diff options
Diffstat (limited to 'drivers/pci')
| -rw-r--r-- | drivers/pci/host/pci-imx6.c | 47 |
1 files changed, 34 insertions, 13 deletions
diff --git a/drivers/pci/host/pci-imx6.c b/drivers/pci/host/pci-imx6.c index e8663a8..ee08250 100644 --- a/drivers/pci/host/pci-imx6.c +++ b/drivers/pci/host/pci-imx6.c @@ -424,20 +424,40 @@ static void imx6_pcie_reset_phy(struct pcie_port *pp) static int imx6_pcie_link_up(struct pcie_port *pp) { - u32 rc, ltssm, rx_valid; + u32 rc, debug_r0, rx_valid; + int count = 5; /* - * Test if the PHY reports that the link is up and also that - * the link training finished. It might happen that the PHY - * reports the link is already up, but the link training bit - * is still set, so make sure to check the training is done - * as well here. + * Test if the PHY reports that the link is up and also that the LTSSM + * training finished. There are three possible states of the link when + * this code is called: + * 1) The link is DOWN (unlikely) + * The link didn't come up yet for some reason. This usually means + * we have a real problem somewhere. Reset the PHY and exit. This + * state calls for inspection of the DEBUG registers. + * 2) The link is UP, but still in LTSSM training + * Wait for the training to finish, which should take a very short + * time. If the training does not finish, we have a problem and we + * need to inspect the DEBUG registers. If the training does finish, + * the link is up and operating correctly. + * 3) The link is UP and no longer in LTSSM training + * The link is up and operating correctly. */ - rc = readl(pp->dbi_base + PCIE_PHY_DEBUG_R1); - if ((rc & PCIE_PHY_DEBUG_R1_XMLH_LINK_UP) && - !(rc & PCIE_PHY_DEBUG_R1_XMLH_LINK_IN_TRAINING)) - return 1; - + while (1) { + rc = readl(pp->dbi_base + PCIE_PHY_DEBUG_R1); + if (!(rc & PCIE_PHY_DEBUG_R1_XMLH_LINK_UP)) + break; + if (!(rc & PCIE_PHY_DEBUG_R1_XMLH_LINK_IN_TRAINING)) + return 1; + if (!count--) + break; + dev_dbg(pp->dev, "Link is up, but still in training\n"); + /* + * Wait a little bit, then re-check if the link finished + * the training. + */ + usleep_range(1000, 2000); + } /* * From L0, initiate MAC entry to gen2 if EP/RC supports gen2. * Wait 2ms (LTSSM timeout is 24ms, PHY lock is ~5us in gen2). @@ -446,15 +466,16 @@ static int imx6_pcie_link_up(struct pcie_port *pp) * to gen2 is stuck */ pcie_phy_read(pp->dbi_base, PCIE_PHY_RX_ASIC_OUT, &rx_valid); - ltssm = readl(pp->dbi_base + PCIE_PHY_DEBUG_R0) & 0x3F; + debug_r0 = readl(pp->dbi_base + PCIE_PHY_DEBUG_R0); if (rx_valid & 0x01) return 0; - if (ltssm != 0x0d) + if ((debug_r0 & 0x3f) != 0x0d) return 0; dev_err(pp->dev, "transition to gen2 is stuck, reset PHY!\n"); + dev_dbg(pp->dev, "debug_r0=%08x debug_r1=%08x\n", debug_r0, rc); imx6_pcie_reset_phy(pp); |