diff options
Diffstat (limited to 'drivers/mtd/nand/bcm_umi_nand.c')
| -rw-r--r-- | drivers/mtd/nand/bcm_umi_nand.c | 533 |
1 files changed, 0 insertions, 533 deletions
diff --git a/drivers/mtd/nand/bcm_umi_nand.c b/drivers/mtd/nand/bcm_umi_nand.c deleted file mode 100644 index 3fcbcbc..0000000 --- a/drivers/mtd/nand/bcm_umi_nand.c +++ /dev/null @@ -1,533 +0,0 @@ -/***************************************************************************** -* Copyright 2004 - 2009 Broadcom Corporation. All rights reserved. -* -* Unless you and Broadcom execute a separate written software license -* agreement governing use of this software, this software is licensed to you -* under the terms of the GNU General Public License version 2, available at -* http://www.broadcom.com/licenses/GPLv2.php (the "GPL"). -* -* Notwithstanding the above, under no circumstances may you combine this -* software in any way with any other Broadcom software provided under a -* license other than the GPL, without Broadcom's express prior written -* consent. -*****************************************************************************/ - -/* ---- Include Files ---------------------------------------------------- */ -#include <linux/module.h> -#include <linux/types.h> -#include <linux/init.h> -#include <linux/kernel.h> -#include <linux/slab.h> -#include <linux/string.h> -#include <linux/ioport.h> -#include <linux/device.h> -#include <linux/delay.h> -#include <linux/err.h> -#include <linux/io.h> -#include <linux/platform_device.h> -#include <linux/mtd/mtd.h> -#include <linux/mtd/nand.h> -#include <linux/mtd/nand_ecc.h> -#include <linux/mtd/partitions.h> - -#include <asm/mach-types.h> - -#include <mach/reg_nand.h> -#include <mach/reg_umi.h> - -#include "nand_bcm_umi.h" - -#include <mach/memory_settings.h> - -#define USE_DMA 1 -#include <mach/dma.h> -#include <linux/dma-mapping.h> -#include <linux/completion.h> - -/* ---- External Variable Declarations ----------------------------------- */ -/* ---- External Function Prototypes ------------------------------------- */ -/* ---- Public Variables ------------------------------------------------- */ -/* ---- Private Constants and Types -------------------------------------- */ -static const __devinitconst char gBanner[] = KERN_INFO \ - "BCM UMI MTD NAND Driver: 1.00\n"; - -#if NAND_ECC_BCH -static uint8_t scan_ff_pattern[] = { 0xff }; - -static struct nand_bbt_descr largepage_bbt = { - .options = 0, - .offs = 0, - .len = 1, - .pattern = scan_ff_pattern -}; -#endif - -/* -** Preallocate a buffer to avoid having to do this every dma operation. -** This is the size of the preallocated coherent DMA buffer. -*/ -#if USE_DMA -#define DMA_MIN_BUFLEN 512 -#define DMA_MAX_BUFLEN PAGE_SIZE -#define USE_DIRECT_IO(len) (((len) < DMA_MIN_BUFLEN) || \ - ((len) > DMA_MAX_BUFLEN)) - -/* - * The current NAND data space goes from 0x80001900 to 0x80001FFF, - * which is only 0x700 = 1792 bytes long. This is too small for 2K, 4K page - * size NAND flash. Need to break the DMA down to multiple 1Ks. - * - * Need to make sure REG_NAND_DATA_PADDR + DMA_MAX_LEN < 0x80002000 - */ -#define DMA_MAX_LEN 1024 - -#else /* !USE_DMA */ -#define DMA_MIN_BUFLEN 0 -#define DMA_MAX_BUFLEN 0 -#define USE_DIRECT_IO(len) 1 -#endif -/* ---- Private Function Prototypes -------------------------------------- */ -static void bcm_umi_nand_read_buf(struct mtd_info *mtd, u_char * buf, int len); -static void bcm_umi_nand_write_buf(struct mtd_info *mtd, const u_char * buf, - int len); - -/* ---- Private Variables ------------------------------------------------ */ -static struct mtd_info *board_mtd; -static void __iomem *bcm_umi_io_base; -static void *virtPtr; -static dma_addr_t physPtr; -static struct completion nand_comp; - -/* ---- Private Functions ------------------------------------------------ */ -#if NAND_ECC_BCH -#include "bcm_umi_bch.c" -#else -#include "bcm_umi_hamming.c" -#endif - -#if USE_DMA - -/* Handler called when the DMA finishes. */ -static void nand_dma_handler(DMA_Device_t dev, int reason, void *userData) -{ - complete(&nand_comp); -} - -static int nand_dma_init(void) -{ - int rc; - - rc = dma_set_device_handler(DMA_DEVICE_NAND_MEM_TO_MEM, - nand_dma_handler, NULL); - if (rc != 0) { - printk(KERN_ERR "dma_set_device_handler failed: %d\n", rc); - return rc; - } - - virtPtr = - dma_alloc_coherent(NULL, DMA_MAX_BUFLEN, &physPtr, GFP_KERNEL); - if (virtPtr == NULL) { - printk(KERN_ERR "NAND - Failed to allocate memory for DMA buffer\n"); - return -ENOMEM; - } - - return 0; -} - -static void nand_dma_term(void) -{ - if (virtPtr != NULL) - dma_free_coherent(NULL, DMA_MAX_BUFLEN, virtPtr, physPtr); -} - -static void nand_dma_read(void *buf, int len) -{ - int offset = 0; - int tmp_len = 0; - int len_left = len; - DMA_Handle_t hndl; - - if (virtPtr == NULL) - panic("nand_dma_read: virtPtr == NULL\n"); - - if ((void *)physPtr == NULL) - panic("nand_dma_read: physPtr == NULL\n"); - - hndl = dma_request_channel(DMA_DEVICE_NAND_MEM_TO_MEM); - if (hndl < 0) { - printk(KERN_ERR - "nand_dma_read: unable to allocate dma channel: %d\n", - (int)hndl); - panic("\n"); - } - - while (len_left > 0) { - if (len_left > DMA_MAX_LEN) { - tmp_len = DMA_MAX_LEN; - len_left -= DMA_MAX_LEN; - } else { - tmp_len = len_left; - len_left = 0; - } - - init_completion(&nand_comp); - dma_transfer_mem_to_mem(hndl, REG_NAND_DATA_PADDR, - physPtr + offset, tmp_len); - wait_for_completion(&nand_comp); - - offset += tmp_len; - } - - dma_free_channel(hndl); - - if (buf != NULL) - memcpy(buf, virtPtr, len); -} - -static void nand_dma_write(const void *buf, int len) -{ - int offset = 0; - int tmp_len = 0; - int len_left = len; - DMA_Handle_t hndl; - - if (buf == NULL) - panic("nand_dma_write: buf == NULL\n"); - - if (virtPtr == NULL) - panic("nand_dma_write: virtPtr == NULL\n"); - - if ((void *)physPtr == NULL) - panic("nand_dma_write: physPtr == NULL\n"); - - memcpy(virtPtr, buf, len); - - - hndl = dma_request_channel(DMA_DEVICE_NAND_MEM_TO_MEM); - if (hndl < 0) { - printk(KERN_ERR - "nand_dma_write: unable to allocate dma channel: %d\n", - (int)hndl); - panic("\n"); - } - - while (len_left > 0) { - if (len_left > DMA_MAX_LEN) { - tmp_len = DMA_MAX_LEN; - len_left -= DMA_MAX_LEN; - } else { - tmp_len = len_left; - len_left = 0; - } - - init_completion(&nand_comp); - dma_transfer_mem_to_mem(hndl, physPtr + offset, - REG_NAND_DATA_PADDR, tmp_len); - wait_for_completion(&nand_comp); - - offset += tmp_len; - } - - dma_free_channel(hndl); -} - -#endif - -static int nand_dev_ready(struct mtd_info *mtd) -{ - return nand_bcm_umi_dev_ready(); -} - -/**************************************************************************** -* -* bcm_umi_nand_inithw -* -* This routine does the necessary hardware (board-specific) -* initializations. This includes setting up the timings, etc. -* -***************************************************************************/ -int bcm_umi_nand_inithw(void) -{ - /* Configure nand timing parameters */ - REG_UMI_NAND_TCR &= ~0x7ffff; - REG_UMI_NAND_TCR |= HW_CFG_NAND_TCR; - -#if !defined(CONFIG_MTD_NAND_BCM_UMI_HWCS) - /* enable software control of CS */ - REG_UMI_NAND_TCR |= REG_UMI_NAND_TCR_CS_SWCTRL; -#endif - - /* keep NAND chip select asserted */ - REG_UMI_NAND_RCSR |= REG_UMI_NAND_RCSR_CS_ASSERTED; - - REG_UMI_NAND_TCR &= ~REG_UMI_NAND_TCR_WORD16; - /* enable writes to flash */ - REG_UMI_MMD_ICR |= REG_UMI_MMD_ICR_FLASH_WP; - - writel(NAND_CMD_RESET, bcm_umi_io_base + REG_NAND_CMD_OFFSET); - nand_bcm_umi_wait_till_ready(); - -#if NAND_ECC_BCH - nand_bcm_umi_bch_config_ecc(NAND_ECC_NUM_BYTES); -#endif - - return 0; -} - -/* Used to turn latch the proper register for access. */ -static void bcm_umi_nand_hwcontrol(struct mtd_info *mtd, int cmd, - unsigned int ctrl) -{ - /* send command to hardware */ - struct nand_chip *chip = mtd->priv; - if (ctrl & NAND_CTRL_CHANGE) { - if (ctrl & NAND_CLE) { - chip->IO_ADDR_W = bcm_umi_io_base + REG_NAND_CMD_OFFSET; - goto CMD; - } - if (ctrl & NAND_ALE) { - chip->IO_ADDR_W = - bcm_umi_io_base + REG_NAND_ADDR_OFFSET; - goto CMD; - } - chip->IO_ADDR_W = bcm_umi_io_base + REG_NAND_DATA8_OFFSET; - } - -CMD: - /* Send command to chip directly */ - if (cmd != NAND_CMD_NONE) - writeb(cmd, chip->IO_ADDR_W); -} - -static void bcm_umi_nand_write_buf(struct mtd_info *mtd, const u_char * buf, - int len) -{ - if (USE_DIRECT_IO(len)) { - /* Do it the old way if the buffer is small or too large. - * Probably quicker than starting and checking dma. */ - int i; - struct nand_chip *this = mtd->priv; - - for (i = 0; i < len; i++) - writeb(buf[i], this->IO_ADDR_W); - } -#if USE_DMA - else - nand_dma_write(buf, len); -#endif -} - -static void bcm_umi_nand_read_buf(struct mtd_info *mtd, u_char * buf, int len) -{ - if (USE_DIRECT_IO(len)) { - int i; - struct nand_chip *this = mtd->priv; - - for (i = 0; i < len; i++) - buf[i] = readb(this->IO_ADDR_R); - } -#if USE_DMA - else - nand_dma_read(buf, len); -#endif -} - -static int __devinit bcm_umi_nand_probe(struct platform_device *pdev) -{ - struct nand_chip *this; - struct resource *r; - int err = 0; - - printk(gBanner); - - /* Allocate memory for MTD device structure and private data */ - board_mtd = - kmalloc(sizeof(struct mtd_info) + sizeof(struct nand_chip), - GFP_KERNEL); - if (!board_mtd) { - printk(KERN_WARNING - "Unable to allocate NAND MTD device structure.\n"); - return -ENOMEM; - } - - r = platform_get_resource(pdev, IORESOURCE_MEM, 0); - - if (!r) { - err = -ENXIO; - goto out_free; - } - - /* map physical address */ - bcm_umi_io_base = ioremap(r->start, resource_size(r)); - - if (!bcm_umi_io_base) { - printk(KERN_ERR "ioremap to access BCM UMI NAND chip failed\n"); - err = -EIO; - goto out_free; - } - - /* Get pointer to private data */ - this = (struct nand_chip *)(&board_mtd[1]); - - /* Initialize structures */ - memset((char *)board_mtd, 0, sizeof(struct mtd_info)); - memset((char *)this, 0, sizeof(struct nand_chip)); - - /* Link the private data with the MTD structure */ - board_mtd->priv = this; - - /* Initialize the NAND hardware. */ - if (bcm_umi_nand_inithw() < 0) { - printk(KERN_ERR "BCM UMI NAND chip could not be initialized\n"); - err = -EIO; - goto out_unmap; - } - - /* Set address of NAND IO lines */ - this->IO_ADDR_W = bcm_umi_io_base + REG_NAND_DATA8_OFFSET; - this->IO_ADDR_R = bcm_umi_io_base + REG_NAND_DATA8_OFFSET; - - /* Set command delay time, see datasheet for correct value */ - this->chip_delay = 0; - /* Assign the device ready function, if available */ - this->dev_ready = nand_dev_ready; - this->options = 0; - - this->write_buf = bcm_umi_nand_write_buf; - this->read_buf = bcm_umi_nand_read_buf; - - this->cmd_ctrl = bcm_umi_nand_hwcontrol; - this->ecc.mode = NAND_ECC_HW; - this->ecc.size = 512; - this->ecc.bytes = NAND_ECC_NUM_BYTES; -#if NAND_ECC_BCH - this->ecc.read_page = bcm_umi_bch_read_page_hwecc; - this->ecc.write_page = bcm_umi_bch_write_page_hwecc; -#else - this->ecc.correct = nand_correct_data512; - this->ecc.calculate = bcm_umi_hamming_get_hw_ecc; - this->ecc.hwctl = bcm_umi_hamming_enable_hwecc; -#endif - -#if USE_DMA - err = nand_dma_init(); - if (err != 0) - goto out_unmap; -#endif - - /* Figure out the size of the device that we have. - * We need to do this to figure out which ECC - * layout we'll be using. - */ - - err = nand_scan_ident(board_mtd, 1, NULL); - if (err) { - printk(KERN_ERR "nand_scan failed: %d\n", err); - goto out_unmap; - } - - /* Now that we know the nand size, we can setup the ECC layout */ - - switch (board_mtd->writesize) { /* writesize is the pagesize */ - case 4096: - this->ecc.layout = &nand_hw_eccoob_4096; - break; - case 2048: - this->ecc.layout = &nand_hw_eccoob_2048; - break; - case 512: - this->ecc.layout = &nand_hw_eccoob_512; - break; - default: - { - printk(KERN_ERR "NAND - Unrecognized pagesize: %d\n", - board_mtd->writesize); - err = -EINVAL; - goto out_unmap; - } - } - -#if NAND_ECC_BCH - if (board_mtd->writesize > 512) { - if (this->bbt_options & NAND_BBT_USE_FLASH) - largepage_bbt.options = NAND_BBT_SCAN2NDPAGE; - this->badblock_pattern = &largepage_bbt; - } - - this->ecc.strength = 8; - -#endif - - /* Now finish off the scan, now that ecc.layout has been initialized. */ - - err = nand_scan_tail(board_mtd); - if (err) { - printk(KERN_ERR "nand_scan failed: %d\n", err); - goto out_unmap; - } - - /* Register the partitions */ - board_mtd->name = "bcm_umi-nand"; - mtd_device_parse_register(board_mtd, NULL, NULL, NULL, 0); - - /* Return happy */ - return 0; -out_unmap: - iounmap(bcm_umi_io_base); -out_free: - kfree(board_mtd); - return err; -} - -static int bcm_umi_nand_remove(struct platform_device *pdev) -{ -#if USE_DMA - nand_dma_term(); -#endif - - /* Release resources, unregister device */ - nand_release(board_mtd); - - /* unmap physical address */ - iounmap(bcm_umi_io_base); - - /* Free the MTD device structure */ - kfree(board_mtd); - - return 0; -} - -#ifdef CONFIG_PM -static int bcm_umi_nand_suspend(struct platform_device *pdev, - pm_message_t state) -{ - printk(KERN_ERR "MTD NAND suspend is being called\n"); - return 0; -} - -static int bcm_umi_nand_resume(struct platform_device *pdev) -{ - printk(KERN_ERR "MTD NAND resume is being called\n"); - return 0; -} -#else -#define bcm_umi_nand_suspend NULL -#define bcm_umi_nand_resume NULL -#endif - -static struct platform_driver nand_driver = { - .driver = { - .name = "bcm-nand", - .owner = THIS_MODULE, - }, - .probe = bcm_umi_nand_probe, - .remove = bcm_umi_nand_remove, - .suspend = bcm_umi_nand_suspend, - .resume = bcm_umi_nand_resume, -}; - -module_platform_driver(nand_driver); - -MODULE_LICENSE("GPL"); -MODULE_AUTHOR("Broadcom"); -MODULE_DESCRIPTION("BCM UMI MTD NAND driver"); |