diff options
Diffstat (limited to 'drivers/media/video/cx18/cx18-dvb.c')
| -rw-r--r-- | drivers/media/video/cx18/cx18-dvb.c | 160 |
1 files changed, 160 insertions, 0 deletions
diff --git a/drivers/media/video/cx18/cx18-dvb.c b/drivers/media/video/cx18/cx18-dvb.c index 6ea3fe6..51a0c33 100644 --- a/drivers/media/video/cx18/cx18-dvb.c +++ b/drivers/media/video/cx18/cx18-dvb.c @@ -30,6 +30,10 @@ #include "s5h1409.h" #include "mxl5005s.h" #include "zl10353.h" + +#include <linux/firmware.h> +#include "mt352.h" +#include "mt352_priv.h" #include "tuner-xc2028.h" DVB_DEFINE_MOD_OPT_ADAPTER_NR(adapter_nr); @@ -38,6 +42,11 @@ DVB_DEFINE_MOD_OPT_ADAPTER_NR(adapter_nr); #define CX18_CLOCK_ENABLE2 0xc71024 #define CX18_DMUX_CLK_MASK 0x0080 +/* + * CX18_CARD_HVR_1600_ESMT + * CX18_CARD_HVR_1600_SAMSUNG + */ + static struct mxl5005s_config hauppauge_hvr1600_tuner = { .i2c_address = 0xC6 >> 1, .if_freq = IF_FREQ_5380000HZ, @@ -65,6 +74,9 @@ static struct s5h1409_config hauppauge_hvr1600_config = { .mpeg_timing = S5H1409_MPEGTIMING_CONTINOUS_NONINVERTING_CLOCK }; +/* + * CX18_CARD_LEADTEK_DVR3100H + */ /* Information/confirmation of proper config values provided by Terry Wu */ static struct zl10353_config leadtek_dvr3100h_demod = { .demod_address = 0x1e >> 1, /* Datasheet suggested straps */ @@ -74,6 +86,121 @@ static struct zl10353_config leadtek_dvr3100h_demod = { .disable_i2c_gate_ctrl = 1, /* Disable the I2C gate */ }; +/* + * CX18_CARD_YUAN_MPC718 + */ +/* + * Due to + * + * 1. an absence of information on how to prgram the MT352 + * 2. the Linux mt352 module pushing MT352 initialzation off onto us here + * + * We have to use an init sequence that *you* must extract from the Windows + * driver (yuanrap.sys) and which we load as a firmware. + * + * If someone can provide me with a Zarlink MT352 (Intel CE6352?) Design Manual + * with chip programming details, then I can remove this annoyance. + */ +static int yuan_mpc718_mt352_reqfw(struct cx18_stream *stream, + const struct firmware **fw) +{ + struct cx18 *cx = stream->cx; + const char *fn = "dvb-cx18-mpc718-mt352.fw"; + int ret; + + ret = request_firmware(fw, fn, &cx->pci_dev->dev); + if (ret) + CX18_ERR("Unable to open firmware file %s\n", fn); + else { + size_t sz = (*fw)->size; + if (sz < 2 || sz > 64 || (sz % 2) != 0) { + CX18_ERR("Firmware %s has a bad size: %lu bytes\n", + fn, (unsigned long) sz); + ret = -EILSEQ; + release_firmware(*fw); + *fw = NULL; + } + } + + if (ret) { + CX18_ERR("The MPC718 board variant with the MT352 DVB-T" + "demodualtor will not work without it\n"); + CX18_ERR("Run 'linux/Documentation/dvb/get_dvb_firmware " + "mpc718' if you need the firmware\n"); + } + return ret; +} + +static int yuan_mpc718_mt352_init(struct dvb_frontend *fe) +{ + struct cx18_dvb *dvb = container_of(fe->dvb, + struct cx18_dvb, dvb_adapter); + struct cx18_stream *stream = container_of(dvb, struct cx18_stream, dvb); + const struct firmware *fw = NULL; + int ret; + int i; + u8 buf[3]; + + ret = yuan_mpc718_mt352_reqfw(stream, &fw); + if (ret) + return ret; + + /* Loop through all the register-value pairs in the firmware file */ + for (i = 0; i < fw->size; i += 2) { + buf[0] = fw->data[i]; + /* Intercept a few registers we want to set ourselves */ + switch (buf[0]) { + case TRL_NOMINAL_RATE_0: + /* Set our custom OFDM bandwidth in the case below */ + break; + case TRL_NOMINAL_RATE_1: + /* 6 MHz: 64/7 * 6/8 / 20.48 * 2^16 = 0x55b6.db6 */ + /* 7 MHz: 64/7 * 7/8 / 20.48 * 2^16 = 0x6400 */ + /* 8 MHz: 64/7 * 8/8 / 20.48 * 2^16 = 0x7249.249 */ + buf[1] = 0x72; + buf[2] = 0x49; + mt352_write(fe, buf, 3); + break; + case INPUT_FREQ_0: + /* Set our custom IF in the case below */ + break; + case INPUT_FREQ_1: + /* 4.56 MHz IF: (20.48 - 4.56)/20.48 * 2^14 = 0x31c0 */ + buf[1] = 0x31; + buf[2] = 0xc0; + mt352_write(fe, buf, 3); + break; + default: + /* Pass through the register-value pair from the fw */ + buf[1] = fw->data[i+1]; + mt352_write(fe, buf, 2); + break; + } + } + + buf[0] = (u8) TUNER_GO; + buf[1] = 0x01; /* Go */ + mt352_write(fe, buf, 2); + release_firmware(fw); + return 0; +} + +static struct mt352_config yuan_mpc718_mt352_demod = { + .demod_address = 0x1e >> 1, + .adc_clock = 20480, /* 20.480 MHz */ + .if2 = 4560, /* 4.560 MHz */ + .no_tuner = 1, /* XC3028 is not behind the gate */ + .demod_init = yuan_mpc718_mt352_init, +}; + +static struct zl10353_config yuan_mpc718_zl10353_demod = { + .demod_address = 0x1e >> 1, /* Datasheet suggested straps */ + .if2 = 45600, /* 4.560 MHz IF from the XC3028 */ + .parallel_ts = 1, /* Not a serial TS */ + .no_tuner = 1, /* XC3028 is not behind the gate */ + .disable_i2c_gate_ctrl = 1, /* Disable the I2C gate */ +}; + static int dvb_register(struct cx18_stream *stream); /* Kernel DVB framework calls this when the feed needs to start. @@ -113,6 +240,7 @@ static int cx18_dvb_start_feed(struct dvb_demux_feed *feed) break; case CX18_CARD_LEADTEK_DVR3100H: + case CX18_CARD_YUAN_MPC718: default: /* Assumption - Parallel transport - Signalling * undefined or default. @@ -326,6 +454,38 @@ static int dvb_register(struct cx18_stream *stream) fe->ops.tuner_ops.set_config(fe, &ctrl); } break; + case CX18_CARD_YUAN_MPC718: + /* + * TODO + * Apparently, these cards also could instead have a + * DiBcom demod supported by one of the db7000 drivers + */ + dvb->fe = dvb_attach(mt352_attach, + &yuan_mpc718_mt352_demod, + &cx->i2c_adap[1]); + if (dvb->fe == NULL) + dvb->fe = dvb_attach(zl10353_attach, + &yuan_mpc718_zl10353_demod, + &cx->i2c_adap[1]); + if (dvb->fe != NULL) { + struct dvb_frontend *fe; + struct xc2028_config cfg = { + .i2c_adap = &cx->i2c_adap[1], + .i2c_addr = 0xc2 >> 1, + .ctrl = NULL, + }; + static struct xc2028_ctrl ctrl = { + .fname = XC2028_DEFAULT_FIRMWARE, + .max_len = 64, + .demod = XC3028_FE_ZARLINK456, + .type = XC2028_AUTO, + }; + + fe = dvb_attach(xc2028_attach, dvb->fe, &cfg); + if (fe != NULL && fe->ops.tuner_ops.set_config != NULL) + fe->ops.tuner_ops.set_config(fe, &ctrl); + } + break; default: /* No Digital Tv Support */ break; |