summaryrefslogtreecommitdiff
path: root/drivers/net/e1000/e1000_hw.c
diff options
context:
space:
mode:
Diffstat (limited to 'drivers/net/e1000/e1000_hw.c')
-rw-r--r--drivers/net/e1000/e1000_hw.c1987
1 files changed, 1597 insertions, 390 deletions
diff --git a/drivers/net/e1000/e1000_hw.c b/drivers/net/e1000/e1000_hw.c
index 786a9b9..723589b 100644
--- a/drivers/net/e1000/e1000_hw.c
+++ b/drivers/net/e1000/e1000_hw.c
@@ -1,7 +1,7 @@
/*******************************************************************************
- Copyright(c) 1999 - 2004 Intel Corporation. All rights reserved.
+ Copyright(c) 1999 - 2005 Intel Corporation. All rights reserved.
This program is free software; you can redistribute it and/or modify it
under the terms of the GNU General Public License as published by the Free
@@ -63,10 +63,11 @@ static uint16_t e1000_shift_in_ee_bits(struct e1000_hw *hw, uint16_t count);
static int32_t e1000_acquire_eeprom(struct e1000_hw *hw);
static void e1000_release_eeprom(struct e1000_hw *hw);
static void e1000_standby_eeprom(struct e1000_hw *hw);
-static int32_t e1000_id_led_init(struct e1000_hw * hw);
static int32_t e1000_set_vco_speed(struct e1000_hw *hw);
static int32_t e1000_polarity_reversal_workaround(struct e1000_hw *hw);
static int32_t e1000_set_phy_mode(struct e1000_hw *hw);
+static int32_t e1000_host_if_read_cookie(struct e1000_hw *hw, uint8_t *buffer);
+static uint8_t e1000_calculate_mng_checksum(char *buffer, uint32_t length);
/* IGP cable length table */
static const
@@ -80,6 +81,17 @@ uint16_t e1000_igp_cable_length_table[IGP01E1000_AGC_LENGTH_TABLE_SIZE] =
100, 100, 100, 100, 110, 110, 110, 110, 110, 110, 110, 110, 110, 110, 110, 110,
110, 110, 110, 110, 110, 110, 120, 120, 120, 120, 120, 120, 120, 120, 120, 120};
+static const
+uint16_t e1000_igp_2_cable_length_table[IGP02E1000_AGC_LENGTH_TABLE_SIZE] =
+ { 8, 13, 17, 19, 21, 23, 25, 27, 29, 31, 33, 35, 37, 39, 41, 43,
+ 22, 24, 27, 30, 32, 35, 37, 40, 42, 44, 47, 49, 51, 54, 56, 58,
+ 32, 35, 38, 41, 44, 47, 50, 53, 55, 58, 61, 63, 66, 69, 71, 74,
+ 43, 47, 51, 54, 58, 61, 64, 67, 71, 74, 77, 80, 82, 85, 88, 90,
+ 57, 62, 66, 70, 74, 77, 81, 85, 88, 91, 94, 97, 100, 103, 106, 108,
+ 73, 78, 82, 87, 91, 95, 98, 102, 105, 109, 112, 114, 117, 119, 122, 124,
+ 91, 96, 101, 105, 109, 113, 116, 119, 122, 125, 127, 128, 128, 128, 128, 128,
+ 108, 113, 117, 121, 124, 127, 128, 128, 128, 128, 128, 128, 128, 128, 128, 128};
+
/******************************************************************************
* Set the phy type member in the hw struct.
@@ -91,10 +103,14 @@ e1000_set_phy_type(struct e1000_hw *hw)
{
DEBUGFUNC("e1000_set_phy_type");
+ if(hw->mac_type == e1000_undefined)
+ return -E1000_ERR_PHY_TYPE;
+
switch(hw->phy_id) {
case M88E1000_E_PHY_ID:
case M88E1000_I_PHY_ID:
case M88E1011_I_PHY_ID:
+ case M88E1111_I_PHY_ID:
hw->phy_type = e1000_phy_m88;
break;
case IGP01E1000_I_PHY_ID:
@@ -128,7 +144,6 @@ e1000_phy_init_script(struct e1000_hw *hw)
DEBUGFUNC("e1000_phy_init_script");
-
if(hw->phy_init_script) {
msec_delay(20);
@@ -271,6 +286,7 @@ e1000_set_mac_type(struct e1000_hw *hw)
case E1000_DEV_ID_82546GB_FIBER:
case E1000_DEV_ID_82546GB_SERDES:
case E1000_DEV_ID_82546GB_PCIE:
+ case E1000_DEV_ID_82546GB_QUAD_COPPER:
hw->mac_type = e1000_82546_rev_3;
break;
case E1000_DEV_ID_82541EI:
@@ -289,12 +305,19 @@ e1000_set_mac_type(struct e1000_hw *hw)
case E1000_DEV_ID_82547GI:
hw->mac_type = e1000_82547_rev_2;
break;
+ case E1000_DEV_ID_82573E:
+ case E1000_DEV_ID_82573E_IAMT:
+ hw->mac_type = e1000_82573;
+ break;
default:
/* Should never have loaded on this device */
return -E1000_ERR_MAC_TYPE;
}
switch(hw->mac_type) {
+ case e1000_82573:
+ hw->eeprom_semaphore_present = TRUE;
+ /* fall through */
case e1000_82541:
case e1000_82547:
case e1000_82541_rev_2:
@@ -360,6 +383,9 @@ e1000_reset_hw(struct e1000_hw *hw)
uint32_t icr;
uint32_t manc;
uint32_t led_ctrl;
+ uint32_t timeout;
+ uint32_t extcnf_ctrl;
+ int32_t ret_val;
DEBUGFUNC("e1000_reset_hw");
@@ -369,6 +395,15 @@ e1000_reset_hw(struct e1000_hw *hw)
e1000_pci_clear_mwi(hw);
}
+ if(hw->bus_type == e1000_bus_type_pci_express) {
+ /* Prevent the PCI-E bus from sticking if there is no TLP connection
+ * on the last TLP read/write transaction when MAC is reset.
+ */
+ if(e1000_disable_pciex_master(hw) != E1000_SUCCESS) {
+ DEBUGOUT("PCI-E Master disable polling has failed.\n");
+ }
+ }
+
/* Clear interrupt mask to stop board from generating interrupts */
DEBUGOUT("Masking off all interrupts\n");
E1000_WRITE_REG(hw, IMC, 0xffffffff);
@@ -393,10 +428,32 @@ e1000_reset_hw(struct e1000_hw *hw)
/* Must reset the PHY before resetting the MAC */
if((hw->mac_type == e1000_82541) || (hw->mac_type == e1000_82547)) {
- E1000_WRITE_REG_IO(hw, CTRL, (ctrl | E1000_CTRL_PHY_RST));
+ E1000_WRITE_REG(hw, CTRL, (ctrl | E1000_CTRL_PHY_RST));
msec_delay(5);
}
+ /* Must acquire the MDIO ownership before MAC reset.
+ * Ownership defaults to firmware after a reset. */
+ if(hw->mac_type == e1000_82573) {
+ timeout = 10;
+
+ extcnf_ctrl = E1000_READ_REG(hw, EXTCNF_CTRL);
+ extcnf_ctrl |= E1000_EXTCNF_CTRL_MDIO_SW_OWNERSHIP;
+
+ do {
+ E1000_WRITE_REG(hw, EXTCNF_CTRL, extcnf_ctrl);
+ extcnf_ctrl = E1000_READ_REG(hw, EXTCNF_CTRL);
+
+ if(extcnf_ctrl & E1000_EXTCNF_CTRL_MDIO_SW_OWNERSHIP)
+ break;
+ else
+ extcnf_ctrl |= E1000_EXTCNF_CTRL_MDIO_SW_OWNERSHIP;
+
+ msec_delay(2);
+ timeout--;
+ } while(timeout);
+ }
+
/* Issue a global reset to the MAC. This will reset the chip's
* transmit, receive, DMA, and link units. It will not effect
* the current PCI configuration. The global reset bit is self-
@@ -450,6 +507,18 @@ e1000_reset_hw(struct e1000_hw *hw)
/* Wait for EEPROM reload */
msec_delay(20);
break;
+ case e1000_82573:
+ udelay(10);
+ ctrl_ext = E1000_READ_REG(hw, CTRL_EXT);
+ ctrl_ext |= E1000_CTRL_EXT_EE_RST;
+ E1000_WRITE_REG(hw, CTRL_EXT, ctrl_ext);
+ E1000_WRITE_FLUSH(hw);
+ /* fall through */
+ ret_val = e1000_get_auto_rd_done(hw);
+ if(ret_val)
+ /* We don't want to continue accessing MAC registers. */
+ return ret_val;
+ break;
default:
/* Wait for EEPROM reload (it happens automatically) */
msec_delay(5);
@@ -457,7 +526,7 @@ e1000_reset_hw(struct e1000_hw *hw)
}
/* Disable HW ARPs on ASF enabled adapters */
- if(hw->mac_type >= e1000_82540) {
+ if(hw->mac_type >= e1000_82540 && hw->mac_type <= e1000_82547_rev_2) {
manc = E1000_READ_REG(hw, MANC);
manc &= ~(E1000_MANC_ARP_EN);
E1000_WRITE_REG(hw, MANC, manc);
@@ -510,6 +579,8 @@ e1000_init_hw(struct e1000_hw *hw)
uint16_t pcix_stat_hi_word;
uint16_t cmd_mmrbc;
uint16_t stat_mmrbc;
+ uint32_t mta_size;
+
DEBUGFUNC("e1000_init_hw");
/* Initialize Identification LED */
@@ -524,8 +595,8 @@ e1000_init_hw(struct e1000_hw *hw)
/* Disabling VLAN filtering. */
DEBUGOUT("Initializing the IEEE VLAN\n");
- E1000_WRITE_REG(hw, VET, 0);
-
+ if (hw->mac_type < e1000_82545_rev_3)
+ E1000_WRITE_REG(hw, VET, 0);
e1000_clear_vfta(hw);
/* For 82542 (rev 2.0), disable MWI and put the receiver into reset */
@@ -553,14 +624,16 @@ e1000_init_hw(struct e1000_hw *hw)
/* Zero out the Multicast HASH table */
DEBUGOUT("Zeroing the MTA\n");
- for(i = 0; i < E1000_MC_TBL_SIZE; i++)
+ mta_size = E1000_MC_TBL_SIZE;
+ for(i = 0; i < mta_size; i++)
E1000_WRITE_REG_ARRAY(hw, MTA, i, 0);
/* Set the PCI priority bit correctly in the CTRL register. This
* determines if the adapter gives priority to receives, or if it
- * gives equal priority to transmits and receives.
+ * gives equal priority to transmits and receives. Valid only on
+ * 82542 and 82543 silicon.
*/
- if(hw->dma_fairness) {
+ if(hw->dma_fairness && hw->mac_type <= e1000_82543) {
ctrl = E1000_READ_REG(hw, CTRL);
E1000_WRITE_REG(hw, CTRL, ctrl | E1000_CTRL_PRIOR);
}
@@ -598,9 +671,21 @@ e1000_init_hw(struct e1000_hw *hw)
if(hw->mac_type > e1000_82544) {
ctrl = E1000_READ_REG(hw, TXDCTL);
ctrl = (ctrl & ~E1000_TXDCTL_WTHRESH) | E1000_TXDCTL_FULL_TX_DESC_WB;
+ switch (hw->mac_type) {
+ default:
+ break;
+ case e1000_82573:
+ ctrl |= E1000_TXDCTL_COUNT_DESC;
+ break;
+ }
E1000_WRITE_REG(hw, TXDCTL, ctrl);
}
+ if (hw->mac_type == e1000_82573) {
+ e1000_enable_tx_pkt_filtering(hw);
+ }
+
+
/* Clear all of the statistics registers (clear on read). It is
* important that we do this after we have tried to establish link
* because the symbol error count will increment wildly if there
@@ -679,7 +764,7 @@ e1000_setup_link(struct e1000_hw *hw)
* control setting, then the variable hw->fc will
* be initialized based on a value in the EEPROM.
*/
- if(e1000_read_eeprom(hw, EEPROM_INIT_CONTROL2_REG, 1, &eeprom_data) < 0) {
+ if(e1000_read_eeprom(hw, EEPROM_INIT_CONTROL2_REG, 1, &eeprom_data)) {
DEBUGOUT("EEPROM Read Error\n");
return -E1000_ERR_EEPROM;
}
@@ -736,6 +821,7 @@ e1000_setup_link(struct e1000_hw *hw)
E1000_WRITE_REG(hw, FCAL, FLOW_CONTROL_ADDRESS_LOW);
E1000_WRITE_REG(hw, FCAH, FLOW_CONTROL_ADDRESS_HIGH);
E1000_WRITE_REG(hw, FCT, FLOW_CONTROL_TYPE);
+
E1000_WRITE_REG(hw, FCTTV, hw->fc_pause_time);
/* Set the flow control receive threshold registers. Normally,
@@ -906,20 +992,18 @@ e1000_setup_fiber_serdes_link(struct e1000_hw *hw)
}
/******************************************************************************
-* Detects which PHY is present and the speed and duplex
+* Make sure we have a valid PHY and change PHY mode before link setup.
*
* hw - Struct containing variables accessed by shared code
******************************************************************************/
static int32_t
-e1000_setup_copper_link(struct e1000_hw *hw)
+e1000_copper_link_preconfig(struct e1000_hw *hw)
{
uint32_t ctrl;
- uint32_t led_ctrl;
int32_t ret_val;
- uint16_t i;
uint16_t phy_data;
- DEBUGFUNC("e1000_setup_copper_link");
+ DEBUGFUNC("e1000_copper_link_preconfig");
ctrl = E1000_READ_REG(hw, CTRL);
/* With 82543, we need to force speed and duplex on the MAC equal to what
@@ -933,7 +1017,9 @@ e1000_setup_copper_link(struct e1000_hw *hw)
} else {
ctrl |= (E1000_CTRL_FRCSPD | E1000_CTRL_FRCDPX | E1000_CTRL_SLU);
E1000_WRITE_REG(hw, CTRL, ctrl);
- e1000_phy_hw_reset(hw);
+ ret_val = e1000_phy_hw_reset(hw);
+ if(ret_val)
+ return ret_val;
}
/* Make sure we have a valid PHY */
@@ -961,274 +1047,398 @@ e1000_setup_copper_link(struct e1000_hw *hw)
hw->mac_type == e1000_82541_rev_2 || hw->mac_type == e1000_82547_rev_2)
hw->phy_reset_disable = FALSE;
- if(!hw->phy_reset_disable) {
- if (hw->phy_type == e1000_phy_igp) {
+ return E1000_SUCCESS;
+}
- ret_val = e1000_phy_reset(hw);
- if(ret_val) {
- DEBUGOUT("Error Resetting the PHY\n");
- return ret_val;
- }
- /* Wait 10ms for MAC to configure PHY from eeprom settings */
- msec_delay(15);
+/********************************************************************
+* Copper link setup for e1000_phy_igp series.
+*
+* hw - Struct containing variables accessed by shared code
+*********************************************************************/
+static int32_t
+e1000_copper_link_igp_setup(struct e1000_hw *hw)
+{
+ uint32_t led_ctrl;
+ int32_t ret_val;
+ uint16_t phy_data;
- /* Configure activity LED after PHY reset */
- led_ctrl = E1000_READ_REG(hw, LEDCTL);
- led_ctrl &= IGP_ACTIVITY_LED_MASK;
- led_ctrl |= (IGP_ACTIVITY_LED_ENABLE | IGP_LED3_MODE);
- E1000_WRITE_REG(hw, LEDCTL, led_ctrl);
+ DEBUGFUNC("e1000_copper_link_igp_setup");
- /* disable lplu d3 during driver init */
- ret_val = e1000_set_d3_lplu_state(hw, FALSE);
- if(ret_val) {
- DEBUGOUT("Error Disabling LPLU D3\n");
- return ret_val;
- }
+ if (hw->phy_reset_disable)
+ return E1000_SUCCESS;
+
+ ret_val = e1000_phy_reset(hw);
+ if (ret_val) {
+ DEBUGOUT("Error Resetting the PHY\n");
+ return ret_val;
+ }
- /* Configure mdi-mdix settings */
- ret_val = e1000_read_phy_reg(hw, IGP01E1000_PHY_PORT_CTRL,
- &phy_data);
- if(ret_val)
- return ret_val;
+ /* Wait 10ms for MAC to configure PHY from eeprom settings */
+ msec_delay(15);
- if((hw->mac_type == e1000_82541) || (hw->mac_type == e1000_82547)) {
- hw->dsp_config_state = e1000_dsp_config_disabled;
- /* Force MDI for earlier revs of the IGP PHY */
- phy_data &= ~(IGP01E1000_PSCR_AUTO_MDIX |
- IGP01E1000_PSCR_FORCE_MDI_MDIX);
- hw->mdix = 1;
+ /* Configure activity LED after PHY reset */
+ led_ctrl = E1000_READ_REG(hw, LEDCTL);
+ led_ctrl &= IGP_ACTIVITY_LED_MASK;
+ led_ctrl |= (IGP_ACTIVITY_LED_ENABLE | IGP_LED3_MODE);
+ E1000_WRITE_REG(hw, LEDCTL, led_ctrl);
- } else {
- hw->dsp_config_state = e1000_dsp_config_enabled;
- phy_data &= ~IGP01E1000_PSCR_AUTO_MDIX;
-
- switch (hw->mdix) {
- case 1:
- phy_data &= ~IGP01E1000_PSCR_FORCE_MDI_MDIX;
- break;
- case 2:
- phy_data |= IGP01E1000_PSCR_FORCE_MDI_MDIX;
- break;
- case 0:
- default:
- phy_data |= IGP01E1000_PSCR_AUTO_MDIX;
- break;
- }
- }
- ret_val = e1000_write_phy_reg(hw, IGP01E1000_PHY_PORT_CTRL,
- phy_data);
- if(ret_val)
- return ret_val;
+ /* disable lplu d3 during driver init */
+ ret_val = e1000_set_d3_lplu_state(hw, FALSE);
+ if (ret_val) {
+ DEBUGOUT("Error Disabling LPLU D3\n");
+ return ret_val;
+ }
- /* set auto-master slave resolution settings */
- if(hw->autoneg) {
- e1000_ms_type phy_ms_setting = hw->master_slave;
+ /* disable lplu d0 during driver init */
+ ret_val = e1000_set_d0_lplu_state(hw, FALSE);
+ if (ret_val) {
+ DEBUGOUT("Error Disabling LPLU D0\n");
+ return ret_val;
+ }
+ /* Configure mdi-mdix settings */
+ ret_val = e1000_read_phy_reg(hw, IGP01E1000_PHY_PORT_CTRL, &phy_data);
+ if (ret_val)
+ return ret_val;
- if(hw->ffe_config_state == e1000_ffe_config_active)
- hw->ffe_config_state = e1000_ffe_config_enabled;
+ if ((hw->mac_type == e1000_82541) || (hw->mac_type == e1000_82547)) {
+ hw->dsp_config_state = e1000_dsp_config_disabled;
+ /* Force MDI for earlier revs of the IGP PHY */
+ phy_data &= ~(IGP01E1000_PSCR_AUTO_MDIX | IGP01E1000_PSCR_FORCE_MDI_MDIX);
+ hw->mdix = 1;
- if(hw->dsp_config_state == e1000_dsp_config_activated)
- hw->dsp_config_state = e1000_dsp_config_enabled;
+ } else {
+ hw->dsp_config_state = e1000_dsp_config_enabled;
+ phy_data &= ~IGP01E1000_PSCR_AUTO_MDIX;
- /* when autonegotiation advertisment is only 1000Mbps then we
- * should disable SmartSpeed and enable Auto MasterSlave
- * resolution as hardware default. */
- if(hw->autoneg_advertised == ADVERTISE_1000_FULL) {
- /* Disable SmartSpeed */
- ret_val = e1000_read_phy_reg(hw, IGP01E1000_PHY_PORT_CONFIG,
- &phy_data);
- if(ret_val)
- return ret_val;
- phy_data &= ~IGP01E1000_PSCFR_SMART_SPEED;
- ret_val = e1000_write_phy_reg(hw,
- IGP01E1000_PHY_PORT_CONFIG,
- phy_data);
- if(ret_val)
- return ret_val;
- /* Set auto Master/Slave resolution process */
- ret_val = e1000_read_phy_reg(hw, PHY_1000T_CTRL, &phy_data);
- if(ret_val)
- return ret_val;
- phy_data &= ~CR_1000T_MS_ENABLE;
- ret_val = e1000_write_phy_reg(hw, PHY_1000T_CTRL, phy_data);
- if(ret_val)
- return ret_val;
- }
+ switch (hw->mdix) {
+ case 1:
+ phy_data &= ~IGP01E1000_PSCR_FORCE_MDI_MDIX;
+ break;
+ case 2:
+ phy_data |= IGP01E1000_PSCR_FORCE_MDI_MDIX;
+ break;
+ case 0:
+ default:
+ phy_data |= IGP01E1000_PSCR_AUTO_MDIX;
+ break;
+ }
+ }
+ ret_val = e1000_write_phy_reg(hw, IGP01E1000_PHY_PORT_CTRL, phy_data);
+ if(ret_val)
+ return ret_val;
- ret_val = e1000_read_phy_reg(hw, PHY_1000T_CTRL, &phy_data);
- if(ret_val)
- return ret_val;
+ /* set auto-master slave resolution settings */
+ if(hw->autoneg) {
+ e1000_ms_type phy_ms_setting = hw->master_slave;
- /* load defaults for future use */
- hw->original_master_slave = (phy_data & CR_1000T_MS_ENABLE) ?
- ((phy_data & CR_1000T_MS_VALUE) ?
- e1000_ms_force_master :
- e1000_ms_force_slave) :
- e1000_ms_auto;
-
- switch (phy_ms_setting) {
- case e1000_ms_force_master:
- phy_data |= (CR_1000T_MS_ENABLE | CR_1000T_MS_VALUE);
- break;
- case e1000_ms_force_slave:
- phy_data |= CR_1000T_MS_ENABLE;
- phy_data &= ~(CR_1000T_MS_VALUE);
- break;
- case e1000_ms_auto:
- phy_data &= ~CR_1000T_MS_ENABLE;
- default:
- break;
- }
- ret_val = e1000_write_phy_reg(hw, PHY_1000T_CTRL, phy_data);
- if(ret_val)
- return ret_val;
- }
- } else {
- /* Enable CRS on TX. This must be set for half-duplex operation. */
- ret_val = e1000_read_phy_reg(hw, M88E1000_PHY_SPEC_CTRL,
- &phy_data);
+ if(hw->ffe_config_state == e1000_ffe_config_active)
+ hw->ffe_config_state = e1000_ffe_config_enabled;
+
+ if(hw->dsp_config_state == e1000_dsp_config_activated)
+ hw->dsp_config_state = e1000_dsp_config_enabled;
+
+ /* when autonegotiation advertisment is only 1000Mbps then we
+ * should disable SmartSpeed and enable Auto MasterSlave
+ * resolution as hardware default. */
+ if(hw->autoneg_advertised == ADVERTISE_1000_FULL) {
+ /* Disable SmartSpeed */
+ ret_val = e1000_read_phy_reg(hw, IGP01E1000_PHY_PORT_CONFIG, &phy_data);
+ if(ret_val)
+ return ret_val;
+ phy_data &= ~IGP01E1000_PSCFR_SMART_SPEED;
+ ret_val = e1000_write_phy_reg(hw,
+ IGP01E1000_PHY_PORT_CONFIG,
+ phy_data);
+ if(ret_val)
+ return ret_val;
+ /* Set auto Master/Slave resolution process */
+ ret_val = e1000_read_phy_reg(hw, PHY_1000T_CTRL, &phy_data);
+ if(ret_val)
+ return ret_val;
+ phy_data &= ~CR_1000T_MS_ENABLE;
+ ret_val = e1000_write_phy_reg(hw, PHY_1000T_CTRL, phy_data);
if(ret_val)
return ret_val;
+ }
- phy_data |= M88E1000_PSCR_ASSERT_CRS_ON_TX;
+ ret_val = e1000_read_phy_reg(hw, PHY_1000T_CTRL, &phy_data);
+ if(ret_val)
+ return ret_val;
- /* Options:
- * MDI/MDI-X = 0 (default)
- * 0 - Auto for all speeds
- * 1 - MDI mode
- * 2 - MDI-X mode
- * 3 - Auto for 1000Base-T only (MDI-X for 10/100Base-T modes)
- */
- phy_data &= ~M88E1000_PSCR_AUTO_X_MODE;
+ /* load defaults for future use */
+ hw->original_master_slave = (phy_data & CR_1000T_MS_ENABLE) ?
+ ((phy_data & CR_1000T_MS_VALUE) ?
+ e1000_ms_force_master :
+ e1000_ms_force_slave) :
+ e1000_ms_auto;
- switch (hw->mdix) {
- case 1:
- phy_data |= M88E1000_PSCR_MDI_MANUAL_MODE;
- break;
- case 2:
- phy_data |= M88E1000_PSCR_MDIX_MANUAL_MODE;
- break;
- case 3:
- phy_data |= M88E1000_PSCR_AUTO_X_1000T;
- break;
- case 0:
+ switch (phy_ms_setting) {
+ case e1000_ms_force_master:
+ phy_data |= (CR_1000T_MS_ENABLE | CR_1000T_MS_VALUE);
+ break;
+ case e1000_ms_force_slave:
+ phy_data |= CR_1000T_MS_ENABLE;
+ phy_data &= ~(CR_1000T_MS_VALUE);
+ break;
+ case e1000_ms_auto:
+ phy_data &= ~CR_1000T_MS_ENABLE;
default:
- phy_data |= M88E1000_PSCR_AUTO_X_MODE;
- break;
- }
+ break;
+ }
+ ret_val = e1000_write_phy_reg(hw, PHY_1000T_CTRL, phy_data);
+ if(ret_val)
+ return ret_val;
+ }
- /* Options:
- * disable_polarity_correction = 0 (default)
- * Automatic Correction for Reversed Cable Polarity
- * 0 - Disabled
- * 1 - Enabled
- */
- phy_data &= ~M88E1000_PSCR_POLARITY_REVERSAL;
- if(hw->disable_polarity_correction == 1)
- phy_data |= M88E1000_PSCR_POLARITY_REVERSAL;
- ret_val = e1000_write_phy_reg(hw, M88E1000_PHY_SPEC_CTRL,
- phy_data);
- if(ret_val)
- return ret_val;
+ return E1000_SUCCESS;
+}
- /* Force TX_CLK in the Extended PHY Specific Control Register
- * to 25MHz clock.
- */
- ret_val = e1000_read_phy_reg(hw, M88E1000_EXT_PHY_SPEC_CTRL,
- &phy_data);
- if(ret_val)
- return ret_val;
- phy_data |= M88E1000_EPSCR_TX_CLK_25;
+/********************************************************************
+* Copper link setup for e1000_phy_m88 series.
+*
+* hw - Struct containing variables accessed by shared code
+*********************************************************************/
+static int32_t
+e1000_copper_link_mgp_setup(struct e1000_hw *hw)
+{
+ int32_t ret_val;
+ uint16_t phy_data;
+
+ DEBUGFUNC("e1000_copper_link_mgp_setup");
+
+ if(hw->phy_reset_disable)
+ return E1000_SUCCESS;
+
+ /* Enable CRS on TX. This must be set for half-duplex operation. */
+ ret_val = e1000_read_phy_reg(hw, M88E1000_PHY_SPEC_CTRL, &phy_data);
+ if(ret_val)
+ return ret_val;
+
+ phy_data |= M88E1000_PSCR_ASSERT_CRS_ON_TX;
+
+ /* Options:
+ * MDI/MDI-X = 0 (default)
+ * 0 - Auto for all speeds
+ * 1 - MDI mode
+ * 2 - MDI-X mode
+ * 3 - Auto for 1000Base-T only (MDI-X for 10/100Base-T modes)
+ */
+ phy_data &= ~M88E1000_PSCR_AUTO_X_MODE;
+
+ switch (hw->mdix) {
+ case 1:
+ phy_data |= M88E1000_PSCR_MDI_MANUAL_MODE;
+ break;
+ case 2:
+ phy_data |= M88E1000_PSCR_MDIX_MANUAL_MODE;
+ break;
+ case 3:
+ phy_data |= M88E1000_PSCR_AUTO_X_1000T;
+ break;
+ case 0:
+ default:
+ phy_data |= M88E1000_PSCR_AUTO_X_MODE;
+ break;
+ }
+
+ /* Options:
+ * disable_polarity_correction = 0 (default)
+ * Automatic Correction for Reversed Cable Polarity
+ * 0 - Disabled
+ * 1 - Enabled
+ */
+ phy_data &= ~M88E1000_PSCR_POLARITY_REVERSAL;
+ if(hw->disable_polarity_correction == 1)
+ phy_data |= M88E1000_PSCR_POLARITY_REVERSAL;
+ ret_val = e1000_write_phy_reg(hw, M88E1000_PHY_SPEC_CTRL, phy_data);
+ if(ret_val)
+ return ret_val;
- if (hw->phy_revision < M88E1011_I_REV_4) {
- /* Configure Master and Slave downshift values */
- phy_data &= ~(M88E1000_EPSCR_MASTER_DOWNSHIFT_MASK |
+ /* Force TX_CLK in the Extended PHY Specific Control Register
+ * to 25MHz clock.
+ */
+ ret_val = e1000_read_phy_reg(hw, M88E1000_EXT_PHY_SPEC_CTRL, &phy_data);
+ if(ret_val)
+ return ret_val;
+
+ phy_data |= M88E1000_EPSCR_TX_CLK_25;
+
+ if (hw->phy_revision < M88E1011_I_REV_4) {
+ /* Configure Master and Slave downshift values */
+ phy_data &= ~(M88E1000_EPSCR_MASTER_DOWNSHIFT_MASK |
M88E1000_EPSCR_SLAVE_DOWNSHIFT_MASK);
- phy_data |= (M88E1000_EPSCR_MASTER_DOWNSHIFT_1X |
+ phy_data |= (M88E1000_EPSCR_MASTER_DOWNSHIFT_1X |
M88E1000_EPSCR_SLAVE_DOWNSHIFT_1X);
- ret_val = e1000_write_phy_reg(hw, M88E1000_EXT_PHY_SPEC_CTRL,
- phy_data);
- if(ret_val)
- return ret_val;
- }
+ ret_val = e1000_write_phy_reg(hw, M88E1000_EXT_PHY_SPEC_CTRL, phy_data);
+ if(ret_val)
+ return ret_val;
+ }
- /* SW Reset the PHY so all changes take effect */
- ret_val = e1000_phy_reset(hw);
- if(ret_val) {
- DEBUGOUT("Error Resetting the PHY\n");
- return ret_val;
- }
+ /* SW Reset the PHY so all changes take effect */
+ ret_val = e1000_phy_reset(hw);
+ if(ret_val) {
+ DEBUGOUT("Error Resetting the PHY\n");
+ return ret_val;
+ }
+
+ return E1000_SUCCESS;
+}
+
+/********************************************************************
+* Setup auto-negotiation and flow control advertisements,
+* and then perform auto-negotiation.
+*
+* hw - Struct containing variables accessed by shared code
+*********************************************************************/
+static int32_t
+e1000_copper_link_autoneg(struct e1000_hw *hw)
+{
+ int32_t ret_val;
+ uint16_t phy_data;
+
+ DEBUGFUNC("e1000_copper_link_autoneg");
+
+ /* Perform some bounds checking on the hw->autoneg_advertised
+ * parameter. If this variable is zero, then set it to the default.
+ */
+ hw->autoneg_advertised &= AUTONEG_ADVERTISE_SPEED_DEFAULT;
+
+ /* If autoneg_advertised is zero, we assume it was not defaulted
+ * by the calling code so we set to advertise full capability.
+ */
+ if(hw->autoneg_advertised == 0)
+ hw->autoneg_advertised = AUTONEG_ADVERTISE_SPEED_DEFAULT;
+
+ DEBUGOUT("Reconfiguring auto-neg advertisement params\n");
+ ret_val = e1000_phy_setup_autoneg(hw);
+ if(ret_val) {
+ DEBUGOUT("Error Setting up Auto-Negotiation\n");
+ return ret_val;
+ }
+ DEBUGOUT("Restarting Auto-Neg\n");
+
+ /* Restart auto-negotiation by setting the Auto Neg Enable bit and
+ * the Auto Neg Restart bit in the PHY control register.
+ */
+ ret_val = e1000_read_phy_reg(hw, PHY_CTRL, &phy_data);
+ if(ret_val)
+ return ret_val;
+
+ phy_data |= (MII_CR_AUTO_NEG_EN | MII_CR_RESTART_AUTO_NEG);
+ ret_val = e1000_write_phy_reg(hw, PHY_CTRL, phy_data);
+ if(ret_val)
+ return ret_val;
+
+ /* Does the user want to wait for Auto-Neg to complete here, or
+ * check at a later time (for example, callback routine).
+ */
+ if(hw->wait_autoneg_complete) {
+ ret_val = e1000_wait_autoneg(hw);
+ if(ret_val) {
+ DEBUGOUT("Error while waiting for autoneg to complete\n");
+ return ret_val;
}
+ }
- /* Options:
- * autoneg = 1 (default)
- * PHY will advertise value(s) parsed from
- * autoneg_advertised and fc
- * autoneg = 0
- * PHY will be set to 10H, 10F, 100H, or 100F
- * depending on value parsed from forced_speed_duplex.
- */
+ hw->get_link_status = TRUE;
- /* Is autoneg enabled? This is enabled by default or by software
- * override. If so, call e1000_phy_setup_autoneg routine to parse the
- * autoneg_advertised and fc options. If autoneg is NOT enabled, then
- * the user should have provided a speed/duplex override. If so, then
- * call e1000_phy_force_speed_duplex to parse and set this up.
- */
- if(hw->autoneg) {
- /* Perform some bounds checking on the hw->autoneg_advertised
- * parameter. If this variable is zero, then set it to the default.
- */
- hw->autoneg_advertised &= AUTONEG_ADVERTISE_SPEED_DEFAULT;
+ return E1000_SUCCESS;
+}
- /* If autoneg_advertised is zero, we assume it was not defaulted
- * by the calling code so we set to advertise full capability.
- */
- if(hw->autoneg_advertised == 0)
- hw->autoneg_advertised = AUTONEG_ADVERTISE_SPEED_DEFAULT;
- DEBUGOUT("Reconfiguring auto-neg advertisement params\n");
- ret_val = e1000_phy_setup_autoneg(hw);
- if(ret_val) {
- DEBUGOUT("Error Setting up Auto-Negotiation\n");
- return ret_val;
- }
- DEBUGOUT("Restarting Auto-Neg\n");
+/******************************************************************************
+* Config the MAC and the PHY after link is up.
+* 1) Set up the MAC to the current PHY speed/duplex
+* if we are on 82543. If we
+* are on newer silicon, we only need to configure
+* collision distance in the Transmit Control Register.
+* 2) Set up flow control on the MAC to that established with
+* the link partner.
+* 3) Config DSP to improve Gigabit link quality for some PHY revisions.
+*
+* hw - Struct containing variables accessed by shared code
+******************************************************************************/
+static int32_t
+e1000_copper_link_postconfig(struct e1000_hw *hw)
+{
+ int32_t ret_val;
+ DEBUGFUNC("e1000_copper_link_postconfig");
+
+ if(hw->mac_type >= e1000_82544) {
+ e1000_config_collision_dist(hw);
+ } else {
+ ret_val = e1000_config_mac_to_phy(hw);
+ if(ret_val) {
+ DEBUGOUT("Error configuring MAC to PHY settings\n");
+ return ret_val;
+ }
+ }
+ ret_val = e1000_config_fc_after_link_up(hw);
+ if(ret_val) {
+ DEBUGOUT("Error Configuring Flow Control\n");
+ return ret_val;
+ }
- /* Restart auto-negotiation by setting the Auto Neg Enable bit and
- * the Auto Neg Restart bit in the PHY control register.
- */
- ret_val = e1000_read_phy_reg(hw, PHY_CTRL, &phy_data);
- if(ret_val)
- return ret_val;
+ /* Config DSP to improve Giga link quality */
+ if(hw->phy_type == e1000_phy_igp) {
+ ret_val = e1000_config_dsp_after_link_change(hw, TRUE);
+ if(ret_val) {
+ DEBUGOUT("Error Configuring DSP after link up\n");
+ return ret_val;
+ }
+ }
+
+ return E1000_SUCCESS;
+}
- phy_data |= (MII_CR_AUTO_NEG_EN | MII_CR_RESTART_AUTO_NEG);
- ret_val = e1000_write_phy_reg(hw, PHY_CTRL, phy_data);
- if(ret_val)
- return ret_val;
+/******************************************************************************
+* Detects which PHY is present and setup the speed and duplex
+*
+* hw - Struct containing variables accessed by shared code
+******************************************************************************/
+static int32_t
+e1000_setup_copper_link(struct e1000_hw *hw)
+{
+ int32_t ret_val;
+ uint16_t i;
+ uint16_t phy_data;
- /* Does the user want to wait for Auto-Neg to complete here, or
- * check at a later time (for example, callback routine).
- */
- if(hw->wait_autoneg_complete) {
- ret_val = e1000_wait_autoneg(hw);
- if(ret_val) {
- DEBUGOUT("Error while waiting for autoneg to complete\n");
- return ret_val;
- }
- }
- hw->get_link_status = TRUE;
- } else {
- DEBUGOUT("Forcing speed and duplex\n");
- ret_val = e1000_phy_force_speed_duplex(hw);
- if(ret_val) {
- DEBUGOUT("Error Forcing Speed and Duplex\n");
- return ret_val;
- }
+ DEBUGFUNC("e1000_setup_copper_link");
+
+ /* Check if it is a valid PHY and set PHY mode if necessary. */
+ ret_val = e1000_copper_link_preconfig(hw);
+ if(ret_val)
+ return ret_val;
+
+ if (hw->phy_type == e1000_phy_igp ||
+ hw->phy_type == e1000_phy_igp_2) {
+ ret_val = e1000_copper_link_igp_setup(hw);
+ if(ret_val)
+ return ret_val;
+ } else if (hw->phy_type == e1000_phy_m88) {
+ ret_val = e1000_copper_link_mgp_setup(hw);
+ if(ret_val)
+ return ret_val;
+ }
+
+ if(hw->autoneg) {
+ /* Setup autoneg and flow control advertisement
+ * and perform autonegotiation */
+ ret_val = e1000_copper_link_autoneg(hw);
+ if(ret_val)
+ return ret_val;
+ } else {
+ /* PHY will be set to 10H, 10F, 100H,or 100F
+ * depending on value from forced_speed_duplex. */
+ DEBUGOUT("Forcing speed and duplex\n");
+ ret_val = e1000_phy_force_speed_duplex(hw);
+ if(ret_val) {
+ DEBUGOUT("Error Forcing Speed and Duplex\n");
+ return ret_val;
}
- } /* !hw->phy_reset_disable */
+ }
/* Check link status. Wait up to 100 microseconds for link to become
* valid.
@@ -1242,37 +1452,11 @@ e1000_setup_copper_link(struct e1000_hw *hw)
return ret_val;
if(phy_data & MII_SR_LINK_STATUS) {
- /* We have link, so we need to finish the config process:
- * 1) Set up the MAC to the current PHY speed/duplex
- * if we are on 82543. If we
- * are on newer silicon, we only need to configure
- * collision distance in the Transmit Control Register.
- * 2) Set up flow control on the MAC to that established with
- * the link partner.
- */
- if(hw->mac_type >= e1000_82544) {
- e1000_config_collision_dist(hw);
- } else {
- ret_val = e1000_config_mac_to_phy(hw);
- if(ret_val) {
- DEBUGOUT("Error configuring MAC to PHY settings\n");
- return ret_val;
- }
- }
- ret_val = e1000_config_fc_after_link_up(hw);
- if(ret_val) {
- DEBUGOUT("Error Configuring Flow Control\n");
+ /* Config the MAC and PHY after link is up */
+ ret_val = e1000_copper_link_postconfig(hw);
+ if(ret_val)
return ret_val;
- }
- DEBUGOUT("Valid link established!!!\n");
-
- if(hw->phy_type == e1000_phy_igp) {
- ret_val = e1000_config_dsp_after_link_change(hw, TRUE);
- if(ret_val) {
- DEBUGOUT("Error Configuring DSP after link up\n");
- return ret_val;
- }
- }
+
DEBUGOUT("Valid link established!!!\n");
return E1000_SUCCESS;
}
@@ -1302,10 +1486,10 @@ e1000_phy_setup_autoneg(struct e1000_hw *hw)
if(ret_val)
return ret_val;
- /* Read the MII 1000Base-T Control Register (Address 9). */
- ret_val = e1000_read_phy_reg(hw, PHY_1000T_CTRL, &mii_1000t_ctrl_reg);
- if(ret_val)
- return ret_val;
+ /* Read the MII 1000Base-T Control Register (Address 9). */
+ ret_val = e1000_read_phy_reg(hw, PHY_1000T_CTRL, &mii_1000t_ctrl_reg);
+ if(ret_val)
+ return ret_val;
/* Need to parse both autoneg_advertised and fc and set up
* the appropriate PHY registers. First we will parse for
@@ -1417,7 +1601,7 @@ e1000_phy_setup_autoneg(struct e1000_hw *hw)
DEBUGOUT1("Auto-Neg Advertising %x\n", mii_autoneg_adv_reg);
- ret_val = e1000_write_phy_reg(hw, PHY_1000T_CTRL, mii_1000t_ctrl_reg);
+ ret_val = e1000_write_phy_reg(hw, PHY_1000T_CTRL, mii_1000t_ctrl_reg);
if(ret_val)
return ret_val;
@@ -1678,6 +1862,11 @@ e1000_config_mac_to_phy(struct e1000_hw *hw)
DEBUGFUNC("e1000_config_mac_to_phy");
+ /* 82544 or newer MAC, Auto Speed Detection takes care of
+ * MAC speed/duplex configuration.*/
+ if (hw->mac_type >= e1000_82544)
+ return E1000_SUCCESS;
+
/* Read the Device Control Register and set the bits to Force Speed
* and Duplex.
*/
@@ -1688,45 +1877,25 @@ e1000_config_mac_to_phy(struct e1000_hw *hw)
/* Set up duplex in the Device Control and Transmit Control
* registers depending on negotiated values.
*/
- if (hw->phy_type == e1000_phy_igp) {
- ret_val = e1000_read_phy_reg(hw, IGP01E1000_PHY_PORT_STATUS,
- &phy_data);
- if(ret_val)
- return ret_val;
-
- if(phy_data & IGP01E1000_PSSR_FULL_DUPLEX) ctrl |= E1000_CTRL_FD;
- else ctrl &= ~E1000_CTRL_FD;
-
- e1000_config_collision_dist(hw);
+ ret_val = e1000_read_phy_reg(hw, M88E1000_PHY_SPEC_STATUS, &phy_data);
+ if(ret_val)
+ return ret_val;
- /* Set up speed in the Device Control register depending on
- * negotiated values.
- */
- if((phy_data & IGP01E1000_PSSR_SPEED_MASK) ==
- IGP01E1000_PSSR_SPEED_1000MBPS)
- ctrl |= E1000_CTRL_SPD_1000;
- else if((phy_data & IGP01E1000_PSSR_SPEED_MASK) ==
- IGP01E1000_PSSR_SPEED_100MBPS)
- ctrl |= E1000_CTRL_SPD_100;
- } else {
- ret_val = e1000_read_phy_reg(hw, M88E1000_PHY_SPEC_STATUS,
- &phy_data);
- if(ret_val)
- return ret_val;
+ if(phy_data & M88E1000_PSSR_DPLX)
+ ctrl |= E1000_CTRL_FD;
+ else
+ ctrl &= ~E1000_CTRL_FD;
- if(phy_data & M88E1000_PSSR_DPLX) ctrl |= E1000_CTRL_FD;
- else ctrl &= ~E1000_CTRL_FD;
+ e1000_config_collision_dist(hw);
- e1000_config_collision_dist(hw);
+ /* Set up speed in the Device Control register depending on
+ * negotiated values.
+ */
+ if((phy_data & M88E1000_PSSR_SPEED) == M88E1000_PSSR_1000MBS)
+ ctrl |= E1000_CTRL_SPD_1000;
+ else if((phy_data & M88E1000_PSSR_SPEED) == M88E1000_PSSR_100MBS)
+ ctrl |= E1000_CTRL_SPD_100;
- /* Set up speed in the Device Control register depending on
- * negotiated values.
- */
- if((phy_data & M88E1000_PSSR_SPEED) == M88E1000_PSSR_1000MBS)
- ctrl |= E1000_CTRL_SPD_1000;
- else if((phy_data & M88E1000_PSSR_SPEED) == M88E1000_PSSR_100MBS)
- ctrl |= E1000_CTRL_SPD_100;
- }
/* Write the configured values back to the Device Control Reg. */
E1000_WRITE_REG(hw, CTRL, ctrl);
return E1000_SUCCESS;
@@ -2494,8 +2663,8 @@ e1000_read_phy_reg(struct e1000_hw *hw,
DEBUGFUNC("e1000_read_phy_reg");
-
- if(hw->phy_type == e1000_phy_igp &&
+ if((hw->phy_type == e1000_phy_igp ||
+ hw->phy_type == e1000_phy_igp_2) &&
(reg_addr > MAX_PHY_MULTI_PAGE_REG)) {
ret_val = e1000_write_phy_reg_ex(hw, IGP01E1000_PHY_PAGE_SELECT,
(uint16_t)reg_addr);
@@ -2600,8 +2769,8 @@ e1000_write_phy_reg(struct e1000_hw *hw,
DEBUGFUNC("e1000_write_phy_reg");
-
- if(hw->phy_type == e1000_phy_igp &&
+ if((hw->phy_type == e1000_phy_igp ||
+ hw->phy_type == e1000_phy_igp_2) &&
(reg_addr > MAX_PHY_MULTI_PAGE_REG)) {
ret_val = e1000_write_phy_reg_ex(hw, IGP01E1000_PHY_PAGE_SELECT,
(uint16_t)reg_addr);
@@ -2679,19 +2848,27 @@ e1000_write_phy_reg_ex(struct e1000_hw *hw,
return E1000_SUCCESS;
}
+
/******************************************************************************
* Returns the PHY to the power-on reset state
*
* hw - Struct containing variables accessed by shared code
******************************************************************************/
-void
+int32_t
e1000_phy_hw_reset(struct e1000_hw *hw)
{
uint32_t ctrl, ctrl_ext;
uint32_t led_ctrl;
+ int32_t ret_val;
DEBUGFUNC("e1000_phy_hw_reset");
+ /* In the case of the phy reset being blocked, it's not an error, we
+ * simply return success without performing the reset. */
+ ret_val = e1000_check_phy_reset_block(hw);
+ if (ret_val)
+ return E1000_SUCCESS;
+
DEBUGOUT("Resetting Phy...\n");
if(hw->mac_type > e1000_82543) {
@@ -2727,6 +2904,11 @@ e1000_phy_hw_reset(struct e1000_hw *hw)
led_ctrl |= (IGP_ACTIVITY_LED_ENABLE | IGP_LED3_MODE);
E1000_WRITE_REG(hw, LEDCTL, led_ctrl);
}
+
+ /* Wait for FW to finish PHY configuration. */
+ ret_val = e1000_get_phy_cfg_done(hw);
+
+ return ret_val;
}
/******************************************************************************
@@ -2744,7 +2926,19 @@ e1000_phy_reset(struct e1000_hw *hw)
DEBUGFUNC("e1000_phy_reset");
- if(hw->mac_type != e1000_82541_rev_2) {
+ /* In the case of the phy reset being blocked, it's not an error, we
+ * simply return success without performing the reset. */
+ ret_val = e1000_check_phy_reset_block(hw);
+ if (ret_val)
+ return E1000_SUCCESS;
+
+ switch (hw->mac_type) {
+ case e1000_82541_rev_2:
+ ret_val = e1000_phy_hw_reset(hw);
+ if(ret_val)
+ return ret_val;
+ break;
+ default:
ret_val = e1000_read_phy_reg(hw, PHY_CTRL, &phy_data);
if(ret_val)
return ret_val;
@@ -2755,9 +2949,10 @@ e1000_phy_reset(struct e1000_hw *hw)
return ret_val;
udelay(1);
- } else e1000_phy_hw_reset(hw);
+ break;
+ }
- if(hw->phy_type == e1000_phy_igp)
+ if(hw->phy_type == e1000_phy_igp || hw->phy_type == e1000_phy_igp_2)
e1000_phy_init_script(hw);
return E1000_SUCCESS;
@@ -2811,6 +3006,9 @@ e1000_detect_gig_phy(struct e1000_hw *hw)
case e1000_82547_rev_2:
if(hw->phy_id == IGP01E1000_I_PHY_ID) match = TRUE;
break;
+ case e1000_82573:
+ if(hw->phy_id == M88E1111_I_PHY_ID) match = TRUE;
+ break;
default:
DEBUGOUT1("Invalid MAC type %d\n", hw->mac_type);
return -E1000_ERR_CONFIG;
@@ -2866,7 +3064,7 @@ e1000_phy_igp_get_info(struct e1000_hw *hw,
/* The downshift status is checked only once, after link is established,
* and it stored in the hw->speed_downgraded parameter. */
- phy_info->downshift = hw->speed_downgraded;
+ phy_info->downshift = (e1000_downshift)hw->speed_downgraded;
/* IGP01E1000 does not need to support it. */
phy_info->extended_10bt_distance = e1000_10bt_ext_dist_enable_normal;
@@ -2905,7 +3103,7 @@ e1000_phy_igp_get_info(struct e1000_hw *hw,
if(ret_val)
return ret_val;
- /* transalte to old method */
+ /* Translate to old method */
average = (max_length + min_length) / 2;
if(average <= e1000_igp_cable_length_50)
@@ -2940,7 +3138,7 @@ e1000_phy_m88_get_info(struct e1000_hw *hw,
/* The downshift status is checked only once, after link is established,
* and it stored in the hw->speed_downgraded parameter. */
- phy_info->downshift = hw->speed_downgraded;
+ phy_info->downshift = (e1000_downshift)hw->speed_downgraded;
ret_val = e1000_read_phy_reg(hw, M88E1000_PHY_SPEC_CTRL, &phy_data);
if(ret_val)
@@ -3029,7 +3227,8 @@ e1000_phy_get_info(struct e1000_hw *hw,
return -E1000_ERR_CONFIG;
}
- if(hw->phy_type == e1000_phy_igp)
+ if(hw->phy_type == e1000_phy_igp ||
+ hw->phy_type == e1000_phy_igp_2)
return e1000_phy_igp_get_info(hw, phy_info);
else
return e1000_phy_m88_get_info(hw, phy_info);
@@ -3055,11 +3254,12 @@ e1000_validate_mdi_setting(struct e1000_hw *hw)
*
* hw - Struct containing variables accessed by shared code
*****************************************************************************/
-void
+int32_t
e1000_init_eeprom_params(struct e1000_hw *hw)
{
struct e1000_eeprom_info *eeprom = &hw->eeprom;
uint32_t eecd = E1000_READ_REG(hw, EECD);
+ int32_t ret_val = E1000_SUCCESS;
uint16_t eeprom_size;
DEBUGFUNC("e1000_init_eeprom_params");
@@ -3074,6 +3274,8 @@ e1000_init_eeprom_params(struct e1000_hw *hw)
eeprom->opcode_bits = 3;
eeprom->address_bits = 6;
eeprom->delay_usec = 50;
+ eeprom->use_eerd = FALSE;
+ eeprom->use_eewr = FALSE;
break;
case e1000_82540:
case e1000_82545:
@@ -3090,6 +3292,8 @@ e1000_init_eeprom_params(struct e1000_hw *hw)
eeprom->word_size = 64;
eeprom->address_bits = 6;
}
+ eeprom->use_eerd = FALSE;
+ eeprom->use_eewr = FALSE;
break;
case e1000_82541:
case e1000_82541_rev_2:
@@ -3118,42 +3322,60 @@ e1000_init_eeprom_params(struct e1000_hw *hw)
eeprom->address_bits = 6;
}
}
+ eeprom->use_eerd = FALSE;
+ eeprom->use_eewr = FALSE;
+ break;
+ case e1000_82573:
+ eeprom->type = e1000_eeprom_spi;
+ eeprom->opcode_bits = 8;
+ eeprom->delay_usec = 1;
+ if (eecd & E1000_EECD_ADDR_BITS) {
+ eeprom->page_size = 32;
+ eeprom->address_bits = 16;
+ } else {
+ eeprom->page_size = 8;
+ eeprom->address_bits = 8;
+ }
+ eeprom->use_eerd = TRUE;
+ eeprom->use_eewr = TRUE;
+ if(e1000_is_onboard_nvm_eeprom(hw) == FALSE) {
+ eeprom->type = e1000_eeprom_flash;
+ eeprom->word_size = 2048;
+
+ /* Ensure that the Autonomous FLASH update bit is cleared due to
+ * Flash update issue on parts which use a FLASH for NVM. */
+ eecd &= ~E1000_EECD_AUPDEN;
+ E1000_WRITE_REG(hw, EECD, eecd);
+ }
break;
default:
break;
}
if (eeprom->type == e1000_eeprom_spi) {
- eeprom->word_size = 64;
- if (e1000_read_eeprom(hw, EEPROM_CFG, 1, &eeprom_size) == 0) {
- eeprom_size &= EEPROM_SIZE_MASK;
-
- switch (eeprom_size) {
- case EEPROM_SIZE_16KB:
- eeprom->word_size = 8192;
- break;
- case EEPROM_SIZE_8KB:
- eeprom->word_size = 4096;
- break;
- case EEPROM_SIZE_4KB:
- eeprom->word_size = 2048;
- break;
- case EEPROM_SIZE_2KB:
- eeprom->word_size = 1024;
- break;
- case EEPROM_SIZE_1KB:
- eeprom->word_size = 512;
- break;
- case EEPROM_SIZE_512B:
- eeprom->word_size = 256;
- break;
- case EEPROM_SIZE_128B:
- default:
- eeprom->word_size = 64;
- break;
- }
+ /* eeprom_size will be an enum [0..8] that maps to eeprom sizes 128B to
+ * 32KB (incremented by powers of 2).
+ */
+ if(hw->mac_type <= e1000_82547_rev_2) {
+ /* Set to default value for initial eeprom read. */
+ eeprom->word_size = 64;
+ ret_val = e1000_read_eeprom(hw, EEPROM_CFG, 1, &eeprom_size);
+ if(ret_val)
+ return ret_val;
+ eeprom_size = (eeprom_size & EEPROM_SIZE_MASK) >> EEPROM_SIZE_SHIFT;
+ /* 256B eeprom size was not supported in earlier hardware, so we
+ * bump eeprom_size up one to ensure that "1" (which maps to 256B)
+ * is never the result used in the shifting logic below. */
+ if(eeprom_size)
+ eeprom_size++;
+ } else {
+ eeprom_size = (uint16_t)((eecd & E1000_EECD_SIZE_EX_MASK) >>
+ E1000_EECD_SIZE_EX_SHIFT);
}
+
+ eeprom->word_size = 1 << (eeprom_size + EEPROM_WORD_SIZE_SHIFT);
}
+ return ret_val;
}
/******************************************************************************
@@ -3306,8 +3528,12 @@ e1000_acquire_eeprom(struct e1000_hw *hw)
DEBUGFUNC("e1000_acquire_eeprom");
+ if(e1000_get_hw_eeprom_semaphore(hw))
+ return -E1000_ERR_EEPROM;
+
eecd = E1000_READ_REG(hw, EECD);
+ if (hw->mac_type != e1000_82573) {
/* Request EEPROM Access */
if(hw->mac_type > e1000_82544) {
eecd |= E1000_EECD_REQ;
@@ -3326,6 +3552,7 @@ e1000_acquire_eeprom(struct e1000_hw *hw)
return -E1000_ERR_EEPROM;
}
}
+ }
/* Setup EEPROM for Read/Write */
@@ -3443,6 +3670,8 @@ e1000_release_eeprom(struct e1000_hw *hw)
eecd &= ~E1000_EECD_REQ;
E1000_WRITE_REG(hw, EECD, eecd);
}
+
+ e1000_put_hw_eeprom_semaphore(hw);
}
/******************************************************************************
@@ -3504,8 +3733,10 @@ e1000_read_eeprom(struct e1000_hw *hw,
{
struct e1000_eeprom_info *eeprom = &hw->eeprom;
uint32_t i = 0;
+ int32_t ret_val;
DEBUGFUNC("e1000_read_eeprom");
+
/* A check for invalid values: offset too large, too many words, and not
* enough words.
*/
@@ -3515,9 +3746,23 @@ e1000_read_eeprom(struct e1000_hw *hw,
return -E1000_ERR_EEPROM;
}
- /* Prepare the EEPROM for reading */
- if(e1000_acquire_eeprom(hw) != E1000_SUCCESS)
- return -E1000_ERR_EEPROM;
+ /* FLASH reads without acquiring the semaphore are safe in 82573-based
+ * controllers.
+ */
+ if ((e1000_is_onboard_nvm_eeprom(hw) == TRUE) ||
+ (hw->mac_type != e1000_82573)) {
+ /* Prepare the EEPROM for reading */
+ if(e1000_acquire_eeprom(hw) != E1000_SUCCESS)
+ return -E1000_ERR_EEPROM;
+ }
+
+ if(eeprom->use_eerd == TRUE) {
+ ret_val = e1000_read_eeprom_eerd(hw, offset, words, data);
+ if ((e1000_is_onboard_nvm_eeprom(hw) == TRUE) ||
+ (hw->mac_type != e1000_82573))
+ e1000_release_eeprom(hw);
+ return ret_val;
+ }
if(eeprom->type == e1000_eeprom_spi) {
uint16_t word_in;
@@ -3569,6 +3814,132 @@ e1000_read_eeprom(struct e1000_hw *hw,
}
/******************************************************************************
+ * Reads a 16 bit word from the EEPROM using the EERD register.
+ *
+ * hw - Struct containing variables accessed by shared code
+ * offset - offset of word in the EEPROM to read
+ * data - word read from the EEPROM
+ * words - number of words to read
+ *****************************************************************************/
+int32_t
+e1000_read_eeprom_eerd(struct e1000_hw *hw,
+ uint16_t offset,
+ uint16_t words,
+ uint16_t *data)
+{
+ uint32_t i, eerd = 0;
+ int32_t error = 0;
+
+ for (i = 0; i < words; i++) {
+ eerd = ((offset+i) << E1000_EEPROM_RW_ADDR_SHIFT) +
+ E1000_EEPROM_RW_REG_START;
+
+ E1000_WRITE_REG(hw, EERD, eerd);
+ error = e1000_poll_eerd_eewr_done(hw, E1000_EEPROM_POLL_READ);
+
+ if(error) {
+ break;
+ }
+ data[i] = (E1000_READ_REG(hw, EERD) >> E1000_EEPROM_RW_REG_DATA);
+
+ }
+
+ return error;
+}
+
+/******************************************************************************
+ * Writes a 16 bit word from the EEPROM using the EEWR register.
+ *
+ * hw - Struct containing variables accessed by shared code
+ * offset - offset of word in the EEPROM to read
+ * data - word read from the EEPROM
+ * words - number of words to read
+ *****************************************************************************/
+int32_t
+e1000_write_eeprom_eewr(struct e1000_hw *hw,
+ uint16_t offset,
+ uint16_t words,
+ uint16_t *data)
+{
+ uint32_t register_value = 0;
+ uint32_t i = 0;
+ int32_t error = 0;
+
+ for (i = 0; i < words; i++) {
+ register_value = (data[i] << E1000_EEPROM_RW_REG_DATA) |
+ ((offset+i) << E1000_EEPROM_RW_ADDR_SHIFT) |
+ E1000_EEPROM_RW_REG_START;
+
+ error = e1000_poll_eerd_eewr_done(hw, E1000_EEPROM_POLL_WRITE);
+ if(error) {
+ break;
+ }
+
+ E1000_WRITE_REG(hw, EEWR, register_value);
+
+ error = e1000_poll_eerd_eewr_done(hw, E1000_EEPROM_POLL_WRITE);
+
+ if(error) {
+ break;
+ }
+ }
+
+ return error;
+}
+
+/******************************************************************************
+ * Polls the status bit (bit 1) of the EERD to determine when the read is done.
+ *
+ * hw - Struct containing variables accessed by shared code
+ *****************************************************************************/
+int32_t
+e1000_poll_eerd_eewr_done(struct e1000_hw *hw, int eerd)
+{
+ uint32_t attempts = 100000;
+ uint32_t i, reg = 0;
+ int32_t done = E1000_ERR_EEPROM;
+
+ for(i = 0; i < attempts; i++) {
+ if(eerd == E1000_EEPROM_POLL_READ)
+ reg = E1000_READ_REG(hw, EERD);
+ else
+ reg = E1000_READ_REG(hw, EEWR);
+
+ if(reg & E1000_EEPROM_RW_REG_DONE) {
+ done = E1000_SUCCESS;
+ break;
+ }
+ udelay(5);
+ }
+
+ return done;
+}
+
+/***************************************************************************
+* Description: Determines if the onboard NVM is FLASH or EEPROM.
+*
+* hw - Struct containing variables accessed by shared code
+****************************************************************************/
+boolean_t
+e1000_is_onboard_nvm_eeprom(struct e1000_hw *hw)
+{
+ uint32_t eecd = 0;
+
+ if(hw->mac_type == e1000_82573) {
+ eecd = E1000_READ_REG(hw, EECD);
+
+ /* Isolate bits 15 & 16 */
+ eecd = ((eecd >> 15) & 0x03);
+
+ /* If both bits are set, device is Flash type */
+ if(eecd == 0x03) {
+ return FALSE;
+ }
+ }
+ return TRUE;
+}
+
+/******************************************************************************
* Verifies that the EEPROM has a valid checksum
*
* hw - Struct containing variables accessed by shared code
@@ -3585,6 +3956,25 @@ e1000_validate_eeprom_checksum(struct e1000_hw *hw)
DEBUGFUNC("e1000_validate_eeprom_checksum");
+ if ((hw->mac_type == e1000_82573) &&
+ (e1000_is_onboard_nvm_eeprom(hw) == FALSE)) {
+ /* Check bit 4 of word 10h. If it is 0, firmware is done updating
+ * 10h-12h. Checksum may need to be fixed. */
+ e1000_read_eeprom(hw, 0x10, 1, &eeprom_data);
+ if ((eeprom_data & 0x10) == 0) {
+ /* Read 0x23 and check bit 15. This bit is a 1 when the checksum
+ * has already been fixed. If the checksum is still wrong and this
+ * bit is a 1, we need to return bad checksum. Otherwise, we need
+ * to set this bit to a 1 and update the checksum. */
+ e1000_read_eeprom(hw, 0x23, 1, &eeprom_data);
+ if ((eeprom_data & 0x8000) == 0) {
+ eeprom_data |= 0x8000;
+ e1000_write_eeprom(hw, 0x23, 1, &eeprom_data);
+ e1000_update_eeprom_checksum(hw);
+ }
+ }
+ }
+
for(i = 0; i < (EEPROM_CHECKSUM_REG + 1); i++) {
if(e1000_read_eeprom(hw, i, 1, &eeprom_data) < 0) {
DEBUGOUT("EEPROM Read Error\n");
@@ -3628,6 +4018,8 @@ e1000_update_eeprom_checksum(struct e1000_hw *hw)
if(e1000_write_eeprom(hw, EEPROM_CHECKSUM_REG, 1, &checksum) < 0) {
DEBUGOUT("EEPROM Write Error\n");
return -E1000_ERR_EEPROM;
+ } else if (hw->eeprom.type == e1000_eeprom_flash) {
+ e1000_commit_shadow_ram(hw);
}
return E1000_SUCCESS;
}
@@ -3663,6 +4055,10 @@ e1000_write_eeprom(struct e1000_hw *hw,
return -E1000_ERR_EEPROM;
}
+ /* 82573 reads only through eerd */
+ if(eeprom->use_eewr == TRUE)
+ return e1000_write_eeprom_eewr(hw, offset, words, data);
+
/* Prepare the EEPROM for writing */
if (e1000_acquire_eeprom(hw) != E1000_SUCCESS)
return -E1000_ERR_EEPROM;
@@ -3833,6 +4229,65 @@ e1000_write_eeprom_microwire(struct e1000_hw *hw,
}
/******************************************************************************
+ * Flushes the cached eeprom to NVM. This is done by saving the modified values
+ * in the eeprom cache and the non modified values in the currently active bank
+ * to the new bank.
+ *
+ * hw - Struct containing variables accessed by shared code
+ * offset - offset of word in the EEPROM to read
+ * data - word read from the EEPROM
+ * words - number of words to read
+ *****************************************************************************/
+int32_t
+e1000_commit_shadow_ram(struct e1000_hw *hw)
+{
+ uint32_t attempts = 100000;
+ uint32_t eecd = 0;
+ uint32_t flop = 0;
+ uint32_t i = 0;
+ int32_t error = E1000_SUCCESS;
+
+ /* The flop register will be used to determine if flash type is STM */
+ flop = E1000_READ_REG(hw, FLOP);
+
+ if (hw->mac_type == e1000_82573) {
+ for (i=0; i < attempts; i++) {
+ eecd = E1000_READ_REG(hw, EECD);
+ if ((eecd & E1000_EECD_FLUPD) == 0) {
+ break;
+ }
+ udelay(5);
+ }
+
+ if (i == attempts) {
+ return -E1000_ERR_EEPROM;
+ }
+
+ /* If STM opcode located in bits 15:8 of flop, reset firmware */
+ if ((flop & 0xFF00) == E1000_STM_OPCODE) {
+ E1000_WRITE_REG(hw, HICR, E1000_HICR_FW_RESET);
+ }
+
+ /* Perform the flash update */
+ E1000_WRITE_REG(hw, EECD, eecd | E1000_EECD_FLUPD);
+
+ for (i=0; i < attempts; i++) {
+ eecd = E1000_READ_REG(hw, EECD);
+ if ((eecd & E1000_EECD_FLUPD) == 0) {
+ break;
+ }
+ udelay(5);
+ }
+
+ if (i == attempts) {
+ return -E1000_ERR_EEPROM;
+ }
+ }
+
+ return error;
+}
+
+/******************************************************************************
* Reads the adapter's part number from the EEPROM
*
* hw - Struct containing variables accessed by shared code
@@ -3911,6 +4366,7 @@ void
e1000_init_rx_addrs(struct e1000_hw *hw)
{
uint32_t i;
+ uint32_t rar_num;
DEBUGFUNC("e1000_init_rx_addrs");
@@ -3919,9 +4375,10 @@ e1000_init_rx_addrs(struct e1000_hw *hw)
e1000_rar_set(hw, hw->mac_addr, 0);
+ rar_num = E1000_RAR_ENTRIES;
/* Zero out the other 15 receive addresses. */
DEBUGOUT("Clearing RAR[1-15]\n");
- for(i = 1; i < E1000_RAR_ENTRIES; i++) {
+ for(i = 1; i < rar_num; i++) {
E1000_WRITE_REG_ARRAY(hw, RA, (i << 1), 0);
E1000_WRITE_REG_ARRAY(hw, RA, ((i << 1) + 1), 0);
}
@@ -3950,7 +4407,9 @@ e1000_mc_addr_list_update(struct e1000_hw *hw,
{
uint32_t hash_value;
uint32_t i;
-
+ uint32_t num_rar_entry;
+ uint32_t num_mta_entry;
+
DEBUGFUNC("e1000_mc_addr_list_update");
/* Set the new number of MC addresses that we are being requested to use. */
@@ -3958,14 +4417,16 @@ e1000_mc_addr_list_update(struct e1000_hw *hw,
/* Clear RAR[1-15] */
DEBUGOUT(" Clearing RAR[1-15]\n");
- for(i = rar_used_count; i < E1000_RAR_ENTRIES; i++) {
+ num_rar_entry = E1000_RAR_ENTRIES;
+ for(i = rar_used_count; i < num_rar_entry; i++) {
E1000_WRITE_REG_ARRAY(hw, RA, (i << 1), 0);
E1000_WRITE_REG_ARRAY(hw, RA, ((i << 1) + 1), 0);
}
/* Clear the MTA */
DEBUGOUT(" Clearing MTA\n");
- for(i = 0; i < E1000_NUM_MTA_REGISTERS; i++) {
+ num_mta_entry = E1000_NUM_MTA_REGISTERS;
+ for(i = 0; i < num_mta_entry; i++) {
E1000_WRITE_REG_ARRAY(hw, MTA, i, 0);
}
@@ -3989,7 +4450,7 @@ e1000_mc_addr_list_update(struct e1000_hw *hw,
/* Place this multicast address in the RAR if there is room, *
* else put it in the MTA
*/
- if(rar_used_count < E1000_RAR_ENTRIES) {
+ if (rar_used_count < num_rar_entry) {
e1000_rar_set(hw,
mc_addr_list + (i * (ETH_LENGTH_OF_ADDRESS + pad)),
rar_used_count);
@@ -4040,6 +4501,7 @@ e1000_hash_mc_addr(struct e1000_hw *hw,
}
hash_value &= 0xFFF;
+
return hash_value;
}
@@ -4144,12 +4606,33 @@ void
e1000_clear_vfta(struct e1000_hw *hw)
{
uint32_t offset;
-
- for(offset = 0; offset < E1000_VLAN_FILTER_TBL_SIZE; offset++)
- E1000_WRITE_REG_ARRAY(hw, VFTA, offset, 0);
+ uint32_t vfta_value = 0;
+ uint32_t vfta_offset = 0;
+ uint32_t vfta_bit_in_reg = 0;
+
+ if (hw->mac_type == e1000_82573) {
+ if (hw->mng_cookie.vlan_id != 0) {
+ /* The VFTA is a 4096b bit-field, each identifying a single VLAN
+ * ID. The following operations determine which 32b entry
+ * (i.e. offset) into the array we want to set the VLAN ID
+ * (i.e. bit) of the manageability unit. */
+ vfta_offset = (hw->mng_cookie.vlan_id >>
+ E1000_VFTA_ENTRY_SHIFT) &
+ E1000_VFTA_ENTRY_MASK;
+ vfta_bit_in_reg = 1 << (hw->mng_cookie.vlan_id &
+ E1000_VFTA_ENTRY_BIT_SHIFT_MASK);
+ }
+ }
+ for (offset = 0; offset < E1000_VLAN_FILTER_TBL_SIZE; offset++) {
+ /* If the offset we want to clear is the same offset of the
+ * manageability VLAN ID, then clear all bits except that of the
+ * manageability unit */
+ vfta_value = (offset == vfta_offset) ? vfta_bit_in_reg : 0;
+ E1000_WRITE_REG_ARRAY(hw, VFTA, offset, vfta_value);
+ }
}
-static int32_t
+int32_t
e1000_id_led_init(struct e1000_hw * hw)
{
uint32_t ledctl;
@@ -4480,6 +4963,19 @@ e1000_clear_hw_cntrs(struct e1000_hw *hw)
temp = E1000_READ_REG(hw, MGTPRC);
temp = E1000_READ_REG(hw, MGTPDC);
temp = E1000_READ_REG(hw, MGTPTC);
+
+ if(hw->mac_type <= e1000_82547_rev_2) return;
+
+ temp = E1000_READ_REG(hw, IAC);
+ temp = E1000_READ_REG(hw, ICRXOC);
+ temp = E1000_READ_REG(hw, ICRXPTC);
+ temp = E1000_READ_REG(hw, ICRXATC);
+ temp = E1000_READ_REG(hw, ICTXPTC);
+ temp = E1000_READ_REG(hw, ICTXATC);
+ temp = E1000_READ_REG(hw, ICTXQEC);
+ temp = E1000_READ_REG(hw, ICTXQMTC);
+ temp = E1000_READ_REG(hw, ICRXDMTC);
+
}
/******************************************************************************
@@ -4646,6 +5142,11 @@ e1000_get_bus_info(struct e1000_hw *hw)
hw->bus_speed = e1000_bus_speed_unknown;
hw->bus_width = e1000_bus_width_unknown;
break;
+ case e1000_82573:
+ hw->bus_type = e1000_bus_type_pci_express;
+ hw->bus_speed = e1000_bus_speed_2500;
+ hw->bus_width = e1000_bus_width_pciex_4;
+ break;
default:
status = E1000_READ_REG(hw, STATUS);
hw->bus_type = (status & E1000_STATUS_PCIX_MODE) ?
@@ -4749,6 +5250,7 @@ e1000_get_cable_length(struct e1000_hw *hw,
/* Use old method for Phy older than IGP */
if(hw->phy_type == e1000_phy_m88) {
+
ret_val = e1000_read_phy_reg(hw, M88E1000_PHY_SPEC_STATUS,
&phy_data);
if(ret_val)
@@ -4865,7 +5367,8 @@ e1000_check_polarity(struct e1000_hw *hw,
return ret_val;
*polarity = (phy_data & M88E1000_PSSR_REV_POLARITY) >>
M88E1000_PSSR_REV_POLARITY_SHIFT;
- } else if(hw->phy_type == e1000_phy_igp) {
+ } else if(hw->phy_type == e1000_phy_igp ||
+ hw->phy_type == e1000_phy_igp_2) {
/* Read the Status register to check the speed */
ret_val = e1000_read_phy_reg(hw, IGP01E1000_PHY_PORT_STATUS,
&phy_data);
@@ -4917,7 +5420,8 @@ e1000_check_downshift(struct e1000_hw *hw)
DEBUGFUNC("e1000_check_downshift");
- if(hw->phy_type == e1000_phy_igp) {
+ if(hw->phy_type == e1000_phy_igp ||
+ hw->phy_type == e1000_phy_igp_2) {
ret_val = e1000_read_phy_reg(hw, IGP01E1000_PHY_LINK_HEALTH,
&phy_data);
if(ret_val)
@@ -4933,6 +5437,7 @@ e1000_check_downshift(struct e1000_hw *hw)
hw->speed_downgraded = (phy_data & M88E1000_PSSR_DOWNSHIFT) >>
M88E1000_PSSR_DOWNSHIFT_SHIFT;
}
+
return E1000_SUCCESS;
}
@@ -5047,7 +5552,7 @@ e1000_config_dsp_after_link_change(struct e1000_hw *hw,
if(ret_val)
return ret_val;
- msec_delay(20);
+ msec_delay_irq(20);
ret_val = e1000_write_phy_reg(hw, 0x0000,
IGP01E1000_IEEE_FORCE_GIGA);
@@ -5071,7 +5576,7 @@ e1000_config_dsp_after_link_change(struct e1000_hw *hw,
if(ret_val)
return ret_val;
- msec_delay(20);
+ msec_delay_irq(20);
/* Now enable the transmitter */
ret_val = e1000_write_phy_reg(hw, 0x2F5B, phy_saved_data);
@@ -5096,7 +5601,7 @@ e1000_config_dsp_after_link_change(struct e1000_hw *hw,
if(ret_val)
return ret_val;
- msec_delay(20);
+ msec_delay_irq(20);
ret_val = e1000_write_phy_reg(hw, 0x0000,
IGP01E1000_IEEE_FORCE_GIGA);
@@ -5112,7 +5617,7 @@ e1000_config_dsp_after_link_change(struct e1000_hw *hw,
if(ret_val)
return ret_val;
- msec_delay(20);
+ msec_delay_irq(20);
/* Now enable the transmitter */
ret_val = e1000_write_phy_reg(hw, 0x2F5B, phy_saved_data);
@@ -5187,22 +5692,36 @@ e1000_set_d3_lplu_state(struct e1000_hw *hw,
uint16_t phy_data;
DEBUGFUNC("e1000_set_d3_lplu_state");
- if(!((hw->mac_type == e1000_82541_rev_2) ||
- (hw->mac_type == e1000_82547_rev_2)))
+ if(hw->phy_type != e1000_phy_igp && hw->phy_type != e1000_phy_igp_2)
return E1000_SUCCESS;
/* During driver activity LPLU should not be used or it will attain link
* from the lowest speeds starting from 10Mbps. The capability is used for
* Dx transitions and states */
- ret_val = e1000_read_phy_reg(hw, IGP01E1000_GMII_FIFO, &phy_data);
- if(ret_val)
- return ret_val;
-
- if(!active) {
- phy_data &= ~IGP01E1000_GMII_FLEX_SPD;
- ret_val = e1000_write_phy_reg(hw, IGP01E1000_GMII_FIFO, phy_data);
+ if(hw->mac_type == e1000_82541_rev_2 || hw->mac_type == e1000_82547_rev_2) {
+ ret_val = e1000_read_phy_reg(hw, IGP01E1000_GMII_FIFO, &phy_data);
if(ret_val)
return ret_val;
+ } else {
+ ret_val = e1000_read_phy_reg(hw, IGP02E1000_PHY_POWER_MGMT, &phy_data);
+ if(ret_val)
+ return ret_val;
+ }
+
+ if(!active) {
+ if(hw->mac_type == e1000_82541_rev_2 ||
+ hw->mac_type == e1000_82547_rev_2) {
+ phy_data &= ~IGP01E1000_GMII_FLEX_SPD;
+ ret_val = e1000_write_phy_reg(hw, IGP01E1000_GMII_FIFO, phy_data);
+ if(ret_val)
+ return ret_val;
+ } else {
+ phy_data &= ~IGP02E1000_PM_D3_LPLU;
+ ret_val = e1000_write_phy_reg(hw, IGP02E1000_PHY_POWER_MGMT,
+ phy_data);
+ if (ret_val)
+ return ret_val;
+ }
/* LPLU and SmartSpeed are mutually exclusive. LPLU is used during
* Dx states where the power conservation is most important. During
@@ -5236,11 +5755,105 @@ e1000_set_d3_lplu_state(struct e1000_hw *hw,
(hw->autoneg_advertised == AUTONEG_ADVERTISE_10_ALL ) ||
(hw->autoneg_advertised == AUTONEG_ADVERTISE_10_100_ALL)) {
- phy_data |= IGP01E1000_GMII_FLEX_SPD;
- ret_val = e1000_write_phy_reg(hw, IGP01E1000_GMII_FIFO, phy_data);
+ if(hw->mac_type == e1000_82541_rev_2 ||
+ hw->mac_type == e1000_82547_rev_2) {
+ phy_data |= IGP01E1000_GMII_FLEX_SPD;
+ ret_val = e1000_write_phy_reg(hw, IGP01E1000_GMII_FIFO, phy_data);
+ if(ret_val)
+ return ret_val;
+ } else {
+ phy_data |= IGP02E1000_PM_D3_LPLU;
+ ret_val = e1000_write_phy_reg(hw, IGP02E1000_PHY_POWER_MGMT,
+ phy_data);
+ if (ret_val)
+ return ret_val;
+ }
+
+ /* When LPLU is enabled we should disable SmartSpeed */
+ ret_val = e1000_read_phy_reg(hw, IGP01E1000_PHY_PORT_CONFIG, &phy_data);
+ if(ret_val)
+ return ret_val;
+
+ phy_data &= ~IGP01E1000_PSCFR_SMART_SPEED;
+ ret_val = e1000_write_phy_reg(hw, IGP01E1000_PHY_PORT_CONFIG, phy_data);
if(ret_val)
return ret_val;
+ }
+ return E1000_SUCCESS;
+}
+
+/*****************************************************************************
+ *
+ * This function sets the lplu d0 state according to the active flag. When
+ * activating lplu this function also disables smart speed and vise versa.
+ * lplu will not be activated unless the device autonegotiation advertisment
+ * meets standards of either 10 or 10/100 or 10/100/1000 at all duplexes.
+ * hw: Struct containing variables accessed by shared code
+ * active - true to enable lplu false to disable lplu.
+ *
+ * returns: - E1000_ERR_PHY if fail to read/write the PHY
+ * E1000_SUCCESS at any other case.
+ *
+ ****************************************************************************/
+
+int32_t
+e1000_set_d0_lplu_state(struct e1000_hw *hw,
+ boolean_t active)
+{
+ int32_t ret_val;
+ uint16_t phy_data;
+ DEBUGFUNC("e1000_set_d0_lplu_state");
+
+ if(hw->mac_type <= e1000_82547_rev_2)
+ return E1000_SUCCESS;
+
+ ret_val = e1000_read_phy_reg(hw, IGP02E1000_PHY_POWER_MGMT, &phy_data);
+ if(ret_val)
+ return ret_val;
+
+ if (!active) {
+ phy_data &= ~IGP02E1000_PM_D0_LPLU;
+ ret_val = e1000_write_phy_reg(hw, IGP02E1000_PHY_POWER_MGMT, phy_data);
+ if (ret_val)
+ return ret_val;
+
+ /* LPLU and SmartSpeed are mutually exclusive. LPLU is used during
+ * Dx states where the power conservation is most important. During
+ * driver activity we should enable SmartSpeed, so performance is
+ * maintained. */
+ if (hw->smart_speed == e1000_smart_speed_on) {
+ ret_val = e1000_read_phy_reg(hw, IGP01E1000_PHY_PORT_CONFIG,
+ &phy_data);
+ if(ret_val)
+ return ret_val;
+
+ phy_data |= IGP01E1000_PSCFR_SMART_SPEED;
+ ret_val = e1000_write_phy_reg(hw, IGP01E1000_PHY_PORT_CONFIG,
+ phy_data);
+ if(ret_val)
+ return ret_val;
+ } else if (hw->smart_speed == e1000_smart_speed_off) {
+ ret_val = e1000_read_phy_reg(hw, IGP01E1000_PHY_PORT_CONFIG,
+ &phy_data);
+ if (ret_val)
+ return ret_val;
+
+ phy_data &= ~IGP01E1000_PSCFR_SMART_SPEED;
+ ret_val = e1000_write_phy_reg(hw, IGP01E1000_PHY_PORT_CONFIG,
+ phy_data);
+ if(ret_val)
+ return ret_val;
+ }
+
+
+ } else {
+
+ phy_data |= IGP02E1000_PM_D0_LPLU;
+ ret_val = e1000_write_phy_reg(hw, IGP02E1000_PHY_POWER_MGMT, phy_data);
+ if (ret_val)
+ return ret_val;
+
/* When LPLU is enabled we should disable SmartSpeed */
ret_val = e1000_read_phy_reg(hw, IGP01E1000_PHY_PORT_CONFIG, &phy_data);
if(ret_val)
@@ -5318,6 +5931,338 @@ e1000_set_vco_speed(struct e1000_hw *hw)
return E1000_SUCCESS;
}
+
+/*****************************************************************************
+ * This function reads the cookie from ARC ram.
+ *
+ * returns: - E1000_SUCCESS .
+ ****************************************************************************/
+int32_t
+e1000_host_if_read_cookie(struct e1000_hw * hw, uint8_t *buffer)
+{
+ uint8_t i;
+ uint32_t offset = E1000_MNG_DHCP_COOKIE_OFFSET;
+ uint8_t length = E1000_MNG_DHCP_COOKIE_LENGTH;
+
+ length = (length >> 2);
+ offset = (offset >> 2);
+
+ for (i = 0; i < length; i++) {
+ *((uint32_t *) buffer + i) =
+ E1000_READ_REG_ARRAY_DWORD(hw, HOST_IF, offset + i);
+ }
+ return E1000_SUCCESS;
+}
+
+
+/*****************************************************************************
+ * This function checks whether the HOST IF is enabled for command operaton
+ * and also checks whether the previous command is completed.
+ * It busy waits in case of previous command is not completed.
+ *
+ * returns: - E1000_ERR_HOST_INTERFACE_COMMAND in case if is not ready or
+ * timeout
+ * - E1000_SUCCESS for success.
+ ****************************************************************************/
+int32_t
+e1000_mng_enable_host_if(struct e1000_hw * hw)
+{
+ uint32_t hicr;
+ uint8_t i;
+
+ /* Check that the host interface is enabled. */
+ hicr = E1000_READ_REG(hw, HICR);
+ if ((hicr & E1000_HICR_EN) == 0) {
+ DEBUGOUT("E1000_HOST_EN bit disabled.\n");
+ return -E1000_ERR_HOST_INTERFACE_COMMAND;
+ }
+ /* check the previous command is completed */
+ for (i = 0; i < E1000_MNG_DHCP_COMMAND_TIMEOUT; i++) {
+ hicr = E1000_READ_REG(hw, HICR);
+ if (!(hicr & E1000_HICR_C))
+ break;
+ msec_delay_irq(1);
+ }
+
+ if (i == E1000_MNG_DHCP_COMMAND_TIMEOUT) {
+ DEBUGOUT("Previous command timeout failed .\n");
+ return -E1000_ERR_HOST_INTERFACE_COMMAND;
+ }
+ return E1000_SUCCESS;
+}
+
+/*****************************************************************************
+ * This function writes the buffer content at the offset given on the host if.
+ * It also does alignment considerations to do the writes in most efficient way.
+ * Also fills up the sum of the buffer in *buffer parameter.
+ *
+ * returns - E1000_SUCCESS for success.
+ ****************************************************************************/
+int32_t
+e1000_mng_host_if_write(struct e1000_hw * hw, uint8_t *buffer,
+ uint16_t length, uint16_t offset, uint8_t *sum)
+{
+ uint8_t *tmp;
+ uint8_t *bufptr = buffer;
+ uint32_t data;
+ uint16_t remaining, i, j, prev_bytes;
+
+ /* sum = only sum of the data and it is not checksum */
+
+ if (length == 0 || offset + length > E1000_HI_MAX_MNG_DATA_LENGTH) {
+ return -E1000_ERR_PARAM;
+ }
+
+ tmp = (uint8_t *)&data;
+ prev_bytes = offset & 0x3;
+ offset &= 0xFFFC;
+ offset >>= 2;
+
+ if (prev_bytes) {
+ data = E1000_READ_REG_ARRAY_DWORD(hw, HOST_IF, offset);
+ for (j = prev_bytes; j < sizeof(uint32_t); j++) {
+ *(tmp + j) = *bufptr++;
+ *sum += *(tmp + j);
+ }
+ E1000_WRITE_REG_ARRAY_DWORD(hw, HOST_IF, offset, data);
+ length -= j - prev_bytes;
+ offset++;
+ }
+
+ remaining = length & 0x3;
+ length -= remaining;
+
+ /* Calculate length in DWORDs */
+ length >>= 2;
+
+ /* The device driver writes the relevant command block into the
+ * ram area. */
+ for (i = 0; i < length; i++) {
+ for (j = 0; j < sizeof(uint32_t); j++) {
+ *(tmp + j) = *bufptr++;
+ *sum += *(tmp + j);
+ }
+
+ E1000_WRITE_REG_ARRAY_DWORD(hw, HOST_IF, offset + i, data);
+ }
+ if (remaining) {
+ for (j = 0; j < sizeof(uint32_t); j++) {
+ if (j < remaining)
+ *(tmp + j) = *bufptr++;
+ else
+ *(tmp + j) = 0;
+
+ *sum += *(tmp + j);
+ }
+ E1000_WRITE_REG_ARRAY_DWORD(hw, HOST_IF, offset + i, data);
+ }
+
+ return E1000_SUCCESS;
+}
+
+
+/*****************************************************************************
+ * This function writes the command header after does the checksum calculation.
+ *
+ * returns - E1000_SUCCESS for success.
+ ****************************************************************************/
+int32_t
+e1000_mng_write_cmd_header(struct e1000_hw * hw,
+ struct e1000_host_mng_command_header * hdr)
+{
+ uint16_t i;
+ uint8_t sum;
+ uint8_t *buffer;
+
+ /* Write the whole command header structure which includes sum of
+ * the buffer */
+
+ uint16_t length = sizeof(struct e1000_host_mng_command_header);
+
+ sum = hdr->checksum;
+ hdr->checksum = 0;
+
+ buffer = (uint8_t *) hdr;
+ i = length;
+ while(i--)
+ sum += buffer[i];
+
+ hdr->checksum = 0 - sum;
+
+ length >>= 2;
+ /* The device driver writes the relevant command block into the ram area. */
+ for (i = 0; i < length; i++)
+ E1000_WRITE_REG_ARRAY_DWORD(hw, HOST_IF, i, *((uint32_t *) hdr + i));
+
+ return E1000_SUCCESS;
+}
+
+
+/*****************************************************************************
+ * This function indicates to ARC that a new command is pending which completes
+ * one write operation by the driver.
+ *
+ * returns - E1000_SUCCESS for success.
+ ****************************************************************************/
+int32_t
+e1000_mng_write_commit(
+ struct e1000_hw * hw)
+{
+ uint32_t hicr;
+
+ hicr = E1000_READ_REG(hw, HICR);
+ /* Setting this bit tells the ARC that a new command is pending. */
+ E1000_WRITE_REG(hw, HICR, hicr | E1000_HICR_C);
+
+ return E1000_SUCCESS;
+}
+
+
+/*****************************************************************************
+ * This function checks the mode of the firmware.
+ *
+ * returns - TRUE when the mode is IAMT or FALSE.
+ ****************************************************************************/
+boolean_t
+e1000_check_mng_mode(
+ struct e1000_hw *hw)
+{
+ uint32_t fwsm;
+
+ fwsm = E1000_READ_REG(hw, FWSM);
+
+ if((fwsm & E1000_FWSM_MODE_MASK) ==
+ (E1000_MNG_IAMT_MODE << E1000_FWSM_MODE_SHIFT))
+ return TRUE;
+
+ return FALSE;
+}
+
+
+/*****************************************************************************
+ * This function writes the dhcp info .
+ ****************************************************************************/
+int32_t
+e1000_mng_write_dhcp_info(struct e1000_hw * hw, uint8_t *buffer,
+ uint16_t length)
+{
+ int32_t ret_val;
+ struct e1000_host_mng_command_header hdr;
+
+ hdr.command_id = E1000_MNG_DHCP_TX_PAYLOAD_CMD;
+ hdr.command_length = length;
+ hdr.reserved1 = 0;
+ hdr.reserved2 = 0;
+ hdr.checksum = 0;
+
+ ret_val = e1000_mng_enable_host_if(hw);
+ if (ret_val == E1000_SUCCESS) {
+ ret_val = e1000_mng_host_if_write(hw, buffer, length, sizeof(hdr),
+ &(hdr.checksum));
+ if (ret_val == E1000_SUCCESS) {
+ ret_val = e1000_mng_write_cmd_header(hw, &hdr);
+ if (ret_val == E1000_SUCCESS)
+ ret_val = e1000_mng_write_commit(hw);
+ }
+ }
+ return ret_val;
+}
+
+
+/*****************************************************************************
+ * This function calculates the checksum.
+ *
+ * returns - checksum of buffer contents.
+ ****************************************************************************/
+uint8_t
+e1000_calculate_mng_checksum(char *buffer, uint32_t length)
+{
+ uint8_t sum = 0;
+ uint32_t i;
+
+ if (!buffer)
+ return 0;
+
+ for (i=0; i < length; i++)
+ sum += buffer[i];
+
+ return (uint8_t) (0 - sum);
+}
+
+/*****************************************************************************
+ * This function checks whether tx pkt filtering needs to be enabled or not.
+ *
+ * returns - TRUE for packet filtering or FALSE.
+ ****************************************************************************/
+boolean_t
+e1000_enable_tx_pkt_filtering(struct e1000_hw *hw)
+{
+ /* called in init as well as watchdog timer functions */
+
+ int32_t ret_val, checksum;
+ boolean_t tx_filter = FALSE;
+ struct e1000_host_mng_dhcp_cookie *hdr = &(hw->mng_cookie);
+ uint8_t *buffer = (uint8_t *) &(hw->mng_cookie);
+
+ if (e1000_check_mng_mode(hw)) {
+ ret_val = e1000_mng_enable_host_if(hw);
+ if (ret_val == E1000_SUCCESS) {
+ ret_val = e1000_host_if_read_cookie(hw, buffer);
+ if (ret_val == E1000_SUCCESS) {
+ checksum = hdr->checksum;
+ hdr->checksum = 0;
+ if ((hdr->signature == E1000_IAMT_SIGNATURE) &&
+ checksum == e1000_calculate_mng_checksum((char *)buffer,
+ E1000_MNG_DHCP_COOKIE_LENGTH)) {
+ if (hdr->status &
+ E1000_MNG_DHCP_COOKIE_STATUS_PARSING_SUPPORT)
+ tx_filter = TRUE;
+ } else
+ tx_filter = TRUE;
+ } else
+ tx_filter = TRUE;
+ }
+ }
+
+ hw->tx_pkt_filtering = tx_filter;
+ return tx_filter;
+}
+
+/******************************************************************************
+ * Verifies the hardware needs to allow ARPs to be processed by the host
+ *
+ * hw - Struct containing variables accessed by shared code
+ *
+ * returns: - TRUE/FALSE
+ *
+ *****************************************************************************/
+uint32_t
+e1000_enable_mng_pass_thru(struct e1000_hw *hw)
+{
+ uint32_t manc;
+ uint32_t fwsm, factps;
+
+ if (hw->asf_firmware_present) {
+ manc = E1000_READ_REG(hw, MANC);
+
+ if (!(manc & E1000_MANC_RCV_TCO_EN) ||
+ !(manc & E1000_MANC_EN_MAC_ADDR_FILTER))
+ return FALSE;
+ if (e1000_arc_subsystem_valid(hw) == TRUE) {
+ fwsm = E1000_READ_REG(hw, FWSM);
+ factps = E1000_READ_REG(hw, FACTPS);
+
+ if (((fwsm & E1000_FWSM_MODE_MASK) ==
+ (e1000_mng_mode_pt << E1000_FWSM_MODE_SHIFT)) &&
+ (factps & E1000_FACTPS_MNGCG))
+ return TRUE;
+ } else
+ if ((manc & E1000_MANC_SMBUS_EN) && !(manc & E1000_MANC_ASF_EN))
+ return TRUE;
+ }
+ return FALSE;
+}
+
static int32_t
e1000_polarity_reversal_workaround(struct e1000_hw *hw)
{
@@ -5403,3 +6348,265 @@ e1000_polarity_reversal_workaround(struct e1000_hw *hw)
return E1000_SUCCESS;
}
+/***************************************************************************
+ *
+ * Disables PCI-Express master access.
+ *
+ * hw: Struct containing variables accessed by shared code
+ *
+ * returns: - none.
+ *
+ ***************************************************************************/
+void
+e1000_set_pci_express_master_disable(struct e1000_hw *hw)
+{
+ uint32_t ctrl;
+
+ DEBUGFUNC("e1000_set_pci_express_master_disable");
+
+ if (hw->bus_type != e1000_bus_type_pci_express)
+ return;
+
+ ctrl = E1000_READ_REG(hw, CTRL);
+ ctrl |= E1000_CTRL_GIO_MASTER_DISABLE;
+ E1000_WRITE_REG(hw, CTRL, ctrl);
+}
+
+/***************************************************************************
+ *
+ * Enables PCI-Express master access.
+ *
+ * hw: Struct containing variables accessed by shared code
+ *
+ * returns: - none.
+ *
+ ***************************************************************************/
+void
+e1000_enable_pciex_master(struct e1000_hw *hw)
+{
+ uint32_t ctrl;
+
+ DEBUGFUNC("e1000_enable_pciex_master");
+
+ if (hw->bus_type != e1000_bus_type_pci_express)
+ return;
+
+ ctrl = E1000_READ_REG(hw, CTRL);
+ ctrl &= ~E1000_CTRL_GIO_MASTER_DISABLE;
+ E1000_WRITE_REG(hw, CTRL, ctrl);
+}
+
+/*******************************************************************************
+ *
+ * Disables PCI-Express master access and verifies there are no pending requests
+ *
+ * hw: Struct containing variables accessed by shared code
+ *
+ * returns: - E1000_ERR_MASTER_REQUESTS_PENDING if master disable bit hasn't
+ * caused the master requests to be disabled.
+ * E1000_SUCCESS master requests disabled.
+ *
+ ******************************************************************************/
+int32_t
+e1000_disable_pciex_master(struct e1000_hw *hw)
+{
+ int32_t timeout = MASTER_DISABLE_TIMEOUT; /* 80ms */
+
+ DEBUGFUNC("e1000_disable_pciex_master");
+
+ if (hw->bus_type != e1000_bus_type_pci_express)
+ return E1000_SUCCESS;
+
+ e1000_set_pci_express_master_disable(hw);
+
+ while(timeout) {
+ if(!(E1000_READ_REG(hw, STATUS) & E1000_STATUS_GIO_MASTER_ENABLE))
+ break;
+ else
+ udelay(100);
+ timeout--;
+ }
+
+ if(!timeout) {
+ DEBUGOUT("Master requests are pending.\n");
+ return -E1000_ERR_MASTER_REQUESTS_PENDING;
+ }
+
+ return E1000_SUCCESS;
+}
+
+/*******************************************************************************
+ *
+ * Check for EEPROM Auto Read bit done.
+ *
+ * hw: Struct containing variables accessed by shared code
+ *
+ * returns: - E1000_ERR_RESET if fail to reset MAC
+ * E1000_SUCCESS at any other case.
+ *
+ ******************************************************************************/
+int32_t
+e1000_get_auto_rd_done(struct e1000_hw *hw)
+{
+ int32_t timeout = AUTO_READ_DONE_TIMEOUT;
+
+ DEBUGFUNC("e1000_get_auto_rd_done");
+
+ switch (hw->mac_type) {
+ default:
+ msec_delay(5);
+ break;
+ case e1000_82573:
+ while(timeout) {
+ if (E1000_READ_REG(hw, EECD) & E1000_EECD_AUTO_RD) break;
+ else msec_delay(1);
+ timeout--;
+ }
+
+ if(!timeout) {
+ DEBUGOUT("Auto read by HW from EEPROM has not completed.\n");
+ return -E1000_ERR_RESET;
+ }
+ break;
+ }
+
+ return E1000_SUCCESS;
+}
+
+/***************************************************************************
+ * Checks if the PHY configuration is done
+ *
+ * hw: Struct containing variables accessed by shared code
+ *
+ * returns: - E1000_ERR_RESET if fail to reset MAC
+ * E1000_SUCCESS at any other case.
+ *
+ ***************************************************************************/
+int32_t
+e1000_get_phy_cfg_done(struct e1000_hw *hw)
+{
+ DEBUGFUNC("e1000_get_phy_cfg_done");
+
+ /* Simply wait for 10ms */
+ msec_delay(10);
+
+ return E1000_SUCCESS;
+}
+
+/***************************************************************************
+ *
+ * Using the combination of SMBI and SWESMBI semaphore bits when resetting
+ * adapter or Eeprom access.
+ *
+ * hw: Struct containing variables accessed by shared code
+ *
+ * returns: - E1000_ERR_EEPROM if fail to access EEPROM.
+ * E1000_SUCCESS at any other case.
+ *
+ ***************************************************************************/
+int32_t
+e1000_get_hw_eeprom_semaphore(struct e1000_hw *hw)
+{
+ int32_t timeout;
+ uint32_t swsm;
+
+ DEBUGFUNC("e1000_get_hw_eeprom_semaphore");
+
+ if(!hw->eeprom_semaphore_present)
+ return E1000_SUCCESS;
+
+
+ /* Get the FW semaphore. */
+ timeout = hw->eeprom.word_size + 1;
+ while(timeout) {
+ swsm = E1000_READ_REG(hw, SWSM);
+ swsm |= E1000_SWSM_SWESMBI;
+ E1000_WRITE_REG(hw, SWSM, swsm);
+ /* if we managed to set the bit we got the semaphore. */
+ swsm = E1000_READ_REG(hw, SWSM);
+ if(swsm & E1000_SWSM_SWESMBI)
+ break;
+
+ udelay(50);
+ timeout--;
+ }
+
+ if(!timeout) {
+ /* Release semaphores */
+ e1000_put_hw_eeprom_semaphore(hw);
+ DEBUGOUT("Driver can't access the Eeprom - SWESMBI bit is set.\n");
+ return -E1000_ERR_EEPROM;
+ }
+
+ return E1000_SUCCESS;
+}
+
+/***************************************************************************
+ * This function clears HW semaphore bits.
+ *
+ * hw: Struct containing variables accessed by shared code
+ *
+ * returns: - None.
+ *
+ ***************************************************************************/
+void
+e1000_put_hw_eeprom_semaphore(struct e1000_hw *hw)
+{
+ uint32_t swsm;
+
+ DEBUGFUNC("e1000_put_hw_eeprom_semaphore");
+
+ if(!hw->eeprom_semaphore_present)
+ return;
+
+ swsm = E1000_READ_REG(hw, SWSM);
+ /* Release both semaphores. */
+ swsm &= ~(E1000_SWSM_SMBI | E1000_SWSM_SWESMBI);
+ E1000_WRITE_REG(hw, SWSM, swsm);
+}
+
+/******************************************************************************
+ * Checks if PHY reset is blocked due to SOL/IDER session, for example.
+ * Returning E1000_BLK_PHY_RESET isn't necessarily an error. But it's up to
+ * the caller to figure out how to deal with it.
+ *
+ * hw - Struct containing variables accessed by shared code
+ *
+ * returns: - E1000_BLK_PHY_RESET
+ * E1000_SUCCESS
+ *
+ *****************************************************************************/
+int32_t
+e1000_check_phy_reset_block(struct e1000_hw *hw)
+{
+ uint32_t manc = 0;
+ if(hw->mac_type > e1000_82547_rev_2)
+ manc = E1000_READ_REG(hw, MANC);
+ return (manc & E1000_MANC_BLK_PHY_RST_ON_IDE) ?
+ E1000_BLK_PHY_RESET : E1000_SUCCESS;
+}
+
+uint8_t
+e1000_arc_subsystem_valid(struct e1000_hw *hw)
+{
+ uint32_t fwsm;
+
+ /* On 8257x silicon, registers in the range of 0x8800 - 0x8FFC
+ * may not be provided a DMA clock when no manageability features are
+ * enabled. We do not want to perform any reads/writes to these registers
+ * if this is the case. We read FWSM to determine the manageability mode.
+ */
+ switch (hw->mac_type) {
+ case e1000_82573:
+ fwsm = E1000_READ_REG(hw, FWSM);
+ if((fwsm & E1000_FWSM_MODE_MASK) != 0)
+ return TRUE;
+ break;
+ default:
+ break;
+ }
+ return FALSE;
+}
+
+
+