diff options
Diffstat (limited to 'drivers/serial/serial_txx9.c')
| -rw-r--r-- | drivers/serial/serial_txx9.c | 1171 |
1 files changed, 1171 insertions, 0 deletions
diff --git a/drivers/serial/serial_txx9.c b/drivers/serial/serial_txx9.c new file mode 100644 index 0000000..dfc9873 --- /dev/null +++ b/drivers/serial/serial_txx9.c @@ -0,0 +1,1171 @@ +/* + * drivers/serial/serial_txx9.c + * + * Derived from many drivers using generic_serial interface, + * especially serial_tx3912.c by Steven J. Hill and r39xx_serial.c + * (was in Linux/VR tree) by Jim Pick. + * + * Copyright (C) 1999 Harald Koerfgen + * Copyright (C) 2000 Jim Pick <jim@jimpick.com> + * Copyright (C) 2001 Steven J. Hill (sjhill@realitydiluted.com) + * Copyright (C) 2000-2002 Toshiba Corporation + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + * + * Serial driver for TX3927/TX4927/TX4925/TX4938 internal SIO controller + * + * Revision History: + * 0.30 Initial revision. (Renamed from serial_txx927.c) + * 0.31 Use save_flags instead of local_irq_save. + * 0.32 Support SCLK. + * 0.33 Switch TXX9_TTY_NAME by CONFIG_SERIAL_TXX9_STDSERIAL. + * Support TIOCSERGETLSR. + * 0.34 Support slow baudrate. + * 0.40 Merge codes from mainstream kernel (2.4.22). + * 0.41 Fix console checking in rs_shutdown_port(). + * Disable flow-control in serial_console_write(). + * 0.42 Fix minor compiler warning. + * 1.00 Kernel 2.6. Converted to new serial core (based on 8250.c). + * 1.01 Set fifosize to make tx_empry called properly. + * Use standard uart_get_divisor. + * 1.02 Cleanup. (import 8250.c changes) + */ +#include <linux/config.h> + +#if defined(CONFIG_SERIAL_TXX9_CONSOLE) && defined(CONFIG_MAGIC_SYSRQ) +#define SUPPORT_SYSRQ +#endif + +#include <linux/module.h> +#include <linux/ioport.h> +#include <linux/init.h> +#include <linux/console.h> +#include <linux/sysrq.h> +#include <linux/delay.h> +#include <linux/device.h> +#include <linux/pci.h> +#include <linux/tty.h> +#include <linux/tty_flip.h> +#include <linux/serial_core.h> +#include <linux/serial.h> + +#include <asm/io.h> +#include <asm/irq.h> + +static char *serial_version = "1.02"; +static char *serial_name = "TX39/49 Serial driver"; + +#define PASS_LIMIT 256 + +#if !defined(CONFIG_SERIAL_TXX9_STDSERIAL) +/* "ttyS" is used for standard serial driver */ +#define TXX9_TTY_NAME "ttyTX" +#define TXX9_TTY_DEVFS_NAME "tttx/" +#define TXX9_TTY_MINOR_START (64 + 64) /* ttyTX0(128), ttyTX1(129) */ +#else +/* acts like standard serial driver */ +#define TXX9_TTY_NAME "ttyS" +#define TXX9_TTY_DEVFS_NAME "tts/" +#define TXX9_TTY_MINOR_START 64 +#endif +#define TXX9_TTY_MAJOR TTY_MAJOR + +/* flag aliases */ +#define UPF_TXX9_HAVE_CTS_LINE UPF_BUGGY_UART +#define UPF_TXX9_USE_SCLK UPF_MAGIC_MULTIPLIER + +#ifdef CONFIG_PCI +/* support for Toshiba TC86C001 SIO */ +#define ENABLE_SERIAL_TXX9_PCI +#endif + +/* + * Number of serial ports + */ +#ifdef ENABLE_SERIAL_TXX9_PCI +#define NR_PCI_BOARDS 4 +#define UART_NR (2 + NR_PCI_BOARDS) +#else +#define UART_NR 2 +#endif + +struct uart_txx9_port { + struct uart_port port; + + /* + * We provide a per-port pm hook. + */ + void (*pm)(struct uart_port *port, + unsigned int state, unsigned int old); +}; + +#define TXX9_REGION_SIZE 0x24 + +/* TXX9 Serial Registers */ +#define TXX9_SILCR 0x00 +#define TXX9_SIDICR 0x04 +#define TXX9_SIDISR 0x08 +#define TXX9_SICISR 0x0c +#define TXX9_SIFCR 0x10 +#define TXX9_SIFLCR 0x14 +#define TXX9_SIBGR 0x18 +#define TXX9_SITFIFO 0x1c +#define TXX9_SIRFIFO 0x20 + +/* SILCR : Line Control */ +#define TXX9_SILCR_SCS_MASK 0x00000060 +#define TXX9_SILCR_SCS_IMCLK 0x00000000 +#define TXX9_SILCR_SCS_IMCLK_BG 0x00000020 +#define TXX9_SILCR_SCS_SCLK 0x00000040 +#define TXX9_SILCR_SCS_SCLK_BG 0x00000060 +#define TXX9_SILCR_UEPS 0x00000010 +#define TXX9_SILCR_UPEN 0x00000008 +#define TXX9_SILCR_USBL_MASK 0x00000004 +#define TXX9_SILCR_USBL_1BIT 0x00000000 +#define TXX9_SILCR_USBL_2BIT 0x00000004 +#define TXX9_SILCR_UMODE_MASK 0x00000003 +#define TXX9_SILCR_UMODE_8BIT 0x00000000 +#define TXX9_SILCR_UMODE_7BIT 0x00000001 + +/* SIDICR : DMA/Int. Control */ +#define TXX9_SIDICR_TDE 0x00008000 +#define TXX9_SIDICR_RDE 0x00004000 +#define TXX9_SIDICR_TIE 0x00002000 +#define TXX9_SIDICR_RIE 0x00001000 +#define TXX9_SIDICR_SPIE 0x00000800 +#define TXX9_SIDICR_CTSAC 0x00000600 +#define TXX9_SIDICR_STIE_MASK 0x0000003f +#define TXX9_SIDICR_STIE_OERS 0x00000020 +#define TXX9_SIDICR_STIE_CTSS 0x00000010 +#define TXX9_SIDICR_STIE_RBRKD 0x00000008 +#define TXX9_SIDICR_STIE_TRDY 0x00000004 +#define TXX9_SIDICR_STIE_TXALS 0x00000002 +#define TXX9_SIDICR_STIE_UBRKD 0x00000001 + +/* SIDISR : DMA/Int. Status */ +#define TXX9_SIDISR_UBRK 0x00008000 +#define TXX9_SIDISR_UVALID 0x00004000 +#define TXX9_SIDISR_UFER 0x00002000 +#define TXX9_SIDISR_UPER 0x00001000 +#define TXX9_SIDISR_UOER 0x00000800 +#define TXX9_SIDISR_ERI 0x00000400 +#define TXX9_SIDISR_TOUT 0x00000200 +#define TXX9_SIDISR_TDIS 0x00000100 +#define TXX9_SIDISR_RDIS 0x00000080 +#define TXX9_SIDISR_STIS 0x00000040 +#define TXX9_SIDISR_RFDN_MASK 0x0000001f + +/* SICISR : Change Int. Status */ +#define TXX9_SICISR_OERS 0x00000020 +#define TXX9_SICISR_CTSS 0x00000010 +#define TXX9_SICISR_RBRKD 0x00000008 +#define TXX9_SICISR_TRDY 0x00000004 +#define TXX9_SICISR_TXALS 0x00000002 +#define TXX9_SICISR_UBRKD 0x00000001 + +/* SIFCR : FIFO Control */ +#define TXX9_SIFCR_SWRST 0x00008000 +#define TXX9_SIFCR_RDIL_MASK 0x00000180 +#define TXX9_SIFCR_RDIL_1 0x00000000 +#define TXX9_SIFCR_RDIL_4 0x00000080 +#define TXX9_SIFCR_RDIL_8 0x00000100 +#define TXX9_SIFCR_RDIL_12 0x00000180 +#define TXX9_SIFCR_RDIL_MAX 0x00000180 +#define TXX9_SIFCR_TDIL_MASK 0x00000018 +#define TXX9_SIFCR_TDIL_MASK 0x00000018 +#define TXX9_SIFCR_TDIL_1 0x00000000 +#define TXX9_SIFCR_TDIL_4 0x00000001 +#define TXX9_SIFCR_TDIL_8 0x00000010 +#define TXX9_SIFCR_TDIL_MAX 0x00000010 +#define TXX9_SIFCR_TFRST 0x00000004 +#define TXX9_SIFCR_RFRST 0x00000002 +#define TXX9_SIFCR_FRSTE 0x00000001 +#define TXX9_SIO_TX_FIFO 8 +#define TXX9_SIO_RX_FIFO 16 + +/* SIFLCR : Flow Control */ +#define TXX9_SIFLCR_RCS 0x00001000 +#define TXX9_SIFLCR_TES 0x00000800 +#define TXX9_SIFLCR_RTSSC 0x00000200 +#define TXX9_SIFLCR_RSDE 0x00000100 +#define TXX9_SIFLCR_TSDE 0x00000080 +#define TXX9_SIFLCR_RTSTL_MASK 0x0000001e +#define TXX9_SIFLCR_RTSTL_MAX 0x0000001e +#define TXX9_SIFLCR_TBRK 0x00000001 + +/* SIBGR : Baudrate Control */ +#define TXX9_SIBGR_BCLK_MASK 0x00000300 +#define TXX9_SIBGR_BCLK_T0 0x00000000 +#define TXX9_SIBGR_BCLK_T2 0x00000100 +#define TXX9_SIBGR_BCLK_T4 0x00000200 +#define TXX9_SIBGR_BCLK_T6 0x00000300 +#define TXX9_SIBGR_BRD_MASK 0x000000ff + +static inline unsigned int sio_in(struct uart_txx9_port *up, int offset) +{ + switch (up->port.iotype) { + default: + return *(volatile u32 *)(up->port.membase + offset); + case UPIO_PORT: + return inl(up->port.iobase + offset); + } +} + +static inline void +sio_out(struct uart_txx9_port *up, int offset, int value) +{ + switch (up->port.iotype) { + default: + *(volatile u32 *)(up->port.membase + offset) = value; + break; + case UPIO_PORT: + outl(value, up->port.iobase + offset); + break; + } +} + +static inline void +sio_mask(struct uart_txx9_port *up, int offset, unsigned int value) +{ + sio_out(up, offset, sio_in(up, offset) & ~value); +} +static inline void +sio_set(struct uart_txx9_port *up, int offset, unsigned int value) +{ + sio_out(up, offset, sio_in(up, offset) | value); +} + +static inline void +sio_quot_set(struct uart_txx9_port *up, int quot) +{ + quot >>= 1; + if (quot < 256) + sio_out(up, TXX9_SIBGR, quot | TXX9_SIBGR_BCLK_T0); + else if (quot < (256 << 2)) + sio_out(up, TXX9_SIBGR, (quot >> 2) | TXX9_SIBGR_BCLK_T2); + else if (quot < (256 << 4)) + sio_out(up, TXX9_SIBGR, (quot >> 4) | TXX9_SIBGR_BCLK_T4); + else if (quot < (256 << 6)) + sio_out(up, TXX9_SIBGR, (quot >> 6) | TXX9_SIBGR_BCLK_T6); + else + sio_out(up, TXX9_SIBGR, 0xff | TXX9_SIBGR_BCLK_T6); +} + +static void serial_txx9_stop_tx(struct uart_port *port, unsigned int tty_stop) +{ + struct uart_txx9_port *up = (struct uart_txx9_port *)port; + unsigned long flags; + + spin_lock_irqsave(&up->port.lock, flags); + sio_mask(up, TXX9_SIDICR, TXX9_SIDICR_TIE); + spin_unlock_irqrestore(&up->port.lock, flags); +} + +static void serial_txx9_start_tx(struct uart_port *port, unsigned int tty_start) +{ + struct uart_txx9_port *up = (struct uart_txx9_port *)port; + unsigned long flags; + + spin_lock_irqsave(&up->port.lock, flags); + sio_set(up, TXX9_SIDICR, TXX9_SIDICR_TIE); + spin_unlock_irqrestore(&up->port.lock, flags); +} + +static void serial_txx9_stop_rx(struct uart_port *port) +{ + struct uart_txx9_port *up = (struct uart_txx9_port *)port; + unsigned long flags; + + spin_lock_irqsave(&up->port.lock, flags); + up->port.read_status_mask &= ~TXX9_SIDISR_RDIS; +#if 0 + sio_mask(up, TXX9_SIDICR, TXX9_SIDICR_RIE); +#endif + spin_unlock_irqrestore(&up->port.lock, flags); +} + +static void serial_txx9_enable_ms(struct uart_port *port) +{ + /* TXX9-SIO can not control DTR... */ +} + +static inline void +receive_chars(struct uart_txx9_port *up, unsigned int *status, struct pt_regs *regs) +{ + struct tty_struct *tty = up->port.info->tty; + unsigned char ch; + unsigned int disr = *status; + int max_count = 256; + char flag; + + do { + /* The following is not allowed by the tty layer and + unsafe. It should be fixed ASAP */ + if (unlikely(tty->flip.count >= TTY_FLIPBUF_SIZE)) { + if(tty->low_latency) + tty_flip_buffer_push(tty); + /* If this failed then we will throw away the + bytes but must do so to clear interrupts */ + } + ch = sio_in(up, TXX9_SIRFIFO); + flag = TTY_NORMAL; + up->port.icount.rx++; + + if (unlikely(disr & (TXX9_SIDISR_UBRK | TXX9_SIDISR_UPER | + TXX9_SIDISR_UFER | TXX9_SIDISR_UOER))) { + /* + * For statistics only + */ + if (disr & TXX9_SIDISR_UBRK) { + disr &= ~(TXX9_SIDISR_UFER | TXX9_SIDISR_UPER); + up->port.icount.brk++; + /* + * We do the SysRQ and SAK checking + * here because otherwise the break + * may get masked by ignore_status_mask + * or read_status_mask. + */ + if (uart_handle_break(&up->port)) + goto ignore_char; + } else if (disr & TXX9_SIDISR_UPER) + up->port.icount.parity++; + else if (disr & TXX9_SIDISR_UFER) + up->port.icount.frame++; + if (disr & TXX9_SIDISR_UOER) + up->port.icount.overrun++; + + /* + * Mask off conditions which should be ingored. + */ + disr &= up->port.read_status_mask; + + if (disr & TXX9_SIDISR_UBRK) { + flag = TTY_BREAK; + } else if (disr & TXX9_SIDISR_UPER) + flag = TTY_PARITY; + else if (disr & TXX9_SIDISR_UFER) + flag = TTY_FRAME; + } + if (uart_handle_sysrq_char(&up->port, ch, regs)) + goto ignore_char; + if ((disr & up->port.ignore_status_mask) == 0) { + tty_insert_flip_char(tty, ch, flag); + } + if ((disr & TXX9_SIDISR_UOER) && + tty->flip.count < TTY_FLIPBUF_SIZE) { + /* + * Overrun is special, since it's reported + * immediately, and doesn't affect the current + * character. + */ + tty_insert_flip_char(tty, 0, TTY_OVERRUN); + } + ignore_char: + disr = sio_in(up, TXX9_SIDISR); + } while (!(disr & TXX9_SIDISR_UVALID) && (max_count-- > 0)); + tty_flip_buffer_push(tty); + *status = disr; +} + +static inline void transmit_chars(struct uart_txx9_port *up) +{ + struct circ_buf *xmit = &up->port.info->xmit; + int count; + + if (up->port.x_char) { + sio_out(up, TXX9_SITFIFO, up->port.x_char); + up->port.icount.tx++; + up->port.x_char = 0; + return; + } + if (uart_circ_empty(xmit) || uart_tx_stopped(&up->port)) { + serial_txx9_stop_tx(&up->port, 0); + return; + } + + count = TXX9_SIO_TX_FIFO; + do { + sio_out(up, TXX9_SITFIFO, xmit->buf[xmit->tail]); + xmit->tail = (xmit->tail + 1) & (UART_XMIT_SIZE - 1); + up->port.icount.tx++; + if (uart_circ_empty(xmit)) + break; + } while (--count > 0); + + if (uart_circ_chars_pending(xmit) < WAKEUP_CHARS) + uart_write_wakeup(&up->port); + + if (uart_circ_empty(xmit)) + serial_txx9_stop_tx(&up->port, 0); +} + +static irqreturn_t serial_txx9_interrupt(int irq, void *dev_id, struct pt_regs *regs) +{ + int pass_counter = 0; + struct uart_txx9_port *up = dev_id; + unsigned int status; + + while (1) { + spin_lock(&up->port.lock); + status = sio_in(up, TXX9_SIDISR); + if (!(sio_in(up, TXX9_SIDICR) & TXX9_SIDICR_TIE)) + status &= ~TXX9_SIDISR_TDIS; + if (!(status & (TXX9_SIDISR_TDIS | TXX9_SIDISR_RDIS | + TXX9_SIDISR_TOUT))) { + spin_unlock(&up->port.lock); + break; + } + + if (status & TXX9_SIDISR_RDIS) + receive_chars(up, &status, regs); + if (status & TXX9_SIDISR_TDIS) + transmit_chars(up); + /* Clear TX/RX Int. Status */ + sio_mask(up, TXX9_SIDISR, + TXX9_SIDISR_TDIS | TXX9_SIDISR_RDIS | + TXX9_SIDISR_TOUT); + spin_unlock(&up->port.lock); + + if (pass_counter++ > PASS_LIMIT) + break; + } + + return pass_counter ? IRQ_HANDLED : IRQ_NONE; +} + +static unsigned int serial_txx9_tx_empty(struct uart_port *port) +{ + struct uart_txx9_port *up = (struct uart_txx9_port *)port; + unsigned long flags; + unsigned int ret; + + spin_lock_irqsave(&up->port.lock, flags); + ret = (sio_in(up, TXX9_SICISR) & TXX9_SICISR_TXALS) ? TIOCSER_TEMT : 0; + spin_unlock_irqrestore(&up->port.lock, flags); + + return ret; +} + +static unsigned int serial_txx9_get_mctrl(struct uart_port *port) +{ + struct uart_txx9_port *up = (struct uart_txx9_port *)port; + unsigned long flags; + unsigned int ret; + + spin_lock_irqsave(&up->port.lock, flags); + ret = ((sio_in(up, TXX9_SIFLCR) & TXX9_SIFLCR_RTSSC) ? 0 : TIOCM_RTS) + | ((sio_in(up, TXX9_SICISR) & TXX9_SICISR_CTSS) ? 0 : TIOCM_CTS); + spin_unlock_irqrestore(&up->port.lock, flags); + + return ret; +} + +static void serial_txx9_set_mctrl(struct uart_port *port, unsigned int mctrl) +{ + struct uart_txx9_port *up = (struct uart_txx9_port *)port; + unsigned long flags; + + spin_lock_irqsave(&up->port.lock, flags); + if (mctrl & TIOCM_RTS) + sio_mask(up, TXX9_SIFLCR, TXX9_SIFLCR_RTSSC); + else + sio_set(up, TXX9_SIFLCR, TXX9_SIFLCR_RTSSC); + spin_unlock_irqrestore(&up->port.lock, flags); +} + +static void serial_txx9_break_ctl(struct uart_port *port, int break_state) +{ + struct uart_txx9_port *up = (struct uart_txx9_port *)port; + unsigned long flags; + + spin_lock_irqsave(&up->port.lock, flags); + if (break_state == -1) + sio_set(up, TXX9_SIFLCR, TXX9_SIFLCR_TBRK); + else + sio_mask(up, TXX9_SIFLCR, TXX9_SIFLCR_TBRK); + spin_unlock_irqrestore(&up->port.lock, flags); +} + +static int serial_txx9_startup(struct uart_port *port) +{ + struct uart_txx9_port *up = (struct uart_txx9_port *)port; + unsigned long flags; + int retval; + + /* + * Clear the FIFO buffers and disable them. + * (they will be reeanbled in set_termios()) + */ + sio_set(up, TXX9_SIFCR, + TXX9_SIFCR_TFRST | TXX9_SIFCR_RFRST | TXX9_SIFCR_FRSTE); + /* clear reset */ + sio_mask(up, TXX9_SIFCR, + TXX9_SIFCR_TFRST | TXX9_SIFCR_RFRST | TXX9_SIFCR_FRSTE); + sio_out(up, TXX9_SIDICR, 0); + + /* + * Clear the interrupt registers. + */ + sio_out(up, TXX9_SIDISR, 0); + + retval = request_irq(up->port.irq, serial_txx9_interrupt, + SA_SHIRQ, "serial_txx9", up); + if (retval) + return retval; + + /* + * Now, initialize the UART + */ + spin_lock_irqsave(&up->port.lock, flags); + serial_txx9_set_mctrl(&up->port, up->port.mctrl); + spin_unlock_irqrestore(&up->port.lock, flags); + + /* Enable RX/TX */ + sio_mask(up, TXX9_SIFLCR, TXX9_SIFLCR_RSDE | TXX9_SIFLCR_TSDE); + + /* + * Finally, enable interrupts. + */ + sio_set(up, TXX9_SIDICR, TXX9_SIDICR_RIE); + + return 0; +} + +static void serial_txx9_shutdown(struct uart_port *port) +{ + struct uart_txx9_port *up = (struct uart_txx9_port *)port; + unsigned long flags; + + /* + * Disable interrupts from this port + */ + sio_out(up, TXX9_SIDICR, 0); /* disable all intrs */ + + spin_lock_irqsave(&up->port.lock, flags); + serial_txx9_set_mctrl(&up->port, up->port.mctrl); + spin_unlock_irqrestore(&up->port.lock, flags); + + /* + * Disable break condition + */ + sio_mask(up, TXX9_SIFLCR, TXX9_SIFLCR_TBRK); + +#ifdef CONFIG_SERIAL_TXX9_CONSOLE + if (up->port.cons && up->port.line == up->port.cons->index) { + free_irq(up->port.irq, up); + return; + } +#endif + /* reset FIFOs */ + sio_set(up, TXX9_SIFCR, + TXX9_SIFCR_TFRST | TXX9_SIFCR_RFRST | TXX9_SIFCR_FRSTE); + /* clear reset */ + sio_mask(up, TXX9_SIFCR, + TXX9_SIFCR_TFRST | TXX9_SIFCR_RFRST | TXX9_SIFCR_FRSTE); + + /* Disable RX/TX */ + sio_set(up, TXX9_SIFLCR, TXX9_SIFLCR_RSDE | TXX9_SIFLCR_TSDE); + + free_irq(up->port.irq, up); +} + +static void +serial_txx9_set_termios(struct uart_port *port, struct termios *termios, + struct termios *old) +{ + struct uart_txx9_port *up = (struct uart_txx9_port *)port; + unsigned int cval, fcr = 0; + unsigned long flags; + unsigned int baud, quot; + + cval = sio_in(up, TXX9_SILCR); + /* byte size and parity */ + cval &= ~TXX9_SILCR_UMODE_MASK; + switch (termios->c_cflag & CSIZE) { + case CS7: + cval |= TXX9_SILCR_UMODE_7BIT; + break; + default: + case CS5: /* not supported */ + case CS6: /* not supported */ + case CS8: + cval |= TXX9_SILCR_UMODE_8BIT; + break; + } + + cval &= ~TXX9_SILCR_USBL_MASK; + if (termios->c_cflag & CSTOPB) + cval |= TXX9_SILCR_USBL_2BIT; + else + cval |= TXX9_SILCR_USBL_1BIT; + cval &= ~(TXX9_SILCR_UPEN | TXX9_SILCR_UEPS); + if (termios->c_cflag & PARENB) + cval |= TXX9_SILCR_UPEN; + if (!(termios->c_cflag & PARODD)) + cval |= TXX9_SILCR_UEPS; + + /* + * Ask the core to calculate the divisor for us. + */ + baud = uart_get_baud_rate(port, termios, old, 0, port->uartclk/16/2); + quot = uart_get_divisor(port, baud); + + /* Set up FIFOs */ + /* TX Int by FIFO Empty, RX Int by Receiving 1 char. */ + fcr = TXX9_SIFCR_TDIL_MAX | TXX9_SIFCR_RDIL_1; + + /* + * Ok, we're now changing the port state. Do it with + * interrupts disabled. + */ + spin_lock_irqsave(&up->port.lock, flags); + + /* + * Update the per-port timeout. + */ + uart_update_timeout(port, termios->c_cflag, baud); + + up->port.read_status_mask = TXX9_SIDISR_UOER | + TXX9_SIDISR_TDIS | TXX9_SIDISR_RDIS; + if (termios->c_iflag & INPCK) + up->port.read_status_mask |= TXX9_SIDISR_UFER | TXX9_SIDISR_UPER; + if (termios->c_iflag & (BRKINT | PARMRK)) + up->port.read_status_mask |= TXX9_SIDISR_UBRK; + + /* + * Characteres to ignore + */ + up->port.ignore_status_mask = 0; + if (termios->c_iflag & IGNPAR) + up->port.ignore_status_mask |= TXX9_SIDISR_UPER | TXX9_SIDISR_UFER; + if (termios->c_iflag & IGNBRK) { + up->port.ignore_status_mask |= TXX9_SIDISR_UBRK; + /* + * If we're ignoring parity and break indicators, + * ignore overruns too (for real raw support). + */ + if (termios->c_iflag & IGNPAR) + up->port.ignore_status_mask |= TXX9_SIDISR_UOER; + } + + /* + * ignore all characters if CREAD is not set + */ + if ((termios->c_cflag & CREAD) == 0) + up->port.ignore_status_mask |= TXX9_SIDISR_RDIS; + + /* CTS flow control flag */ + if ((termios->c_cflag & CRTSCTS) && + (up->port.flags & UPF_TXX9_HAVE_CTS_LINE)) { + sio_set(up, TXX9_SIFLCR, + TXX9_SIFLCR_RCS | TXX9_SIFLCR_TES); + } else { + sio_mask(up, TXX9_SIFLCR, + TXX9_SIFLCR_RCS | TXX9_SIFLCR_TES); + } + + sio_out(up, TXX9_SILCR, cval); + sio_quot_set(up, quot); + sio_out(up, TXX9_SIFCR, fcr); + + serial_txx9_set_mctrl(&up->port, up->port.mctrl); + spin_unlock_irqrestore(&up->port.lock, flags); +} + +static void +serial_txx9_pm(struct uart_port *port, unsigned int state, + unsigned int oldstate) +{ + struct uart_txx9_port *up = (struct uart_txx9_port *)port; + if (state) { + /* sleep */ + + if (up->pm) + up->pm(port, state, oldstate); + } else { + /* wake */ + + if (up->pm) + up->pm(port, state, oldstate); + } +} + +static int serial_txx9_request_resource(struct uart_txx9_port *up) +{ + unsigned int size = TXX9_REGION_SIZE; + int ret = 0; + + switch (up->port.iotype) { + default: + if (!up->port.mapbase) + break; + + if (!request_mem_region(up->port.mapbase, size, "serial_txx9")) { + ret = -EBUSY; + break; + } + + if (up->port.flags & UPF_IOREMAP) { + up->port.membase = ioremap(up->port.mapbase, size); + if (!up->port.membase) { + release_mem_region(up->port.mapbase, size); + ret = -ENOMEM; + } + } + break; + + case UPIO_PORT: + if (!request_region(up->port.iobase, size, "serial_txx9")) + ret = -EBUSY; + break; + } + return ret; +} + +static void serial_txx9_release_resource(struct uart_txx9_port *up) +{ + unsigned int size = TXX9_REGION_SIZE; + + switch (up->port.iotype) { + default: + if (!up->port.mapbase) + break; + + if (up->port.flags & UPF_IOREMAP) { + iounmap(up->port.membase); + up->port.membase = NULL; + } + + release_mem_region(up->port.mapbase, size); + break; + + case UPIO_PORT: + release_region(up->port.iobase, size); + break; + } +} + +static void serial_txx9_release_port(struct uart_port *port) +{ + struct uart_txx9_port *up = (struct uart_txx9_port *)port; + serial_txx9_release_resource(up); +} + +static int serial_txx9_request_port(struct uart_port *port) +{ + struct uart_txx9_port *up = (struct uart_txx9_port *)port; + return serial_txx9_request_resource(up); +} + +static void serial_txx9_config_port(struct uart_port *port, int uflags) +{ + struct uart_txx9_port *up = (struct uart_txx9_port *)port; + unsigned long flags; + int ret; + + /* + * Find the region that we can probe for. This in turn + * tells us whether we can probe for the type of port. + */ + ret = serial_txx9_request_resource(up); + if (ret < 0) + return; + port->type = PORT_TXX9; + up->port.fifosize = TXX9_SIO_TX_FIFO; + +#ifdef CONFIG_SERIAL_TXX9_CONSOLE + if (up->port.line == up->port.cons->index) + return; +#endif + spin_lock_irqsave(&up->port.lock, flags); + /* + * Reset the UART. + */ + sio_out(up, TXX9_SIFCR, TXX9_SIFCR_SWRST); +#ifdef CONFIG_CPU_TX49XX + /* TX4925 BUG WORKAROUND. Accessing SIOC register + * immediately after soft reset causes bus error. */ + iob(); + udelay(1); +#endif + while (sio_in(up, TXX9_SIFCR) & TXX9_SIFCR_SWRST) + ; + /* TX Int by FIFO Empty, RX Int by Receiving 1 char. */ + sio_set(up, TXX9_SIFCR, + TXX9_SIFCR_TDIL_MAX | TXX9_SIFCR_RDIL_1); + /* initial settings */ + sio_out(up, TXX9_SILCR, + TXX9_SILCR_UMODE_8BIT | TXX9_SILCR_USBL_1BIT | + ((up->port.flags & UPF_TXX9_USE_SCLK) ? + TXX9_SILCR_SCS_SCLK_BG : TXX9_SILCR_SCS_IMCLK_BG)); + sio_quot_set(up, uart_get_divisor(port, 9600)); + sio_out(up, TXX9_SIFLCR, TXX9_SIFLCR_RTSTL_MAX /* 15 */); + spin_unlock_irqrestore(&up->port.lock, flags); +} + +static int +serial_txx9_verify_port(struct uart_port *port, struct serial_struct *ser) +{ + if (ser->irq < 0 || + ser->baud_base < 9600 || ser->type != PORT_TXX9) + return -EINVAL; + return 0; +} + +static const char * +serial_txx9_type(struct uart_port *port) +{ + return "txx9"; +} + +static struct uart_ops serial_txx9_pops = { + .tx_empty = serial_txx9_tx_empty, + .set_mctrl = serial_txx9_set_mctrl, + .get_mctrl = serial_txx9_get_mctrl, + .stop_tx = serial_txx9_stop_tx, + .start_tx = serial_txx9_start_tx, + .stop_rx = serial_txx9_stop_rx, + .enable_ms = serial_txx9_enable_ms, + .break_ctl = serial_txx9_break_ctl, + .startup = serial_txx9_startup, + .shutdown = serial_txx9_shutdown, + .set_termios = serial_txx9_set_termios, + .pm = serial_txx9_pm, + .type = serial_txx9_type, + .release_port = serial_txx9_release_port, + .request_port = serial_txx9_request_port, + .config_port = serial_txx9_config_port, + .verify_port = serial_txx9_verify_port, +}; + +static struct uart_txx9_port serial_txx9_ports[UART_NR]; + +static void __init serial_txx9_register_ports(struct uart_driver *drv) +{ + int i; + + for (i = 0; i < UART_NR; i++) { + struct uart_txx9_port *up = &serial_txx9_ports[i]; + + up->port.line = i; + up->port.ops = &serial_txx9_pops; + uart_add_one_port(drv, &up->port); + } +} + +#ifdef CONFIG_SERIAL_TXX9_CONSOLE + +/* + * Wait for transmitter & holding register to empty + */ +static inline void wait_for_xmitr(struct uart_txx9_port *up) +{ + unsigned int tmout = 10000; + + /* Wait up to 10ms for the character(s) to be sent. */ + while (--tmout && + !(sio_in(up, TXX9_SICISR) & TXX9_SICISR_TXALS)) + udelay(1); + + /* Wait up to 1s for flow control if necessary */ + if (up->port.flags & UPF_CONS_FLOW) { + tmout = 1000000; + while (--tmout && + (sio_in(up, TXX9_SICISR) & TXX9_SICISR_CTSS)) + udelay(1); + } +} + +/* + * Print a string to the serial port trying not to disturb + * any possible real use of the port... + * + * The console_lock must be held when we get here. + */ +static void +serial_txx9_console_write(struct console *co, const char *s, unsigned int count) +{ + struct uart_txx9_port *up = &serial_txx9_ports[co->index]; + unsigned int ier, flcr; + int i; + + /* + * First save the UER then disable the interrupts + */ + ier = sio_in(up, TXX9_SIDICR); + sio_out(up, TXX9_SIDICR, 0); + /* + * Disable flow-control if enabled (and unnecessary) + */ + flcr = sio_in(up, TXX9_SIFLCR); + if (!(up->port.flags & UPF_CONS_FLOW) && (flcr & TXX9_SIFLCR_TES)) + sio_out(up, TXX9_SIFLCR, flcr & ~TXX9_SIFLCR_TES); + + /* + * Now, do each character + */ + for (i = 0; i < count; i++, s++) { + wait_for_xmitr(up); + + /* + * Send the character out. + * If a LF, also do CR... + */ + sio_out(up, TXX9_SITFIFO, *s); + if (*s == 10) { + wait_for_xmitr(up); + sio_out(up, TXX9_SITFIFO, 13); + } + } + + /* + * Finally, wait for transmitter to become empty + * and restore the IER + */ + wait_for_xmitr(up); + sio_out(up, TXX9_SIFLCR, flcr); + sio_out(up, TXX9_SIDICR, ier); +} + +static int serial_txx9_console_setup(struct console *co, char *options) +{ + struct uart_port *port; + struct uart_txx9_port *up; + int baud = 9600; + int bits = 8; + int parity = 'n'; + int flow = 'n'; + + /* + * Check whether an invalid uart number has been specified, and + * if so, search for the first available port that does have + * console support. + */ + if (co->index >= UART_NR) + co->index = 0; + up = &serial_txx9_ports[co->index]; + port = &up->port; + if (!port->ops) + return -ENODEV; + + /* + * Temporary fix. + */ + spin_lock_init(&port->lock); + + /* + * Disable UART interrupts, set DTR and RTS high + * and set speed. + */ + sio_out(up, TXX9_SIDICR, 0); + /* initial settings */ + sio_out(up, TXX9_SILCR, + TXX9_SILCR_UMODE_8BIT | TXX9_SILCR_USBL_1BIT | + ((port->flags & UPF_TXX9_USE_SCLK) ? + TXX9_SILCR_SCS_SCLK_BG : TXX9_SILCR_SCS_IMCLK_BG)); + sio_out(up, TXX9_SIFLCR, TXX9_SIFLCR_RTSTL_MAX /* 15 */); + + if (options) + uart_parse_options(options, &baud, &parity, &bits, &flow); + + return uart_set_options(port, co, baud, parity, bits, flow); +} + +static struct uart_driver serial_txx9_reg; +static struct console serial_txx9_console = { + .name = TXX9_TTY_NAME, + .write = serial_txx9_console_write, + .device = uart_console_device, + .setup = serial_txx9_console_setup, + .flags = CON_PRINTBUFFER, + .index = -1, + .data = &serial_txx9_reg, +}; + +static int __init serial_txx9_console_init(void) +{ + register_console(&serial_txx9_console); + return 0; +} +console_initcall(serial_txx9_console_init); + +static int __init serial_txx9_late_console_init(void) +{ + if (!(serial_txx9_console.flags & CON_ENABLED)) + register_console(&serial_txx9_console); + return 0; +} +late_initcall(serial_txx9_late_console_init); + +#define SERIAL_TXX9_CONSOLE &serial_txx9_console +#else +#define SERIAL_TXX9_CONSOLE NULL +#endif + +static struct uart_driver serial_txx9_reg = { + .owner = THIS_MODULE, + .driver_name = "serial_txx9", + .devfs_name = TXX9_TTY_DEVFS_NAME, + .dev_name = TXX9_TTY_NAME, + .major = TXX9_TTY_MAJOR, + .minor = TXX9_TTY_MINOR_START, + .nr = UART_NR, + .cons = SERIAL_TXX9_CONSOLE, +}; + +int __init early_serial_txx9_setup(struct uart_port *port) +{ + if (port->line >= ARRAY_SIZE(serial_txx9_ports)) + return -ENODEV; + + serial_txx9_ports[port->line].port = *port; + serial_txx9_ports[port->line].port.ops = &serial_txx9_pops; + serial_txx9_ports[port->line].port.flags |= UPF_BOOT_AUTOCONF; + return 0; +} + +#ifdef ENABLE_SERIAL_TXX9_PCI +/** + * serial_txx9_suspend_port - suspend one serial port + * @line: serial line number + * @level: the level of port suspension, as per uart_suspend_port + * + * Suspend one serial port. + */ +static void serial_txx9_suspend_port(int line) +{ + uart_suspend_port(&serial_txx9_reg, &serial_txx9_ports[line].port); +} + +/** + * serial_txx9_resume_port - resume one serial port + * @line: serial line number + * @level: the level of port resumption, as per uart_resume_port + * + * Resume one serial port. + */ +static void serial_txx9_resume_port(int line) +{ + uart_resume_port(&serial_txx9_reg, &serial_txx9_ports[line].port); +} + +/* + * Probe one serial board. Unfortunately, there is no rhyme nor reason + * to the arrangement of serial ports on a PCI card. + */ +static int __devinit +pciserial_txx9_init_one(struct pci_dev *dev, const struct pci_device_id *ent) +{ + struct uart_port port; + int line; + int rc; + + rc = pci_enable_device(dev); + if (rc) + return rc; + + memset(&port, 0, sizeof(port)); + port.ops = &serial_txx9_pops; + port.flags |= UPF_BOOT_AUTOCONF; /* uart_ops.config_port will be called */ + port.flags |= UPF_TXX9_HAVE_CTS_LINE; + port.uartclk = 66670000; + port.irq = dev->irq; + port.iotype = UPIO_PORT; + port.iobase = pci_resource_start(dev, 1); + line = uart_register_port(&serial_txx9_reg, &port); + if (line < 0) { + printk(KERN_WARNING "Couldn't register serial port %s: %d\n", pci_name(dev), line); + } + pci_set_drvdata(dev, (void *)(long)line); + + return 0; +} + +static void __devexit pciserial_txx9_remove_one(struct pci_dev *dev) +{ + int line = (int)(long)pci_get_drvdata(dev); + + pci_set_drvdata(dev, NULL); + + if (line) { + uart_unregister_port(&serial_txx9_reg, line); + pci_disable_device(dev); + } +} + +static int pciserial_txx9_suspend_one(struct pci_dev *dev, u32 state) +{ + int line = (int)(long)pci_get_drvdata(dev); + + if (line) + serial_txx9_suspend_port(line); + return 0; +} + +static int pciserial_txx9_resume_one(struct pci_dev *dev) +{ + int line = (int)(long)pci_get_drvdata(dev); + + if (line) + serial_txx9_resume_port(line); + return 0; +} + +static struct pci_device_id serial_txx9_pci_tbl[] = { + { PCI_VENDOR_ID_TOSHIBA_2, PCI_DEVICE_ID_TOSHIBA_TC86C001_MISC, + PCI_ANY_ID, PCI_ANY_ID, + 0, 0, 0 }, + { 0, } +}; + +static struct pci_driver serial_txx9_pci_driver = { + .name = "serial_txx9", + .probe = pciserial_txx9_init_one, + .remove = __devexit_p(pciserial_txx9_remove_one), + .suspend = pciserial_txx9_suspend_one, + .resume = pciserial_txx9_resume_one, + .id_table = serial_txx9_pci_tbl, +}; + +MODULE_DEVICE_TABLE(pci, serial_txx9_pci_tbl); +#endif /* ENABLE_SERIAL_TXX9_PCI */ + +static int __init serial_txx9_init(void) +{ + int ret; + + printk(KERN_INFO "%s version %s\n", serial_name, serial_version); + + ret = uart_register_driver(&serial_txx9_reg); + if (ret >= 0) { + serial_txx9_register_ports(&serial_txx9_reg); + +#ifdef ENABLE_SERIAL_TXX9_PCI + ret = pci_module_init(&serial_txx9_pci_driver); +#endif + } + return ret; +} + +static void __exit serial_txx9_exit(void) +{ + int i; + +#ifdef ENABLE_SERIAL_TXX9_PCI + pci_unregister_driver(&serial_txx9_pci_driver); +#endif + for (i = 0; i < UART_NR; i++) + uart_remove_one_port(&serial_txx9_reg, &serial_txx9_ports[i].port); + + uart_unregister_driver(&serial_txx9_reg); +} + +module_init(serial_txx9_init); +module_exit(serial_txx9_exit); + +MODULE_LICENSE("GPL"); +MODULE_DESCRIPTION("TX39/49 serial driver"); + +MODULE_ALIAS_CHARDEV_MAJOR(TXX9_TTY_MAJOR); |