diff options
Diffstat (limited to 'arch')
| -rw-r--r-- | arch/arm/boot/dts/Makefile | 3 | ||||
| -rw-r--r-- | arch/arm/boot/dts/dm8148-evm.dts | 55 | ||||
| -rw-r--r-- | arch/arm/boot/dts/dm8148-t410.dts | 70 | ||||
| -rw-r--r-- | arch/arm/boot/dts/dm814x-clocks.dtsi | 109 | ||||
| -rw-r--r-- | arch/arm/boot/dts/dm814x.dtsi | 259 | ||||
| -rw-r--r-- | arch/arm/boot/dts/dra62x-clocks.dtsi | 23 | ||||
| -rw-r--r-- | arch/arm/boot/dts/dra62x-j5eco-evm.dts | 80 | ||||
| -rw-r--r-- | arch/arm/boot/dts/dra62x.dtsi | 23 | ||||
| -rw-r--r-- | arch/arm/mach-omap2/io.c | 3 | ||||
| -rw-r--r-- | arch/arm/mach-omap2/omap_hwmod_81xx_data.c | 12 | ||||
| -rw-r--r-- | arch/arm/mach-omap2/prm_common.c | 6 |
11 files changed, 585 insertions, 58 deletions
diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile index c34dcbd..f70d4c1 100644 --- a/arch/arm/boot/dts/Makefile +++ b/arch/arm/boot/dts/Makefile @@ -464,7 +464,8 @@ dtb-$(CONFIG_ARCH_OMAP3) += \ dtb-$(CONFIG_SOC_TI81XX) += \ dm8148-evm.dtb \ dm8148-t410.dtb \ - dm8168-evm.dtb + dm8168-evm.dtb \ + dra62x-j5eco-evm.dtb dtb-$(CONFIG_SOC_AM33XX) += \ am335x-baltos-ir5221.dtb \ am335x-base0033.dtb \ diff --git a/arch/arm/boot/dts/dm8148-evm.dts b/arch/arm/boot/dts/dm8148-evm.dts index 109fd47..e070862 100644 --- a/arch/arm/boot/dts/dm8148-evm.dts +++ b/arch/arm/boot/dts/dm8148-evm.dts @@ -15,6 +15,14 @@ device_type = "memory"; reg = <0x80000000 0x40000000>; /* 1 GB */ }; + + /* MIC94060YC6 controlled by SD1_POW pin */ + vmmcsd_fixed: fixedregulator@0 { + compatible = "regulator-fixed"; + regulator-name = "vmmcsd_fixed"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + }; }; &cpsw_emac0 { @@ -26,3 +34,50 @@ phy_id = <&davinci_mdio>, <1>; phy-mode = "rgmii"; }; + +&mmc2 { + pinctrl-names = "default"; + pinctrl-0 = <&sd1_pins>; + vmmc-supply = <&vmmcsd_fixed>; + bus-width = <4>; + cd-gpios = <&gpio2 6 GPIO_ACTIVE_LOW>; +}; + +&pincntl { + sd1_pins: pinmux_sd1_pins { + pinctrl-single,pins = < + DM814X_IOPAD(0x0800, PIN_INPUT | 0x1) /* SD1_CLK */ + DM814X_IOPAD(0x0804, PIN_INPUT_PULLUP | 0x1) /* SD1_CMD */ + DM814X_IOPAD(0x0808, PIN_INPUT_PULLUP | 0x1) /* SD1_DAT[0] */ + DM814X_IOPAD(0x080c, PIN_INPUT_PULLUP | 0x1) /* SD1_DAT[1] */ + DM814X_IOPAD(0x0810, PIN_INPUT_PULLUP | 0x1) /* SD1_DAT[2] */ + DM814X_IOPAD(0x0814, PIN_INPUT_PULLUP | 0x1) /* SD1_DAT[3] */ + DM814X_IOPAD(0x0924, PIN_OUTPUT | 0x40) /* SD1_POW */ + DM814X_IOPAD(0x093C, PIN_INPUT_PULLUP | 0x80) /* GP1[6] */ + >; + }; + + usb0_pins: pinmux_usb0_pins { + pinctrl-single,pins = < + DM814X_IOPAD(0x0c34, PIN_OUTPUT | 0x1) /* USB0_DRVVBUS */ + >; + }; + + usb1_pins: pinmux_usb1_pins { + pinctrl-single,pins = < + DM814X_IOPAD(0x0834, PIN_OUTPUT | 0x80) /* USB1_DRVVBUS */ + >; + }; +}; + +&usb0 { + pinctrl-names = "default"; + pinctrl-0 = <&usb0_pins>; + dr_mode = "host"; +}; + +&usb1 { + pinctrl-names = "default"; + pinctrl-0 = <&usb1_pins>; + dr_mode = "host"; +}; diff --git a/arch/arm/boot/dts/dm8148-t410.dts b/arch/arm/boot/dts/dm8148-t410.dts index 79838dd..5d4313f 100644 --- a/arch/arm/boot/dts/dm8148-t410.dts +++ b/arch/arm/boot/dts/dm8148-t410.dts @@ -15,6 +15,24 @@ device_type = "memory"; reg = <0x80000000 0x40000000>; /* 1 GB */ }; + + /* gpio9 seems to control USB VBUS regulator and/or hub power */ + usb_power: regulator@9 { + compatible = "regulator-fixed"; + regulator-name = "usb_power"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + gpio = <&gpio1 9 GPIO_ACTIVE_HIGH>; + enable-active-high; + regulator-always-on; + }; + + vmmcsd_fixed: fixedregulator@0 { + compatible = "regulator-fixed"; + regulator-name = "vmmcsd_fixed"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + }; }; &cpsw_emac0 { @@ -26,3 +44,55 @@ phy_id = <&davinci_mdio>, <1>; phy-mode = "rgmii"; }; + +&mmc3 { + pinctrl-names = "default"; + pinctrl-0 = <&sd2_pins>; + vmmc-supply = <&vmmcsd_fixed>; + bus-width = <8>; + dmas = <&edma_xbar 8 0 1 /* use SDTXEVT1 instead of MCASP0TX */ + &edma_xbar 9 0 2>; /* use SDRXEVT1 instead of MCASP0RX */ + dma-names = "tx", "rx"; +}; + +&pincntl { + sd2_pins: pinmux_sd2_pins { + pinctrl-single,pins = < + DM814X_IOPAD(0x09c0, PIN_INPUT_PULLUP | 0x1) /* SD2_DAT[7] */ + DM814X_IOPAD(0x09c4, PIN_INPUT_PULLUP | 0x1) /* SD2_DAT[6] */ + DM814X_IOPAD(0x09c8, PIN_INPUT_PULLUP | 0x1) /* SD2_DAT[5] */ + DM814X_IOPAD(0x09cc, PIN_INPUT_PULLUP | 0x1) /* SD2_DAT[4] */ + DM814X_IOPAD(0x09d0, PIN_INPUT_PULLUP | 0x1) /* SD2_DAT[3] */ + DM814X_IOPAD(0x09d4, PIN_INPUT_PULLUP | 0x1) /* SD2_DAT[2] */ + DM814X_IOPAD(0x09d8, PIN_INPUT_PULLUP | 0x1) /* SD2_DAT[1] */ + DM814X_IOPAD(0x09dc, PIN_INPUT_PULLUP | 0x1) /* SD2_DAT[0] */ + DM814X_IOPAD(0x09e0, PIN_INPUT | 0x1) /* SD2_CLK */ + DM814X_IOPAD(0x09f4, PIN_INPUT_PULLUP | 0x2) /* SD2_CMD */ + DM814X_IOPAD(0x0920, PIN_INPUT | 40) /* SD2_SDCD */ + >; + }; + + usb0_pins: pinmux_usb0_pins { + pinctrl-single,pins = < + DM814X_IOPAD(0x0c34, PIN_OUTPUT | 0x1) /* USB0_DRVVBUS */ + >; + }; + + usb1_pins: pinmux_usb1_pins { + pinctrl-single,pins = < + DM814X_IOPAD(0x0834, PIN_OUTPUT | 0x80) /* USB1_DRVVBUS */ + >; + }; +}; + +&usb0 { + pinctrl-names = "default"; + pinctrl-0 = <&usb0_pins>; + dr_mode = "host"; +}; + +&usb1 { + pinctrl-names = "default"; + pinctrl-0 = <&usb1_pins>; + dr_mode = "host"; +}; diff --git a/arch/arm/boot/dts/dm814x-clocks.dtsi b/arch/arm/boot/dts/dm814x-clocks.dtsi index ef1e8e7..2600158 100644 --- a/arch/arm/boot/dts/dm814x-clocks.dtsi +++ b/arch/arm/boot/dts/dm814x-clocks.dtsi @@ -4,25 +4,74 @@ * published by the Free Software Foundation. */ +&pllss_clocks { + timer1_fck: timer1_fck { + #clock-cells = <0>; + compatible = "ti,mux-clock"; + clocks = <&sysclk18_ck &aud_clkin0_ck &aud_clkin1_ck + &aud_clkin2_ck &devosc_ck &auxosc_ck &tclkin_ck>; + ti,bit-shift = <3>; + reg = <0x2e0>; + }; + + timer2_fck: timer2_fck { + #clock-cells = <0>; + compatible = "ti,mux-clock"; + clocks = <&sysclk18_ck &aud_clkin0_ck &aud_clkin1_ck + &aud_clkin2_ck &devosc_ck &auxosc_ck &tclkin_ck>; + ti,bit-shift = <6>; + reg = <0x2e0>; + }; + + sysclk18_ck: sysclk18_ck { + #clock-cells = <0>; + compatible = "ti,mux-clock"; + clocks = <&rtcosc_ck>, <&rtcdivider_ck>; + ti,bit-shift = <0>; + reg = <0x02f0>; + }; +}; + &scm_clocks { + devosc_ck: devosc_ck { + #clock-cells = <0>; + compatible = "ti,mux-clock"; + clocks = <&virt_20000000_ck>, <&virt_19200000_ck>; + ti,bit-shift = <21>; + reg = <0x0040>; + }; - tclkin_ck: tclkin_ck { + /* Optional auxosc, 20 - 30 MHz range, assume 27 MHz by default */ + auxosc_ck: auxosc_ck { + #clock-cells = <0>; + compatible = "fixed-clock"; + clock-frequency = <27000000>; + }; + + /* Optional 32768Hz crystal or clock on RTCOSC pins */ + rtcosc_ck: rtcosc_ck { #clock-cells = <0>; compatible = "fixed-clock"; clock-frequency = <32768>; }; - devosc_ck: devosc_ck { + /* Optional external clock on TCLKIN pin, set rate in baord dts file */ + tclkin_ck: tclkin_ck { + #clock-cells = <0>; + compatible = "fixed-clock"; + clock-frequency = <0>; + }; + + virt_20000000_ck: virt_20000000_ck { #clock-cells = <0>; compatible = "fixed-clock"; clock-frequency = <20000000>; }; - /* Optional auxosc, 20 - 30 MHz range, assume 27 MHz by default */ - auxosc_ck: auxosc_ck { + virt_19200000_ck: virt_19200000_ck { #clock-cells = <0>; compatible = "fixed-clock"; - clock-frequency = <27000000>; + clock-frequency = <19200000>; }; mpu_ck: mpu_ck { @@ -49,12 +98,6 @@ clock-frequency = <48000000>; }; - sysclk18_ck: sysclk18_ck { - #clock-cells = <0>; - compatible = "fixed-clock"; - clock-frequency = <32768>; - }; - cpsw_125mhz_gclk: cpsw_125mhz_gclk { #clock-cells = <0>; compatible = "fixed-clock"; @@ -69,7 +112,31 @@ }; -&pllss_clocks { +&prcm_clocks { + osc_src_ck: osc_src_ck { + #clock-cells = <0>; + compatible = "fixed-factor-clock"; + clocks = <&devosc_ck>; + clock-mult = <1>; + clock-div = <1>; + }; + + mpu_clksrc_ck: mpu_clksrc_ck { + #clock-cells = <0>; + compatible = "ti,mux-clock"; + clocks = <&devosc_ck>, <&rtcdivider_ck>; + ti,bit-shift = <0>; + reg = <0x0040>; + }; + + /* Fixed divider clock 0.0016384 * devosc */ + rtcdivider_ck: rtcdivider_ck { + #clock-cells = <0>; + compatible = "fixed-factor-clock"; + clocks = <&devosc_ck>; + clock-mult = <128>; + clock-div = <78125>; + }; aud_clkin0_ck: aud_clkin0_ck { #clock-cells = <0>; @@ -88,22 +155,4 @@ compatible = "fixed-clock"; clock-frequency = <20000000>; }; - - timer1_mux_ck: timer1_mux_ck { - #clock-cells = <0>; - compatible = "ti,mux-clock"; - clocks = <&sysclk18_ck &aud_clkin0_ck &aud_clkin1_ck - &aud_clkin2_ck &devosc_ck &auxosc_ck &tclkin_ck>; - ti,bit-shift = <3>; - reg = <0x2e0>; - }; - - timer2_mux_ck: timer2_mux_ck { - #clock-cells = <0>; - compatible = "ti,mux-clock"; - clocks = <&sysclk18_ck &aud_clkin0_ck &aud_clkin1_ck - &aud_clkin2_ck &devosc_ck &auxosc_ck &tclkin_ck>; - ti,bit-shift = <6>; - reg = <0x2e0>; - }; }; diff --git a/arch/arm/boot/dts/dm814x.dtsi b/arch/arm/boot/dts/dm814x.dtsi index 7988b42..a25cd51 100644 --- a/arch/arm/boot/dts/dm814x.dtsi +++ b/arch/arm/boot/dts/dm814x.dtsi @@ -5,7 +5,7 @@ */ #include <dt-bindings/gpio/gpio.h> -#include <dt-bindings/pinctrl/omap.h> +#include <dt-bindings/pinctrl/dm814x.h> #include "skeleton.dtsi" @@ -21,6 +21,10 @@ serial2 = &uart3; ethernet0 = &cpsw_emac0; ethernet1 = &cpsw_emac1; + usb0 = &usb0; + usb1 = &usb1; + phy0 = &usb0_phy; + phy1 = &usb1_phy; }; cpus { @@ -57,9 +61,118 @@ ranges; ti,hwmods = "l3_main"; + usb: usb@47400000 { + compatible = "ti,am33xx-usb"; + reg = <0x47400000 0x1000>; + ranges; + #address-cells = <1>; + #size-cells = <1>; + ti,hwmods = "usb_otg_hs"; + + usb0_phy: usb-phy@47401300 { + compatible = "ti,am335x-usb-phy"; + reg = <0x47401300 0x100>; + reg-names = "phy"; + ti,ctrl_mod = <&usb_ctrl_mod>; + }; + + usb0: usb@47401000 { + compatible = "ti,musb-am33xx"; + reg = <0x47401400 0x400 + 0x47401000 0x200>; + reg-names = "mc", "control"; + + interrupts = <18>; + interrupt-names = "mc"; + dr_mode = "otg"; + mentor,multipoint = <1>; + mentor,num-eps = <16>; + mentor,ram-bits = <12>; + mentor,power = <500>; + phys = <&usb0_phy>; + + dmas = <&cppi41dma 0 0 &cppi41dma 1 0 + &cppi41dma 2 0 &cppi41dma 3 0 + &cppi41dma 4 0 &cppi41dma 5 0 + &cppi41dma 6 0 &cppi41dma 7 0 + &cppi41dma 8 0 &cppi41dma 9 0 + &cppi41dma 10 0 &cppi41dma 11 0 + &cppi41dma 12 0 &cppi41dma 13 0 + &cppi41dma 14 0 &cppi41dma 0 1 + &cppi41dma 1 1 &cppi41dma 2 1 + &cppi41dma 3 1 &cppi41dma 4 1 + &cppi41dma 5 1 &cppi41dma 6 1 + &cppi41dma 7 1 &cppi41dma 8 1 + &cppi41dma 9 1 &cppi41dma 10 1 + &cppi41dma 11 1 &cppi41dma 12 1 + &cppi41dma 13 1 &cppi41dma 14 1>; + dma-names = + "rx1", "rx2", "rx3", "rx4", "rx5", "rx6", "rx7", + "rx8", "rx9", "rx10", "rx11", "rx12", "rx13", + "rx14", "rx15", + "tx1", "tx2", "tx3", "tx4", "tx5", "tx6", "tx7", + "tx8", "tx9", "tx10", "tx11", "tx12", "tx13", + "tx14", "tx15"; + }; + + usb1: usb@47401800 { + compatible = "ti,musb-am33xx"; + reg = <0x47401c00 0x400 + 0x47401800 0x200>; + reg-names = "mc", "control"; + interrupts = <19>; + interrupt-names = "mc"; + dr_mode = "otg"; + mentor,multipoint = <1>; + mentor,num-eps = <16>; + mentor,ram-bits = <12>; + mentor,power = <500>; + phys = <&usb1_phy>; + + dmas = <&cppi41dma 15 0 &cppi41dma 16 0 + &cppi41dma 17 0 &cppi41dma 18 0 + &cppi41dma 19 0 &cppi41dma 20 0 + &cppi41dma 21 0 &cppi41dma 22 0 + &cppi41dma 23 0 &cppi41dma 24 0 + &cppi41dma 25 0 &cppi41dma 26 0 + &cppi41dma 27 0 &cppi41dma 28 0 + &cppi41dma 29 0 &cppi41dma 15 1 + &cppi41dma 16 1 &cppi41dma 17 1 + &cppi41dma 18 1 &cppi41dma 19 1 + &cppi41dma 20 1 &cppi41dma 21 1 + &cppi41dma 22 1 &cppi41dma 23 1 + &cppi41dma 24 1 &cppi41dma 25 1 + &cppi41dma 26 1 &cppi41dma 27 1 + &cppi41dma 28 1 &cppi41dma 29 1>; + dma-names = + "rx1", "rx2", "rx3", "rx4", "rx5", "rx6", "rx7", + "rx8", "rx9", "rx10", "rx11", "rx12", "rx13", + "rx14", "rx15", + "tx1", "tx2", "tx3", "tx4", "tx5", "tx6", "tx7", + "tx8", "tx9", "tx10", "tx11", "tx12", "tx13", + "tx14", "tx15"; + }; + + cppi41dma: dma-controller@47402000 { + compatible = "ti,am3359-cppi41"; + reg = <0x47400000 0x1000 + 0x47402000 0x1000 + 0x47403000 0x1000 + 0x47404000 0x4000>; + reg-names = "glue", "controller", "scheduler", "queuemgr"; + interrupts = <17>; + interrupt-names = "glue"; + #dma-cells = <2>; + #dma-channels = <30>; + #dma-requests = <256>; + }; + }; + /* - * See TRM "Table 1-317. L4LS Instance Summary", just deduct - * 0x1000 from the 1-317 addresses to get the device address + * See TRM "Table 1-317. L4LS Instance Summary" for hints. + * It shows the module target agent registers though, so the + * actual device is typically 0x1000 before the target agent + * except in cases where the module is larger than 0x1000. */ l4ls: l4ls@48000000 { compatible = "ti,dm814-l4ls", "simple-bus"; @@ -124,8 +237,8 @@ interrupts = <65>; ti,spi-num-cs = <4>; ti,hwmods = "mcspi1"; - dmas = <&edma 16 &edma 17 - &edma 18 &edma 19>; + dmas = <&edma 16 0 &edma 17 0 + &edma 18 0 &edma 19 0>; dma-names = "tx0", "rx0", "tx1", "rx1"; }; @@ -143,7 +256,7 @@ reg = <0x20000 0x2000>; clock-frequency = <48000000>; interrupts = <72>; - dmas = <&edma 26 &edma 27>; + dmas = <&edma 26 0 &edma 27 0>; dma-names = "tx", "rx"; }; @@ -153,7 +266,7 @@ reg = <0x22000 0x2000>; clock-frequency = <48000000>; interrupts = <73>; - dmas = <&edma 28 &edma 29>; + dmas = <&edma 28 0 &edma 29 0>; dma-names = "tx", "rx"; }; @@ -163,7 +276,7 @@ reg = <0x24000 0x2000>; clock-frequency = <48000000>; interrupts = <74>; - dmas = <&edma 30 &edma 31>; + dmas = <&edma 30 0 &edma 31 0>; dma-names = "tx", "rx"; }; @@ -181,12 +294,34 @@ ti,hwmods = "timer3"; }; + mmc1: mmc@60000 { + compatible = "ti,omap4-hsmmc"; + ti,hwmods = "mmc1"; + dmas = <&edma 24 0 + &edma 25 0>; + dma-names = "tx", "rx"; + interrupts = <64>; + interrupt-parent = <&intc>; + reg = <0x60000 0x1000>; + }; + + mmc2: mmc@1d8000 { + compatible = "ti,omap4-hsmmc"; + ti,hwmods = "mmc2"; + dmas = <&edma 2 0 + &edma 3 0>; + dma-names = "tx", "rx"; + interrupts = <28>; + interrupt-parent = <&intc>; + reg = <0x1d8000 0x1000>; + }; + control: control@140000 { compatible = "ti,dm814-scm", "simple-bus"; - reg = <0x140000 0x16d000>; + reg = <0x140000 0x20000>; #address-cells = <1>; #size-cells = <1>; - ranges = <0 0x160000 0x16d000>; + ranges = <0 0x140000 0x20000>; scm_conf: scm_conf@0 { compatible = "syscon"; @@ -203,19 +338,52 @@ }; }; + usb_ctrl_mod: control@620 { + compatible = "ti,am335x-usb-ctrl-module"; + reg = <0x620 0x10 + 0x648 0x4>; + reg-names = "phy_ctrl", "wakeup"; + }; + + edma_xbar: dma-router@f90 { + compatible = "ti,am335x-edma-crossbar"; + reg = <0xf90 0x40>; + #dma-cells = <3>; + dma-requests = <32>; + dma-masters = <&edma>; + }; + + /* + * Note that silicon revision 2.1 and older + * require input enabled (bit 18 set) for all + * 3.3V I/Os to avoid cumulative hardware damage. + * For more info, see errata advisory 2.1.87. + * We leave bit 18 out of function-mask and rely + * on the bootloader for it. + */ pincntl: pinmux@800 { compatible = "pinctrl-single"; - reg = <0x800 0xc38>; + reg = <0x800 0x438>; #address-cells = <1>; #size-cells = <0>; pinctrl-single,register-width = <32>; - pinctrl-single,function-mask = <0x300ff>; + pinctrl-single,function-mask = <0x307ff>; + }; + + usb1_phy: usb-phy@1b00 { + compatible = "ti,am335x-usb-phy"; + reg = <0x1b00 0x100>; + reg-names = "phy"; + ti,ctrl_mod = <&usb_ctrl_mod>; }; }; prcm: prcm@180000 { compatible = "ti,dm814-prcm", "simple-bus"; - reg = <0x180000 0x4000>; + reg = <0x180000 0x2000>; + #address-cells = <1>; + #size-cells = <1>; + ranges = <0 0x180000 0x2000>; prcm_clocks: clocks { #address-cells = <1>; @@ -226,9 +394,13 @@ }; }; + /* See TRM PLL_SUBSYS_BASE and "PLLSS Registers" */ pllss: pllss@1c5000 { compatible = "ti,dm814-pllss", "simple-bus"; - reg = <0x1c5000 0x2000>; + reg = <0x1c5000 0x1000>; + #address-cells = <1>; + #size-cells = <1>; + ranges = <0 0x1c5000 0x1000>; pllss_clocks: clocks { #address-cells = <1>; @@ -254,13 +426,62 @@ reg = <0x48200000 0x1000>; }; + /* Board must configure evtmux with edma_xbar for EDMA */ + mmc3: mmc@47810000 { + compatible = "ti,omap4-hsmmc"; + ti,hwmods = "mmc3"; + interrupts = <29>; + interrupt-parent = <&intc>; + reg = <0x47810000 0x1000>; + }; + edma: edma@49000000 { - compatible = "ti,edma3"; - ti,hwmods = "tpcc", "tptc0", "tptc1", "tptc2"; - reg = <0x49000000 0x10000>, - <0x44e10f90 0x40>; + compatible = "ti,edma3-tpcc"; + ti,hwmods = "tpcc"; + reg = <0x49000000 0x10000>; + reg-names = "edma3_cc"; interrupts = <12 13 14>; - #dma-cells = <1>; + interrupt-names = "edma3_ccint", "emda3_mperr", + "edma3_ccerrint"; + dma-requests = <64>; + #dma-cells = <2>; + + ti,tptcs = <&edma_tptc0 7>, <&edma_tptc1 5>, + <&edma_tptc2 3>, <&edma_tptc3 0>; + + ti,edma-memcpy-channels = <20 21>; + }; + + edma_tptc0: tptc@49800000 { + compatible = "ti,edma3-tptc"; + ti,hwmods = "tptc0"; + reg = <0x49800000 0x100000>; + interrupts = <112>; + interrupt-names = "edma3_tcerrint"; + }; + + edma_tptc1: tptc@49900000 { + compatible = "ti,edma3-tptc"; + ti,hwmods = "tptc1"; + reg = <0x49900000 0x100000>; + interrupts = <113>; + interrupt-names = "edma3_tcerrint"; + }; + + edma_tptc2: tptc@49a00000 { + compatible = "ti,edma3-tptc"; + ti,hwmods = "tptc2"; + reg = <0x49a00000 0x100000>; + interrupts = <114>; + interrupt-names = "edma3_tcerrint"; + }; + + edma_tptc3: tptc@49b00000 { + compatible = "ti,edma3-tptc"; + ti,hwmods = "tptc3"; + reg = <0x49b00000 0x100000>; + interrupts = <115>; + interrupt-names = "edma3_tcerrint"; }; /* See TRM "Table 1-318. L4HS Instance Summary" */ diff --git a/arch/arm/boot/dts/dra62x-clocks.dtsi b/arch/arm/boot/dts/dra62x-clocks.dtsi new file mode 100644 index 0000000..6f98dc8 --- /dev/null +++ b/arch/arm/boot/dts/dra62x-clocks.dtsi @@ -0,0 +1,23 @@ +/* + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + */ + +#include "dm814x-clocks.dtsi" + +/* + * Compared to dm814x, dra62x has different shifts and more mux options. + * Please add the extra options for ysclk_14 and 16 if really needed. + */ +&timer1_fck { + clocks = <&sysclk18_ck &aud_clkin0_ck &aud_clkin1_ck + &aud_clkin2_ck &devosc_ck &auxosc_ck &tclkin_ck>; + ti,bit-shift = <4>; +}; + +&timer2_fck { + clocks = <&sysclk18_ck &aud_clkin0_ck &aud_clkin1_ck + &aud_clkin2_ck &devosc_ck &auxosc_ck &tclkin_ck>; + ti,bit-shift = <8>; +}; diff --git a/arch/arm/boot/dts/dra62x-j5eco-evm.dts b/arch/arm/boot/dts/dra62x-j5eco-evm.dts new file mode 100644 index 0000000..7900806 --- /dev/null +++ b/arch/arm/boot/dts/dra62x-j5eco-evm.dts @@ -0,0 +1,80 @@ +/* + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + */ +/dts-v1/; + +#include "dra62x.dtsi" + +/ { + model = "DRA62x J5 Eco EVM"; + compatible = "ti,dra62x-j5eco-evm", "ti,dra62x", "ti,dm8148"; + + memory { + device_type = "memory"; + reg = <0x80000000 0x40000000>; /* 1 GB */ + }; + + /* MIC94060YC6 controlled by SD1_POW pin */ + vmmcsd_fixed: fixedregulator@0 { + compatible = "regulator-fixed"; + regulator-name = "vmmcsd_fixed"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + }; +}; + +&cpsw_emac0 { + phy_id = <&davinci_mdio>, <0>; + phy-mode = "rgmii"; +}; + +&cpsw_emac1 { + phy_id = <&davinci_mdio>, <1>; + phy-mode = "rgmii"; +}; + +&mmc2 { + pinctrl-names = "default"; + pinctrl-0 = <&sd1_pins>; + vmmc-supply = <&vmmcsd_fixed>; + bus-width = <4>; + cd-gpios = <&gpio2 6 GPIO_ACTIVE_LOW>; +}; + +&pincntl { + sd1_pins: pinmux_sd1_pins { + pinctrl-single,pins = < + DM814X_IOPAD(0x0800, PIN_INPUT | 0x1) /* SD1_CLK */ + DM814X_IOPAD(0x0804, PIN_INPUT_PULLUP | 0x1) /* SD1_CMD */ + DM814X_IOPAD(0x0808, PIN_INPUT_PULLUP | 0x1) /* SD1_DAT[0] */ + DM814X_IOPAD(0x080c, PIN_INPUT_PULLUP | 0x1) /* SD1_DAT[1] */ + DM814X_IOPAD(0x0810, PIN_INPUT_PULLUP | 0x1) /* SD1_DAT[2] */ + DM814X_IOPAD(0x0814, PIN_INPUT_PULLUP | 0x1) /* SD1_DAT[3] */ + DM814X_IOPAD(0x0924, PIN_OUTPUT | 0x40) /* SD1_POW */ + DM814X_IOPAD(0x093C, PIN_INPUT_PULLUP | 0x80) /* GP1[6] */ + >; + }; + + usb0_pins: pinmux_usb0_pins { + pinctrl-single,pins = < + DM814X_IOPAD(0x0c34, PIN_OUTPUT | 0x1) /* USB0_DRVVBUS */ + >; + }; +}; + +/* USB0_ID pin state: SW10[1] = 0 cable detection, SW10[1] = 1 ID grounded */ +&usb0 { + pinctrl-names = "default"; + pinctrl-0 = <&usb0_pins>; + dr_mode = "otg"; +}; + +&usb1_phy { + status = "disabled"; +}; + +&usb1 { + status = "disabled"; +}; diff --git a/arch/arm/boot/dts/dra62x.dtsi b/arch/arm/boot/dts/dra62x.dtsi new file mode 100644 index 0000000..d3cbb4e --- /dev/null +++ b/arch/arm/boot/dts/dra62x.dtsi @@ -0,0 +1,23 @@ +/* + * This file is licensed under the terms of the GNU General Public License + * version 2. This program is licensed "as is" without any warranty of any + * kind, whether express or implied. + */ + +#include "dm814x.dtsi" + +/ { + compatible = "ti,dra62x"; +}; + +/* Compared to dm814x, dra62x has different offsets for Ethernet */ +&mac { + reg = <0x4a100000 0x800 + 0x4a101200 0x100>; +}; + +&davinci_mdio { + reg = <0x4a101000 0x100>; +}; + +#include "dra62x-clocks.dtsi" diff --git a/arch/arm/mach-omap2/io.c b/arch/arm/mach-omap2/io.c index 3eaeaca..3c87e40 100644 --- a/arch/arm/mach-omap2/io.c +++ b/arch/arm/mach-omap2/io.c @@ -612,8 +612,7 @@ void __init ti814x_init_early(void) ti814x_clockdomains_init(); dm814x_hwmod_init(); omap_hwmod_init_postsetup(); - if (of_have_populated_dt()) - omap_clk_soc_init = dm814x_dt_clk_init; + omap_clk_soc_init = dm814x_dt_clk_init; } void __init ti816x_init_early(void) diff --git a/arch/arm/mach-omap2/omap_hwmod_81xx_data.c b/arch/arm/mach-omap2/omap_hwmod_81xx_data.c index 6256052..1b96cdf 100644 --- a/arch/arm/mach-omap2/omap_hwmod_81xx_data.c +++ b/arch/arm/mach-omap2/omap_hwmod_81xx_data.c @@ -599,7 +599,7 @@ static struct omap_timer_capability_dev_attr capability_alwon_dev_attr = { static struct omap_hwmod dm814x_timer1_hwmod = { .name = "timer1", .clkdm_name = "alwon_l3s_clkdm", - .main_clk = "timer_sys_ck", + .main_clk = "timer1_fck", .dev_attr = &capability_alwon_dev_attr, .class = &dm816x_timer_hwmod_class, .flags = HWMOD_NO_IDLEST, @@ -608,7 +608,7 @@ static struct omap_hwmod dm814x_timer1_hwmod = { static struct omap_hwmod_ocp_if dm814x_l4_ls__timer1 = { .master = &dm81xx_l4_ls_hwmod, .slave = &dm814x_timer1_hwmod, - .clk = "timer_sys_ck", + .clk = "timer1_fck", .user = OCP_USER_MPU, }; @@ -636,7 +636,7 @@ static struct omap_hwmod_ocp_if dm816x_l4_ls__timer1 = { static struct omap_hwmod dm814x_timer2_hwmod = { .name = "timer2", .clkdm_name = "alwon_l3s_clkdm", - .main_clk = "timer_sys_ck", + .main_clk = "timer2_fck", .dev_attr = &capability_alwon_dev_attr, .class = &dm816x_timer_hwmod_class, .flags = HWMOD_NO_IDLEST, @@ -645,7 +645,7 @@ static struct omap_hwmod dm814x_timer2_hwmod = { static struct omap_hwmod_ocp_if dm814x_l4_ls__timer2 = { .master = &dm81xx_l4_ls_hwmod, .slave = &dm814x_timer2_hwmod, - .clk = "timer_sys_ck", + .clk = "timer2_fck", .user = OCP_USER_MPU, }; @@ -1230,8 +1230,6 @@ static struct omap_hwmod_ocp_if dm81xx_tptc3__alwon_l3_fast = { /* * REVISIT: Test and enable the following once clocks work: - * dm81xx_l4_ls__gpio1 - * dm81xx_l4_ls__gpio2 * dm81xx_l4_ls__mailbox * dm81xx_alwon_l3_slow__gpmc * dm81xx_default_l3_slow__usbss @@ -1250,6 +1248,8 @@ static struct omap_hwmod_ocp_if *dm814x_hwmod_ocp_ifs[] __initdata = { &dm81xx_l4_ls__wd_timer1, &dm81xx_l4_ls__i2c1, &dm81xx_l4_ls__i2c2, + &dm81xx_l4_ls__gpio1, + &dm81xx_l4_ls__gpio2, &dm81xx_l4_ls__elm, &dm81xx_l4_ls__mcspi1, &dm81xx_alwon_l3_fast__tpcc, diff --git a/arch/arm/mach-omap2/prm_common.c b/arch/arm/mach-omap2/prm_common.c index 3fc2cbe..55acc76 100644 --- a/arch/arm/mach-omap2/prm_common.c +++ b/arch/arm/mach-omap2/prm_common.c @@ -662,6 +662,11 @@ static struct omap_prcm_init_data am3_prm_data __initdata = { .index = TI_CLKM_PRM, .init = am33xx_prm_init, }; + +static struct omap_prcm_init_data dm814_pllss_data __initdata = { + .index = TI_CLKM_PLLSS, + .init = am33xx_prm_init, +}; #endif #ifdef CONFIG_ARCH_OMAP4 @@ -715,6 +720,7 @@ static const struct of_device_id const omap_prcm_dt_match_table[] __initconst = #endif #ifdef CONFIG_SOC_TI81XX { .compatible = "ti,dm814-prcm", .data = &am3_prm_data }, + { .compatible = "ti,dm814-pllss", .data = &dm814_pllss_data }, { .compatible = "ti,dm816-prcm", .data = &am3_prm_data }, #endif #ifdef CONFIG_ARCH_OMAP2 |