diff options
Diffstat (limited to 'arch/arm/mach-u300/core.c')
-rw-r--r-- | arch/arm/mach-u300/core.c | 113 |
1 files changed, 112 insertions, 1 deletions
diff --git a/arch/arm/mach-u300/core.c b/arch/arm/mach-u300/core.c index 8cfca45..6e5744a 100644 --- a/arch/arm/mach-u300/core.c +++ b/arch/arm/mach-u300/core.c @@ -22,7 +22,118 @@ #include <asm/mach/map.h> #include <asm/mach/arch.h> -#include "u300-regs.h" +/* + * These are the large blocks of memory allocated for I/O. + * the defines are used for setting up the I/O memory mapping. + */ + +/* NAND Flash CS0 */ +#define U300_NAND_CS0_PHYS_BASE 0x80000000 +/* NFIF */ +#define U300_NAND_IF_PHYS_BASE 0x9f800000 +/* ALE, CLE offset for FSMC NAND */ +#define PLAT_NAND_CLE (1 << 16) +#define PLAT_NAND_ALE (1 << 17) +/* AHB Peripherals */ +#define U300_AHB_PER_PHYS_BASE 0xa0000000 +#define U300_AHB_PER_VIRT_BASE 0xff010000 +/* FAST Peripherals */ +#define U300_FAST_PER_PHYS_BASE 0xc0000000 +#define U300_FAST_PER_VIRT_BASE 0xff020000 +/* SLOW Peripherals */ +#define U300_SLOW_PER_PHYS_BASE 0xc0010000 +#define U300_SLOW_PER_VIRT_BASE 0xff000000 +/* Boot ROM */ +#define U300_BOOTROM_PHYS_BASE 0xffff0000 +#define U300_BOOTROM_VIRT_BASE 0xffff0000 +/* SEMI config base */ +#define U300_SEMI_CONFIG_BASE 0x2FFE0000 + +/* + * AHB peripherals + */ + +/* AHB Peripherals Bridge Controller */ +#define U300_AHB_BRIDGE_BASE (U300_AHB_PER_PHYS_BASE+0x0000) +/* Vectored Interrupt Controller 0, servicing 32 interrupts */ +#define U300_INTCON0_BASE (U300_AHB_PER_PHYS_BASE+0x1000) +#define U300_INTCON0_VBASE IOMEM(U300_AHB_PER_VIRT_BASE+0x1000) +/* Vectored Interrupt Controller 1, servicing 32 interrupts */ +#define U300_INTCON1_BASE (U300_AHB_PER_PHYS_BASE+0x2000) +#define U300_INTCON1_VBASE IOMEM(U300_AHB_PER_VIRT_BASE+0x2000) +/* Memory Stick Pro (MSPRO) controller */ +#define U300_MSPRO_BASE (U300_AHB_PER_PHYS_BASE+0x3000) +/* EMIF Configuration Area */ +#define U300_EMIF_CFG_BASE (U300_AHB_PER_PHYS_BASE+0x4000) + +/* + * FAST peripherals + */ + +/* FAST bridge control */ +#define U300_FAST_BRIDGE_BASE (U300_FAST_PER_PHYS_BASE+0x0000) +/* MMC/SD controller */ +#define U300_MMCSD_BASE (U300_FAST_PER_PHYS_BASE+0x1000) +/* PCM I2S0 controller */ +#define U300_PCM_I2S0_BASE (U300_FAST_PER_PHYS_BASE+0x2000) +/* PCM I2S1 controller */ +#define U300_PCM_I2S1_BASE (U300_FAST_PER_PHYS_BASE+0x3000) +/* I2C0 controller */ +#define U300_I2C0_BASE (U300_FAST_PER_PHYS_BASE+0x4000) +/* I2C1 controller */ +#define U300_I2C1_BASE (U300_FAST_PER_PHYS_BASE+0x5000) +/* SPI controller */ +#define U300_SPI_BASE (U300_FAST_PER_PHYS_BASE+0x6000) +/* Fast UART1 on U335 only */ +#define U300_UART1_BASE (U300_FAST_PER_PHYS_BASE+0x7000) + +/* + * SLOW peripherals + */ + +/* SLOW bridge control */ +#define U300_SLOW_BRIDGE_BASE (U300_SLOW_PER_PHYS_BASE) +/* SYSCON */ +#define U300_SYSCON_BASE (U300_SLOW_PER_PHYS_BASE+0x1000) +#define U300_SYSCON_VBASE IOMEM(U300_SLOW_PER_VIRT_BASE+0x1000) +/* Watchdog */ +#define U300_WDOG_BASE (U300_SLOW_PER_PHYS_BASE+0x2000) +/* UART0 */ +#define U300_UART0_BASE (U300_SLOW_PER_PHYS_BASE+0x3000) +/* APP side special timer */ +#define U300_TIMER_APP_BASE (U300_SLOW_PER_PHYS_BASE+0x4000) +#define U300_TIMER_APP_VBASE IOMEM(U300_SLOW_PER_VIRT_BASE+0x4000) +/* Keypad */ +#define U300_KEYPAD_BASE (U300_SLOW_PER_PHYS_BASE+0x5000) +/* GPIO */ +#define U300_GPIO_BASE (U300_SLOW_PER_PHYS_BASE+0x6000) +/* RTC */ +#define U300_RTC_BASE (U300_SLOW_PER_PHYS_BASE+0x7000) +/* Bus tracer */ +#define U300_BUSTR_BASE (U300_SLOW_PER_PHYS_BASE+0x8000) +/* Event handler (hardware queue) */ +#define U300_EVHIST_BASE (U300_SLOW_PER_PHYS_BASE+0x9000) +/* Genric Timer */ +#define U300_TIMER_BASE (U300_SLOW_PER_PHYS_BASE+0xa000) +/* PPM */ +#define U300_PPM_BASE (U300_SLOW_PER_PHYS_BASE+0xb000) + +/* + * REST peripherals + */ + +/* ISP (image signal processor) */ +#define U300_ISP_BASE (0xA0008000) +/* DMA Controller base */ +#define U300_DMAC_BASE (0xC0020000) +/* MSL Base */ +#define U300_MSL_BASE (0xc0022000) +/* APEX Base */ +#define U300_APEX_BASE (0xc0030000) +/* Video Encoder Base */ +#define U300_VIDEOENC_BASE (0xc0080000) +/* XGAM Base */ +#define U300_XGAM_BASE (0xd0000000) /* * SYSCON addresses applicable to the core machine. |