diff options
Diffstat (limited to 'arch/arm/mach-pxa')
84 files changed, 1952 insertions, 1194 deletions
diff --git a/arch/arm/mach-pxa/Kconfig b/arch/arm/mach-pxa/Kconfig index c93e73d..2fc9f94 100644 --- a/arch/arm/mach-pxa/Kconfig +++ b/arch/arm/mach-pxa/Kconfig @@ -50,6 +50,10 @@ config MACH_SAAR select PXA3xx select CPU_PXA930 +config MACH_SAARB + bool "PXA955 Handheld Platform (aka SAARB)" + select CPU_PXA955 + comment "Third Party Dev Platforms (sorted by vendor name)" config ARCH_PXA_IDP @@ -94,6 +98,7 @@ config MACH_ARMCORE select PXA27x select IWMMXT select PXA25x + select MIGHT_HAVE_PCI config MACH_EM_X270 bool "CompuLab EM-x270 platform" @@ -232,10 +237,6 @@ config MACH_COLIBRI bool "Toradex Colibri PXA270" select PXA27x -config MACH_COLIBRI_PXA270_EVALBOARD - bool "Toradex Colibri Evaluation Carrier Board support (PXA270)" - depends on MACH_COLIBRI - config MACH_COLIBRI_PXA270_INCOME bool "Income s.r.o. PXA270 SBC" depends on MACH_COLIBRI @@ -253,6 +254,10 @@ config MACH_COLIBRI320 select PXA3xx select CPU_PXA320 +config MACH_COLIBRI_EVALBOARD + bool "Toradex Colibri Evaluation Carrier Board support" + depends on MACH_COLIBRI || MACH_COLIBRI300 || MACH_COLIBRI320 + config MACH_VPAC270 bool "Voipac PXA270" select PXA27x @@ -652,11 +657,17 @@ config CPU_PXA935 help PXA935 (codename Tavor-P65) -config CPU_PXA950 +config PXA95x bool - select CPU_PXA930 + select CPU_PJ4 + help + Select code specific to PXA95x variants + +config CPU_PXA955 + bool + select PXA95x help - PXA950 (codename Tavor-PV2) + PXA950 (codename MG1) config PXA_SHARP_C7xx bool diff --git a/arch/arm/mach-pxa/Makefile b/arch/arm/mach-pxa/Makefile index e2f89c2..cc39d17 100644 --- a/arch/arm/mach-pxa/Makefile +++ b/arch/arm/mach-pxa/Makefile @@ -16,9 +16,10 @@ endif # Generic drivers that other drivers may depend upon # SoC-specific code -obj-$(CONFIG_PXA25x) += mfp-pxa2xx.o pxa2xx.o pxa25x.o -obj-$(CONFIG_PXA27x) += mfp-pxa2xx.o pxa2xx.o pxa27x.o -obj-$(CONFIG_PXA3xx) += mfp-pxa3xx.o pxa3xx.o smemc.o pxa3xx-ulpi.o +obj-$(CONFIG_PXA25x) += mfp-pxa2xx.o clock-pxa2xx.o pxa2xx.o pxa25x.o +obj-$(CONFIG_PXA27x) += mfp-pxa2xx.o clock-pxa2xx.o pxa2xx.o pxa27x.o +obj-$(CONFIG_PXA3xx) += mfp-pxa3xx.o clock-pxa3xx.o pxa3xx.o smemc.o pxa3xx-ulpi.o +obj-$(CONFIG_PXA95x) += mfp-pxa3xx.o clock-pxa3xx.o pxa95x.o smemc.o obj-$(CONFIG_CPU_PXA300) += pxa300.o obj-$(CONFIG_CPU_PXA320) += pxa320.o obj-$(CONFIG_CPU_PXA930) += pxa930.o @@ -34,6 +35,7 @@ obj-$(CONFIG_MACH_LITTLETON) += littleton.o obj-$(CONFIG_MACH_TAVOREVB) += tavorevb.o obj-$(CONFIG_MACH_TAVOREVB3) += tavorevb3.o obj-$(CONFIG_MACH_SAAR) += saar.o +obj-$(CONFIG_MACH_SAARB) += saarb.o # 3rd Party Dev Platforms obj-$(CONFIG_ARCH_PXA_IDP) += idp.o @@ -60,7 +62,7 @@ obj-$(CONFIG_MACH_LOGICPD_PXA270) += lpd270.o obj-$(CONFIG_MACH_PCM027) += pcm027.o obj-$(CONFIG_MACH_PCM990_BASEBOARD) += pcm990-baseboard.o obj-$(CONFIG_MACH_COLIBRI) += colibri-pxa270.o -obj-$(CONFIG_MACH_COLIBRI_PXA270_EVALBOARD) += colibri-pxa270-evalboard.o +obj-$(CONFIG_MACH_COLIBRI_EVALBOARD) += colibri-evalboard.o obj-$(CONFIG_MACH_COLIBRI_PXA270_INCOME) += colibri-pxa270-income.o obj-$(CONFIG_MACH_COLIBRI300) += colibri-pxa3xx.o colibri-pxa300.o obj-$(CONFIG_MACH_COLIBRI320) += colibri-pxa3xx.o colibri-pxa320.o diff --git a/arch/arm/mach-pxa/balloon3.c b/arch/arm/mach-pxa/balloon3.c index 21e1889..ccb2d0c 100644 --- a/arch/arm/mach-pxa/balloon3.c +++ b/arch/arm/mach-pxa/balloon3.c @@ -567,27 +567,29 @@ static inline void balloon3_i2c_init(void) {} * NAND ******************************************************************************/ #if defined(CONFIG_MTD_NAND_PLATFORM)||defined(CONFIG_MTD_NAND_PLATFORM_MODULE) -static uint16_t balloon3_ctl = - BALLOON3_NAND_CONTROL_FLCE0 | BALLOON3_NAND_CONTROL_FLCE1 | - BALLOON3_NAND_CONTROL_FLCE2 | BALLOON3_NAND_CONTROL_FLCE3 | - BALLOON3_NAND_CONTROL_FLWP; - static void balloon3_nand_cmd_ctl(struct mtd_info *mtd, int cmd, unsigned int ctrl) { struct nand_chip *this = mtd->priv; + uint8_t balloon3_ctl_set = 0, balloon3_ctl_clr = 0; if (ctrl & NAND_CTRL_CHANGE) { if (ctrl & NAND_CLE) - balloon3_ctl |= BALLOON3_NAND_CONTROL_FLCLE; + balloon3_ctl_set |= BALLOON3_NAND_CONTROL_FLCLE; else - balloon3_ctl &= ~BALLOON3_NAND_CONTROL_FLCLE; + balloon3_ctl_clr |= BALLOON3_NAND_CONTROL_FLCLE; if (ctrl & NAND_ALE) - balloon3_ctl |= BALLOON3_NAND_CONTROL_FLALE; + balloon3_ctl_set |= BALLOON3_NAND_CONTROL_FLALE; else - balloon3_ctl &= ~BALLOON3_NAND_CONTROL_FLALE; - - __raw_writel(balloon3_ctl, BALLOON3_NAND_CONTROL_REG); + balloon3_ctl_clr |= BALLOON3_NAND_CONTROL_FLALE; + + if (balloon3_ctl_clr) + __raw_writel(balloon3_ctl_clr, + BALLOON3_NAND_CONTROL_REG); + if (balloon3_ctl_set) + __raw_writel(balloon3_ctl_set, + BALLOON3_NAND_CONTROL_REG | + BALLOON3_FPGA_SETnCLR); } if (cmd != NAND_CMD_NONE) @@ -599,28 +601,33 @@ static void balloon3_nand_select_chip(struct mtd_info *mtd, int chip) if (chip < 0 || chip > 3) return; - balloon3_ctl |= BALLOON3_NAND_CONTROL_FLCE0 | - BALLOON3_NAND_CONTROL_FLCE1 | - BALLOON3_NAND_CONTROL_FLCE2 | - BALLOON3_NAND_CONTROL_FLCE3; + /* Assert all nCE lines */ + __raw_writew( + BALLOON3_NAND_CONTROL_FLCE0 | BALLOON3_NAND_CONTROL_FLCE1 | + BALLOON3_NAND_CONTROL_FLCE2 | BALLOON3_NAND_CONTROL_FLCE3, + BALLOON3_NAND_CONTROL_REG | BALLOON3_FPGA_SETnCLR); /* Deassert correct nCE line */ - balloon3_ctl &= ~(BALLOON3_NAND_CONTROL_FLCE0 << chip); + __raw_writew(BALLOON3_NAND_CONTROL_FLCE0 << chip, + BALLOON3_NAND_CONTROL_REG); +} - __raw_writew(balloon3_ctl, BALLOON3_NAND_CONTROL_REG); +static int balloon3_nand_dev_ready(struct mtd_info *mtd) +{ + return __raw_readl(BALLOON3_NAND_STAT_REG) & BALLOON3_NAND_STAT_RNB; } static int balloon3_nand_probe(struct platform_device *pdev) { - void __iomem *temp_map; uint16_t ver; int ret; - __raw_writew(BALLOON3_NAND_CONTROL2_16BIT, BALLOON3_NAND_CONTROL2_REG); + __raw_writew(BALLOON3_NAND_CONTROL2_16BIT, + BALLOON3_NAND_CONTROL2_REG | BALLOON3_FPGA_SETnCLR); ver = __raw_readw(BALLOON3_FPGA_VER); - if (ver > 0x0201) - pr_warn("The FPGA code, version 0x%04x, is newer than rel-0.3. " + if (ver < 0x4f08) + pr_warn("The FPGA code, version 0x%04x, is too old. " "NAND support might be broken in this version!", ver); /* Power up the NAND chips */ @@ -635,7 +642,11 @@ static int balloon3_nand_probe(struct platform_device *pdev) gpio_set_value(BALLOON3_GPIO_RUN_NAND, 1); /* Deassert all nCE lines and write protect line */ - __raw_writel(balloon3_ctl, BALLOON3_NAND_CONTROL_REG); + __raw_writel( + BALLOON3_NAND_CONTROL_FLCE0 | BALLOON3_NAND_CONTROL_FLCE1 | + BALLOON3_NAND_CONTROL_FLCE2 | BALLOON3_NAND_CONTROL_FLCE3 | + BALLOON3_NAND_CONTROL_FLWP, + BALLOON3_NAND_CONTROL_REG | BALLOON3_FPGA_SETnCLR); return 0; err2: @@ -677,7 +688,7 @@ struct platform_nand_data balloon3_nand_pdata = { }, .ctrl = { .hwcontrol = 0, - .dev_ready = 0, + .dev_ready = balloon3_nand_dev_ready, .select_chip = balloon3_nand_select_chip, .cmd_ctrl = balloon3_nand_cmd_ctl, .probe = balloon3_nand_probe, @@ -802,7 +813,7 @@ static struct map_desc balloon3_io_desc[] __initdata = { static void __init balloon3_map_io(void) { - pxa_map_io(); + pxa27x_map_io(); iotable_init(balloon3_io_desc, ARRAY_SIZE(balloon3_io_desc)); } diff --git a/arch/arm/mach-pxa/capc7117.c b/arch/arm/mach-pxa/capc7117.c index 4bd7a3c..4284513 100644 --- a/arch/arm/mach-pxa/capc7117.c +++ b/arch/arm/mach-pxa/capc7117.c @@ -149,7 +149,7 @@ static void __init capc7117_init(void) MACHINE_START(CAPC7117, "Embedian CAPC-7117 evaluation kit based on the MXM-8x10 CoM") .boot_params = 0xa0000100, - .map_io = pxa_map_io, + .map_io = pxa3xx_map_io, .init_irq = pxa3xx_init_irq, .timer = &pxa_timer, .init_machine = capc7117_init diff --git a/arch/arm/mach-pxa/clock-pxa2xx.c b/arch/arm/mach-pxa/clock-pxa2xx.c new file mode 100644 index 0000000..1ce0904 --- /dev/null +++ b/arch/arm/mach-pxa/clock-pxa2xx.c @@ -0,0 +1,64 @@ +/* + * linux/arch/arm/mach-pxa/clock-pxa2xx.c + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + */ + +#include <linux/module.h> +#include <linux/kernel.h> +#include <linux/init.h> +#include <linux/sysdev.h> + +#include <mach/pxa2xx-regs.h> + +#include "clock.h" + +void clk_pxa2xx_cken_enable(struct clk *clk) +{ + CKEN |= 1 << clk->cken; +} + +void clk_pxa2xx_cken_disable(struct clk *clk) +{ + CKEN &= ~(1 << clk->cken); +} + +const struct clkops clk_pxa2xx_cken_ops = { + .enable = clk_pxa2xx_cken_enable, + .disable = clk_pxa2xx_cken_disable, +}; + +#ifdef CONFIG_PM +static uint32_t saved_cken; + +static int pxa2xx_clock_suspend(struct sys_device *d, pm_message_t state) +{ + saved_cken = CKEN; + return 0; +} + +static int pxa2xx_clock_resume(struct sys_device *d) +{ + CKEN = saved_cken; + return 0; +} +#else +#define pxa2xx_clock_suspend NULL +#define pxa2xx_clock_resume NULL +#endif + +struct sysdev_class pxa2xx_clock_sysclass = { + .name = "pxa2xx-clock", + .suspend = pxa2xx_clock_suspend, + .resume = pxa2xx_clock_resume, +}; + +static int __init pxa2xx_clock_init(void) +{ + if (cpu_is_pxa2xx()) + return sysdev_class_register(&pxa2xx_clock_sysclass); + return 0; +} +postcore_initcall(pxa2xx_clock_init); diff --git a/arch/arm/mach-pxa/clock-pxa3xx.c b/arch/arm/mach-pxa/clock-pxa3xx.c new file mode 100644 index 0000000..1b08a34 --- /dev/null +++ b/arch/arm/mach-pxa/clock-pxa3xx.c @@ -0,0 +1,218 @@ +/* + * linux/arch/arm/mach-pxa/clock-pxa3xx.c + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + */ + +#include <linux/module.h> +#include <linux/kernel.h> +#include <linux/init.h> +#include <linux/io.h> + +#include <mach/smemc.h> +#include <mach/pxa3xx-regs.h> + +#include "clock.h" + +/* Crystal clock: 13MHz */ +#define BASE_CLK 13000000 + +/* Ring Oscillator Clock: 60MHz */ +#define RO_CLK 60000000 + +#define ACCR_D0CS (1 << 26) +#define ACCR_PCCE (1 << 11) + +/* crystal frequency to HSIO bus frequency multiplier (HSS) */ +static unsigned char hss_mult[4] = { 8, 12, 16, 24 }; + +/* + * Get the clock frequency as reflected by CCSR and the turbo flag. + * We assume these values have been applied via a fcs. + * If info is not 0 we also display the current settings. + */ +unsigned int pxa3xx_get_clk_frequency_khz(int info) +{ + unsigned long acsr, xclkcfg; + unsigned int t, xl, xn, hss, ro, XL, XN, CLK, HSS; + + /* Read XCLKCFG register turbo bit */ + __asm__ __volatile__("mrc\tp14, 0, %0, c6, c0, 0" : "=r"(xclkcfg)); + t = xclkcfg & 0x1; + + acsr = ACSR; + + xl = acsr & 0x1f; + xn = (acsr >> 8) & 0x7; + hss = (acsr >> 14) & 0x3; + + XL = xl * BASE_CLK; + XN = xn * XL; + + ro = acsr & ACCR_D0CS; + + CLK = (ro) ? RO_CLK : ((t) ? XN : XL); + HSS = (ro) ? RO_CLK : hss_mult[hss] * BASE_CLK; + + if (info) { + pr_info("RO Mode clock: %d.%02dMHz (%sactive)\n", + RO_CLK / 1000000, (RO_CLK % 1000000) / 10000, + (ro) ? "" : "in"); + pr_info("Run Mode clock: %d.%02dMHz (*%d)\n", + XL / 1000000, (XL % 1000000) / 10000, xl); + pr_info("Turbo Mode clock: %d.%02dMHz (*%d, %sactive)\n", + XN / 1000000, (XN % 1000000) / 10000, xn, + (t) ? "" : "in"); + pr_info("HSIO bus clock: %d.%02dMHz\n", + HSS / 1000000, (HSS % 1000000) / 10000); + } + + return CLK / 1000; +} + +/* + * Return the current AC97 clock frequency. + */ +static unsigned long clk_pxa3xx_ac97_getrate(struct clk *clk) +{ + unsigned long rate = 312000000; + unsigned long ac97_div; + + ac97_div = AC97_DIV; + + /* This may loose precision for some rates but won't for the + * standard 24.576MHz. + */ + rate /= (ac97_div >> 12) & 0x7fff; + rate *= (ac97_div & 0xfff); + + return rate; +} + +/* + * Return the current HSIO bus clock frequency + */ +static unsigned long clk_pxa3xx_hsio_getrate(struct clk *clk) +{ + unsigned long acsr; + unsigned int hss, hsio_clk; + + acsr = ACSR; + + hss = (acsr >> 14) & 0x3; + hsio_clk = (acsr & ACCR_D0CS) ? RO_CLK : hss_mult[hss] * BASE_CLK; + + return hsio_clk; +} + +/* crystal frequency to static memory controller multiplier (SMCFS) */ +static unsigned int smcfs_mult[8] = { 6, 0, 8, 0, 0, 16, }; +static unsigned int df_clkdiv[4] = { 1, 2, 4, 1 }; + +static unsigned long clk_pxa3xx_smemc_getrate(struct clk *clk) +{ + unsigned long acsr = ACSR; + unsigned long memclkcfg = __raw_readl(MEMCLKCFG); + unsigned int smcfs = (acsr >> 23) & 0x7; + + return BASE_CLK * smcfs_mult[(acsr >> 23) & 0x7] / + df_clkdiv[(memclkcfg >> 16) & 0x3]; +} + +void clk_pxa3xx_cken_enable(struct clk *clk) +{ + unsigned long mask = 1ul << (clk->cken & 0x1f); + + if (clk->cken < 32) + CKENA |= mask; + else + CKENB |= mask; +} + +void clk_pxa3xx_cken_disable(struct clk *clk) +{ + unsigned long mask = 1ul << (clk->cken & 0x1f); + + if (clk->cken < 32) + CKENA &= ~mask; + else + CKENB &= ~mask; +} + +const struct clkops clk_pxa3xx_cken_ops = { + .enable = clk_pxa3xx_cken_enable, + .disable = clk_pxa3xx_cken_disable, +}; + +const struct clkops clk_pxa3xx_hsio_ops = { + .enable = clk_pxa3xx_cken_enable, + .disable = clk_pxa3xx_cken_disable, + .getrate = clk_pxa3xx_hsio_getrate, +}; + +const struct clkops clk_pxa3xx_ac97_ops = { + .enable = clk_pxa3xx_cken_enable, + .disable = clk_pxa3xx_cken_disable, + .getrate = clk_pxa3xx_ac97_getrate, +}; + +const struct clkops clk_pxa3xx_smemc_ops = { + .enable = clk_pxa3xx_cken_enable, + .disable = clk_pxa3xx_cken_disable, + .getrate = clk_pxa3xx_smemc_getrate, +}; + +static void clk_pout_enable(struct clk *clk) +{ + OSCC |= OSCC_PEN; +} + +static void clk_pout_disable(struct clk *clk) +{ + OSCC &= ~OSCC_PEN; +} + +const struct clkops clk_pxa3xx_pout_ops = { + .enable = clk_pout_enable, + .disable = clk_pout_disable, +}; + +#ifdef CONFIG_PM +static uint32_t cken[2]; +static uint32_t accr; + +static int pxa3xx_clock_suspend(struct sys_device *d, pm_message_t state) +{ + cken[0] = CKENA; + cken[1] = CKENB; + accr = ACCR; + return 0; +} + +static int pxa3xx_clock_resume(struct sys_device *d) +{ + ACCR = accr; + CKENA = cken[0]; + CKENB = cken[1]; + return 0; +} +#else +#define pxa3xx_clock_suspend NULL +#define pxa3xx_clock_resume NULL +#endif + +struct sysdev_class pxa3xx_clock_sysclass = { + .name = "pxa3xx-clock", + .suspend = pxa3xx_clock_suspend, + .resume = pxa3xx_clock_resume, +}; + +static int __init pxa3xx_clock_init(void) +{ + if (cpu_is_pxa3xx() || cpu_is_pxa95x()) + return sysdev_class_register(&pxa3xx_clock_sysclass); + return 0; +} +postcore_initcall(pxa3xx_clock_init); diff --git a/arch/arm/mach-pxa/clock.c b/arch/arm/mach-pxa/clock.c index abba008..d515222 100644 --- a/arch/arm/mach-pxa/clock.c +++ b/arch/arm/mach-pxa/clock.c @@ -3,21 +3,11 @@ */ #include <linux/module.h> #include <linux/kernel.h> -#include <linux/list.h> -#include <linux/errno.h> -#include <linux/err.h> -#include <linux/string.h> #include <linux/clk.h> #include <linux/spinlock.h> -#include <linux/platform_device.h> #include <linux/delay.h> +#include <linux/clkdev.h> -#include <asm/clkdev.h> -#include <mach/pxa2xx-regs.h> -#include <mach/hardware.h> - -#include "devices.h" -#include "generic.h" #include "clock.h" static DEFINE_SPINLOCK(clocks_lock); @@ -63,18 +53,19 @@ unsigned long clk_get_rate(struct clk *clk) } EXPORT_SYMBOL(clk_get_rate); - -void clk_cken_enable(struct clk *clk) +void clk_dummy_enable(struct clk *clk) { - CKEN |= 1 << clk->cken; } -void clk_cken_disable(struct clk *clk) +void clk_dummy_disable(struct clk *clk) { - CKEN &= ~(1 << clk->cken); } -const struct clkops clk_cken_ops = { - .enable = clk_cken_enable, - .disable = clk_cken_disable, +const struct clkops clk_dummy_ops = { + .enable = clk_dummy_enable, + .disable = clk_dummy_disable, +}; + +struct clk clk_dummy = { + .ops = &clk_dummy_ops, }; diff --git a/arch/arm/mach-pxa/clock.h b/arch/arm/mach-pxa/clock.h index d848874..f9f349a 100644 --- a/arch/arm/mach-pxa/clock.h +++ b/arch/arm/mach-pxa/clock.h @@ -1,4 +1,5 @@ -#include <asm/clkdev.h> +#include <linux/clkdev.h> +#include <linux/sysdev.h> struct clkops { void (*enable)(struct clk *); @@ -14,6 +15,12 @@ struct clk { unsigned int enabled; }; +void clk_dummy_enable(struct clk *); +void clk_dummy_disable(struct clk *); + +extern const struct clkops clk_dummy_ops; +extern struct clk clk_dummy; + #define INIT_CLKREG(_clk,_devname,_conname) \ { \ .clk = _clk, \ @@ -21,14 +28,6 @@ struct clk { .con_id = _conname, \ } -#define DEFINE_CKEN(_name, _cken, _rate, _delay) \ -struct clk clk_##_name = { \ - .ops = &clk_cken_ops, \ - .rate = _rate, \ - .cken = CKEN_##_cken, \ - .delay = _delay, \ - } - #define DEFINE_CK(_name, _cken, _ops) \ struct clk clk_##_name = { \ .ops = _ops, \ @@ -42,28 +41,38 @@ struct clk clk_##_name = { \ .delay = _delay, \ } -extern const struct clkops clk_cken_ops; - -void clk_cken_enable(struct clk *clk); -void clk_cken_disable(struct clk *clk); - -#ifdef CONFIG_PXA3xx -#define DEFINE_PXA3_CKEN(_name, _cken, _rate, _delay) \ +#define DEFINE_PXA2_CKEN(_name, _cken, _rate, _delay) \ struct clk clk_##_name = { \ - .ops = &clk_pxa3xx_cken_ops, \ + .ops = &clk_pxa2xx_cken_ops, \ .rate = _rate, \ .cken = CKEN_##_cken, \ .delay = _delay, \ } -#define DEFINE_PXA3_CK(_name, _cken, _ops) \ +extern const struct clkops clk_pxa2xx_cken_ops; + +void clk_pxa2xx_cken_enable(struct clk *clk); +void clk_pxa2xx_cken_disable(struct clk *clk); + +extern struct sysdev_class pxa2xx_clock_sysclass; + +#if defined(CONFIG_PXA3xx) || defined(CONFIG_PXA95x) +#define DEFINE_PXA3_CKEN(_name, _cken, _rate, _delay) \ struct clk clk_##_name = { \ - .ops = _ops, \ + .ops = &clk_pxa3xx_cken_ops, \ + .rate = _rate, \ .cken = CKEN_##_cken, \ + .delay = _delay, \ } extern const struct clkops clk_pxa3xx_cken_ops; +extern const struct clkops clk_pxa3xx_hsio_ops; +extern const struct clkops clk_pxa3xx_ac97_ops; +extern const struct clkops clk_pxa3xx_pout_ops; +extern const struct clkops clk_pxa3xx_smemc_ops; + extern void clk_pxa3xx_cken_enable(struct clk *); extern void clk_pxa3xx_cken_disable(struct clk *); -#endif +extern struct sysdev_class pxa3xx_clock_sysclass; +#endif diff --git a/arch/arm/mach-pxa/cm-x255.c b/arch/arm/mach-pxa/cm-x255.c index f1a7703..93f59f8 100644 --- a/arch/arm/mach-pxa/cm-x255.c +++ b/arch/arm/mach-pxa/cm-x255.c @@ -17,13 +17,13 @@ #include <linux/mtd/nand-gpio.h> #include <linux/spi/spi.h> +#include <linux/spi/pxa2xx_spi.h> #include <asm/mach/arch.h> #include <asm/mach-types.h> #include <asm/mach/map.h> #include <mach/pxa25x.h> -#include <mach/pxa2xx_spi.h> #include "generic.h" diff --git a/arch/arm/mach-pxa/cm-x270.c b/arch/arm/mach-pxa/cm-x270.c index a9926bb..b88d601a 100644 --- a/arch/arm/mach-pxa/cm-x270.c +++ b/arch/arm/mach-pxa/cm-x270.c @@ -19,12 +19,12 @@ #include <video/mbxfb.h> #include <linux/spi/spi.h> +#include <linux/spi/pxa2xx_spi.h> #include <linux/spi/libertas_spi.h> #include <mach/pxa27x.h> #include <mach/ohci.h> #include <mach/mmc.h> -#include <mach/pxa2xx_spi.h> #include "generic.h" diff --git a/arch/arm/mach-pxa/cm-x2xx.c b/arch/arm/mach-pxa/cm-x2xx.c index d34b99f..b734d84 100644 --- a/arch/arm/mach-pxa/cm-x2xx.c +++ b/arch/arm/mach-pxa/cm-x2xx.c @@ -24,6 +24,7 @@ #include <mach/pxa2xx-regs.h> #include <mach/audio.h> #include <mach/pxafb.h> +#include <mach/smemc.h> #include <asm/hardware/it8152.h> @@ -392,9 +393,9 @@ static int cmx2xx_suspend(struct sys_device *dev, pm_message_t state) cmx2xx_pci_suspend(); /* save MSC registers */ - sleep_save_msc[0] = MSC0; - sleep_save_msc[1] = MSC1; - sleep_save_msc[2] = MSC2; + sleep_save_msc[0] = __raw_readl(MSC0); + sleep_save_msc[1] = __raw_readl(MSC1); + sleep_save_msc[2] = __raw_readl(MSC2); /* setup power saving mode registers */ PCFR = 0x0; @@ -416,9 +417,9 @@ static int cmx2xx_resume(struct sys_device *dev) cmx2xx_pci_resume(); /* restore MSC registers */ - MSC0 = sleep_save_msc[0]; - MSC1 = sleep_save_msc[1]; - MSC2 = sleep_save_msc[2]; + __raw_writel(sleep_save_msc[0], MSC0); + __raw_writel(sleep_save_msc[1], MSC1); + __raw_writel(sleep_save_msc[2], MSC2); return 0; } @@ -498,7 +499,12 @@ static struct map_desc cmx2xx_io_desc[] __initdata = { static void __init cmx2xx_map_io(void) { - pxa_map_io(); + if (cpu_is_pxa25x()) + pxa25x_map_io(); + + if (cpu_is_pxa27x()) + pxa27x_map_io(); + iotable_init(cmx2xx_io_desc, ARRAY_SIZE(cmx2xx_io_desc)); it8152_base_address = CMX2XX_IT8152_VIRT; @@ -506,7 +512,11 @@ static void __init cmx2xx_map_io(void) #else static void __init cmx2xx_map_io(void) { - pxa_map_io(); + if (cpu_is_pxa25x()) + pxa25x_map_io(); + + if (cpu_is_pxa27x()) + pxa27x_map_io(); } #endif diff --git a/arch/arm/mach-pxa/cm-x300.c b/arch/arm/mach-pxa/cm-x300.c index 922b107..7984268 100644 --- a/arch/arm/mach-pxa/cm-x300.c +++ b/arch/arm/mach-pxa/cm-x300.c @@ -857,7 +857,7 @@ static void __init cm_x300_fixup(struct machine_desc *mdesc, struct tag *tags, MACHINE_START(CM_X300, "CM-X300 module") .boot_params = 0xa0000100, - .map_io = pxa_map_io, + .map_io = pxa3xx_map_io, .init_irq = pxa3xx_init_irq, .timer = &pxa_timer, .init_machine = cm_x300_init, diff --git a/arch/arm/mach-pxa/colibri-pxa270-evalboard.c b/arch/arm/mach-pxa/colibri-evalboard.c index 0f3b632..6b2c800 100644 --- a/arch/arm/mach-pxa/colibri-pxa270-evalboard.c +++ b/arch/arm/mach-pxa/colibri-evalboard.c @@ -1,7 +1,7 @@ /* - * linux/arch/arm/mach-pxa/colibri-pxa270-evalboard.c + * linux/arch/arm/mach-pxa/colibri-evalboard.c * - * Support for Toradex PXA270 based Colibri Evaluation Carrier Board + * Support for Toradex Colibri Evaluation Carrier Board * Daniel Mack <daniel@caiaq.de> * Marek Vasut <marek.vasut@gmail.com> * @@ -19,6 +19,7 @@ #include <asm/mach-types.h> #include <mach/hardware.h> #include <asm/mach/arch.h> +#include <linux/i2c.h> #include <mach/pxa27x.h> #include <mach/colibri.h> @@ -26,86 +27,95 @@ #include <mach/ohci.h> #include <mach/pxa27x-udc.h> +#include <plat/i2c.h> + #include "generic.h" #include "devices.h" /****************************************************************************** - * Pin configuration - ******************************************************************************/ -static mfp_cfg_t colibri_pxa270_evalboard_pin_config[] __initdata = { - /* MMC */ - GPIO32_MMC_CLK, - GPIO92_MMC_DAT_0, - GPIO109_MMC_DAT_1, - GPIO110_MMC_DAT_2, - GPIO111_MMC_DAT_3, - GPIO112_MMC_CMD, - GPIO0_GPIO, /* SD detect */ - - /* FFUART */ - GPIO39_FFUART_TXD, - GPIO34_FFUART_RXD, - - /* UHC */ - GPIO88_USBH1_PWR, - GPIO89_USBH1_PEN, - GPIO119_USBH2_PWR, - GPIO120_USBH2_PEN, -}; - -/****************************************************************************** * SD/MMC card controller ******************************************************************************/ #if defined(CONFIG_MMC_PXA) || defined(CONFIG_MMC_PXA_MODULE) -static struct pxamci_platform_data colibri_pxa270_mci_platform_data = { +static struct pxamci_platform_data colibri_mci_platform_data = { .ocr_mask = MMC_VDD_32_33 | MMC_VDD_33_34, .gpio_power = -1, - .gpio_card_detect = GPIO0_COLIBRI_PXA270_SD_DETECT, .gpio_card_ro = -1, .detect_delay_ms = 200, }; -static void __init colibri_pxa270_mmc_init(void) +static void __init colibri_mmc_init(void) { - pxa_set_mci_info(&colibri_pxa270_mci_platform_data); + if (machine_is_colibri()) /* PXA270 Colibri */ + colibri_mci_platform_data.gpio_card_detect = + GPIO0_COLIBRI_PXA270_SD_DETECT; + if (machine_is_colibri300()) /* PXA300 Colibri */ + colibri_mci_platform_data.gpio_card_detect = + GPIO39_COLIBRI_PXA300_SD_DETECT; + else /* PXA320 Colibri */ + colibri_mci_platform_data.gpio_card_detect = + GPIO28_COLIBRI_PXA320_SD_DETECT; + + pxa_set_mci_info(&colibri_mci_platform_data); } #else -static inline void colibri_pxa270_mmc_init(void) {} +static inline void colibri_mmc_init(void) {} #endif /****************************************************************************** * USB Host ******************************************************************************/ #if defined(CONFIG_USB_OHCI_HCD) || defined(CONFIG_USB_OHCI_HCD_MODULE) -static int colibri_pxa270_ohci_init(struct device *dev) +static int colibri_ohci_init(struct device *dev) { UP2OCR = UP2OCR_HXS | UP2OCR_HXOE | UP2OCR_DPPDE | UP2OCR_DMPDE; return 0; } -static struct pxaohci_platform_data colibri_pxa270_ohci_info = { +static struct pxaohci_platform_data colibri_ohci_info = { .port_mode = PMM_PERPORT_MODE, - .flags = ENABLE_PORT1 | ENABLE_PORT2 | + .flags = ENABLE_PORT1 | POWER_CONTROL_LOW | POWER_SENSE_LOW, - .init = colibri_pxa270_ohci_init, + .init = colibri_ohci_init, }; -static void __init colibri_pxa270_uhc_init(void) +static void __init colibri_uhc_init(void) { - pxa_set_ohci_info(&colibri_pxa270_ohci_info); + /* Colibri PXA270 has two usb ports, TBA for 320 */ + if (machine_is_colibri()) + colibri_ohci_info.flags |= ENABLE_PORT2; + + pxa_set_ohci_info(&colibri_ohci_info); } #else -static inline void colibri_pxa270_uhc_init(void) {} +static inline void colibri_uhc_init(void) {} #endif -void __init colibri_pxa270_evalboard_init(void) +/****************************************************************************** + * I2C RTC + ******************************************************************************/ +#if defined(CONFIG_RTC_DRV_DS1307) || defined(CONFIG_RTC_DRV_DS1307_MODULE) +static struct i2c_board_info __initdata colibri_i2c_devs[] = { + { + I2C_BOARD_INFO("m41t00", 0x68), + }, +}; + +static void __init colibri_rtc_init(void) +{ + pxa_set_i2c_info(NULL); + i2c_register_board_info(0, ARRAY_AND_SIZE(colibri_i2c_devs)); +} +#else +static inline void colibri_rtc_init(void) {} +#endif + +void __init colibri_evalboard_init(void) { - pxa2xx_mfp_config(ARRAY_AND_SIZE(colibri_pxa270_evalboard_pin_config)); pxa_set_ffuart_info(NULL); pxa_set_btuart_info(NULL); pxa_set_stuart_info(NULL); - colibri_pxa270_mmc_init(); - colibri_pxa270_uhc_init(); + colibri_mmc_init(); + colibri_uhc_init(); + colibri_rtc_init(); } - diff --git a/arch/arm/mach-pxa/colibri-pxa270-income.c b/arch/arm/mach-pxa/colibri-pxa270-income.c index 37f0f3e..07b62a0 100644 --- a/arch/arm/mach-pxa/colibri-pxa270-income.c +++ b/arch/arm/mach-pxa/colibri-pxa270-income.c @@ -46,52 +46,6 @@ #define GPIO113_INCOME_TS_IRQ (113) /****************************************************************************** - * Pin configuration - ******************************************************************************/ -static mfp_cfg_t income_pin_config[] __initdata = { - /* MMC */ - GPIO32_MMC_CLK, - GPIO92_MMC_DAT_0, - GPIO109_MMC_DAT_1, - GPIO110_MMC_DAT_2, - GPIO111_MMC_DAT_3, - GPIO112_MMC_CMD, - GPIO0_GPIO, /* SD detect */ - GPIO1_GPIO, /* SD read-only */ - - /* FFUART */ - GPIO39_FFUART_TXD, - GPIO34_FFUART_RXD, - - /* BFUART */ - GPIO42_BTUART_RXD, - GPIO43_BTUART_TXD, - GPIO45_BTUART_RTS, - - /* STUART */ - GPIO46_STUART_RXD, - GPIO47_STUART_TXD, - - /* UHC */ - GPIO88_USBH1_PWR, - GPIO89_USBH1_PEN, - - /* LCD */ - GPIOxx_LCD_TFT_16BPP, - - /* PWM */ - GPIO16_PWM0_OUT, - - /* I2C */ - GPIO117_I2C_SCL, - GPIO118_I2C_SDA, - - /* LED */ - GPIO54_GPIO, /* LED A */ - GPIO55_GPIO, /* LED B */ -}; - -/****************************************************************************** * SD/MMC card controller ******************************************************************************/ #if defined(CONFIG_MMC_PXA) || defined(CONFIG_MMC_PXA_MODULE) @@ -257,7 +211,6 @@ static inline void income_pwm_init(void) {} void __init colibri_pxa270_income_boardinit(void) { - pxa2xx_mfp_config(ARRAY_AND_SIZE(income_pin_config)); pxa_set_ffuart_info(NULL); pxa_set_btuart_info(NULL); pxa_set_stuart_info(NULL); diff --git a/arch/arm/mach-pxa/colibri-pxa270.c b/arch/arm/mach-pxa/colibri-pxa270.c index bc04510..6fc5d32 100644 --- a/arch/arm/mach-pxa/colibri-pxa270.c +++ b/arch/arm/mach-pxa/colibri-pxa270.c @@ -33,6 +33,103 @@ #include "generic.h" /****************************************************************************** + * Evaluation board MFP + ******************************************************************************/ +#ifdef CONFIG_MACH_COLIBRI_EVALBOARD +static mfp_cfg_t colibri_pxa270_evalboard_pin_config[] __initdata = { + /* MMC */ + GPIO32_MMC_CLK, + GPIO92_MMC_DAT_0, + GPIO109_MMC_DAT_1, + GPIO110_MMC_DAT_2, + GPIO111_MMC_DAT_3, + GPIO112_MMC_CMD, + GPIO0_GPIO, /* SD detect */ + + /* FFUART */ + GPIO39_FFUART_TXD, + GPIO34_FFUART_RXD, + + /* UHC */ + GPIO88_USBH1_PWR, + GPIO89_USBH1_PEN, + GPIO119_USBH2_PWR, + GPIO120_USBH2_PEN, + + /* PCMCIA */ + GPIO85_nPCE_1, + GPIO54_nPCE_2, + GPIO55_nPREG, + GPIO50_nPIOR, + GPIO51_nPIOW, + GPIO49_nPWE, + GPIO48_nPOE, + GPIO57_nIOIS16, + GPIO56_nPWAIT, + GPIO104_PSKTSEL, + GPIO53_GPIO, /* RESET */ + GPIO83_GPIO, /* BVD1 */ + GPIO82_GPIO, /* BVD2 */ + GPIO1_GPIO, /* READY */ + GPIO84_GPIO, /* DETECT */ + GPIO107_GPIO, /* PPEN */ + + /* I2C */ + GPIO117_I2C_SCL, + GPIO118_I2C_SDA, +}; +#else +static mfp_cfg_t colibri_pxa270_evalboard_pin_config[] __initdata = {}; +#endif + +#ifdef CONFIG_MACH_COLIBRI_PXA270_INCOME +static mfp_cfg_t income_pin_config[] __initdata = { + /* MMC */ + GPIO32_MMC_CLK, + GPIO92_MMC_DAT_0, + GPIO109_MMC_DAT_1, + GPIO110_MMC_DAT_2, + GPIO111_MMC_DAT_3, + GPIO112_MMC_CMD, + GPIO0_GPIO, /* SD detect */ + GPIO1_GPIO, /* SD read-only */ + + /* FFUART */ + GPIO39_FFUART_TXD, + GPIO34_FFUART_RXD, + + /* BFUART */ + GPIO42_BTUART_RXD, + GPIO43_BTUART_TXD, + GPIO45_BTUART_RTS, + + /* STUART */ + GPIO46_STUART_RXD, + GPIO47_STUART_TXD, + + /* UHC */ + GPIO88_USBH1_PWR, + GPIO89_USBH1_PEN, + + /* LCD */ + GPIOxx_LCD_TFT_16BPP, + + /* PWM */ + GPIO16_PWM0_OUT, + + /* I2C */ + GPIO117_I2C_SCL, + GPIO118_I2C_SDA, + + /* LED */ + GPIO54_GPIO, /* LED A */ + GPIO55_GPIO, /* LED B */ +}; +#else +static mfp_cfg_t income_pin_config[] __initdata = {}; +#endif + +/****************************************************************************** * Pin configuration ******************************************************************************/ static mfp_cfg_t colibri_pxa270_pin_config[] __initdata = { @@ -184,10 +281,13 @@ static void __init colibri_pxa270_init(void) colibri_pxa270_tsc_init(); switch (colibri_pxa270_baseboard) { - case COLIBRI_PXA270_EVALBOARD: - colibri_pxa270_evalboard_init(); + case COLIBRI_EVALBOARD: + pxa2xx_mfp_config(ARRAY_AND_SIZE( + colibri_pxa270_evalboard_pin_config)); + colibri_evalboard_init(); break; case COLIBRI_PXA270_INCOME: + pxa2xx_mfp_config(ARRAY_AND_SIZE(income_pin_config)); colibri_pxa270_income_boardinit(); break; default: @@ -209,7 +309,7 @@ static void __init colibri_pxa270_income_init(void) MACHINE_START(COLIBRI, "Toradex Colibri PXA270") .boot_params = COLIBRI_SDRAM_BASE + 0x100, .init_machine = colibri_pxa270_init, - .map_io = pxa_map_io, + .map_io = pxa27x_map_io, .init_irq = pxa27x_init_irq, .timer = &pxa_timer, MACHINE_END @@ -217,7 +317,7 @@ MACHINE_END MACHINE_START(INCOME, "Income s.r.o. SH-Dmaster PXA270 SBC") .boot_params = 0xa0000100, .init_machine = colibri_pxa270_income_init, - .map_io = pxa_map_io, + .map_io = pxa27x_map_io, .init_irq = pxa27x_init_irq, .timer = &pxa_timer, MACHINE_END diff --git a/arch/arm/mach-pxa/colibri-pxa300.c b/arch/arm/mach-pxa/colibri-pxa300.c index a70b256..fddb16d 100644 --- a/arch/arm/mach-pxa/colibri-pxa300.c +++ b/arch/arm/mach-pxa/colibri-pxa300.c @@ -31,9 +31,38 @@ #include "generic.h" #include "devices.h" + +#ifdef CONFIG_MACH_COLIBRI_EVALBOARD +static mfp_cfg_t colibri_pxa300_evalboard_pin_config[] __initdata = { + /* MMC */ + GPIO7_MMC1_CLK, + GPIO14_MMC1_CMD, + GPIO3_MMC1_DAT0, + GPIO4_MMC1_DAT1, + GPIO5_MMC1_DAT2, + GPIO6_MMC1_DAT3, + GPIO39_GPIO, /* SD detect */ + + /* UHC */ + GPIO0_2_USBH_PEN, + GPIO1_2_USBH_PWR, + GPIO77_USB_P3_1, + GPIO78_USB_P3_2, + GPIO79_USB_P3_3, + GPIO80_USB_P3_4, + GPIO81_USB_P3_5, + GPIO82_USB_P3_6, + + /* I2C */ + GPIO21_I2C_SCL, + GPIO22_I2C_SDA, +}; +#else +static mfp_cfg_t colibri_pxa300_evalboard_pin_config[] __initdata = {}; +#endif + #if defined(CONFIG_AX88796) #define COLIBRI_ETH_IRQ_GPIO mfp_to_gpio(GPIO26_GPIO) - /* * Asix AX88796 Ethernet */ @@ -80,35 +109,6 @@ static void __init colibri_pxa300_init_eth(void) static inline void __init colibri_pxa300_init_eth(void) {} #endif /* CONFIG_AX88796 */ -#if defined(CONFIG_USB_OHCI_HCD) || defined(CONFIG_USB_OHCI_HCD_MODULE) -static mfp_cfg_t colibri_pxa300_usb_pin_config[] __initdata = { - GPIO0_2_USBH_PEN, - GPIO1_2_USBH_PWR, -}; - -static struct pxaohci_platform_data colibri_pxa300_ohci_info = { - .port_mode = PMM_GLOBAL_MODE, - .flags = ENABLE_PORT1 | POWER_CONTROL_LOW | POWER_SENSE_LOW, -}; - -void __init colibri_pxa300_init_ohci(void) -{ - pxa3xx_mfp_config(ARRAY_AND_SIZE(colibri_pxa300_usb_pin_config)); - pxa_set_ohci_info(&colibri_pxa300_ohci_info); -} -#else -static inline void colibri_pxa300_init_ohci(void) {} -#endif /* CONFIG_USB_OHCI_HCD || CONFIG_USB_OHCI_HCD_MODULE */ - -static mfp_cfg_t colibri_pxa300_mmc_pin_config[] __initdata = { - GPIO7_MMC1_CLK, - GPIO14_MMC1_CMD, - GPIO3_MMC1_DAT0, - GPIO4_MMC1_DAT1, - GPIO5_MMC1_DAT2, - GPIO6_MMC1_DAT3, -}; - #if defined(CONFIG_FB_PXA) || defined(CONFIG_FB_PXA_MODULE) static mfp_cfg_t colibri_pxa300_lcd_pin_config[] __initdata = { GPIO54_LCD_LDD_0, @@ -171,24 +171,21 @@ static inline void colibri_pxa310_init_ac97(void) {} void __init colibri_pxa300_init(void) { - pxa_set_ffuart_info(NULL); - pxa_set_btuart_info(NULL); - pxa_set_stuart_info(NULL); - colibri_pxa300_init_eth(); - colibri_pxa300_init_ohci(); colibri_pxa3xx_init_nand(); colibri_pxa300_init_lcd(); colibri_pxa3xx_init_lcd(mfp_to_gpio(GPIO39_GPIO)); colibri_pxa310_init_ac97(); - colibri_pxa3xx_init_mmc(ARRAY_AND_SIZE(colibri_pxa300_mmc_pin_config), - mfp_to_gpio(MFP_PIN_GPIO13)); + + /* Evalboard init */ + pxa3xx_mfp_config(ARRAY_AND_SIZE(colibri_pxa300_evalboard_pin_config)); + colibri_evalboard_init(); } MACHINE_START(COLIBRI300, "Toradex Colibri PXA300") .boot_params = COLIBRI_SDRAM_BASE + 0x100, .init_machine = colibri_pxa300_init, - .map_io = pxa_map_io, + .map_io = pxa3xx_map_io, .init_irq = pxa3xx_init_irq, .timer = &pxa_timer, MACHINE_END diff --git a/arch/arm/mach-pxa/colibri-pxa320.c b/arch/arm/mach-pxa/colibri-pxa320.c index ca5f29e..ff9ff5f 100644 --- a/arch/arm/mach-pxa/colibri-pxa320.c +++ b/arch/arm/mach-pxa/colibri-pxa320.c @@ -35,9 +35,72 @@ #include "generic.h" #include "devices.h" +#ifdef CONFIG_MACH_COLIBRI_EVALBOARD +static mfp_cfg_t colibri_pxa320_evalboard_pin_config[] __initdata = { + /* MMC */ + GPIO22_MMC1_CLK, + GPIO23_MMC1_CMD, + GPIO18_MMC1_DAT0, + GPIO19_MMC1_DAT1, + GPIO20_MMC1_DAT2, + GPIO21_MMC1_DAT3, + GPIO28_GPIO, /* SD detect */ + + /* UART 1 configuration (may be set by bootloader) */ + GPIO99_UART1_CTS, + GPIO104_UART1_RTS, + GPIO97_UART1_RXD, + GPIO98_UART1_TXD, + GPIO101_UART1_DTR, + GPIO103_UART1_DSR, + GPIO100_UART1_DCD, + GPIO102_UART1_RI, + + /* UART 2 configuration */ + GPIO109_UART2_CTS, + GPIO112_UART2_RTS, + GPIO110_UART2_RXD, + GPIO111_UART2_TXD, + + /* UART 3 configuration */ + GPIO30_UART3_RXD, + GPIO31_UART3_TXD, + + /* UHC */ + GPIO2_2_USBH_PEN, + GPIO3_2_USBH_PWR, + + /* I2C */ + GPIO32_I2C_SCL, + GPIO33_I2C_SDA, + + /* PCMCIA */ + MFP_CFG(GPIO59, AF7), /* PRST ; AF7 to tristate */ + MFP_CFG(GPIO61, AF7), /* PCE1 ; AF7 to tristate */ + MFP_CFG(GPIO60, AF7), /* PCE2 ; AF7 to tristate */ + MFP_CFG(GPIO62, AF7), /* PCD ; AF7 to tristate */ + MFP_CFG(GPIO56, AF7), /* PSKTSEL ; AF7 to tristate */ + GPIO27_GPIO, /* RDnWR ; input/tristate */ + GPIO50_GPIO, /* PREG ; input/tristate */ + GPIO2_RDY, + GPIO5_NPIOR, + GPIO6_NPIOW, + GPIO7_NPIOS16, + GPIO8_NPWAIT, + GPIO29_GPIO, /* PRDY (READY GPIO) */ + GPIO57_GPIO, /* PPEN (POWER GPIO) */ + GPIO81_GPIO, /* PCD (DETECT GPIO) */ + GPIO77_GPIO, /* PRST (RESET GPIO) */ + GPIO53_GPIO, /* PBVD1 */ + GPIO79_GPIO, /* PBVD2 */ + GPIO54_GPIO, /* POE */ +}; +#else +static mfp_cfg_t colibri_pxa320_evalboard_pin_config[] __initdata = {}; +#endif + #if defined(CONFIG_AX88796) #define COLIBRI_ETH_IRQ_GPIO mfp_to_gpio(GPIO36_GPIO) - /* * Asix AX88796 Ethernet */ @@ -84,26 +147,6 @@ static void __init colibri_pxa320_init_eth(void) static inline void __init colibri_pxa320_init_eth(void) {} #endif /* CONFIG_AX88796 */ -#if defined(CONFIG_USB_OHCI_HCD) || defined(CONFIG_USB_OHCI_HCD_MODULE) -static mfp_cfg_t colibri_pxa320_usb_pin_config[] __initdata = { - GPIO2_2_USBH_PEN, - GPIO3_2_USBH_PWR, -}; - -static struct pxaohci_platform_data colibri_pxa320_ohci_info = { - .port_mode = PMM_GLOBAL_MODE, - .flags = ENABLE_PORT1 | POWER_CONTROL_LOW | POWER_SENSE_LOW, -}; - -void __init colibri_pxa320_init_ohci(void) -{ - pxa3xx_mfp_config(ARRAY_AND_SIZE(colibri_pxa320_usb_pin_config)); - pxa_set_ohci_info(&colibri_pxa320_ohci_info); -} -#else -static inline void colibri_pxa320_init_ohci(void) {} -#endif /* CONFIG_USB_OHCI_HCD || CONFIG_USB_OHCI_HCD_MODULE */ - #if defined(CONFIG_USB_GADGET_PXA27X)||defined(CONFIG_USB_GADGET_PXA27X_MODULE) static struct gpio_vbus_mach_info colibri_pxa320_gpio_vbus_info = { .gpio_vbus = mfp_to_gpio(MFP_PIN_GPIO96), @@ -140,15 +183,6 @@ static void __init colibri_pxa320_init_udc(void) static inline void colibri_pxa320_init_udc(void) {} #endif -static mfp_cfg_t colibri_pxa320_mmc_pin_config[] __initdata = { - GPIO22_MMC1_CLK, - GPIO23_MMC1_CMD, - GPIO18_MMC1_DAT0, - GPIO19_MMC1_DAT1, - GPIO20_MMC1_DAT2, - GPIO21_MMC1_DAT3 -}; - #if defined(CONFIG_FB_PXA) || defined(CONFIG_FB_PXA_MODULE) static mfp_cfg_t colibri_pxa320_lcd_pin_config[] __initdata = { GPIO6_2_LCD_LDD_0, @@ -205,59 +239,24 @@ static inline void __init colibri_pxa320_init_ac97(void) static inline void colibri_pxa320_init_ac97(void) {} #endif -/* - * The following configuration is verified to work with the Toradex Orchid - * carrier board - */ -static mfp_cfg_t colibri_pxa320_uart_pin_config[] __initdata = { - /* UART 1 configuration (may be set by bootloader) */ - GPIO99_UART1_CTS, - GPIO104_UART1_RTS, - GPIO97_UART1_RXD, - GPIO98_UART1_TXD, - GPIO101_UART1_DTR, - GPIO103_UART1_DSR, - GPIO100_UART1_DCD, - GPIO102_UART1_RI, - - /* UART 2 configuration */ - GPIO109_UART2_CTS, - GPIO112_UART2_RTS, - GPIO110_UART2_RXD, - GPIO111_UART2_TXD, - - /* UART 3 configuration */ - GPIO30_UART3_RXD, - GPIO31_UART3_TXD, -}; - -static void __init colibri_pxa320_init_uart(void) -{ - pxa3xx_mfp_config(ARRAY_AND_SIZE(colibri_pxa320_uart_pin_config)); -} - void __init colibri_pxa320_init(void) { - pxa_set_ffuart_info(NULL); - pxa_set_btuart_info(NULL); - pxa_set_stuart_info(NULL); - colibri_pxa320_init_eth(); - colibri_pxa320_init_ohci(); colibri_pxa3xx_init_nand(); colibri_pxa320_init_lcd(); colibri_pxa3xx_init_lcd(mfp_to_gpio(GPIO49_GPIO)); colibri_pxa320_init_ac97(); - colibri_pxa3xx_init_mmc(ARRAY_AND_SIZE(colibri_pxa320_mmc_pin_config), - mfp_to_gpio(MFP_PIN_GPIO28)); - colibri_pxa320_init_uart(); colibri_pxa320_init_udc(); + + /* Evalboard init */ + pxa3xx_mfp_config(ARRAY_AND_SIZE(colibri_pxa320_evalboard_pin_config)); + colibri_evalboard_init(); } MACHINE_START(COLIBRI320, "Toradex Colibri PXA320") .boot_params = COLIBRI_SDRAM_BASE + 0x100, .init_machine = colibri_pxa320_init, - .map_io = pxa_map_io, + .map_io = pxa3xx_map_io, .init_irq = pxa3xx_init_irq, .timer = &pxa_timer, MACHINE_END diff --git a/arch/arm/mach-pxa/colibri-pxa3xx.c b/arch/arm/mach-pxa/colibri-pxa3xx.c index 199afa2..96b2d9f 100644 --- a/arch/arm/mach-pxa/colibri-pxa3xx.c +++ b/arch/arm/mach-pxa/colibri-pxa3xx.c @@ -64,55 +64,6 @@ void __init colibri_pxa3xx_init_eth(struct ax_plat_data *plat_data) } #endif -#if defined(CONFIG_MMC_PXA) || defined(CONFIG_MMC_PXA_MODULE) -static int mmc_detect_pin; - -static int colibri_pxa3xx_mci_init(struct device *dev, - irq_handler_t colibri_mmc_detect_int, - void *data) -{ - int ret; - - ret = gpio_request(mmc_detect_pin, "mmc card detect"); - if (ret) - return ret; - - gpio_direction_input(mmc_detect_pin); - ret = request_irq(gpio_to_irq(mmc_detect_pin), colibri_mmc_detect_int, - IRQF_TRIGGER_RISING | IRQF_TRIGGER_FALLING, - "MMC card detect", data); - if (ret) { - gpio_free(mmc_detect_pin); - return ret; - } - - return 0; -} - -static void colibri_pxa3xx_mci_exit(struct device *dev, void *data) -{ - free_irq(mmc_detect_pin, data); - gpio_free(gpio_to_irq(mmc_detect_pin)); -} - -static struct pxamci_platform_data colibri_pxa3xx_mci_platform_data = { - .detect_delay_ms = 200, - .ocr_mask = MMC_VDD_32_33 | MMC_VDD_33_34, - .init = colibri_pxa3xx_mci_init, - .exit = colibri_pxa3xx_mci_exit, - .gpio_card_detect = -1, - .gpio_card_ro = -1, - .gpio_power = -1, -}; - -void __init colibri_pxa3xx_init_mmc(mfp_cfg_t *pins, int len, int detect_pin) -{ - pxa3xx_mfp_config(pins, len); - mmc_detect_pin = detect_pin; - pxa_set_mci_info(&colibri_pxa3xx_mci_platform_data); -} -#endif /* CONFIG_MMC_PXA || CONFIG_MMC_PXA_MODULE */ - #if defined(CONFIG_FB_PXA) || defined(CONFIG_FB_PXA_MODULE) static int lcd_bl_pin; diff --git a/arch/arm/mach-pxa/corgi.c b/arch/arm/mach-pxa/corgi.c index 821229ac..a5452a3 100644 --- a/arch/arm/mach-pxa/corgi.c +++ b/arch/arm/mach-pxa/corgi.c @@ -28,6 +28,7 @@ #include <linux/spi/spi.h> #include <linux/spi/ads7846.h> #include <linux/spi/corgi_lcd.h> +#include <linux/spi/pxa2xx_spi.h> #include <linux/mtd/sharpsl.h> #include <linux/input/matrix_keypad.h> #include <video/w100fb.h> @@ -48,7 +49,6 @@ #include <mach/irda.h> #include <mach/mmc.h> #include <mach/udc.h> -#include <mach/pxa2xx_spi.h> #include <mach/corgi.h> #include <mach/sharpsl_pm.h> @@ -721,7 +721,7 @@ static void __init fixup_corgi(struct machine_desc *desc, #ifdef CONFIG_MACH_CORGI MACHINE_START(CORGI, "SHARP Corgi") .fixup = fixup_corgi, - .map_io = pxa_map_io, + .map_io = pxa25x_map_io, .init_irq = pxa25x_init_irq, .init_machine = corgi_init, .timer = &pxa_timer, @@ -731,7 +731,7 @@ MACHINE_END #ifdef CONFIG_MACH_SHEPHERD MACHINE_START(SHEPHERD, "SHARP Shepherd") .fixup = fixup_corgi, - .map_io = pxa_map_io, + .map_io = pxa25x_map_io, .init_irq = pxa25x_init_irq, .init_machine = corgi_init, .timer = &pxa_timer, @@ -741,7 +741,7 @@ MACHINE_END #ifdef CONFIG_MACH_HUSKY MACHINE_START(HUSKY, "SHARP Husky") .fixup = fixup_corgi, - .map_io = pxa_map_io, + .map_io = pxa25x_map_io, .init_irq = pxa25x_init_irq, .init_machine = corgi_init, .timer = &pxa_timer, diff --git a/arch/arm/mach-pxa/cpufreq-pxa2xx.c b/arch/arm/mach-pxa/cpufreq-pxa2xx.c index 58093d9..6a7aeab 100644 --- a/arch/arm/mach-pxa/cpufreq-pxa2xx.c +++ b/arch/arm/mach-pxa/cpufreq-pxa2xx.c @@ -38,8 +38,10 @@ #include <linux/cpufreq.h> #include <linux/err.h> #include <linux/regulator/consumer.h> +#include <linux/io.h> #include <mach/pxa2xx-regs.h> +#include <mach/smemc.h> #ifdef DEBUG static unsigned int freq_debug; @@ -242,7 +244,7 @@ static void pxa27x_guess_max_freq(void) static void init_sdram_rows(void) { - uint32_t mdcnfg = MDCNFG; + uint32_t mdcnfg = __raw_readl(MDCNFG); unsigned int drac2 = 0, drac0 = 0; if (mdcnfg & (MDCNFG_DE2 | MDCNFG_DE3)) @@ -331,8 +333,8 @@ static int pxa_set_target(struct cpufreq_policy *policy, * we need to preset the smaller DRI before the change. If we're * speeding up we need to set the larger DRI value after the change. */ - preset_mdrefr = postset_mdrefr = MDREFR; - if ((MDREFR & MDREFR_DRI_MASK) > mdrefr_dri(new_freq_mem)) { + preset_mdrefr = postset_mdrefr = __raw_readl(MDREFR); + if ((preset_mdrefr & MDREFR_DRI_MASK) > mdrefr_dri(new_freq_mem)) { preset_mdrefr = (preset_mdrefr & ~MDREFR_DRI_MASK); preset_mdrefr |= mdrefr_dri(new_freq_mem); } @@ -370,7 +372,7 @@ static int pxa_set_target(struct cpufreq_policy *policy, 3: nop \n\ " : "=&r" (unused) - : "r" (&MDREFR), "r" (cclkcfg), + : "r" (MDREFR), "r" (cclkcfg), "r" (preset_mdrefr), "r" (postset_mdrefr) : "r4", "r5"); local_irq_restore(flags); diff --git a/arch/arm/mach-pxa/csb726.c b/arch/arm/mach-pxa/csb726.c index 57cacaf..a305424 100644 --- a/arch/arm/mach-pxa/csb726.c +++ b/arch/arm/mach-pxa/csb726.c @@ -27,6 +27,7 @@ #include <mach/ohci.h> #include <mach/pxa2xx-regs.h> #include <mach/audio.h> +#include <mach/smemc.h> #include "generic.h" #include "devices.h" @@ -255,9 +256,9 @@ static struct platform_device *devices[] __initdata = { static void __init csb726_init(void) { pxa2xx_mfp_config(ARRAY_AND_SIZE(csb726_pin_config)); -/* MSC1 = 0x7ffc3ffc; *//* LAN9215/EXP_CS */ -/* MSC2 = 0x06697ff4; *//* none/SM501 */ - MSC2 = (MSC2 & ~0xffff) | 0x7ff4; /* SM501 */ +/* __raw_writel(0x7ffc3ffc, MSC1); *//* LAN9215/EXP_CS */ +/* __raw_writel(0x06697ff4, MSC2); *//* none/SM501 */ + __raw_writel((__raw_readl(MSC2) & ~0xffff) | 0x7ff4, MSC2); /* SM501 */ pxa_set_ffuart_info(NULL); pxa_set_btuart_info(NULL); @@ -273,7 +274,7 @@ static void __init csb726_init(void) MACHINE_START(CSB726, "Cogent CSB726") .boot_params = 0xa0000100, - .map_io = pxa_map_io, + .map_io = pxa27x_map_io, .init_irq = pxa27x_init_irq, .init_machine = csb726_init, .timer = &pxa_timer, diff --git a/arch/arm/mach-pxa/devices.c b/arch/arm/mach-pxa/devices.c index aaa1166..4c766e3 100644 --- a/arch/arm/mach-pxa/devices.c +++ b/arch/arm/mach-pxa/devices.c @@ -3,6 +3,7 @@ #include <linux/init.h> #include <linux/platform_device.h> #include <linux/dma-mapping.h> +#include <linux/spi/pxa2xx_spi.h> #include <asm/pmu.h> #include <mach/udc.h> @@ -12,7 +13,6 @@ #include <mach/irda.h> #include <mach/ohci.h> #include <plat/pxa27x_keypad.h> -#include <mach/pxa2xx_spi.h> #include <mach/camera.h> #include <mach/audio.h> #include <mach/hardware.h> @@ -342,27 +342,6 @@ struct platform_device pxa27x_device_i2c_power = { }; #endif -#ifdef CONFIG_PXA3xx -static struct resource pxa3xx_resources_i2c_power[] = { - { - .start = 0x40f500c0, - .end = 0x40f500d3, - .flags = IORESOURCE_MEM, - }, { - .start = IRQ_PWRI2C, - .end = IRQ_PWRI2C, - .flags = IORESOURCE_IRQ, - }, -}; - -struct platform_device pxa3xx_device_i2c_power = { - .name = "pxa3xx-pwri2c", - .id = 1, - .resource = pxa3xx_resources_i2c_power, - .num_resources = ARRAY_SIZE(pxa3xx_resources_i2c_power), -}; -#endif - static struct resource pxai2s_resources[] = { { .start = 0x40400000, @@ -633,30 +612,35 @@ struct platform_device pxa25x_device_assp = { #endif /* CONFIG_PXA25x */ #if defined(CONFIG_PXA27x) || defined(CONFIG_PXA3xx) - -static struct resource pxa27x_resource_keypad[] = { +static struct resource pxa27x_resource_camera[] = { [0] = { - .start = 0x41500000, - .end = 0x4150004c, + .start = 0x50000000, + .end = 0x50000fff, .flags = IORESOURCE_MEM, }, [1] = { - .start = IRQ_KEYPAD, - .end = IRQ_KEYPAD, + .start = IRQ_CAMERA, + .end = IRQ_CAMERA, .flags = IORESOURCE_IRQ, }, }; -struct platform_device pxa27x_device_keypad = { - .name = "pxa27x-keypad", - .id = -1, - .resource = pxa27x_resource_keypad, - .num_resources = ARRAY_SIZE(pxa27x_resource_keypad), +static u64 pxa27x_dma_mask_camera = DMA_BIT_MASK(32); + +static struct platform_device pxa27x_device_camera = { + .name = "pxa27x-camera", + .id = 0, /* This is used to put cameras on this interface */ + .dev = { + .dma_mask = &pxa27x_dma_mask_camera, + .coherent_dma_mask = 0xffffffff, + }, + .num_resources = ARRAY_SIZE(pxa27x_resource_camera), + .resource = pxa27x_resource_camera, }; -void __init pxa_set_keypad_info(struct pxa27x_keypad_platform_data *info) +void __init pxa_set_camera_info(struct pxacamera_platform_data *info) { - pxa_register_device(&pxa27x_device_keypad, info); + pxa_register_device(&pxa27x_device_camera, info); } static u64 pxa27x_ohci_dma_mask = DMA_BIT_MASK(32); @@ -689,6 +673,33 @@ void __init pxa_set_ohci_info(struct pxaohci_platform_data *info) { pxa_register_device(&pxa27x_device_ohci, info); } +#endif /* CONFIG_PXA27x || CONFIG_PXA3xx */ + +#if defined(CONFIG_PXA27x) || defined(CONFIG_PXA3xx) || defined(CONFIG_PXA95x) +static struct resource pxa27x_resource_keypad[] = { + [0] = { + .start = 0x41500000, + .end = 0x4150004c, + .flags = IORESOURCE_MEM, + }, + [1] = { + .start = IRQ_KEYPAD, + .end = IRQ_KEYPAD, + .flags = IORESOURCE_IRQ, + }, +}; + +struct platform_device pxa27x_device_keypad = { + .name = "pxa27x-keypad", + .id = -1, + .resource = pxa27x_resource_keypad, + .num_resources = ARRAY_SIZE(pxa27x_resource_keypad), +}; + +void __init pxa_set_keypad_info(struct pxa27x_keypad_platform_data *info) +{ + pxa_register_device(&pxa27x_device_keypad, info); +} static u64 pxa27x_ssp1_dma_mask = DMA_BIT_MASK(32); @@ -833,79 +844,9 @@ struct platform_device pxa27x_device_pwm1 = { .resource = pxa27x_resource_pwm1, .num_resources = ARRAY_SIZE(pxa27x_resource_pwm1), }; - -static struct resource pxa27x_resource_camera[] = { - [0] = { - .start = 0x50000000, - .end = 0x50000fff, - .flags = IORESOURCE_MEM, - }, - [1] = { - .start = IRQ_CAMERA, - .end = IRQ_CAMERA, - .flags = IORESOURCE_IRQ, - }, -}; - -static u64 pxa27x_dma_mask_camera = DMA_BIT_MASK(32); - -static struct platform_device pxa27x_device_camera = { - .name = "pxa27x-camera", - .id = 0, /* This is used to put cameras on this interface */ - .dev = { - .dma_mask = &pxa27x_dma_mask_camera, - .coherent_dma_mask = 0xffffffff, - }, - .num_resources = ARRAY_SIZE(pxa27x_resource_camera), - .resource = pxa27x_resource_camera, -}; - -void __init pxa_set_camera_info(struct pxacamera_platform_data *info) -{ - pxa_register_device(&pxa27x_device_camera, info); -} -#endif /* CONFIG_PXA27x || CONFIG_PXA3xx */ +#endif /* CONFIG_PXA27x || CONFIG_PXA3xx || CONFIG_PXA95x*/ #ifdef CONFIG_PXA3xx -static u64 pxa3xx_ssp4_dma_mask = DMA_BIT_MASK(32); - -static struct resource pxa3xx_resource_ssp4[] = { - [0] = { - .start = 0x41a00000, - .end = 0x41a0003f, - .flags = IORESOURCE_MEM, - }, - [1] = { - .start = IRQ_SSP4, - .end = IRQ_SSP4, - .flags = IORESOURCE_IRQ, - }, - [2] = { - /* DRCMR for RX */ - .start = 2, - .end = 2, - .flags = IORESOURCE_DMA, - }, - [3] = { - /* DRCMR for TX */ - .start = 3, - .end = 3, - .flags = IORESOURCE_DMA, - }, -}; - -struct platform_device pxa3xx_device_ssp4 = { - /* PXA3xx SSP is basically equivalent to PXA27x */ - .name = "pxa27x-ssp", - .id = 3, - .dev = { - .dma_mask = &pxa3xx_ssp4_dma_mask, - .coherent_dma_mask = DMA_BIT_MASK(32), - }, - .resource = pxa3xx_resource_ssp4, - .num_resources = ARRAY_SIZE(pxa3xx_resource_ssp4), -}; - static struct resource pxa3xx_resources_mci2[] = { [0] = { .start = 0x42000000, @@ -984,6 +925,54 @@ void __init pxa3xx_set_mci3_info(struct pxamci_platform_data *info) pxa_register_device(&pxa3xx_device_mci3, info); } +static struct resource pxa3xx_resources_gcu[] = { + { + .start = 0x54000000, + .end = 0x54000fff, + .flags = IORESOURCE_MEM, + }, + { + .start = IRQ_GCU, + .end = IRQ_GCU, + .flags = IORESOURCE_IRQ, + }, +}; + +static u64 pxa3xx_gcu_dmamask = DMA_BIT_MASK(32); + +struct platform_device pxa3xx_device_gcu = { + .name = "pxa3xx-gcu", + .id = -1, + .num_resources = ARRAY_SIZE(pxa3xx_resources_gcu), + .resource = pxa3xx_resources_gcu, + .dev = { + .dma_mask = &pxa3xx_gcu_dmamask, + .coherent_dma_mask = 0xffffffff, + }, +}; + +#endif /* CONFIG_PXA3xx */ + +#if defined(CONFIG_PXA3xx) || defined(CONFIG_PXA95x) +static struct resource pxa3xx_resources_i2c_power[] = { + { + .start = 0x40f500c0, + .end = 0x40f500d3, + .flags = IORESOURCE_MEM, + }, { + .start = IRQ_PWRI2C, + .end = IRQ_PWRI2C, + .flags = IORESOURCE_IRQ, + }, +}; + +struct platform_device pxa3xx_device_i2c_power = { + .name = "pxa3xx-pwri2c", + .id = 1, + .resource = pxa3xx_resources_i2c_power, + .num_resources = ARRAY_SIZE(pxa3xx_resources_i2c_power), +}; + static struct resource pxa3xx_resources_nand[] = { [0] = { .start = 0x43100000, @@ -1027,33 +1016,45 @@ void __init pxa3xx_set_nand_info(struct pxa3xx_nand_platform_data *info) pxa_register_device(&pxa3xx_device_nand, info); } -static struct resource pxa3xx_resources_gcu[] = { - { - .start = 0x54000000, - .end = 0x54000fff, +static u64 pxa3xx_ssp4_dma_mask = DMA_BIT_MASK(32); + +static struct resource pxa3xx_resource_ssp4[] = { + [0] = { + .start = 0x41a00000, + .end = 0x41a0003f, .flags = IORESOURCE_MEM, }, - { - .start = IRQ_GCU, - .end = IRQ_GCU, + [1] = { + .start = IRQ_SSP4, + .end = IRQ_SSP4, .flags = IORESOURCE_IRQ, }, + [2] = { + /* DRCMR for RX */ + .start = 2, + .end = 2, + .flags = IORESOURCE_DMA, + }, + [3] = { + /* DRCMR for TX */ + .start = 3, + .end = 3, + .flags = IORESOURCE_DMA, + }, }; -static u64 pxa3xx_gcu_dmamask = DMA_BIT_MASK(32); - -struct platform_device pxa3xx_device_gcu = { - .name = "pxa3xx-gcu", - .id = -1, - .num_resources = ARRAY_SIZE(pxa3xx_resources_gcu), - .resource = pxa3xx_resources_gcu, +struct platform_device pxa3xx_device_ssp4 = { + /* PXA3xx SSP is basically equivalent to PXA27x */ + .name = "pxa27x-ssp", + .id = 3, .dev = { - .dma_mask = &pxa3xx_gcu_dmamask, - .coherent_dma_mask = 0xffffffff, + .dma_mask = &pxa3xx_ssp4_dma_mask, + .coherent_dma_mask = DMA_BIT_MASK(32), }, + .resource = pxa3xx_resource_ssp4, + .num_resources = ARRAY_SIZE(pxa3xx_resource_ssp4), }; - -#endif /* CONFIG_PXA3xx */ +#endif /* CONFIG_PXA3xx || CONFIG_PXA95x */ /* pxa2xx-spi platform-device ID equals respective SSP platform-device ID + 1. * See comment in arch/arm/mach-pxa/ssp.c::ssp_probe() */ diff --git a/arch/arm/mach-pxa/em-x270.c b/arch/arm/mach-pxa/em-x270.c index ed0dbfdb..a78bb30 100644 --- a/arch/arm/mach-pxa/em-x270.c +++ b/arch/arm/mach-pxa/em-x270.c @@ -26,6 +26,7 @@ #include <linux/spi/spi.h> #include <linux/spi/tdo24m.h> #include <linux/spi/libertas_spi.h> +#include <linux/spi/pxa2xx_spi.h> #include <linux/power_supply.h> #include <linux/apm-emulation.h> #include <linux/i2c.h> @@ -46,7 +47,6 @@ #include <plat/pxa27x_keypad.h> #include <plat/i2c.h> #include <mach/camera.h> -#include <mach/pxa2xx_spi.h> #include "generic.h" #include "devices.h" @@ -1300,7 +1300,7 @@ static void __init em_x270_init(void) MACHINE_START(EM_X270, "Compulab EM-X270") .boot_params = 0xa0000100, - .map_io = pxa_map_io, + .map_io = pxa27x_map_io, .init_irq = pxa27x_init_irq, .timer = &pxa_timer, .init_machine = em_x270_init, @@ -1308,7 +1308,7 @@ MACHINE_END MACHINE_START(EXEDA, "Compulab eXeda") .boot_params = 0xa0000100, - .map_io = pxa_map_io, + .map_io = pxa27x_map_io, .init_irq = pxa27x_init_irq, .timer = &pxa_timer, .init_machine = em_x270_init, diff --git a/arch/arm/mach-pxa/eseries.c b/arch/arm/mach-pxa/eseries.c index b25690c..edca0a0 100644 --- a/arch/arm/mach-pxa/eseries.c +++ b/arch/arm/mach-pxa/eseries.c @@ -181,7 +181,7 @@ static void __init e330_init(void) MACHINE_START(E330, "Toshiba e330") /* Maintainer: Ian Molton (spyro@f2s.com) */ .boot_params = 0xa0000100, - .map_io = pxa_map_io, + .map_io = pxa25x_map_io, .nr_irqs = ESERIES_NR_IRQS, .init_irq = pxa25x_init_irq, .fixup = eseries_fixup, @@ -230,7 +230,7 @@ static void __init e350_init(void) MACHINE_START(E350, "Toshiba e350") /* Maintainer: Ian Molton (spyro@f2s.com) */ .boot_params = 0xa0000100, - .map_io = pxa_map_io, + .map_io = pxa25x_map_io, .nr_irqs = ESERIES_NR_IRQS, .init_irq = pxa25x_init_irq, .fixup = eseries_fixup, @@ -352,7 +352,7 @@ static void __init e400_init(void) MACHINE_START(E400, "Toshiba e400") /* Maintainer: Ian Molton (spyro@f2s.com) */ .boot_params = 0xa0000100, - .map_io = pxa_map_io, + .map_io = pxa25x_map_io, .nr_irqs = ESERIES_NR_IRQS, .init_irq = pxa25x_init_irq, .fixup = eseries_fixup, @@ -540,7 +540,7 @@ static void __init e740_init(void) MACHINE_START(E740, "Toshiba e740") /* Maintainer: Ian Molton (spyro@f2s.com) */ .boot_params = 0xa0000100, - .map_io = pxa_map_io, + .map_io = pxa25x_map_io, .nr_irqs = ESERIES_NR_IRQS, .init_irq = pxa25x_init_irq, .fixup = eseries_fixup, @@ -731,7 +731,7 @@ static void __init e750_init(void) MACHINE_START(E750, "Toshiba e750") /* Maintainer: Ian Molton (spyro@f2s.com) */ .boot_params = 0xa0000100, - .map_io = pxa_map_io, + .map_io = pxa25x_map_io, .nr_irqs = ESERIES_NR_IRQS, .init_irq = pxa25x_init_irq, .fixup = eseries_fixup, @@ -926,7 +926,7 @@ static void __init e800_init(void) MACHINE_START(E800, "Toshiba e800") /* Maintainer: Ian Molton (spyro@f2s.com) */ .boot_params = 0xa0000100, - .map_io = pxa_map_io, + .map_io = pxa25x_map_io, .nr_irqs = ESERIES_NR_IRQS, .init_irq = pxa25x_init_irq, .fixup = eseries_fixup, diff --git a/arch/arm/mach-pxa/ezx.c b/arch/arm/mach-pxa/ezx.c index 142c711..87cec0a 100644 --- a/arch/arm/mach-pxa/ezx.c +++ b/arch/arm/mach-pxa/ezx.c @@ -798,7 +798,7 @@ static void __init a780_init(void) MACHINE_START(EZX_A780, "Motorola EZX A780") .boot_params = 0xa0000100, - .map_io = pxa_map_io, + .map_io = pxa27x_map_io, .nr_irqs = EZX_NR_IRQS, .init_irq = pxa27x_init_irq, .timer = &pxa_timer, @@ -863,7 +863,7 @@ static void __init e680_init(void) MACHINE_START(EZX_E680, "Motorola EZX E680") .boot_params = 0xa0000100, - .map_io = pxa_map_io, + .map_io = pxa27x_map_io, .nr_irqs = EZX_NR_IRQS, .init_irq = pxa27x_init_irq, .timer = &pxa_timer, @@ -928,7 +928,7 @@ static void __init a1200_init(void) MACHINE_START(EZX_A1200, "Motorola EZX A1200") .boot_params = 0xa0000100, - .map_io = pxa_map_io, + .map_io = pxa27x_map_io, .nr_irqs = EZX_NR_IRQS, .init_irq = pxa27x_init_irq, .timer = &pxa_timer, @@ -1118,7 +1118,7 @@ static void __init a910_init(void) MACHINE_START(EZX_A910, "Motorola EZX A910") .boot_params = 0xa0000100, - .map_io = pxa_map_io, + .map_io = pxa27x_map_io, .nr_irqs = EZX_NR_IRQS, .init_irq = pxa27x_init_irq, .timer = &pxa_timer, @@ -1183,7 +1183,7 @@ static void __init e6_init(void) MACHINE_START(EZX_E6, "Motorola EZX E6") .boot_params = 0xa0000100, - .map_io = pxa_map_io, + .map_io = pxa27x_map_io, .nr_irqs = EZX_NR_IRQS, .init_irq = pxa27x_init_irq, .timer = &pxa_timer, @@ -1222,7 +1222,7 @@ static void __init e2_init(void) MACHINE_START(EZX_E2, "Motorola EZX E2") .boot_params = 0xa0000100, - .map_io = pxa_map_io, + .map_io = pxa27x_map_io, .nr_irqs = EZX_NR_IRQS, .init_irq = pxa27x_init_irq, .timer = &pxa_timer, diff --git a/arch/arm/mach-pxa/generic.c b/arch/arm/mach-pxa/generic.c index 6451e9c..d6e15f7 100644 --- a/arch/arm/mach-pxa/generic.c +++ b/arch/arm/mach-pxa/generic.c @@ -28,6 +28,8 @@ #include <mach/reset.h> #include <mach/gpio.h> +#include <mach/smemc.h> +#include <mach/pxa3xx-regs.h> #include "generic.h" @@ -35,9 +37,10 @@ void clear_reset_status(unsigned int mask) { if (cpu_is_pxa2xx()) pxa2xx_clear_reset_status(mask); - - if (cpu_is_pxa3xx()) - pxa3xx_clear_reset_status(mask); + else { + /* RESET_STATUS_* has a 1:1 mapping with ARSR */ + ARSR = mask; + } } unsigned long get_clock_tick_rate(void) @@ -71,47 +74,17 @@ unsigned int get_clk_frequency_khz(int info) EXPORT_SYMBOL(get_clk_frequency_khz); /* - * Return the current memory clock frequency in units of 10kHz - */ -unsigned int get_memclk_frequency_10khz(void) -{ - if (cpu_is_pxa25x()) - return pxa25x_get_memclk_frequency_10khz(); - else if (cpu_is_pxa27x()) - return pxa27x_get_memclk_frequency_10khz(); - return 0; -} -EXPORT_SYMBOL(get_memclk_frequency_10khz); - -/* * Intel PXA2xx internal register mapping. * - * Note 1: not all PXA2xx variants implement all those addresses. - * - * Note 2: virtual 0xfffe0000-0xffffffff is reserved for the vector table - * and cache flush area. + * Note: virtual 0xfffe0000-0xffffffff is reserved for the vector table + * and cache flush area. */ -static struct map_desc standard_io_desc[] __initdata = { +static struct map_desc common_io_desc[] __initdata = { { /* Devs */ .virtual = 0xf2000000, .pfn = __phys_to_pfn(0x40000000), .length = 0x02000000, .type = MT_DEVICE - }, { /* Mem Ctl */ - .virtual = 0xf6000000, - .pfn = __phys_to_pfn(0x48000000), - .length = 0x00200000, - .type = MT_DEVICE - }, { /* Camera */ - .virtual = 0xfa000000, - .pfn = __phys_to_pfn(0x50000000), - .length = 0x00100000, - .type = MT_DEVICE - }, { /* IMem ctl */ - .virtual = 0xfe000000, - .pfn = __phys_to_pfn(0x58000000), - .length = 0x00100000, - .type = MT_DEVICE }, { /* UNCACHED_PHYS_0 */ .virtual = 0xff000000, .pfn = __phys_to_pfn(0x00000000), @@ -122,6 +95,5 @@ static struct map_desc standard_io_desc[] __initdata = { void __init pxa_map_io(void) { - iotable_init(standard_io_desc, ARRAY_SIZE(standard_io_desc)); - get_clk_frequency_khz(1); + iotable_init(ARRAY_AND_SIZE(common_io_desc)); } diff --git a/arch/arm/mach-pxa/generic.h b/arch/arm/mach-pxa/generic.h index 4b1ad27..6205dc9 100644 --- a/arch/arm/mach-pxa/generic.h +++ b/arch/arm/mach-pxa/generic.h @@ -20,7 +20,12 @@ extern void __init pxa26x_init_irq(void); #endif extern void __init pxa27x_init_irq(void); extern void __init pxa3xx_init_irq(void); +extern void __init pxa95x_init_irq(void); + extern void __init pxa_map_io(void); +extern void __init pxa25x_map_io(void); +extern void __init pxa27x_map_io(void); +extern void __init pxa3xx_map_io(void); extern unsigned int get_clk_frequency_khz(int info); @@ -32,18 +37,14 @@ extern unsigned int get_clk_frequency_khz(int info); #ifdef CONFIG_PXA25x extern unsigned pxa25x_get_clk_frequency_khz(int); -extern unsigned pxa25x_get_memclk_frequency_10khz(void); #else #define pxa25x_get_clk_frequency_khz(x) (0) -#define pxa25x_get_memclk_frequency_10khz() (0) #endif #ifdef CONFIG_PXA27x extern unsigned pxa27x_get_clk_frequency_khz(int); -extern unsigned pxa27x_get_memclk_frequency_10khz(void); #else #define pxa27x_get_clk_frequency_khz(x) (0) -#define pxa27x_get_memclk_frequency_10khz() (0) #endif #if defined(CONFIG_PXA25x) || defined(CONFIG_PXA27x) @@ -54,10 +55,8 @@ static inline void pxa2xx_clear_reset_status(unsigned int mask) {} #ifdef CONFIG_PXA3xx extern unsigned pxa3xx_get_clk_frequency_khz(int); -extern void pxa3xx_clear_reset_status(unsigned int); #else #define pxa3xx_get_clk_frequency_khz(x) (0) -static inline void pxa3xx_clear_reset_status(unsigned int mask) {} #endif extern struct sysdev_class pxa_irq_sysclass; diff --git a/arch/arm/mach-pxa/gumstix.c b/arch/arm/mach-pxa/gumstix.c index 1e2a9a1..6fd319e 100644 --- a/arch/arm/mach-pxa/gumstix.c +++ b/arch/arm/mach-pxa/gumstix.c @@ -225,7 +225,7 @@ static void __init gumstix_init(void) MACHINE_START(GUMSTIX, "Gumstix") .boot_params = 0xa0000100, /* match u-boot bi_boot_params */ - .map_io = pxa_map_io, + .map_io = pxa25x_map_io, .init_irq = pxa25x_init_irq, .timer = &pxa_timer, .init_machine = gumstix_init, diff --git a/arch/arm/mach-pxa/h5000.c b/arch/arm/mach-pxa/h5000.c index 7057a1f..657db46 100644 --- a/arch/arm/mach-pxa/h5000.c +++ b/arch/arm/mach-pxa/h5000.c @@ -32,6 +32,7 @@ #include <mach/pxa25x.h> #include <mach/h5000.h> #include <mach/udc.h> +#include <mach/smemc.h> #include "generic.h" @@ -172,11 +173,11 @@ static unsigned long h5000_pin_config[] __initdata = { static void fix_msc(void) { - MSC0 = 0x129c24f2; - MSC1 = 0x7ff424fa; - MSC2 = 0x7ff47ff4; + __raw_writel(0x129c24f2, MSC0); + __raw_writel(0x7ff424fa, MSC1); + __raw_writel(0x7ff47ff4, MSC2); - MDREFR |= 0x02080000; + __raw_writel(__raw_readl(MDREFR) | 0x02080000, MDREFR); } /* @@ -202,7 +203,7 @@ static void __init h5000_init(void) MACHINE_START(H5400, "HP iPAQ H5000") .boot_params = 0xa0000100, - .map_io = pxa_map_io, + .map_io = pxa25x_map_io, .init_irq = pxa25x_init_irq, .timer = &pxa_timer, .init_machine = h5000_init, diff --git a/arch/arm/mach-pxa/himalaya.c b/arch/arm/mach-pxa/himalaya.c index 01b7f07..e8603eb 100644 --- a/arch/arm/mach-pxa/himalaya.c +++ b/arch/arm/mach-pxa/himalaya.c @@ -160,7 +160,7 @@ static void __init himalaya_init(void) MACHINE_START(HIMALAYA, "HTC Himalaya") .boot_params = 0xa0000100, - .map_io = pxa_map_io, + .map_io = pxa25x_map_io, .init_irq = pxa25x_init_irq, .init_machine = himalaya_init, .timer = &pxa_timer, diff --git a/arch/arm/mach-pxa/hx4700.c b/arch/arm/mach-pxa/hx4700.c index 76d93a2..a908e0a 100644 --- a/arch/arm/mach-pxa/hx4700.c +++ b/arch/arm/mach-pxa/hx4700.c @@ -33,6 +33,7 @@ #include <linux/regulator/max1586.h> #include <linux/spi/ads7846.h> #include <linux/spi/spi.h> +#include <linux/spi/pxa2xx_spi.h> #include <linux/usb/gpio_vbus.h> #include <mach/hardware.h> @@ -43,7 +44,6 @@ #include <mach/hx4700.h> #include <plat/i2c.h> #include <mach/irda.h> -#include <mach/pxa2xx_spi.h> #include <video/platform_lcd.h> #include <video/w100fb.h> @@ -871,7 +871,7 @@ static void __init hx4700_init(void) MACHINE_START(H4700, "HP iPAQ HX4700") .boot_params = 0xa0000100, - .map_io = pxa_map_io, + .map_io = pxa27x_map_io, .nr_irqs = HX4700_NR_IRQS, .init_irq = pxa27x_init_irq, .init_machine = hx4700_init, diff --git a/arch/arm/mach-pxa/icontrol.c b/arch/arm/mach-pxa/icontrol.c index d51ee3d..6cedc81 100644 --- a/arch/arm/mach-pxa/icontrol.c +++ b/arch/arm/mach-pxa/icontrol.c @@ -24,7 +24,7 @@ #include <mach/mxm8x10.h> #include <linux/spi/spi.h> -#include <mach/pxa2xx_spi.h> +#include <linux/spi/pxa2xx_spi.h> #include <linux/can/platform/mcp251x.h> #include "generic.h" @@ -192,7 +192,7 @@ static void __init icontrol_init(void) MACHINE_START(ICONTROL, "iControl/SafeTcam boards using Embedian MXM-8x10 CoM") .boot_params = 0xa0000100, - .map_io = pxa_map_io, + .map_io = pxa3xx_map_io, .init_irq = pxa3xx_init_irq, .timer = &pxa_timer, .init_machine = icontrol_init diff --git a/arch/arm/mach-pxa/idp.c b/arch/arm/mach-pxa/idp.c index e773dce..dd40e4a 100644 --- a/arch/arm/mach-pxa/idp.c +++ b/arch/arm/mach-pxa/idp.c @@ -187,7 +187,7 @@ static struct map_desc idp_io_desc[] __initdata = { static void __init idp_map_io(void) { - pxa_map_io(); + pxa25x_map_io(); iotable_init(idp_io_desc, ARRAY_SIZE(idp_io_desc)); } diff --git a/arch/arm/mach-pxa/include/mach/addr-map.h b/arch/arm/mach-pxa/include/mach/addr-map.h new file mode 100644 index 0000000..f4c0365 --- /dev/null +++ b/arch/arm/mach-pxa/include/mach/addr-map.h @@ -0,0 +1,48 @@ +#ifndef __ASM_MACH_ADDR_MAP_H +#define __ASM_MACH_ADDR_MAP_H + +/* + * Chip Selects + */ +#define PXA_CS0_PHYS 0x00000000 +#define PXA_CS1_PHYS 0x04000000 +#define PXA_CS2_PHYS 0x08000000 +#define PXA_CS3_PHYS 0x0C000000 +#define PXA_CS4_PHYS 0x10000000 +#define PXA_CS5_PHYS 0x14000000 + +#define PXA300_CS0_PHYS 0x00000000 /* PXA300/PXA310 _only_ */ +#define PXA300_CS1_PHYS 0x30000000 /* PXA300/PXA310 _only_ */ +#define PXA3xx_CS2_PHYS 0x10000000 +#define PXA3xx_CS3_PHYS 0x14000000 + +/* + * Peripheral Bus + */ +#define PERIPH_PHYS 0x40000000 +#define PERIPH_VIRT 0xf2000000 +#define PERIPH_SIZE 0x02000000 + +/* + * Static Memory Controller (w/ SDRAM controls on PXA25x/PXA27x) + */ +#define PXA2XX_SMEMC_PHYS 0x48000000 +#define PXA3XX_SMEMC_PHYS 0x4a000000 +#define SMEMC_VIRT 0xf6000000 +#define SMEMC_SIZE 0x00100000 + +/* + * Dynamic Memory Controller (only on PXA3xx) + */ +#define DMEMC_PHYS 0x48100000 +#define DMEMC_VIRT 0xf6100000 +#define DMEMC_SIZE 0x00100000 + +/* + * Internal Memory Controller (PXA27x and later) + */ +#define IMEMC_PHYS 0x58000000 +#define IMEMC_VIRT 0xfe000000 +#define IMEMC_SIZE 0x00100000 + +#endif /* __ASM_MACH_ADDR_MAP_H */ diff --git a/arch/arm/mach-pxa/include/mach/balloon3.h b/arch/arm/mach-pxa/include/mach/balloon3.h index 561562b..7074e76 100644 --- a/arch/arm/mach-pxa/include/mach/balloon3.h +++ b/arch/arm/mach-pxa/include/mach/balloon3.h @@ -26,6 +26,8 @@ enum balloon3_features { #define BALLOON3_FPGA_VIRT (0xf1000000) /* as per balloon2 */ #define BALLOON3_FPGA_LENGTH 0x01000000 +#define BALLOON3_FPGA_SETnCLR (0x1000) + /* FPGA / CPLD registers for CF socket */ #define BALLOON3_CF_STATUS_REG (BALLOON3_FPGA_VIRT + 0x00e00008) #define BALLOON3_CF_CONTROL_REG (BALLOON3_FPGA_VIRT + 0x00e00008) @@ -35,7 +37,7 @@ enum balloon3_features { #define BALLOON3_NAND_BASE (PXA_CS4_PHYS + 0x00e00000) #define BALLOON3_NAND_IO_REG (BALLOON3_FPGA_VIRT + 0x00e00000) #define BALLOON3_NAND_CONTROL2_REG (BALLOON3_FPGA_VIRT + 0x00e00010) -#define BALLOON3_NAND_STAT_REG (BALLOON3_FPGA_VIRT + 0x00e00010) +#define BALLOON3_NAND_STAT_REG (BALLOON3_FPGA_VIRT + 0x00e00014) #define BALLOON3_NAND_CONTROL_REG (BALLOON3_FPGA_VIRT + 0x00e00014) /* fpga/cpld interrupt control register */ @@ -174,7 +176,7 @@ enum balloon3_features { #define BALLOON3_CODEC_IRQ IRQ_GPIO(BALLOON3_GPIO_CODEC_IRQ) #define BALLOON3_S0_CD_IRQ IRQ_GPIO(BALLOON3_GPIO_S0_CD) -#define BALLOON3_NR_IRQS (IRQ_BOARD_START + 4) +#define BALLOON3_NR_IRQS (IRQ_BOARD_START + 16) extern int balloon3_has(enum balloon3_features feature); diff --git a/arch/arm/mach-pxa/include/mach/colibri.h b/arch/arm/mach-pxa/include/mach/colibri.h index 58dada1..388a96f 100644 --- a/arch/arm/mach-pxa/include/mach/colibri.h +++ b/arch/arm/mach-pxa/include/mach/colibri.h @@ -9,14 +9,14 @@ */ enum { - COLIBRI_PXA270_EVALBOARD = 0, + COLIBRI_EVALBOARD = 0, COLIBRI_PXA270_INCOME, }; -#if defined(CONFIG_MACH_COLIBRI_PXA270_EVALBOARD) -extern void colibri_pxa270_evalboard_init(void); +#if defined(CONFIG_MACH_COLIBRI_EVALBOARD) +extern void colibri_evalboard_init(void); #else -static inline void colibri_pxa270_evalboard_init(void) {} +static inline void colibri_evalboard_init(void) {} #endif #if defined(CONFIG_MACH_COLIBRI_PXA270_INCOME) @@ -59,5 +59,11 @@ static inline void colibri_pxa3xx_init_nand(void) {} #define GPIO0_COLIBRI_PXA270_SD_DETECT 0 #define GPIO113_COLIBRI_PXA270_TS_IRQ 113 +/* GPIO definitions for Colibri PXA300/310 */ +#define GPIO39_COLIBRI_PXA300_SD_DETECT 39 + +/* GPIO definitions for Colibri PXA320 */ +#define GPIO28_COLIBRI_PXA320_SD_DETECT 28 + #endif /* _COLIBRI_H_ */ diff --git a/arch/arm/mach-pxa/include/mach/hardware.h b/arch/arm/mach-pxa/include/mach/hardware.h index 814f145..6957ba5 100644 --- a/arch/arm/mach-pxa/include/mach/hardware.h +++ b/arch/arm/mach-pxa/include/mach/hardware.h @@ -13,6 +13,8 @@ #ifndef __ASM_ARCH_HARDWARE_H #define __ASM_ARCH_HARDWARE_H +#include <mach/addr-map.h> + /* * Workarounds for at least 2 errata so far require this. * The mapping is set in mach-pxa/generic.c. @@ -193,14 +195,15 @@ #define __cpu_is_pxa935(id) (0) #endif -#ifdef CONFIG_CPU_PXA950 -#define __cpu_is_pxa950(id) \ - ({ \ +#ifdef CONFIG_CPU_PXA955 +#define __cpu_is_pxa955(id) \ + ({ \ unsigned int _id = (id) >> 4 & 0xfff; \ - _id == 0x697; \ - }) + _id == 0x581 || _id == 0xc08 \ + || _id == 0xb76; \ + }) #else -#define __cpu_is_pxa950(id) (0) +#define __cpu_is_pxa955(id) (0) #endif #define cpu_is_pxa210() \ @@ -253,16 +256,15 @@ __cpu_is_pxa935(read_cpuid_id()); \ }) -#define cpu_is_pxa950() \ +#define cpu_is_pxa955() \ ({ \ - __cpu_is_pxa950(read_cpuid_id()); \ - }) + __cpu_is_pxa955(read_cpuid_id()); \ + }) /* * CPUID Core Generation Bit * <= 0x2 for pxa21x/pxa25x/pxa26x/pxa27x - * == 0x3 for pxa300/pxa310/pxa320 */ #if defined(CONFIG_PXA25x) || defined(CONFIG_PXA27x) #define __cpu_is_pxa2xx(id) \ @@ -277,8 +279,10 @@ #ifdef CONFIG_PXA3xx #define __cpu_is_pxa3xx(id) \ ({ \ - unsigned int _id = (id) >> 13 & 0x7; \ - _id == 0x3; \ + __cpu_is_pxa300(id) \ + || __cpu_is_pxa310(id) \ + || __cpu_is_pxa320(id) \ + || __cpu_is_pxa93x(id); \ }) #else #define __cpu_is_pxa3xx(id) (0) @@ -287,13 +291,22 @@ #if defined(CONFIG_CPU_PXA930) || defined(CONFIG_CPU_PXA935) #define __cpu_is_pxa93x(id) \ ({ \ - unsigned int _id = (id) >> 4 & 0xfff; \ - _id == 0x683 || _id == 0x693; \ + __cpu_is_pxa930(id) \ + || __cpu_is_pxa935(id); \ }) #else #define __cpu_is_pxa93x(id) (0) #endif +#ifdef CONFIG_PXA95x +#define __cpu_is_pxa95x(id) \ + ({ \ + __cpu_is_pxa955(id); \ + }) +#else +#define __cpu_is_pxa95x(id) (0) +#endif + #define cpu_is_pxa2xx() \ ({ \ __cpu_is_pxa2xx(read_cpuid_id()); \ @@ -308,6 +321,12 @@ ({ \ __cpu_is_pxa93x(read_cpuid_id()); \ }) + +#define cpu_is_pxa95x() \ + ({ \ + __cpu_is_pxa95x(read_cpuid_id()); \ + }) + /* * return current memory and LCD clock frequency in units of 10kHz */ diff --git a/arch/arm/mach-pxa/include/mach/irqs.h b/arch/arm/mach-pxa/include/mach/irqs.h index d372caa..a4285fc 100644 --- a/arch/arm/mach-pxa/include/mach/irqs.h +++ b/arch/arm/mach-pxa/include/mach/irqs.h @@ -21,16 +21,14 @@ #define PXA_IRQ(x) (PXA_ISA_IRQ_NUM + (x)) -#if defined(CONFIG_PXA27x) || defined(CONFIG_PXA3xx) #define IRQ_SSP3 PXA_IRQ(0) /* SSP3 service request */ #define IRQ_MSL PXA_IRQ(1) /* MSL Interface interrupt */ -#define IRQ_USBH2 PXA_IRQ(2) /* USB Host interrupt 1 (OHCI) */ -#define IRQ_USBH1 PXA_IRQ(3) /* USB Host interrupt 2 (non-OHCI) */ +#define IRQ_USBH2 PXA_IRQ(2) /* USB Host interrupt 1 (OHCI,PXA27x) */ +#define IRQ_USBH1 PXA_IRQ(3) /* USB Host interrupt 2 (non-OHCI,PXA27x) */ #define IRQ_KEYPAD PXA_IRQ(4) /* Key pad controller */ -#define IRQ_MEMSTK PXA_IRQ(5) /* Memory Stick interrupt */ +#define IRQ_MEMSTK PXA_IRQ(5) /* Memory Stick interrupt (PXA27x) */ +#define IRQ_ACIPC0 PXA_IRQ(5) /* AP-CP Communication (PXA930) */ #define IRQ_PWRI2C PXA_IRQ(6) /* Power I2C interrupt */ -#endif - #define IRQ_HWUART PXA_IRQ(7) /* HWUART Transmit/Receive/Error (PXA26x) */ #define IRQ_OST_4_11 PXA_IRQ(7) /* OS timer 4-11 matches (PXA27x) */ #define IRQ_GPIO0 PXA_IRQ(8) /* GPIO0 Edge Detect */ @@ -38,7 +36,8 @@ #define IRQ_GPIO_2_x PXA_IRQ(10) /* GPIO[2-x] Edge Detect */ #define IRQ_USB PXA_IRQ(11) /* USB Service */ #define IRQ_PMU PXA_IRQ(12) /* Performance Monitoring Unit */ -#define IRQ_I2S PXA_IRQ(13) /* I2S Interrupt */ +#define IRQ_I2S PXA_IRQ(13) /* I2S Interrupt (PXA27x) */ +#define IRQ_SSP4 PXA_IRQ(13) /* SSP4 service request (PXA3xx) */ #define IRQ_AC97 PXA_IRQ(14) /* AC97 Interrupt */ #define IRQ_ASSP PXA_IRQ(15) /* Audio SSP Service Request (PXA25x) */ #define IRQ_USIM PXA_IRQ(15) /* Smart Card interface interrupt (PXA27x) */ @@ -47,6 +46,7 @@ #define IRQ_LCD PXA_IRQ(17) /* LCD Controller Service Request */ #define IRQ_I2C PXA_IRQ(18) /* I2C Service Request */ #define IRQ_ICP PXA_IRQ(19) /* ICP Transmit/Receive/Error */ +#define IRQ_ACIPC2 PXA_IRQ(19) /* AP-CP Communication (PXA930) */ #define IRQ_STUART PXA_IRQ(20) /* STUART Transmit/Receive/Error */ #define IRQ_BTUART PXA_IRQ(21) /* BTUART Transmit/Receive/Error */ #define IRQ_FFUART PXA_IRQ(22) /* FFUART Transmit/Receive/Error*/ @@ -60,19 +60,17 @@ #define IRQ_RTC1Hz PXA_IRQ(30) /* RTC HZ Clock Tick */ #define IRQ_RTCAlrm PXA_IRQ(31) /* RTC Alarm */ -#if defined(CONFIG_PXA27x) || defined(CONFIG_PXA3xx) #define IRQ_TPM PXA_IRQ(32) /* TPM interrupt */ #define IRQ_CAMERA PXA_IRQ(33) /* Camera Interface */ -#endif - -#ifdef CONFIG_PXA3xx -#define IRQ_SSP4 PXA_IRQ(13) /* SSP4 service request */ #define IRQ_CIR PXA_IRQ(34) /* Consumer IR */ #define IRQ_COMM_WDT PXA_IRQ(35) /* Comm WDT interrupt */ #define IRQ_TSI PXA_IRQ(36) /* Touch Screen Interface (PXA320) */ +#define IRQ_ENHROT PXA_IRQ(37) /* Enhanced Rotary (PXA930) */ #define IRQ_USIM2 PXA_IRQ(38) /* USIM2 Controller */ -#define IRQ_GCU PXA_IRQ(39) /* Graphics Controller */ +#define IRQ_GCU PXA_IRQ(39) /* Graphics Controller (PXA3xx) */ +#define IRQ_ACIPC1 PXA_IRQ(40) /* AP-CP Communication (PXA930) */ #define IRQ_MMC2 PXA_IRQ(41) /* MMC2 Controller */ +#define IRQ_TRKBALL PXA_IRQ(43) /* Track Ball (PXA930) */ #define IRQ_1WIRE PXA_IRQ(44) /* 1-Wire Controller */ #define IRQ_NAND PXA_IRQ(45) /* NAND Controller */ #define IRQ_USB2 PXA_IRQ(46) /* USB 2.0 Device Controller */ @@ -80,30 +78,14 @@ #define IRQ_WAKEUP1 PXA_IRQ(50) /* EXT_WAKEUP1 */ #define IRQ_DMEMC PXA_IRQ(51) /* Dynamic Memory Controller */ #define IRQ_MMC3 PXA_IRQ(55) /* MMC3 Controller (PXA310) */ -#endif -#ifdef CONFIG_CPU_PXA935 #define IRQ_U2O PXA_IRQ(64) /* USB OTG 2.0 Controller (PXA935) */ #define IRQ_U2H PXA_IRQ(65) /* USB Host 2.0 Controller (PXA935) */ - -#define IRQ_MMC3_PXA935 PXA_IRQ(72) /* MMC3 Controller (PXA935) */ -#define IRQ_MMC4_PXA935 PXA_IRQ(73) /* MMC4 Controller (PXA935) */ -#define IRQ_MMC5_PXA935 PXA_IRQ(74) /* MMC5 Controller (PXA935) */ - +#define IRQ_PXA935_MMC0 PXA_IRQ(72) /* MMC0 Controller (PXA935) */ +#define IRQ_PXA935_MMC1 PXA_IRQ(73) /* MMC1 Controller (PXA935) */ +#define IRQ_PXA935_MMC2 PXA_IRQ(74) /* MMC2 Controller (PXA935) */ +#define IRQ_PXA955_MMC3 PXA_IRQ(75) /* MMC3 Controller (PXA955) */ #define IRQ_U2P PXA_IRQ(93) /* USB PHY D+/D- Lines (PXA935) */ -#endif - -#ifdef CONFIG_CPU_PXA930 -#define IRQ_ENHROT PXA_IRQ(37) /* Enhanced Rotary (PXA930) */ -#define IRQ_ACIPC0 PXA_IRQ(5) -#define IRQ_ACIPC1 PXA_IRQ(40) -#define IRQ_ACIPC2 PXA_IRQ(19) -#define IRQ_TRKBALL PXA_IRQ(43) /* Track Ball */ -#endif - -#ifdef CONFIG_CPU_PXA950 -#define IRQ_GC500 PXA_IRQ(70) /* Graphics Controller (PXA950) */ -#endif #define PXA_GPIO_IRQ_BASE PXA_IRQ(96) #define PXA_GPIO_IRQ_NUM (192) diff --git a/arch/arm/mach-pxa/include/mach/pxa2xx-regs.h b/arch/arm/mach-pxa/include/mach/pxa2xx-regs.h index 4fcddd9..ee6ced1 100644 --- a/arch/arm/mach-pxa/include/mach/pxa2xx-regs.h +++ b/arch/arm/mach-pxa/include/mach/pxa2xx-regs.h @@ -17,72 +17,6 @@ #include <mach/hardware.h> /* - * PXA Chip selects - */ - -#define PXA_CS0_PHYS 0x00000000 -#define PXA_CS1_PHYS 0x04000000 -#define PXA_CS2_PHYS 0x08000000 -#define PXA_CS3_PHYS 0x0C000000 -#define PXA_CS4_PHYS 0x10000000 -#define PXA_CS5_PHYS 0x14000000 - -/* - * Memory controller - */ - -#define MDCNFG __REG(0x48000000) /* SDRAM Configuration Register 0 */ -#define MDREFR __REG(0x48000004) /* SDRAM Refresh Control Register */ -#define MSC0 __REG(0x48000008) /* Static Memory Control Register 0 */ -#define MSC1 __REG(0x4800000C) /* Static Memory Control Register 1 */ -#define MSC2 __REG(0x48000010) /* Static Memory Control Register 2 */ -#define MECR __REG(0x48000014) /* Expansion Memory (PCMCIA/Compact Flash) Bus Configuration */ -#define SXLCR __REG(0x48000018) /* LCR value to be written to SDRAM-Timing Synchronous Flash */ -#define SXCNFG __REG(0x4800001C) /* Synchronous Static Memory Control Register */ -#define SXMRS __REG(0x48000024) /* MRS value to be written to Synchronous Flash or SMROM */ -#define MCMEM0 __REG(0x48000028) /* Card interface Common Memory Space Socket 0 Timing */ -#define MCMEM1 __REG(0x4800002C) /* Card interface Common Memory Space Socket 1 Timing */ -#define MCATT0 __REG(0x48000030) /* Card interface Attribute Space Socket 0 Timing Configuration */ -#define MCATT1 __REG(0x48000034) /* Card interface Attribute Space Socket 1 Timing Configuration */ -#define MCIO0 __REG(0x48000038) /* Card interface I/O Space Socket 0 Timing Configuration */ -#define MCIO1 __REG(0x4800003C) /* Card interface I/O Space Socket 1 Timing Configuration */ -#define MDMRS __REG(0x48000040) /* MRS value to be written to SDRAM */ -#define BOOT_DEF __REG(0x48000044) /* Read-Only Boot-Time Register. Contains BOOT_SEL and PKG_SEL */ - -/* - * More handy macros for PCMCIA - * - * Arg is socket number - */ -#define MCMEM(s) __REG2(0x48000028, (s)<<2 ) /* Card interface Common Memory Space Socket s Timing */ -#define MCATT(s) __REG2(0x48000030, (s)<<2 ) /* Card interface Attribute Space Socket s Timing Configuration */ -#define MCIO(s) __REG2(0x48000038, (s)<<2 ) /* Card interface I/O Space Socket s Timing Configuration */ - -/* MECR register defines */ -#define MECR_NOS (1 << 0) /* Number Of Sockets: 0 -> 1 sock, 1 -> 2 sock */ -#define MECR_CIT (1 << 1) /* Card Is There: 0 -> no card, 1 -> card inserted */ - -#define MDCNFG_DE0 (1 << 0) /* SDRAM Bank 0 Enable */ -#define MDCNFG_DE1 (1 << 1) /* SDRAM Bank 1 Enable */ -#define MDCNFG_DE2 (1 << 16) /* SDRAM Bank 2 Enable */ -#define MDCNFG_DE3 (1 << 17) /* SDRAM Bank 3 Enable */ - -#define MDREFR_K0DB4 (1 << 29) /* SDCLK0 Divide by 4 Control/Status */ -#define MDREFR_K2FREE (1 << 25) /* SDRAM Free-Running Control */ -#define MDREFR_K1FREE (1 << 24) /* SDRAM Free-Running Control */ -#define MDREFR_K0FREE (1 << 23) /* SDRAM Free-Running Control */ -#define MDREFR_SLFRSH (1 << 22) /* SDRAM Self-Refresh Control/Status */ -#define MDREFR_APD (1 << 20) /* SDRAM/SSRAM Auto-Power-Down Enable */ -#define MDREFR_K2DB2 (1 << 19) /* SDCLK2 Divide by 2 Control/Status */ -#define MDREFR_K2RUN (1 << 18) /* SDCLK2 Run Control/Status */ -#define MDREFR_K1DB2 (1 << 17) /* SDCLK1 Divide by 2 Control/Status */ -#define MDREFR_K1RUN (1 << 16) /* SDCLK1 Run Control/Status */ -#define MDREFR_E1PIN (1 << 15) /* SDCKE1 Level Control/Status */ -#define MDREFR_K0DB2 (1 << 14) /* SDCLK0 Divide by 2 Control/Status */ -#define MDREFR_K0RUN (1 << 13) /* SDCLK0 Run Control/Status */ -#define MDREFR_E0PIN (1 << 12) /* SDCKE0 Level Control/Status */ - -/* * Power Manager */ diff --git a/arch/arm/mach-pxa/include/mach/pxa2xx_spi.h b/arch/arm/mach-pxa/include/mach/pxa2xx_spi.h deleted file mode 100644 index b87cecd..0000000 --- a/arch/arm/mach-pxa/include/mach/pxa2xx_spi.h +++ /dev/null @@ -1,47 +0,0 @@ -/* - * Copyright (C) 2005 Stephen Street / StreetFire Sound Labs - * - * This program is free software; you can redistribute it and/or modify - * it under the terms of the GNU General Public License as published by - * the Free Software Foundation; either version 2 of the License, or - * (at your option) any later version. - * - * This program is distributed in the hope that it will be useful, - * but WITHOUT ANY WARRANTY; without even the implied warranty of - * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the - * GNU General Public License for more details. - * - * You should have received a copy of the GNU General Public License - * along with this program; if not, write to the Free Software - * Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA. - */ - -#ifndef PXA2XX_SPI_H_ -#define PXA2XX_SPI_H_ - -#define PXA2XX_CS_ASSERT (0x01) -#define PXA2XX_CS_DEASSERT (0x02) - -/* device.platform_data for SSP controller devices */ -struct pxa2xx_spi_master { - u32 clock_enable; - u16 num_chipselect; - u8 enable_dma; -}; - -/* spi_board_info.controller_data for SPI slave devices, - * copied to spi_device.platform_data ... mostly for dma tuning - */ -struct pxa2xx_spi_chip { - u8 tx_threshold; - u8 rx_threshold; - u8 dma_burst_size; - u32 timeout; - u8 enable_loopback; - int gpio_cs; - void (*cs_control)(u32 command); -}; - -extern void pxa2xx_set_spi_info(unsigned id, struct pxa2xx_spi_master *info); - -#endif /*PXA2XX_SPI_H_*/ diff --git a/arch/arm/mach-pxa/include/mach/pxa3xx-regs.h b/arch/arm/mach-pxa/include/mach/pxa3xx-regs.h index e91d63c..e4fb4668 100644 --- a/arch/arm/mach-pxa/include/mach/pxa3xx-regs.h +++ b/arch/arm/mach-pxa/include/mach/pxa3xx-regs.h @@ -16,15 +16,6 @@ #include <mach/hardware.h> /* - * Static Chip Selects - */ - -#define PXA300_CS0_PHYS (0x00000000) /* PXA300/PXA310 _only_ */ -#define PXA300_CS1_PHYS (0x30000000) /* PXA300/PXA310 _only_ */ -#define PXA3xx_CS2_PHYS (0x10000000) -#define PXA3xx_CS3_PHYS (0x14000000) - -/* * Oscillator Configuration Register (OSCC) */ #define OSCC __REG(0x41350000) /* Oscillator Configuration Register */ diff --git a/arch/arm/mach-pxa/include/mach/regs-intc.h b/arch/arm/mach-pxa/include/mach/regs-intc.h index 68464ce..662288e 100644 --- a/arch/arm/mach-pxa/include/mach/regs-intc.h +++ b/arch/arm/mach-pxa/include/mach/regs-intc.h @@ -27,8 +27,4 @@ #define ICFP3 __REG(0x40D0013C) /* Interrupt Controller FIQ Pending Register 3 */ #define ICPR3 __REG(0x40D00140) /* Interrupt Controller Pending Register 3 */ -#define IPR(x) __REG(0x40D0001C + (x < 32 ? (x << 2) \ - : (x < 64 ? (0x94 + ((x - 32) << 2)) \ - : (0x128 + ((x - 64) << 2))))) - #endif /* __ASM_MACH_REGS_INTC_H */ diff --git a/arch/arm/mach-pxa/include/mach/smemc.h b/arch/arm/mach-pxa/include/mach/smemc.h new file mode 100644 index 0000000..654adc9 --- /dev/null +++ b/arch/arm/mach-pxa/include/mach/smemc.h @@ -0,0 +1,74 @@ +/* + * Static memory controller register definitions for PXA CPUs + * + * Copyright (C) 2010 Marek Vasut <marek.vasut@gmail.com> + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + */ + +#ifndef __SMEMC_REGS_H +#define __SMEMC_REGS_H + +#define PXA2XX_SMEMC_BASE 0x48000000 +#define PXA3XX_SMEMC_BASE 0x4a000000 +#define SMEMC_VIRT 0xf6000000 + +#define MDCNFG (SMEMC_VIRT + 0x00) /* SDRAM Configuration Register 0 */ +#define MDREFR (SMEMC_VIRT + 0x04) /* SDRAM Refresh Control Register */ +#define MSC0 (SMEMC_VIRT + 0x08) /* Static Memory Control Register 0 */ +#define MSC1 (SMEMC_VIRT + 0x0C) /* Static Memory Control Register 1 */ +#define MSC2 (SMEMC_VIRT + 0x10) /* Static Memory Control Register 2 */ +#define MECR (SMEMC_VIRT + 0x14) /* Expansion Memory (PCMCIA/Compact Flash) Bus Configuration */ +#define SXLCR (SMEMC_VIRT + 0x18) /* LCR value to be written to SDRAM-Timing Synchronous Flash */ +#define SXCNFG (SMEMC_VIRT + 0x1C) /* Synchronous Static Memory Control Register */ +#define SXMRS (SMEMC_VIRT + 0x24) /* MRS value to be written to Synchronous Flash or SMROM */ +#define MCMEM0 (SMEMC_VIRT + 0x28) /* Card interface Common Memory Space Socket 0 Timing */ +#define MCMEM1 (SMEMC_VIRT + 0x2C) /* Card interface Common Memory Space Socket 1 Timing */ +#define MCATT0 (SMEMC_VIRT + 0x30) /* Card interface Attribute Space Socket 0 Timing Configuration */ +#define MCATT1 (SMEMC_VIRT + 0x34) /* Card interface Attribute Space Socket 1 Timing Configuration */ +#define MCIO0 (SMEMC_VIRT + 0x38) /* Card interface I/O Space Socket 0 Timing Configuration */ +#define MCIO1 (SMEMC_VIRT + 0x3C) /* Card interface I/O Space Socket 1 Timing Configuration */ +#define MDMRS (SMEMC_VIRT + 0x40) /* MRS value to be written to SDRAM */ +#define BOOT_DEF (SMEMC_VIRT + 0x44) /* Read-Only Boot-Time Register. Contains BOOT_SEL and PKG_SEL */ +#define MEMCLKCFG (SMEMC_VIRT + 0x68) /* Clock Configuration */ +#define CSADRCFG0 (SMEMC_VIRT + 0x80) /* Address Configuration Register for CS0 */ +#define CSADRCFG1 (SMEMC_VIRT + 0x84) /* Address Configuration Register for CS1 */ +#define CSADRCFG2 (SMEMC_VIRT + 0x88) /* Address Configuration Register for CS2 */ +#define CSADRCFG3 (SMEMC_VIRT + 0x8C) /* Address Configuration Register for CS3 */ + +/* + * More handy macros for PCMCIA + * + * Arg is socket number + */ +#define MCMEM(s) (SMEMC_VIRT + 0x28 + ((s)<<2)) /* Card interface Common Memory Space Socket s Timing */ +#define MCATT(s) (SMEMC_VIRT + 0x30 + ((s)<<2)) /* Card interface Attribute Space Socket s Timing Configuration */ +#define MCIO(s) (SMEMC_VIRT + 0x38 + ((s)<<2)) /* Card interface I/O Space Socket s Timing Configuration */ + +/* MECR register defines */ +#define MECR_NOS (1 << 0) /* Number Of Sockets: 0 -> 1 sock, 1 -> 2 sock */ +#define MECR_CIT (1 << 1) /* Card Is There: 0 -> no card, 1 -> card inserted */ + +#define MDCNFG_DE0 (1 << 0) /* SDRAM Bank 0 Enable */ +#define MDCNFG_DE1 (1 << 1) /* SDRAM Bank 1 Enable */ +#define MDCNFG_DE2 (1 << 16) /* SDRAM Bank 2 Enable */ +#define MDCNFG_DE3 (1 << 17) /* SDRAM Bank 3 Enable */ + +#define MDREFR_K0DB4 (1 << 29) /* SDCLK0 Divide by 4 Control/Status */ +#define MDREFR_K2FREE (1 << 25) /* SDRAM Free-Running Control */ +#define MDREFR_K1FREE (1 << 24) /* SDRAM Free-Running Control */ +#define MDREFR_K0FREE (1 << 23) /* SDRAM Free-Running Control */ +#define MDREFR_SLFRSH (1 << 22) /* SDRAM Self-Refresh Control/Status */ +#define MDREFR_APD (1 << 20) /* SDRAM/SSRAM Auto-Power-Down Enable */ +#define MDREFR_K2DB2 (1 << 19) /* SDCLK2 Divide by 2 Control/Status */ +#define MDREFR_K2RUN (1 << 18) /* SDCLK2 Run Control/Status */ +#define MDREFR_K1DB2 (1 << 17) /* SDCLK1 Divide by 2 Control/Status */ +#define MDREFR_K1RUN (1 << 16) /* SDCLK1 Run Control/Status */ +#define MDREFR_E1PIN (1 << 15) /* SDCKE1 Level Control/Status */ +#define MDREFR_K0DB2 (1 << 14) /* SDCLK0 Divide by 2 Control/Status */ +#define MDREFR_K0RUN (1 << 13) /* SDCLK0 Run Control/Status */ +#define MDREFR_E0PIN (1 << 12) /* SDCKE0 Level Control/Status */ + +#endif diff --git a/arch/arm/mach-pxa/irq.c b/arch/arm/mach-pxa/irq.c index 1beb40f..54e91c9 100644 --- a/arch/arm/mach-pxa/irq.c +++ b/arch/arm/mach-pxa/irq.c @@ -16,20 +16,31 @@ #include <linux/module.h> #include <linux/interrupt.h> #include <linux/sysdev.h> +#include <linux/io.h> +#include <linux/irq.h> #include <mach/hardware.h> -#include <asm/irq.h> -#include <asm/mach/irq.h> +#include <mach/irqs.h> #include <mach/gpio.h> -#include <mach/regs-intc.h> #include "generic.h" -#define MAX_INTERNAL_IRQS 128 +#define IRQ_BASE (void __iomem *)io_p2v(0x40d00000) + +#define ICIP (0x000) +#define ICMR (0x004) +#define ICLR (0x008) +#define ICFR (0x00c) +#define ICPR (0x010) +#define ICCR (0x014) +#define ICHP (0x018) +#define IPR(i) (((i) < 32) ? (0x01c + ((i) << 2)) : \ + ((i) < 64) ? (0x0b0 + (((i) - 32) << 2)) : \ + (0x144 + (((i) - 64) << 2))) +#define IPR_VALID (1 << 31) +#define IRQ_BIT(n) (((n) - PXA_IRQ(0)) & 0x1f) -#define IRQ_BIT(n) (((n) - PXA_IRQ(0)) & 0x1f) -#define _ICMR(n) (*((((n) - PXA_IRQ(0)) & ~0x1f) ? &ICMR2 : &ICMR)) -#define _ICLR(n) (*((((n) - PXA_IRQ(0)) & ~0x1f) ? &ICLR2 : &ICLR)) +#define MAX_INTERNAL_IRQS 128 /* * This is for peripheral IRQs internal to the PXA chip. @@ -37,14 +48,27 @@ static int pxa_internal_irq_nr; +static inline int cpu_has_ipr(void) +{ + return !cpu_is_pxa25x(); +} + static void pxa_mask_irq(unsigned int irq) { - _ICMR(irq) &= ~(1 << IRQ_BIT(irq)); + void __iomem *base = get_irq_chip_data(irq); + uint32_t icmr = __raw_readl(base + ICMR); + + icmr &= ~(1 << IRQ_BIT(irq)); + __raw_writel(icmr, base + ICMR); } static void pxa_unmask_irq(unsigned int irq) { - _ICMR(irq) |= 1 << IRQ_BIT(irq); + void __iomem *base = get_irq_chip_data(irq); + uint32_t icmr = __raw_readl(base + ICMR); + + icmr |= 1 << IRQ_BIT(irq); + __raw_writel(icmr, base + ICMR); } static struct irq_chip pxa_internal_irq_chip = { @@ -86,12 +110,16 @@ static void pxa_ack_low_gpio(unsigned int irq) static void pxa_mask_low_gpio(unsigned int irq) { - ICMR &= ~(1 << (irq - PXA_IRQ(0))); + struct irq_desc *desc = irq_to_desc(irq); + + desc->chip->mask(irq); } static void pxa_unmask_low_gpio(unsigned int irq) { - ICMR |= 1 << (irq - PXA_IRQ(0)); + struct irq_desc *desc = irq_to_desc(irq); + + desc->chip->unmask(irq); } static struct irq_chip pxa_low_gpio_chip = { @@ -120,33 +148,45 @@ static void __init pxa_init_low_gpio_irq(set_wake_t fn) pxa_low_gpio_chip.set_wake = fn; } +static inline void __iomem *irq_base(int i) +{ + static unsigned long phys_base[] = { + 0x40d00000, + 0x40d0009c, + 0x40d00130, + }; + + return (void __iomem *)io_p2v(phys_base[i >> 5]); +} + void __init pxa_init_irq(int irq_nr, set_wake_t fn) { - int irq, i; + int irq, i, n; BUG_ON(irq_nr > MAX_INTERNAL_IRQS); pxa_internal_irq_nr = irq_nr; - for (irq = PXA_IRQ(0); irq < PXA_IRQ(irq_nr); irq += 32) { - _ICMR(irq) = 0; /* disable all IRQs */ - _ICLR(irq) = 0; /* all IRQs are IRQ, not FIQ */ - } - - /* initialize interrupt priority */ - if (cpu_is_pxa27x() || cpu_is_pxa3xx()) { - for (i = 0; i < irq_nr; i++) - IPR(i) = i | (1 << 31); + for (n = 0; n < irq_nr; n += 32) { + void __iomem *base = irq_base(n); + + __raw_writel(0, base + ICMR); /* disable all IRQs */ + __raw_writel(0, base + ICLR); /* all IRQs are IRQ, not FIQ */ + for (i = n; (i < (n + 32)) && (i < irq_nr); i++) { + /* initialize interrupt priority */ + if (cpu_has_ipr()) + __raw_writel(i | IPR_VALID, IRQ_BASE + IPR(i)); + + irq = PXA_IRQ(i); + set_irq_chip(irq, &pxa_internal_irq_chip); + set_irq_chip_data(irq, base); + set_irq_handler(irq, handle_level_irq); + set_irq_flags(irq, IRQF_VALID); + } } /* only unmasked interrupts kick us out of idle */ - ICCR = 1; - - for (irq = PXA_IRQ(0); irq < PXA_IRQ(irq_nr); irq++) { - set_irq_chip(irq, &pxa_internal_irq_chip); - set_irq_handler(irq, handle_level_irq); - set_irq_flags(irq, IRQF_VALID); - } + __raw_writel(1, irq_base(0) + ICCR); pxa_internal_irq_chip.set_wake = fn; pxa_init_low_gpio_irq(fn); @@ -158,16 +198,18 @@ static unsigned long saved_ipr[MAX_INTERNAL_IRQS]; static int pxa_irq_suspend(struct sys_device *dev, pm_message_t state) { - int i, irq = PXA_IRQ(0); + int i; - for (i = 0; irq < PXA_IRQ(pxa_internal_irq_nr); i++, irq += 32) { - saved_icmr[i] = _ICMR(irq); - _ICMR(irq) = 0; + for (i = 0; i < pxa_internal_irq_nr; i += 32) { + void __iomem *base = irq_base(i); + + saved_icmr[i] = __raw_readl(base + ICMR); + __raw_writel(0, base + ICMR); } - if (cpu_is_pxa27x() || cpu_is_pxa3xx()) { + if (cpu_has_ipr()) { for (i = 0; i < pxa_internal_irq_nr; i++) - saved_ipr[i] = IPR(i); + saved_ipr[i] = __raw_readl(IRQ_BASE + IPR(i)); } return 0; @@ -175,19 +217,20 @@ static int pxa_irq_suspend(struct sys_device *dev, pm_message_t state) static int pxa_irq_resume(struct sys_device *dev) { - int i, irq = PXA_IRQ(0); + int i; - if (cpu_is_pxa27x() || cpu_is_pxa3xx()) { - for (i = 0; i < pxa_internal_irq_nr; i++) - IPR(i) = saved_ipr[i]; - } + for (i = 0; i < pxa_internal_irq_nr; i += 32) { + void __iomem *base = irq_base(i); - for (i = 0; irq < PXA_IRQ(pxa_internal_irq_nr); i++, irq += 32) { - _ICMR(irq) = saved_icmr[i]; - _ICLR(irq) = 0; + __raw_writel(saved_icmr[i], base + ICMR); + __raw_writel(0, base + ICLR); } - ICCR = 1; + if (!cpu_is_pxa25x()) + for (i = 0; i < pxa_internal_irq_nr; i++) + __raw_writel(saved_ipr[i], IRQ_BASE + IPR(i)); + + __raw_writel(1, IRQ_BASE + ICCR); return 0; } #else diff --git a/arch/arm/mach-pxa/littleton.c b/arch/arm/mach-pxa/littleton.c index 41aa89e..ccb7bfa 100644 --- a/arch/arm/mach-pxa/littleton.c +++ b/arch/arm/mach-pxa/littleton.c @@ -22,6 +22,7 @@ #include <linux/clk.h> #include <linux/gpio.h> #include <linux/spi/spi.h> +#include <linux/spi/pxa2xx_spi.h> #include <linux/smc91x.h> #include <linux/i2c.h> #include <linux/leds.h> @@ -42,7 +43,6 @@ #include <mach/pxa300.h> #include <mach/pxafb.h> #include <mach/mmc.h> -#include <mach/pxa2xx_spi.h> #include <plat/pxa27x_keypad.h> #include <mach/littleton.h> #include <plat/i2c.h> @@ -438,7 +438,7 @@ static void __init littleton_init(void) MACHINE_START(LITTLETON, "Marvell Form Factor Development Platform (aka Littleton)") .boot_params = 0xa0000100, - .map_io = pxa_map_io, + .map_io = pxa3xx_map_io, .nr_irqs = LITTLETON_NR_IRQS, .init_irq = pxa3xx_init_irq, .timer = &pxa_timer, diff --git a/arch/arm/mach-pxa/lpd270.c b/arch/arm/mach-pxa/lpd270.c index 623af02..8ab62a6 100644 --- a/arch/arm/mach-pxa/lpd270.c +++ b/arch/arm/mach-pxa/lpd270.c @@ -46,6 +46,7 @@ #include <mach/mmc.h> #include <mach/irda.h> #include <mach/ohci.h> +#include <mach/smemc.h> #include "generic.h" #include "devices.h" @@ -463,7 +464,7 @@ static void __init lpd270_init(void) pxa_set_btuart_info(NULL); pxa_set_stuart_info(NULL); - lpd270_flash_data[0].width = (BOOT_DEF & 1) ? 2 : 4; + lpd270_flash_data[0].width = (__raw_readl(BOOT_DEF) & 1) ? 2 : 4; lpd270_flash_data[1].width = 4; /* @@ -495,7 +496,7 @@ static struct map_desc lpd270_io_desc[] __initdata = { static void __init lpd270_map_io(void) { - pxa_map_io(); + pxa27x_map_io(); iotable_init(lpd270_io_desc, ARRAY_SIZE(lpd270_io_desc)); /* for use I SRAM as framebuffer. */ diff --git a/arch/arm/mach-pxa/lubbock.c b/arch/arm/mach-pxa/lubbock.c index 1499493..3072dbe 100644 --- a/arch/arm/mach-pxa/lubbock.c +++ b/arch/arm/mach-pxa/lubbock.c @@ -25,7 +25,7 @@ #include <linux/spi/spi.h> #include <linux/spi/ads7846.h> -#include <mach/pxa2xx_spi.h> +#include <linux/spi/pxa2xx_spi.h> #include <asm/setup.h> #include <asm/memory.h> @@ -50,6 +50,7 @@ #include <mach/pxafb.h> #include <mach/mmc.h> #include <mach/pm.h> +#include <mach/smemc.h> #include "generic.h" #include "clock.h" @@ -525,7 +526,7 @@ static void __init lubbock_init(void) pxa_set_ac97_info(NULL); lubbock_flash_data[0].width = lubbock_flash_data[1].width = - (BOOT_DEF & 1) ? 2 : 4; + (__raw_readl(BOOT_DEF) & 1) ? 2 : 4; /* Compensate for the nROMBT switch which swaps the flash banks */ printk(KERN_NOTICE "Lubbock configured to boot from %s (bank %d)\n", flashboot?"Flash":"ROM", flashboot); @@ -549,7 +550,7 @@ static struct map_desc lubbock_io_desc[] __initdata = { static void __init lubbock_map_io(void) { - pxa_map_io(); + pxa25x_map_io(); iotable_init(lubbock_io_desc, ARRAY_SIZE(lubbock_io_desc)); PCFR |= PCFR_OPDE; diff --git a/arch/arm/mach-pxa/magician.c b/arch/arm/mach-pxa/magician.c index 9066376..41198f0 100644 --- a/arch/arm/mach-pxa/magician.c +++ b/arch/arm/mach-pxa/magician.c @@ -765,7 +765,7 @@ static void __init magician_init(void) MACHINE_START(MAGICIAN, "HTC Magician") .boot_params = 0xa0000100, - .map_io = pxa_map_io, + .map_io = pxa27x_map_io, .nr_irqs = MAGICIAN_NR_IRQS, .init_irq = pxa27x_init_irq, .init_machine = magician_init, diff --git a/arch/arm/mach-pxa/mainstone.c b/arch/arm/mach-pxa/mainstone.c index a980a5c..740c035 100644 --- a/arch/arm/mach-pxa/mainstone.c +++ b/arch/arm/mach-pxa/mainstone.c @@ -51,6 +51,7 @@ #include <mach/irda.h> #include <mach/ohci.h> #include <plat/pxa27x_keypad.h> +#include <mach/smemc.h> #include "generic.h" #include "devices.h" @@ -565,7 +566,7 @@ static void __init mainstone_init(void) pxa_set_btuart_info(NULL); pxa_set_stuart_info(NULL); - mst_flash_data[0].width = (BOOT_DEF & 1) ? 2 : 4; + mst_flash_data[0].width = (__raw_readl(BOOT_DEF) & 1) ? 2 : 4; mst_flash_data[1].width = 4; /* Compensate for SW7 which swaps the flash banks */ @@ -614,7 +615,7 @@ static struct map_desc mainstone_io_desc[] __initdata = { static void __init mainstone_map_io(void) { - pxa_map_io(); + pxa27x_map_io(); iotable_init(mainstone_io_desc, ARRAY_SIZE(mainstone_io_desc)); /* for use I SRAM as framebuffer. */ diff --git a/arch/arm/mach-pxa/mioa701.c b/arch/arm/mach-pxa/mioa701.c index f5fb915..faafea3 100644 --- a/arch/arm/mach-pxa/mioa701.c +++ b/arch/arm/mach-pxa/mioa701.c @@ -819,7 +819,7 @@ static void mioa701_machine_exit(void) MACHINE_START(MIOA701, "MIO A701") .boot_params = 0xa0000100, - .map_io = &pxa_map_io, + .map_io = &pxa27x_map_io, .init_irq = &pxa27x_init_irq, .init_machine = mioa701_machine_init, .timer = &pxa_timer, diff --git a/arch/arm/mach-pxa/mp900.c b/arch/arm/mach-pxa/mp900.c index 116167aa..59cce78 100644 --- a/arch/arm/mach-pxa/mp900.c +++ b/arch/arm/mach-pxa/mp900.c @@ -94,7 +94,7 @@ static void __init mp900c_init(void) MACHINE_START(NEC_MP900, "MobilePro900/C") .boot_params = 0xa0220100, .timer = &pxa_timer, - .map_io = pxa_map_io, + .map_io = pxa25x_map_io, .init_irq = pxa25x_init_irq, .init_machine = mp900c_init, MACHINE_END diff --git a/arch/arm/mach-pxa/palmld.c b/arch/arm/mach-pxa/palmld.c index ce092c5..a6f898c 100644 --- a/arch/arm/mach-pxa/palmld.c +++ b/arch/arm/mach-pxa/palmld.c @@ -313,7 +313,7 @@ static struct map_desc palmld_io_desc[] __initdata = { static void __init palmld_map_io(void) { - pxa_map_io(); + pxa27x_map_io(); iotable_init(palmld_io_desc, ARRAY_SIZE(palmld_io_desc)); } diff --git a/arch/arm/mach-pxa/palmt5.c b/arch/arm/mach-pxa/palmt5.c index 862da81..df4d7d0 100644 --- a/arch/arm/mach-pxa/palmt5.c +++ b/arch/arm/mach-pxa/palmt5.c @@ -203,7 +203,7 @@ static void __init palmt5_init(void) MACHINE_START(PALMT5, "Palm Tungsten|T5") .boot_params = 0xa0000100, - .map_io = pxa_map_io, + .map_io = pxa27x_map_io, .reserve = palmt5_reserve, .init_irq = pxa27x_init_irq, .timer = &pxa_timer, diff --git a/arch/arm/mach-pxa/palmtc.c b/arch/arm/mach-pxa/palmtc.c index 2131d58..a09a237 100644 --- a/arch/arm/mach-pxa/palmtc.c +++ b/arch/arm/mach-pxa/palmtc.c @@ -25,6 +25,7 @@ #include <linux/power_supply.h> #include <linux/gpio_keys.h> #include <linux/mtd/physmap.h> +#include <linux/usb/gpio_vbus.h> #include <asm/mach-types.h> #include <asm/mach/arch.h> @@ -116,6 +117,7 @@ static unsigned long palmtc_pin_config[] __initdata = { /****************************************************************************** * SD/MMC card controller ******************************************************************************/ +#if defined(CONFIG_MMC_PXA) || defined(CONFIG_MMC_PXA_MODULE) static struct pxamci_platform_data palmtc_mci_platform_data = { .ocr_mask = MMC_VDD_32_33 | MMC_VDD_33_34, .gpio_power = GPIO_NR_PALMTC_SD_POWER, @@ -124,9 +126,18 @@ static struct pxamci_platform_data palmtc_mci_platform_data = { .detect_delay_ms = 200, }; +static void __init palmtc_mmc_init(void) +{ + pxa_set_mci_info(&palmtc_mci_platform_data); +} +#else +static inline void palmtc_mmc_init(void) {} +#endif + /****************************************************************************** * GPIO keys ******************************************************************************/ +#if defined(CONFIG_KEYBOARD_GPIO) || defined(CONFIG_KEYBOARD_GPIO_MODULE) static struct gpio_keys_button palmtc_pxa_buttons[] = { {KEY_F8, GPIO_NR_PALMTC_HOTSYNC_BUTTON, 1, "HotSync Button", EV_KEY, 1}, }; @@ -144,9 +155,18 @@ static struct platform_device palmtc_pxa_keys = { }, }; +static void __init palmtc_keys_init(void) +{ + platform_device_register(&palmtc_pxa_keys); +} +#else +static inline void palmtc_keys_init(void) {} +#endif + /****************************************************************************** * Backlight ******************************************************************************/ +#if defined(CONFIG_BACKLIGHT_PWM) || defined(CONFIG_BACKLIGHT_PWM_MODULE) static int palmtc_backlight_init(struct device *dev) { int ret; @@ -196,17 +216,35 @@ static struct platform_device palmtc_backlight = { }, }; +static void __init palmtc_pwm_init(void) +{ + platform_device_register(&palmtc_backlight); +} +#else +static inline void palmtc_pwm_init(void) {} +#endif + /****************************************************************************** * IrDA ******************************************************************************/ +#if defined(CONFIG_IRDA) || defined(CONFIG_IRDA_MODULE) static struct pxaficp_platform_data palmtc_ficp_platform_data = { .gpio_pwdown = GPIO_NR_PALMTC_IR_DISABLE, .transceiver_cap = IR_SIRMODE | IR_OFF, }; +static void __init palmtc_irda_init(void) +{ + pxa_set_ficp_info(&palmtc_ficp_platform_data); +} +#else +static inline void palmtc_irda_init(void) {} +#endif + /****************************************************************************** * Keyboard ******************************************************************************/ +#if defined(CONFIG_KEYBOARD_MATRIX) || defined(CONFIG_KEYBOARD_MATRIX_MODULE) static const uint32_t palmtc_matrix_keys[] = { KEY(0, 0, KEY_F1), KEY(0, 1, KEY_X), @@ -290,27 +328,103 @@ static struct platform_device palmtc_keyboard = { .platform_data = &palmtc_keypad_platform_data, }, }; +static void __init palmtc_mkp_init(void) +{ + platform_device_register(&palmtc_keyboard); +} +#else +static inline void palmtc_mkp_init(void) {} +#endif /****************************************************************************** * UDC ******************************************************************************/ -static struct pxa2xx_udc_mach_info palmtc_udc_info __initdata = { +#if defined(CONFIG_USB_GADGET_PXA25X)||defined(CONFIG_USB_GADGET_PXA25X_MODULE) +static struct gpio_vbus_mach_info palmtc_udc_info = { .gpio_vbus = GPIO_NR_PALMTC_USB_DETECT_N, .gpio_vbus_inverted = 1, .gpio_pullup = GPIO_NR_PALMTC_USB_POWER, }; +static struct platform_device palmtc_gpio_vbus = { + .name = "gpio-vbus", + .id = -1, + .dev = { + .platform_data = &palmtc_udc_info, + }, +}; + +static void __init palmtc_udc_init(void) +{ + platform_device_register(&palmtc_gpio_vbus); +}; +#else +static inline void palmtc_udc_init(void) {} +#endif + /****************************************************************************** * Touchscreen / Battery / GPIO-extender ******************************************************************************/ -static struct platform_device palmtc_ucb1400_core = { +#if defined(CONFIG_TOUCHSCREEN_UCB1400) || \ + defined(CONFIG_TOUCHSCREEN_UCB1400_MODULE) +static struct platform_device palmtc_ucb1400_device = { .name = "ucb1400_core", .id = -1, }; +static void __init palmtc_ts_init(void) +{ + pxa_set_ac97_info(NULL); + platform_device_register(&palmtc_ucb1400_device); +} +#else +static inline void palmtc_ts_init(void) {} +#endif + +/****************************************************************************** + * LEDs + ******************************************************************************/ +#if defined(CONFIG_LEDS_GPIO) || defined(CONFIG_LEDS_GPIO_MODULE) +struct gpio_led palmtc_gpio_leds[] = { +{ + .name = "palmtc:green:user", + .default_trigger = "none", + .gpio = GPIO_NR_PALMTC_LED_POWER, + .active_low = 1, +}, { + .name = "palmtc:vibra:vibra", + .default_trigger = "none", + .gpio = GPIO_NR_PALMTC_VIBRA_POWER, + .active_low = 1, +} + +}; + +static struct gpio_led_platform_data palmtc_gpio_led_info = { + .leds = palmtc_gpio_leds, + .num_leds = ARRAY_SIZE(palmtc_gpio_leds), +}; + +static struct platform_device palmtc_leds = { + .name = "leds-gpio", + .id = -1, + .dev = { + .platform_data = &palmtc_gpio_led_info, + } +}; + +static void __init palmtc_leds_init(void) +{ + platform_device_register(&palmtc_leds); +} +#else +static inline void palmtc_leds_init(void) {} +#endif + /****************************************************************************** * NOR Flash ******************************************************************************/ +#if defined(CONFIG_MTD_PHYSMAP) || defined(CONFIG_MTD_PHYSMAP_MODULE) static struct resource palmtc_flash_resource = { .start = PXA_CS0_PHYS, .end = PXA_CS0_PHYS + SZ_16M - 1, @@ -356,24 +470,33 @@ static struct platform_device palmtc_flash = { }, }; +static void __init palmtc_nor_init(void) +{ + platform_device_register(&palmtc_flash); +} +#else +static inline void palmtc_nor_init(void) {} +#endif + /****************************************************************************** * Framebuffer ******************************************************************************/ +#if defined(CONFIG_FB_PXA) || defined(CONFIG_FB_PXA_MODULE) static struct pxafb_mode_info palmtc_lcd_modes[] = { -{ - .pixclock = 115384, - .xres = 320, - .yres = 320, - .bpp = 16, - - .left_margin = 27, - .right_margin = 7, - .upper_margin = 7, - .lower_margin = 8, - - .hsync_len = 6, - .vsync_len = 1, -}, + { + .pixclock = 115384, + .xres = 320, + .yres = 320, + .bpp = 16, + + .left_margin = 27, + .right_margin = 7, + .upper_margin = 7, + .lower_margin = 8, + + .hsync_len = 6, + .vsync_len = 1, + }, }; static struct pxafb_mach_info palmtc_lcd_screen = { @@ -382,17 +505,17 @@ static struct pxafb_mach_info palmtc_lcd_screen = { .lcd_conn = LCD_COLOR_TFT_16BPP | LCD_PCLK_EDGE_FALL, }; +static void __init palmtc_lcd_init(void) +{ + set_pxa_fb_info(&palmtc_lcd_screen); +} +#else +static inline void palmtc_lcd_init(void) {} +#endif + /****************************************************************************** * Machine init ******************************************************************************/ -static struct platform_device *devices[] __initdata = { - &palmtc_backlight, - &palmtc_ucb1400_core, - &palmtc_keyboard, - &palmtc_pxa_keys, - &palmtc_flash, -}; - static void __init palmtc_init(void) { pxa2xx_mfp_config(ARRAY_AND_SIZE(palmtc_pin_config)); @@ -402,18 +525,21 @@ static void __init palmtc_init(void) pxa_set_stuart_info(NULL); pxa_set_hwuart_info(NULL); - set_pxa_fb_info(&palmtc_lcd_screen); - pxa_set_mci_info(&palmtc_mci_platform_data); - pxa_set_udc_info(&palmtc_udc_info); - pxa_set_ac97_info(NULL); - pxa_set_ficp_info(&palmtc_ficp_platform_data); - - platform_add_devices(devices, ARRAY_SIZE(devices)); + palmtc_mmc_init(); + palmtc_keys_init(); + palmtc_pwm_init(); + palmtc_irda_init(); + palmtc_mkp_init(); + palmtc_udc_init(); + palmtc_ts_init(); + palmtc_nor_init(); + palmtc_lcd_init(); + palmtc_leds_init(); }; MACHINE_START(PALMTC, "Palm Tungsten|C") .boot_params = 0xa0000100, - .map_io = pxa_map_io, + .map_io = pxa25x_map_io, .init_irq = pxa25x_init_irq, .timer = &pxa_timer, .init_machine = palmtc_init diff --git a/arch/arm/mach-pxa/palmte2.c b/arch/arm/mach-pxa/palmte2.c index a9dae7b..3f25014 100644 --- a/arch/arm/mach-pxa/palmte2.c +++ b/arch/arm/mach-pxa/palmte2.c @@ -374,7 +374,7 @@ static void __init palmte2_init(void) MACHINE_START(PALMTE2, "Palm Tungsten|E2") .boot_params = 0xa0000100, - .map_io = pxa_map_io, + .map_io = pxa25x_map_io, .init_irq = pxa25x_init_irq, .timer = &pxa_timer, .init_machine = palmte2_init diff --git a/arch/arm/mach-pxa/palmtreo.c b/arch/arm/mach-pxa/palmtreo.c index 00e2d7b..8aadad5 100644 --- a/arch/arm/mach-pxa/palmtreo.c +++ b/arch/arm/mach-pxa/palmtreo.c @@ -442,7 +442,7 @@ static void __init centro_init(void) MACHINE_START(TREO680, "Palm Treo 680") .boot_params = 0xa0000100, - .map_io = pxa_map_io, + .map_io = pxa27x_map_io, .reserve = treo_reserve, .init_irq = pxa27x_init_irq, .timer = &pxa_timer, @@ -451,7 +451,7 @@ MACHINE_END MACHINE_START(CENTRO, "Palm Centro 685") .boot_params = 0xa0000100, - .map_io = pxa_map_io, + .map_io = pxa27x_map_io, .reserve = treo_reserve, .init_irq = pxa27x_init_irq, .timer = &pxa_timer, diff --git a/arch/arm/mach-pxa/palmtx.c b/arch/arm/mach-pxa/palmtx.c index e5c9932..595f002 100644 --- a/arch/arm/mach-pxa/palmtx.c +++ b/arch/arm/mach-pxa/palmtx.c @@ -334,7 +334,7 @@ static struct map_desc palmtx_io_desc[] __initdata = { static void __init palmtx_map_io(void) { - pxa_map_io(); + pxa27x_map_io(); iotable_init(palmtx_io_desc, ARRAY_SIZE(palmtx_io_desc)); } diff --git a/arch/arm/mach-pxa/palmz72.c b/arch/arm/mach-pxa/palmz72.c index af6203f..7bf4017 100644 --- a/arch/arm/mach-pxa/palmz72.c +++ b/arch/arm/mach-pxa/palmz72.c @@ -280,7 +280,7 @@ static void __init palmz72_init(void) MACHINE_START(PALMZ72, "Palm Zire72") .boot_params = 0xa0000100, - .map_io = pxa_map_io, + .map_io = pxa27x_map_io, .init_irq = pxa27x_init_irq, .timer = &pxa_timer, .init_machine = palmz72_init diff --git a/arch/arm/mach-pxa/pcm027.c b/arch/arm/mach-pxa/pcm027.c index c77e8f3..1fc8a66 100644 --- a/arch/arm/mach-pxa/pcm027.c +++ b/arch/arm/mach-pxa/pcm027.c @@ -25,12 +25,12 @@ #include <linux/mtd/physmap.h> #include <linux/spi/spi.h> #include <linux/spi/max7301.h> +#include <linux/spi/pxa2xx_spi.h> #include <linux/leds.h> #include <asm/mach-types.h> #include <asm/mach/arch.h> #include <mach/pxa27x.h> -#include <mach/pxa2xx_spi.h> #include <mach/pcm027.h> #include "generic.h" @@ -244,7 +244,7 @@ static void __init pcm027_init(void) static void __init pcm027_map_io(void) { - pxa_map_io(); + pxa27x_map_io(); /* initialize sleep mode regs (wake-up sources, etc) */ PGSR0 = 0x01308000; diff --git a/arch/arm/mach-pxa/poodle.c b/arch/arm/mach-pxa/poodle.c index 93a191c..4f0ff1a 100644 --- a/arch/arm/mach-pxa/poodle.c +++ b/arch/arm/mach-pxa/poodle.c @@ -25,6 +25,7 @@ #include <linux/i2c.h> #include <linux/spi/spi.h> #include <linux/spi/ads7846.h> +#include <linux/spi/pxa2xx_spi.h> #include <linux/mtd/sharpsl.h> #include <mach/hardware.h> @@ -43,7 +44,6 @@ #include <mach/irda.h> #include <mach/poodle.h> #include <mach/pxafb.h> -#include <mach/pxa2xx_spi.h> #include <plat/i2c.h> #include <asm/hardware/scoop.h> @@ -466,7 +466,7 @@ static void __init fixup_poodle(struct machine_desc *desc, MACHINE_START(POODLE, "SHARP Poodle") .fixup = fixup_poodle, - .map_io = pxa_map_io, + .map_io = pxa25x_map_io, .nr_irqs = POODLE_NR_IRQS, /* 4 for LoCoMo */ .init_irq = pxa25x_init_irq, .timer = &pxa_timer, diff --git a/arch/arm/mach-pxa/pxa25x.c b/arch/arm/mach-pxa/pxa25x.c index de53f2e..3f5241c 100644 --- a/arch/arm/mach-pxa/pxa25x.c +++ b/arch/arm/mach-pxa/pxa25x.c @@ -23,6 +23,7 @@ #include <linux/suspend.h> #include <linux/sysdev.h> +#include <asm/mach/map.h> #include <mach/hardware.h> #include <mach/irqs.h> #include <mach/gpio.h> @@ -30,6 +31,7 @@ #include <mach/reset.h> #include <mach/pm.h> #include <mach/dma.h> +#include <mach/smemc.h> #include "generic.h" #include "devices.h" @@ -90,23 +92,21 @@ unsigned int pxa25x_get_clk_frequency_khz(int info) return (turbo & 1) ? (N/1000) : (M/1000); } -/* - * Return the current memory clock frequency in units of 10kHz - */ -unsigned int pxa25x_get_memclk_frequency_10khz(void) +static unsigned long clk_pxa25x_mem_getrate(struct clk *clk) { - return L_clk_mult[(CCCR >> 0) & 0x1f] * BASE_CLK / 10000; + return L_clk_mult[(CCCR >> 0) & 0x1f] * BASE_CLK; } -static unsigned long clk_pxa25x_lcd_getrate(struct clk *clk) -{ - return pxa25x_get_memclk_frequency_10khz() * 10000; -} +static const struct clkops clk_pxa25x_mem_ops = { + .enable = clk_dummy_enable, + .disable = clk_dummy_disable, + .getrate = clk_pxa25x_mem_getrate, +}; static const struct clkops clk_pxa25x_lcd_ops = { - .enable = clk_cken_enable, - .disable = clk_cken_disable, - .getrate = clk_pxa25x_lcd_getrate, + .enable = clk_pxa2xx_cken_enable, + .disable = clk_pxa2xx_cken_disable, + .getrate = clk_pxa25x_mem_getrate, }; static unsigned long gpio12_config_32k[] = { @@ -160,31 +160,30 @@ static const struct clkops clk_pxa25x_gpio11_ops = { * 95.842MHz -> MMC 19.169MHz, I2C 31.949MHz, FICP 47.923MHz, USB 47.923MHz * 147.456MHz -> UART 14.7456MHz, AC97 12.288MHz, I2S 5.672MHz (allegedly) */ -static DEFINE_CKEN(pxa25x_hwuart, HWUART, 14745600, 1); - -static struct clk_lookup pxa25x_hwuart_clkreg = - INIT_CLKREG(&clk_pxa25x_hwuart, "pxa2xx-uart.3", NULL); /* * PXA 2xx clock declarations. */ +static DEFINE_PXA2_CKEN(pxa25x_hwuart, HWUART, 14745600, 1); +static DEFINE_PXA2_CKEN(pxa25x_ffuart, FFUART, 14745600, 1); +static DEFINE_PXA2_CKEN(pxa25x_btuart, BTUART, 14745600, 1); +static DEFINE_PXA2_CKEN(pxa25x_stuart, STUART, 14745600, 1); +static DEFINE_PXA2_CKEN(pxa25x_usb, USB, 47923000, 5); +static DEFINE_PXA2_CKEN(pxa25x_mmc, MMC, 19169000, 0); +static DEFINE_PXA2_CKEN(pxa25x_i2c, I2C, 31949000, 0); +static DEFINE_PXA2_CKEN(pxa25x_ssp, SSP, 3686400, 0); +static DEFINE_PXA2_CKEN(pxa25x_nssp, NSSP, 3686400, 0); +static DEFINE_PXA2_CKEN(pxa25x_assp, ASSP, 3686400, 0); +static DEFINE_PXA2_CKEN(pxa25x_pwm0, PWM0, 3686400, 0); +static DEFINE_PXA2_CKEN(pxa25x_pwm1, PWM1, 3686400, 0); +static DEFINE_PXA2_CKEN(pxa25x_ac97, AC97, 24576000, 0); +static DEFINE_PXA2_CKEN(pxa25x_i2s, I2S, 14745600, 0); +static DEFINE_PXA2_CKEN(pxa25x_ficp, FICP, 47923000, 0); + static DEFINE_CK(pxa25x_lcd, LCD, &clk_pxa25x_lcd_ops); -static DEFINE_CKEN(pxa25x_ffuart, FFUART, 14745600, 1); -static DEFINE_CKEN(pxa25x_btuart, BTUART, 14745600, 1); -static DEFINE_CKEN(pxa25x_stuart, STUART, 14745600, 1); -static DEFINE_CKEN(pxa25x_usb, USB, 47923000, 5); static DEFINE_CLK(pxa25x_gpio11, &clk_pxa25x_gpio11_ops, 3686400, 0); static DEFINE_CLK(pxa25x_gpio12, &clk_pxa25x_gpio12_ops, 32768, 0); -static DEFINE_CKEN(pxa25x_mmc, MMC, 19169000, 0); -static DEFINE_CKEN(pxa25x_i2c, I2C, 31949000, 0); -static DEFINE_CKEN(pxa25x_ssp, SSP, 3686400, 0); -static DEFINE_CKEN(pxa25x_nssp, NSSP, 3686400, 0); -static DEFINE_CKEN(pxa25x_assp, ASSP, 3686400, 0); -static DEFINE_CKEN(pxa25x_pwm0, PWM0, 3686400, 0); -static DEFINE_CKEN(pxa25x_pwm1, PWM1, 3686400, 0); -static DEFINE_CKEN(pxa25x_ac97, AC97, 24576000, 0); -static DEFINE_CKEN(pxa25x_i2s, I2S, 14745600, 0); -static DEFINE_CKEN(pxa25x_ficp, FICP, 47923000, 0); +static DEFINE_CLK(pxa25x_mem, &clk_pxa25x_mem_ops, 0, 0); static struct clk_lookup pxa25x_clkregs[] = { INIT_CLKREG(&clk_pxa25x_lcd, "pxa2xx-fb", NULL), @@ -205,8 +204,12 @@ static struct clk_lookup pxa25x_clkregs[] = { INIT_CLKREG(&clk_pxa25x_ac97, NULL, "AC97CLK"), INIT_CLKREG(&clk_pxa25x_gpio11, NULL, "GPIO11_CLK"), INIT_CLKREG(&clk_pxa25x_gpio12, NULL, "GPIO12_CLK"), + INIT_CLKREG(&clk_pxa25x_mem, "pxa2xx-pcmcia", NULL), }; +static struct clk_lookup pxa25x_hwuart_clkreg = + INIT_CLKREG(&clk_pxa25x_hwuart, "pxa2xx-uart.3", NULL); + #ifdef CONFIG_PM #define SAVE(x) sleep_save[SLEEP_SAVE_##x] = x @@ -219,20 +222,17 @@ static struct clk_lookup pxa25x_clkregs[] = { */ enum { SLEEP_SAVE_PSTR, - SLEEP_SAVE_CKEN, SLEEP_SAVE_COUNT }; static void pxa25x_cpu_pm_save(unsigned long *sleep_save) { - SAVE(CKEN); SAVE(PSTR); } static void pxa25x_cpu_pm_restore(unsigned long *sleep_save) { - RESTORE(CKEN); RESTORE(PSTR); } @@ -320,6 +320,22 @@ void __init pxa26x_init_irq(void) } #endif +static struct map_desc pxa25x_io_desc[] __initdata = { + { /* Mem Ctl */ + .virtual = SMEMC_VIRT, + .pfn = __phys_to_pfn(PXA2XX_SMEMC_BASE), + .length = 0x00200000, + .type = MT_DEVICE + }, +}; + +void __init pxa25x_map_io(void) +{ + pxa_map_io(); + iotable_init(ARRAY_AND_SIZE(pxa25x_io_desc)); + pxa25x_get_clk_frequency_khz(1); +} + static struct platform_device *pxa25x_devices[] __initdata = { &pxa25x_device_udc, &pxa_device_pmu, @@ -339,7 +355,9 @@ static struct sys_device pxa25x_sysdev[] = { .cls = &pxa2xx_mfp_sysclass, }, { .cls = &pxa_gpio_sysclass, - }, + }, { + .cls = &pxa2xx_clock_sysclass, + } }; static int __init pxa25x_init(void) diff --git a/arch/arm/mach-pxa/pxa27x.c b/arch/arm/mach-pxa/pxa27x.c index d1fbf29..b2130b7 100644 --- a/arch/arm/mach-pxa/pxa27x.c +++ b/arch/arm/mach-pxa/pxa27x.c @@ -17,7 +17,9 @@ #include <linux/suspend.h> #include <linux/platform_device.h> #include <linux/sysdev.h> +#include <linux/io.h> +#include <asm/mach/map.h> #include <mach/hardware.h> #include <asm/irq.h> #include <mach/irqs.h> @@ -27,6 +29,8 @@ #include <mach/ohci.h> #include <mach/pm.h> #include <mach/dma.h> +#include <mach/smemc.h> + #include <plat/i2c.h> #include "generic.h" @@ -107,10 +111,9 @@ unsigned int pxa27x_get_clk_frequency_khz(int info) } /* - * Return the current mem clock frequency in units of 10kHz as - * reflected by CCCR[A], B, and L + * Return the current mem clock frequency as reflected by CCCR[A], B, and L */ -unsigned int pxa27x_get_memclk_frequency_10khz(void) +static unsigned long clk_pxa27x_mem_getrate(struct clk *clk) { unsigned long ccsr, clkcfg; unsigned int l, L, m, M; @@ -129,9 +132,15 @@ unsigned int pxa27x_get_memclk_frequency_10khz(void) L = l * BASE_CLK; M = (!cccr_a) ? (L/m) : ((b) ? L : (L/2)); - return (M / 10000); + return M; } +static const struct clkops clk_pxa27x_mem_ops = { + .enable = clk_dummy_enable, + .disable = clk_dummy_disable, + .getrate = clk_pxa27x_mem_getrate, +}; + /* * Return the current LCD clock frequency in units of 10kHz as */ @@ -157,36 +166,38 @@ static unsigned long clk_pxa27x_lcd_getrate(struct clk *clk) } static const struct clkops clk_pxa27x_lcd_ops = { - .enable = clk_cken_enable, - .disable = clk_cken_disable, + .enable = clk_pxa2xx_cken_enable, + .disable = clk_pxa2xx_cken_disable, .getrate = clk_pxa27x_lcd_getrate, }; +static DEFINE_PXA2_CKEN(pxa27x_ffuart, FFUART, 14857000, 1); +static DEFINE_PXA2_CKEN(pxa27x_btuart, BTUART, 14857000, 1); +static DEFINE_PXA2_CKEN(pxa27x_stuart, STUART, 14857000, 1); +static DEFINE_PXA2_CKEN(pxa27x_i2s, I2S, 14682000, 0); +static DEFINE_PXA2_CKEN(pxa27x_i2c, I2C, 32842000, 0); +static DEFINE_PXA2_CKEN(pxa27x_usb, USB, 48000000, 5); +static DEFINE_PXA2_CKEN(pxa27x_mmc, MMC, 19500000, 0); +static DEFINE_PXA2_CKEN(pxa27x_ficp, FICP, 48000000, 0); +static DEFINE_PXA2_CKEN(pxa27x_usbhost, USBHOST, 48000000, 0); +static DEFINE_PXA2_CKEN(pxa27x_pwri2c, PWRI2C, 13000000, 0); +static DEFINE_PXA2_CKEN(pxa27x_keypad, KEYPAD, 32768, 0); +static DEFINE_PXA2_CKEN(pxa27x_ssp1, SSP1, 13000000, 0); +static DEFINE_PXA2_CKEN(pxa27x_ssp2, SSP2, 13000000, 0); +static DEFINE_PXA2_CKEN(pxa27x_ssp3, SSP3, 13000000, 0); +static DEFINE_PXA2_CKEN(pxa27x_pwm0, PWM0, 13000000, 0); +static DEFINE_PXA2_CKEN(pxa27x_pwm1, PWM1, 13000000, 0); +static DEFINE_PXA2_CKEN(pxa27x_ac97, AC97, 24576000, 0); +static DEFINE_PXA2_CKEN(pxa27x_ac97conf, AC97CONF, 24576000, 0); +static DEFINE_PXA2_CKEN(pxa27x_msl, MSL, 48000000, 0); +static DEFINE_PXA2_CKEN(pxa27x_usim, USIM, 48000000, 0); +static DEFINE_PXA2_CKEN(pxa27x_memstk, MEMSTK, 19500000, 0); +static DEFINE_PXA2_CKEN(pxa27x_im, IM, 0, 0); +static DEFINE_PXA2_CKEN(pxa27x_memc, MEMC, 0, 0); + static DEFINE_CK(pxa27x_lcd, LCD, &clk_pxa27x_lcd_ops); static DEFINE_CK(pxa27x_camera, CAMERA, &clk_pxa27x_lcd_ops); -static DEFINE_CKEN(pxa27x_ffuart, FFUART, 14857000, 1); -static DEFINE_CKEN(pxa27x_btuart, BTUART, 14857000, 1); -static DEFINE_CKEN(pxa27x_stuart, STUART, 14857000, 1); -static DEFINE_CKEN(pxa27x_i2s, I2S, 14682000, 0); -static DEFINE_CKEN(pxa27x_i2c, I2C, 32842000, 0); -static DEFINE_CKEN(pxa27x_usb, USB, 48000000, 5); -static DEFINE_CKEN(pxa27x_mmc, MMC, 19500000, 0); -static DEFINE_CKEN(pxa27x_ficp, FICP, 48000000, 0); -static DEFINE_CKEN(pxa27x_usbhost, USBHOST, 48000000, 0); -static DEFINE_CKEN(pxa27x_pwri2c, PWRI2C, 13000000, 0); -static DEFINE_CKEN(pxa27x_keypad, KEYPAD, 32768, 0); -static DEFINE_CKEN(pxa27x_ssp1, SSP1, 13000000, 0); -static DEFINE_CKEN(pxa27x_ssp2, SSP2, 13000000, 0); -static DEFINE_CKEN(pxa27x_ssp3, SSP3, 13000000, 0); -static DEFINE_CKEN(pxa27x_pwm0, PWM0, 13000000, 0); -static DEFINE_CKEN(pxa27x_pwm1, PWM1, 13000000, 0); -static DEFINE_CKEN(pxa27x_ac97, AC97, 24576000, 0); -static DEFINE_CKEN(pxa27x_ac97conf, AC97CONF, 24576000, 0); -static DEFINE_CKEN(pxa27x_msl, MSL, 48000000, 0); -static DEFINE_CKEN(pxa27x_usim, USIM, 48000000, 0); -static DEFINE_CKEN(pxa27x_memstk, MEMSTK, 19500000, 0); -static DEFINE_CKEN(pxa27x_im, IM, 0, 0); -static DEFINE_CKEN(pxa27x_memc, MEMC, 0, 0); +static DEFINE_CLK(pxa27x_mem, &clk_pxa27x_mem_ops, 0, 0); static struct clk_lookup pxa27x_clkregs[] = { INIT_CLKREG(&clk_pxa27x_lcd, "pxa2xx-fb", NULL), @@ -215,6 +226,7 @@ static struct clk_lookup pxa27x_clkregs[] = { INIT_CLKREG(&clk_pxa27x_memstk, NULL, "MSTKCLK"), INIT_CLKREG(&clk_pxa27x_im, NULL, "IMCLK"), INIT_CLKREG(&clk_pxa27x_memc, NULL, "MEMCLK"), + INIT_CLKREG(&clk_pxa27x_mem, "pxa2xx-pcmcia", NULL), }; #ifdef CONFIG_PM @@ -246,7 +258,6 @@ int __init pxa27x_set_pwrmode(unsigned int mode) */ enum { SLEEP_SAVE_PSTR, - SLEEP_SAVE_CKEN, SLEEP_SAVE_MDREFR, SLEEP_SAVE_PCFR, SLEEP_SAVE_COUNT @@ -254,21 +265,19 @@ enum { void pxa27x_cpu_pm_save(unsigned long *sleep_save) { - SAVE(MDREFR); + sleep_save[SLEEP_SAVE_MDREFR] = __raw_readl(MDREFR); SAVE(PCFR); - SAVE(CKEN); SAVE(PSTR); } void pxa27x_cpu_pm_restore(unsigned long *sleep_save) { - RESTORE(MDREFR); + __raw_writel(sleep_save[SLEEP_SAVE_MDREFR], MDREFR); RESTORE(PCFR); PSSR = PSSR_RDH | PSSR_PH; - RESTORE(CKEN); RESTORE(PSTR); } @@ -370,6 +379,27 @@ void __init pxa27x_init_irq(void) pxa_init_gpio(IRQ_GPIO_2_x, 2, 120, pxa27x_set_wake); } +static struct map_desc pxa27x_io_desc[] __initdata = { + { /* Mem Ctl */ + .virtual = SMEMC_VIRT, + .pfn = __phys_to_pfn(PXA2XX_SMEMC_BASE), + .length = 0x00200000, + .type = MT_DEVICE + }, { /* IMem ctl */ + .virtual = 0xfe000000, + .pfn = __phys_to_pfn(0x58000000), + .length = 0x00100000, + .type = MT_DEVICE + }, +}; + +void __init pxa27x_map_io(void) +{ + pxa_map_io(); + iotable_init(ARRAY_AND_SIZE(pxa27x_io_desc)); + pxa27x_get_clk_frequency_khz(1); +} + /* * device registration specific to PXA27x. */ @@ -405,7 +435,9 @@ static struct sys_device pxa27x_sysdev[] = { .cls = &pxa2xx_mfp_sysclass, }, { .cls = &pxa_gpio_sysclass, - }, + }, { + .cls = &pxa2xx_clock_sysclass, + } }; static int __init pxa27x_init(void) diff --git a/arch/arm/mach-pxa/pxa3xx.c b/arch/arm/mach-pxa/pxa3xx.c index d1c747c..e14818f 100644 --- a/arch/arm/mach-pxa/pxa3xx.c +++ b/arch/arm/mach-pxa/pxa3xx.c @@ -22,6 +22,7 @@ #include <linux/io.h> #include <linux/sysdev.h> +#include <asm/mach/map.h> #include <mach/hardware.h> #include <mach/gpio.h> #include <mach/pxa3xx-regs.h> @@ -30,193 +31,16 @@ #include <mach/pm.h> #include <mach/dma.h> #include <mach/regs-intc.h> +#include <mach/smemc.h> #include <plat/i2c.h> #include "generic.h" #include "devices.h" #include "clock.h" -/* Crystal clock: 13MHz */ -#define BASE_CLK 13000000 - -/* Ring Oscillator Clock: 60MHz */ -#define RO_CLK 60000000 - -#define ACCR_D0CS (1 << 26) -#define ACCR_PCCE (1 << 11) - #define PECR_IE(n) ((1 << ((n) * 2)) << 28) #define PECR_IS(n) ((1 << ((n) * 2)) << 29) -/* crystal frequency to static memory controller multiplier (SMCFS) */ -static unsigned char smcfs_mult[8] = { 6, 0, 8, 0, 0, 16, }; - -/* crystal frequency to HSIO bus frequency multiplier (HSS) */ -static unsigned char hss_mult[4] = { 8, 12, 16, 24 }; - -/* - * Get the clock frequency as reflected by CCSR and the turbo flag. - * We assume these values have been applied via a fcs. - * If info is not 0 we also display the current settings. - */ -unsigned int pxa3xx_get_clk_frequency_khz(int info) -{ - unsigned long acsr, xclkcfg; - unsigned int t, xl, xn, hss, ro, XL, XN, CLK, HSS; - - /* Read XCLKCFG register turbo bit */ - __asm__ __volatile__("mrc\tp14, 0, %0, c6, c0, 0" : "=r"(xclkcfg)); - t = xclkcfg & 0x1; - - acsr = ACSR; - - xl = acsr & 0x1f; - xn = (acsr >> 8) & 0x7; - hss = (acsr >> 14) & 0x3; - - XL = xl * BASE_CLK; - XN = xn * XL; - - ro = acsr & ACCR_D0CS; - - CLK = (ro) ? RO_CLK : ((t) ? XN : XL); - HSS = (ro) ? RO_CLK : hss_mult[hss] * BASE_CLK; - - if (info) { - pr_info("RO Mode clock: %d.%02dMHz (%sactive)\n", - RO_CLK / 1000000, (RO_CLK % 1000000) / 10000, - (ro) ? "" : "in"); - pr_info("Run Mode clock: %d.%02dMHz (*%d)\n", - XL / 1000000, (XL % 1000000) / 10000, xl); - pr_info("Turbo Mode clock: %d.%02dMHz (*%d, %sactive)\n", - XN / 1000000, (XN % 1000000) / 10000, xn, - (t) ? "" : "in"); - pr_info("HSIO bus clock: %d.%02dMHz\n", - HSS / 1000000, (HSS % 1000000) / 10000); - } - - return CLK / 1000; -} - -void pxa3xx_clear_reset_status(unsigned int mask) -{ - /* RESET_STATUS_* has a 1:1 mapping with ARSR */ - ARSR = mask; -} - -/* - * Return the current AC97 clock frequency. - */ -static unsigned long clk_pxa3xx_ac97_getrate(struct clk *clk) -{ - unsigned long rate = 312000000; - unsigned long ac97_div; - - ac97_div = AC97_DIV; - - /* This may loose precision for some rates but won't for the - * standard 24.576MHz. - */ - rate /= (ac97_div >> 12) & 0x7fff; - rate *= (ac97_div & 0xfff); - - return rate; -} - -/* - * Return the current HSIO bus clock frequency - */ -static unsigned long clk_pxa3xx_hsio_getrate(struct clk *clk) -{ - unsigned long acsr; - unsigned int hss, hsio_clk; - - acsr = ACSR; - - hss = (acsr >> 14) & 0x3; - hsio_clk = (acsr & ACCR_D0CS) ? RO_CLK : hss_mult[hss] * BASE_CLK; - - return hsio_clk; -} - -void clk_pxa3xx_cken_enable(struct clk *clk) -{ - unsigned long mask = 1ul << (clk->cken & 0x1f); - - if (clk->cken < 32) - CKENA |= mask; - else - CKENB |= mask; -} - -void clk_pxa3xx_cken_disable(struct clk *clk) -{ - unsigned long mask = 1ul << (clk->cken & 0x1f); - - if (clk->cken < 32) - CKENA &= ~mask; - else - CKENB &= ~mask; -} - -const struct clkops clk_pxa3xx_cken_ops = { - .enable = clk_pxa3xx_cken_enable, - .disable = clk_pxa3xx_cken_disable, -}; - -static const struct clkops clk_pxa3xx_hsio_ops = { - .enable = clk_pxa3xx_cken_enable, - .disable = clk_pxa3xx_cken_disable, - .getrate = clk_pxa3xx_hsio_getrate, -}; - -static const struct clkops clk_pxa3xx_ac97_ops = { - .enable = clk_pxa3xx_cken_enable, - .disable = clk_pxa3xx_cken_disable, - .getrate = clk_pxa3xx_ac97_getrate, -}; - -static void clk_pout_enable(struct clk *clk) -{ - OSCC |= OSCC_PEN; -} - -static void clk_pout_disable(struct clk *clk) -{ - OSCC &= ~OSCC_PEN; -} - -static const struct clkops clk_pout_ops = { - .enable = clk_pout_enable, - .disable = clk_pout_disable, -}; - -static void clk_dummy_enable(struct clk *clk) -{ -} - -static void clk_dummy_disable(struct clk *clk) -{ -} - -static const struct clkops clk_dummy_ops = { - .enable = clk_dummy_enable, - .disable = clk_dummy_disable, -}; - -static struct clk clk_pxa3xx_pout = { - .ops = &clk_pout_ops, - .rate = 13000000, - .delay = 70, -}; - -static struct clk clk_dummy = { - .ops = &clk_dummy_ops, -}; - -static DEFINE_PXA3_CK(pxa3xx_lcd, LCD, &clk_pxa3xx_hsio_ops); -static DEFINE_PXA3_CK(pxa3xx_camera, CAMERA, &clk_pxa3xx_hsio_ops); -static DEFINE_PXA3_CK(pxa3xx_ac97, AC97, &clk_pxa3xx_ac97_ops); static DEFINE_PXA3_CKEN(pxa3xx_ffuart, FFUART, 14857000, 1); static DEFINE_PXA3_CKEN(pxa3xx_btuart, BTUART, 14857000, 1); static DEFINE_PXA3_CKEN(pxa3xx_stuart, STUART, 14857000, 1); @@ -234,6 +58,12 @@ static DEFINE_PXA3_CKEN(pxa3xx_pwm1, PWM1, 13000000, 0); static DEFINE_PXA3_CKEN(pxa3xx_mmc1, MMC1, 19500000, 0); static DEFINE_PXA3_CKEN(pxa3xx_mmc2, MMC2, 19500000, 0); +static DEFINE_CK(pxa3xx_lcd, LCD, &clk_pxa3xx_hsio_ops); +static DEFINE_CK(pxa3xx_smemc, SMC, &clk_pxa3xx_smemc_ops); +static DEFINE_CK(pxa3xx_camera, CAMERA, &clk_pxa3xx_hsio_ops); +static DEFINE_CK(pxa3xx_ac97, AC97, &clk_pxa3xx_ac97_ops); +static DEFINE_CLK(pxa3xx_pout, &clk_pxa3xx_pout_ops, 13000000, 70); + static struct clk_lookup pxa3xx_clkregs[] = { INIT_CLKREG(&clk_pxa3xx_pout, NULL, "CLK_POUT"), /* Power I2C clock is always on */ @@ -258,6 +88,7 @@ static struct clk_lookup pxa3xx_clkregs[] = { INIT_CLKREG(&clk_pxa3xx_pwm1, "pxa27x-pwm.1", NULL), INIT_CLKREG(&clk_pxa3xx_mmc1, "pxa2xx-mci.0", NULL), INIT_CLKREG(&clk_pxa3xx_mmc2, "pxa2xx-mci.1", NULL), + INIT_CLKREG(&clk_pxa3xx_smemc, "pxa2xx-pcmcia", NULL), }; #ifdef CONFIG_PM @@ -268,30 +99,6 @@ static struct clk_lookup pxa3xx_clkregs[] = { static void __iomem *sram; static unsigned long wakeup_src; -#define SAVE(x) sleep_save[SLEEP_SAVE_##x] = x -#define RESTORE(x) x = sleep_save[SLEEP_SAVE_##x] - -enum { SLEEP_SAVE_CKENA, - SLEEP_SAVE_CKENB, - SLEEP_SAVE_ACCR, - - SLEEP_SAVE_COUNT, -}; - -static void pxa3xx_cpu_pm_save(unsigned long *sleep_save) -{ - SAVE(CKENA); - SAVE(CKENB); - SAVE(ACCR); -} - -static void pxa3xx_cpu_pm_restore(unsigned long *sleep_save) -{ - RESTORE(ACCR); - RESTORE(CKENA); - RESTORE(CKENB); -} - /* * Enter a standby mode (S0D1C2 or S0D2C2). Upon wakeup, the dynamic * memory controller has to be reinitialised, so we place some code @@ -390,9 +197,6 @@ static int pxa3xx_cpu_pm_valid(suspend_state_t state) } static struct pxa_cpu_pm_fns pxa3xx_cpu_pm_fns = { - .save_count = SLEEP_SAVE_COUNT, - .save = pxa3xx_cpu_pm_save, - .restore = pxa3xx_cpu_pm_restore, .valid = pxa3xx_cpu_pm_valid, .enter = pxa3xx_cpu_pm_enter, }; @@ -580,6 +384,22 @@ void __init pxa3xx_init_irq(void) pxa_init_gpio(IRQ_GPIO_2_x, 2, 127, NULL); } +static struct map_desc pxa3xx_io_desc[] __initdata = { + { /* Mem Ctl */ + .virtual = SMEMC_VIRT, + .pfn = __phys_to_pfn(PXA3XX_SMEMC_BASE), + .length = 0x00200000, + .type = MT_DEVICE + } +}; + +void __init pxa3xx_map_io(void) +{ + pxa_map_io(); + iotable_init(ARRAY_AND_SIZE(pxa3xx_io_desc)); + pxa3xx_get_clk_frequency_khz(1); +} + /* * device registration specific to PXA3xx. */ @@ -615,7 +435,9 @@ static struct sys_device pxa3xx_sysdev[] = { .cls = &pxa3xx_mfp_sysclass, }, { .cls = &pxa_gpio_sysclass, - }, + }, { + .cls = &pxa3xx_clock_sysclass, + } }; static int __init pxa3xx_init(void) diff --git a/arch/arm/mach-pxa/pxa930.c b/arch/arm/mach-pxa/pxa930.c index 7d29dd3..8aeacf9 100644 --- a/arch/arm/mach-pxa/pxa930.c +++ b/arch/arm/mach-pxa/pxa930.c @@ -192,7 +192,7 @@ static struct mfp_addr_map pxa935_mfp_addr_map[] __initdata = { static int __init pxa930_init(void) { - if (cpu_is_pxa930() || cpu_is_pxa935() || cpu_is_pxa950()) { + if (cpu_is_pxa93x()) { mfp_init_base(io_p2v(MFPR_BASE)); mfp_init_addr(pxa930_mfp_addr_map); } diff --git a/arch/arm/mach-pxa/pxa95x.c b/arch/arm/mach-pxa/pxa95x.c new file mode 100644 index 0000000..437980f --- /dev/null +++ b/arch/arm/mach-pxa/pxa95x.c @@ -0,0 +1,308 @@ +/* + * linux/arch/arm/mach-pxa/pxa95x.c + * + * code specific to PXA95x aka MGx + * + * Copyright (C) 2009-2010 Marvell International Ltd. + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + */ + +#include <linux/module.h> +#include <linux/kernel.h> +#include <linux/init.h> +#include <linux/pm.h> +#include <linux/platform_device.h> +#include <linux/irq.h> +#include <linux/io.h> +#include <linux/sysdev.h> + +#include <mach/hardware.h> +#include <mach/gpio.h> +#include <mach/pxa3xx-regs.h> +#include <mach/pxa930.h> +#include <mach/reset.h> +#include <mach/pm.h> +#include <mach/dma.h> +#include <mach/regs-intc.h> +#include <plat/i2c.h> + +#include "generic.h" +#include "devices.h" +#include "clock.h" + +static struct mfp_addr_map pxa95x_mfp_addr_map[] __initdata = { + + MFP_ADDR(GPIO0, 0x02e0), + MFP_ADDR(GPIO1, 0x02dc), + MFP_ADDR(GPIO2, 0x02e8), + MFP_ADDR(GPIO3, 0x02d8), + MFP_ADDR(GPIO4, 0x02e4), + MFP_ADDR(GPIO5, 0x02ec), + MFP_ADDR(GPIO6, 0x02f8), + MFP_ADDR(GPIO7, 0x02fc), + MFP_ADDR(GPIO8, 0x0300), + MFP_ADDR(GPIO9, 0x02d4), + MFP_ADDR(GPIO10, 0x02f4), + MFP_ADDR(GPIO11, 0x02f0), + MFP_ADDR(GPIO12, 0x0304), + MFP_ADDR(GPIO13, 0x0310), + MFP_ADDR(GPIO14, 0x0308), + MFP_ADDR(GPIO15, 0x030c), + MFP_ADDR(GPIO16, 0x04e8), + MFP_ADDR(GPIO17, 0x04f4), + MFP_ADDR(GPIO18, 0x04f8), + MFP_ADDR(GPIO19, 0x04fc), + MFP_ADDR(GPIO20, 0x0518), + MFP_ADDR(GPIO21, 0x051c), + MFP_ADDR(GPIO22, 0x04ec), + MFP_ADDR(GPIO23, 0x0500), + MFP_ADDR(GPIO24, 0x04f0), + MFP_ADDR(GPIO25, 0x0504), + MFP_ADDR(GPIO26, 0x0510), + MFP_ADDR(GPIO27, 0x0514), + MFP_ADDR(GPIO28, 0x0520), + MFP_ADDR(GPIO29, 0x0600), + MFP_ADDR(GPIO30, 0x0618), + MFP_ADDR(GPIO31, 0x0610), + MFP_ADDR(GPIO32, 0x060c), + MFP_ADDR(GPIO33, 0x061c), + MFP_ADDR(GPIO34, 0x0620), + MFP_ADDR(GPIO35, 0x0628), + MFP_ADDR(GPIO36, 0x062c), + MFP_ADDR(GPIO37, 0x0630), + MFP_ADDR(GPIO38, 0x0634), + MFP_ADDR(GPIO39, 0x0638), + MFP_ADDR(GPIO40, 0x063c), + MFP_ADDR(GPIO41, 0x0614), + MFP_ADDR(GPIO42, 0x0624), + MFP_ADDR(GPIO43, 0x0608), + MFP_ADDR(GPIO44, 0x0604), + MFP_ADDR(GPIO45, 0x050c), + MFP_ADDR(GPIO46, 0x0508), + MFP_ADDR(GPIO47, 0x02bc), + MFP_ADDR(GPIO48, 0x02b4), + MFP_ADDR(GPIO49, 0x02b8), + MFP_ADDR(GPIO50, 0x02c8), + MFP_ADDR(GPIO51, 0x02c0), + MFP_ADDR(GPIO52, 0x02c4), + MFP_ADDR(GPIO53, 0x02d0), + MFP_ADDR(GPIO54, 0x02cc), + MFP_ADDR(GPIO55, 0x029c), + MFP_ADDR(GPIO56, 0x02a0), + MFP_ADDR(GPIO57, 0x0294), + MFP_ADDR(GPIO58, 0x0298), + MFP_ADDR(GPIO59, 0x02a4), + MFP_ADDR(GPIO60, 0x02a8), + MFP_ADDR(GPIO61, 0x02b0), + MFP_ADDR(GPIO62, 0x02ac), + MFP_ADDR(GPIO63, 0x0640), + MFP_ADDR(GPIO64, 0x065c), + MFP_ADDR(GPIO65, 0x0648), + MFP_ADDR(GPIO66, 0x0644), + MFP_ADDR(GPIO67, 0x0674), + MFP_ADDR(GPIO68, 0x0658), + MFP_ADDR(GPIO69, 0x0654), + MFP_ADDR(GPIO70, 0x0660), + MFP_ADDR(GPIO71, 0x0668), + MFP_ADDR(GPIO72, 0x0664), + MFP_ADDR(GPIO73, 0x0650), + MFP_ADDR(GPIO74, 0x066c), + MFP_ADDR(GPIO75, 0x064c), + MFP_ADDR(GPIO76, 0x0670), + MFP_ADDR(GPIO77, 0x0678), + MFP_ADDR(GPIO78, 0x067c), + MFP_ADDR(GPIO79, 0x0694), + MFP_ADDR(GPIO80, 0x069c), + MFP_ADDR(GPIO81, 0x06a0), + MFP_ADDR(GPIO82, 0x06a4), + MFP_ADDR(GPIO83, 0x0698), + MFP_ADDR(GPIO84, 0x06bc), + MFP_ADDR(GPIO85, 0x06b4), + MFP_ADDR(GPIO86, 0x06b0), + MFP_ADDR(GPIO87, 0x06c0), + MFP_ADDR(GPIO88, 0x06c4), + MFP_ADDR(GPIO89, 0x06ac), + MFP_ADDR(GPIO90, 0x0680), + MFP_ADDR(GPIO91, 0x0684), + MFP_ADDR(GPIO92, 0x0688), + MFP_ADDR(GPIO93, 0x0690), + MFP_ADDR(GPIO94, 0x068c), + MFP_ADDR(GPIO95, 0x06a8), + MFP_ADDR(GPIO96, 0x06b8), + MFP_ADDR(GPIO97, 0x0410), + MFP_ADDR(GPIO98, 0x0418), + MFP_ADDR(GPIO99, 0x041c), + MFP_ADDR(GPIO100, 0x0414), + MFP_ADDR(GPIO101, 0x0408), + MFP_ADDR(GPIO102, 0x0324), + MFP_ADDR(GPIO103, 0x040c), + MFP_ADDR(GPIO104, 0x0400), + MFP_ADDR(GPIO105, 0x0328), + MFP_ADDR(GPIO106, 0x0404), + + MFP_ADDR(GPIO159, 0x0524), + MFP_ADDR(GPIO163, 0x0534), + MFP_ADDR(GPIO167, 0x0544), + MFP_ADDR(GPIO168, 0x0548), + MFP_ADDR(GPIO169, 0x054c), + MFP_ADDR(GPIO170, 0x0550), + MFP_ADDR(GPIO171, 0x0554), + MFP_ADDR(GPIO172, 0x0558), + MFP_ADDR(GPIO173, 0x055c), + + MFP_ADDR(nXCVREN, 0x0204), + MFP_ADDR(DF_CLE_nOE, 0x020c), + MFP_ADDR(DF_nADV1_ALE, 0x0218), + MFP_ADDR(DF_SCLK_E, 0x0214), + MFP_ADDR(DF_SCLK_S, 0x0210), + MFP_ADDR(nBE0, 0x021c), + MFP_ADDR(nBE1, 0x0220), + MFP_ADDR(DF_nADV2_ALE, 0x0224), + MFP_ADDR(DF_INT_RnB, 0x0228), + MFP_ADDR(DF_nCS0, 0x022c), + MFP_ADDR(DF_nCS1, 0x0230), + MFP_ADDR(nLUA, 0x0254), + MFP_ADDR(nLLA, 0x0258), + MFP_ADDR(DF_nWE, 0x0234), + MFP_ADDR(DF_nRE_nOE, 0x0238), + MFP_ADDR(DF_ADDR0, 0x024c), + MFP_ADDR(DF_ADDR1, 0x0250), + MFP_ADDR(DF_ADDR2, 0x025c), + MFP_ADDR(DF_ADDR3, 0x0260), + MFP_ADDR(DF_IO0, 0x023c), + MFP_ADDR(DF_IO1, 0x0240), + MFP_ADDR(DF_IO2, 0x0244), + MFP_ADDR(DF_IO3, 0x0248), + MFP_ADDR(DF_IO4, 0x0264), + MFP_ADDR(DF_IO5, 0x0268), + MFP_ADDR(DF_IO6, 0x026c), + MFP_ADDR(DF_IO7, 0x0270), + MFP_ADDR(DF_IO8, 0x0274), + MFP_ADDR(DF_IO9, 0x0278), + MFP_ADDR(DF_IO10, 0x027c), + MFP_ADDR(DF_IO11, 0x0280), + MFP_ADDR(DF_IO12, 0x0284), + MFP_ADDR(DF_IO13, 0x0288), + MFP_ADDR(DF_IO14, 0x028c), + MFP_ADDR(DF_IO15, 0x0290), + + MFP_ADDR(GSIM_UIO, 0x0314), + MFP_ADDR(GSIM_UCLK, 0x0318), + MFP_ADDR(GSIM_UDET, 0x031c), + MFP_ADDR(GSIM_nURST, 0x0320), + + MFP_ADDR(PMIC_INT, 0x06c8), + + MFP_ADDR(RDY, 0x0200), + + MFP_ADDR_END, +}; + +static DEFINE_CK(pxa95x_lcd, LCD, &clk_pxa3xx_hsio_ops); +static DEFINE_CLK(pxa95x_pout, &clk_pxa3xx_pout_ops, 13000000, 70); +static DEFINE_PXA3_CKEN(pxa95x_ffuart, FFUART, 14857000, 1); +static DEFINE_PXA3_CKEN(pxa95x_btuart, BTUART, 14857000, 1); +static DEFINE_PXA3_CKEN(pxa95x_stuart, STUART, 14857000, 1); +static DEFINE_PXA3_CKEN(pxa95x_i2c, I2C, 32842000, 0); +static DEFINE_PXA3_CKEN(pxa95x_keypad, KEYPAD, 32768, 0); +static DEFINE_PXA3_CKEN(pxa95x_ssp1, SSP1, 13000000, 0); +static DEFINE_PXA3_CKEN(pxa95x_ssp2, SSP2, 13000000, 0); +static DEFINE_PXA3_CKEN(pxa95x_ssp3, SSP3, 13000000, 0); +static DEFINE_PXA3_CKEN(pxa95x_ssp4, SSP4, 13000000, 0); +static DEFINE_PXA3_CKEN(pxa95x_pwm0, PWM0, 13000000, 0); +static DEFINE_PXA3_CKEN(pxa95x_pwm1, PWM1, 13000000, 0); + +static struct clk_lookup pxa95x_clkregs[] = { + INIT_CLKREG(&clk_pxa95x_pout, NULL, "CLK_POUT"), + /* Power I2C clock is always on */ + INIT_CLKREG(&clk_dummy, "pxa3xx-pwri2c.1", NULL), + INIT_CLKREG(&clk_pxa95x_lcd, "pxa2xx-fb", NULL), + INIT_CLKREG(&clk_pxa95x_ffuart, "pxa2xx-uart.0", NULL), + INIT_CLKREG(&clk_pxa95x_btuart, "pxa2xx-uart.1", NULL), + INIT_CLKREG(&clk_pxa95x_stuart, "pxa2xx-uart.2", NULL), + INIT_CLKREG(&clk_pxa95x_stuart, "pxa2xx-ir", "UARTCLK"), + INIT_CLKREG(&clk_pxa95x_i2c, "pxa2xx-i2c.0", NULL), + INIT_CLKREG(&clk_pxa95x_keypad, "pxa27x-keypad", NULL), + INIT_CLKREG(&clk_pxa95x_ssp1, "pxa27x-ssp.0", NULL), + INIT_CLKREG(&clk_pxa95x_ssp2, "pxa27x-ssp.1", NULL), + INIT_CLKREG(&clk_pxa95x_ssp3, "pxa27x-ssp.2", NULL), + INIT_CLKREG(&clk_pxa95x_ssp4, "pxa27x-ssp.3", NULL), + INIT_CLKREG(&clk_pxa95x_pwm0, "pxa27x-pwm.0", NULL), + INIT_CLKREG(&clk_pxa95x_pwm1, "pxa27x-pwm.1", NULL), +}; + +void __init pxa95x_init_irq(void) +{ + pxa_init_irq(96, NULL); + pxa_init_gpio(IRQ_GPIO_2_x, 2, 127, NULL); +} + +/* + * device registration specific to PXA93x. + */ + +void __init pxa95x_set_i2c_power_info(struct i2c_pxa_platform_data *info) +{ + pxa_register_device(&pxa3xx_device_i2c_power, info); +} + +static struct platform_device *devices[] __initdata = { + &sa1100_device_rtc, + &pxa_device_rtc, + &pxa27x_device_ssp1, + &pxa27x_device_ssp2, + &pxa27x_device_ssp3, + &pxa3xx_device_ssp4, + &pxa27x_device_pwm0, + &pxa27x_device_pwm1, +}; + +static struct sys_device pxa95x_sysdev[] = { + { + .cls = &pxa_irq_sysclass, + }, { + .cls = &pxa_gpio_sysclass, + }, { + .cls = &pxa3xx_clock_sysclass, + } +}; + +static int __init pxa95x_init(void) +{ + int ret = 0, i; + + if (cpu_is_pxa95x()) { + mfp_init_base(io_p2v(MFPR_BASE)); + mfp_init_addr(pxa95x_mfp_addr_map); + + reset_status = ARSR; + + /* + * clear RDH bit every time after reset + * + * Note: the last 3 bits DxS are write-1-to-clear so carefully + * preserve them here in case they will be referenced later + */ + ASCR &= ~(ASCR_RDH | ASCR_D1S | ASCR_D2S | ASCR_D3S); + + clkdev_add_table(pxa95x_clkregs, ARRAY_SIZE(pxa95x_clkregs)); + + if ((ret = pxa_init_dma(IRQ_DMA, 32))) + return ret; + + for (i = 0; i < ARRAY_SIZE(pxa95x_sysdev); i++) { + ret = sysdev_register(&pxa95x_sysdev[i]); + if (ret) + pr_err("failed to register sysdev[%d]\n", i); + } + + ret = platform_add_devices(devices, ARRAY_SIZE(devices)); + } + + return ret; +} + +postcore_initcall(pxa95x_init); diff --git a/arch/arm/mach-pxa/raumfeld.c b/arch/arm/mach-pxa/raumfeld.c index 4121d03..8361151 100644 --- a/arch/arm/mach-pxa/raumfeld.c +++ b/arch/arm/mach-pxa/raumfeld.c @@ -588,6 +588,9 @@ static struct pxafb_mach_info raumfeld_sharp_lcd_info = { .num_modes = 1, .video_mem_size = 0x400000, .lcd_conn = LCD_COLOR_TFT_16BPP | LCD_PCLK_EDGE_FALL, +#ifdef CONFIG_PXA3XX_GCU + .acceleration_enabled = 1, +#endif }; static void __init raumfeld_lcd_init(void) @@ -616,6 +619,8 @@ static void __init raumfeld_lcd_init(void) pr_warning("Unable to request GPIO_DISPLAY_ENABLE\n"); else gpio_direction_output(GPIO_DISPLAY_ENABLE, 1); + + platform_device_register(&pxa3xx_device_gcu); } /** @@ -1085,7 +1090,7 @@ static void __init raumfeld_speaker_init(void) MACHINE_START(RAUMFELD_RC, "Raumfeld Controller") .boot_params = RAUMFELD_SDRAM_BASE + 0x100, .init_machine = raumfeld_controller_init, - .map_io = pxa_map_io, + .map_io = pxa3xx_map_io, .init_irq = pxa3xx_init_irq, .timer = &pxa_timer, MACHINE_END @@ -1095,7 +1100,7 @@ MACHINE_END MACHINE_START(RAUMFELD_CONNECTOR, "Raumfeld Connector") .boot_params = RAUMFELD_SDRAM_BASE + 0x100, .init_machine = raumfeld_connector_init, - .map_io = pxa_map_io, + .map_io = pxa3xx_map_io, .init_irq = pxa3xx_init_irq, .timer = &pxa_timer, MACHINE_END @@ -1105,7 +1110,7 @@ MACHINE_END MACHINE_START(RAUMFELD_SPEAKER, "Raumfeld Speaker") .boot_params = RAUMFELD_SDRAM_BASE + 0x100, .init_machine = raumfeld_speaker_init, - .map_io = pxa_map_io, + .map_io = pxa3xx_map_io, .init_irq = pxa3xx_init_irq, .timer = &pxa_timer, MACHINE_END diff --git a/arch/arm/mach-pxa/saar.c b/arch/arm/mach-pxa/saar.c index ffa50e6..c1ca8cb 100644 --- a/arch/arm/mach-pxa/saar.c +++ b/arch/arm/mach-pxa/saar.c @@ -597,7 +597,7 @@ static void __init saar_init(void) MACHINE_START(SAAR, "PXA930 Handheld Platform (aka SAAR)") /* Maintainer: Eric Miao <eric.miao@marvell.com> */ .boot_params = 0xa0000100, - .map_io = pxa_map_io, + .map_io = pxa3xx_map_io, .init_irq = pxa3xx_init_irq, .timer = &pxa_timer, .init_machine = saar_init, diff --git a/arch/arm/mach-pxa/saarb.c b/arch/arm/mach-pxa/saarb.c new file mode 100644 index 0000000..e497922 --- /dev/null +++ b/arch/arm/mach-pxa/saarb.c @@ -0,0 +1,114 @@ +/* + * linux/arch/arm/mach-pxa/saarb.c + * + * Support for the Marvell Handheld Platform (aka SAARB) + * + * Copyright (C) 2007-2010 Marvell International Ltd. + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * publishhed by the Free Software Foundation. + */ + +#include <linux/init.h> +#include <linux/kernel.h> +#include <linux/i2c.h> +#include <linux/mfd/88pm860x.h> + +#include <asm/mach-types.h> +#include <asm/mach/arch.h> + +#include <mach/irqs.h> +#include <mach/hardware.h> +#include <mach/mfp.h> +#include <mach/mfp-pxa930.h> +#include <mach/gpio.h> + +#include <plat/i2c.h> + +#include "generic.h" + +#define SAARB_NR_IRQS (IRQ_BOARD_START + 40) + +static struct pm860x_touch_pdata saarb_touch = { + .gpadc_prebias = 1, + .slot_cycle = 1, + .tsi_prebias = 6, + .pen_prebias = 16, + .pen_prechg = 2, + .res_x = 300, +}; + +static struct pm860x_backlight_pdata saarb_backlight[] = { + { + .id = PM8606_ID_BACKLIGHT, + .iset = PM8606_WLED_CURRENT(24), + .flags = PM8606_BACKLIGHT1, + }, + {}, +}; + +static struct pm860x_led_pdata saarb_led[] = { + { + .id = PM8606_ID_LED, + .iset = PM8606_LED_CURRENT(12), + .flags = PM8606_LED1_RED, + }, { + .id = PM8606_ID_LED, + .iset = PM8606_LED_CURRENT(12), + .flags = PM8606_LED1_GREEN, + }, { + .id = PM8606_ID_LED, + .iset = PM8606_LED_CURRENT(12), + .flags = PM8606_LED1_BLUE, + }, { + .id = PM8606_ID_LED, + .iset = PM8606_LED_CURRENT(12), + .flags = PM8606_LED2_RED, + }, { + .id = PM8606_ID_LED, + .iset = PM8606_LED_CURRENT(12), + .flags = PM8606_LED2_GREEN, + }, { + .id = PM8606_ID_LED, + .iset = PM8606_LED_CURRENT(12), + .flags = PM8606_LED2_BLUE, + }, +}; + +static struct pm860x_platform_data saarb_pm8607_info = { + .touch = &saarb_touch, + .backlight = &saarb_backlight[0], + .led = &saarb_led[0], + .companion_addr = 0x10, + .irq_mode = 0, + .irq_base = IRQ_BOARD_START, + + .i2c_port = GI2C_PORT, +}; + +static struct i2c_board_info saarb_i2c_info[] = { + { + .type = "88PM860x", + .addr = 0x34, + .platform_data = &saarb_pm8607_info, + .irq = gpio_to_irq(mfp_to_gpio(MFP_PIN_GPIO83)), + }, +}; + +static void __init saarb_init(void) +{ + pxa_set_ffuart_info(NULL); + pxa_set_i2c_info(NULL); + i2c_register_board_info(0, ARRAY_AND_SIZE(saarb_i2c_info)); +} + +MACHINE_START(SAARB, "PXA955 Handheld Platform (aka SAARB)") + .boot_params = 0xa0000100, + .map_io = pxa_map_io, + .nr_irqs = SAARB_NR_IRQS, + .init_irq = pxa95x_init_irq, + .timer = &pxa_timer, + .init_machine = saarb_init, +MACHINE_END + diff --git a/arch/arm/mach-pxa/sharpsl_pm.c b/arch/arm/mach-pxa/sharpsl_pm.c index 8fed027..e68d46d 100644 --- a/arch/arm/mach-pxa/sharpsl_pm.c +++ b/arch/arm/mach-pxa/sharpsl_pm.c @@ -579,7 +579,8 @@ static int sharpsl_ac_check(void) static int sharpsl_pm_suspend(struct platform_device *pdev, pm_message_t state) { sharpsl_pm.flags |= SHARPSL_SUSPENDED; - flush_scheduled_work(); + flush_delayed_work_sync(&toggle_charger); + flush_delayed_work_sync(&sharpsl_bat); if (sharpsl_pm.charge_mode == CHRG_ON) sharpsl_pm.flags |= SHARPSL_DO_OFFLINE_CHRG; diff --git a/arch/arm/mach-pxa/sleep.S b/arch/arm/mach-pxa/sleep.S index ae00811..c551da8 100644 --- a/arch/arm/mach-pxa/sleep.S +++ b/arch/arm/mach-pxa/sleep.S @@ -14,7 +14,7 @@ #include <linux/linkage.h> #include <asm/assembler.h> #include <mach/hardware.h> - +#include <mach/smemc.h> #include <mach/pxa2xx-regs.h> #define MDREFR_KDIV 0x200a4000 // all banks diff --git a/arch/arm/mach-pxa/smemc.c b/arch/arm/mach-pxa/smemc.c index d6f6904..232b731 100644 --- a/arch/arm/mach-pxa/smemc.c +++ b/arch/arm/mach-pxa/smemc.c @@ -9,50 +9,37 @@ #include <linux/sysdev.h> #include <mach/hardware.h> - -#define SMEMC_PHYS_BASE (0x4A000000) -#define SMEMC_PHYS_SIZE (0x90) - -#define MSC0 (0x08) /* Static Memory Controller Register 0 */ -#define MSC1 (0x0C) /* Static Memory Controller Register 1 */ -#define SXCNFG (0x1C) /* Synchronous Static Memory Control Register */ -#define MEMCLKCFG (0x68) /* Clock Configuration */ -#define CSADRCFG0 (0x80) /* Address Configuration Register for CS0 */ -#define CSADRCFG1 (0x84) /* Address Configuration Register for CS1 */ -#define CSADRCFG2 (0x88) /* Address Configuration Register for CS2 */ -#define CSADRCFG3 (0x8C) /* Address Configuration Register for CS3 */ +#include <mach/smemc.h> #ifdef CONFIG_PM -static void __iomem *smemc_mmio_base; - static unsigned long msc[2]; static unsigned long sxcnfg, memclkcfg; static unsigned long csadrcfg[4]; static int pxa3xx_smemc_suspend(struct sys_device *dev, pm_message_t state) { - msc[0] = __raw_readl(smemc_mmio_base + MSC0); - msc[1] = __raw_readl(smemc_mmio_base + MSC1); - sxcnfg = __raw_readl(smemc_mmio_base + SXCNFG); - memclkcfg = __raw_readl(smemc_mmio_base + MEMCLKCFG); - csadrcfg[0] = __raw_readl(smemc_mmio_base + CSADRCFG0); - csadrcfg[1] = __raw_readl(smemc_mmio_base + CSADRCFG1); - csadrcfg[2] = __raw_readl(smemc_mmio_base + CSADRCFG2); - csadrcfg[3] = __raw_readl(smemc_mmio_base + CSADRCFG3); + msc[0] = __raw_readl(MSC0); + msc[1] = __raw_readl(MSC1); + sxcnfg = __raw_readl(SXCNFG); + memclkcfg = __raw_readl(MEMCLKCFG); + csadrcfg[0] = __raw_readl(CSADRCFG0); + csadrcfg[1] = __raw_readl(CSADRCFG1); + csadrcfg[2] = __raw_readl(CSADRCFG2); + csadrcfg[3] = __raw_readl(CSADRCFG3); return 0; } static int pxa3xx_smemc_resume(struct sys_device *dev) { - __raw_writel(msc[0], smemc_mmio_base + MSC0); - __raw_writel(msc[1], smemc_mmio_base + MSC1); - __raw_writel(sxcnfg, smemc_mmio_base + SXCNFG); - __raw_writel(memclkcfg, smemc_mmio_base + MEMCLKCFG); - __raw_writel(csadrcfg[0], smemc_mmio_base + CSADRCFG0); - __raw_writel(csadrcfg[1], smemc_mmio_base + CSADRCFG1); - __raw_writel(csadrcfg[2], smemc_mmio_base + CSADRCFG2); - __raw_writel(csadrcfg[3], smemc_mmio_base + CSADRCFG3); + __raw_writel(msc[0], MSC0); + __raw_writel(msc[1], MSC1); + __raw_writel(sxcnfg, SXCNFG); + __raw_writel(memclkcfg, MEMCLKCFG); + __raw_writel(csadrcfg[0], CSADRCFG0); + __raw_writel(csadrcfg[1], CSADRCFG1); + __raw_writel(csadrcfg[2], CSADRCFG2); + __raw_writel(csadrcfg[3], CSADRCFG3); return 0; } @@ -73,10 +60,6 @@ static int __init smemc_init(void) int ret = 0; if (cpu_is_pxa3xx()) { - smemc_mmio_base = ioremap(SMEMC_PHYS_BASE, SMEMC_PHYS_SIZE); - if (smemc_mmio_base == NULL) - return -ENODEV; - ret = sysdev_class_register(&smemc_sysclass); if (ret) return ret; diff --git a/arch/arm/mach-pxa/spitz.c b/arch/arm/mach-pxa/spitz.c index f736119..0bc9387 100644 --- a/arch/arm/mach-pxa/spitz.c +++ b/arch/arm/mach-pxa/spitz.c @@ -23,10 +23,11 @@ #include <linux/spi/spi.h> #include <linux/spi/ads7846.h> #include <linux/spi/corgi_lcd.h> -#include <linux/mtd/physmap.h> +#include <linux/spi/pxa2xx_spi.h> #include <linux/mtd/sharpsl.h> #include <linux/input/matrix_keypad.h> #include <linux/regulator/machine.h> +#include <linux/io.h> #include <asm/setup.h> #include <asm/mach-types.h> @@ -41,9 +42,9 @@ #include <mach/mmc.h> #include <mach/ohci.h> #include <mach/pxafb.h> -#include <mach/pxa2xx_spi.h> #include <mach/spitz.h> #include <mach/sharpsl_pm.h> +#include <mach/smemc.h> #include <plat/i2c.h> @@ -929,9 +930,10 @@ static void spitz_poweroff(void) static void spitz_restart(char mode, const char *cmd) { + uint32_t msc0 = __raw_readl(MSC0); /* Bootloader magic for a reboot */ - if ((MSC0 & 0xffff0000) == 0x7ff00000) - MSC0 = (MSC0 & 0xffff) | 0x7ee00000; + if ((msc0 & 0xffff0000) == 0x7ff00000) + __raw_writel((msc0 & 0xffff) | 0x7ee00000, MSC0); spitz_poweroff(); } @@ -980,7 +982,7 @@ static void __init spitz_fixup(struct machine_desc *desc, #ifdef CONFIG_MACH_SPITZ MACHINE_START(SPITZ, "SHARP Spitz") .fixup = spitz_fixup, - .map_io = pxa_map_io, + .map_io = pxa27x_map_io, .init_irq = pxa27x_init_irq, .init_machine = spitz_init, .timer = &pxa_timer, @@ -990,7 +992,7 @@ MACHINE_END #ifdef CONFIG_MACH_BORZOI MACHINE_START(BORZOI, "SHARP Borzoi") .fixup = spitz_fixup, - .map_io = pxa_map_io, + .map_io = pxa27x_map_io, .init_irq = pxa27x_init_irq, .init_machine = spitz_init, .timer = &pxa_timer, @@ -1000,7 +1002,7 @@ MACHINE_END #ifdef CONFIG_MACH_AKITA MACHINE_START(AKITA, "SHARP Akita") .fixup = spitz_fixup, - .map_io = pxa_map_io, + .map_io = pxa27x_map_io, .init_irq = pxa27x_init_irq, .init_machine = spitz_init, .timer = &pxa_timer, diff --git a/arch/arm/mach-pxa/stargate2.c b/arch/arm/mach-pxa/stargate2.c index 738adc1..9a14fdb 100644 --- a/arch/arm/mach-pxa/stargate2.c +++ b/arch/arm/mach-pxa/stargate2.c @@ -46,10 +46,11 @@ #include <plat/i2c.h> #include <mach/mmc.h> #include <mach/udc.h> -#include <mach/pxa2xx_spi.h> #include <mach/pxa27x-udc.h> +#include <mach/smemc.h> #include <linux/spi/spi.h> +#include <linux/spi/pxa2xx_spi.h> #include <linux/mfd/da903x.h> #include <linux/sht15.h> @@ -976,7 +977,7 @@ static void __init stargate2_init(void) { /* This is probably a board specific hack as this must be set prior to connecting the MFP stuff up. */ - MECR &= ~MECR_NOS; + __raw_writel(__raw_readl(MECR) & ~MECR_NOS, MECR); pxa2xx_mfp_config(ARRAY_AND_SIZE(stargate2_pin_config)); @@ -998,7 +999,7 @@ static void __init stargate2_init(void) #ifdef CONFIG_MACH_INTELMOTE2 MACHINE_START(INTELMOTE2, "IMOTE 2") - .map_io = pxa_map_io, + .map_io = pxa27x_map_io, .init_irq = pxa27x_init_irq, .timer = &pxa_timer, .init_machine = imote2_init, @@ -1008,7 +1009,7 @@ MACHINE_END #ifdef CONFIG_MACH_STARGATE2 MACHINE_START(STARGATE2, "Stargate 2") - .map_io = pxa_map_io, + .map_io = pxa27x_map_io, .nr_irqs = STARGATE_NR_IRQS, .init_irq = pxa27x_init_irq, .timer = &pxa_timer, diff --git a/arch/arm/mach-pxa/tavorevb.c b/arch/arm/mach-pxa/tavorevb.c index 2ea7545..9cecf83 100644 --- a/arch/arm/mach-pxa/tavorevb.c +++ b/arch/arm/mach-pxa/tavorevb.c @@ -490,7 +490,7 @@ static void __init tavorevb_init(void) MACHINE_START(TAVOREVB, "PXA930 Evaluation Board (aka TavorEVB)") /* Maintainer: Eric Miao <eric.miao@marvell.com> */ .boot_params = 0xa0000100, - .map_io = pxa_map_io, + .map_io = pxa3xx_map_io, .init_irq = pxa3xx_init_irq, .timer = &pxa_timer, .init_machine = tavorevb_init, diff --git a/arch/arm/mach-pxa/tavorevb3.c b/arch/arm/mach-pxa/tavorevb3.c index dc30116..70191a9 100644 --- a/arch/arm/mach-pxa/tavorevb3.c +++ b/arch/arm/mach-pxa/tavorevb3.c @@ -127,7 +127,7 @@ static void __init evb3_init(void) MACHINE_START(TAVOREVB3, "PXA950 Evaluation Board (aka TavorEVB3)") .boot_params = 0xa0000100, - .map_io = pxa_map_io, + .map_io = pxa3xx_map_io, .nr_irqs = TAVOREVB3_NR_IRQS, .init_irq = pxa3xx_init_irq, .timer = &pxa_timer, diff --git a/arch/arm/mach-pxa/time.c b/arch/arm/mach-pxa/time.c index 293e40a..e7f64d9 100644 --- a/arch/arm/mach-pxa/time.c +++ b/arch/arm/mach-pxa/time.c @@ -17,11 +17,11 @@ #include <linux/interrupt.h> #include <linux/clockchips.h> #include <linux/sched.h> -#include <linux/cnt32_to_63.h> #include <asm/div64.h> #include <asm/mach/irq.h> #include <asm/mach/time.h> +#include <asm/sched_clock.h> #include <mach/regs-ost.h> /* @@ -32,29 +32,18 @@ * long as there is always less than 582 seconds between successive * calls to sched_clock() which should always be the case in practice. */ +static DEFINE_CLOCK_DATA(cd); -#define OSCR2NS_SCALE_FACTOR 10 - -static unsigned long oscr2ns_scale; - -static void __init set_oscr2ns_scale(unsigned long oscr_rate) +unsigned long long notrace sched_clock(void) { - unsigned long long v = 1000000000ULL << OSCR2NS_SCALE_FACTOR; - do_div(v, oscr_rate); - oscr2ns_scale = v; - /* - * We want an even value to automatically clear the top bit - * returned by cnt32_to_63() without an additional run time - * instruction. So if the LSB is 1 then round it up. - */ - if (oscr2ns_scale & 1) - oscr2ns_scale++; + u32 cyc = OSCR; + return cyc_to_sched_clock(&cd, cyc, (u32)~0); } -unsigned long long sched_clock(void) +static void notrace pxa_update_sched_clock(void) { - unsigned long long v = cnt32_to_63(OSCR); - return (v * oscr2ns_scale) >> OSCR2NS_SCALE_FACTOR; + u32 cyc = OSCR; + update_sched_clock(&cd, cyc, (u32)~0); } @@ -127,7 +116,6 @@ static struct clocksource cksrc_pxa_oscr0 = { .rating = 200, .read = pxa_read_oscr, .mask = CLOCKSOURCE_MASK(32), - .shift = 20, .flags = CLOCK_SOURCE_IS_CONTINUOUS, }; @@ -145,7 +133,7 @@ static void __init pxa_timer_init(void) OIER = 0; OSSR = OSSR_M0 | OSSR_M1 | OSSR_M2 | OSSR_M3; - set_oscr2ns_scale(clock_tick_rate); + init_sched_clock(&cd, pxa_update_sched_clock, 32, clock_tick_rate); ckevt_pxa_osmr0.mult = div_sc(clock_tick_rate, NSEC_PER_SEC, ckevt_pxa_osmr0.shift); @@ -155,12 +143,9 @@ static void __init pxa_timer_init(void) clockevent_delta2ns(MIN_OSCR_DELTA * 2, &ckevt_pxa_osmr0) + 1; ckevt_pxa_osmr0.cpumask = cpumask_of(0); - cksrc_pxa_oscr0.mult = - clocksource_hz2mult(clock_tick_rate, cksrc_pxa_oscr0.shift); - setup_irq(IRQ_OST0, &pxa_ost0_irq); - clocksource_register(&cksrc_pxa_oscr0); + clocksource_register_hz(&cksrc_pxa_oscr0, clock_tick_rate); clockevents_register_device(&ckevt_pxa_osmr0); } diff --git a/arch/arm/mach-pxa/tosa.c b/arch/arm/mach-pxa/tosa.c index 0ee1df4..af152e7 100644 --- a/arch/arm/mach-pxa/tosa.c +++ b/arch/arm/mach-pxa/tosa.c @@ -32,6 +32,7 @@ #include <linux/gpio.h> #include <linux/pda_power.h> #include <linux/spi/spi.h> +#include <linux/spi/pxa2xx_spi.h> #include <linux/input/matrix_keypad.h> #include <asm/setup.h> @@ -44,8 +45,8 @@ #include <mach/mmc.h> #include <mach/udc.h> #include <mach/tosa_bt.h> -#include <mach/pxa2xx_spi.h> #include <mach/audio.h> +#include <mach/smemc.h> #include <asm/mach/arch.h> #include <mach/tosa.h> @@ -893,9 +894,11 @@ static void tosa_poweroff(void) static void tosa_restart(char mode, const char *cmd) { + uint32_t msc0 = __raw_readl(MSC0); + /* Bootloader magic for a reboot */ - if((MSC0 & 0xffff0000) == 0x7ff00000) - MSC0 = (MSC0 & 0xffff) | 0x7ee00000; + if((msc0 & 0xffff0000) == 0x7ff00000) + __raw_writel((msc0 & 0xffff) | 0x7ee00000, MSC0); tosa_poweroff(); } @@ -953,7 +956,7 @@ static void __init fixup_tosa(struct machine_desc *desc, MACHINE_START(TOSA, "SHARP Tosa") .fixup = fixup_tosa, - .map_io = pxa_map_io, + .map_io = pxa25x_map_io, .nr_irqs = TOSA_NR_IRQS, .init_irq = pxa25x_init_irq, .init_machine = tosa_init, diff --git a/arch/arm/mach-pxa/trizeps4.c b/arch/arm/mach-pxa/trizeps4.c index 565d062..423261d 100644 --- a/arch/arm/mach-pxa/trizeps4.c +++ b/arch/arm/mach-pxa/trizeps4.c @@ -40,13 +40,13 @@ #include <asm/mach/flash.h> #include <mach/pxa27x.h> -#include <mach/pxa2xx_spi.h> #include <mach/trizeps4.h> #include <mach/audio.h> #include <mach/pxafb.h> #include <mach/mmc.h> #include <mach/irda.h> #include <mach/ohci.h> +#include <mach/smemc.h> #include <plat/i2c.h> #include "generic.h" @@ -539,10 +539,10 @@ static void __init trizeps4_init(void) static void __init trizeps4_map_io(void) { - pxa_map_io(); + pxa27x_map_io(); iotable_init(trizeps4_io_desc, ARRAY_SIZE(trizeps4_io_desc)); - if ((MSC0 & 0x8) && (BOOT_DEF & 0x1)) { + if ((__raw_readl(MSC0) & 0x8) && (__raw_readl(BOOT_DEF) & 0x1)) { /* if flash is 16 bit wide its a Trizeps4 WL */ __machine_arch_type = MACH_TYPE_TRIZEPS4WL; trizeps4_flash_data[0].width = 2; diff --git a/arch/arm/mach-pxa/viper.c b/arch/arm/mach-pxa/viper.c index 438fc9a..de69b20 100644 --- a/arch/arm/mach-pxa/viper.c +++ b/arch/arm/mach-pxa/viper.c @@ -983,7 +983,7 @@ static struct map_desc viper_io_desc[] __initdata = { static void __init viper_map_io(void) { - pxa_map_io(); + pxa25x_map_io(); iotable_init(viper_io_desc, ARRAY_SIZE(viper_io_desc)); diff --git a/arch/arm/mach-pxa/vpac270.c b/arch/arm/mach-pxa/vpac270.c index f45ac09..b9b5797 100644 --- a/arch/arm/mach-pxa/vpac270.c +++ b/arch/arm/mach-pxa/vpac270.c @@ -719,7 +719,7 @@ static void __init vpac270_init(void) MACHINE_START(VPAC270, "Voipac PXA270") .boot_params = 0xa0000100, - .map_io = pxa_map_io, + .map_io = pxa27x_map_io, .init_irq = pxa27x_init_irq, .timer = &pxa_timer, .init_machine = vpac270_init diff --git a/arch/arm/mach-pxa/xcep.c b/arch/arm/mach-pxa/xcep.c index 3260ce7..51c0281 100644 --- a/arch/arm/mach-pxa/xcep.c +++ b/arch/arm/mach-pxa/xcep.c @@ -31,6 +31,7 @@ #include <mach/hardware.h> #include <mach/pxa2xx-regs.h> #include <mach/mfp-pxa25x.h> +#include <mach/smemc.h> #include "generic.h" @@ -172,9 +173,9 @@ static void __init xcep_init(void) /* See Intel XScale Developer's Guide for details */ /* Set RDF and RDN to appropriate values (chip select 3 (smc91x)) */ - MSC1 = (MSC1 & 0xffff) | 0xD5540000; + __raw_writel((__raw_readl(MSC1) & 0xffff) | 0xD5540000, MSC1); /* Set RDF and RDN to appropriate values (chip select 5 (fpga)) */ - MSC2 = (MSC2 & 0xffff) | 0x72A00000; + __raw_writel((__raw_readl(MSC2) & 0xffff) | 0x72A00000, MSC2); platform_add_devices(ARRAY_AND_SIZE(devices)); pxa_set_i2c_info(&xcep_i2c_platform_data); @@ -183,7 +184,7 @@ static void __init xcep_init(void) MACHINE_START(XCEP, "Iskratel XCEP") .boot_params = 0xa0000100, .init_machine = xcep_init, - .map_io = pxa_map_io, + .map_io = pxa25x_map_io, .init_irq = pxa25x_init_irq, .timer = &pxa_timer, MACHINE_END diff --git a/arch/arm/mach-pxa/z2.c b/arch/arm/mach-pxa/z2.c index fefde98..a323e07 100644 --- a/arch/arm/mach-pxa/z2.c +++ b/arch/arm/mach-pxa/z2.c @@ -20,6 +20,7 @@ #include <linux/z2_battery.h> #include <linux/dma-mapping.h> #include <linux/spi/spi.h> +#include <linux/spi/pxa2xx_spi.h> #include <linux/spi/libertas_spi.h> #include <linux/spi/lms283gf05.h> #include <linux/power_supply.h> @@ -38,7 +39,6 @@ #include <mach/pxafb.h> #include <mach/mmc.h> #include <plat/pxa27x_keypad.h> -#include <mach/pxa2xx_spi.h> #include <plat/i2c.h> @@ -704,7 +704,7 @@ static void __init z2_init(void) MACHINE_START(ZIPIT2, "Zipit Z2") .boot_params = 0xa0000100, - .map_io = pxa_map_io, + .map_io = pxa27x_map_io, .init_irq = pxa27x_init_irq, .timer = &pxa_timer, .init_machine = z2_init, diff --git a/arch/arm/mach-pxa/zeus.c b/arch/arm/mach-pxa/zeus.c index dea46a2..bf034c7 100644 --- a/arch/arm/mach-pxa/zeus.c +++ b/arch/arm/mach-pxa/zeus.c @@ -20,6 +20,7 @@ #include <linux/dm9000.h> #include <linux/mmc/host.h> #include <linux/spi/spi.h> +#include <linux/spi/pxa2xx_spi.h> #include <linux/mtd/mtd.h> #include <linux/mtd/partitions.h> #include <linux/mtd/physmap.h> @@ -41,12 +42,12 @@ #include <mach/pxa27x-udc.h> #include <mach/udc.h> #include <mach/pxafb.h> -#include <mach/pxa2xx_spi.h> #include <mach/mfp-pxa27x.h> #include <mach/pm.h> #include <mach/audio.h> #include <mach/arcom-pcmcia.h> #include <mach/zeus.h> +#include <mach/smemc.h> #include "generic.h" @@ -823,13 +824,16 @@ static mfp_cfg_t zeus_pin_config[] __initdata = { static void __init zeus_init(void) { u16 dm9000_msc = DM9K_MSC_VALUE; + u32 msc0, msc1; system_rev = __raw_readw(ZEUS_CPLD_VERSION); pr_info("Zeus CPLD V%dI%d\n", (system_rev & 0xf0) >> 4, (system_rev & 0x0f)); /* Fix timings for dm9000s (CS1/CS2)*/ - MSC0 = (MSC0 & 0xffff) | (dm9000_msc << 16); - MSC1 = (MSC1 & 0xffff0000) | dm9000_msc; + msc0 = __raw_readl(MSC0) & 0x0000ffff | (dm9000_msc << 16); + msc1 = __raw_readl(MSC1) & 0xffff0000 | dm9000_msc; + __raw_writel(msc0, MSC0); + __raw_writel(msc1, MSC1); pm_power_off = zeus_power_off; zeus_setup_apm(); @@ -883,7 +887,7 @@ static struct map_desc zeus_io_desc[] __initdata = { static void __init zeus_map_io(void) { - pxa_map_io(); + pxa27x_map_io(); iotable_init(zeus_io_desc, ARRAY_SIZE(zeus_io_desc)); diff --git a/arch/arm/mach-pxa/zylonite.c b/arch/arm/mach-pxa/zylonite.c index 702f7a6..a4c784a 100644 --- a/arch/arm/mach-pxa/zylonite.c +++ b/arch/arm/mach-pxa/zylonite.c @@ -423,7 +423,7 @@ static void __init zylonite_init(void) MACHINE_START(ZYLONITE, "PXA3xx Platform Development Kit (aka Zylonite)") .boot_params = 0xa0000100, - .map_io = pxa_map_io, + .map_io = pxa3xx_map_io, .nr_irqs = ZYLONITE_NR_IRQS, .init_irq = pxa3xx_init_irq, .timer = &pxa_timer, |