diff options
Diffstat (limited to 'drivers/regulator')
28 files changed, 3981 insertions, 735 deletions
diff --git a/drivers/regulator/Kconfig b/drivers/regulator/Kconfig index 2dc8289..55d7b7b 100644 --- a/drivers/regulator/Kconfig +++ b/drivers/regulator/Kconfig @@ -199,13 +199,14 @@ config REGULATOR_DA9210 interface. config REGULATOR_DA9211 - tristate "Dialog Semiconductor DA9211/DA9212 regulator" + tristate "Dialog Semiconductor DA9211/DA9212/DA9213/DA9214 regulator" depends on I2C select REGMAP_I2C help - Say y here to support for the Dialog Semiconductor DA9211/DA9212. - The DA9211/DA9212 is a multi-phase synchronous step down - converter 12A DC-DC Buck controlled through an I2C + Say y here to support for the Dialog Semiconductor DA9211/DA9212 + /DA9213/DA9214. + The DA9211/DA9212/DA9213/DA9214 is a multi-phase synchronous + step down converter 12A or 16A DC-DC Buck controlled through an I2C interface. config REGULATOR_DBX500_PRCMU @@ -240,6 +241,23 @@ config REGULATOR_GPIO and the platform has to provide a mapping of GPIO-states to target volts/amps. +config REGULATOR_HI6421 + tristate "HiSilicon Hi6421 PMIC voltage regulator support" + depends on MFD_HI6421_PMIC && OF + help + This driver provides support for the voltage regulators on the + HiSilicon Hi6421 PMU / Codec IC. + Hi6421 is a multi-function device which, on regulator part, provides + 21 general purpose LDOs, 3 dedicated LDOs, and 5 BUCKs. All + of them come with support to either ECO (idle) or sleep mode. + +config REGULATOR_ISL9305 + tristate "Intersil ISL9305 regulator" + depends on I2C + select REGMAP_I2C + help + This driver supports ISL9305 voltage regulator chip. + config REGULATOR_ISL6271A tristate "Intersil ISL6271A Power regulator" depends on I2C @@ -387,6 +405,15 @@ config REGULATOR_MAX77693 and one current regulator 'CHARGER'. This is suitable for Exynos-4x12 chips. +config REGULATOR_MAX77802 + tristate "Maxim 77802 regulator" + depends on MFD_MAX77686 + help + This driver controls a Maxim 77802 regulator + via I2C bus. The provided regulator is suitable for + Exynos5420/Exynos5800 SoCs to control various voltages. + It includes support for control of voltage and ramp speed. + config REGULATOR_MC13XXX_CORE tristate @@ -449,6 +476,25 @@ config REGULATOR_PFUZE100 Say y here to support the regulators found on the Freescale PFUZE100/PFUZE200 PMIC. +config REGULATOR_PWM + tristate "PWM voltage regulator" + depends on PWM + help + This driver supports PWM controlled voltage regulators. PWM + duty cycle can increase or decrease the voltage. + +config REGULATOR_QCOM_RPM + tristate "Qualcomm RPM regulator driver" + depends on MFD_QCOM_RPM + help + If you say yes to this option, support will be included for the + regulators exposed by the Resource Power Manager found in Qualcomm + 8660, 8960 and 8064 based devices. + + Say M here if you want to include support for the regulators on the + Qualcomm RPM as a module. The module will be named + "qcom_rpm-regulator". + config REGULATOR_RC5T583 tristate "RICOH RC5T583 Power regulators" depends on MFD_RC5T583 @@ -459,6 +505,22 @@ config REGULATOR_RC5T583 through regulator interface. The device supports multiple DCDC/LDO outputs which can be controlled by i2c communication. +config REGULATOR_RK808 + tristate "Rockchip RK808 Power regulators" + depends on MFD_RK808 + help + Select this option to enable the power regulator of ROCKCHIP + PMIC RK808. + This driver supports the control of different power rails of device + through regulator interface. The device supports multiple DCDC/LDO + outputs which can be controlled by i2c communication. + +config REGULATOR_RN5T618 + tristate "Ricoh RN5T618 voltage regulators" + depends on MFD_RN5T618 + help + Say y here to support the regulators found on Ricoh RN5T618 PMIC. + config REGULATOR_S2MPA01 tristate "Samsung S2MPA01 voltage regulator" depends on MFD_SEC_CORE @@ -483,11 +545,16 @@ config REGULATOR_S5M8767 via I2C bus. S5M8767A have 9 Bucks and 28 LDOs output and supports DVS mode with 8bits of output voltage control. -config REGULATOR_ST_PWM - tristate "STMicroelectronics PWM voltage regulator" - depends on ARCH_STI +config REGULATOR_SKY81452 + tristate "Skyworks Solutions SKY81452 voltage regulator" + depends on SKY81452 help - This driver supports ST's PWM controlled voltage regulators. + This driver supports Skyworks SKY81452 voltage output regulator + via I2C bus. SKY81452 has one voltage linear regulator can be + programmed from 4.5V to 20V. + + This driver can also be built as a module. If so, the module + will be called sky81452-regulator. config REGULATOR_TI_ABB tristate "TI Adaptive Body Bias on-chip LDO" diff --git a/drivers/regulator/Makefile b/drivers/regulator/Makefile index aa4a6aa..1029ed3 100644 --- a/drivers/regulator/Makefile +++ b/drivers/regulator/Makefile @@ -32,7 +32,9 @@ obj-$(CONFIG_REGULATOR_DBX500_PRCMU) += dbx500-prcmu.o obj-$(CONFIG_REGULATOR_DB8500_PRCMU) += db8500-prcmu.o obj-$(CONFIG_REGULATOR_FAN53555) += fan53555.o obj-$(CONFIG_REGULATOR_GPIO) += gpio-regulator.o +obj-$(CONFIG_REGULATOR_HI6421) += hi6421-regulator.o obj-$(CONFIG_REGULATOR_ISL6271A) += isl6271a-regulator.o +obj-$(CONFIG_REGULATOR_ISL9305) += isl9305.o obj-$(CONFIG_REGULATOR_LP3971) += lp3971.o obj-$(CONFIG_REGULATOR_LP3972) += lp3972.o obj-$(CONFIG_REGULATOR_LP872X) += lp872x.o @@ -52,20 +54,25 @@ obj-$(CONFIG_REGULATOR_MAX8997) += max8997.o obj-$(CONFIG_REGULATOR_MAX8998) += max8998.o obj-$(CONFIG_REGULATOR_MAX77686) += max77686.o obj-$(CONFIG_REGULATOR_MAX77693) += max77693.o +obj-$(CONFIG_REGULATOR_MAX77802) += max77802.o obj-$(CONFIG_REGULATOR_MC13783) += mc13783-regulator.o obj-$(CONFIG_REGULATOR_MC13892) += mc13892-regulator.o obj-$(CONFIG_REGULATOR_MC13XXX_CORE) += mc13xxx-regulator-core.o +obj-$(CONFIG_REGULATOR_QCOM_RPM) += qcom_rpm-regulator.o obj-$(CONFIG_REGULATOR_PALMAS) += palmas-regulator.o obj-$(CONFIG_REGULATOR_PFUZE100) += pfuze100-regulator.o +obj-$(CONFIG_REGULATOR_PWM) += pwm-regulator.o obj-$(CONFIG_REGULATOR_TPS51632) += tps51632-regulator.o obj-$(CONFIG_REGULATOR_PBIAS) += pbias-regulator.o obj-$(CONFIG_REGULATOR_PCAP) += pcap-regulator.o obj-$(CONFIG_REGULATOR_PCF50633) += pcf50633-regulator.o obj-$(CONFIG_REGULATOR_RC5T583) += rc5t583-regulator.o +obj-$(CONFIG_REGULATOR_RK808) += rk808-regulator.o +obj-$(CONFIG_REGULATOR_RN5T618) += rn5t618-regulator.o obj-$(CONFIG_REGULATOR_S2MPA01) += s2mpa01.o obj-$(CONFIG_REGULATOR_S2MPS11) += s2mps11.o obj-$(CONFIG_REGULATOR_S5M8767) += s5m8767.o -obj-$(CONFIG_REGULATOR_ST_PWM) += st-pwm.o +obj-$(CONFIG_REGULATOR_SKY81452) += sky81452-regulator.o obj-$(CONFIG_REGULATOR_STW481X_VMMC) += stw481x-vmmc.o obj-$(CONFIG_REGULATOR_TI_ABB) += ti-abb-regulator.o obj-$(CONFIG_REGULATOR_TPS6105X) += tps6105x-regulator.o diff --git a/drivers/regulator/as3711-regulator.c b/drivers/regulator/as3711-regulator.c index b47283f..8459b0b 100644 --- a/drivers/regulator/as3711-regulator.c +++ b/drivers/regulator/as3711-regulator.c @@ -22,12 +22,10 @@ struct as3711_regulator_info { struct regulator_desc desc; - unsigned int max_uV; }; struct as3711_regulator { struct as3711_regulator_info *reg_info; - struct regulator_dev *rdev; }; /* @@ -132,39 +130,37 @@ static const struct regulator_linear_range as3711_dldo_ranges[] = { REGULATOR_LINEAR_RANGE(1750000, 0x20, 0x3f, 50000), }; -#define AS3711_REG(_id, _en_reg, _en_bit, _vmask, _vshift, _min_uV, _max_uV, _sfx) \ - [AS3711_REGULATOR_ ## _id] = { \ - .desc = { \ - .name = "as3711-regulator-" # _id, \ - .id = AS3711_REGULATOR_ ## _id, \ - .n_voltages = (_vmask + 1), \ - .ops = &as3711_ ## _sfx ## _ops, \ - .type = REGULATOR_VOLTAGE, \ - .owner = THIS_MODULE, \ - .vsel_reg = AS3711_ ## _id ## _VOLTAGE, \ - .vsel_mask = _vmask << _vshift, \ - .enable_reg = AS3711_ ## _en_reg, \ - .enable_mask = BIT(_en_bit), \ - .min_uV = _min_uV, \ - .linear_ranges = as3711_ ## _sfx ## _ranges, \ - .n_linear_ranges = ARRAY_SIZE(as3711_ ## _sfx ## _ranges), \ - }, \ - .max_uV = _max_uV, \ +#define AS3711_REG(_id, _en_reg, _en_bit, _vmask, _sfx) \ + [AS3711_REGULATOR_ ## _id] = { \ + .desc = { \ + .name = "as3711-regulator-" # _id, \ + .id = AS3711_REGULATOR_ ## _id, \ + .n_voltages = (_vmask + 1), \ + .ops = &as3711_ ## _sfx ## _ops, \ + .type = REGULATOR_VOLTAGE, \ + .owner = THIS_MODULE, \ + .vsel_reg = AS3711_ ## _id ## _VOLTAGE, \ + .vsel_mask = _vmask, \ + .enable_reg = AS3711_ ## _en_reg, \ + .enable_mask = BIT(_en_bit), \ + .linear_ranges = as3711_ ## _sfx ## _ranges, \ + .n_linear_ranges = ARRAY_SIZE(as3711_ ## _sfx ## _ranges), \ + }, \ } static struct as3711_regulator_info as3711_reg_info[] = { - AS3711_REG(SD_1, SD_CONTROL, 0, 0x7f, 0, 612500, 3350000, sd), - AS3711_REG(SD_2, SD_CONTROL, 1, 0x7f, 0, 612500, 3350000, sd), - AS3711_REG(SD_3, SD_CONTROL, 2, 0x7f, 0, 612500, 3350000, sd), - AS3711_REG(SD_4, SD_CONTROL, 3, 0x7f, 0, 612500, 3350000, sd), - AS3711_REG(LDO_1, LDO_1_VOLTAGE, 7, 0x1f, 0, 1200000, 3300000, aldo), - AS3711_REG(LDO_2, LDO_2_VOLTAGE, 7, 0x1f, 0, 1200000, 3300000, aldo), - AS3711_REG(LDO_3, LDO_3_VOLTAGE, 7, 0x3f, 0, 900000, 3300000, dldo), - AS3711_REG(LDO_4, LDO_4_VOLTAGE, 7, 0x3f, 0, 900000, 3300000, dldo), - AS3711_REG(LDO_5, LDO_5_VOLTAGE, 7, 0x3f, 0, 900000, 3300000, dldo), - AS3711_REG(LDO_6, LDO_6_VOLTAGE, 7, 0x3f, 0, 900000, 3300000, dldo), - AS3711_REG(LDO_7, LDO_7_VOLTAGE, 7, 0x3f, 0, 900000, 3300000, dldo), - AS3711_REG(LDO_8, LDO_8_VOLTAGE, 7, 0x3f, 0, 900000, 3300000, dldo), + AS3711_REG(SD_1, SD_CONTROL, 0, 0x7f, sd), + AS3711_REG(SD_2, SD_CONTROL, 1, 0x7f, sd), + AS3711_REG(SD_3, SD_CONTROL, 2, 0x7f, sd), + AS3711_REG(SD_4, SD_CONTROL, 3, 0x7f, sd), + AS3711_REG(LDO_1, LDO_1_VOLTAGE, 7, 0x1f, aldo), + AS3711_REG(LDO_2, LDO_2_VOLTAGE, 7, 0x1f, aldo), + AS3711_REG(LDO_3, LDO_3_VOLTAGE, 7, 0x3f, dldo), + AS3711_REG(LDO_4, LDO_4_VOLTAGE, 7, 0x3f, dldo), + AS3711_REG(LDO_5, LDO_5_VOLTAGE, 7, 0x3f, dldo), + AS3711_REG(LDO_6, LDO_6_VOLTAGE, 7, 0x3f, dldo), + AS3711_REG(LDO_7, LDO_7_VOLTAGE, 7, 0x3f, dldo), + AS3711_REG(LDO_8, LDO_8_VOLTAGE, 7, 0x3f, dldo), /* StepUp output voltage depends on supplying regulator */ }; @@ -263,7 +259,6 @@ static int as3711_regulator_probe(struct platform_device *pdev) ri->desc.name); return PTR_ERR(rdev); } - reg->rdev = rdev; } platform_set_drvdata(pdev, regs); return 0; diff --git a/drivers/regulator/axp20x-regulator.c b/drivers/regulator/axp20x-regulator.c index 004aadb..2e1010a 100644 --- a/drivers/regulator/axp20x-regulator.c +++ b/drivers/regulator/axp20x-regulator.c @@ -245,7 +245,7 @@ static int axp20x_regulator_probe(struct platform_device *pdev) for (i = 0; i < AXP20X_REG_ID_MAX; i++) { init_data = axp20x_matches[i].init_data; - config.dev = &pdev->dev; + config.dev = pdev->dev.parent; config.init_data = init_data; config.regmap = axp20x->regmap; config.of_node = axp20x_matches[i].of_node; diff --git a/drivers/regulator/bcm590xx-regulator.c b/drivers/regulator/bcm590xx-regulator.c index 5d1fd6f..fe6ac69 100644 --- a/drivers/regulator/bcm590xx-regulator.c +++ b/drivers/regulator/bcm590xx-regulator.c @@ -202,7 +202,6 @@ static struct bcm590xx_info bcm590xx_regs[] = { struct bcm590xx_reg { struct regulator_desc *desc; struct bcm590xx *mfd; - struct bcm590xx_info **info; }; static int bcm590xx_get_vsel_register(int id) @@ -389,11 +388,6 @@ static int bcm590xx_probe(struct platform_device *pdev) if (!pmu->desc) return -ENOMEM; - pmu->info = devm_kzalloc(&pdev->dev, BCM590XX_NUM_REGS * - sizeof(struct bcm590xx_info *), GFP_KERNEL); - if (!pmu->info) - return -ENOMEM; - info = bcm590xx_regs; for (i = 0; i < BCM590XX_NUM_REGS; i++, info++) { @@ -403,8 +397,6 @@ static int bcm590xx_probe(struct platform_device *pdev) reg_data = NULL; /* Register the regulators */ - pmu->info[i] = info; - pmu->desc[i].name = info->name; pmu->desc[i].supply_name = info->vin_name; pmu->desc[i].id = i; diff --git a/drivers/regulator/core.c b/drivers/regulator/core.c index a3c3785..cd87c0c 100644 --- a/drivers/regulator/core.c +++ b/drivers/regulator/core.c @@ -102,7 +102,7 @@ static int _regulator_disable(struct regulator_dev *rdev); static int _regulator_get_voltage(struct regulator_dev *rdev); static int _regulator_get_current_limit(struct regulator_dev *rdev); static unsigned int _regulator_get_mode(struct regulator_dev *rdev); -static void _notifier_call_chain(struct regulator_dev *rdev, +static int _notifier_call_chain(struct regulator_dev *rdev, unsigned long event, void *data); static int _regulator_do_set_voltage(struct regulator_dev *rdev, int min_uV, int max_uV); @@ -839,7 +839,7 @@ static void print_constraints(struct regulator_dev *rdev) static int machine_constraints_voltage(struct regulator_dev *rdev, struct regulation_constraints *constraints) { - struct regulator_ops *ops = rdev->desc->ops; + const struct regulator_ops *ops = rdev->desc->ops; int ret; /* do we need to apply the constraint voltage */ @@ -938,7 +938,7 @@ static int machine_constraints_voltage(struct regulator_dev *rdev, static int machine_constraints_current(struct regulator_dev *rdev, struct regulation_constraints *constraints) { - struct regulator_ops *ops = rdev->desc->ops; + const struct regulator_ops *ops = rdev->desc->ops; int ret; if (!constraints->min_uA && !constraints->max_uA) @@ -982,7 +982,7 @@ static int set_machine_constraints(struct regulator_dev *rdev, const struct regulation_constraints *constraints) { int ret = 0; - struct regulator_ops *ops = rdev->desc->ops; + const struct regulator_ops *ops = rdev->desc->ops; if (constraints) rdev->constraints = kmemdup(constraints, sizeof(*constraints), @@ -1759,6 +1759,45 @@ static int regulator_ena_gpio_ctrl(struct regulator_dev *rdev, bool enable) return 0; } +/** + * _regulator_enable_delay - a delay helper function + * @delay: time to delay in microseconds + * + * Delay for the requested amount of time as per the guidelines in: + * + * Documentation/timers/timers-howto.txt + * + * The assumption here is that regulators will never be enabled in + * atomic context and therefore sleeping functions can be used. + */ +static void _regulator_enable_delay(unsigned int delay) +{ + unsigned int ms = delay / 1000; + unsigned int us = delay % 1000; + + if (ms > 0) { + /* + * For small enough values, handle super-millisecond + * delays in the usleep_range() call below. + */ + if (ms < 20) + us += ms * 1000; + else + msleep(ms); + } + + /* + * Give the scheduler some room to coalesce with any other + * wakeup sources. For delays shorter than 10 us, don't even + * bother setting up high-resolution timers and just busy- + * loop. + */ + if (us >= 10) + usleep_range(us, us + 100); + else + udelay(us); +} + static int _regulator_do_enable(struct regulator_dev *rdev) { int ret, delay; @@ -1774,6 +1813,31 @@ static int _regulator_do_enable(struct regulator_dev *rdev) trace_regulator_enable(rdev_get_name(rdev)); + if (rdev->desc->off_on_delay) { + /* if needed, keep a distance of off_on_delay from last time + * this regulator was disabled. + */ + unsigned long start_jiffy = jiffies; + unsigned long intended, max_delay, remaining; + + max_delay = usecs_to_jiffies(rdev->desc->off_on_delay); + intended = rdev->last_off_jiffy + max_delay; + + if (time_before(start_jiffy, intended)) { + /* calc remaining jiffies to deal with one-time + * timer wrapping. + * in case of multiple timer wrapping, either it can be + * detected by out-of-range remaining, or it cannot be + * detected and we gets a panelty of + * _regulator_enable_delay(). + */ + remaining = intended - start_jiffy; + if (remaining <= max_delay) + _regulator_enable_delay( + jiffies_to_usecs(remaining)); + } + } + if (rdev->ena_pin) { ret = regulator_ena_gpio_ctrl(rdev, true); if (ret < 0) @@ -1792,40 +1856,7 @@ static int _regulator_do_enable(struct regulator_dev *rdev) * together. */ trace_regulator_enable_delay(rdev_get_name(rdev)); - /* - * Delay for the requested amount of time as per the guidelines in: - * - * Documentation/timers/timers-howto.txt - * - * The assumption here is that regulators will never be enabled in - * atomic context and therefore sleeping functions can be used. - */ - if (delay) { - unsigned int ms = delay / 1000; - unsigned int us = delay % 1000; - - if (ms > 0) { - /* - * For small enough values, handle super-millisecond - * delays in the usleep_range() call below. - */ - if (ms < 20) - us += ms * 1000; - else - msleep(ms); - } - - /* - * Give the scheduler some room to coalesce with any other - * wakeup sources. For delays shorter than 10 us, don't even - * bother setting up high-resolution timers and just busy- - * loop. - */ - if (us >= 10) - usleep_range(us, us + 100); - else - udelay(us); - } + _regulator_enable_delay(delay); trace_regulator_enable_complete(rdev_get_name(rdev)); @@ -1919,6 +1950,12 @@ static int _regulator_do_disable(struct regulator_dev *rdev) return ret; } + /* cares about last_off_jiffy only if off_on_delay is required by + * device. + */ + if (rdev->desc->off_on_delay) + rdev->last_off_jiffy = jiffies; + trace_regulator_disable_complete(rdev_get_name(rdev)); return 0; @@ -2208,9 +2245,9 @@ EXPORT_SYMBOL_GPL(regulator_count_voltages); */ int regulator_list_voltage(struct regulator *regulator, unsigned selector) { - struct regulator_dev *rdev = regulator->rdev; - struct regulator_ops *ops = rdev->desc->ops; - int ret; + struct regulator_dev *rdev = regulator->rdev; + const struct regulator_ops *ops = rdev->desc->ops; + int ret; if (rdev->desc->fixed_uV && rdev->desc->n_voltages == 1 && !selector) return rdev->desc->fixed_uV; @@ -2270,8 +2307,8 @@ int regulator_get_hardware_vsel_register(struct regulator *regulator, unsigned *vsel_reg, unsigned *vsel_mask) { - struct regulator_dev *rdev = regulator->rdev; - struct regulator_ops *ops = rdev->desc->ops; + struct regulator_dev *rdev = regulator->rdev; + const struct regulator_ops *ops = rdev->desc->ops; if (ops->set_voltage_sel != regulator_set_voltage_sel_regmap) return -EOPNOTSUPP; @@ -2297,8 +2334,8 @@ EXPORT_SYMBOL_GPL(regulator_get_hardware_vsel_register); int regulator_list_hardware_vsel(struct regulator *regulator, unsigned selector) { - struct regulator_dev *rdev = regulator->rdev; - struct regulator_ops *ops = rdev->desc->ops; + struct regulator_dev *rdev = regulator->rdev; + const struct regulator_ops *ops = rdev->desc->ops; if (selector >= rdev->desc->n_voltages) return -EINVAL; @@ -2369,6 +2406,55 @@ int regulator_is_supported_voltage(struct regulator *regulator, } EXPORT_SYMBOL_GPL(regulator_is_supported_voltage); +static int _regulator_call_set_voltage(struct regulator_dev *rdev, + int min_uV, int max_uV, + unsigned *selector) +{ + struct pre_voltage_change_data data; + int ret; + + data.old_uV = _regulator_get_voltage(rdev); + data.min_uV = min_uV; + data.max_uV = max_uV; + ret = _notifier_call_chain(rdev, REGULATOR_EVENT_PRE_VOLTAGE_CHANGE, + &data); + if (ret & NOTIFY_STOP_MASK) + return -EINVAL; + + ret = rdev->desc->ops->set_voltage(rdev, min_uV, max_uV, selector); + if (ret >= 0) + return ret; + + _notifier_call_chain(rdev, REGULATOR_EVENT_ABORT_VOLTAGE_CHANGE, + (void *)data.old_uV); + + return ret; +} + +static int _regulator_call_set_voltage_sel(struct regulator_dev *rdev, + int uV, unsigned selector) +{ + struct pre_voltage_change_data data; + int ret; + + data.old_uV = _regulator_get_voltage(rdev); + data.min_uV = uV; + data.max_uV = uV; + ret = _notifier_call_chain(rdev, REGULATOR_EVENT_PRE_VOLTAGE_CHANGE, + &data); + if (ret & NOTIFY_STOP_MASK) + return -EINVAL; + + ret = rdev->desc->ops->set_voltage_sel(rdev, selector); + if (ret >= 0) + return ret; + + _notifier_call_chain(rdev, REGULATOR_EVENT_ABORT_VOLTAGE_CHANGE, + (void *)data.old_uV); + + return ret; +} + static int _regulator_do_set_voltage(struct regulator_dev *rdev, int min_uV, int max_uV) { @@ -2396,8 +2482,8 @@ static int _regulator_do_set_voltage(struct regulator_dev *rdev, } if (rdev->desc->ops->set_voltage) { - ret = rdev->desc->ops->set_voltage(rdev, min_uV, max_uV, - &selector); + ret = _regulator_call_set_voltage(rdev, min_uV, max_uV, + &selector); if (ret >= 0) { if (rdev->desc->ops->list_voltage) @@ -2432,8 +2518,8 @@ static int _regulator_do_set_voltage(struct regulator_dev *rdev, if (old_selector == selector) ret = 0; else - ret = rdev->desc->ops->set_voltage_sel( - rdev, ret); + ret = _regulator_call_set_voltage_sel( + rdev, best_val, selector); } else { ret = -EINVAL; } @@ -2572,8 +2658,8 @@ EXPORT_SYMBOL_GPL(regulator_set_voltage); int regulator_set_voltage_time(struct regulator *regulator, int old_uV, int new_uV) { - struct regulator_dev *rdev = regulator->rdev; - struct regulator_ops *ops = rdev->desc->ops; + struct regulator_dev *rdev = regulator->rdev; + const struct regulator_ops *ops = rdev->desc->ops; int old_sel = -1; int new_sel = -1; int voltage; @@ -3079,11 +3165,11 @@ EXPORT_SYMBOL_GPL(regulator_unregister_notifier); /* notify regulator consumers and downstream regulator consumers. * Note mutex must be held by caller. */ -static void _notifier_call_chain(struct regulator_dev *rdev, +static int _notifier_call_chain(struct regulator_dev *rdev, unsigned long event, void *data) { /* call rdev chain first */ - blocking_notifier_call_chain(&rdev->notifier, event, data); + return blocking_notifier_call_chain(&rdev->notifier, event, data); } /** @@ -3336,9 +3422,9 @@ EXPORT_SYMBOL_GPL(regulator_mode_to_status); */ static int add_regulator_attributes(struct regulator_dev *rdev) { - struct device *dev = &rdev->dev; - struct regulator_ops *ops = rdev->desc->ops; - int status = 0; + struct device *dev = &rdev->dev; + const struct regulator_ops *ops = rdev->desc->ops; + int status = 0; /* some attributes need specific methods to be displayed */ if ((ops->get_voltage && ops->get_voltage(rdev) >= 0) || @@ -3516,12 +3602,17 @@ regulator_register(const struct regulator_desc *regulator_desc, return ERR_PTR(-EINVAL); } - init_data = config->init_data; - rdev = kzalloc(sizeof(struct regulator_dev), GFP_KERNEL); if (rdev == NULL) return ERR_PTR(-ENOMEM); + init_data = regulator_of_get_init_data(dev, regulator_desc, + &rdev->dev.of_node); + if (!init_data) { + init_data = config->init_data; + rdev->dev.of_node = of_node_get(config->of_node); + } + mutex_lock(®ulator_list_mutex); mutex_init(&rdev->mutex); @@ -3548,7 +3639,6 @@ regulator_register(const struct regulator_desc *regulator_desc, /* register with sysfs */ rdev->dev.class = ®ulator_class; - rdev->dev.of_node = of_node_get(config->of_node); rdev->dev.parent = dev; dev_set_name(&rdev->dev, "regulator.%d", atomic_inc_return(®ulator_no) - 1); @@ -3905,7 +3995,7 @@ core_initcall(regulator_init); static int __init regulator_init_complete(void) { struct regulator_dev *rdev; - struct regulator_ops *ops; + const struct regulator_ops *ops; struct regulation_constraints *c; int enabled, ret; diff --git a/drivers/regulator/da9211-regulator.c b/drivers/regulator/da9211-regulator.c index 1482ada..c78d210 100644 --- a/drivers/regulator/da9211-regulator.c +++ b/drivers/regulator/da9211-regulator.c @@ -1,5 +1,5 @@ /* - * da9211-regulator.c - Regulator device driver for DA9211 + * da9211-regulator.c - Regulator device driver for DA9211/DA9213 * Copyright (C) 2014 Dialog Semiconductor Ltd. * * This library is free software; you can redistribute it and/or @@ -24,9 +24,14 @@ #include <linux/regmap.h> #include <linux/irq.h> #include <linux/interrupt.h> +#include <linux/regulator/of_regulator.h> #include <linux/regulator/da9211.h> #include "da9211-regulator.h" +/* DEVICE IDs */ +#define DA9211_DEVICE_ID 0x22 +#define DA9213_DEVICE_ID 0x23 + #define DA9211_BUCK_MODE_SLEEP 1 #define DA9211_BUCK_MODE_SYNC 2 #define DA9211_BUCK_MODE_AUTO 3 @@ -42,6 +47,7 @@ struct da9211 { struct regulator_dev *rdev[DA9211_MAX_REGULATORS]; int num_regulator; int chip_irq; + int chip_id; }; static const struct regmap_range_cfg da9211_regmap_range[] = { @@ -52,14 +58,14 @@ static const struct regmap_range_cfg da9211_regmap_range[] = { .window_start = 0, .window_len = 256, .range_min = 0, - .range_max = 2*256, + .range_max = 5*128, }, }; static const struct regmap_config da9211_regmap_config = { .reg_bits = 8, .val_bits = 8, - .max_register = 2 * 256, + .max_register = 5 * 128, .ranges = da9211_regmap_range, .num_ranges = ARRAY_SIZE(da9211_regmap_range), }; @@ -69,11 +75,20 @@ static const struct regmap_config da9211_regmap_config = { #define DA9211_MAX_MV 1570 #define DA9211_STEP_MV 10 -/* Current limits for buck (uA) indices corresponds with register values */ +/* Current limits for DA9211 buck (uA) indices + * corresponds with register values + */ static const int da9211_current_limits[] = { 2000000, 2200000, 2400000, 2600000, 2800000, 3000000, 3200000, 3400000, 3600000, 3800000, 4000000, 4200000, 4400000, 4600000, 4800000, 5000000 }; +/* Current limits for DA9213 buck (uA) indices + * corresponds with register values + */ +static const int da9213_current_limits[] = { + 3000000, 3200000, 3400000, 3600000, 3800000, 4000000, 4200000, 4400000, + 4600000, 4800000, 5000000, 5200000, 5400000, 5600000, 5800000, 6000000 +}; static unsigned int da9211_buck_get_mode(struct regulator_dev *rdev) { @@ -129,12 +144,26 @@ static int da9211_set_current_limit(struct regulator_dev *rdev, int min, { int id = rdev_get_id(rdev); struct da9211 *chip = rdev_get_drvdata(rdev); - int i; + int i, max_size; + const int *current_limits; + + switch (chip->chip_id) { + case DA9211: + current_limits = da9211_current_limits; + max_size = ARRAY_SIZE(da9211_current_limits)-1; + break; + case DA9213: + current_limits = da9213_current_limits; + max_size = ARRAY_SIZE(da9213_current_limits)-1; + break; + default: + return -EINVAL; + } /* search for closest to maximum */ - for (i = ARRAY_SIZE(da9211_current_limits)-1; i >= 0; i--) { - if (min <= da9211_current_limits[i] && - max >= da9211_current_limits[i]) { + for (i = max_size; i >= 0; i--) { + if (min <= current_limits[i] && + max >= current_limits[i]) { return regmap_update_bits(chip->regmap, DA9211_REG_BUCK_ILIM, (0x0F << id*4), (i << id*4)); @@ -150,14 +179,28 @@ static int da9211_get_current_limit(struct regulator_dev *rdev) struct da9211 *chip = rdev_get_drvdata(rdev); unsigned int data; int ret; + const int *current_limits; + + switch (chip->chip_id) { + case DA9211: + current_limits = da9211_current_limits; + break; + case DA9213: + current_limits = da9213_current_limits; + break; + default: + return -EINVAL; + } ret = regmap_read(chip->regmap, DA9211_REG_BUCK_ILIM, &data); if (ret < 0) return ret; - /* select one of 16 values: 0000 (2000mA) to 1111 (5000mA) */ + /* select one of 16 values: 0000 (2000mA or 3000mA) + * to 1111 (5000mA or 6000mA). + */ data = (data >> id*4) & 0x0F; - return da9211_current_limits[data]; + return current_limits[data]; } static struct regulator_ops da9211_buck_ops = { @@ -194,6 +237,59 @@ static struct regulator_desc da9211_regulators[] = { DA9211_BUCK(BUCKB), }; +#ifdef CONFIG_OF +static struct of_regulator_match da9211_matches[] = { + [DA9211_ID_BUCKA] = { .name = "BUCKA" }, + [DA9211_ID_BUCKB] = { .name = "BUCKB" }, + }; + +static struct da9211_pdata *da9211_parse_regulators_dt( + struct device *dev) +{ + struct da9211_pdata *pdata; + struct device_node *node; + int i, num, n; + + node = of_get_child_by_name(dev->of_node, "regulators"); + if (!node) { + dev_err(dev, "regulators node not found\n"); + return ERR_PTR(-ENODEV); + } + + num = of_regulator_match(dev, node, da9211_matches, + ARRAY_SIZE(da9211_matches)); + of_node_put(node); + if (num < 0) { + dev_err(dev, "Failed to match regulators\n"); + return ERR_PTR(-EINVAL); + } + + pdata = devm_kzalloc(dev, sizeof(*pdata), GFP_KERNEL); + if (!pdata) + return ERR_PTR(-ENOMEM); + + pdata->num_buck = num; + + n = 0; + for (i = 0; i < ARRAY_SIZE(da9211_matches); i++) { + if (!da9211_matches[i].init_data) + continue; + + pdata->init_data[n] = da9211_matches[i].init_data; + + n++; + } + + return pdata; +} +#else +static struct da9211_pdata *da9211_parse_regulators_dt( + struct device *dev) +{ + return ERR_PTR(-ENODEV); +} +#endif + static irqreturn_t da9211_irq_handler(int irq, void *data) { struct da9211 *chip = data; @@ -264,13 +360,11 @@ static int da9211_regulator_init(struct da9211 *chip) } for (i = 0; i < chip->num_regulator; i++) { - if (chip->pdata) - config.init_data = - &(chip->pdata->init_data[i]); - + config.init_data = chip->pdata->init_data[i]; config.dev = chip->dev; config.driver_data = chip; config.regmap = chip->regmap; + config.of_node = chip->dev->of_node; chip->rdev[i] = devm_regulator_register(chip->dev, &da9211_regulators[i], &config); @@ -282,7 +376,7 @@ static int da9211_regulator_init(struct da9211 *chip) if (chip->chip_irq != 0) { ret = regmap_update_bits(chip->regmap, - DA9211_REG_MASK_B, DA9211_M_OV_CURR_A << i, 1); + DA9211_REG_MASK_B, DA9211_M_OV_CURR_A << i, 0); if (ret < 0) { dev_err(chip->dev, "Failed to update mask reg: %d\n", ret); @@ -293,6 +387,7 @@ static int da9211_regulator_init(struct da9211 *chip) return 0; } + /* * I2C driver interface functions */ @@ -301,14 +396,17 @@ static int da9211_i2c_probe(struct i2c_client *i2c, { struct da9211 *chip; int error, ret; + unsigned int data; chip = devm_kzalloc(&i2c->dev, sizeof(struct da9211), GFP_KERNEL); + if (!chip) + return -ENOMEM; chip->dev = &i2c->dev; chip->regmap = devm_regmap_init_i2c(i2c, &da9211_regmap_config); if (IS_ERR(chip->regmap)) { error = PTR_ERR(chip->regmap); - dev_err(&i2c->dev, "Failed to allocate register map: %d\n", + dev_err(chip->dev, "Failed to allocate register map: %d\n", error); return error; } @@ -316,11 +414,33 @@ static int da9211_i2c_probe(struct i2c_client *i2c, i2c_set_clientdata(i2c, chip); chip->pdata = i2c->dev.platform_data; - if (!chip->pdata) { - dev_err(&i2c->dev, "No platform init data supplied\n"); + + ret = regmap_read(chip->regmap, DA9211_REG_DEVICE_ID, &data); + if (ret < 0) { + dev_err(chip->dev, "Failed to read DEVICE_ID reg: %d\n", ret); + return ret; + } + + switch (data) { + case DA9211_DEVICE_ID: + chip->chip_id = DA9211; + break; + case DA9213_DEVICE_ID: + chip->chip_id = DA9213; + break; + default: + dev_err(chip->dev, "Unsupported device id = 0x%x.\n", data); return -ENODEV; } + if (!chip->pdata) + chip->pdata = da9211_parse_regulators_dt(chip->dev); + + if (IS_ERR(chip->pdata)) { + dev_err(chip->dev, "No regulators defined for the platform\n"); + return PTR_ERR(chip->pdata); + } + chip->chip_irq = i2c->irq; if (chip->chip_irq != 0) { @@ -340,22 +460,32 @@ static int da9211_i2c_probe(struct i2c_client *i2c, ret = da9211_regulator_init(chip); if (ret < 0) - dev_err(&i2c->dev, "Failed to initialize regulator: %d\n", ret); + dev_err(chip->dev, "Failed to initialize regulator: %d\n", ret); return ret; } static const struct i2c_device_id da9211_i2c_id[] = { - {"da9211", 0}, + {"da9211", DA9211}, + {"da9213", DA9213}, {}, }; - MODULE_DEVICE_TABLE(i2c, da9211_i2c_id); +#ifdef CONFIG_OF +static const struct of_device_id da9211_dt_ids[] = { + { .compatible = "dlg,da9211", .data = &da9211_i2c_id[0] }, + { .compatible = "dlg,da9213", .data = &da9211_i2c_id[1] }, + {}, +}; +MODULE_DEVICE_TABLE(of, da9211_dt_ids); +#endif + static struct i2c_driver da9211_regulator_driver = { .driver = { .name = "da9211", .owner = THIS_MODULE, + .of_match_table = of_match_ptr(da9211_dt_ids), }, .probe = da9211_i2c_probe, .id_table = da9211_i2c_id, @@ -364,5 +494,5 @@ static struct i2c_driver da9211_regulator_driver = { module_i2c_driver(da9211_regulator_driver); MODULE_AUTHOR("James Ban <James.Ban.opensource@diasemi.com>"); -MODULE_DESCRIPTION("Regulator device driver for Dialog DA9211"); +MODULE_DESCRIPTION("Regulator device driver for Dialog DA9211/DA9213"); MODULE_LICENSE("GPL v2"); diff --git a/drivers/regulator/da9211-regulator.h b/drivers/regulator/da9211-regulator.h index 88b1769..93fa9df 100644 --- a/drivers/regulator/da9211-regulator.h +++ b/drivers/regulator/da9211-regulator.h @@ -1,5 +1,5 @@ /* - * da9211-regulator.h - Regulator definitions for DA9211 + * da9211-regulator.h - Regulator definitions for DA9211/DA9213 * Copyright (C) 2014 Dialog Semiconductor Ltd. * * This library is free software; you can redistribute it and/or @@ -53,12 +53,15 @@ /* BUCK Phase Selection*/ #define DA9211_REG_CONFIG_E 0x147 +/* Device ID */ +#define DA9211_REG_DEVICE_ID 0x201 + /* * Registers bits */ /* DA9211_REG_PAGE_CON (addr=0x00) */ #define DA9211_REG_PAGE_SHIFT 1 -#define DA9211_REG_PAGE_MASK 0x02 +#define DA9211_REG_PAGE_MASK 0x06 /* On I2C registers 0x00 - 0xFF */ #define DA9211_REG_PAGE0 0 /* On I2C registers 0x100 - 0x1FF */ diff --git a/drivers/regulator/fan53555.c b/drivers/regulator/fan53555.c index 714fd9a..f8e4257 100644 --- a/drivers/regulator/fan53555.c +++ b/drivers/regulator/fan53555.c @@ -18,6 +18,8 @@ #include <linux/platform_device.h> #include <linux/regulator/driver.h> #include <linux/regulator/machine.h> +#include <linux/regulator/of_regulator.h> +#include <linux/of_device.h> #include <linux/i2c.h> #include <linux/slab.h> #include <linux/regmap.h> @@ -50,6 +52,11 @@ #define FAN53555_NVOLTAGES 64 /* Numbers of voltages */ +enum fan53555_vendor { + FAN53555_VENDOR_FAIRCHILD = 0, + FAN53555_VENDOR_SILERGY, +}; + /* IC Type */ enum { FAN53555_CHIP_ID_00 = 0, @@ -60,7 +67,12 @@ enum { FAN53555_CHIP_ID_05, }; +enum { + SILERGY_SYR82X = 8, +}; + struct fan53555_device_info { + enum fan53555_vendor vendor; struct regmap *regmap; struct device *dev; struct regulator_desc desc; @@ -135,6 +147,38 @@ static unsigned int fan53555_get_mode(struct regulator_dev *rdev) return REGULATOR_MODE_NORMAL; } +static int slew_rates[] = { + 64000, + 32000, + 16000, + 8000, + 4000, + 2000, + 1000, + 500, +}; + +static int fan53555_set_ramp(struct regulator_dev *rdev, int ramp) +{ + struct fan53555_device_info *di = rdev_get_drvdata(rdev); + int regval = -1, i; + + for (i = 0; i < ARRAY_SIZE(slew_rates); i++) { + if (ramp <= slew_rates[i]) + regval = i; + else + break; + } + + if (regval < 0) { + dev_err(di->dev, "unsupported ramp value %d\n", ramp); + return -EINVAL; + } + + return regmap_update_bits(di->regmap, FAN53555_CONTROL, + CTL_SLEW_MASK, regval << CTL_SLEW_SHIFT); +} + static struct regulator_ops fan53555_regulator_ops = { .set_voltage_sel = regulator_set_voltage_sel_regmap, .get_voltage_sel = regulator_get_voltage_sel_regmap, @@ -146,8 +190,50 @@ static struct regulator_ops fan53555_regulator_ops = { .is_enabled = regulator_is_enabled_regmap, .set_mode = fan53555_set_mode, .get_mode = fan53555_get_mode, + .set_ramp_delay = fan53555_set_ramp, }; +static int fan53555_voltages_setup_fairchild(struct fan53555_device_info *di) +{ + /* Init voltage range and step */ + switch (di->chip_id) { + case FAN53555_CHIP_ID_00: + case FAN53555_CHIP_ID_01: + case FAN53555_CHIP_ID_03: + case FAN53555_CHIP_ID_05: + di->vsel_min = 600000; + di->vsel_step = 10000; + break; + case FAN53555_CHIP_ID_04: + di->vsel_min = 603000; + di->vsel_step = 12826; + break; + default: + dev_err(di->dev, + "Chip ID %d not supported!\n", di->chip_id); + return -EINVAL; + } + + return 0; +} + +static int fan53555_voltages_setup_silergy(struct fan53555_device_info *di) +{ + /* Init voltage range and step */ + switch (di->chip_id) { + case SILERGY_SYR82X: + di->vsel_min = 712500; + di->vsel_step = 12500; + break; + default: + dev_err(di->dev, + "Chip ID %d not supported!\n", di->chip_id); + return -EINVAL; + } + + return 0; +} + /* For 00,01,03,05 options: * VOUT = 0.60V + NSELx * 10mV, from 0.60 to 1.23V. * For 04 option: @@ -156,7 +242,7 @@ static struct regulator_ops fan53555_regulator_ops = { static int fan53555_device_setup(struct fan53555_device_info *di, struct fan53555_platform_data *pdata) { - unsigned int reg, data, mask; + int ret = 0; /* Setup voltage control register */ switch (pdata->sleep_vsel_id) { @@ -172,33 +258,20 @@ static int fan53555_device_setup(struct fan53555_device_info *di, dev_err(di->dev, "Invalid VSEL ID!\n"); return -EINVAL; } - /* Init voltage range and step */ - switch (di->chip_id) { - case FAN53555_CHIP_ID_00: - case FAN53555_CHIP_ID_01: - case FAN53555_CHIP_ID_03: - case FAN53555_CHIP_ID_05: - di->vsel_min = 600000; - di->vsel_step = 10000; + + switch (di->vendor) { + case FAN53555_VENDOR_FAIRCHILD: + ret = fan53555_voltages_setup_fairchild(di); break; - case FAN53555_CHIP_ID_04: - di->vsel_min = 603000; - di->vsel_step = 12826; + case FAN53555_VENDOR_SILERGY: + ret = fan53555_voltages_setup_silergy(di); break; default: - dev_err(di->dev, - "Chip ID[%d]\n not supported!\n", di->chip_id); + dev_err(di->dev, "vendor %d not supported!\n", di->vendor); return -EINVAL; } - /* Init slew rate */ - if (pdata->slew_rate & 0x7) - di->slew_rate = pdata->slew_rate; - else - di->slew_rate = FAN53555_SLEW_RATE_64MV; - reg = FAN53555_CONTROL; - data = di->slew_rate << CTL_SLEW_SHIFT; - mask = CTL_SLEW_MASK; - return regmap_update_bits(di->regmap, reg, mask, data); + + return ret; } static int fan53555_regulator_register(struct fan53555_device_info *di, @@ -207,6 +280,7 @@ static int fan53555_regulator_register(struct fan53555_device_info *di, struct regulator_desc *rdesc = &di->desc; rdesc->name = "fan53555-reg"; + rdesc->supply_name = "vin"; rdesc->ops = &fan53555_regulator_ops; rdesc->type = REGULATOR_VOLTAGE; rdesc->n_voltages = FAN53555_NVOLTAGES; @@ -227,9 +301,46 @@ static struct regmap_config fan53555_regmap_config = { .val_bits = 8, }; +static struct fan53555_platform_data *fan53555_parse_dt(struct device *dev, + struct device_node *np) +{ + struct fan53555_platform_data *pdata; + int ret; + u32 tmp; + + pdata = devm_kzalloc(dev, sizeof(*pdata), GFP_KERNEL); + if (!pdata) + return NULL; + + pdata->regulator = of_get_regulator_init_data(dev, np); + + ret = of_property_read_u32(np, "fcs,suspend-voltage-selector", + &tmp); + if (!ret) + pdata->sleep_vsel_id = tmp; + + return pdata; +} + +static const struct of_device_id fan53555_dt_ids[] = { + { + .compatible = "fcs,fan53555", + .data = (void *)FAN53555_VENDOR_FAIRCHILD + }, { + .compatible = "silergy,syr827", + .data = (void *)FAN53555_VENDOR_SILERGY, + }, { + .compatible = "silergy,syr828", + .data = (void *)FAN53555_VENDOR_SILERGY, + }, + { } +}; +MODULE_DEVICE_TABLE(of, fan53555_dt_ids); + static int fan53555_regulator_probe(struct i2c_client *client, const struct i2c_device_id *id) { + struct device_node *np = client->dev.of_node; struct fan53555_device_info *di; struct fan53555_platform_data *pdata; struct regulator_config config = { }; @@ -237,6 +348,9 @@ static int fan53555_regulator_probe(struct i2c_client *client, int ret; pdata = dev_get_platdata(&client->dev); + if (!pdata) + pdata = fan53555_parse_dt(&client->dev, np); + if (!pdata || !pdata->regulator) { dev_err(&client->dev, "Platform data not found!\n"); return -ENODEV; @@ -247,13 +361,35 @@ static int fan53555_regulator_probe(struct i2c_client *client, if (!di) return -ENOMEM; + di->regulator = pdata->regulator; + if (client->dev.of_node) { + const struct of_device_id *match; + + match = of_match_device(of_match_ptr(fan53555_dt_ids), + &client->dev); + if (!match) + return -ENODEV; + + di->vendor = (unsigned long) match->data; + } else { + /* if no ramp constraint set, get the pdata ramp_delay */ + if (!di->regulator->constraints.ramp_delay) { + int slew_idx = (pdata->slew_rate & 0x7) + ? pdata->slew_rate : 0; + + di->regulator->constraints.ramp_delay + = slew_rates[slew_idx]; + } + + di->vendor = id->driver_data; + } + di->regmap = devm_regmap_init_i2c(client, &fan53555_regmap_config); if (IS_ERR(di->regmap)) { dev_err(&client->dev, "Failed to allocate regmap!\n"); return PTR_ERR(di->regmap); } di->dev = &client->dev; - di->regulator = pdata->regulator; i2c_set_clientdata(client, di); /* Get chip ID */ ret = regmap_read(di->regmap, FAN53555_ID1, &val); @@ -282,6 +418,8 @@ static int fan53555_regulator_probe(struct i2c_client *client, config.init_data = di->regulator; config.regmap = di->regmap; config.driver_data = di; + config.of_node = np; + ret = fan53555_regulator_register(di, &config); if (ret < 0) dev_err(&client->dev, "Failed to register regulator!\n"); @@ -290,13 +428,20 @@ static int fan53555_regulator_probe(struct i2c_client *client, } static const struct i2c_device_id fan53555_id[] = { - {"fan53555", -1}, + { + .name = "fan53555", + .driver_data = FAN53555_VENDOR_FAIRCHILD + }, { + .name = "syr82x", + .driver_data = FAN53555_VENDOR_SILERGY + }, { }, }; static struct i2c_driver fan53555_regulator_driver = { .driver = { .name = "fan53555-regulator", + .of_match_table = of_match_ptr(fan53555_dt_ids), }, .probe = fan53555_regulator_probe, .id_table = fan53555_id, diff --git a/drivers/regulator/hi6421-regulator.c b/drivers/regulator/hi6421-regulator.c new file mode 100644 index 0000000..156d0d1 --- /dev/null +++ b/drivers/regulator/hi6421-regulator.c @@ -0,0 +1,634 @@ +/* + * Device driver for regulators in Hi6421 IC + * + * Copyright (c) <2011-2014> HiSilicon Technologies Co., Ltd. + * http://www.hisilicon.com + * Copyright (c) <2013-2014> Linaro Ltd. + * http://www.linaro.org + * + * Author: Guodong Xu <guodong.xu@linaro.org> + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + */ + +#include <linux/slab.h> +#include <linux/device.h> +#include <linux/module.h> +#include <linux/err.h> +#include <linux/platform_device.h> +#include <linux/of.h> +#include <linux/regmap.h> +#include <linux/regulator/driver.h> +#include <linux/regulator/machine.h> +#include <linux/regulator/of_regulator.h> +#include <linux/mfd/hi6421-pmic.h> + +/* + * struct hi6421_regulator_pdata - Hi6421 regulator data of platform device + * @lock: mutex to serialize regulator enable + */ +struct hi6421_regulator_pdata { + struct mutex lock; +}; + +/* + * struct hi6421_regulator_info - hi6421 regulator information + * @desc: regulator description + * @mode_mask: ECO mode bitmask of LDOs; for BUCKs, this masks sleep + * @eco_microamp: eco mode load upper limit (in uA), valid for LDOs only + */ +struct hi6421_regulator_info { + struct regulator_desc desc; + u8 mode_mask; + u32 eco_microamp; +}; + +/* HI6421 regulators */ +enum hi6421_regulator_id { + HI6421_LDO0, + HI6421_LDO1, + HI6421_LDO2, + HI6421_LDO3, + HI6421_LDO4, + HI6421_LDO5, + HI6421_LDO6, + HI6421_LDO7, + HI6421_LDO8, + HI6421_LDO9, + HI6421_LDO10, + HI6421_LDO11, + HI6421_LDO12, + HI6421_LDO13, + HI6421_LDO14, + HI6421_LDO15, + HI6421_LDO16, + HI6421_LDO17, + HI6421_LDO18, + HI6421_LDO19, + HI6421_LDO20, + HI6421_LDOAUDIO, + HI6421_BUCK0, + HI6421_BUCK1, + HI6421_BUCK2, + HI6421_BUCK3, + HI6421_BUCK4, + HI6421_BUCK5, + HI6421_NUM_REGULATORS, +}; + +#define HI6421_REGULATOR_OF_MATCH(_name, id) \ +{ \ + .name = #_name, \ + .driver_data = (void *) HI6421_##id, \ +} + +static struct of_regulator_match hi6421_regulator_match[] = { + HI6421_REGULATOR_OF_MATCH(hi6421_vout0, LDO0), + HI6421_REGULATOR_OF_MATCH(hi6421_vout1, LDO1), + HI6421_REGULATOR_OF_MATCH(hi6421_vout2, LDO2), + HI6421_REGULATOR_OF_MATCH(hi6421_vout3, LDO3), + HI6421_REGULATOR_OF_MATCH(hi6421_vout4, LDO4), + HI6421_REGULATOR_OF_MATCH(hi6421_vout5, LDO5), + HI6421_REGULATOR_OF_MATCH(hi6421_vout6, LDO6), + HI6421_REGULATOR_OF_MATCH(hi6421_vout7, LDO7), + HI6421_REGULATOR_OF_MATCH(hi6421_vout8, LDO8), + HI6421_REGULATOR_OF_MATCH(hi6421_vout9, LDO9), + HI6421_REGULATOR_OF_MATCH(hi6421_vout10, LDO10), + HI6421_REGULATOR_OF_MATCH(hi6421_vout11, LDO11), + HI6421_REGULATOR_OF_MATCH(hi6421_vout12, LDO12), + HI6421_REGULATOR_OF_MATCH(hi6421_vout13, LDO13), + HI6421_REGULATOR_OF_MATCH(hi6421_vout14, LDO14), + HI6421_REGULATOR_OF_MATCH(hi6421_vout15, LDO15), + HI6421_REGULATOR_OF_MATCH(hi6421_vout16, LDO16), + HI6421_REGULATOR_OF_MATCH(hi6421_vout17, LDO17), + HI6421_REGULATOR_OF_MATCH(hi6421_vout18, LDO18), + HI6421_REGULATOR_OF_MATCH(hi6421_vout19, LDO19), + HI6421_REGULATOR_OF_MATCH(hi6421_vout20, LDO20), + HI6421_REGULATOR_OF_MATCH(hi6421_vout_audio, LDOAUDIO), + HI6421_REGULATOR_OF_MATCH(hi6421_buck0, BUCK0), + HI6421_REGULATOR_OF_MATCH(hi6421_buck1, BUCK1), + HI6421_REGULATOR_OF_MATCH(hi6421_buck2, BUCK2), + HI6421_REGULATOR_OF_MATCH(hi6421_buck3, BUCK3), + HI6421_REGULATOR_OF_MATCH(hi6421_buck4, BUCK4), + HI6421_REGULATOR_OF_MATCH(hi6421_buck5, BUCK5), +}; + +/* LDO 0, 4~7, 9~14, 16~20 have same voltage table. */ +static const unsigned int ldo_0_voltages[] = { + 1500000, 1800000, 2400000, 2500000, + 2600000, 2700000, 2850000, 3000000, +}; + +/* LDO 8, 15 have same voltage table. */ +static const unsigned int ldo_8_voltages[] = { + 1500000, 1800000, 2400000, 2600000, + 2700000, 2850000, 3000000, 3300000, +}; + +/* Ranges are sorted in ascending order. */ +static const struct regulator_linear_range ldo_audio_volt_range[] = { + REGULATOR_LINEAR_RANGE(2800000, 0, 3, 50000), + REGULATOR_LINEAR_RANGE(3000000, 4, 7, 100000), +}; + +static const unsigned int buck_3_voltages[] = { + 950000, 1050000, 1100000, 1117000, + 1134000, 1150000, 1167000, 1200000, +}; + +static const unsigned int buck_4_voltages[] = { + 1150000, 1200000, 1250000, 1350000, + 1700000, 1800000, 1900000, 2000000, +}; + +static const unsigned int buck_5_voltages[] = { + 1150000, 1200000, 1250000, 1350000, + 1600000, 1700000, 1800000, 1900000, +}; + +static const struct regulator_ops hi6421_ldo_ops; +static const struct regulator_ops hi6421_ldo_linear_ops; +static const struct regulator_ops hi6421_ldo_linear_range_ops; +static const struct regulator_ops hi6421_buck012_ops; +static const struct regulator_ops hi6421_buck345_ops; + +#define HI6421_LDO_ENABLE_TIME (350) +/* + * _id - LDO id name string + * v_table - voltage table + * vreg - voltage select register + * vmask - voltage select mask + * ereg - enable register + * emask - enable mask + * odelay - off/on delay time in uS + * ecomask - eco mode mask + * ecoamp - eco mode load uppler limit in uA + */ +#define HI6421_LDO(_id, v_table, vreg, vmask, ereg, emask, \ + odelay, ecomask, ecoamp) \ + [HI6421_##_id] = { \ + .desc = { \ + .name = #_id, \ + .ops = &hi6421_ldo_ops, \ + .type = REGULATOR_VOLTAGE, \ + .id = HI6421_##_id, \ + .owner = THIS_MODULE, \ + .n_voltages = ARRAY_SIZE(v_table), \ + .volt_table = v_table, \ + .vsel_reg = HI6421_REG_TO_BUS_ADDR(vreg), \ + .vsel_mask = vmask, \ + .enable_reg = HI6421_REG_TO_BUS_ADDR(ereg), \ + .enable_mask = emask, \ + .enable_time = HI6421_LDO_ENABLE_TIME, \ + .off_on_delay = odelay, \ + }, \ + .mode_mask = ecomask, \ + .eco_microamp = ecoamp, \ + } + +/* HI6421 LDO1~3 are linear voltage regulators at fixed uV_step + * + * _id - LDO id name string + * _min_uV - minimum voltage supported in uV + * n_volt - number of votages available + * vstep - voltage increase in each linear step in uV + * vreg - voltage select register + * vmask - voltage select mask + * ereg - enable register + * emask - enable mask + * odelay - off/on delay time in uS + * ecomask - eco mode mask + * ecoamp - eco mode load uppler limit in uA + */ +#define HI6421_LDO_LINEAR(_id, _min_uV, n_volt, vstep, vreg, vmask, \ + ereg, emask, odelay, ecomask, ecoamp) \ + [HI6421_##_id] = { \ + .desc = { \ + .name = #_id, \ + .ops = &hi6421_ldo_linear_ops, \ + .type = REGULATOR_VOLTAGE, \ + .id = HI6421_##_id, \ + .owner = THIS_MODULE, \ + .min_uV = _min_uV, \ + .n_voltages = n_volt, \ + .uV_step = vstep, \ + .vsel_reg = HI6421_REG_TO_BUS_ADDR(vreg), \ + .vsel_mask = vmask, \ + .enable_reg = HI6421_REG_TO_BUS_ADDR(ereg), \ + .enable_mask = emask, \ + .enable_time = HI6421_LDO_ENABLE_TIME, \ + .off_on_delay = odelay, \ + }, \ + .mode_mask = ecomask, \ + .eco_microamp = ecoamp, \ + } + +/* HI6421 LDOAUDIO is a linear voltage regulator with two 4-step ranges + * + * _id - LDO id name string + * n_volt - number of votages available + * volt_ranges - array of regulator_linear_range + * vstep - voltage increase in each linear step in uV + * vreg - voltage select register + * vmask - voltage select mask + * ereg - enable register + * emask - enable mask + * odelay - off/on delay time in uS + * ecomask - eco mode mask + * ecoamp - eco mode load uppler limit in uA + */ +#define HI6421_LDO_LINEAR_RANGE(_id, n_volt, volt_ranges, vreg, vmask, \ + ereg, emask, odelay, ecomask, ecoamp) \ + [HI6421_##_id] = { \ + .desc = { \ + .name = #_id, \ + .ops = &hi6421_ldo_linear_range_ops, \ + .type = REGULATOR_VOLTAGE, \ + .id = HI6421_##_id, \ + .owner = THIS_MODULE, \ + .n_voltages = n_volt, \ + .linear_ranges = volt_ranges, \ + .n_linear_ranges = ARRAY_SIZE(volt_ranges), \ + .vsel_reg = HI6421_REG_TO_BUS_ADDR(vreg), \ + .vsel_mask = vmask, \ + .enable_reg = HI6421_REG_TO_BUS_ADDR(ereg), \ + .enable_mask = emask, \ + .enable_time = HI6421_LDO_ENABLE_TIME, \ + .off_on_delay = odelay, \ + }, \ + .mode_mask = ecomask, \ + .eco_microamp = ecoamp, \ + } + +/* HI6421 BUCK0/1/2 are linear voltage regulators at fixed uV_step + * + * _id - BUCK0/1/2 id name string + * vreg - voltage select register + * vmask - voltage select mask + * ereg - enable register + * emask - enable mask + * sleepmask - mask of sleep mode + * etime - enable time + * odelay - off/on delay time in uS + */ +#define HI6421_BUCK012(_id, vreg, vmask, ereg, emask, sleepmask, \ + etime, odelay) \ + [HI6421_##_id] = { \ + .desc = { \ + .name = #_id, \ + .ops = &hi6421_buck012_ops, \ + .type = REGULATOR_VOLTAGE, \ + .id = HI6421_##_id, \ + .owner = THIS_MODULE, \ + .min_uV = 700000, \ + .n_voltages = 128, \ + .uV_step = 7086, \ + .vsel_reg = HI6421_REG_TO_BUS_ADDR(vreg), \ + .vsel_mask = vmask, \ + .enable_reg = HI6421_REG_TO_BUS_ADDR(ereg), \ + .enable_mask = emask, \ + .enable_time = etime, \ + .off_on_delay = odelay, \ + }, \ + .mode_mask = sleepmask, \ + } + +/* HI6421 BUCK3/4/5 share similar configurations as LDOs, with exception + * that it supports SLEEP mode, so has different .ops. + * + * _id - LDO id name string + * v_table - voltage table + * vreg - voltage select register + * vmask - voltage select mask + * ereg - enable register + * emask - enable mask + * odelay - off/on delay time in uS + * sleepmask - mask of sleep mode + */ +#define HI6421_BUCK345(_id, v_table, vreg, vmask, ereg, emask, \ + odelay, sleepmask) \ + [HI6421_##_id] = { \ + .desc = { \ + .name = #_id, \ + .ops = &hi6421_buck345_ops, \ + .type = REGULATOR_VOLTAGE, \ + .id = HI6421_##_id, \ + .owner = THIS_MODULE, \ + .n_voltages = ARRAY_SIZE(v_table), \ + .volt_table = v_table, \ + .vsel_reg = HI6421_REG_TO_BUS_ADDR(vreg), \ + .vsel_mask = vmask, \ + .enable_reg = HI6421_REG_TO_BUS_ADDR(ereg), \ + .enable_mask = emask, \ + .enable_time = HI6421_LDO_ENABLE_TIME, \ + .off_on_delay = odelay, \ + }, \ + .mode_mask = sleepmask, \ + } + +/* HI6421 regulator information */ +static struct hi6421_regulator_info + hi6421_regulator_info[HI6421_NUM_REGULATORS] = { + HI6421_LDO(LDO0, ldo_0_voltages, 0x20, 0x07, 0x20, 0x10, + 10000, 0x20, 8000), + HI6421_LDO_LINEAR(LDO1, 1700000, 4, 100000, 0x21, 0x03, 0x21, 0x10, + 10000, 0x20, 5000), + HI6421_LDO_LINEAR(LDO2, 1050000, 8, 50000, 0x22, 0x07, 0x22, 0x10, + 20000, 0x20, 8000), + HI6421_LDO_LINEAR(LDO3, 1050000, 8, 50000, 0x23, 0x07, 0x23, 0x10, + 20000, 0x20, 8000), + HI6421_LDO(LDO4, ldo_0_voltages, 0x24, 0x07, 0x24, 0x10, + 20000, 0x20, 8000), + HI6421_LDO(LDO5, ldo_0_voltages, 0x25, 0x07, 0x25, 0x10, + 20000, 0x20, 8000), + HI6421_LDO(LDO6, ldo_0_voltages, 0x26, 0x07, 0x26, 0x10, + 20000, 0x20, 8000), + HI6421_LDO(LDO7, ldo_0_voltages, 0x27, 0x07, 0x27, 0x10, + 20000, 0x20, 5000), + HI6421_LDO(LDO8, ldo_8_voltages, 0x28, 0x07, 0x28, 0x10, + 20000, 0x20, 8000), + HI6421_LDO(LDO9, ldo_0_voltages, 0x29, 0x07, 0x29, 0x10, + 40000, 0x20, 8000), + HI6421_LDO(LDO10, ldo_0_voltages, 0x2a, 0x07, 0x2a, 0x10, + 40000, 0x20, 8000), + HI6421_LDO(LDO11, ldo_0_voltages, 0x2b, 0x07, 0x2b, 0x10, + 40000, 0x20, 8000), + HI6421_LDO(LDO12, ldo_0_voltages, 0x2c, 0x07, 0x2c, 0x10, + 40000, 0x20, 8000), + HI6421_LDO(LDO13, ldo_0_voltages, 0x2d, 0x07, 0x2d, 0x10, + 40000, 0x20, 8000), + HI6421_LDO(LDO14, ldo_0_voltages, 0x2e, 0x07, 0x2e, 0x10, + 40000, 0x20, 8000), + HI6421_LDO(LDO15, ldo_8_voltages, 0x2f, 0x07, 0x2f, 0x10, + 40000, 0x20, 8000), + HI6421_LDO(LDO16, ldo_0_voltages, 0x30, 0x07, 0x30, 0x10, + 40000, 0x20, 8000), + HI6421_LDO(LDO17, ldo_0_voltages, 0x31, 0x07, 0x31, 0x10, + 40000, 0x20, 8000), + HI6421_LDO(LDO18, ldo_0_voltages, 0x32, 0x07, 0x32, 0x10, + 40000, 0x20, 8000), + HI6421_LDO(LDO19, ldo_0_voltages, 0x33, 0x07, 0x33, 0x10, + 40000, 0x20, 8000), + HI6421_LDO(LDO20, ldo_0_voltages, 0x34, 0x07, 0x34, 0x10, + 40000, 0x20, 8000), + HI6421_LDO_LINEAR_RANGE(LDOAUDIO, 8, ldo_audio_volt_range, 0x36, + 0x70, 0x36, 0x01, 40000, 0x02, 5000), + HI6421_BUCK012(BUCK0, 0x0d, 0x7f, 0x0c, 0x01, 0x10, 400, 20000), + HI6421_BUCK012(BUCK1, 0x0f, 0x7f, 0x0e, 0x01, 0x10, 400, 20000), + HI6421_BUCK012(BUCK2, 0x11, 0x7f, 0x10, 0x01, 0x10, 350, 100), + HI6421_BUCK345(BUCK3, buck_3_voltages, 0x13, 0x07, 0x12, 0x01, + 20000, 0x10), + HI6421_BUCK345(BUCK4, buck_4_voltages, 0x15, 0x07, 0x14, 0x01, + 20000, 0x10), + HI6421_BUCK345(BUCK5, buck_5_voltages, 0x17, 0x07, 0x16, 0x01, + 20000, 0x10), +}; + +static int hi6421_regulator_enable(struct regulator_dev *rdev) +{ + struct hi6421_regulator_pdata *pdata; + + pdata = dev_get_drvdata(rdev->dev.parent); + /* hi6421 spec requires regulator enablement must be serialized: + * - Because when BUCK, LDO switching from off to on, it will have + * a huge instantaneous current; so you can not turn on two or + * more LDO or BUCKs simultaneously, or it may burn the chip. + */ + mutex_lock(&pdata->lock); + + /* call regulator regmap helper */ + regulator_enable_regmap(rdev); + + mutex_unlock(&pdata->lock); + return 0; +} + +static unsigned int hi6421_regulator_ldo_get_mode(struct regulator_dev *rdev) +{ + struct hi6421_regulator_info *info = rdev_get_drvdata(rdev); + u32 reg_val; + + regmap_read(rdev->regmap, rdev->desc->enable_reg, ®_val); + if (reg_val & info->mode_mask) + return REGULATOR_MODE_IDLE; + + return REGULATOR_MODE_NORMAL; +} + +static unsigned int hi6421_regulator_buck_get_mode(struct regulator_dev *rdev) +{ + struct hi6421_regulator_info *info = rdev_get_drvdata(rdev); + u32 reg_val; + + regmap_read(rdev->regmap, rdev->desc->enable_reg, ®_val); + if (reg_val & info->mode_mask) + return REGULATOR_MODE_STANDBY; + + return REGULATOR_MODE_NORMAL; +} + +static int hi6421_regulator_ldo_set_mode(struct regulator_dev *rdev, + unsigned int mode) +{ + struct hi6421_regulator_info *info = rdev_get_drvdata(rdev); + u32 new_mode; + + switch (mode) { + case REGULATOR_MODE_NORMAL: + new_mode = 0; + break; + case REGULATOR_MODE_IDLE: + new_mode = info->mode_mask; + break; + default: + return -EINVAL; + } + + /* set mode */ + regmap_update_bits(rdev->regmap, rdev->desc->enable_reg, + info->mode_mask, new_mode); + + return 0; +} + +static int hi6421_regulator_buck_set_mode(struct regulator_dev *rdev, + unsigned int mode) +{ + struct hi6421_regulator_info *info = rdev_get_drvdata(rdev); + u32 new_mode; + + switch (mode) { + case REGULATOR_MODE_NORMAL: + new_mode = 0; + break; + case REGULATOR_MODE_STANDBY: + new_mode = info->mode_mask; + break; + default: + return -EINVAL; + } + + /* set mode */ + regmap_update_bits(rdev->regmap, rdev->desc->enable_reg, + info->mode_mask, new_mode); + + return 0; +} + +unsigned int hi6421_regulator_ldo_get_optimum_mode(struct regulator_dev *rdev, + int input_uV, int output_uV, int load_uA) +{ + struct hi6421_regulator_info *info = rdev_get_drvdata(rdev); + + if (load_uA > info->eco_microamp) + return REGULATOR_MODE_NORMAL; + + return REGULATOR_MODE_IDLE; +} + +static const struct regulator_ops hi6421_ldo_ops = { + .is_enabled = regulator_is_enabled_regmap, + .enable = hi6421_regulator_enable, + .disable = regulator_disable_regmap, + .list_voltage = regulator_list_voltage_table, + .map_voltage = regulator_map_voltage_ascend, + .get_voltage_sel = regulator_get_voltage_sel_regmap, + .set_voltage_sel = regulator_set_voltage_sel_regmap, + .get_mode = hi6421_regulator_ldo_get_mode, + .set_mode = hi6421_regulator_ldo_set_mode, + .get_optimum_mode = hi6421_regulator_ldo_get_optimum_mode, +}; + +static const struct regulator_ops hi6421_ldo_linear_ops = { + .is_enabled = regulator_is_enabled_regmap, + .enable = hi6421_regulator_enable, + .disable = regulator_disable_regmap, + .list_voltage = regulator_list_voltage_linear, + .map_voltage = regulator_map_voltage_linear, + .get_voltage_sel = regulator_get_voltage_sel_regmap, + .set_voltage_sel = regulator_set_voltage_sel_regmap, + .get_mode = hi6421_regulator_ldo_get_mode, + .set_mode = hi6421_regulator_ldo_set_mode, + .get_optimum_mode = hi6421_regulator_ldo_get_optimum_mode, +}; + +static const struct regulator_ops hi6421_ldo_linear_range_ops = { + .is_enabled = regulator_is_enabled_regmap, + .enable = hi6421_regulator_enable, + .disable = regulator_disable_regmap, + .list_voltage = regulator_list_voltage_linear_range, + .map_voltage = regulator_map_voltage_linear_range, + .get_voltage_sel = regulator_get_voltage_sel_regmap, + .set_voltage_sel = regulator_set_voltage_sel_regmap, + .get_mode = hi6421_regulator_ldo_get_mode, + .set_mode = hi6421_regulator_ldo_set_mode, + .get_optimum_mode = hi6421_regulator_ldo_get_optimum_mode, +}; + +static const struct regulator_ops hi6421_buck012_ops = { + .is_enabled = regulator_is_enabled_regmap, + .enable = hi6421_regulator_enable, + .disable = regulator_disable_regmap, + .list_voltage = regulator_list_voltage_linear, + .map_voltage = regulator_map_voltage_linear, + .get_voltage_sel = regulator_get_voltage_sel_regmap, + .set_voltage_sel = regulator_set_voltage_sel_regmap, + .get_mode = hi6421_regulator_buck_get_mode, + .set_mode = hi6421_regulator_buck_set_mode, +}; + +static const struct regulator_ops hi6421_buck345_ops = { + .is_enabled = regulator_is_enabled_regmap, + .enable = hi6421_regulator_enable, + .disable = regulator_disable_regmap, + .list_voltage = regulator_list_voltage_table, + .map_voltage = regulator_map_voltage_ascend, + .get_voltage_sel = regulator_get_voltage_sel_regmap, + .set_voltage_sel = regulator_set_voltage_sel_regmap, + .get_mode = hi6421_regulator_buck_get_mode, + .set_mode = hi6421_regulator_buck_set_mode, +}; + +static int hi6421_regulator_register(struct platform_device *pdev, + struct regmap *rmap, + struct regulator_init_data *init_data, + int id, struct device_node *np) +{ + struct hi6421_regulator_info *info = NULL; + struct regulator_config config = { }; + struct regulator_dev *rdev; + + /* assign per-regulator data */ + info = &hi6421_regulator_info[id]; + + config.dev = &pdev->dev; + config.init_data = init_data; + config.driver_data = info; + config.regmap = rmap; + config.of_node = np; + + /* register regulator with framework */ + rdev = devm_regulator_register(&pdev->dev, &info->desc, &config); + if (IS_ERR(rdev)) { + dev_err(&pdev->dev, "failed to register regulator %s\n", + info->desc.name); + return PTR_ERR(rdev); + } + + return 0; +} + +static int hi6421_regulator_probe(struct platform_device *pdev) +{ + struct device *dev = &pdev->dev; + struct device_node *np; + struct hi6421_pmic *pmic; + struct hi6421_regulator_pdata *pdata; + int i, ret = 0; + + pdata = devm_kzalloc(&pdev->dev, sizeof(*pdata), GFP_KERNEL); + if (!pdata) + return -ENOMEM; + mutex_init(&pdata->lock); + platform_set_drvdata(pdev, pdata); + + np = of_get_child_by_name(dev->parent->of_node, "regulators"); + if (!np) + return -ENODEV; + + ret = of_regulator_match(dev, np, + hi6421_regulator_match, + ARRAY_SIZE(hi6421_regulator_match)); + of_node_put(np); + if (ret < 0) { + dev_err(dev, "Error parsing regulator init data: %d\n", ret); + return ret; + } + + pmic = dev_get_drvdata(dev->parent); + + for (i = 0; i < ARRAY_SIZE(hi6421_regulator_info); i++) { + ret = hi6421_regulator_register(pdev, pmic->regmap, + hi6421_regulator_match[i].init_data, i, + hi6421_regulator_match[i].of_node); + if (ret) + return ret; + } + + return 0; +} + +static struct platform_driver hi6421_regulator_driver = { + .driver = { + .name = "hi6421-regulator", + .owner = THIS_MODULE, + }, + .probe = hi6421_regulator_probe, +}; +module_platform_driver(hi6421_regulator_driver); + +MODULE_AUTHOR("Guodong Xu <guodong.xu@linaro.org>"); +MODULE_DESCRIPTION("Hi6421 regulator driver"); +MODULE_LICENSE("GPL v2"); diff --git a/drivers/regulator/internal.h b/drivers/regulator/internal.h index 84bbda1..80ba2a3 100644 --- a/drivers/regulator/internal.h +++ b/drivers/regulator/internal.h @@ -35,4 +35,18 @@ struct regulator { struct dentry *debugfs; }; +#ifdef CONFIG_OF +struct regulator_init_data *regulator_of_get_init_data(struct device *dev, + const struct regulator_desc *desc, + struct device_node **node); +#else +static inline struct regulator_init_data * +regulator_of_get_init_data(struct device *dev, + const struct regulator_desc *desc, + struct device_node **node) +{ + return NULL; +} +#endif + #endif diff --git a/drivers/regulator/isl9305.c b/drivers/regulator/isl9305.c new file mode 100644 index 0000000..92fefd9 --- /dev/null +++ b/drivers/regulator/isl9305.c @@ -0,0 +1,207 @@ +/* + * isl9305 - Intersil ISL9305 DCDC regulator + * + * Copyright 2014 Linaro Ltd + * + * Author: Mark Brown <broonie@kernel.org> + * + * This program is free software; you can redistribute it and/or modify it + * under the terms of the GNU General Public License as published by the + * Free Software Foundation; either version 2 of the License, or (at your + * option) any later version. + */ + +#include <linux/module.h> +#include <linux/err.h> +#include <linux/i2c.h> +#include <linux/of.h> +#include <linux/platform_data/isl9305.h> +#include <linux/regmap.h> +#include <linux/regulator/driver.h> +#include <linux/regulator/of_regulator.h> +#include <linux/slab.h> + +/* + * Registers + */ +#define ISL9305_DCD1OUT 0x0 +#define ISL9305_DCD2OUT 0x1 +#define ISL9305_LDO1OUT 0x2 +#define ISL9305_LDO2OUT 0x3 +#define ISL9305_DCD_PARAMETER 0x4 +#define ISL9305_SYSTEM_PARAMETER 0x5 +#define ISL9305_DCD_SRCTL 0x6 + +#define ISL9305_MAX_REG ISL9305_DCD_SRCTL + +/* + * DCD_PARAMETER + */ +#define ISL9305_DCD_PHASE 0x40 +#define ISL9305_DCD2_ULTRA 0x20 +#define ISL9305_DCD1_ULTRA 0x10 +#define ISL9305_DCD2_BLD 0x08 +#define ISL9305_DCD1_BLD 0x04 +#define ISL9305_DCD2_MODE 0x02 +#define ISL9305_DCD1_MODE 0x01 + +/* + * SYSTEM_PARAMETER + */ +#define ISL9305_I2C_EN 0x40 +#define ISL9305_DCDPOR_MASK 0x30 +#define ISL9305_LDO2_EN 0x08 +#define ISL9305_LDO1_EN 0x04 +#define ISL9305_DCD2_EN 0x02 +#define ISL9305_DCD1_EN 0x01 + +/* + * DCD_SRCTL + */ +#define ISL9305_DCD2SR_MASK 0xc0 +#define ISL9305_DCD1SR_MASK 0x07 + +static const struct regulator_ops isl9305_ops = { + .enable = regulator_enable_regmap, + .disable = regulator_disable_regmap, + .is_enabled = regulator_is_enabled_regmap, + .list_voltage = regulator_list_voltage_linear, + .get_voltage_sel = regulator_get_voltage_sel_regmap, + .set_voltage_sel = regulator_set_voltage_sel_regmap, +}; + +static const struct regulator_desc isl9305_regulators[] = { + [ISL9305_DCD1] = { + .name = "DCD1", + .of_match = of_match_ptr("dcd1"), + .regulators_node = of_match_ptr("regulators"), + .n_voltages = 0x70, + .min_uV = 825000, + .uV_step = 25000, + .vsel_reg = ISL9305_DCD1OUT, + .vsel_mask = 0x7f, + .enable_reg = ISL9305_SYSTEM_PARAMETER, + .enable_mask = ISL9305_DCD1_EN, + .supply_name = "VINDCD1", + .ops = &isl9305_ops, + }, + [ISL9305_DCD2] = { + .name = "DCD2", + .of_match = of_match_ptr("dcd2"), + .regulators_node = of_match_ptr("regulators"), + .n_voltages = 0x70, + .min_uV = 825000, + .uV_step = 25000, + .vsel_reg = ISL9305_DCD2OUT, + .vsel_mask = 0x7f, + .enable_reg = ISL9305_SYSTEM_PARAMETER, + .enable_mask = ISL9305_DCD2_EN, + .supply_name = "VINDCD2", + .ops = &isl9305_ops, + }, + [ISL9305_LDO1] = { + .name = "LDO1", + .of_match = of_match_ptr("ldo1"), + .regulators_node = of_match_ptr("regulators"), + .n_voltages = 0x37, + .min_uV = 900000, + .uV_step = 50000, + .vsel_reg = ISL9305_LDO1OUT, + .vsel_mask = 0x3f, + .enable_reg = ISL9305_SYSTEM_PARAMETER, + .enable_mask = ISL9305_LDO1_EN, + .supply_name = "VINLDO1", + .ops = &isl9305_ops, + }, + [ISL9305_LDO2] = { + .name = "LDO2", + .of_match = of_match_ptr("ldo2"), + .regulators_node = of_match_ptr("regulators"), + .n_voltages = 0x37, + .min_uV = 900000, + .uV_step = 50000, + .vsel_reg = ISL9305_LDO2OUT, + .vsel_mask = 0x3f, + .enable_reg = ISL9305_SYSTEM_PARAMETER, + .enable_mask = ISL9305_LDO2_EN, + .supply_name = "VINLDO2", + .ops = &isl9305_ops, + }, +}; + +static const struct regmap_config isl9305_regmap = { + .reg_bits = 8, + .val_bits = 8, + + .max_register = ISL9305_MAX_REG, + .cache_type = REGCACHE_RBTREE, +}; + +static int isl9305_i2c_probe(struct i2c_client *i2c, + const struct i2c_device_id *id) +{ + struct regulator_config config = { }; + struct isl9305_pdata *pdata = i2c->dev.platform_data; + struct regulator_dev *rdev; + struct regmap *regmap; + int i, ret; + + regmap = devm_regmap_init_i2c(i2c, &isl9305_regmap); + if (IS_ERR(regmap)) { + ret = PTR_ERR(regmap); + dev_err(&i2c->dev, "Failed to create regmap: %d\n", ret); + return ret; + } + + config.dev = &i2c->dev; + + for (i = 0; i < ARRAY_SIZE(isl9305_regulators); i++) { + if (pdata) + config.init_data = pdata->init_data[i]; + else + config.init_data = NULL; + + rdev = devm_regulator_register(&i2c->dev, + &isl9305_regulators[i], + &config); + if (IS_ERR(rdev)) { + ret = PTR_ERR(rdev); + dev_err(&i2c->dev, "Failed to register %s: %d\n", + isl9305_regulators[i].name, ret); + return ret; + } + } + + return 0; +} + +#ifdef CONFIG_OF +static const struct of_device_id isl9305_dt_ids[] = { + { .compatible = "isl,isl9305" }, + { .compatible = "isl,isl9305h" }, + {}, +}; +#endif + +static const struct i2c_device_id isl9305_i2c_id[] = { + { "isl9305", }, + { "isl9305h", }, + { } +}; +MODULE_DEVICE_TABLE(i2c, isl9305_i2c_id); + +static struct i2c_driver isl9305_regulator_driver = { + .driver = { + .name = "isl9305", + .owner = THIS_MODULE, + .of_match_table = of_match_ptr(isl9305_dt_ids), + }, + .probe = isl9305_i2c_probe, + .id_table = isl9305_i2c_id, +}; + +module_i2c_driver(isl9305_regulator_driver); + +MODULE_AUTHOR("Mark Brown"); +MODULE_DESCRIPTION("Intersil ISL9305 DCDC regulator"); +MODULE_LICENSE("GPL"); diff --git a/drivers/regulator/ltc3589.c b/drivers/regulator/ltc3589.c index c756955..0ce8e4e 100644 --- a/drivers/regulator/ltc3589.c +++ b/drivers/regulator/ltc3589.c @@ -372,6 +372,7 @@ static bool ltc3589_volatile_reg(struct device *dev, unsigned int reg) switch (reg) { case LTC3589_IRQSTAT: case LTC3589_PGSTAT: + case LTC3589_VCCR: return true; } return false; diff --git a/drivers/regulator/max1586.c b/drivers/regulator/max1586.c index d23d057..86db310 100644 --- a/drivers/regulator/max1586.c +++ b/drivers/regulator/max1586.c @@ -24,6 +24,8 @@ #include <linux/regulator/driver.h> #include <linux/slab.h> #include <linux/regulator/max1586.h> +#include <linux/of_device.h> +#include <linux/regulator/of_regulator.h> #define MAX1586_V3_MAX_VSEL 31 #define MAX1586_V6_MAX_VSEL 3 @@ -157,13 +159,87 @@ static struct regulator_desc max1586_reg[] = { }, }; +static int of_get_max1586_platform_data(struct device *dev, + struct max1586_platform_data *pdata) +{ + struct max1586_subdev_data *sub; + struct of_regulator_match rmatch[ARRAY_SIZE(max1586_reg)]; + struct device_node *np = dev->of_node; + int i, matched; + + if (of_property_read_u32(np, "v3-gain", + &pdata->v3_gain) < 0) { + dev_err(dev, "%s has no 'v3-gain' property\n", np->full_name); + return -EINVAL; + } + + np = of_get_child_by_name(np, "regulators"); + if (!np) { + dev_err(dev, "missing 'regulators' subnode in DT\n"); + return -EINVAL; + } + + for (i = 0; i < ARRAY_SIZE(rmatch); i++) + rmatch[i].name = max1586_reg[i].name; + + matched = of_regulator_match(dev, np, rmatch, ARRAY_SIZE(rmatch)); + of_node_put(np); + /* + * If matched is 0, ie. neither Output_V3 nor Output_V6 have been found, + * return 0, which signals the normal situation where no subregulator is + * available. This is normal because the max1586 doesn't provide any + * readback support, so the subregulators can't report any status + * anyway. If matched < 0, return the error. + */ + if (matched <= 0) + return matched; + + pdata->subdevs = devm_kzalloc(dev, sizeof(struct max1586_subdev_data) * + matched, GFP_KERNEL); + if (!pdata->subdevs) + return -ENOMEM; + + pdata->num_subdevs = matched; + sub = pdata->subdevs; + + for (i = 0; i < matched; i++) { + sub->id = i; + sub->name = rmatch[i].of_node->name; + sub->platform_data = rmatch[i].init_data; + sub++; + } + + return 0; +} + +static const struct of_device_id max1586_of_match[] = { + { .compatible = "maxim,max1586", }, + {}, +}; +MODULE_DEVICE_TABLE(of, max1586_of_match); + static int max1586_pmic_probe(struct i2c_client *client, const struct i2c_device_id *i2c_id) { - struct max1586_platform_data *pdata = dev_get_platdata(&client->dev); + struct max1586_platform_data *pdata, pdata_of; struct regulator_config config = { }; struct max1586_data *max1586; - int i, id; + int i, id, ret; + const struct of_device_id *match; + + pdata = dev_get_platdata(&client->dev); + if (client->dev.of_node && !pdata) { + match = of_match_device(of_match_ptr(max1586_of_match), + &client->dev); + if (!match) { + dev_err(&client->dev, "Error: No device match found\n"); + return -ENODEV; + } + ret = of_get_max1586_platform_data(&client->dev, &pdata_of); + if (ret < 0) + return ret; + pdata = &pdata_of; + } max1586 = devm_kzalloc(&client->dev, sizeof(struct max1586_data), GFP_KERNEL); @@ -229,6 +305,7 @@ static struct i2c_driver max1586_pmic_driver = { .driver = { .name = "max1586", .owner = THIS_MODULE, + .of_match_table = of_match_ptr(max1586_of_match), }, .id_table = max1586_id, }; diff --git a/drivers/regulator/max77802.c b/drivers/regulator/max77802.c new file mode 100644 index 0000000..d89792b --- /dev/null +++ b/drivers/regulator/max77802.c @@ -0,0 +1,586 @@ +/* + * max77802.c - Regulator driver for the Maxim 77802 + * + * Copyright (C) 2013-2014 Google, Inc + * Simon Glass <sjg@chromium.org> + * + * Copyright (C) 2012 Samsung Electronics + * Chiwoong Byun <woong.byun@smasung.com> + * Jonghwa Lee <jonghwa3.lee@samsung.com> + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * This driver is based on max8997.c + */ + +#include <linux/kernel.h> +#include <linux/bug.h> +#include <linux/err.h> +#include <linux/gpio.h> +#include <linux/slab.h> +#include <linux/gpio/consumer.h> +#include <linux/platform_device.h> +#include <linux/regulator/driver.h> +#include <linux/regulator/machine.h> +#include <linux/regulator/of_regulator.h> +#include <linux/mfd/max77686.h> +#include <linux/mfd/max77686-private.h> + +/* Default ramp delay in case it is not manually set */ +#define MAX77802_RAMP_DELAY 100000 /* uV/us */ + +#define MAX77802_OPMODE_SHIFT_LDO 6 +#define MAX77802_OPMODE_BUCK234_SHIFT 4 +#define MAX77802_OPMODE_MASK 0x3 + +#define MAX77802_VSEL_MASK 0x3F +#define MAX77802_DVS_VSEL_MASK 0xFF + +#define MAX77802_RAMP_RATE_MASK_2BIT 0xC0 +#define MAX77802_RAMP_RATE_SHIFT_2BIT 6 +#define MAX77802_RAMP_RATE_MASK_4BIT 0xF0 +#define MAX77802_RAMP_RATE_SHIFT_4BIT 4 + +/* MAX77802 has two register formats: 2-bit and 4-bit */ +static const unsigned int ramp_table_77802_2bit[] = { + 12500, + 25000, + 50000, + 100000, +}; + +static unsigned int ramp_table_77802_4bit[] = { + 1000, 2000, 3030, 4000, + 5000, 5880, 7140, 8330, + 9090, 10000, 11110, 12500, + 16670, 25000, 50000, 100000, +}; + +struct max77802_regulator_prv { + unsigned int opmode[MAX77802_REG_MAX]; +}; + +static int max77802_get_opmode_shift(int id) +{ + if (id == MAX77802_BUCK1 || (id >= MAX77802_BUCK5 && + id <= MAX77802_BUCK10)) + return 0; + + if (id >= MAX77802_BUCK2 && id <= MAX77802_BUCK4) + return MAX77802_OPMODE_BUCK234_SHIFT; + + if (id >= MAX77802_LDO1 && id <= MAX77802_LDO35) + return MAX77802_OPMODE_SHIFT_LDO; + + return -EINVAL; +} + +/* + * Some BUCKS supports Normal[ON/OFF] mode during suspend + * + * BUCK 1, 6, 2-4, 5, 7-10 (all) + * + * The other mode (0x02) will make PWRREQ switch between normal + * and low power. + */ +static int max77802_buck_set_suspend_disable(struct regulator_dev *rdev) +{ + unsigned int val = MAX77802_OPMODE_STANDBY; + struct max77802_regulator_prv *max77802 = rdev_get_drvdata(rdev); + int id = rdev_get_id(rdev); + int shift = max77802_get_opmode_shift(id); + + max77802->opmode[id] = val; + return regmap_update_bits(rdev->regmap, rdev->desc->enable_reg, + rdev->desc->enable_mask, val << shift); +} + +/* + * Some LDOs supports LPM-ON/OFF/Normal-ON mode during suspend state + * (Enable Control Logic1 by PWRREQ) + * + * LDOs 2, 4-19, 22-35. + * + */ +static int max77802_ldo_set_suspend_mode_logic1(struct regulator_dev *rdev, + unsigned int mode) +{ + struct max77802_regulator_prv *max77802 = rdev_get_drvdata(rdev); + int id = rdev_get_id(rdev); + unsigned int val; + int shift = max77802_get_opmode_shift(id); + + switch (mode) { + case REGULATOR_MODE_IDLE: /* ON in LP Mode */ + val = MAX77802_OPMODE_LP; + break; + case REGULATOR_MODE_NORMAL: /* ON in Normal Mode */ + val = MAX77802_OPMODE_NORMAL; + break; + case REGULATOR_MODE_STANDBY: /* ON/OFF by PWRREQ */ + val = MAX77802_OPMODE_STANDBY; + break; + default: + dev_warn(&rdev->dev, "%s: regulator mode: 0x%x not supported\n", + rdev->desc->name, mode); + return -EINVAL; + } + + max77802->opmode[id] = val; + return regmap_update_bits(rdev->regmap, rdev->desc->enable_reg, + rdev->desc->enable_mask, val << shift); +} + +/* + * Mode 1 (Output[ON/OFF] by PWRREQ) is not supported on some LDOs + * (Enable Control Logic2 by PWRREQ) + * + * LDOs 1, 20, 21, and 3, + * + */ +static int max77802_ldo_set_suspend_mode_logic2(struct regulator_dev *rdev, + unsigned int mode) +{ + struct max77802_regulator_prv *max77802 = rdev_get_drvdata(rdev); + int id = rdev_get_id(rdev); + unsigned int val; + int shift = max77802_get_opmode_shift(id); + + switch (mode) { + case REGULATOR_MODE_IDLE: /* ON in LP Mode */ + val = MAX77802_OPMODE_LP; + break; + case REGULATOR_MODE_NORMAL: /* ON in Normal Mode */ + val = MAX77802_OPMODE_NORMAL; + break; + default: + dev_warn(&rdev->dev, "%s: regulator mode: 0x%x not supported\n", + rdev->desc->name, mode); + return -EINVAL; + } + + max77802->opmode[id] = val; + return regmap_update_bits(rdev->regmap, rdev->desc->enable_reg, + rdev->desc->enable_mask, val << shift); +} + +static int max77802_enable(struct regulator_dev *rdev) +{ + struct max77802_regulator_prv *max77802 = rdev_get_drvdata(rdev); + int id = rdev_get_id(rdev); + int shift = max77802_get_opmode_shift(id); + + return regmap_update_bits(rdev->regmap, rdev->desc->enable_reg, + rdev->desc->enable_mask, + max77802->opmode[id] << shift); +} + +static int max77802_find_ramp_value(struct regulator_dev *rdev, + const unsigned int limits[], int size, + unsigned int ramp_delay) +{ + int i; + + for (i = 0; i < size; i++) { + if (ramp_delay <= limits[i]) + return i; + } + + /* Use maximum value for no ramp control */ + dev_warn(&rdev->dev, "%s: ramp_delay: %d not supported, setting 100000\n", + rdev->desc->name, ramp_delay); + return size - 1; +} + +/* Used for BUCKs 2-4 */ +static int max77802_set_ramp_delay_2bit(struct regulator_dev *rdev, + int ramp_delay) +{ + int id = rdev_get_id(rdev); + unsigned int ramp_value; + + if (id > MAX77802_BUCK4) { + dev_warn(&rdev->dev, + "%s: regulator: ramp delay not supported\n", + rdev->desc->name); + return -EINVAL; + } + ramp_value = max77802_find_ramp_value(rdev, ramp_table_77802_2bit, + ARRAY_SIZE(ramp_table_77802_2bit), ramp_delay); + + return regmap_update_bits(rdev->regmap, rdev->desc->enable_reg, + MAX77802_RAMP_RATE_MASK_2BIT, + ramp_value << MAX77802_RAMP_RATE_SHIFT_2BIT); +} + +/* For BUCK1, 6 */ +static int max77802_set_ramp_delay_4bit(struct regulator_dev *rdev, + int ramp_delay) +{ + unsigned int ramp_value; + + ramp_value = max77802_find_ramp_value(rdev, ramp_table_77802_4bit, + ARRAY_SIZE(ramp_table_77802_4bit), ramp_delay); + + return regmap_update_bits(rdev->regmap, rdev->desc->enable_reg, + MAX77802_RAMP_RATE_MASK_4BIT, + ramp_value << MAX77802_RAMP_RATE_SHIFT_4BIT); +} + +/* + * LDOs 2, 4-19, 22-35 + */ +static struct regulator_ops max77802_ldo_ops_logic1 = { + .list_voltage = regulator_list_voltage_linear, + .map_voltage = regulator_map_voltage_linear, + .is_enabled = regulator_is_enabled_regmap, + .enable = max77802_enable, + .disable = regulator_disable_regmap, + .get_voltage_sel = regulator_get_voltage_sel_regmap, + .set_voltage_sel = regulator_set_voltage_sel_regmap, + .set_voltage_time_sel = regulator_set_voltage_time_sel, + .set_suspend_mode = max77802_ldo_set_suspend_mode_logic1, +}; + +/* + * LDOs 1, 20, 21, 3 + */ +static struct regulator_ops max77802_ldo_ops_logic2 = { + .list_voltage = regulator_list_voltage_linear, + .map_voltage = regulator_map_voltage_linear, + .is_enabled = regulator_is_enabled_regmap, + .enable = max77802_enable, + .disable = regulator_disable_regmap, + .get_voltage_sel = regulator_get_voltage_sel_regmap, + .set_voltage_sel = regulator_set_voltage_sel_regmap, + .set_voltage_time_sel = regulator_set_voltage_time_sel, + .set_suspend_mode = max77802_ldo_set_suspend_mode_logic2, +}; + +/* BUCKS 1, 6 */ +static struct regulator_ops max77802_buck_16_dvs_ops = { + .list_voltage = regulator_list_voltage_linear, + .map_voltage = regulator_map_voltage_linear, + .is_enabled = regulator_is_enabled_regmap, + .enable = max77802_enable, + .disable = regulator_disable_regmap, + .get_voltage_sel = regulator_get_voltage_sel_regmap, + .set_voltage_sel = regulator_set_voltage_sel_regmap, + .set_voltage_time_sel = regulator_set_voltage_time_sel, + .set_ramp_delay = max77802_set_ramp_delay_4bit, + .set_suspend_disable = max77802_buck_set_suspend_disable, +}; + +/* BUCKs 2-4, 5, 7-10 */ +static struct regulator_ops max77802_buck_dvs_ops = { + .list_voltage = regulator_list_voltage_linear, + .map_voltage = regulator_map_voltage_linear, + .is_enabled = regulator_is_enabled_regmap, + .enable = max77802_enable, + .disable = regulator_disable_regmap, + .get_voltage_sel = regulator_get_voltage_sel_regmap, + .set_voltage_sel = regulator_set_voltage_sel_regmap, + .set_voltage_time_sel = regulator_set_voltage_time_sel, + .set_ramp_delay = max77802_set_ramp_delay_2bit, + .set_suspend_disable = max77802_buck_set_suspend_disable, +}; + +/* LDOs 3-7, 9-14, 18-26, 28, 29, 32-34 */ +#define regulator_77802_desc_p_ldo(num, supply, log) { \ + .name = "LDO"#num, \ + .id = MAX77802_LDO##num, \ + .supply_name = "inl"#supply, \ + .ops = &max77802_ldo_ops_logic##log, \ + .type = REGULATOR_VOLTAGE, \ + .owner = THIS_MODULE, \ + .min_uV = 800000, \ + .uV_step = 50000, \ + .ramp_delay = MAX77802_RAMP_DELAY, \ + .n_voltages = 1 << 6, \ + .vsel_reg = MAX77802_REG_LDO1CTRL1 + num - 1, \ + .vsel_mask = MAX77802_VSEL_MASK, \ + .enable_reg = MAX77802_REG_LDO1CTRL1 + num - 1, \ + .enable_mask = MAX77802_OPMODE_MASK << MAX77802_OPMODE_SHIFT_LDO, \ +} + +/* LDOs 1, 2, 8, 15, 17, 27, 30, 35 */ +#define regulator_77802_desc_n_ldo(num, supply, log) { \ + .name = "LDO"#num, \ + .id = MAX77802_LDO##num, \ + .supply_name = "inl"#supply, \ + .ops = &max77802_ldo_ops_logic##log, \ + .type = REGULATOR_VOLTAGE, \ + .owner = THIS_MODULE, \ + .min_uV = 800000, \ + .uV_step = 25000, \ + .ramp_delay = MAX77802_RAMP_DELAY, \ + .n_voltages = 1 << 6, \ + .vsel_reg = MAX77802_REG_LDO1CTRL1 + num - 1, \ + .vsel_mask = MAX77802_VSEL_MASK, \ + .enable_reg = MAX77802_REG_LDO1CTRL1 + num - 1, \ + .enable_mask = MAX77802_OPMODE_MASK << MAX77802_OPMODE_SHIFT_LDO, \ +} + +/* BUCKs 1, 6 */ +#define regulator_77802_desc_16_buck(num) { \ + .name = "BUCK"#num, \ + .id = MAX77802_BUCK##num, \ + .supply_name = "inb"#num, \ + .ops = &max77802_buck_16_dvs_ops, \ + .type = REGULATOR_VOLTAGE, \ + .owner = THIS_MODULE, \ + .min_uV = 612500, \ + .uV_step = 6250, \ + .ramp_delay = MAX77802_RAMP_DELAY, \ + .n_voltages = 1 << 8, \ + .vsel_reg = MAX77802_REG_BUCK ## num ## DVS1, \ + .vsel_mask = MAX77802_DVS_VSEL_MASK, \ + .enable_reg = MAX77802_REG_BUCK ## num ## CTRL, \ + .enable_mask = MAX77802_OPMODE_MASK, \ +} + +/* BUCKS 2-4 */ +#define regulator_77802_desc_234_buck(num) { \ + .name = "BUCK"#num, \ + .id = MAX77802_BUCK##num, \ + .supply_name = "inb"#num, \ + .ops = &max77802_buck_dvs_ops, \ + .type = REGULATOR_VOLTAGE, \ + .owner = THIS_MODULE, \ + .min_uV = 600000, \ + .uV_step = 6250, \ + .ramp_delay = MAX77802_RAMP_DELAY, \ + .n_voltages = 0x91, \ + .vsel_reg = MAX77802_REG_BUCK ## num ## DVS1, \ + .vsel_mask = MAX77802_DVS_VSEL_MASK, \ + .enable_reg = MAX77802_REG_BUCK ## num ## CTRL1, \ + .enable_mask = MAX77802_OPMODE_MASK << \ + MAX77802_OPMODE_BUCK234_SHIFT, \ +} + +/* BUCK 5 */ +#define regulator_77802_desc_buck5(num) { \ + .name = "BUCK"#num, \ + .id = MAX77802_BUCK##num, \ + .supply_name = "inb"#num, \ + .ops = &max77802_buck_dvs_ops, \ + .type = REGULATOR_VOLTAGE, \ + .owner = THIS_MODULE, \ + .min_uV = 750000, \ + .uV_step = 50000, \ + .ramp_delay = MAX77802_RAMP_DELAY, \ + .n_voltages = 1 << 6, \ + .vsel_reg = MAX77802_REG_BUCK5OUT, \ + .vsel_mask = MAX77802_VSEL_MASK, \ + .enable_reg = MAX77802_REG_BUCK5CTRL, \ + .enable_mask = MAX77802_OPMODE_MASK, \ +} + +/* BUCKs 7-10 */ +#define regulator_77802_desc_buck7_10(num) { \ + .name = "BUCK"#num, \ + .id = MAX77802_BUCK##num, \ + .supply_name = "inb"#num, \ + .ops = &max77802_buck_dvs_ops, \ + .type = REGULATOR_VOLTAGE, \ + .owner = THIS_MODULE, \ + .min_uV = 750000, \ + .uV_step = 50000, \ + .ramp_delay = MAX77802_RAMP_DELAY, \ + .n_voltages = 1 << 6, \ + .vsel_reg = MAX77802_REG_BUCK7OUT + (num - 7) * 3, \ + .vsel_mask = MAX77802_VSEL_MASK, \ + .enable_reg = MAX77802_REG_BUCK7CTRL + (num - 7) * 3, \ + .enable_mask = MAX77802_OPMODE_MASK, \ +} + +static struct regulator_desc regulators[] = { + regulator_77802_desc_16_buck(1), + regulator_77802_desc_234_buck(2), + regulator_77802_desc_234_buck(3), + regulator_77802_desc_234_buck(4), + regulator_77802_desc_buck5(5), + regulator_77802_desc_16_buck(6), + regulator_77802_desc_buck7_10(7), + regulator_77802_desc_buck7_10(8), + regulator_77802_desc_buck7_10(9), + regulator_77802_desc_buck7_10(10), + regulator_77802_desc_n_ldo(1, 10, 2), + regulator_77802_desc_n_ldo(2, 10, 1), + regulator_77802_desc_p_ldo(3, 3, 2), + regulator_77802_desc_p_ldo(4, 6, 1), + regulator_77802_desc_p_ldo(5, 3, 1), + regulator_77802_desc_p_ldo(6, 3, 1), + regulator_77802_desc_p_ldo(7, 3, 1), + regulator_77802_desc_n_ldo(8, 1, 1), + regulator_77802_desc_p_ldo(9, 5, 1), + regulator_77802_desc_p_ldo(10, 4, 1), + regulator_77802_desc_p_ldo(11, 4, 1), + regulator_77802_desc_p_ldo(12, 9, 1), + regulator_77802_desc_p_ldo(13, 4, 1), + regulator_77802_desc_p_ldo(14, 4, 1), + regulator_77802_desc_n_ldo(15, 1, 1), + regulator_77802_desc_n_ldo(17, 2, 1), + regulator_77802_desc_p_ldo(18, 7, 1), + regulator_77802_desc_p_ldo(19, 5, 1), + regulator_77802_desc_p_ldo(20, 7, 2), + regulator_77802_desc_p_ldo(21, 6, 2), + regulator_77802_desc_p_ldo(23, 9, 1), + regulator_77802_desc_p_ldo(24, 6, 1), + regulator_77802_desc_p_ldo(25, 9, 1), + regulator_77802_desc_p_ldo(26, 9, 1), + regulator_77802_desc_n_ldo(27, 2, 1), + regulator_77802_desc_p_ldo(28, 7, 1), + regulator_77802_desc_p_ldo(29, 7, 1), + regulator_77802_desc_n_ldo(30, 2, 1), + regulator_77802_desc_p_ldo(32, 9, 1), + regulator_77802_desc_p_ldo(33, 6, 1), + regulator_77802_desc_p_ldo(34, 9, 1), + regulator_77802_desc_n_ldo(35, 2, 1), +}; + +#ifdef CONFIG_OF +static int max77802_pmic_dt_parse_pdata(struct platform_device *pdev, + struct max77686_platform_data *pdata) +{ + struct max77686_dev *iodev = dev_get_drvdata(pdev->dev.parent); + struct device_node *pmic_np, *regulators_np; + struct max77686_regulator_data *rdata; + struct of_regulator_match rmatch; + unsigned int i; + + pmic_np = iodev->dev->of_node; + regulators_np = of_get_child_by_name(pmic_np, "regulators"); + if (!regulators_np) { + dev_err(&pdev->dev, "could not find regulators sub-node\n"); + return -EINVAL; + } + + pdata->num_regulators = ARRAY_SIZE(regulators); + rdata = devm_kzalloc(&pdev->dev, sizeof(*rdata) * + pdata->num_regulators, GFP_KERNEL); + if (!rdata) { + of_node_put(regulators_np); + return -ENOMEM; + } + + for (i = 0; i < pdata->num_regulators; i++) { + rmatch.name = regulators[i].name; + rmatch.init_data = NULL; + rmatch.of_node = NULL; + if (of_regulator_match(&pdev->dev, regulators_np, &rmatch, + 1) != 1) { + dev_warn(&pdev->dev, "No matching regulator for '%s'\n", + rmatch.name); + continue; + } + rdata[i].initdata = rmatch.init_data; + rdata[i].of_node = rmatch.of_node; + rdata[i].id = regulators[i].id; + } + + pdata->regulators = rdata; + of_node_put(regulators_np); + + return 0; +} +#else +static int max77802_pmic_dt_parse_pdata(struct platform_device *pdev, + struct max77686_platform_data *pdata) +{ + return 0; +} +#endif /* CONFIG_OF */ + +static int max77802_pmic_probe(struct platform_device *pdev) +{ + struct max77686_dev *iodev = dev_get_drvdata(pdev->dev.parent); + struct max77686_platform_data *pdata = dev_get_platdata(iodev->dev); + struct max77802_regulator_prv *max77802; + int i, ret = 0, val; + struct regulator_config config = { }; + + /* This is allocated by the MFD driver */ + if (!pdata) { + dev_err(&pdev->dev, "no platform data found for regulator\n"); + return -ENODEV; + } + + max77802 = devm_kzalloc(&pdev->dev, + sizeof(struct max77802_regulator_prv), + GFP_KERNEL); + if (!max77802) + return -ENOMEM; + + if (iodev->dev->of_node) { + ret = max77802_pmic_dt_parse_pdata(pdev, pdata); + if (ret) + return ret; + } + + config.dev = iodev->dev; + config.regmap = iodev->regmap; + config.driver_data = max77802; + platform_set_drvdata(pdev, max77802); + + for (i = 0; i < MAX77802_REG_MAX; i++) { + struct regulator_dev *rdev; + int id = pdata->regulators[i].id; + int shift = max77802_get_opmode_shift(id); + + config.init_data = pdata->regulators[i].initdata; + config.of_node = pdata->regulators[i].of_node; + + ret = regmap_read(iodev->regmap, regulators[i].enable_reg, &val); + val = val >> shift & MAX77802_OPMODE_MASK; + + /* + * If the regulator is disabled and the system warm rebooted, + * the hardware reports OFF as the regulator operating mode. + * Default to operating mode NORMAL in that case. + */ + if (val == MAX77802_OPMODE_OFF) + max77802->opmode[id] = MAX77802_OPMODE_NORMAL; + else + max77802->opmode[id] = val; + + rdev = devm_regulator_register(&pdev->dev, + ®ulators[i], &config); + if (IS_ERR(rdev)) { + dev_err(&pdev->dev, + "regulator init failed for %d\n", i); + return PTR_ERR(rdev); + } + } + + return 0; +} + +static const struct platform_device_id max77802_pmic_id[] = { + {"max77802-pmic", 0}, + { }, +}; +MODULE_DEVICE_TABLE(platform, max77802_pmic_id); + +static struct platform_driver max77802_pmic_driver = { + .driver = { + .name = "max77802-pmic", + .owner = THIS_MODULE, + }, + .probe = max77802_pmic_probe, + .id_table = max77802_pmic_id, +}; + +module_platform_driver(max77802_pmic_driver); + +MODULE_DESCRIPTION("MAXIM 77802 Regulator Driver"); +MODULE_AUTHOR("Simon Glass <sjg@chromium.org>"); +MODULE_LICENSE("GPL"); diff --git a/drivers/regulator/mc13892-regulator.c b/drivers/regulator/mc13892-regulator.c index f374fa5..793b662 100644 --- a/drivers/regulator/mc13892-regulator.c +++ b/drivers/regulator/mc13892-regulator.c @@ -526,6 +526,7 @@ static unsigned int mc13892_vcam_get_mode(struct regulator_dev *rdev) return REGULATOR_MODE_NORMAL; } +static struct regulator_ops mc13892_vcam_ops; static int mc13892_regulator_probe(struct platform_device *pdev) { @@ -582,10 +583,12 @@ static int mc13892_regulator_probe(struct platform_device *pdev) } mc13xxx_unlock(mc13892); - mc13892_regulators[MC13892_VCAM].desc.ops->set_mode - = mc13892_vcam_set_mode; - mc13892_regulators[MC13892_VCAM].desc.ops->get_mode - = mc13892_vcam_get_mode; + /* update mc13892_vcam ops */ + memcpy(&mc13892_vcam_ops, mc13892_regulators[MC13892_VCAM].desc.ops, + sizeof(struct regulator_ops)); + mc13892_vcam_ops.set_mode = mc13892_vcam_set_mode, + mc13892_vcam_ops.get_mode = mc13892_vcam_get_mode, + mc13892_regulators[MC13892_VCAM].desc.ops = &mc13892_vcam_ops; mc13xxx_data = mc13xxx_parse_regulators_dt(pdev, mc13892_regulators, ARRAY_SIZE(mc13892_regulators)); diff --git a/drivers/regulator/of_regulator.c b/drivers/regulator/of_regulator.c index ee5e67b..7a51814 100644 --- a/drivers/regulator/of_regulator.c +++ b/drivers/regulator/of_regulator.c @@ -14,8 +14,11 @@ #include <linux/slab.h> #include <linux/of.h> #include <linux/regulator/machine.h> +#include <linux/regulator/driver.h> #include <linux/regulator/of_regulator.h> +#include "internal.h" + static void of_get_regulation_constraints(struct device_node *np, struct regulator_init_data **init_data) { @@ -189,3 +192,51 @@ int of_regulator_match(struct device *dev, struct device_node *node, return count; } EXPORT_SYMBOL_GPL(of_regulator_match); + +struct regulator_init_data *regulator_of_get_init_data(struct device *dev, + const struct regulator_desc *desc, + struct device_node **node) +{ + struct device_node *search, *child; + struct regulator_init_data *init_data = NULL; + const char *name; + + if (!dev->of_node || !desc->of_match) + return NULL; + + if (desc->regulators_node) + search = of_get_child_by_name(dev->of_node, + desc->regulators_node); + else + search = dev->of_node; + + if (!search) { + dev_err(dev, "Failed to find regulator container node\n"); + return NULL; + } + + for_each_child_of_node(search, child) { + name = of_get_property(child, "regulator-compatible", NULL); + if (!name) + name = child->name; + + if (strcmp(desc->of_match, name)) + continue; + + init_data = of_get_regulator_init_data(dev, child); + if (!init_data) { + dev_err(dev, + "failed to parse DT for regulator %s\n", + child->name); + break; + } + + of_node_get(child); + *node = child; + break; + } + + of_node_put(search); + + return init_data; +} diff --git a/drivers/regulator/pwm-regulator.c b/drivers/regulator/pwm-regulator.c new file mode 100644 index 0000000..d3f55ea --- /dev/null +++ b/drivers/regulator/pwm-regulator.c @@ -0,0 +1,197 @@ +/* + * Regulator driver for PWM Regulators + * + * Copyright (C) 2014 - STMicroelectronics Inc. + * + * Author: Lee Jones <lee.jones@linaro.org> + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + */ + +#include <linux/module.h> +#include <linux/init.h> +#include <linux/err.h> +#include <linux/regulator/driver.h> +#include <linux/regulator/machine.h> +#include <linux/regulator/of_regulator.h> +#include <linux/of.h> +#include <linux/of_device.h> +#include <linux/pwm.h> + +struct pwm_regulator_data { + struct regulator_desc desc; + struct pwm_voltages *duty_cycle_table; + struct pwm_device *pwm; + bool enabled; + int state; +}; + +struct pwm_voltages { + unsigned int uV; + unsigned int dutycycle; +}; + +static int pwm_regulator_get_voltage_sel(struct regulator_dev *dev) +{ + struct pwm_regulator_data *drvdata = rdev_get_drvdata(dev); + + return drvdata->state; +} + +static int pwm_regulator_set_voltage_sel(struct regulator_dev *dev, + unsigned selector) +{ + struct pwm_regulator_data *drvdata = rdev_get_drvdata(dev); + unsigned int pwm_reg_period; + int dutycycle; + int ret; + + pwm_reg_period = pwm_get_period(drvdata->pwm); + + dutycycle = (pwm_reg_period * + drvdata->duty_cycle_table[selector].dutycycle) / 100; + + ret = pwm_config(drvdata->pwm, dutycycle, pwm_reg_period); + if (ret) { + dev_err(&dev->dev, "Failed to configure PWM\n"); + return ret; + } + + drvdata->state = selector; + + if (!drvdata->enabled) { + ret = pwm_enable(drvdata->pwm); + if (ret) { + dev_err(&dev->dev, "Failed to enable PWM\n"); + return ret; + } + drvdata->enabled = true; + } + + return 0; +} + +static int pwm_regulator_list_voltage(struct regulator_dev *dev, + unsigned selector) +{ + struct pwm_regulator_data *drvdata = rdev_get_drvdata(dev); + + if (selector >= drvdata->desc.n_voltages) + return -EINVAL; + + return drvdata->duty_cycle_table[selector].uV; +} + +static struct regulator_ops pwm_regulator_voltage_ops = { + .set_voltage_sel = pwm_regulator_set_voltage_sel, + .get_voltage_sel = pwm_regulator_get_voltage_sel, + .list_voltage = pwm_regulator_list_voltage, + .map_voltage = regulator_map_voltage_iterate, +}; + +static const struct regulator_desc pwm_regulator_desc = { + .name = "pwm-regulator", + .ops = &pwm_regulator_voltage_ops, + .type = REGULATOR_VOLTAGE, + .owner = THIS_MODULE, + .supply_name = "pwm", +}; + +static int pwm_regulator_probe(struct platform_device *pdev) +{ + struct pwm_regulator_data *drvdata; + struct property *prop; + struct regulator_dev *regulator; + struct regulator_config config = { }; + struct device_node *np = pdev->dev.of_node; + int length, ret; + + if (!np) { + dev_err(&pdev->dev, "Device Tree node missing\n"); + return -EINVAL; + } + + drvdata = devm_kzalloc(&pdev->dev, sizeof(*drvdata), GFP_KERNEL); + if (!drvdata) + return -ENOMEM; + + memcpy(&drvdata->desc, &pwm_regulator_desc, sizeof(pwm_regulator_desc)); + + /* determine the number of voltage-table */ + prop = of_find_property(np, "voltage-table", &length); + if (!prop) { + dev_err(&pdev->dev, "No voltage-table\n"); + return -EINVAL; + } + + if ((length < sizeof(*drvdata->duty_cycle_table)) || + (length % sizeof(*drvdata->duty_cycle_table))) { + dev_err(&pdev->dev, "voltage-table length(%d) is invalid\n", + length); + return -EINVAL; + } + + drvdata->desc.n_voltages = length / sizeof(*drvdata->duty_cycle_table); + + drvdata->duty_cycle_table = devm_kzalloc(&pdev->dev, + length, GFP_KERNEL); + if (!drvdata->duty_cycle_table) + return -ENOMEM; + + /* read voltage table from DT property */ + ret = of_property_read_u32_array(np, "voltage-table", + (u32 *)drvdata->duty_cycle_table, + length / sizeof(u32)); + if (ret < 0) { + dev_err(&pdev->dev, "read voltage-table failed\n"); + return ret; + } + + config.init_data = of_get_regulator_init_data(&pdev->dev, np); + if (!config.init_data) + return -ENOMEM; + + config.of_node = np; + config.dev = &pdev->dev; + config.driver_data = drvdata; + + drvdata->pwm = devm_pwm_get(&pdev->dev, NULL); + if (IS_ERR(drvdata->pwm)) { + dev_err(&pdev->dev, "Failed to get PWM\n"); + return PTR_ERR(drvdata->pwm); + } + + regulator = devm_regulator_register(&pdev->dev, + &drvdata->desc, &config); + if (IS_ERR(regulator)) { + dev_err(&pdev->dev, "Failed to register regulator %s\n", + drvdata->desc.name); + return PTR_ERR(regulator); + } + + return 0; +} + +static const struct of_device_id pwm_of_match[] = { + { .compatible = "pwm-regulator" }, + { }, +}; +MODULE_DEVICE_TABLE(of, pwm_of_match); + +static struct platform_driver pwm_regulator_driver = { + .driver = { + .name = "pwm-regulator", + .owner = THIS_MODULE, + .of_match_table = of_match_ptr(pwm_of_match), + }, + .probe = pwm_regulator_probe, +}; + +module_platform_driver(pwm_regulator_driver); + +MODULE_LICENSE("GPL"); +MODULE_AUTHOR("Lee Jones <lee.jones@linaro.org>"); +MODULE_DESCRIPTION("PWM Regulator Driver"); +MODULE_ALIAS("platform:pwm-regulator"); diff --git a/drivers/regulator/qcom_rpm-regulator.c b/drivers/regulator/qcom_rpm-regulator.c new file mode 100644 index 0000000..b55cd5b --- /dev/null +++ b/drivers/regulator/qcom_rpm-regulator.c @@ -0,0 +1,798 @@ +/* + * Copyright (c) 2014, Sony Mobile Communications AB. + * Copyright (c) 2012-2013, The Linux Foundation. All rights reserved. + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 and + * only version 2 as published by the Free Software Foundation. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + */ + +#include <linux/module.h> +#include <linux/platform_device.h> +#include <linux/of.h> +#include <linux/of_device.h> +#include <linux/regulator/driver.h> +#include <linux/regulator/machine.h> +#include <linux/regulator/of_regulator.h> +#include <linux/mfd/qcom_rpm.h> + +#include <dt-bindings/mfd/qcom-rpm.h> + +#define MAX_REQUEST_LEN 2 + +struct request_member { + int word; + unsigned int mask; + int shift; +}; + +struct rpm_reg_parts { + struct request_member mV; /* used if voltage is in mV */ + struct request_member uV; /* used if voltage is in uV */ + struct request_member ip; /* peak current in mA */ + struct request_member pd; /* pull down enable */ + struct request_member ia; /* average current in mA */ + struct request_member fm; /* force mode */ + struct request_member pm; /* power mode */ + struct request_member pc; /* pin control */ + struct request_member pf; /* pin function */ + struct request_member enable_state; /* NCP and switch */ + struct request_member comp_mode; /* NCP */ + struct request_member freq; /* frequency: NCP and SMPS */ + struct request_member freq_clk_src; /* clock source: SMPS */ + struct request_member hpm; /* switch: control OCP and SS */ + int request_len; +}; + +#define FORCE_MODE_IS_2_BITS(reg) \ + (((reg)->parts->fm.mask >> (reg)->parts->fm.shift) == 3) + +struct qcom_rpm_reg { + struct qcom_rpm *rpm; + + struct mutex lock; + struct device *dev; + struct regulator_desc desc; + const struct rpm_reg_parts *parts; + + int resource; + u32 val[MAX_REQUEST_LEN]; + + int uV; + int is_enabled; + + bool supports_force_mode_auto; + bool supports_force_mode_bypass; +}; + +static const struct rpm_reg_parts rpm8660_ldo_parts = { + .request_len = 2, + .mV = { 0, 0x00000FFF, 0 }, + .ip = { 0, 0x00FFF000, 12 }, + .fm = { 0, 0x03000000, 24 }, + .pc = { 0, 0x3C000000, 26 }, + .pf = { 0, 0xC0000000, 30 }, + .pd = { 1, 0x00000001, 0 }, + .ia = { 1, 0x00001FFE, 1 }, +}; + +static const struct rpm_reg_parts rpm8660_smps_parts = { + .request_len = 2, + .mV = { 0, 0x00000FFF, 0 }, + .ip = { 0, 0x00FFF000, 12 }, + .fm = { 0, 0x03000000, 24 }, + .pc = { 0, 0x3C000000, 26 }, + .pf = { 0, 0xC0000000, 30 }, + .pd = { 1, 0x00000001, 0 }, + .ia = { 1, 0x00001FFE, 1 }, + .freq = { 1, 0x001FE000, 13 }, + .freq_clk_src = { 1, 0x00600000, 21 }, +}; + +static const struct rpm_reg_parts rpm8660_switch_parts = { + .request_len = 1, + .enable_state = { 0, 0x00000001, 0 }, + .pd = { 0, 0x00000002, 1 }, + .pc = { 0, 0x0000003C, 2 }, + .pf = { 0, 0x000000C0, 6 }, + .hpm = { 0, 0x00000300, 8 }, +}; + +static const struct rpm_reg_parts rpm8660_ncp_parts = { + .request_len = 1, + .mV = { 0, 0x00000FFF, 0 }, + .enable_state = { 0, 0x00001000, 12 }, + .comp_mode = { 0, 0x00002000, 13 }, + .freq = { 0, 0x003FC000, 14 }, +}; + +static const struct rpm_reg_parts rpm8960_ldo_parts = { + .request_len = 2, + .uV = { 0, 0x007FFFFF, 0 }, + .pd = { 0, 0x00800000, 23 }, + .pc = { 0, 0x0F000000, 24 }, + .pf = { 0, 0xF0000000, 28 }, + .ip = { 1, 0x000003FF, 0 }, + .ia = { 1, 0x000FFC00, 10 }, + .fm = { 1, 0x00700000, 20 }, +}; + +static const struct rpm_reg_parts rpm8960_smps_parts = { + .request_len = 2, + .uV = { 0, 0x007FFFFF, 0 }, + .pd = { 0, 0x00800000, 23 }, + .pc = { 0, 0x0F000000, 24 }, + .pf = { 0, 0xF0000000, 28 }, + .ip = { 1, 0x000003FF, 0 }, + .ia = { 1, 0x000FFC00, 10 }, + .fm = { 1, 0x00700000, 20 }, + .pm = { 1, 0x00800000, 23 }, + .freq = { 1, 0x1F000000, 24 }, + .freq_clk_src = { 1, 0x60000000, 29 }, +}; + +static const struct rpm_reg_parts rpm8960_switch_parts = { + .request_len = 1, + .enable_state = { 0, 0x00000001, 0 }, + .pd = { 0, 0x00000002, 1 }, + .pc = { 0, 0x0000003C, 2 }, + .pf = { 0, 0x000003C0, 6 }, + .hpm = { 0, 0x00000C00, 10 }, +}; + +static const struct rpm_reg_parts rpm8960_ncp_parts = { + .request_len = 1, + .uV = { 0, 0x007FFFFF, 0 }, + .enable_state = { 0, 0x00800000, 23 }, + .comp_mode = { 0, 0x01000000, 24 }, + .freq = { 0, 0x3E000000, 25 }, +}; + +/* + * Physically available PMIC regulator voltage ranges + */ +static const struct regulator_linear_range pldo_ranges[] = { + REGULATOR_LINEAR_RANGE( 750000, 0, 59, 12500), + REGULATOR_LINEAR_RANGE(1500000, 60, 123, 25000), + REGULATOR_LINEAR_RANGE(3100000, 124, 160, 50000), +}; + +static const struct regulator_linear_range nldo_ranges[] = { + REGULATOR_LINEAR_RANGE( 750000, 0, 63, 12500), +}; + +static const struct regulator_linear_range nldo1200_ranges[] = { + REGULATOR_LINEAR_RANGE( 375000, 0, 59, 6250), + REGULATOR_LINEAR_RANGE( 750000, 60, 123, 12500), +}; + +static const struct regulator_linear_range smps_ranges[] = { + REGULATOR_LINEAR_RANGE( 375000, 0, 29, 12500), + REGULATOR_LINEAR_RANGE( 750000, 30, 89, 12500), + REGULATOR_LINEAR_RANGE(1500000, 90, 153, 25000), +}; + +static const struct regulator_linear_range ftsmps_ranges[] = { + REGULATOR_LINEAR_RANGE( 350000, 0, 6, 50000), + REGULATOR_LINEAR_RANGE( 700000, 7, 63, 12500), + REGULATOR_LINEAR_RANGE(1500000, 64, 100, 50000), +}; + +static const struct regulator_linear_range ncp_ranges[] = { + REGULATOR_LINEAR_RANGE(1500000, 0, 31, 50000), +}; + +static int rpm_reg_write(struct qcom_rpm_reg *vreg, + const struct request_member *req, + const int value) +{ + if (WARN_ON((value << req->shift) & ~req->mask)) + return -EINVAL; + + vreg->val[req->word] &= ~req->mask; + vreg->val[req->word] |= value << req->shift; + + return qcom_rpm_write(vreg->rpm, + vreg->resource, + vreg->val, + vreg->parts->request_len); +} + +static int rpm_reg_set_mV_sel(struct regulator_dev *rdev, + unsigned selector) +{ + struct qcom_rpm_reg *vreg = rdev_get_drvdata(rdev); + const struct rpm_reg_parts *parts = vreg->parts; + const struct request_member *req = &parts->mV; + int ret = 0; + int uV; + + if (req->mask == 0) + return -EINVAL; + + uV = regulator_list_voltage_linear_range(rdev, selector); + if (uV < 0) + return uV; + + mutex_lock(&vreg->lock); + vreg->uV = uV; + if (vreg->is_enabled) + ret = rpm_reg_write(vreg, req, vreg->uV / 1000); + mutex_unlock(&vreg->lock); + + return ret; +} + +static int rpm_reg_set_uV_sel(struct regulator_dev *rdev, + unsigned selector) +{ + struct qcom_rpm_reg *vreg = rdev_get_drvdata(rdev); + const struct rpm_reg_parts *parts = vreg->parts; + const struct request_member *req = &parts->uV; + int ret = 0; + int uV; + + if (req->mask == 0) + return -EINVAL; + + uV = regulator_list_voltage_linear_range(rdev, selector); + if (uV < 0) + return uV; + + mutex_lock(&vreg->lock); + vreg->uV = uV; + if (vreg->is_enabled) + ret = rpm_reg_write(vreg, req, vreg->uV); + mutex_unlock(&vreg->lock); + + return ret; +} + +static int rpm_reg_get_voltage(struct regulator_dev *rdev) +{ + struct qcom_rpm_reg *vreg = rdev_get_drvdata(rdev); + + return vreg->uV; +} + +static int rpm_reg_mV_enable(struct regulator_dev *rdev) +{ + struct qcom_rpm_reg *vreg = rdev_get_drvdata(rdev); + const struct rpm_reg_parts *parts = vreg->parts; + const struct request_member *req = &parts->mV; + int ret; + + if (req->mask == 0) + return -EINVAL; + + mutex_lock(&vreg->lock); + ret = rpm_reg_write(vreg, req, vreg->uV / 1000); + if (!ret) + vreg->is_enabled = 1; + mutex_unlock(&vreg->lock); + + return ret; +} + +static int rpm_reg_uV_enable(struct regulator_dev *rdev) +{ + struct qcom_rpm_reg *vreg = rdev_get_drvdata(rdev); + const struct rpm_reg_parts *parts = vreg->parts; + const struct request_member *req = &parts->uV; + int ret; + + if (req->mask == 0) + return -EINVAL; + + mutex_lock(&vreg->lock); + ret = rpm_reg_write(vreg, req, vreg->uV); + if (!ret) + vreg->is_enabled = 1; + mutex_unlock(&vreg->lock); + + return ret; +} + +static int rpm_reg_switch_enable(struct regulator_dev *rdev) +{ + struct qcom_rpm_reg *vreg = rdev_get_drvdata(rdev); + const struct rpm_reg_parts *parts = vreg->parts; + const struct request_member *req = &parts->enable_state; + int ret; + + if (req->mask == 0) + return -EINVAL; + + mutex_lock(&vreg->lock); + ret = rpm_reg_write(vreg, req, 1); + if (!ret) + vreg->is_enabled = 1; + mutex_unlock(&vreg->lock); + + return ret; +} + +static int rpm_reg_mV_disable(struct regulator_dev *rdev) +{ + struct qcom_rpm_reg *vreg = rdev_get_drvdata(rdev); + const struct rpm_reg_parts *parts = vreg->parts; + const struct request_member *req = &parts->mV; + int ret; + + if (req->mask == 0) + return -EINVAL; + + mutex_lock(&vreg->lock); + ret = rpm_reg_write(vreg, req, 0); + if (!ret) + vreg->is_enabled = 0; + mutex_unlock(&vreg->lock); + + return ret; +} + +static int rpm_reg_uV_disable(struct regulator_dev *rdev) +{ + struct qcom_rpm_reg *vreg = rdev_get_drvdata(rdev); + const struct rpm_reg_parts *parts = vreg->parts; + const struct request_member *req = &parts->uV; + int ret; + + if (req->mask == 0) + return -EINVAL; + + mutex_lock(&vreg->lock); + ret = rpm_reg_write(vreg, req, 0); + if (!ret) + vreg->is_enabled = 0; + mutex_unlock(&vreg->lock); + + return ret; +} + +static int rpm_reg_switch_disable(struct regulator_dev *rdev) +{ + struct qcom_rpm_reg *vreg = rdev_get_drvdata(rdev); + const struct rpm_reg_parts *parts = vreg->parts; + const struct request_member *req = &parts->enable_state; + int ret; + + if (req->mask == 0) + return -EINVAL; + + mutex_lock(&vreg->lock); + ret = rpm_reg_write(vreg, req, 0); + if (!ret) + vreg->is_enabled = 0; + mutex_unlock(&vreg->lock); + + return ret; +} + +static int rpm_reg_is_enabled(struct regulator_dev *rdev) +{ + struct qcom_rpm_reg *vreg = rdev_get_drvdata(rdev); + + return vreg->is_enabled; +} + +static struct regulator_ops uV_ops = { + .list_voltage = regulator_list_voltage_linear_range, + + .set_voltage_sel = rpm_reg_set_uV_sel, + .get_voltage = rpm_reg_get_voltage, + + .enable = rpm_reg_uV_enable, + .disable = rpm_reg_uV_disable, + .is_enabled = rpm_reg_is_enabled, +}; + +static struct regulator_ops mV_ops = { + .list_voltage = regulator_list_voltage_linear_range, + + .set_voltage_sel = rpm_reg_set_mV_sel, + .get_voltage = rpm_reg_get_voltage, + + .enable = rpm_reg_mV_enable, + .disable = rpm_reg_mV_disable, + .is_enabled = rpm_reg_is_enabled, +}; + +static struct regulator_ops switch_ops = { + .enable = rpm_reg_switch_enable, + .disable = rpm_reg_switch_disable, + .is_enabled = rpm_reg_is_enabled, +}; + +/* + * PM8058 regulators + */ +static const struct qcom_rpm_reg pm8058_pldo = { + .desc.linear_ranges = pldo_ranges, + .desc.n_linear_ranges = ARRAY_SIZE(pldo_ranges), + .desc.n_voltages = 161, + .desc.ops = &mV_ops, + .parts = &rpm8660_ldo_parts, + .supports_force_mode_auto = false, + .supports_force_mode_bypass = false, +}; + +static const struct qcom_rpm_reg pm8058_nldo = { + .desc.linear_ranges = nldo_ranges, + .desc.n_linear_ranges = ARRAY_SIZE(nldo_ranges), + .desc.n_voltages = 64, + .desc.ops = &mV_ops, + .parts = &rpm8660_ldo_parts, + .supports_force_mode_auto = false, + .supports_force_mode_bypass = false, +}; + +static const struct qcom_rpm_reg pm8058_smps = { + .desc.linear_ranges = smps_ranges, + .desc.n_linear_ranges = ARRAY_SIZE(smps_ranges), + .desc.n_voltages = 154, + .desc.ops = &mV_ops, + .parts = &rpm8660_smps_parts, + .supports_force_mode_auto = false, + .supports_force_mode_bypass = false, +}; + +static const struct qcom_rpm_reg pm8058_ncp = { + .desc.linear_ranges = ncp_ranges, + .desc.n_linear_ranges = ARRAY_SIZE(ncp_ranges), + .desc.n_voltages = 32, + .desc.ops = &mV_ops, + .parts = &rpm8660_ncp_parts, +}; + +static const struct qcom_rpm_reg pm8058_switch = { + .desc.ops = &switch_ops, + .parts = &rpm8660_switch_parts, +}; + +/* + * PM8901 regulators + */ +static const struct qcom_rpm_reg pm8901_pldo = { + .desc.linear_ranges = pldo_ranges, + .desc.n_linear_ranges = ARRAY_SIZE(pldo_ranges), + .desc.n_voltages = 161, + .desc.ops = &mV_ops, + .parts = &rpm8660_ldo_parts, + .supports_force_mode_auto = false, + .supports_force_mode_bypass = true, +}; + +static const struct qcom_rpm_reg pm8901_nldo = { + .desc.linear_ranges = nldo_ranges, + .desc.n_linear_ranges = ARRAY_SIZE(nldo_ranges), + .desc.n_voltages = 64, + .desc.ops = &mV_ops, + .parts = &rpm8660_ldo_parts, + .supports_force_mode_auto = false, + .supports_force_mode_bypass = true, +}; + +static const struct qcom_rpm_reg pm8901_ftsmps = { + .desc.linear_ranges = ftsmps_ranges, + .desc.n_linear_ranges = ARRAY_SIZE(ftsmps_ranges), + .desc.n_voltages = 101, + .desc.ops = &mV_ops, + .parts = &rpm8660_smps_parts, + .supports_force_mode_auto = true, + .supports_force_mode_bypass = false, +}; + +static const struct qcom_rpm_reg pm8901_switch = { + .desc.ops = &switch_ops, + .parts = &rpm8660_switch_parts, +}; + +/* + * PM8921 regulators + */ +static const struct qcom_rpm_reg pm8921_pldo = { + .desc.linear_ranges = pldo_ranges, + .desc.n_linear_ranges = ARRAY_SIZE(pldo_ranges), + .desc.n_voltages = 161, + .desc.ops = &uV_ops, + .parts = &rpm8960_ldo_parts, + .supports_force_mode_auto = false, + .supports_force_mode_bypass = true, +}; + +static const struct qcom_rpm_reg pm8921_nldo = { + .desc.linear_ranges = nldo_ranges, + .desc.n_linear_ranges = ARRAY_SIZE(nldo_ranges), + .desc.n_voltages = 64, + .desc.ops = &uV_ops, + .parts = &rpm8960_ldo_parts, + .supports_force_mode_auto = false, + .supports_force_mode_bypass = true, +}; + +static const struct qcom_rpm_reg pm8921_nldo1200 = { + .desc.linear_ranges = nldo1200_ranges, + .desc.n_linear_ranges = ARRAY_SIZE(nldo1200_ranges), + .desc.n_voltages = 124, + .desc.ops = &uV_ops, + .parts = &rpm8960_ldo_parts, + .supports_force_mode_auto = false, + .supports_force_mode_bypass = true, +}; + +static const struct qcom_rpm_reg pm8921_smps = { + .desc.linear_ranges = smps_ranges, + .desc.n_linear_ranges = ARRAY_SIZE(smps_ranges), + .desc.n_voltages = 154, + .desc.ops = &uV_ops, + .parts = &rpm8960_smps_parts, + .supports_force_mode_auto = true, + .supports_force_mode_bypass = false, +}; + +static const struct qcom_rpm_reg pm8921_ftsmps = { + .desc.linear_ranges = ftsmps_ranges, + .desc.n_linear_ranges = ARRAY_SIZE(ftsmps_ranges), + .desc.n_voltages = 101, + .desc.ops = &uV_ops, + .parts = &rpm8960_smps_parts, + .supports_force_mode_auto = true, + .supports_force_mode_bypass = false, +}; + +static const struct qcom_rpm_reg pm8921_ncp = { + .desc.linear_ranges = ncp_ranges, + .desc.n_linear_ranges = ARRAY_SIZE(ncp_ranges), + .desc.n_voltages = 32, + .desc.ops = &uV_ops, + .parts = &rpm8960_ncp_parts, +}; + +static const struct qcom_rpm_reg pm8921_switch = { + .desc.ops = &switch_ops, + .parts = &rpm8960_switch_parts, +}; + +static const struct of_device_id rpm_of_match[] = { + { .compatible = "qcom,rpm-pm8058-pldo", .data = &pm8058_pldo }, + { .compatible = "qcom,rpm-pm8058-nldo", .data = &pm8058_nldo }, + { .compatible = "qcom,rpm-pm8058-smps", .data = &pm8058_smps }, + { .compatible = "qcom,rpm-pm8058-ncp", .data = &pm8058_ncp }, + { .compatible = "qcom,rpm-pm8058-switch", .data = &pm8058_switch }, + + { .compatible = "qcom,rpm-pm8901-pldo", .data = &pm8901_pldo }, + { .compatible = "qcom,rpm-pm8901-nldo", .data = &pm8901_nldo }, + { .compatible = "qcom,rpm-pm8901-ftsmps", .data = &pm8901_ftsmps }, + { .compatible = "qcom,rpm-pm8901-switch", .data = &pm8901_switch }, + + { .compatible = "qcom,rpm-pm8921-pldo", .data = &pm8921_pldo }, + { .compatible = "qcom,rpm-pm8921-nldo", .data = &pm8921_nldo }, + { .compatible = "qcom,rpm-pm8921-nldo1200", .data = &pm8921_nldo1200 }, + { .compatible = "qcom,rpm-pm8921-smps", .data = &pm8921_smps }, + { .compatible = "qcom,rpm-pm8921-ftsmps", .data = &pm8921_ftsmps }, + { .compatible = "qcom,rpm-pm8921-ncp", .data = &pm8921_ncp }, + { .compatible = "qcom,rpm-pm8921-switch", .data = &pm8921_switch }, + { } +}; +MODULE_DEVICE_TABLE(of, rpm_of_match); + +static int rpm_reg_set(struct qcom_rpm_reg *vreg, + const struct request_member *req, + const int value) +{ + if (req->mask == 0 || (value << req->shift) & ~req->mask) + return -EINVAL; + + vreg->val[req->word] &= ~req->mask; + vreg->val[req->word] |= value << req->shift; + + return 0; +} + +static int rpm_reg_of_parse_freq(struct device *dev, struct qcom_rpm_reg *vreg) +{ + static const int freq_table[] = { + 19200000, 9600000, 6400000, 4800000, 3840000, 3200000, 2740000, + 2400000, 2130000, 1920000, 1750000, 1600000, 1480000, 1370000, + 1280000, 1200000, + + }; + const char *key; + u32 freq; + int ret; + int i; + + key = "qcom,switch-mode-frequency"; + ret = of_property_read_u32(dev->of_node, key, &freq); + if (ret) { + dev_err(dev, "regulator requires %s property\n", key); + return -EINVAL; + } + + for (i = 0; i < ARRAY_SIZE(freq_table); i++) { + if (freq == freq_table[i]) { + rpm_reg_set(vreg, &vreg->parts->freq, i + 1); + return 0; + } + } + + dev_err(dev, "invalid frequency %d\n", freq); + return -EINVAL; +} + +static int rpm_reg_probe(struct platform_device *pdev) +{ + struct regulator_init_data *initdata; + const struct qcom_rpm_reg *template; + const struct of_device_id *match; + struct regulator_config config = { }; + struct regulator_dev *rdev; + struct qcom_rpm_reg *vreg; + const char *key; + u32 force_mode; + bool pwm; + u32 val; + int ret; + + match = of_match_device(rpm_of_match, &pdev->dev); + template = match->data; + + initdata = of_get_regulator_init_data(&pdev->dev, pdev->dev.of_node); + if (!initdata) + return -EINVAL; + + vreg = devm_kmalloc(&pdev->dev, sizeof(*vreg), GFP_KERNEL); + if (!vreg) { + dev_err(&pdev->dev, "failed to allocate vreg\n"); + return -ENOMEM; + } + memcpy(vreg, template, sizeof(*vreg)); + mutex_init(&vreg->lock); + vreg->dev = &pdev->dev; + vreg->desc.id = -1; + vreg->desc.owner = THIS_MODULE; + vreg->desc.type = REGULATOR_VOLTAGE; + vreg->desc.name = pdev->dev.of_node->name; + + vreg->rpm = dev_get_drvdata(pdev->dev.parent); + if (!vreg->rpm) { + dev_err(&pdev->dev, "unable to retrieve handle to rpm\n"); + return -ENODEV; + } + + key = "reg"; + ret = of_property_read_u32(pdev->dev.of_node, key, &val); + if (ret) { + dev_err(&pdev->dev, "failed to read %s\n", key); + return ret; + } + vreg->resource = val; + + if ((vreg->parts->uV.mask || vreg->parts->mV.mask) && + (!initdata->constraints.min_uV || !initdata->constraints.max_uV)) { + dev_err(&pdev->dev, "no voltage specified for regulator\n"); + return -EINVAL; + } + + key = "bias-pull-down"; + if (of_property_read_bool(pdev->dev.of_node, key)) { + ret = rpm_reg_set(vreg, &vreg->parts->pd, 1); + if (ret) { + dev_err(&pdev->dev, "%s is invalid", key); + return ret; + } + } + + if (vreg->parts->freq.mask) { + ret = rpm_reg_of_parse_freq(&pdev->dev, vreg); + if (ret < 0) + return ret; + } + + if (vreg->parts->pm.mask) { + key = "qcom,power-mode-hysteretic"; + pwm = !of_property_read_bool(pdev->dev.of_node, key); + + ret = rpm_reg_set(vreg, &vreg->parts->pm, pwm); + if (ret) { + dev_err(&pdev->dev, "failed to set power mode\n"); + return ret; + } + } + + if (vreg->parts->fm.mask) { + force_mode = -1; + + key = "qcom,force-mode"; + ret = of_property_read_u32(pdev->dev.of_node, key, &val); + if (ret == -EINVAL) { + val = QCOM_RPM_FORCE_MODE_NONE; + } else if (ret < 0) { + dev_err(&pdev->dev, "failed to read %s\n", key); + return ret; + } + + /* + * If force-mode is encoded as 2 bits then the + * possible register values are: + * NONE, LPM, HPM + * otherwise: + * NONE, LPM, AUTO, HPM, BYPASS + */ + switch (val) { + case QCOM_RPM_FORCE_MODE_NONE: + force_mode = 0; + break; + case QCOM_RPM_FORCE_MODE_LPM: + force_mode = 1; + break; + case QCOM_RPM_FORCE_MODE_HPM: + if (FORCE_MODE_IS_2_BITS(vreg)) + force_mode = 2; + else + force_mode = 3; + break; + case QCOM_RPM_FORCE_MODE_AUTO: + if (vreg->supports_force_mode_auto) + force_mode = 2; + break; + case QCOM_RPM_FORCE_MODE_BYPASS: + if (vreg->supports_force_mode_bypass) + force_mode = 4; + break; + } + + if (force_mode < 0) { + dev_err(&pdev->dev, "invalid force mode\n"); + return -EINVAL; + } + + ret = rpm_reg_set(vreg, &vreg->parts->fm, force_mode); + if (ret) { + dev_err(&pdev->dev, "failed to set force mode\n"); + return ret; + } + } + + config.dev = &pdev->dev; + config.init_data = initdata; + config.driver_data = vreg; + config.of_node = pdev->dev.of_node; + rdev = devm_regulator_register(&pdev->dev, &vreg->desc, &config); + if (IS_ERR(rdev)) { + dev_err(&pdev->dev, "can't register regulator\n"); + return PTR_ERR(rdev); + } + + return 0; +} + +static struct platform_driver rpm_reg_driver = { + .probe = rpm_reg_probe, + .driver = { + .name = "qcom_rpm_reg", + .owner = THIS_MODULE, + .of_match_table = of_match_ptr(rpm_of_match), + }, +}; + +static int __init rpm_reg_init(void) +{ + return platform_driver_register(&rpm_reg_driver); +} +subsys_initcall(rpm_reg_init); + +static void __exit rpm_reg_exit(void) +{ + platform_driver_unregister(&rpm_reg_driver); +} +module_exit(rpm_reg_exit) + +MODULE_DESCRIPTION("Qualcomm RPM regulator driver"); +MODULE_LICENSE("GPL v2"); diff --git a/drivers/regulator/rk808-regulator.c b/drivers/regulator/rk808-regulator.c new file mode 100644 index 0000000..e305416 --- /dev/null +++ b/drivers/regulator/rk808-regulator.c @@ -0,0 +1,381 @@ +/* + * Regulator driver for Rockchip RK808 + * + * Copyright (c) 2014, Fuzhou Rockchip Electronics Co., Ltd + * + * Author: Chris Zhong <zyw@rock-chips.com> + * Author: Zhang Qing <zhangqing@rock-chips.com> + * + * This program is free software; you can redistribute it and/or modify it + * under the terms and conditions of the GNU General Public License, + * version 2, as published by the Free Software Foundation. + * + * This program is distributed in the hope it will be useful, but WITHOUT + * ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or + * FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for + * more details. + */ + +#include <linux/module.h> +#include <linux/i2c.h> +#include <linux/mfd/rk808.h> +#include <linux/of_device.h> +#include <linux/regulator/driver.h> +#include <linux/regulator/of_regulator.h> + +/* Field Definitions */ +#define RK808_BUCK_VSEL_MASK 0x3f +#define RK808_BUCK4_VSEL_MASK 0xf +#define RK808_LDO_VSEL_MASK 0x1f + +/* Ramp rate definitions for buck1 / buck2 only */ +#define RK808_RAMP_RATE_OFFSET 3 +#define RK808_RAMP_RATE_MASK (3 << RK808_RAMP_RATE_OFFSET) +#define RK808_RAMP_RATE_2MV_PER_US (0 << RK808_RAMP_RATE_OFFSET) +#define RK808_RAMP_RATE_4MV_PER_US (1 << RK808_RAMP_RATE_OFFSET) +#define RK808_RAMP_RATE_6MV_PER_US (2 << RK808_RAMP_RATE_OFFSET) +#define RK808_RAMP_RATE_10MV_PER_US (3 << RK808_RAMP_RATE_OFFSET) + +static const int rk808_buck_config_regs[] = { + RK808_BUCK1_CONFIG_REG, + RK808_BUCK2_CONFIG_REG, + RK808_BUCK3_CONFIG_REG, + RK808_BUCK4_CONFIG_REG, +}; + +static const struct regulator_linear_range rk808_buck_voltage_ranges[] = { + REGULATOR_LINEAR_RANGE(700000, 0, 63, 12500), +}; + +static const struct regulator_linear_range rk808_buck4_voltage_ranges[] = { + REGULATOR_LINEAR_RANGE(1800000, 0, 15, 100000), +}; + +static const struct regulator_linear_range rk808_ldo_voltage_ranges[] = { + REGULATOR_LINEAR_RANGE(1800000, 0, 16, 100000), +}; + +static const struct regulator_linear_range rk808_ldo3_voltage_ranges[] = { + REGULATOR_LINEAR_RANGE(800000, 0, 13, 100000), + REGULATOR_LINEAR_RANGE(2500000, 15, 15, 0), +}; + +static const struct regulator_linear_range rk808_ldo6_voltage_ranges[] = { + REGULATOR_LINEAR_RANGE(800000, 0, 17, 100000), +}; + +static int rk808_set_ramp_delay(struct regulator_dev *rdev, int ramp_delay) +{ + unsigned int ramp_value = RK808_RAMP_RATE_10MV_PER_US; + unsigned int reg = rk808_buck_config_regs[rdev->desc->id - + RK808_ID_DCDC1]; + + switch (ramp_delay) { + case 1 ... 2000: + ramp_value = RK808_RAMP_RATE_2MV_PER_US; + break; + case 2001 ... 4000: + ramp_value = RK808_RAMP_RATE_4MV_PER_US; + break; + case 4001 ... 6000: + ramp_value = RK808_RAMP_RATE_6MV_PER_US; + break; + case 6001 ... 10000: + break; + default: + pr_warn("%s ramp_delay: %d not supported, setting 10000\n", + rdev->desc->name, ramp_delay); + } + + return regmap_update_bits(rdev->regmap, reg, + RK808_RAMP_RATE_MASK, ramp_value); +} + +static struct regulator_ops rk808_buck1_2_ops = { + .list_voltage = regulator_list_voltage_linear_range, + .map_voltage = regulator_map_voltage_linear_range, + .get_voltage_sel = regulator_get_voltage_sel_regmap, + .set_voltage_sel = regulator_set_voltage_sel_regmap, + .enable = regulator_enable_regmap, + .disable = regulator_disable_regmap, + .is_enabled = regulator_is_enabled_regmap, + .set_ramp_delay = rk808_set_ramp_delay, +}; + +static struct regulator_ops rk808_reg_ops = { + .list_voltage = regulator_list_voltage_linear_range, + .map_voltage = regulator_map_voltage_linear_range, + .get_voltage_sel = regulator_get_voltage_sel_regmap, + .set_voltage_sel = regulator_set_voltage_sel_regmap, + .enable = regulator_enable_regmap, + .disable = regulator_disable_regmap, + .is_enabled = regulator_is_enabled_regmap, +}; + +static struct regulator_ops rk808_switch_ops = { + .enable = regulator_enable_regmap, + .disable = regulator_disable_regmap, + .is_enabled = regulator_is_enabled_regmap, +}; + +static const struct regulator_desc rk808_reg[] = { + { + .name = "DCDC_REG1", + .supply_name = "vcc1", + .id = RK808_ID_DCDC1, + .ops = &rk808_buck1_2_ops, + .type = REGULATOR_VOLTAGE, + .n_voltages = 64, + .linear_ranges = rk808_buck_voltage_ranges, + .n_linear_ranges = ARRAY_SIZE(rk808_buck_voltage_ranges), + .vsel_reg = RK808_BUCK1_ON_VSEL_REG, + .vsel_mask = RK808_BUCK_VSEL_MASK, + .enable_reg = RK808_DCDC_EN_REG, + .enable_mask = BIT(0), + .owner = THIS_MODULE, + }, { + .name = "DCDC_REG2", + .supply_name = "vcc2", + .id = RK808_ID_DCDC2, + .ops = &rk808_buck1_2_ops, + .type = REGULATOR_VOLTAGE, + .n_voltages = 64, + .linear_ranges = rk808_buck_voltage_ranges, + .n_linear_ranges = ARRAY_SIZE(rk808_buck_voltage_ranges), + .vsel_reg = RK808_BUCK2_ON_VSEL_REG, + .vsel_mask = RK808_BUCK_VSEL_MASK, + .enable_reg = RK808_DCDC_EN_REG, + .enable_mask = BIT(1), + .owner = THIS_MODULE, + }, { + .name = "DCDC_REG3", + .supply_name = "vcc3", + .id = RK808_ID_DCDC3, + .ops = &rk808_switch_ops, + .type = REGULATOR_VOLTAGE, + .n_voltages = 1, + .enable_reg = RK808_DCDC_EN_REG, + .enable_mask = BIT(2), + .owner = THIS_MODULE, + }, { + .name = "DCDC_REG4", + .supply_name = "vcc4", + .id = RK808_ID_DCDC4, + .ops = &rk808_reg_ops, + .type = REGULATOR_VOLTAGE, + .n_voltages = 16, + .linear_ranges = rk808_buck4_voltage_ranges, + .n_linear_ranges = ARRAY_SIZE(rk808_buck4_voltage_ranges), + .vsel_reg = RK808_BUCK4_ON_VSEL_REG, + .vsel_mask = RK808_BUCK4_VSEL_MASK, + .enable_reg = RK808_DCDC_EN_REG, + .enable_mask = BIT(3), + .owner = THIS_MODULE, + }, { + .name = "LDO_REG1", + .supply_name = "vcc6", + .id = RK808_ID_LDO1, + .ops = &rk808_reg_ops, + .type = REGULATOR_VOLTAGE, + .n_voltages = 17, + .linear_ranges = rk808_ldo_voltage_ranges, + .n_linear_ranges = ARRAY_SIZE(rk808_ldo_voltage_ranges), + .vsel_reg = RK808_LDO1_ON_VSEL_REG, + .vsel_mask = RK808_LDO_VSEL_MASK, + .enable_reg = RK808_LDO_EN_REG, + .enable_mask = BIT(0), + .owner = THIS_MODULE, + }, { + .name = "LDO_REG2", + .supply_name = "vcc6", + .id = RK808_ID_LDO2, + .ops = &rk808_reg_ops, + .type = REGULATOR_VOLTAGE, + .n_voltages = 17, + .linear_ranges = rk808_ldo_voltage_ranges, + .n_linear_ranges = ARRAY_SIZE(rk808_ldo_voltage_ranges), + .vsel_reg = RK808_LDO2_ON_VSEL_REG, + .vsel_mask = RK808_LDO_VSEL_MASK, + .enable_reg = RK808_LDO_EN_REG, + .enable_mask = BIT(1), + .owner = THIS_MODULE, + }, { + .name = "LDO_REG3", + .supply_name = "vcc7", + .id = RK808_ID_LDO3, + .ops = &rk808_reg_ops, + .type = REGULATOR_VOLTAGE, + .n_voltages = 16, + .linear_ranges = rk808_ldo3_voltage_ranges, + .n_linear_ranges = ARRAY_SIZE(rk808_ldo3_voltage_ranges), + .vsel_reg = RK808_LDO3_ON_VSEL_REG, + .vsel_mask = RK808_BUCK4_VSEL_MASK, + .enable_reg = RK808_LDO_EN_REG, + .enable_mask = BIT(2), + .owner = THIS_MODULE, + }, { + .name = "LDO_REG4", + .supply_name = "vcc9", + .id = RK808_ID_LDO4, + .ops = &rk808_reg_ops, + .type = REGULATOR_VOLTAGE, + .n_voltages = 17, + .linear_ranges = rk808_ldo_voltage_ranges, + .n_linear_ranges = ARRAY_SIZE(rk808_ldo_voltage_ranges), + .vsel_reg = RK808_LDO4_ON_VSEL_REG, + .vsel_mask = RK808_LDO_VSEL_MASK, + .enable_reg = RK808_LDO_EN_REG, + .enable_mask = BIT(3), + .owner = THIS_MODULE, + }, { + .name = "LDO_REG5", + .supply_name = "vcc9", + .id = RK808_ID_LDO5, + .ops = &rk808_reg_ops, + .type = REGULATOR_VOLTAGE, + .n_voltages = 17, + .linear_ranges = rk808_ldo_voltage_ranges, + .n_linear_ranges = ARRAY_SIZE(rk808_ldo_voltage_ranges), + .vsel_reg = RK808_LDO5_ON_VSEL_REG, + .vsel_mask = RK808_LDO_VSEL_MASK, + .enable_reg = RK808_LDO_EN_REG, + .enable_mask = BIT(4), + .owner = THIS_MODULE, + }, { + .name = "LDO_REG6", + .supply_name = "vcc10", + .id = RK808_ID_LDO6, + .ops = &rk808_reg_ops, + .type = REGULATOR_VOLTAGE, + .n_voltages = 18, + .linear_ranges = rk808_ldo6_voltage_ranges, + .n_linear_ranges = ARRAY_SIZE(rk808_ldo6_voltage_ranges), + .vsel_reg = RK808_LDO6_ON_VSEL_REG, + .vsel_mask = RK808_LDO_VSEL_MASK, + .enable_reg = RK808_LDO_EN_REG, + .enable_mask = BIT(5), + .owner = THIS_MODULE, + }, { + .name = "LDO_REG7", + .supply_name = "vcc7", + .id = RK808_ID_LDO7, + .ops = &rk808_reg_ops, + .type = REGULATOR_VOLTAGE, + .n_voltages = 18, + .linear_ranges = rk808_ldo6_voltage_ranges, + .n_linear_ranges = ARRAY_SIZE(rk808_ldo6_voltage_ranges), + .vsel_reg = RK808_LDO7_ON_VSEL_REG, + .vsel_mask = RK808_LDO_VSEL_MASK, + .enable_reg = RK808_LDO_EN_REG, + .enable_mask = BIT(6), + .owner = THIS_MODULE, + }, { + .name = "LDO_REG8", + .supply_name = "vcc11", + .id = RK808_ID_LDO8, + .ops = &rk808_reg_ops, + .type = REGULATOR_VOLTAGE, + .n_voltages = 17, + .linear_ranges = rk808_ldo_voltage_ranges, + .n_linear_ranges = ARRAY_SIZE(rk808_ldo_voltage_ranges), + .vsel_reg = RK808_LDO8_ON_VSEL_REG, + .vsel_mask = RK808_LDO_VSEL_MASK, + .enable_reg = RK808_LDO_EN_REG, + .enable_mask = BIT(7), + .owner = THIS_MODULE, + }, { + .name = "SWITCH_REG1", + .supply_name = "vcc8", + .id = RK808_ID_SWITCH1, + .ops = &rk808_switch_ops, + .type = REGULATOR_VOLTAGE, + .enable_reg = RK808_DCDC_EN_REG, + .enable_mask = BIT(5), + .owner = THIS_MODULE, + }, { + .name = "SWITCH_REG2", + .supply_name = "vcc12", + .id = RK808_ID_SWITCH2, + .ops = &rk808_switch_ops, + .type = REGULATOR_VOLTAGE, + .enable_reg = RK808_DCDC_EN_REG, + .enable_mask = BIT(6), + .owner = THIS_MODULE, + }, +}; + +static struct of_regulator_match rk808_reg_matches[] = { + [RK808_ID_DCDC1] = { .name = "DCDC_REG1" }, + [RK808_ID_DCDC2] = { .name = "DCDC_REG2" }, + [RK808_ID_DCDC3] = { .name = "DCDC_REG3" }, + [RK808_ID_DCDC4] = { .name = "DCDC_REG4" }, + [RK808_ID_LDO1] = { .name = "LDO_REG1" }, + [RK808_ID_LDO2] = { .name = "LDO_REG2" }, + [RK808_ID_LDO3] = { .name = "LDO_REG3" }, + [RK808_ID_LDO4] = { .name = "LDO_REG4" }, + [RK808_ID_LDO5] = { .name = "LDO_REG5" }, + [RK808_ID_LDO6] = { .name = "LDO_REG6" }, + [RK808_ID_LDO7] = { .name = "LDO_REG7" }, + [RK808_ID_LDO8] = { .name = "LDO_REG8" }, + [RK808_ID_SWITCH1] = { .name = "SWITCH_REG1" }, + [RK808_ID_SWITCH2] = { .name = "SWITCH_REG2" }, +}; + +static int rk808_regulator_probe(struct platform_device *pdev) +{ + struct rk808 *rk808 = dev_get_drvdata(pdev->dev.parent); + struct i2c_client *client = rk808->i2c; + struct device_node *reg_np; + struct regulator_config config = {}; + struct regulator_dev *rk808_rdev; + int ret, i; + + reg_np = of_get_child_by_name(client->dev.of_node, "regulators"); + if (!reg_np) + return -ENXIO; + + ret = of_regulator_match(&pdev->dev, reg_np, rk808_reg_matches, + RK808_NUM_REGULATORS); + of_node_put(reg_np); + if (ret < 0) + return ret; + + /* Instantiate the regulators */ + for (i = 0; i < RK808_NUM_REGULATORS; i++) { + if (!rk808_reg_matches[i].init_data || + !rk808_reg_matches[i].of_node) + continue; + + config.dev = &client->dev; + config.driver_data = rk808; + config.regmap = rk808->regmap; + config.of_node = rk808_reg_matches[i].of_node; + config.init_data = rk808_reg_matches[i].init_data; + + rk808_rdev = devm_regulator_register(&pdev->dev, + &rk808_reg[i], &config); + if (IS_ERR(rk808_rdev)) { + dev_err(&client->dev, + "failed to register %d regulator\n", i); + return PTR_ERR(rk808_rdev); + } + } + + return 0; +} + +static struct platform_driver rk808_regulator_driver = { + .probe = rk808_regulator_probe, + .driver = { + .name = "rk808-regulator", + .owner = THIS_MODULE, + }, +}; + +module_platform_driver(rk808_regulator_driver); + +MODULE_DESCRIPTION("regulator driver for the rk808 series PMICs"); +MODULE_AUTHOR("Chris Zhong<zyw@rock-chips.com>"); +MODULE_AUTHOR("Zhang Qing<zhangqing@rock-chips.com>"); +MODULE_LICENSE("GPL"); +MODULE_ALIAS("platform:rk808-regulator"); diff --git a/drivers/regulator/rn5t618-regulator.c b/drivers/regulator/rn5t618-regulator.c new file mode 100644 index 0000000..e58d79a --- /dev/null +++ b/drivers/regulator/rn5t618-regulator.c @@ -0,0 +1,143 @@ +/* + * Regulator driver for Ricoh RN5T618 PMIC + * + * Copyright (C) 2014 Beniamino Galvani <b.galvani@gmail.com> + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License + * version 2 as published by the Free Software Foundation. + * + * You should have received a copy of the GNU General Public License + * along with this program. If not, see <http://www.gnu.org/licenses/>. + */ + +#include <linux/mfd/rn5t618.h> +#include <linux/module.h> +#include <linux/of.h> +#include <linux/platform_device.h> +#include <linux/regmap.h> +#include <linux/regulator/driver.h> +#include <linux/regulator/of_regulator.h> + +static struct regulator_ops rn5t618_reg_ops = { + .enable = regulator_enable_regmap, + .disable = regulator_disable_regmap, + .is_enabled = regulator_is_enabled_regmap, + .set_voltage_sel = regulator_set_voltage_sel_regmap, + .get_voltage_sel = regulator_get_voltage_sel_regmap, + .list_voltage = regulator_list_voltage_linear, +}; + +#define REG(rid, ereg, emask, vreg, vmask, min, max, step) \ + [RN5T618_##rid] = { \ + .name = #rid, \ + .id = RN5T618_##rid, \ + .type = REGULATOR_VOLTAGE, \ + .owner = THIS_MODULE, \ + .ops = &rn5t618_reg_ops, \ + .n_voltages = ((max) - (min)) / (step) + 1, \ + .min_uV = (min), \ + .uV_step = (step), \ + .enable_reg = RN5T618_##ereg, \ + .enable_mask = (emask), \ + .vsel_reg = RN5T618_##vreg, \ + .vsel_mask = (vmask), \ + } + +static struct regulator_desc rn5t618_regulators[] = { + /* DCDC */ + REG(DCDC1, DC1CTL, BIT(0), DC1DAC, 0xff, 600000, 3500000, 12500), + REG(DCDC2, DC2CTL, BIT(0), DC2DAC, 0xff, 600000, 3500000, 12500), + REG(DCDC3, DC3CTL, BIT(0), DC3DAC, 0xff, 600000, 3500000, 12500), + /* LDO */ + REG(LDO1, LDOEN1, BIT(0), LDO1DAC, 0x7f, 900000, 3500000, 25000), + REG(LDO2, LDOEN1, BIT(1), LDO2DAC, 0x7f, 900000, 3500000, 25000), + REG(LDO3, LDOEN1, BIT(2), LDO3DAC, 0x7f, 600000, 3500000, 25000), + REG(LDO4, LDOEN1, BIT(3), LDO4DAC, 0x7f, 900000, 3500000, 25000), + REG(LDO5, LDOEN1, BIT(4), LDO5DAC, 0x7f, 900000, 3500000, 25000), + /* LDO RTC */ + REG(LDORTC1, LDOEN2, BIT(4), LDORTCDAC, 0x7f, 1700000, 3500000, 25000), + REG(LDORTC2, LDOEN2, BIT(5), LDORTC2DAC, 0x7f, 900000, 3500000, 25000), +}; + +static struct of_regulator_match rn5t618_matches[] = { + [RN5T618_DCDC1] = { .name = "DCDC1" }, + [RN5T618_DCDC2] = { .name = "DCDC2" }, + [RN5T618_DCDC3] = { .name = "DCDC3" }, + [RN5T618_LDO1] = { .name = "LDO1" }, + [RN5T618_LDO2] = { .name = "LDO2" }, + [RN5T618_LDO3] = { .name = "LDO3" }, + [RN5T618_LDO4] = { .name = "LDO4" }, + [RN5T618_LDO5] = { .name = "LDO5" }, + [RN5T618_LDORTC1] = { .name = "LDORTC1" }, + [RN5T618_LDORTC2] = { .name = "LDORTC2" }, +}; + +static int rn5t618_regulator_parse_dt(struct platform_device *pdev) +{ + struct device_node *np, *regulators; + int ret; + + np = of_node_get(pdev->dev.parent->of_node); + if (!np) + return 0; + + regulators = of_get_child_by_name(np, "regulators"); + if (!regulators) { + dev_err(&pdev->dev, "regulators node not found\n"); + return -EINVAL; + } + + ret = of_regulator_match(&pdev->dev, regulators, rn5t618_matches, + ARRAY_SIZE(rn5t618_matches)); + of_node_put(regulators); + if (ret < 0) { + dev_err(&pdev->dev, "error parsing regulator init data: %d\n", + ret); + } + + return 0; +} + +static int rn5t618_regulator_probe(struct platform_device *pdev) +{ + struct rn5t618 *rn5t618 = dev_get_drvdata(pdev->dev.parent); + struct regulator_config config = { }; + struct regulator_dev *rdev; + int ret, i; + + ret = rn5t618_regulator_parse_dt(pdev); + if (ret) + return ret; + + for (i = 0; i < RN5T618_REG_NUM; i++) { + config.dev = &pdev->dev; + config.init_data = rn5t618_matches[i].init_data; + config.of_node = rn5t618_matches[i].of_node; + config.regmap = rn5t618->regmap; + + rdev = devm_regulator_register(&pdev->dev, + &rn5t618_regulators[i], + &config); + if (IS_ERR(rdev)) { + dev_err(&pdev->dev, "failed to register %s regulator\n", + rn5t618_regulators[i].name); + return PTR_ERR(rdev); + } + } + + return 0; +} + +static struct platform_driver rn5t618_regulator_driver = { + .probe = rn5t618_regulator_probe, + .driver = { + .name = "rn5t618-regulator", + }, +}; + +module_platform_driver(rn5t618_regulator_driver); + +MODULE_AUTHOR("Beniamino Galvani <b.galvani@gmail.com>"); +MODULE_DESCRIPTION("RN5T618 regulator driver"); +MODULE_LICENSE("GPL v2"); diff --git a/drivers/regulator/s2mpa01.c b/drivers/regulator/s2mpa01.c index ee83b48..4acefa6 100644 --- a/drivers/regulator/s2mpa01.c +++ b/drivers/regulator/s2mpa01.c @@ -235,28 +235,14 @@ static struct regulator_ops s2mpa01_buck_ops = { .set_ramp_delay = s2mpa01_set_ramp_delay, }; -#define regulator_desc_ldo1(num) { \ +#define regulator_desc_ldo(num, step) { \ .name = "LDO"#num, \ .id = S2MPA01_LDO##num, \ .ops = &s2mpa01_ldo_ops, \ .type = REGULATOR_VOLTAGE, \ .owner = THIS_MODULE, \ - .min_uV = S2MPA01_LDO_MIN, \ - .uV_step = S2MPA01_LDO_STEP1, \ - .n_voltages = S2MPA01_LDO_N_VOLTAGES, \ - .vsel_reg = S2MPA01_REG_L1CTRL + num - 1, \ - .vsel_mask = S2MPA01_LDO_VSEL_MASK, \ - .enable_reg = S2MPA01_REG_L1CTRL + num - 1, \ - .enable_mask = S2MPA01_ENABLE_MASK \ -} -#define regulator_desc_ldo2(num) { \ - .name = "LDO"#num, \ - .id = S2MPA01_LDO##num, \ - .ops = &s2mpa01_ldo_ops, \ - .type = REGULATOR_VOLTAGE, \ - .owner = THIS_MODULE, \ - .min_uV = S2MPA01_LDO_MIN, \ - .uV_step = S2MPA01_LDO_STEP2, \ + .min_uV = MIN_800_MV, \ + .uV_step = step, \ .n_voltages = S2MPA01_LDO_N_VOLTAGES, \ .vsel_reg = S2MPA01_REG_L1CTRL + num - 1, \ .vsel_mask = S2MPA01_LDO_VSEL_MASK, \ @@ -270,8 +256,8 @@ static struct regulator_ops s2mpa01_buck_ops = { .ops = &s2mpa01_buck_ops, \ .type = REGULATOR_VOLTAGE, \ .owner = THIS_MODULE, \ - .min_uV = S2MPA01_BUCK_MIN1, \ - .uV_step = S2MPA01_BUCK_STEP1, \ + .min_uV = MIN_600_MV, \ + .uV_step = STEP_6_25_MV, \ .n_voltages = S2MPA01_BUCK_N_VOLTAGES, \ .ramp_delay = S2MPA01_RAMP_DELAY, \ .vsel_reg = S2MPA01_REG_B1CTRL2 + (num - 1) * 2, \ @@ -286,8 +272,8 @@ static struct regulator_ops s2mpa01_buck_ops = { .ops = &s2mpa01_buck_ops, \ .type = REGULATOR_VOLTAGE, \ .owner = THIS_MODULE, \ - .min_uV = S2MPA01_BUCK_MIN2, \ - .uV_step = S2MPA01_BUCK_STEP1, \ + .min_uV = MIN_800_MV, \ + .uV_step = STEP_6_25_MV, \ .n_voltages = S2MPA01_BUCK_N_VOLTAGES, \ .ramp_delay = S2MPA01_RAMP_DELAY, \ .vsel_reg = S2MPA01_REG_B5CTRL2, \ @@ -296,14 +282,14 @@ static struct regulator_ops s2mpa01_buck_ops = { .enable_mask = S2MPA01_ENABLE_MASK \ } -#define regulator_desc_buck6_7(num) { \ +#define regulator_desc_buck6_10(num, min, step) { \ .name = "BUCK"#num, \ .id = S2MPA01_BUCK##num, \ .ops = &s2mpa01_buck_ops, \ .type = REGULATOR_VOLTAGE, \ .owner = THIS_MODULE, \ - .min_uV = S2MPA01_BUCK_MIN1, \ - .uV_step = S2MPA01_BUCK_STEP1, \ + .min_uV = min, \ + .uV_step = step, \ .n_voltages = S2MPA01_BUCK_N_VOLTAGES, \ .ramp_delay = S2MPA01_RAMP_DELAY, \ .vsel_reg = S2MPA01_REG_B6CTRL2 + (num - 6) * 2, \ @@ -312,91 +298,43 @@ static struct regulator_ops s2mpa01_buck_ops = { .enable_mask = S2MPA01_ENABLE_MASK \ } -#define regulator_desc_buck8 { \ - .name = "BUCK8", \ - .id = S2MPA01_BUCK8, \ - .ops = &s2mpa01_buck_ops, \ - .type = REGULATOR_VOLTAGE, \ - .owner = THIS_MODULE, \ - .min_uV = S2MPA01_BUCK_MIN2, \ - .uV_step = S2MPA01_BUCK_STEP2, \ - .n_voltages = S2MPA01_BUCK_N_VOLTAGES, \ - .ramp_delay = S2MPA01_RAMP_DELAY, \ - .vsel_reg = S2MPA01_REG_B8CTRL2, \ - .vsel_mask = S2MPA01_BUCK_VSEL_MASK, \ - .enable_reg = S2MPA01_REG_B8CTRL1, \ - .enable_mask = S2MPA01_ENABLE_MASK \ -} - -#define regulator_desc_buck9 { \ - .name = "BUCK9", \ - .id = S2MPA01_BUCK9, \ - .ops = &s2mpa01_buck_ops, \ - .type = REGULATOR_VOLTAGE, \ - .owner = THIS_MODULE, \ - .min_uV = S2MPA01_BUCK_MIN4, \ - .uV_step = S2MPA01_BUCK_STEP2, \ - .n_voltages = S2MPA01_BUCK_N_VOLTAGES, \ - .ramp_delay = S2MPA01_RAMP_DELAY, \ - .vsel_reg = S2MPA01_REG_B9CTRL2, \ - .vsel_mask = S2MPA01_BUCK_VSEL_MASK, \ - .enable_reg = S2MPA01_REG_B9CTRL1, \ - .enable_mask = S2MPA01_ENABLE_MASK \ -} - -#define regulator_desc_buck10 { \ - .name = "BUCK10", \ - .id = S2MPA01_BUCK10, \ - .ops = &s2mpa01_buck_ops, \ - .type = REGULATOR_VOLTAGE, \ - .owner = THIS_MODULE, \ - .min_uV = S2MPA01_BUCK_MIN3, \ - .uV_step = S2MPA01_BUCK_STEP2, \ - .n_voltages = S2MPA01_BUCK_N_VOLTAGES, \ - .ramp_delay = S2MPA01_RAMP_DELAY, \ - .vsel_reg = S2MPA01_REG_B10CTRL2, \ - .vsel_mask = S2MPA01_BUCK_VSEL_MASK, \ - .enable_reg = S2MPA01_REG_B10CTRL1, \ - .enable_mask = S2MPA01_ENABLE_MASK \ -} - static struct regulator_desc regulators[] = { - regulator_desc_ldo2(1), - regulator_desc_ldo1(2), - regulator_desc_ldo1(3), - regulator_desc_ldo1(4), - regulator_desc_ldo1(5), - regulator_desc_ldo2(6), - regulator_desc_ldo1(7), - regulator_desc_ldo1(8), - regulator_desc_ldo1(9), - regulator_desc_ldo1(10), - regulator_desc_ldo2(11), - regulator_desc_ldo1(12), - regulator_desc_ldo1(13), - regulator_desc_ldo1(14), - regulator_desc_ldo1(15), - regulator_desc_ldo1(16), - regulator_desc_ldo1(17), - regulator_desc_ldo1(18), - regulator_desc_ldo1(19), - regulator_desc_ldo1(20), - regulator_desc_ldo1(21), - regulator_desc_ldo2(22), - regulator_desc_ldo2(23), - regulator_desc_ldo1(24), - regulator_desc_ldo1(25), - regulator_desc_ldo1(26), + regulator_desc_ldo(1, STEP_25_MV), + regulator_desc_ldo(2, STEP_50_MV), + regulator_desc_ldo(3, STEP_50_MV), + regulator_desc_ldo(4, STEP_50_MV), + regulator_desc_ldo(5, STEP_50_MV), + regulator_desc_ldo(6, STEP_25_MV), + regulator_desc_ldo(7, STEP_50_MV), + regulator_desc_ldo(8, STEP_50_MV), + regulator_desc_ldo(9, STEP_50_MV), + regulator_desc_ldo(10, STEP_50_MV), + regulator_desc_ldo(11, STEP_25_MV), + regulator_desc_ldo(12, STEP_50_MV), + regulator_desc_ldo(13, STEP_50_MV), + regulator_desc_ldo(14, STEP_50_MV), + regulator_desc_ldo(15, STEP_50_MV), + regulator_desc_ldo(16, STEP_50_MV), + regulator_desc_ldo(17, STEP_50_MV), + regulator_desc_ldo(18, STEP_50_MV), + regulator_desc_ldo(19, STEP_50_MV), + regulator_desc_ldo(20, STEP_50_MV), + regulator_desc_ldo(21, STEP_50_MV), + regulator_desc_ldo(22, STEP_25_MV), + regulator_desc_ldo(23, STEP_25_MV), + regulator_desc_ldo(24, STEP_50_MV), + regulator_desc_ldo(25, STEP_50_MV), + regulator_desc_ldo(26, STEP_50_MV), regulator_desc_buck1_4(1), regulator_desc_buck1_4(2), regulator_desc_buck1_4(3), regulator_desc_buck1_4(4), regulator_desc_buck5, - regulator_desc_buck6_7(6), - regulator_desc_buck6_7(7), - regulator_desc_buck8, - regulator_desc_buck9, - regulator_desc_buck10, + regulator_desc_buck6_10(6, MIN_600_MV, STEP_6_25_MV), + regulator_desc_buck6_10(7, MIN_600_MV, STEP_6_25_MV), + regulator_desc_buck6_10(8, MIN_800_MV, STEP_12_5_MV), + regulator_desc_buck6_10(9, MIN_1500_MV, STEP_12_5_MV), + regulator_desc_buck6_10(10, MIN_1000_MV, STEP_12_5_MV), }; static int s2mpa01_pmic_probe(struct platform_device *pdev) diff --git a/drivers/regulator/s2mps11.c b/drivers/regulator/s2mps11.c index b16c53a..adab82d 100644 --- a/drivers/regulator/s2mps11.c +++ b/drivers/regulator/s2mps11.c @@ -255,28 +255,14 @@ static struct regulator_ops s2mps11_buck_ops = { .set_ramp_delay = s2mps11_set_ramp_delay, }; -#define regulator_desc_s2mps11_ldo1(num) { \ +#define regulator_desc_s2mps11_ldo(num, step) { \ .name = "LDO"#num, \ .id = S2MPS11_LDO##num, \ .ops = &s2mps11_ldo_ops, \ .type = REGULATOR_VOLTAGE, \ .owner = THIS_MODULE, \ - .min_uV = S2MPS11_LDO_MIN, \ - .uV_step = S2MPS11_LDO_STEP1, \ - .n_voltages = S2MPS11_LDO_N_VOLTAGES, \ - .vsel_reg = S2MPS11_REG_L1CTRL + num - 1, \ - .vsel_mask = S2MPS11_LDO_VSEL_MASK, \ - .enable_reg = S2MPS11_REG_L1CTRL + num - 1, \ - .enable_mask = S2MPS11_ENABLE_MASK \ -} -#define regulator_desc_s2mps11_ldo2(num) { \ - .name = "LDO"#num, \ - .id = S2MPS11_LDO##num, \ - .ops = &s2mps11_ldo_ops, \ - .type = REGULATOR_VOLTAGE, \ - .owner = THIS_MODULE, \ - .min_uV = S2MPS11_LDO_MIN, \ - .uV_step = S2MPS11_LDO_STEP2, \ + .min_uV = MIN_800_MV, \ + .uV_step = step, \ .n_voltages = S2MPS11_LDO_N_VOLTAGES, \ .vsel_reg = S2MPS11_REG_L1CTRL + num - 1, \ .vsel_mask = S2MPS11_LDO_VSEL_MASK, \ @@ -290,8 +276,8 @@ static struct regulator_ops s2mps11_buck_ops = { .ops = &s2mps11_buck_ops, \ .type = REGULATOR_VOLTAGE, \ .owner = THIS_MODULE, \ - .min_uV = S2MPS11_BUCK_MIN1, \ - .uV_step = S2MPS11_BUCK_STEP1, \ + .min_uV = MIN_600_MV, \ + .uV_step = STEP_6_25_MV, \ .n_voltages = S2MPS11_BUCK_N_VOLTAGES, \ .ramp_delay = S2MPS11_RAMP_DELAY, \ .vsel_reg = S2MPS11_REG_B1CTRL2 + (num - 1) * 2, \ @@ -306,8 +292,8 @@ static struct regulator_ops s2mps11_buck_ops = { .ops = &s2mps11_buck_ops, \ .type = REGULATOR_VOLTAGE, \ .owner = THIS_MODULE, \ - .min_uV = S2MPS11_BUCK_MIN1, \ - .uV_step = S2MPS11_BUCK_STEP1, \ + .min_uV = MIN_600_MV, \ + .uV_step = STEP_6_25_MV, \ .n_voltages = S2MPS11_BUCK_N_VOLTAGES, \ .ramp_delay = S2MPS11_RAMP_DELAY, \ .vsel_reg = S2MPS11_REG_B5CTRL2, \ @@ -316,14 +302,14 @@ static struct regulator_ops s2mps11_buck_ops = { .enable_mask = S2MPS11_ENABLE_MASK \ } -#define regulator_desc_s2mps11_buck6_8(num) { \ +#define regulator_desc_s2mps11_buck6_10(num, min, step) { \ .name = "BUCK"#num, \ .id = S2MPS11_BUCK##num, \ .ops = &s2mps11_buck_ops, \ .type = REGULATOR_VOLTAGE, \ .owner = THIS_MODULE, \ - .min_uV = S2MPS11_BUCK_MIN1, \ - .uV_step = S2MPS11_BUCK_STEP1, \ + .min_uV = min, \ + .uV_step = step, \ .n_voltages = S2MPS11_BUCK_N_VOLTAGES, \ .ramp_delay = S2MPS11_RAMP_DELAY, \ .vsel_reg = S2MPS11_REG_B6CTRL2 + (num - 6) * 2, \ @@ -332,87 +318,55 @@ static struct regulator_ops s2mps11_buck_ops = { .enable_mask = S2MPS11_ENABLE_MASK \ } -#define regulator_desc_s2mps11_buck9 { \ - .name = "BUCK9", \ - .id = S2MPS11_BUCK9, \ - .ops = &s2mps11_buck_ops, \ - .type = REGULATOR_VOLTAGE, \ - .owner = THIS_MODULE, \ - .min_uV = S2MPS11_BUCK_MIN3, \ - .uV_step = S2MPS11_BUCK_STEP3, \ - .n_voltages = S2MPS11_BUCK_N_VOLTAGES, \ - .ramp_delay = S2MPS11_RAMP_DELAY, \ - .vsel_reg = S2MPS11_REG_B9CTRL2, \ - .vsel_mask = S2MPS11_BUCK_VSEL_MASK, \ - .enable_reg = S2MPS11_REG_B9CTRL1, \ - .enable_mask = S2MPS11_ENABLE_MASK \ -} - -#define regulator_desc_s2mps11_buck10 { \ - .name = "BUCK10", \ - .id = S2MPS11_BUCK10, \ - .ops = &s2mps11_buck_ops, \ - .type = REGULATOR_VOLTAGE, \ - .owner = THIS_MODULE, \ - .min_uV = S2MPS11_BUCK_MIN2, \ - .uV_step = S2MPS11_BUCK_STEP2, \ - .n_voltages = S2MPS11_BUCK_N_VOLTAGES, \ - .ramp_delay = S2MPS11_RAMP_DELAY, \ - .vsel_reg = S2MPS11_REG_B10CTRL2, \ - .vsel_mask = S2MPS11_BUCK_VSEL_MASK, \ - .enable_reg = S2MPS11_REG_B10CTRL1, \ - .enable_mask = S2MPS11_ENABLE_MASK \ -} - static const struct regulator_desc s2mps11_regulators[] = { - regulator_desc_s2mps11_ldo2(1), - regulator_desc_s2mps11_ldo1(2), - regulator_desc_s2mps11_ldo1(3), - regulator_desc_s2mps11_ldo1(4), - regulator_desc_s2mps11_ldo1(5), - regulator_desc_s2mps11_ldo2(6), - regulator_desc_s2mps11_ldo1(7), - regulator_desc_s2mps11_ldo1(8), - regulator_desc_s2mps11_ldo1(9), - regulator_desc_s2mps11_ldo1(10), - regulator_desc_s2mps11_ldo2(11), - regulator_desc_s2mps11_ldo1(12), - regulator_desc_s2mps11_ldo1(13), - regulator_desc_s2mps11_ldo1(14), - regulator_desc_s2mps11_ldo1(15), - regulator_desc_s2mps11_ldo1(16), - regulator_desc_s2mps11_ldo1(17), - regulator_desc_s2mps11_ldo1(18), - regulator_desc_s2mps11_ldo1(19), - regulator_desc_s2mps11_ldo1(20), - regulator_desc_s2mps11_ldo1(21), - regulator_desc_s2mps11_ldo2(22), - regulator_desc_s2mps11_ldo2(23), - regulator_desc_s2mps11_ldo1(24), - regulator_desc_s2mps11_ldo1(25), - regulator_desc_s2mps11_ldo1(26), - regulator_desc_s2mps11_ldo2(27), - regulator_desc_s2mps11_ldo1(28), - regulator_desc_s2mps11_ldo1(29), - regulator_desc_s2mps11_ldo1(30), - regulator_desc_s2mps11_ldo1(31), - regulator_desc_s2mps11_ldo1(32), - regulator_desc_s2mps11_ldo1(33), - regulator_desc_s2mps11_ldo1(34), - regulator_desc_s2mps11_ldo1(35), - regulator_desc_s2mps11_ldo1(36), - regulator_desc_s2mps11_ldo1(37), - regulator_desc_s2mps11_ldo1(38), + regulator_desc_s2mps11_ldo(1, STEP_25_MV), + regulator_desc_s2mps11_ldo(2, STEP_50_MV), + regulator_desc_s2mps11_ldo(3, STEP_50_MV), + regulator_desc_s2mps11_ldo(4, STEP_50_MV), + regulator_desc_s2mps11_ldo(5, STEP_50_MV), + regulator_desc_s2mps11_ldo(6, STEP_25_MV), + regulator_desc_s2mps11_ldo(7, STEP_50_MV), + regulator_desc_s2mps11_ldo(8, STEP_50_MV), + regulator_desc_s2mps11_ldo(9, STEP_50_MV), + regulator_desc_s2mps11_ldo(10, STEP_50_MV), + regulator_desc_s2mps11_ldo(11, STEP_25_MV), + regulator_desc_s2mps11_ldo(12, STEP_50_MV), + regulator_desc_s2mps11_ldo(13, STEP_50_MV), + regulator_desc_s2mps11_ldo(14, STEP_50_MV), + regulator_desc_s2mps11_ldo(15, STEP_50_MV), + regulator_desc_s2mps11_ldo(16, STEP_50_MV), + regulator_desc_s2mps11_ldo(17, STEP_50_MV), + regulator_desc_s2mps11_ldo(18, STEP_50_MV), + regulator_desc_s2mps11_ldo(19, STEP_50_MV), + regulator_desc_s2mps11_ldo(20, STEP_50_MV), + regulator_desc_s2mps11_ldo(21, STEP_50_MV), + regulator_desc_s2mps11_ldo(22, STEP_25_MV), + regulator_desc_s2mps11_ldo(23, STEP_25_MV), + regulator_desc_s2mps11_ldo(24, STEP_50_MV), + regulator_desc_s2mps11_ldo(25, STEP_50_MV), + regulator_desc_s2mps11_ldo(26, STEP_50_MV), + regulator_desc_s2mps11_ldo(27, STEP_25_MV), + regulator_desc_s2mps11_ldo(28, STEP_50_MV), + regulator_desc_s2mps11_ldo(29, STEP_50_MV), + regulator_desc_s2mps11_ldo(30, STEP_50_MV), + regulator_desc_s2mps11_ldo(31, STEP_50_MV), + regulator_desc_s2mps11_ldo(32, STEP_50_MV), + regulator_desc_s2mps11_ldo(33, STEP_50_MV), + regulator_desc_s2mps11_ldo(34, STEP_50_MV), + regulator_desc_s2mps11_ldo(35, STEP_50_MV), + regulator_desc_s2mps11_ldo(36, STEP_50_MV), + regulator_desc_s2mps11_ldo(37, STEP_50_MV), + regulator_desc_s2mps11_ldo(38, STEP_50_MV), regulator_desc_s2mps11_buck1_4(1), regulator_desc_s2mps11_buck1_4(2), regulator_desc_s2mps11_buck1_4(3), regulator_desc_s2mps11_buck1_4(4), regulator_desc_s2mps11_buck5, - regulator_desc_s2mps11_buck6_8(6), - regulator_desc_s2mps11_buck6_8(7), - regulator_desc_s2mps11_buck6_8(8), - regulator_desc_s2mps11_buck9, - regulator_desc_s2mps11_buck10, + regulator_desc_s2mps11_buck6_10(6, MIN_600_MV, STEP_6_25_MV), + regulator_desc_s2mps11_buck6_10(7, MIN_600_MV, STEP_6_25_MV), + regulator_desc_s2mps11_buck6_10(8, MIN_600_MV, STEP_6_25_MV), + regulator_desc_s2mps11_buck6_10(9, MIN_3000_MV, STEP_25_MV), + regulator_desc_s2mps11_buck6_10(10, MIN_750_MV, STEP_12_5_MV), }; static int s2mps14_regulator_enable(struct regulator_dev *rdev) @@ -510,56 +464,29 @@ static struct regulator_ops s2mps14_reg_ops = { .set_suspend_disable = s2mps14_regulator_set_suspend_disable, }; -#define regulator_desc_s2mps14_ldo1(num) { \ - .name = "LDO"#num, \ - .id = S2MPS14_LDO##num, \ - .ops = &s2mps14_reg_ops, \ - .type = REGULATOR_VOLTAGE, \ - .owner = THIS_MODULE, \ - .min_uV = S2MPS14_LDO_MIN_800MV, \ - .uV_step = S2MPS14_LDO_STEP_25MV, \ - .n_voltages = S2MPS14_LDO_N_VOLTAGES, \ - .vsel_reg = S2MPS14_REG_L1CTRL + num - 1, \ - .vsel_mask = S2MPS14_LDO_VSEL_MASK, \ - .enable_reg = S2MPS14_REG_L1CTRL + num - 1, \ - .enable_mask = S2MPS14_ENABLE_MASK \ -} -#define regulator_desc_s2mps14_ldo2(num) { \ - .name = "LDO"#num, \ - .id = S2MPS14_LDO##num, \ - .ops = &s2mps14_reg_ops, \ - .type = REGULATOR_VOLTAGE, \ - .owner = THIS_MODULE, \ - .min_uV = S2MPS14_LDO_MIN_1800MV, \ - .uV_step = S2MPS14_LDO_STEP_25MV, \ - .n_voltages = S2MPS14_LDO_N_VOLTAGES, \ - .vsel_reg = S2MPS14_REG_L1CTRL + num - 1, \ - .vsel_mask = S2MPS14_LDO_VSEL_MASK, \ - .enable_reg = S2MPS14_REG_L1CTRL + num - 1, \ - .enable_mask = S2MPS14_ENABLE_MASK \ -} -#define regulator_desc_s2mps14_ldo3(num) { \ +#define regulator_desc_s2mps14_ldo(num, min, step) { \ .name = "LDO"#num, \ .id = S2MPS14_LDO##num, \ .ops = &s2mps14_reg_ops, \ .type = REGULATOR_VOLTAGE, \ .owner = THIS_MODULE, \ - .min_uV = S2MPS14_LDO_MIN_800MV, \ - .uV_step = S2MPS14_LDO_STEP_12_5MV, \ + .min_uV = min, \ + .uV_step = step, \ .n_voltages = S2MPS14_LDO_N_VOLTAGES, \ .vsel_reg = S2MPS14_REG_L1CTRL + num - 1, \ .vsel_mask = S2MPS14_LDO_VSEL_MASK, \ .enable_reg = S2MPS14_REG_L1CTRL + num - 1, \ .enable_mask = S2MPS14_ENABLE_MASK \ } -#define regulator_desc_s2mps14_buck1235(num) { \ + +#define regulator_desc_s2mps14_buck(num, min, step) { \ .name = "BUCK"#num, \ .id = S2MPS14_BUCK##num, \ .ops = &s2mps14_reg_ops, \ .type = REGULATOR_VOLTAGE, \ .owner = THIS_MODULE, \ - .min_uV = S2MPS14_BUCK1235_MIN_600MV, \ - .uV_step = S2MPS14_BUCK1235_STEP_6_25MV, \ + .min_uV = min, \ + .uV_step = step, \ .n_voltages = S2MPS14_BUCK_N_VOLTAGES, \ .linear_min_sel = S2MPS14_BUCK1235_START_SEL, \ .ramp_delay = S2MPS14_BUCK_RAMP_DELAY, \ @@ -568,54 +495,38 @@ static struct regulator_ops s2mps14_reg_ops = { .enable_reg = S2MPS14_REG_B1CTRL1 + (num - 1) * 2, \ .enable_mask = S2MPS14_ENABLE_MASK \ } -#define regulator_desc_s2mps14_buck4(num) { \ - .name = "BUCK"#num, \ - .id = S2MPS14_BUCK##num, \ - .ops = &s2mps14_reg_ops, \ - .type = REGULATOR_VOLTAGE, \ - .owner = THIS_MODULE, \ - .min_uV = S2MPS14_BUCK4_MIN_1400MV, \ - .uV_step = S2MPS14_BUCK4_STEP_12_5MV, \ - .n_voltages = S2MPS14_BUCK_N_VOLTAGES, \ - .linear_min_sel = S2MPS14_BUCK4_START_SEL, \ - .ramp_delay = S2MPS14_BUCK_RAMP_DELAY, \ - .vsel_reg = S2MPS14_REG_B1CTRL2 + (num - 1) * 2, \ - .vsel_mask = S2MPS14_BUCK_VSEL_MASK, \ - .enable_reg = S2MPS14_REG_B1CTRL1 + (num - 1) * 2, \ - .enable_mask = S2MPS14_ENABLE_MASK \ -} static const struct regulator_desc s2mps14_regulators[] = { - regulator_desc_s2mps14_ldo3(1), - regulator_desc_s2mps14_ldo3(2), - regulator_desc_s2mps14_ldo1(3), - regulator_desc_s2mps14_ldo1(4), - regulator_desc_s2mps14_ldo3(5), - regulator_desc_s2mps14_ldo3(6), - regulator_desc_s2mps14_ldo1(7), - regulator_desc_s2mps14_ldo2(8), - regulator_desc_s2mps14_ldo3(9), - regulator_desc_s2mps14_ldo3(10), - regulator_desc_s2mps14_ldo1(11), - regulator_desc_s2mps14_ldo2(12), - regulator_desc_s2mps14_ldo2(13), - regulator_desc_s2mps14_ldo2(14), - regulator_desc_s2mps14_ldo2(15), - regulator_desc_s2mps14_ldo2(16), - regulator_desc_s2mps14_ldo2(17), - regulator_desc_s2mps14_ldo2(18), - regulator_desc_s2mps14_ldo1(19), - regulator_desc_s2mps14_ldo1(20), - regulator_desc_s2mps14_ldo1(21), - regulator_desc_s2mps14_ldo3(22), - regulator_desc_s2mps14_ldo1(23), - regulator_desc_s2mps14_ldo2(24), - regulator_desc_s2mps14_ldo2(25), - regulator_desc_s2mps14_buck1235(1), - regulator_desc_s2mps14_buck1235(2), - regulator_desc_s2mps14_buck1235(3), - regulator_desc_s2mps14_buck4(4), - regulator_desc_s2mps14_buck1235(5), + regulator_desc_s2mps14_ldo(1, MIN_800_MV, STEP_12_5_MV), + regulator_desc_s2mps14_ldo(2, MIN_800_MV, STEP_12_5_MV), + regulator_desc_s2mps14_ldo(3, MIN_800_MV, STEP_25_MV), + regulator_desc_s2mps14_ldo(4, MIN_800_MV, STEP_25_MV), + regulator_desc_s2mps14_ldo(5, MIN_800_MV, STEP_12_5_MV), + regulator_desc_s2mps14_ldo(6, MIN_800_MV, STEP_12_5_MV), + regulator_desc_s2mps14_ldo(7, MIN_800_MV, STEP_25_MV), + regulator_desc_s2mps14_ldo(8, MIN_1800_MV, STEP_25_MV), + regulator_desc_s2mps14_ldo(9, MIN_800_MV, STEP_12_5_MV), + regulator_desc_s2mps14_ldo(10, MIN_800_MV, STEP_12_5_MV), + regulator_desc_s2mps14_ldo(11, MIN_800_MV, STEP_25_MV), + regulator_desc_s2mps14_ldo(12, MIN_1800_MV, STEP_25_MV), + regulator_desc_s2mps14_ldo(13, MIN_1800_MV, STEP_25_MV), + regulator_desc_s2mps14_ldo(14, MIN_1800_MV, STEP_25_MV), + regulator_desc_s2mps14_ldo(15, MIN_1800_MV, STEP_25_MV), + regulator_desc_s2mps14_ldo(16, MIN_1800_MV, STEP_25_MV), + regulator_desc_s2mps14_ldo(17, MIN_1800_MV, STEP_25_MV), + regulator_desc_s2mps14_ldo(18, MIN_1800_MV, STEP_25_MV), + regulator_desc_s2mps14_ldo(19, MIN_800_MV, STEP_25_MV), + regulator_desc_s2mps14_ldo(20, MIN_800_MV, STEP_25_MV), + regulator_desc_s2mps14_ldo(21, MIN_800_MV, STEP_25_MV), + regulator_desc_s2mps14_ldo(22, MIN_800_MV, STEP_12_5_MV), + regulator_desc_s2mps14_ldo(23, MIN_800_MV, STEP_25_MV), + regulator_desc_s2mps14_ldo(24, MIN_1800_MV, STEP_25_MV), + regulator_desc_s2mps14_ldo(25, MIN_1800_MV, STEP_25_MV), + regulator_desc_s2mps14_buck(1, MIN_600_MV, STEP_6_25_MV), + regulator_desc_s2mps14_buck(2, MIN_600_MV, STEP_6_25_MV), + regulator_desc_s2mps14_buck(3, MIN_600_MV, STEP_6_25_MV), + regulator_desc_s2mps14_buck(4, MIN_1400_MV, STEP_12_5_MV), + regulator_desc_s2mps14_buck(5, MIN_600_MV, STEP_6_25_MV), }; static int s2mps14_pmic_enable_ext_control(struct s2mps11_info *s2mps11, diff --git a/drivers/regulator/sky81452-regulator.c b/drivers/regulator/sky81452-regulator.c new file mode 100644 index 0000000..97aff0c --- /dev/null +++ b/drivers/regulator/sky81452-regulator.c @@ -0,0 +1,130 @@ +/* + * sky81452-regulator.c SKY81452 regulator driver + * + * Copyright 2014 Skyworks Solutions Inc. + * Author : Gyungoh Yoo <jack.yoo@skyworksinc.com> + * + * This program is free software; you can redistribute it and/or modify it + * under the terms of the GNU General Public License as published by the + * Free Software Foundation; either version 2, or (at your option) any + * later version. + * + * This program is distributed in the hope that it will be useful, but + * WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU + * General Public License for more details. + * + * You should have received a copy of the GNU General Public License along + * with this program; if not, see <http://www.gnu.org/licenses/>. + */ + +#include <linux/module.h> +#include <linux/kernel.h> +#include <linux/platform_device.h> +#include <linux/init.h> +#include <linux/err.h> +#include <linux/of.h> +#include <linux/regulator/driver.h> +#include <linux/regulator/of_regulator.h> + +/* registers */ +#define SKY81452_REG1 0x01 +#define SKY81452_REG3 0x03 + +/* bit mask */ +#define SKY81452_LEN 0x40 +#define SKY81452_LOUT 0x1F + +static struct regulator_ops sky81452_reg_ops = { + .list_voltage = regulator_list_voltage_linear_range, + .map_voltage = regulator_map_voltage_linear_range, + .get_voltage_sel = regulator_get_voltage_sel_regmap, + .set_voltage_sel = regulator_set_voltage_sel_regmap, + .enable = regulator_enable_regmap, + .disable = regulator_disable_regmap, + .is_enabled = regulator_is_enabled_regmap, +}; + +static const struct regulator_linear_range sky81452_reg_ranges[] = { + REGULATOR_LINEAR_RANGE(4500000, 0, 14, 250000), + REGULATOR_LINEAR_RANGE(9000000, 15, 31, 1000000), +}; + +static const struct regulator_desc sky81452_reg = { + .name = "LOUT", + .ops = &sky81452_reg_ops, + .type = REGULATOR_VOLTAGE, + .owner = THIS_MODULE, + .n_voltages = SKY81452_LOUT + 1, + .linear_ranges = sky81452_reg_ranges, + .n_linear_ranges = ARRAY_SIZE(sky81452_reg_ranges), + .vsel_reg = SKY81452_REG3, + .vsel_mask = SKY81452_LOUT, + .enable_reg = SKY81452_REG1, + .enable_mask = SKY81452_LEN, +}; + +#ifdef CONFIG_OF +static struct regulator_init_data *sky81452_reg_parse_dt(struct device *dev) +{ + struct regulator_init_data *init_data; + struct device_node *np; + + np = of_get_child_by_name(dev->parent->of_node, "regulator"); + if (unlikely(!np)) { + dev_err(dev, "regulator node not found"); + return NULL; + } + + init_data = of_get_regulator_init_data(dev, np); + + of_node_put(np); + return init_data; +} +#else +static struct regulator_init_data *sky81452_reg_parse_dt(struct device *dev) +{ + return ERR_PTR(-EINVAL); +} +#endif + +static int sky81452_reg_probe(struct platform_device *pdev) +{ + struct device *dev = &pdev->dev; + const struct regulator_init_data *init_data = dev_get_platdata(dev); + struct regulator_config config = { }; + struct regulator_dev *rdev; + + if (!init_data) { + init_data = sky81452_reg_parse_dt(dev); + if (IS_ERR(init_data)) + return PTR_ERR(init_data); + } + + config.dev = dev; + config.init_data = init_data; + config.of_node = dev->of_node; + config.regmap = dev_get_drvdata(dev->parent); + + rdev = devm_regulator_register(dev, &sky81452_reg, &config); + if (IS_ERR(rdev)) + return PTR_ERR(rdev); + + platform_set_drvdata(pdev, rdev); + + return 0; +} + +static struct platform_driver sky81452_reg_driver = { + .driver = { + .name = "sky81452-regulator", + }, + .probe = sky81452_reg_probe, +}; + +module_platform_driver(sky81452_reg_driver); + +MODULE_DESCRIPTION("Skyworks SKY81452 Regulator driver"); +MODULE_AUTHOR("Gyungoh Yoo <jack.yoo@skyworksinc.com>"); +MODULE_LICENSE("GPL"); +MODULE_VERSION("1.0"); diff --git a/drivers/regulator/st-pwm.c b/drivers/regulator/st-pwm.c deleted file mode 100644 index 5ea78df..0000000 --- a/drivers/regulator/st-pwm.c +++ /dev/null @@ -1,190 +0,0 @@ -/* - * Regulator driver for ST's PWM Regulators - * - * Copyright (C) 2014 - STMicroelectronics Inc. - * - * Author: Lee Jones <lee.jones@linaro.org> - * - * This program is free software; you can redistribute it and/or modify - * it under the terms of the GNU General Public License version 2 as - * published by the Free Software Foundation. - */ - -#include <linux/module.h> -#include <linux/init.h> -#include <linux/err.h> -#include <linux/regulator/driver.h> -#include <linux/regulator/machine.h> -#include <linux/regulator/of_regulator.h> -#include <linux/of.h> -#include <linux/of_device.h> -#include <linux/pwm.h> - -#define ST_PWM_REG_PERIOD 8448 - -struct st_pwm_regulator_pdata { - const struct regulator_desc *desc; - struct st_pwm_voltages *duty_cycle_table; -}; - -struct st_pwm_regulator_data { - const struct st_pwm_regulator_pdata *pdata; - struct pwm_device *pwm; - bool enabled; - int state; -}; - -struct st_pwm_voltages { - unsigned int uV; - unsigned int dutycycle; -}; - -static int st_pwm_regulator_get_voltage_sel(struct regulator_dev *dev) -{ - struct st_pwm_regulator_data *drvdata = rdev_get_drvdata(dev); - - return drvdata->state; -} - -static int st_pwm_regulator_set_voltage_sel(struct regulator_dev *dev, - unsigned selector) -{ - struct st_pwm_regulator_data *drvdata = rdev_get_drvdata(dev); - int dutycycle; - int ret; - - dutycycle = (ST_PWM_REG_PERIOD / 100) * - drvdata->pdata->duty_cycle_table[selector].dutycycle; - - ret = pwm_config(drvdata->pwm, dutycycle, ST_PWM_REG_PERIOD); - if (ret) { - dev_err(&dev->dev, "Failed to configure PWM\n"); - return ret; - } - - drvdata->state = selector; - - if (!drvdata->enabled) { - ret = pwm_enable(drvdata->pwm); - if (ret) { - dev_err(&dev->dev, "Failed to enable PWM\n"); - return ret; - } - drvdata->enabled = true; - } - - return 0; -} - -static int st_pwm_regulator_list_voltage(struct regulator_dev *dev, - unsigned selector) -{ - struct st_pwm_regulator_data *drvdata = rdev_get_drvdata(dev); - - if (selector >= dev->desc->n_voltages) - return -EINVAL; - - return drvdata->pdata->duty_cycle_table[selector].uV; -} - -static struct regulator_ops st_pwm_regulator_voltage_ops = { - .set_voltage_sel = st_pwm_regulator_set_voltage_sel, - .get_voltage_sel = st_pwm_regulator_get_voltage_sel, - .list_voltage = st_pwm_regulator_list_voltage, - .map_voltage = regulator_map_voltage_iterate, -}; - -static struct st_pwm_voltages b2105_duty_cycle_table[] = { - { .uV = 1114000, .dutycycle = 0, }, - { .uV = 1095000, .dutycycle = 10, }, - { .uV = 1076000, .dutycycle = 20, }, - { .uV = 1056000, .dutycycle = 30, }, - { .uV = 1036000, .dutycycle = 40, }, - { .uV = 1016000, .dutycycle = 50, }, - /* WARNING: Values above 50% duty-cycle cause boot failures. */ -}; - -static const struct regulator_desc b2105_desc = { - .name = "b2105-pwm-regulator", - .ops = &st_pwm_regulator_voltage_ops, - .type = REGULATOR_VOLTAGE, - .owner = THIS_MODULE, - .n_voltages = ARRAY_SIZE(b2105_duty_cycle_table), - .supply_name = "pwm", -}; - -static const struct st_pwm_regulator_pdata b2105_info = { - .desc = &b2105_desc, - .duty_cycle_table = b2105_duty_cycle_table, -}; - -static const struct of_device_id st_pwm_of_match[] = { - { .compatible = "st,b2105-pwm-regulator", .data = &b2105_info, }, - { }, -}; -MODULE_DEVICE_TABLE(of, st_pwm_of_match); - -static int st_pwm_regulator_probe(struct platform_device *pdev) -{ - struct st_pwm_regulator_data *drvdata; - struct regulator_dev *regulator; - struct regulator_config config = { }; - struct device_node *np = pdev->dev.of_node; - const struct of_device_id *of_match; - - if (!np) { - dev_err(&pdev->dev, "Device Tree node missing\n"); - return -EINVAL; - } - - drvdata = devm_kzalloc(&pdev->dev, sizeof(*drvdata), GFP_KERNEL); - if (!drvdata) - return -ENOMEM; - - of_match = of_match_device(st_pwm_of_match, &pdev->dev); - if (!of_match) { - dev_err(&pdev->dev, "failed to match of device\n"); - return -ENODEV; - } - drvdata->pdata = of_match->data; - - config.init_data = of_get_regulator_init_data(&pdev->dev, np); - if (!config.init_data) - return -ENOMEM; - - config.of_node = np; - config.dev = &pdev->dev; - config.driver_data = drvdata; - - drvdata->pwm = devm_pwm_get(&pdev->dev, NULL); - if (IS_ERR(drvdata->pwm)) { - dev_err(&pdev->dev, "Failed to get PWM\n"); - return PTR_ERR(drvdata->pwm); - } - - regulator = devm_regulator_register(&pdev->dev, - drvdata->pdata->desc, &config); - if (IS_ERR(regulator)) { - dev_err(&pdev->dev, "Failed to register regulator %s\n", - drvdata->pdata->desc->name); - return PTR_ERR(regulator); - } - - return 0; -} - -static struct platform_driver st_pwm_regulator_driver = { - .driver = { - .name = "st-pwm-regulator", - .owner = THIS_MODULE, - .of_match_table = of_match_ptr(st_pwm_of_match), - }, - .probe = st_pwm_regulator_probe, -}; - -module_platform_driver(st_pwm_regulator_driver); - -MODULE_LICENSE("GPL"); -MODULE_AUTHOR("Lee Jones <lee.jones@linaro.org>"); -MODULE_DESCRIPTION("ST PWM Regulator Driver"); -MODULE_ALIAS("platform:st_pwm-regulator"); diff --git a/drivers/regulator/tps65023-regulator.c b/drivers/regulator/tps65023-regulator.c index 3ef67a8..7380af8 100644 --- a/drivers/regulator/tps65023-regulator.c +++ b/drivers/regulator/tps65023-regulator.c @@ -211,9 +211,6 @@ static int tps_65023_probe(struct i2c_client *client, int i; int error; - if (!i2c_check_functionality(client->adapter, I2C_FUNC_SMBUS_BYTE_DATA)) - return -EIO; - /** * init_data points to array of regulator_init structures * coming from the board-evm file. diff --git a/drivers/regulator/tps65217-regulator.c b/drivers/regulator/tps65217-regulator.c index d58db72..adbe4fc 100644 --- a/drivers/regulator/tps65217-regulator.c +++ b/drivers/regulator/tps65217-regulator.c @@ -27,10 +27,13 @@ #include <linux/regulator/machine.h> #include <linux/mfd/tps65217.h> -#define TPS65217_REGULATOR(_name, _id, _ops, _n, _vr, _vm, _em, _t, _lr, _nlr) \ +#define TPS65217_REGULATOR(_name, _id, _of_match, _ops, _n, _vr, _vm, _em, \ + _t, _lr, _nlr) \ { \ .name = _name, \ .id = _id, \ + .of_match = of_match_ptr(_of_match), \ + .regulators_node= of_match_ptr("regulators"), \ .ops = &_ops, \ .n_voltages = _n, \ .type = REGULATOR_VOLTAGE, \ @@ -138,87 +141,40 @@ static struct regulator_ops tps65217_pmic_ldo1_ops = { }; static const struct regulator_desc regulators[] = { - TPS65217_REGULATOR("DCDC1", TPS65217_DCDC_1, tps65217_pmic_ops, 64, - TPS65217_REG_DEFDCDC1, TPS65217_DEFDCDCX_DCDC_MASK, - TPS65217_ENABLE_DC1_EN, NULL, tps65217_uv1_ranges, - 2), /* DCDC1 voltage range: 900000 ~ 1800000 */ - TPS65217_REGULATOR("DCDC2", TPS65217_DCDC_2, tps65217_pmic_ops, 64, - TPS65217_REG_DEFDCDC2, TPS65217_DEFDCDCX_DCDC_MASK, - TPS65217_ENABLE_DC2_EN, NULL, tps65217_uv1_ranges, + TPS65217_REGULATOR("DCDC1", TPS65217_DCDC_1, "dcdc1", + tps65217_pmic_ops, 64, TPS65217_REG_DEFDCDC1, + TPS65217_DEFDCDCX_DCDC_MASK, TPS65217_ENABLE_DC1_EN, + NULL, tps65217_uv1_ranges, 2), + TPS65217_REGULATOR("DCDC2", TPS65217_DCDC_2, "dcdc2", + tps65217_pmic_ops, 64, TPS65217_REG_DEFDCDC2, + TPS65217_DEFDCDCX_DCDC_MASK, TPS65217_ENABLE_DC2_EN, + NULL, tps65217_uv1_ranges, ARRAY_SIZE(tps65217_uv1_ranges)), - TPS65217_REGULATOR("DCDC3", TPS65217_DCDC_3, tps65217_pmic_ops, 64, - TPS65217_REG_DEFDCDC3, TPS65217_DEFDCDCX_DCDC_MASK, - TPS65217_ENABLE_DC3_EN, NULL, tps65217_uv1_ranges, - 1), /* DCDC3 voltage range: 900000 ~ 1500000 */ - TPS65217_REGULATOR("LDO1", TPS65217_LDO_1, tps65217_pmic_ldo1_ops, 16, - TPS65217_REG_DEFLDO1, TPS65217_DEFLDO1_LDO1_MASK, - TPS65217_ENABLE_LDO1_EN, LDO1_VSEL_table, NULL, 0), - TPS65217_REGULATOR("LDO2", TPS65217_LDO_2, tps65217_pmic_ops, 64, - TPS65217_REG_DEFLDO2, TPS65217_DEFLDO2_LDO2_MASK, - TPS65217_ENABLE_LDO2_EN, NULL, tps65217_uv1_ranges, + TPS65217_REGULATOR("DCDC3", TPS65217_DCDC_3, "dcdc3", + tps65217_pmic_ops, 64, TPS65217_REG_DEFDCDC3, + TPS65217_DEFDCDCX_DCDC_MASK, TPS65217_ENABLE_DC3_EN, + NULL, tps65217_uv1_ranges, 1), + TPS65217_REGULATOR("LDO1", TPS65217_LDO_1, "ldo1", + tps65217_pmic_ldo1_ops, 16, TPS65217_REG_DEFLDO1, + TPS65217_DEFLDO1_LDO1_MASK, TPS65217_ENABLE_LDO1_EN, + LDO1_VSEL_table, NULL, 0), + TPS65217_REGULATOR("LDO2", TPS65217_LDO_2, "ldo2", tps65217_pmic_ops, + 64, TPS65217_REG_DEFLDO2, + TPS65217_DEFLDO2_LDO2_MASK, TPS65217_ENABLE_LDO2_EN, + NULL, tps65217_uv1_ranges, ARRAY_SIZE(tps65217_uv1_ranges)), - TPS65217_REGULATOR("LDO3", TPS65217_LDO_3, tps65217_pmic_ops, 32, - TPS65217_REG_DEFLS1, TPS65217_DEFLDO3_LDO3_MASK, + TPS65217_REGULATOR("LDO3", TPS65217_LDO_3, "ldo3", tps65217_pmic_ops, + 32, TPS65217_REG_DEFLS1, TPS65217_DEFLDO3_LDO3_MASK, TPS65217_ENABLE_LS1_EN | TPS65217_DEFLDO3_LDO3_EN, NULL, tps65217_uv2_ranges, ARRAY_SIZE(tps65217_uv2_ranges)), - TPS65217_REGULATOR("LDO4", TPS65217_LDO_4, tps65217_pmic_ops, 32, - TPS65217_REG_DEFLS2, TPS65217_DEFLDO4_LDO4_MASK, + TPS65217_REGULATOR("LDO4", TPS65217_LDO_4, "ldo4", tps65217_pmic_ops, + 32, TPS65217_REG_DEFLS2, TPS65217_DEFLDO4_LDO4_MASK, TPS65217_ENABLE_LS2_EN | TPS65217_DEFLDO4_LDO4_EN, NULL, tps65217_uv2_ranges, ARRAY_SIZE(tps65217_uv2_ranges)), }; -#ifdef CONFIG_OF -static struct of_regulator_match reg_matches[] = { - { .name = "dcdc1", .driver_data = (void *)TPS65217_DCDC_1 }, - { .name = "dcdc2", .driver_data = (void *)TPS65217_DCDC_2 }, - { .name = "dcdc3", .driver_data = (void *)TPS65217_DCDC_3 }, - { .name = "ldo1", .driver_data = (void *)TPS65217_LDO_1 }, - { .name = "ldo2", .driver_data = (void *)TPS65217_LDO_2 }, - { .name = "ldo3", .driver_data = (void *)TPS65217_LDO_3 }, - { .name = "ldo4", .driver_data = (void *)TPS65217_LDO_4 }, -}; - -static struct tps65217_board *tps65217_parse_dt(struct platform_device *pdev) -{ - struct tps65217 *tps = dev_get_drvdata(pdev->dev.parent); - struct device_node *node = tps->dev->of_node; - struct tps65217_board *pdata; - struct device_node *regs; - int i, count; - - regs = of_get_child_by_name(node, "regulators"); - if (!regs) - return NULL; - - count = of_regulator_match(&pdev->dev, regs, reg_matches, - TPS65217_NUM_REGULATOR); - of_node_put(regs); - if ((count < 0) || (count > TPS65217_NUM_REGULATOR)) - return NULL; - - pdata = devm_kzalloc(&pdev->dev, sizeof(*pdata), GFP_KERNEL); - if (!pdata) - return NULL; - - for (i = 0; i < count; i++) { - if (!reg_matches[i].of_node) - continue; - - pdata->tps65217_init_data[i] = reg_matches[i].init_data; - pdata->of_node[i] = reg_matches[i].of_node; - } - - return pdata; -} -#else -static struct tps65217_board *tps65217_parse_dt(struct platform_device *pdev) -{ - return NULL; -} -#endif - static int tps65217_regulator_probe(struct platform_device *pdev) { struct tps65217 *tps = dev_get_drvdata(pdev->dev.parent); @@ -227,14 +183,6 @@ static int tps65217_regulator_probe(struct platform_device *pdev) struct regulator_config config = { }; int i; - if (tps->dev->of_node) - pdata = tps65217_parse_dt(pdev); - - if (!pdata) { - dev_err(&pdev->dev, "Platform data not found\n"); - return -EINVAL; - } - if (tps65217_chip_id(tps) != TPS65217) { dev_err(&pdev->dev, "Invalid tps chip version\n"); return -ENODEV; @@ -245,11 +193,10 @@ static int tps65217_regulator_probe(struct platform_device *pdev) for (i = 0; i < TPS65217_NUM_REGULATOR; i++) { /* Register the regulators */ config.dev = tps->dev; - config.init_data = pdata->tps65217_init_data[i]; + if (pdata) + config.init_data = pdata->tps65217_init_data[i]; config.driver_data = tps; config.regmap = tps->regmap; - if (tps->dev->of_node) - config.of_node = pdata->of_node[i]; rdev = devm_regulator_register(&pdev->dev, ®ulators[i], &config); @@ -259,6 +206,7 @@ static int tps65217_regulator_probe(struct platform_device *pdev) return PTR_ERR(rdev); } } + return 0; } diff --git a/drivers/regulator/tps65910-regulator.c b/drivers/regulator/tps65910-regulator.c index e584c99..18fc991 100644 --- a/drivers/regulator/tps65910-regulator.c +++ b/drivers/regulator/tps65910-regulator.c @@ -1047,7 +1047,7 @@ static struct tps65910_board *tps65910_parse_dt_reg_data( *tps65910_reg_matches = matches; for (idx = 0; idx < count; idx++) { - if (!matches[idx].init_data || !matches[idx].of_node) + if (!matches[idx].of_node) continue; pmic_plat_data->tps65910_pmic_init_data[idx] = @@ -1077,7 +1077,6 @@ static int tps65910_probe(struct platform_device *pdev) struct tps65910 *tps65910 = dev_get_drvdata(pdev->dev.parent); struct regulator_config config = { }; struct tps_info *info; - struct regulator_init_data *reg_data; struct regulator_dev *rdev; struct tps65910_reg *pmic; struct tps65910_board *pmic_plat_data; @@ -1140,14 +1139,6 @@ static int tps65910_probe(struct platform_device *pdev) for (i = 0; i < pmic->num_regulators && i < TPS65910_NUM_REGS; i++, info++) { - - reg_data = pmic_plat_data->tps65910_pmic_init_data[i]; - - /* Regulator API handles empty constraints but not NULL - * constraints */ - if (!reg_data) - continue; - /* Register the regulators */ pmic->info[i] = info; @@ -1199,7 +1190,7 @@ static int tps65910_probe(struct platform_device *pdev) pmic->desc[i].enable_mask = TPS65910_SUPPLY_STATE_ENABLED; config.dev = tps65910->dev; - config.init_data = reg_data; + config.init_data = pmic_plat_data->tps65910_pmic_init_data[i]; config.driver_data = pmic; config.regmap = tps65910->regmap; |