summaryrefslogtreecommitdiff
path: root/drivers/net/usb/Kconfig
diff options
context:
space:
mode:
Diffstat (limited to 'drivers/net/usb/Kconfig')
-rw-r--r--drivers/net/usb/Kconfig338
1 files changed, 338 insertions, 0 deletions
diff --git a/drivers/net/usb/Kconfig b/drivers/net/usb/Kconfig
new file mode 100644
index 0000000..3de564b
--- /dev/null
+++ b/drivers/net/usb/Kconfig
@@ -0,0 +1,338 @@
+#
+# USB Network devices configuration
+#
+comment "Networking support is needed for USB Network Adapter support"
+ depends on USB && !NET
+
+menu "USB Network Adapters"
+ depends on USB && NET
+
+config USB_CATC
+ tristate "USB CATC NetMate-based Ethernet device support (EXPERIMENTAL)"
+ depends on EXPERIMENTAL
+ select CRC32
+ ---help---
+ Say Y if you want to use one of the following 10Mbps USB Ethernet
+ device based on the EL1210A chip. Supported devices are:
+ Belkin F5U011
+ Belkin F5U111
+ CATC NetMate
+ CATC NetMate II
+ smartBridges smartNIC
+
+ This driver makes the adapter appear as a normal Ethernet interface,
+ typically on eth0, if it is the only ethernet device, or perhaps on
+ eth1, if you have a PCI or ISA ethernet card installed.
+
+ To compile this driver as a module, choose M here: the
+ module will be called catc.
+
+config USB_KAWETH
+ tristate "USB KLSI KL5USB101-based ethernet device support"
+ ---help---
+ Say Y here if you want to use one of the following 10Mbps only
+ USB Ethernet adapters based on the KLSI KL5KUSB101B chipset:
+ 3Com 3C19250
+ ADS USB-10BT
+ ATEN USB Ethernet
+ ASANTE USB To Ethernet Adapter
+ AOX Endpoints USB Ethernet
+ Correga K.K.
+ D-Link DSB-650C and DU-E10
+ Entrega / Portgear E45
+ I-O DATA USB-ET/T
+ Jaton USB Ethernet Device Adapter
+ Kingston Technology USB Ethernet Adapter
+ Linksys USB10T
+ Mobility USB-Ethernet Adapter
+ NetGear EA-101
+ Peracom Enet and Enet2
+ Portsmith Express Ethernet Adapter
+ Shark Pocket Adapter
+ SMC 2202USB
+ Sony Vaio port extender
+
+ This driver is likely to work with most 10Mbps only USB Ethernet
+ adapters, including some "no brand" devices. It does NOT work on
+ SmartBridges smartNIC or on Belkin F5U111 devices - you should use
+ the CATC NetMate driver for those. If you are not sure which one
+ you need, select both, and the correct one should be selected for
+ you.
+
+ This driver makes the adapter appear as a normal Ethernet interface,
+ typically on eth0, if it is the only ethernet device, or perhaps on
+ eth1, if you have a PCI or ISA ethernet card installed.
+
+ To compile this driver as a module, choose M here: the
+ module will be called kaweth.
+
+config USB_PEGASUS
+ tristate "USB Pegasus/Pegasus-II based ethernet device support"
+ select MII
+ ---help---
+ Say Y here if you know you have Pegasus or Pegasus-II based adapter.
+ If in doubt then look at <file:drivers/usb/net/pegasus.h> for the
+ complete list of supported devices.
+
+ If your particular adapter is not in the list and you are _sure_ it
+ is Pegasus or Pegasus II based then send me
+ <petkan@users.sourceforge.net> vendor and device IDs.
+
+ To compile this driver as a module, choose M here: the
+ module will be called pegasus.
+
+config USB_RTL8150
+ tristate "USB RTL8150 based ethernet device support (EXPERIMENTAL)"
+ depends on EXPERIMENTAL
+ select MII
+ help
+ Say Y here if you have RTL8150 based usb-ethernet adapter.
+ Send me <petkan@users.sourceforge.net> any comments you may have.
+ You can also check for updates at <http://pegasus2.sourceforge.net/>.
+
+ To compile this driver as a module, choose M here: the
+ module will be called rtl8150.
+
+config USB_USBNET_MII
+ tristate
+ default n
+
+config USB_USBNET
+ tristate "Multi-purpose USB Networking Framework"
+ select MII if USB_USBNET_MII != n
+ ---help---
+ This driver supports several kinds of network links over USB,
+ with "minidrivers" built around a common network driver core
+ that supports deep queues for efficient transfers. (This gives
+ better performance with small packets and at high speeds).
+
+ The USB host runs "usbnet", and the other end of the link might be:
+
+ - Another USB host, when using USB "network" or "data transfer"
+ cables. These are often used to network laptops to PCs, like
+ "Laplink" parallel cables or some motherboards. These rely
+ on specialized chips from many suppliers.
+
+ - An intelligent USB gadget, perhaps embedding a Linux system.
+ These include PDAs running Linux (iPaq, Yopy, Zaurus, and
+ others), and devices that interoperate using the standard
+ CDC-Ethernet specification (including many cable modems).
+
+ - Network adapter hardware (like those for 10/100 Ethernet) which
+ uses this driver framework.
+
+ The link will appear with a name like "usb0", when the link is
+ a two-node link, or "eth0" for most CDC-Ethernet devices. Those
+ two-node links are most easily managed with Ethernet Bridging
+ (CONFIG_BRIDGE) instead of routing.
+
+ For more information see <http://www.linux-usb.org/usbnet/>.
+
+ To compile this driver as a module, choose M here: the
+ module will be called usbnet.
+
+config USB_NET_AX8817X
+ tristate "ASIX AX88xxx Based USB 2.0 Ethernet Adapters"
+ depends on USB_USBNET && NET_ETHERNET
+ select CRC32
+ select USB_USBNET_MII
+ default y
+ help
+ This option adds support for ASIX AX88xxx based USB 2.0
+ 10/100 Ethernet adapters.
+
+ This driver should work with at least the following devices:
+ * Aten UC210T
+ * ASIX AX88172
+ * Billionton Systems, USB2AR
+ * Buffalo LUA-U2-KTX
+ * Corega FEther USB2-TX
+ * D-Link DUB-E100
+ * Hawking UF200
+ * Linksys USB200M
+ * Netgear FA120
+ * Sitecom LN-029
+ * Intellinet USB 2.0 Ethernet
+ * ST Lab USB 2.0 Ethernet
+ * TrendNet TU2-ET100
+
+ This driver creates an interface named "ethX", where X depends on
+ what other networking devices you have in use.
+
+
+config USB_NET_CDCETHER
+ tristate "CDC Ethernet support (smart devices such as cable modems)"
+ depends on USB_USBNET
+ default y
+ help
+ This option supports devices conforming to the Communication Device
+ Class (CDC) Ethernet Control Model, a specification that's easy to
+ implement in device firmware. The CDC specifications are available
+ from <http://www.usb.org/>.
+
+ CDC Ethernet is an implementation option for DOCSIS cable modems
+ that support USB connectivity, used for non-Microsoft USB hosts.
+ The Linux-USB CDC Ethernet Gadget driver is an open implementation.
+ This driver should work with at least the following devices:
+
+ * Ericsson PipeRider (all variants)
+ * Motorola (DM100 and SB4100)
+ * Broadcom Cable Modem (reference design)
+ * Toshiba PCX1100U
+ * ...
+
+ This driver creates an interface named "ethX", where X depends on
+ what other networking devices you have in use. However, if the
+ IEEE 802 "local assignment" bit is set in the address, a "usbX"
+ name is used instead.
+
+config USB_NET_DM9601
+ tristate "Davicom DM9601 based USB 1.1 10/100 ethernet devices"
+ depends on USB_USBNET
+ select CRC32
+ select USB_USBNET_MII
+ help
+ This option adds support for Davicom DM9601 based USB 1.1
+ 10/100 Ethernet adapters.
+
+config USB_NET_GL620A
+ tristate "GeneSys GL620USB-A based cables"
+ depends on USB_USBNET
+ help
+ Choose this option if you're using a host-to-host cable,
+ or PC2PC motherboard, with this chip.
+
+ Note that the half-duplex "GL620USB" is not supported.
+
+config USB_NET_NET1080
+ tristate "NetChip 1080 based cables (Laplink, ...)"
+ default y
+ depends on USB_USBNET
+ help
+ Choose this option if you're using a host-to-host cable based
+ on this design: one NetChip 1080 chip and supporting logic,
+ optionally with LEDs that indicate traffic
+
+config USB_NET_PLUSB
+ tristate "Prolific PL-2301/2302 based cables"
+ # if the handshake/init/reset problems, from original 'plusb',
+ # are ever resolved ... then remove "experimental"
+ depends on USB_USBNET && EXPERIMENTAL
+ help
+ Choose this option if you're using a host-to-host cable
+ with one of these chips.
+
+config USB_NET_MCS7830
+ tristate "MosChip MCS7830 based Ethernet adapters"
+ depends on USB_USBNET
+ select USB_USBNET_MII
+ help
+ Choose this option if you're using a 10/100 Ethernet USB2
+ adapter based on the MosChip 7830 controller. This includes
+ adapters marketed under the DeLOCK brand.
+
+config USB_NET_RNDIS_HOST
+ tristate "Host for RNDIS and ActiveSync devices (EXPERIMENTAL)"
+ depends on USB_USBNET && EXPERIMENTAL
+ select USB_NET_CDCETHER
+ help
+ This option enables hosting "Remote NDIS" USB networking links,
+ as encouraged by Microsoft (instead of CDC Ethernet!) for use in
+ various devices that may only support this protocol. A variant
+ of this protocol (with even less public documentation) seems to
+ be at the root of Microsoft's "ActiveSync" too.
+
+ Avoid using this protocol unless you have no better options.
+ The protocol specification is incomplete, and is controlled by
+ (and for) Microsoft; it isn't an "Open" ecosystem or market.
+
+config USB_NET_CDC_SUBSET
+ tristate "Simple USB Network Links (CDC Ethernet subset)"
+ depends on USB_USBNET
+ default y
+ help
+ This driver module supports USB network devices that can work
+ without any device-specific information. Select it if you have
+ one of these drivers.
+
+ Note that while many USB host-to-host cables can work in this mode,
+ that may mean not being able to talk to Win32 systems or more
+ commonly not being able to handle certain events (like replugging
+ the host on the other end) very well. Also, these devices will
+ not generally have permanently assigned Ethernet addresses.
+
+config USB_ALI_M5632
+ boolean "ALi M5632 based 'USB 2.0 Data Link' cables"
+ depends on USB_NET_CDC_SUBSET
+ help
+ Choose this option if you're using a host-to-host cable
+ based on this design, which supports USB 2.0 high speed.
+
+config USB_AN2720
+ boolean "AnchorChips 2720 based cables (Xircom PGUNET, ...)"
+ depends on USB_NET_CDC_SUBSET
+ help
+ Choose this option if you're using a host-to-host cable
+ based on this design. Note that AnchorChips is now a
+ Cypress brand.
+
+config USB_BELKIN
+ boolean "eTEK based host-to-host cables (Advance, Belkin, ...)"
+ depends on USB_NET_CDC_SUBSET
+ default y
+ help
+ Choose this option if you're using a host-to-host cable
+ based on this design: two NetChip 2890 chips and an Atmel
+ microcontroller, with LEDs that indicate traffic.
+
+config USB_ARMLINUX
+ boolean "Embedded ARM Linux links (iPaq, ...)"
+ depends on USB_NET_CDC_SUBSET
+ default y
+ help
+ Choose this option to support the "usb-eth" networking driver
+ used by most of the ARM Linux community with device controllers
+ such as the SA-11x0 and PXA-25x UDCs, or the tftp capabilities
+ in some PXA versions of the "blob" boot loader.
+
+ Linux-based "Gumstix" PXA-25x based systems use this protocol
+ to talk with other Linux systems.
+
+ Although the ROMs shipped with Sharp Zaurus products use a
+ different link level framing protocol, you can have them use
+ this simpler protocol by installing a different kernel.
+
+config USB_EPSON2888
+ boolean "Epson 2888 based firmware (DEVELOPMENT)"
+ depends on USB_NET_CDC_SUBSET
+ help
+ Choose this option to support the usb networking links used
+ by some sample firmware from Epson.
+
+config USB_KC2190
+ boolean "KT Technology KC2190 based cables (InstaNet)"
+ depends on USB_NET_CDC_SUBSET && EXPERIMENTAL
+ help
+  Choose this option if you're using a host-to-host cable
+  with one of these chips.
+
+config USB_NET_ZAURUS
+ tristate "Sharp Zaurus (stock ROMs) and compatible"
+ depends on USB_USBNET
+ select USB_NET_CDCETHER
+ select CRC32
+ default y
+ help
+ Choose this option to support the usb networking links used by
+ Zaurus models like the SL-5000D, SL-5500, SL-5600, A-300, B-500.
+ This also supports some related device firmware, as used in some
+ PDAs from Olympus and some cell phones from Motorola.
+
+ If you install an alternate image, such as the Linux 2.6 based
+ versions of OpenZaurus, you should no longer need to support this
+ protocol. Only the "eth-fd" or "net_fd" drivers in these devices
+ really need this non-conformant variant of CDC Ethernet (or in
+ some cases CDC MDLM) protocol, not "g_ether".
+
+
+endmenu