-/dts-v1/;
-#include "dra74x.dtsi"
-#include "am57xx-commercial-grade.dtsi"
-#include <dt-bindings/gpio/gpio.h>
-#include <dt-bindings/interrupt-controller/irq.h>
+#include "am57xx-beagle-x15-common.dtsi"
/ {
+ /* NOTE: This describes the "original" pre-production A2 revision */
model = "TI AM5728 BeagleBoard-X15";
- compatible = "ti,am572x-beagle-x15", "ti,am5728", "ti,dra742", "ti,dra74", "ti,dra7";
-
- aliases {
- rtc0 = &mcp_rtc;
- rtc1 = &tps659038_rtc;
- rtc2 = &rtc;
- display0 = &hdmi0;
- };
-
- memory@0 {
- device_type = "memory";
- reg = <0x0 0x80000000 0x0 0x80000000>;
- };
-
- vdd_3v3: fixedregulator-vdd_3v3 {
- compatible = "regulator-fixed";
- regulator-name = "vdd_3v3";
- vin-supply = <&regen1>;
- regulator-min-microvolt = <3300000>;
- regulator-max-microvolt = <3300000>;
- };
-
- aic_dvdd: fixedregulator-aic_dvdd {
- compatible = "regulator-fixed";
- regulator-name = "aic_dvdd_fixed";
- vin-supply = <&vdd_3v3>;
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
- };
-
- vtt_fixed: fixedregulator-vtt {
- /* TPS51200 */
- compatible = "regulator-fixed";
- regulator-name = "vtt_fixed";
- vin-supply = <&smps3_reg>;
- regulator-min-microvolt = <3300000>;
- regulator-max-microvolt = <3300000>;
- regulator-always-on;
- regulator-boot-on;
- enable-active-high;
- gpio = <&gpio7 11 GPIO_ACTIVE_HIGH>;
- };
-
- leds {
- compatible = "gpio-leds";
- pinctrl-names = "default";
- pinctrl-0 = <&leds_pins_default>;
-
- led0 {
- label = "beagle-x15:usr0";
- gpios = <&gpio7 9 GPIO_ACTIVE_HIGH>;
- linux,default-trigger = "heartbeat";
- default-state = "off";
- };
-
- led1 {
- label = "beagle-x15:usr1";
- gpios = <&gpio7 8 GPIO_ACTIVE_HIGH>;
- linux,default-trigger = "cpu0";
- default-state = "off";
- };
-
- led2 {
- label = "beagle-x15:usr2";
- gpios = <&gpio7 14 GPIO_ACTIVE_HIGH>;
- linux,default-trigger = "mmc0";
- default-state = "off";
- };
-
- led3 {
- label = "beagle-x15:usr3";
- gpios = <&gpio7 15 GPIO_ACTIVE_HIGH>;
- linux,default-trigger = "disk-activity";
- default-state = "off";
- };
- };
-
- gpio_fan: gpio_fan {
- /* Based on 5v 500mA AFB02505HHB */
- compatible = "gpio-fan";
- gpios = <&tps659038_gpio 2 GPIO_ACTIVE_HIGH>;
- gpio-fan,speed-map = <0 0>,
- <13000 1>;
- #cooling-cells = <2>;
- };
-
- hdmi0: connector {
- compatible = "hdmi-connector";
- label = "hdmi";
-
- type = "a";
-
- port {
- hdmi_connector_in: endpoint {
- remote-endpoint = <&tpd12s015_out>;
- };
- };
- };
-
- tpd12s015: encoder {
- compatible = "ti,tpd12s015";
-
- pinctrl-names = "default";
- pinctrl-0 = <&tpd12s015_pins>;
-
- gpios = <&gpio7 10 GPIO_ACTIVE_HIGH>, /* gpio7_10, CT CP HPD */
- <&gpio6 28 GPIO_ACTIVE_HIGH>, /* gpio6_28, LS OE */
- <&gpio7 12 GPIO_ACTIVE_HIGH>; /* gpio7_12/sp1_cs2, HPD */
-
- ports {
- #address-cells = <1>;
- #size-cells = <0>;
-
- port@0 {
- reg = <0>;
-
- tpd12s015_in: endpoint {
- remote-endpoint = <&hdmi_out>;
- };
- };
-
- port@1 {
- reg = <1>;
-
- tpd12s015_out: endpoint {
- remote-endpoint = <&hdmi_connector_in>;
- };
- };
- };
- };
-
- sound0: sound0 {
- compatible = "simple-audio-card";
- simple-audio-card,name = "BeagleBoard-X15";
- simple-audio-card,widgets =
- "Line", "Line Out",
- "Line", "Line In";
- simple-audio-card,routing =
- "Line Out", "LLOUT",
- "Line Out", "RLOUT",
- "MIC2L", "Line In",
- "MIC2R", "Line In";
- simple-audio-card,format = "dsp_b";
- simple-audio-card,bitclock-master = <&sound0_master>;
- simple-audio-card,frame-master = <&sound0_master>;
- simple-audio-card,bitclock-inversion;
-
- simple-audio-card,cpu {
- sound-dai = <&mcasp3>;
- };
-
- sound0_master: simple-audio-card,codec {
- sound-dai = <&tlv320aic3104>;
- clocks = <&clkout2_clk>;
- };
- };
};
-&dra7_pmx_core {
- leds_pins_default: leds_pins_default {
- pinctrl-single,pins = <
- DRA7XX_CORE_IOPAD(0x37a8, PIN_OUTPUT | MUX_MODE14) /* spi1_d1.gpio7_8 */
- DRA7XX_CORE_IOPAD(0x37ac, PIN_OUTPUT | MUX_MODE14) /* spi1_d0.gpio7_9 */
- DRA7XX_CORE_IOPAD(0x37c0, PIN_OUTPUT | MUX_MODE14) /* spi2_sclk.gpio7_14 */
- DRA7XX_CORE_IOPAD(0x37c4, PIN_OUTPUT | MUX_MODE14) /* spi2_d1.gpio7_15 */
- >;
- };
-
- i2c1_pins_default: i2c1_pins_default {
- pinctrl-single,pins = <
- DRA7XX_CORE_IOPAD(0x3800, PIN_INPUT_PULLUP | MUX_MODE0) /* i2c1_sda.sda */
- DRA7XX_CORE_IOPAD(0x3804, PIN_INPUT_PULLUP | MUX_MODE0) /* i2c1_scl.scl */
- >;
- };
-
- hdmi_pins: pinmux_hdmi_pins {
- pinctrl-single,pins = <
- DRA7XX_CORE_IOPAD(0x3808, PIN_INPUT | MUX_MODE1) /* i2c2_sda.hdmi1_ddc_scl */
- DRA7XX_CORE_IOPAD(0x380c, PIN_INPUT | MUX_MODE1) /* i2c2_scl.hdmi1_ddc_sda */
- >;
- };
-
- i2c3_pins_default: i2c3_pins_default {
- pinctrl-single,pins = <
- DRA7XX_CORE_IOPAD(0x36a4, PIN_INPUT| MUX_MODE10) /* mcasp1_aclkx.i2c3_sda */
- DRA7XX_CORE_IOPAD(0x36a8, PIN_INPUT| MUX_MODE10) /* mcasp1_fsx.i2c3_scl */
- >;
- };
-
- uart3_pins_default: uart3_pins_default {
- pinctrl-single,pins = <
- DRA7XX_CORE_IOPAD(0x37f8, PIN_INPUT_SLEW | MUX_MODE2) /* uart2_ctsn.uart3_rxd */
- DRA7XX_CORE_IOPAD(0x37fc, PIN_INPUT_SLEW | MUX_MODE1) /* uart2_rtsn.uart3_txd */
- >;
- };
-
- mmc1_pins_default: mmc1_pins_default {
- pinctrl-single,pins = <
- DRA7XX_CORE_IOPAD(0x376c, PIN_INPUT | MUX_MODE14) /* mmc1sdcd.gpio219 */
- DRA7XX_CORE_IOPAD(0x3754, PIN_INPUT_PULLUP | MUX_MODE0) /* mmc1_clk.clk */
- DRA7XX_CORE_IOPAD(0x3758, PIN_INPUT_PULLUP | MUX_MODE0) /* mmc1_cmd.cmd */
- DRA7XX_CORE_IOPAD(0x375c, PIN_INPUT_PULLUP | MUX_MODE0) /* mmc1_dat0.dat0 */
- DRA7XX_CORE_IOPAD(0x3760, PIN_INPUT_PULLUP | MUX_MODE0) /* mmc1_dat1.dat1 */
- DRA7XX_CORE_IOPAD(0x3764, PIN_INPUT_PULLUP | MUX_MODE0) /* mmc1_dat2.dat2 */
- DRA7XX_CORE_IOPAD(0x3768, PIN_INPUT_PULLUP | MUX_MODE0) /* mmc1_dat3.dat3 */
- >;
- };
-
- mmc2_pins_default: mmc2_pins_default {
- pinctrl-single,pins = <
- DRA7XX_CORE_IOPAD(0x349c, PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_a23.mmc2_clk */
- DRA7XX_CORE_IOPAD(0x34b0, PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_cs1.mmc2_cmd */
- DRA7XX_CORE_IOPAD(0x34a0, PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_a24.mmc2_dat0 */
- DRA7XX_CORE_IOPAD(0x34a4, PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_a25.mmc2_dat1 */
- DRA7XX_CORE_IOPAD(0x34a8, PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_a26.mmc2_dat2 */
- DRA7XX_CORE_IOPAD(0x34ac, PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_a27.mmc2_dat3 */
- DRA7XX_CORE_IOPAD(0x348c, PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_a19.mmc2_dat4 */
- DRA7XX_CORE_IOPAD(0x3490, PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_a20.mmc2_dat5 */
- DRA7XX_CORE_IOPAD(0x3494, PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_a21.mmc2_dat6 */
- DRA7XX_CORE_IOPAD(0x3498, PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_a22.mmc2_dat7 */
- >;
- };
-
- cpsw_pins_default: cpsw_pins_default {
- pinctrl-single,pins = <
- /* Slave 1 */
- DRA7XX_CORE_IOPAD(0x3650, PIN_OUTPUT | MUX_MODE0) /* rgmii1_tclk */
- DRA7XX_CORE_IOPAD(0x3654, PIN_OUTPUT | MUX_MODE0) /* rgmii1_tctl */
- DRA7XX_CORE_IOPAD(0x3658, PIN_OUTPUT | MUX_MODE0) /* rgmii1_td3 */
- DRA7XX_CORE_IOPAD(0x365c, PIN_OUTPUT | MUX_MODE0) /* rgmii1_td2 */
- DRA7XX_CORE_IOPAD(0x3660, PIN_OUTPUT | MUX_MODE0) /* rgmii1_td1 */
- DRA7XX_CORE_IOPAD(0x3664, PIN_OUTPUT | MUX_MODE0) /* rgmii1_td0 */
- DRA7XX_CORE_IOPAD(0x3668, PIN_INPUT | MUX_MODE0) /* rgmii1_rclk */
- DRA7XX_CORE_IOPAD(0x366c, PIN_INPUT | MUX_MODE0) /* rgmii1_rctl */
- DRA7XX_CORE_IOPAD(0x3670, PIN_INPUT | MUX_MODE0) /* rgmii1_rd3 */
- DRA7XX_CORE_IOPAD(0x3674, PIN_INPUT | MUX_MODE0) /* rgmii1_rd2 */
- DRA7XX_CORE_IOPAD(0x3678, PIN_INPUT | MUX_MODE0) /* rgmii1_rd1 */
- DRA7XX_CORE_IOPAD(0x367c, PIN_INPUT | MUX_MODE0) /* rgmii1_rd0 */
-
- /* Slave 2 */
- DRA7XX_CORE_IOPAD(0x3598, PIN_OUTPUT | MUX_MODE3) /* rgmii2_tclk */
- DRA7XX_CORE_IOPAD(0x359c, PIN_OUTPUT | MUX_MODE3) /* rgmii2_tctl */
- DRA7XX_CORE_IOPAD(0x35a0, PIN_OUTPUT | MUX_MODE3) /* rgmii2_td3 */
- DRA7XX_CORE_IOPAD(0x35a4, PIN_OUTPUT | MUX_MODE3) /* rgmii2_td2 */
- DRA7XX_CORE_IOPAD(0x35a8, PIN_OUTPUT | MUX_MODE3) /* rgmii2_td1 */
- DRA7XX_CORE_IOPAD(0x35ac, PIN_OUTPUT | MUX_MODE3) /* rgmii2_td0 */
- DRA7XX_CORE_IOPAD(0x35b0, PIN_INPUT | MUX_MODE3) /* rgmii2_rclk */
- DRA7XX_CORE_IOPAD(0x35b4, PIN_INPUT | MUX_MODE3) /* rgmii2_rctl */
- DRA7XX_CORE_IOPAD(0x35b8, PIN_INPUT | MUX_MODE3) /* rgmii2_rd3 */
- DRA7XX_CORE_IOPAD(0x35bc, PIN_INPUT | MUX_MODE3) /* rgmii2_rd2 */
- DRA7XX_CORE_IOPAD(0x35c0, PIN_INPUT | MUX_MODE3) /* rgmii2_rd1 */
- DRA7XX_CORE_IOPAD(0x35c4, PIN_INPUT | MUX_MODE3) /* rgmii2_rd0 */
- >;
-
- };
-
- cpsw_pins_sleep: cpsw_pins_sleep {
- pinctrl-single,pins = <
- /* Slave 1 */
- DRA7XX_CORE_IOPAD(0x3650, PIN_INPUT | MUX_MODE15)
- DRA7XX_CORE_IOPAD(0x3654, PIN_INPUT | MUX_MODE15)
- DRA7XX_CORE_IOPAD(0x3658, PIN_INPUT | MUX_MODE15)
- DRA7XX_CORE_IOPAD(0x365c, PIN_INPUT | MUX_MODE15)
- DRA7XX_CORE_IOPAD(0x3660, PIN_INPUT | MUX_MODE15)
- DRA7XX_CORE_IOPAD(0x3664, PIN_INPUT | MUX_MODE15)
- DRA7XX_CORE_IOPAD(0x3668, PIN_INPUT | MUX_MODE15)
- DRA7XX_CORE_IOPAD(0x366c, PIN_INPUT | MUX_MODE15)
- DRA7XX_CORE_IOPAD(0x3670, PIN_INPUT | MUX_MODE15)
- DRA7XX_CORE_IOPAD(0x3674, PIN_INPUT | MUX_MODE15)
- DRA7XX_CORE_IOPAD(0x3678, PIN_INPUT | MUX_MODE15)
- DRA7XX_CORE_IOPAD(0x367c, PIN_INPUT | MUX_MODE15)
-
- /* Slave 2 */
- DRA7XX_CORE_IOPAD(0x3598, PIN_INPUT | MUX_MODE15)
- DRA7XX_CORE_IOPAD(0x359c, PIN_INPUT | MUX_MODE15)
- DRA7XX_CORE_IOPAD(0x35a0, PIN_INPUT | MUX_MODE15)
- DRA7XX_CORE_IOPAD(0x35a4, PIN_INPUT | MUX_MODE15)
- DRA7XX_CORE_IOPAD(0x35a8, PIN_INPUT | MUX_MODE15)
- DRA7XX_CORE_IOPAD(0x35ac, PIN_INPUT | MUX_MODE15)
- DRA7XX_CORE_IOPAD(0x35b0, PIN_INPUT | MUX_MODE15)
- DRA7XX_CORE_IOPAD(0x35b4, PIN_INPUT | MUX_MODE15)
- DRA7XX_CORE_IOPAD(0x35b8, PIN_INPUT | MUX_MODE15)
- DRA7XX_CORE_IOPAD(0x35bc, PIN_INPUT | MUX_MODE15)
- DRA7XX_CORE_IOPAD(0x35c0, PIN_INPUT | MUX_MODE15)
- DRA7XX_CORE_IOPAD(0x35c4, PIN_INPUT | MUX_MODE15)
- >;
- };
-
- davinci_mdio_pins_default: davinci_mdio_pins_default {
- pinctrl-single,pins = <
- /* MDIO */
- DRA7XX_CORE_IOPAD(0x363c, PIN_OUTPUT_PULLUP | MUX_MODE0) /* mdio_mclk */
- DRA7XX_CORE_IOPAD(0x3640, PIN_INPUT_PULLUP | MUX_MODE0) /* mdio_d */
- >;
- };
-
- davinci_mdio_pins_sleep: davinci_mdio_pins_sleep {
- pinctrl-single,pins = <
- DRA7XX_CORE_IOPAD(0x363c, PIN_INPUT | MUX_MODE15)
- DRA7XX_CORE_IOPAD(0x3640, PIN_INPUT | MUX_MODE15)
- >;
- };
-
- tps659038_pins_default: tps659038_pins_default {
- pinctrl-single,pins = <
- DRA7XX_CORE_IOPAD(0x3818, PIN_INPUT_PULLUP | MUX_MODE14) /* wakeup0.gpio1_0 */
- >;
- };
-
- tmp102_pins_default: tmp102_pins_default {
- pinctrl-single,pins = <
- DRA7XX_CORE_IOPAD(0x37c8, PIN_INPUT_PULLUP | MUX_MODE14) /* spi2_d0.gpio7_16 */
- >;
- };
-
- mcp79410_pins_default: mcp79410_pins_default {
- pinctrl-single,pins = <
- DRA7XX_CORE_IOPAD(0x3824, PIN_INPUT_PULLUP | MUX_MODE1) /* wakeup3.sys_nirq1 */
- >;
- };
-
- usb1_pins: pinmux_usb1_pins {
- pinctrl-single,pins = <
- DRA7XX_CORE_IOPAD(0x3680, PIN_INPUT_SLEW | MUX_MODE0) /* usb1_drvvbus */
- >;
- };
-
- tpd12s015_pins: pinmux_tpd12s015_pins {
- pinctrl-single,pins = <
- DRA7XX_CORE_IOPAD(0x37b0, PIN_OUTPUT | MUX_MODE14) /* gpio7_10 CT_CP_HPD */
- DRA7XX_CORE_IOPAD(0x37b8, PIN_INPUT_PULLDOWN | MUX_MODE14) /* gpio7_12 HPD */
- DRA7XX_CORE_IOPAD(0x3770, PIN_OUTPUT | MUX_MODE14) /* gpio6_28 LS_OE */
- >;
- };
-
- clkout2_pins_default: clkout2_pins_default {
- pinctrl-single,pins = <
- DRA7XX_CORE_IOPAD(0x3694, PIN_OUTPUT_PULLDOWN | MUX_MODE9) /* xref_clk0.clkout2 */
- >;
- };
-
- clkout2_pins_sleep: clkout2_pins_sleep {
- pinctrl-single,pins = <
- DRA7XX_CORE_IOPAD(0x3694, PIN_INPUT | MUX_MODE15) /* xref_clk0.clkout2 */
- >;
- };
-
- mcasp3_pins_default: mcasp3_pins_default {
- pinctrl-single,pins = <
- DRA7XX_CORE_IOPAD(0x3724, PIN_INPUT_PULLDOWN | MUX_MODE0) /* mcasp3_aclkx.mcasp3_aclkx */
- DRA7XX_CORE_IOPAD(0x3728, PIN_INPUT_PULLDOWN | MUX_MODE0) /* mcasp3_fsx.mcasp3_fsx */
- DRA7XX_CORE_IOPAD(0x372c, PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* mcasp3_axr0.mcasp3_axr0 */
- DRA7XX_CORE_IOPAD(0x3730, PIN_INPUT_PULLDOWN | MUX_MODE0) /* mcasp3_axr1.mcasp3_axr1 */
- >;
- };
-
- mcasp3_pins_sleep: mcasp3_pins_sleep {
- pinctrl-single,pins = <
- DRA7XX_CORE_IOPAD(0x3724, PIN_INPUT | MUX_MODE15)
- DRA7XX_CORE_IOPAD(0x3728, PIN_INPUT | MUX_MODE15)
- DRA7XX_CORE_IOPAD(0x372c, PIN_INPUT | MUX_MODE15)
- DRA7XX_CORE_IOPAD(0x3730, PIN_INPUT | MUX_MODE15)
- >;
- };
-};
-
-&i2c1 {
- status = "okay";
- pinctrl-names = "default";
- pinctrl-0 = <&i2c1_pins_default>;
- clock-frequency = <400000>;
-
- tps659038: tps659038@58 {
- compatible = "ti,tps659038";
- reg = <0x58>;
- interrupt-parent = <&gpio1>;
- interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
-
- pinctrl-names = "default";
- pinctrl-0 = <&tps659038_pins_default>;
-
- #interrupt-cells = <2>;
- interrupt-controller;
-
- ti,system-power-controller;
-
- tps659038_pmic {
- compatible = "ti,tps659038-pmic";
-
- regulators {
- smps12_reg: smps12 {
- /* VDD_MPU */
- regulator-name = "smps12";
- regulator-min-microvolt = < 850000>;
- regulator-max-microvolt = <1250000>;
- regulator-always-on;
- regulator-boot-on;
- };
-
- smps3_reg: smps3 {
- /* VDD_DDR */
- regulator-name = "smps3";
- regulator-min-microvolt = <1350000>;
- regulator-max-microvolt = <1350000>;
- regulator-always-on;
- regulator-boot-on;
- };
-
- smps45_reg: smps45 {
- /* VDD_DSPEVE, VDD_IVA, VDD_GPU */
- regulator-name = "smps45";
- regulator-min-microvolt = < 850000>;
- regulator-max-microvolt = <1250000>;
- regulator-always-on;
- regulator-boot-on;
- };
-
- smps6_reg: smps6 {
- /* VDD_CORE */
- regulator-name = "smps6";
- regulator-min-microvolt = <850000>;
- regulator-max-microvolt = <1150000>;
- regulator-always-on;
- regulator-boot-on;
- };
-
- /* SMPS7 unused */
-
- smps8_reg: smps8 {
- /* VDD_1V8 */
- regulator-name = "smps8";
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
- regulator-always-on;
- regulator-boot-on;
- };
-
- /* SMPS9 unused */
-
- ldo1_reg: ldo1 {
- /* VDD_SD / VDDSHV8 */
- regulator-name = "ldo1";
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <3300000>;
- regulator-boot-on;
- regulator-always-on;
- };
-
- ldo2_reg: ldo2 {
- /* VDD_SHV5 */
- regulator-name = "ldo2";
- regulator-min-microvolt = <3300000>;
- regulator-max-microvolt = <3300000>;
- regulator-always-on;
- regulator-boot-on;
- };
-
- ldo3_reg: ldo3 {
- /* VDDA_1V8_PHYA */
- regulator-name = "ldo3";
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
- regulator-always-on;
- regulator-boot-on;
- };
-
- ldo4_reg: ldo4 {
- /* VDDA_1V8_PHYB */
- regulator-name = "ldo4";
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
- regulator-always-on;
- regulator-boot-on;
- };
-
- ldo9_reg: ldo9 {
- /* VDD_RTC */
- regulator-name = "ldo9";
- regulator-min-microvolt = <1050000>;
- regulator-max-microvolt = <1050000>;
- regulator-always-on;
- regulator-boot-on;
- };
-
- ldoln_reg: ldoln {
- /* VDDA_1V8_PLL */
- regulator-name = "ldoln";
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
- regulator-always-on;
- regulator-boot-on;
- };
-
- ldousb_reg: ldousb {
- /* VDDA_3V_USB: VDDA_USBHS33 */
- regulator-name = "ldousb";
- regulator-min-microvolt = <3300000>;
- regulator-max-microvolt = <3300000>;
- regulator-boot-on;
- };
-
- regen1: regen1 {
- /* VDD_3V3_ON */
- regulator-name = "regen1";
- regulator-boot-on;
- regulator-always-on;
- };
- };
- };
-
- tps659038_rtc: tps659038_rtc {
- compatible = "ti,palmas-rtc";
- interrupt-parent = <&tps659038>;
- interrupts = <8 IRQ_TYPE_EDGE_FALLING>;
- wakeup-source;
- };
-
- tps659038_pwr_button: tps659038_pwr_button {
- compatible = "ti,palmas-pwrbutton";
- interrupt-parent = <&tps659038>;
- interrupts = <1 IRQ_TYPE_EDGE_FALLING>;
- wakeup-source;
- ti,palmas-long-press-seconds = <12>;
- };
-
- tps659038_gpio: tps659038_gpio {
- compatible = "ti,palmas-gpio";
- gpio-controller;
- #gpio-cells = <2>;
- };
-
- extcon_usb2: tps659038_usb {
- compatible = "ti,palmas-usb-vid";
- ti,enable-vbus-detection;
- vbus-gpio = <&gpio4 21 GPIO_ACTIVE_HIGH>;
- };
-
- };
-
- tmp102: tmp102@48 {
- compatible = "ti,tmp102";
- reg = <0x48>;
- pinctrl-names = "default";
- pinctrl-0 = <&tmp102_pins_default>;
- interrupt-parent = <&gpio7>;
- interrupts = <16 IRQ_TYPE_LEVEL_LOW>;
- #thermal-sensor-cells = <1>;
- };
-
- tlv320aic3104: tlv320aic3104@18 {
- #sound-dai-cells = <0>;
- compatible = "ti,tlv320aic3104";
- reg = <0x18>;
- pinctrl-names = "default", "sleep";
- pinctrl-0 = <&clkout2_pins_default>;
- pinctrl-1 = <&clkout2_pins_sleep>;
- assigned-clocks = <&clkoutmux2_clk_mux>;
- assigned-clock-parents = <&sys_clk2_dclk_div>;
-
- status = "okay";
- adc-settle-ms = <40>;
-
- AVDD-supply = <&vdd_3v3>;
- IOVDD-supply = <&vdd_3v3>;
- DRVDD-supply = <&vdd_3v3>;
- DVDD-supply = <&aic_dvdd>;
- };
-
- eeprom: eeprom@50 {
- compatible = "at,24c32";
- reg = <0x50>;
- };
-};
-
-&i2c3 {
- status = "okay";
- pinctrl-names = "default";
- pinctrl-0 = <&i2c3_pins_default>;
- clock-frequency = <400000>;
-
- mcp_rtc: rtc@6f {
- compatible = "microchip,mcp7941x";
- reg = <0x6f>;
- interrupts-extended = <&crossbar_mpu GIC_SPI 2 IRQ_TYPE_EDGE_RISING>,
- <&dra7_pmx_core 0x424>;
- interrupt-names = "irq", "wakeup";
-
- pinctrl-names = "default";
- pinctrl-0 = <&mcp79410_pins_default>;
-
- vcc-supply = <&vdd_3v3>;
- wakeup-source;
- };
-};
-
-&gpio7 {
- ti,no-reset-on-init;
- ti,no-idle-on-init;
-};
-
-&cpu0 {
- cpu0-supply = <&smps12_reg>;
- voltage-tolerance = <1>;
-};
-
-&uart3 {
- status = "okay";
- interrupts-extended = <&crossbar_mpu GIC_SPI 69 IRQ_TYPE_LEVEL_HIGH>,
- <&dra7_pmx_core 0x3f8>;
-
- pinctrl-names = "default";
- pinctrl-0 = <&uart3_pins_default>;
-};
-
-&mac {
- status = "okay";
- pinctrl-names = "default", "sleep";
- pinctrl-0 = <&cpsw_pins_default>;
- pinctrl-1 = <&cpsw_pins_sleep>;
- dual_emac;
-};
-
-&cpsw_emac0 {
- phy_id = <&davinci_mdio>, <1>;
- phy-mode = "rgmii";
- dual_emac_res_vlan = <1>;
-};
-
-&cpsw_emac1 {
- phy_id = <&davinci_mdio>, <2>;
- phy-mode = "rgmii";
- dual_emac_res_vlan = <2>;
-};
-
-&davinci_mdio {
- pinctrl-names = "default", "sleep";
- pinctrl-0 = <&davinci_mdio_pins_default>;
- pinctrl-1 = <&davinci_mdio_pins_sleep>;
+&tpd12s015 {
+ gpios = <&gpio7 10 GPIO_ACTIVE_HIGH>, /* gpio7_10, CT CP HPD */
+ <&gpio6 28 GPIO_ACTIVE_HIGH>, /* gpio6_28, LS OE */
+ <&gpio7 12 GPIO_ACTIVE_HIGH>; /* gpio7_12/sp1_cs2, HPD */
};
&mmc1 {
- status = "okay";
-
- pinctrl-names = "default";
- pinctrl-0 = <&mmc1_pins_default>;
-
vmmc-supply = <&ldo1_reg>;
- bus-width = <4>;
- cd-gpios = <&gpio6 27 GPIO_ACTIVE_LOW>; /* gpio 219 */
-};
-
-&mmc2 {
- status = "okay";
-
- pinctrl-names = "default";
- pinctrl-0 = <&mmc2_pins_default>;
-
- vmmc-supply = <&vdd_3v3>;
- bus-width = <8>;
- ti,non-removable;
- cap-mmc-dual-data-rate;
-};
-
-&sata {
- status = "okay";
-};
-
-&usb2_phy1 {
- phy-supply = <&ldousb_reg>;
-};
-
-&usb2_phy2 {
- phy-supply = <&ldousb_reg>;
-};
-
-&usb1 {
- dr_mode = "host";
- pinctrl-names = "default";
- pinctrl-0 = <&usb1_pins>;
-};
-
-&omap_dwc3_2 {
- extcon = <&extcon_usb2>;
-};
-
-&usb2 {
- /*
- * Stand alone usage is peripheral only.
- * However, with some resistor modifications
- * this port can be used via expansion connectors
- * as "host" or "dual-role". If so, provide
- * the necessary dr_mode override in the expansion
- * board's DT.
- */
- dr_mode = "peripheral";
-};
-
-&cpu_trips {
- cpu_alert1: cpu_alert1 {
- temperature = <50000>; /* millicelsius */
- hysteresis = <2000>; /* millicelsius */
- type = "active";
- };
-};
-
-&cpu_cooling_maps {
- map1 {
- trip = <&cpu_alert1>;
- cooling-device = <&gpio_fan THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
- };
-};
-
-&thermal_zones {
- board_thermal: board_thermal {
- polling-delay-passive = <1250>; /* milliseconds */
- polling-delay = <1500>; /* milliseconds */
-
- /* sensor ID */
- thermal-sensors = <&tmp102 0>;
-
- board_trips: trips {
- board_alert0: board_alert {
- temperature = <40000>; /* millicelsius */
- hysteresis = <2000>; /* millicelsius */
- type = "active";
- };
-
- board_crit: board_crit {
- temperature = <105000>; /* millicelsius */
- hysteresis = <0>; /* millicelsius */
- type = "critical";
- };
- };
-
- board_cooling_maps: cooling-maps {
- map0 {
- trip = <&board_alert0>;
- cooling-device =
- <&gpio_fan THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
- };
- };
- };
-};
-
-&dss {
- status = "ok";
-
- vdda_video-supply = <&ldoln_reg>;
-};
-
-&hdmi {
- status = "ok";
- vdda-supply = <&ldo4_reg>;
-
- pinctrl-names = "default";
- pinctrl-0 = <&hdmi_pins>;
-
- port {
- hdmi_out: endpoint {
- remote-endpoint = <&tpd12s015_in>;
- };
- };
-};
-
-&pcie1 {
- gpios = <&gpio2 8 GPIO_ACTIVE_LOW>;
-};
-
-&mcasp3 {
- #sound-dai-cells = <0>;
- pinctrl-names = "default", "sleep";
- pinctrl-0 = <&mcasp3_pins_default>;
- pinctrl-1 = <&mcasp3_pins_sleep>;
- assigned-clocks = <&mcasp3_ahclkx_mux>;
- assigned-clock-parents = <&sys_clkin2>;
- status = "okay";
-
- op-mode = <0>; /* MCASP_IIS_MODE */
- tdm-slots = <2>;
- /* 4 serializers */
- serial-dir = < /* 0: INACTIVE, 1: TX, 2: RX */
- 1 2 0 0
- >;
- tx-num-evt = <32>;
- rx-num-evt = <32>;
-};
-
-&mailbox5 {
- status = "okay";
- mbox_ipu1_ipc3x: mbox_ipu1_ipc3x {
- status = "okay";
- };
- mbox_dsp1_ipc3x: mbox_dsp1_ipc3x {
- status = "okay";
- };
-};
-
-&mailbox6 {
- status = "okay";
- mbox_ipu2_ipc3x: mbox_ipu2_ipc3x {
- status = "okay";
- };
- mbox_dsp2_ipc3x: mbox_dsp2_ipc3x {
- status = "okay";
- };
};
diff --git a/arch/arm/boot/dts/dra7.dtsi b/arch/arm/boot/dts/dra7.dtsi
index 147df90..d4fcd68 100644
--- a/arch/arm/boot/dts/dra7.dtsi
+++ b/arch/arm/boot/dts/dra7.dtsi
@@ -80,9 +80,11 @@
compatible = "arm,cortex-a15";
reg = <0>;
- operating-points-v2 = <&cpu0_opp_table>;
- ti,syscon-efuse = <&scm_wkup 0x20c 0xf80000 19>;
- ti,syscon-rev = <&scm_wkup 0x204>;
+ operating-points = <
+ /* kHz uV */
+ 1000000 1060000
+ 1176000 1160000
+ >;
clocks = <&dpll_mpu_ck>;
clock-names = "cpu";
@@ -96,24 +98,6 @@
};
};
- cpu0_opp_table: opp_table0 {
- compatible = "operating-points-v2";
- opp-shared;
-
- opp_nom@1000000000 {
- opp-hz = /bits/ 64 <1000000000>;
- opp-microvolt = <1060000 850000 1150000>;
- opp-supported-hw = <0xFF 0x01>;
- opp-suspend;
- };
-
- opp_od@1176000000 {
- opp-hz = /bits/ 64 <1176000000>;
- opp-microvolt = <1160000 885000 1160000>;
- opp-supported-hw = <0xFF 0x02>;
- };
- };
-
/*
* The soc node represents the soc top level view. It is used for IPs
* that are not memory mapped in the MPU view or for the MPU itself.
diff --git a/arch/arm/boot/dts/dra74x.dtsi b/arch/arm/boot/dts/dra74x.dtsi
index 8987b3e..0a78347 100644
--- a/arch/arm/boot/dts/dra74x.dtsi
+++ b/arch/arm/boot/dts/dra74x.dtsi
@@ -17,7 +17,6 @@
device_type = "cpu";
compatible = "arm,cortex-a15";
reg = <1>;
- operating-points-v2 = <&cpu0_opp_table>;
};
};
diff --git a/arch/arm/boot/dts/omap3-gta04.dtsi b/arch/arm/boot/dts/omap3-gta04.dtsi
index 5563e25..b3a8b1f 100644
--- a/arch/arm/boot/dts/omap3-gta04.dtsi
+++ b/arch/arm/boot/dts/omap3-gta04.dtsi
@@ -102,7 +102,7 @@
backlight {
compatible = "pwm-backlight";
- pwms = <&pwm11 0 2000000 0>;
+ pwms = <&pwm11 0 12000000 0>;
pwm-names = "backlight";
brightness-levels = <0 11 20 30 40 50 60 70 80 90 100>;
default-brightness-level = <9>; /* => 90 */
diff --git a/arch/arm/boot/dts/omap4-panda-common.dtsi b/arch/arm/boot/dts/omap4-panda-common.dtsi
index d48e45b..1673689 100644
--- a/arch/arm/boot/dts/omap4-panda-common.dtsi
+++ b/arch/arm/boot/dts/omap4-panda-common.dtsi
@@ -446,6 +446,8 @@
pinctrl-names = "default";
pinctrl-0 = <&wl12xx_pins>;
vmmc-supply = <&wl12xx_vmmc>;
+ interrupts-extended = <&wakeupgen GIC_SPI 59 IRQ_TYPE_LEVEL_HIGH
+ &omap4_pmx_core 0x10e>;
non-removable;
bus-width = <4>;
cap-power-off-card;
diff --git a/arch/arm/boot/dts/omap5-board-common.dtsi b/arch/arm/boot/dts/omap5-board-common.dtsi
index d1f5ce3..6365635 100644
--- a/arch/arm/boot/dts/omap5-board-common.dtsi
+++ b/arch/arm/boot/dts/omap5-board-common.dtsi
@@ -77,16 +77,6 @@
reset-gpios = <&gpio3 15 GPIO_ACTIVE_LOW>; /* gpio3_79 ETH_NRESET */
};
- leds {
- compatible = "gpio-leds";
- led1 {
- label = "omap5:blue:usr1";
- gpios = <&gpio5 25 GPIO_ACTIVE_HIGH>; /* gpio5_153 D1 LED */
- linux,default-trigger = "heartbeat";
- default-state = "off";
- };
- };
-
tpd12s015: encoder {
compatible = "ti,tpd12s015";
@@ -332,7 +322,7 @@
wlcore_irq_pin: pinmux_wlcore_irq_pin {
pinctrl-single,pins = <
- OMAP5_IOPAD(0x40, PIN_INPUT_PULLUP | MUX_MODE6) /* llia_wakereqin.gpio1_wk14 */
+ OMAP5_IOPAD(0x40, PIN_INPUT | MUX_MODE6) /* llia_wakereqin.gpio1_wk14 */
>;
};
};
@@ -355,15 +345,17 @@
non-removable;
cap-power-off-card;
pinctrl-names = "default";
- pinctrl-0 = <&mmc3_pins &wlcore_irq_pin>;
- interrupts-extended = <&gic GIC_SPI 94 IRQ_TYPE_LEVEL_HIGH
- &omap5_pmx_core 0x168>;
+ pinctrl-0 = <&mmc3_pins>;
+ interrupts-extended = <&wakeupgen GIC_SPI 94 IRQ_TYPE_LEVEL_HIGH
+ &omap5_pmx_core 0x16a>;
#address-cells = <1>;
#size-cells = <0>;
wlcore: wlcore@2 {
compatible = "ti,wl1271";
reg = <2>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&wlcore_irq_pin>;
interrupt-parent = <&gpio1>;
interrupts = <14 IRQ_TYPE_LEVEL_HIGH>; /* gpio 14 */
ref-clock-frequency = <26000000>;
@@ -391,14 +383,23 @@
interrupt-controller;
#interrupt-cells = <2>;
ti,system-power-controller;
+ ti,mux-pad1 = <0xa1>;
+ ti,mux-pad2 = <0x1b>;
pinctrl-names = "default";
pinctrl-0 = <&palmas_sys_nirq_pins &palmas_msecure_pins>;
+ palmas_gpio: gpio {
+ compatible = "ti,palmas-gpio";
+ gpio-controller;
+ #gpio-cells = <2>;
+ };
+
extcon_usb3: palmas_usb {
compatible = "ti,palmas-usb-vid";
ti,enable-vbus-detection;
ti,enable-id-detection;
ti,wakeup;
+ id-gpios = <&palmas_gpio 0 GPIO_ACTIVE_HIGH>;
};
clk32kgaudio: palmas_clk32k@1 {
diff --git a/arch/arm/boot/dts/omap5-cm-t54.dts b/arch/arm/boot/dts/omap5-cm-t54.dts
index c9390fa..b153f60 100644
--- a/arch/arm/boot/dts/omap5-cm-t54.dts
+++ b/arch/arm/boot/dts/omap5-cm-t54.dts
@@ -13,7 +13,7 @@
memory@80000000 {
device_type = "memory";
- reg = <0x80000000 0x7F000000>; /* 2048 MB */
+ reg = <0 0x80000000 0 0x7f000000>; /* 2048 MB */
};
aliases {
diff --git a/arch/arm/boot/dts/omap5-igep0050.dts b/arch/arm/boot/dts/omap5-igep0050.dts
index 7aa2b0c..44e03b9 100644
--- a/arch/arm/boot/dts/omap5-igep0050.dts
+++ b/arch/arm/boot/dts/omap5-igep0050.dts
@@ -7,6 +7,7 @@
*/
/dts-v1/;
+#include <dt-bindings/input/input.h>
#include "omap5-board-common.dtsi"
/ {
@@ -15,7 +16,38 @@
memory@80000000 {
device_type = "memory";
- reg = <0x80000000 0x7f000000>; /* 2032 MB */
+ reg = <0x0 0x80000000 0 0x7f000000>; /* 2032 MB */
+ };
+
+ gpio_keys {
+ compatible = "gpio-keys";
+ pinctrl-0 = <&power_button_pin>;
+ pinctrl-names = "default";
+
+ power-button {
+ label = "Power Button";
+ linux,code = <KEY_POWER>;
+ gpios = <&gpio4 22 GPIO_ACTIVE_HIGH>;
+ };
+ };
+
+ leds {
+ compatible = "gpio-leds";
+ led@1 {
+ label = "board:green:usr0";
+ gpios = <&tca6416 1 0>;
+ default-state = "off";
+ };
+ led@2 {
+ label = "board:red:usr1";
+ gpios = <&tca6416 2 0>;
+ default-state = "off";
+ };
+ led@3 {
+ label = "board:blue:usr1";
+ gpios = <&tca6416 3 0>;
+ default-state = "off";
+ };
};
};
@@ -58,6 +90,12 @@
OMAP5_IOPAD(0x0fa, PIN_INPUT | MUX_MODE0) /* i2c4_sda */
>;
};
+
+ power_button_pin: pinctrl_power_button_pin {
+ pinctrl-single,pins = <
+ OMAP5_IOPAD(0x086, PIN_INPUT | MUX_MODE6) /* gpio4_118 */
+ >;
+ };
};
&tpd12s015 {
diff --git a/arch/arm/boot/dts/omap5-uevm.dts b/arch/arm/boot/dts/omap5-uevm.dts
index 5230ca0..53d31a8 100644
--- a/arch/arm/boot/dts/omap5-uevm.dts
+++ b/arch/arm/boot/dts/omap5-uevm.dts
@@ -15,7 +15,17 @@
memory@80000000 {
device_type = "memory";
- reg = <0x80000000 0x7F000000>; /* 2032 MB */
+ reg = <0 0x80000000 0 0x7f000000>; /* 2032 MB */
+ };
+
+ leds {
+ compatible = "gpio-leds";
+ led1 {
+ label = "omap5:blue:usr1";
+ gpios = <&gpio5 25 GPIO_ACTIVE_HIGH>; /* gpio5_153 D1 LED */
+ linux,default-trigger = "heartbeat";
+ default-state = "off";
+ };
};
};
@@ -61,3 +71,7 @@
OMAP5_IOPAD(0x1be, PIN_OUTPUT | MUX_MODE6) /* mcspi1_somi.gpio5_141 */
>;
};
+
+&wlcore {
+ compatible = "ti,wl1837";
+};
diff --git a/arch/arm/boot/dts/omap5.dtsi b/arch/arm/boot/dts/omap5.dtsi
index 71a8f54..2526211 100644
--- a/arch/arm/boot/dts/omap5.dtsi
+++ b/arch/arm/boot/dts/omap5.dtsi
@@ -12,8 +12,8 @@
#include <dt-bindings/pinctrl/omap.h>
/ {
- #address-cells = <1>;
- #size-cells = <1>;
+ #address-cells = <2>;
+ #size-cells = <2>;
compatible = "ti,omap5";
interrupt-parent = <&wakeupgen>;
@@ -90,10 +90,10 @@
compatible = "arm,cortex-a15-gic";
interrupt-controller;
#interrupt-cells = <3>;
- reg = <0x48211000 0x1000>,
- <0x48212000 0x1000>,
- <0x48214000 0x2000>,
- <0x48216000 0x2000>;
+ reg = <0 0x48211000 0 0x1000>,
+ <0 0x48212000 0 0x1000>,
+ <0 0x48214000 0 0x2000>,
+ <0 0x48216000 0 0x2000>;
interrupt-parent = <&gic>;
};
@@ -101,7 +101,7 @@
compatible = "ti,omap5-wugen-mpu", "ti,omap4-wugen-mpu";
interrupt-controller;
#interrupt-cells = <3>;
- reg = <0x48281000 0x1000>;
+ reg = <0 0x48281000 0 0x1000>;
interrupt-parent = <&gic>;
};
@@ -129,11 +129,11 @@
compatible = "ti,omap5-l3-noc", "simple-bus";
#address-cells = <1>;
#size-cells = <1>;
- ranges;
+ ranges = <0 0 0 0xc0000000>;
ti,hwmods = "l3_main_1", "l3_main_2", "l3_main_3";
- reg = <0x44000000 0x2000>,
- <0x44800000 0x3000>,
- <0x45000000 0x4000>;
+ reg = <0 0x44000000 0 0x2000>,
+ <0 0x44800000 0 0x3000>,
+ <0 0x45000000 0 0x4000>;
interrupts = <GIC_SPI 9 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 10 IRQ_TYPE_LEVEL_HIGH>;
@@ -863,7 +863,7 @@
#size-cells = <1>;
utmi-mode = <2>;
ranges;
- dwc3@4a030000 {
+ dwc3: dwc3@4a030000 {
compatible = "snps,dwc3";
reg = <0x4a030000 0x10000>;
interrupts = <GIC_SPI 92 IRQ_TYPE_LEVEL_HIGH>,
generated by cgit v0.10.2 at 2024-11-11 02:32:26 (GMT)