diff options
Diffstat (limited to 'drivers/staging')
-rw-r--r-- | drivers/staging/winbond/bssdscpt.h | 2 | ||||
-rw-r--r-- | drivers/staging/winbond/linux/common.h | 19 | ||||
-rw-r--r-- | drivers/staging/winbond/mds_f.h | 6 | ||||
-rw-r--r-- | drivers/staging/winbond/mds_s.h | 3 | ||||
-rw-r--r-- | drivers/staging/winbond/rxisr.c | 29 | ||||
-rw-r--r-- | drivers/staging/winbond/scan_s.h | 3 | ||||
-rw-r--r-- | drivers/staging/winbond/sme_s.h | 3 | ||||
-rw-r--r-- | drivers/staging/winbond/wbhal.c | 586 | ||||
-rw-r--r-- | drivers/staging/winbond/wbhal_f.h | 2 | ||||
-rw-r--r-- | drivers/staging/winbond/wbhal_s.h | 2 |
10 files changed, 312 insertions, 343 deletions
diff --git a/drivers/staging/winbond/bssdscpt.h b/drivers/staging/winbond/bssdscpt.h index 6f557cbb..90b5682 100644 --- a/drivers/staging/winbond/bssdscpt.h +++ b/drivers/staging/winbond/bssdscpt.h @@ -79,7 +79,7 @@ typedef struct BSSDescriptionElement u16 wIndex; // THIS BSS element entry index void* psadapter; // pointer to THIS adapter - OS_TIMER nTimer; // MLME timer + struct timer_list timer; // MLME timer // Authentication u16 wAuthAlgo; // peer MAC MLME use Auth algorithm, default OPEN_AUTH diff --git a/drivers/staging/winbond/linux/common.h b/drivers/staging/winbond/linux/common.h index 42c23a8..521b68a 100644 --- a/drivers/staging/winbond/linux/common.h +++ b/drivers/staging/winbond/linux/common.h @@ -84,24 +84,5 @@ #define OS_MEMORY_CLEAR( _A, _S ) memset( (u8 *)_A,0,_S) #define OS_MEMORY_COMPARE( _A, _B, _S ) (memcmp(_A,_B,_S)? 0 : 1) // Definition is reverse with Ndis 1: the same 0: different -#define OS_TIMER struct timer_list -#define OS_TIMER_INITIAL( _T, _F, _P ) \ -{ \ - init_timer( _T ); \ - (_T)->function = (void *)_F##_1a; \ - (_T)->data = (unsigned long)_P; \ -} - -// _S : Millisecond -// 20060420 At least 1 large than jiffies -#define OS_TIMER_SET( _T, _S ) \ -{ \ - (_T)->expires = jiffies + ((_S*HZ+999)/1000);\ - add_timer( _T ); \ -} -#define OS_TIMER_CANCEL( _T, _B ) del_timer_sync( _T ) -#define OS_TIMER_GET_SYS_TIME( _T ) (*_T=jiffies) - - #endif // COMMON_DEF diff --git a/drivers/staging/winbond/mds_f.h b/drivers/staging/winbond/mds_f.h index 0733b9f..4258b32 100644 --- a/drivers/staging/winbond/mds_f.h +++ b/drivers/staging/winbond/mds_f.h @@ -12,13 +12,7 @@ extern void DataDmp(u8 *pdata, u32 len, u32 offset); void vRxTimerInit(struct wb35_adapter *adapter); void vRxTimerStart(struct wb35_adapter *adapter, int timeout_value); -void RxTimerHandler_1a( struct wb35_adapter *adapter); void vRxTimerStop(struct wb35_adapter *adapter); -void RxTimerHandler( void* SystemSpecific1, - struct wb35_adapter * adapter, - void* SystemSpecific2, - void* SystemSpecific3); - // For Asynchronous indicating. The routine collocates with USB. void Mds_MsduProcess( struct wb35_adapter *adapter, PRXLAYER1 pRxLayer1, u8 SlotIndex); diff --git a/drivers/staging/winbond/mds_s.h b/drivers/staging/winbond/mds_s.h index 283945c..ac1875f 100644 --- a/drivers/staging/winbond/mds_s.h +++ b/drivers/staging/winbond/mds_s.h @@ -133,8 +133,7 @@ typedef struct _MDS u8 boCounterMeasureBlock; u8 reserved_4[2]; - //NDIS_MINIPORT_TIMER nTimer; - OS_TIMER nTimer; + struct timer_list timer; u32 TxTsc; // 20060214 u32 TxTsc_2; // 20060214 diff --git a/drivers/staging/winbond/rxisr.c b/drivers/staging/winbond/rxisr.c index 6678660..de49a49 100644 --- a/drivers/staging/winbond/rxisr.c +++ b/drivers/staging/winbond/rxisr.c @@ -1,30 +1,27 @@ #include "os_common.h" -void vRxTimerInit(struct wb35_adapter * adapter) +static void RxTimerHandler(unsigned long data) { - OS_TIMER_INITIAL(&(adapter->Mds.nTimer), (void*) RxTimerHandler, (void*) adapter); + WARN_ON(1); } -void vRxTimerStart(struct wb35_adapter * adapter, int timeout_value) +void vRxTimerInit(struct wb35_adapter *adapter) { - if (timeout_value<MIN_TIMEOUT_VAL) - timeout_value=MIN_TIMEOUT_VAL; - - OS_TIMER_SET( &(adapter->Mds.nTimer), timeout_value ); + init_timer(&adapter->Mds.timer); + adapter->Mds.timer.function = RxTimerHandler; + adapter->Mds.timer.data = (unsigned long) adapter; } -void vRxTimerStop(struct wb35_adapter * adapter) +void vRxTimerStart(struct wb35_adapter *adapter, int timeout_value) { - OS_TIMER_CANCEL( &(adapter->Mds.nTimer), 0 ); -} + if (timeout_value < MIN_TIMEOUT_VAL) + timeout_value = MIN_TIMEOUT_VAL; -void RxTimerHandler_1a( struct wb35_adapter * adapter) -{ - RxTimerHandler(NULL, adapter, NULL, NULL); + adapter->Mds.timer.expires = jiffies + msecs_to_jiffies(timeout_value); + add_timer(&adapter->Mds.timer); } -void RxTimerHandler(void* SystemSpecific1, struct wb35_adapter * adapter, - void* SystemSpecific2, void* SystemSpecific3) +void vRxTimerStop(struct wb35_adapter *adapter) { - WARN_ON(1); + del_timer_sync(&adapter->Mds.timer); } diff --git a/drivers/staging/winbond/scan_s.h b/drivers/staging/winbond/scan_s.h index a7489cb..a952396 100644 --- a/drivers/staging/winbond/scan_s.h +++ b/drivers/staging/winbond/scan_s.h @@ -62,8 +62,7 @@ typedef struct _SCAN_PARAMETERS u8 boCCAbusy; // Wb: HWMAC CCA busy status u8 reserved_2; - //NDIS_MINIPORT_TIMER nTimer; - OS_TIMER nTimer; + struct timer_list timer; u32 ScanTimeStamp; //Increase 1 per background scan(1 minute) u32 BssTimeStamp; //Increase 1 per connect status check diff --git a/drivers/staging/winbond/sme_s.h b/drivers/staging/winbond/sme_s.h index de4efa1..33f5d2a 100644 --- a/drivers/staging/winbond/sme_s.h +++ b/drivers/staging/winbond/sme_s.h @@ -106,8 +106,7 @@ typedef struct _SME_PARAMETERS u8 bDesiredPowerSave; // SME timer and timeout value - //NDIS_MINIPORT_TIMER nTimer; - OS_TIMER nTimer; + struct timer_list timer; u8 boInTimerHandler; u8 boAuthRetryActive; diff --git a/drivers/staging/winbond/wbhal.c b/drivers/staging/winbond/wbhal.c index 69dcedf..3edcc47 100644 --- a/drivers/staging/winbond/wbhal.c +++ b/drivers/staging/winbond/wbhal.c @@ -28,6 +28,292 @@ void hal_get_permanent_address( phw_data_t pHwData, u8 *pethernet_address ) memcpy( pethernet_address, pHwData->PermanentMacAddress, 6 ); } +static void hal_led_control(unsigned long data) +{ + phw_data_t pHwData = (phw_data_t) data; + struct wb35_adapter * adapter = pHwData->adapter; + struct wb35_reg *reg = &pHwData->reg; + u32 LEDSet = (pHwData->SoftwareSet & HAL_LED_SET_MASK) >> HAL_LED_SET_SHIFT; + u8 LEDgray[20] = { 0,3,4,6,8,10,11,12,13,14,15,14,13,12,11,10,8,6,4,2 }; + u8 LEDgray2[30] = { 7,8,9,10,11,12,13,14,15,0,0,0,0,0,0,0,0,0,0,0,0,0,15,14,13,12,11,10,9,8 }; + u32 TimeInterval = 500, ltmp, ltmp2; + ltmp=0; + + if( pHwData->SurpriseRemove ) return; + + if( pHwData->LED_control ) { + ltmp2 = pHwData->LED_control & 0xff; + if( ltmp2 == 5 ) // 5 is WPS mode + { + TimeInterval = 100; + ltmp2 = (pHwData->LED_control>>8) & 0xff; + switch( ltmp2 ) + { + case 1: // [0.2 On][0.1 Off]... + pHwData->LED_Blinking %= 3; + ltmp = 0x1010; // Led 1 & 0 Green and Red + if( pHwData->LED_Blinking == 2 ) // Turn off + ltmp = 0; + break; + case 2: // [0.1 On][0.1 Off]... + pHwData->LED_Blinking %= 2; + ltmp = 0x0010; // Led 0 red color + if( pHwData->LED_Blinking ) // Turn off + ltmp = 0; + break; + case 3: // [0.1 On][0.1 Off][0.1 On][0.1 Off][0.1 On][0.1 Off][0.1 On][0.1 Off][0.1 On][0.1 Off][0.5 Off]... + pHwData->LED_Blinking %= 15; + ltmp = 0x0010; // Led 0 red color + if( (pHwData->LED_Blinking >= 9) || (pHwData->LED_Blinking%2) ) // Turn off 0.6 sec + ltmp = 0; + break; + case 4: // [300 On][ off ] + ltmp = 0x1000; // Led 1 Green color + if( pHwData->LED_Blinking >= 3000 ) + ltmp = 0; // led maybe on after 300sec * 32bit counter overlap. + break; + } + pHwData->LED_Blinking++; + + reg->U1BC_LEDConfigure = ltmp; + if( LEDSet != 7 ) // Only 111 mode has 2 LEDs on PCB. + { + reg->U1BC_LEDConfigure |= (ltmp &0xff)<<8; // Copy LED result to each LED control register + reg->U1BC_LEDConfigure |= (ltmp &0xff00)>>8; + } + Wb35Reg_Write( pHwData, 0x03bc, reg->U1BC_LEDConfigure ); + } + } + else if( pHwData->CurrentRadioSw || pHwData->CurrentRadioHw ) // If radio off + { + if( reg->U1BC_LEDConfigure & 0x1010 ) + { + reg->U1BC_LEDConfigure &= ~0x1010; + Wb35Reg_Write( pHwData, 0x03bc, reg->U1BC_LEDConfigure ); + } + } + else + { + switch( LEDSet ) + { + case 4: // [100] Only 1 Led be placed on PCB and use pin 21 of IC. Use LED_0 for showing + if( !pHwData->LED_LinkOn ) // Blink only if not Link On + { + // Blinking if scanning is on progress + if( pHwData->LED_Scanning ) + { + if( pHwData->LED_Blinking == 0 ) + { + reg->U1BC_LEDConfigure |= 0x10; + Wb35Reg_Write( pHwData, 0x03bc, reg->U1BC_LEDConfigure ); // LED_0 On + pHwData->LED_Blinking = 1; + TimeInterval = 300; + } + else + { + reg->U1BC_LEDConfigure &= ~0x10; + Wb35Reg_Write( pHwData, 0x03bc, reg->U1BC_LEDConfigure ); // LED_0 Off + pHwData->LED_Blinking = 0; + TimeInterval = 300; + } + } + else + { + //Turn Off LED_0 + if( reg->U1BC_LEDConfigure & 0x10 ) + { + reg->U1BC_LEDConfigure &= ~0x10; + Wb35Reg_Write( pHwData, 0x03bc, reg->U1BC_LEDConfigure ); // LED_0 Off + } + } + } + else + { + // Turn On LED_0 + if( (reg->U1BC_LEDConfigure & 0x10) == 0 ) + { + reg->U1BC_LEDConfigure |= 0x10; + Wb35Reg_Write( pHwData, 0x03bc, reg->U1BC_LEDConfigure ); // LED_0 Off + } + } + break; + + case 6: // [110] Only 1 Led be placed on PCB and use pin 21 of IC. Use LED_0 for showing + if( !pHwData->LED_LinkOn ) // Blink only if not Link On + { + // Blinking if scanning is on progress + if( pHwData->LED_Scanning ) + { + if( pHwData->LED_Blinking == 0 ) + { + reg->U1BC_LEDConfigure &= ~0xf; + reg->U1BC_LEDConfigure |= 0x10; + Wb35Reg_Write( pHwData, 0x03bc, reg->U1BC_LEDConfigure ); // LED_0 On + pHwData->LED_Blinking = 1; + TimeInterval = 300; + } + else + { + reg->U1BC_LEDConfigure &= ~0x1f; + Wb35Reg_Write( pHwData, 0x03bc, reg->U1BC_LEDConfigure ); // LED_0 Off + pHwData->LED_Blinking = 0; + TimeInterval = 300; + } + } + else + { + // 20060901 Gray blinking if in disconnect state and not scanning + ltmp = reg->U1BC_LEDConfigure; + reg->U1BC_LEDConfigure &= ~0x1f; + if( LEDgray2[(pHwData->LED_Blinking%30)] ) + { + reg->U1BC_LEDConfigure |= 0x10; + reg->U1BC_LEDConfigure |= LEDgray2[ (pHwData->LED_Blinking%30) ]; + } + pHwData->LED_Blinking++; + if( reg->U1BC_LEDConfigure != ltmp ) + Wb35Reg_Write( pHwData, 0x03bc, reg->U1BC_LEDConfigure ); // LED_0 Off + TimeInterval = 100; + } + } + else + { + // Turn On LED_0 + if( (reg->U1BC_LEDConfigure & 0x10) == 0 ) + { + reg->U1BC_LEDConfigure |= 0x10; + Wb35Reg_Write( pHwData, 0x03bc, reg->U1BC_LEDConfigure ); // LED_0 Off + } + } + break; + + case 5: // [101] Only 1 Led be placed on PCB and use LED_1 for showing + if( !pHwData->LED_LinkOn ) // Blink only if not Link On + { + // Blinking if scanning is on progress + if( pHwData->LED_Scanning ) + { + if( pHwData->LED_Blinking == 0 ) + { + reg->U1BC_LEDConfigure |= 0x1000; + Wb35Reg_Write( pHwData, 0x03bc, reg->U1BC_LEDConfigure ); // LED_1 On + pHwData->LED_Blinking = 1; + TimeInterval = 300; + } + else + { + reg->U1BC_LEDConfigure &= ~0x1000; + Wb35Reg_Write( pHwData, 0x03bc, reg->U1BC_LEDConfigure ); // LED_1 Off + pHwData->LED_Blinking = 0; + TimeInterval = 300; + } + } + else + { + //Turn Off LED_1 + if( reg->U1BC_LEDConfigure & 0x1000 ) + { + reg->U1BC_LEDConfigure &= ~0x1000; + Wb35Reg_Write( pHwData, 0x03bc, reg->U1BC_LEDConfigure ); // LED_1 Off + } + } + } + else + { + // Is transmitting/receiving ?? + if( (OS_CURRENT_RX_BYTE( adapter ) != pHwData->RxByteCountLast ) || + (OS_CURRENT_TX_BYTE( adapter ) != pHwData->TxByteCountLast ) ) + { + if( (reg->U1BC_LEDConfigure & 0x3000) != 0x3000 ) + { + reg->U1BC_LEDConfigure |= 0x3000; + Wb35Reg_Write( pHwData, 0x03bc, reg->U1BC_LEDConfigure ); // LED_1 On + } + + // Update variable + pHwData->RxByteCountLast = OS_CURRENT_RX_BYTE( adapter ); + pHwData->TxByteCountLast = OS_CURRENT_TX_BYTE( adapter ); + TimeInterval = 200; + } + else + { + // Turn On LED_1 and blinking if transmitting/receiving + if( (reg->U1BC_LEDConfigure & 0x3000) != 0x1000 ) + { + reg->U1BC_LEDConfigure &= ~0x3000; + reg->U1BC_LEDConfigure |= 0x1000; + Wb35Reg_Write( pHwData, 0x03bc, reg->U1BC_LEDConfigure ); // LED_1 On + } + } + } + break; + + default: // Default setting. 2 LED be placed on PCB. LED_0: Link On LED_1 Active + if( (reg->U1BC_LEDConfigure & 0x3000) != 0x3000 ) + { + reg->U1BC_LEDConfigure |= 0x3000;// LED_1 is always on and event enable + Wb35Reg_Write( pHwData, 0x03bc, reg->U1BC_LEDConfigure ); + } + + if( pHwData->LED_Blinking ) + { + // Gray blinking + reg->U1BC_LEDConfigure &= ~0x0f; + reg->U1BC_LEDConfigure |= 0x10; + reg->U1BC_LEDConfigure |= LEDgray[ (pHwData->LED_Blinking-1)%20 ]; + Wb35Reg_Write( pHwData, 0x03bc, reg->U1BC_LEDConfigure ); + + pHwData->LED_Blinking += 2; + if( pHwData->LED_Blinking < 40 ) + TimeInterval = 100; + else + { + pHwData->LED_Blinking = 0; // Stop blinking + reg->U1BC_LEDConfigure &= ~0x0f; + Wb35Reg_Write( pHwData, 0x03bc, reg->U1BC_LEDConfigure ); + } + break; + } + + if( pHwData->LED_LinkOn ) + { + if( !(reg->U1BC_LEDConfigure & 0x10) ) // Check the LED_0 + { + //Try to turn ON LED_0 after gray blinking + reg->U1BC_LEDConfigure |= 0x10; + pHwData->LED_Blinking = 1; //Start blinking + TimeInterval = 50; + } + } + else + { + if( reg->U1BC_LEDConfigure & 0x10 ) // Check the LED_0 + { + reg->U1BC_LEDConfigure &= ~0x10; + Wb35Reg_Write( pHwData, 0x03bc, reg->U1BC_LEDConfigure ); + } + } + break; + } + + //20060828.1 Active send null packet to avoid AP disconnect + if( pHwData->LED_LinkOn ) + { + pHwData->NullPacketCount += TimeInterval; + if( pHwData->NullPacketCount >= DEFAULT_NULL_PACKET_COUNT ) + { + pHwData->NullPacketCount = 0; + } + } + } + + pHwData->time_count += TimeInterval; + Wb35Tx_CurrentTime( pHwData, pHwData->time_count ); // 20060928 add + pHwData->LEDTimer.expires = jiffies + msecs_to_jiffies(TimeInterval); + add_timer(&pHwData->LEDTimer); +} + + u8 hal_init_hardware(phw_data_t pHwData, struct wb35_adapter * adapter) { u16 SoftwareSet; @@ -44,8 +330,11 @@ u8 hal_init_hardware(phw_data_t pHwData, struct wb35_adapter * adapter) pHwData->InitialResource = 3; if (Wb35Rx_initial(pHwData)) { pHwData->InitialResource = 4; - OS_TIMER_INITIAL( &pHwData->LEDTimer, hal_led_control, pHwData ); - OS_TIMER_SET( &pHwData->LEDTimer, 1000 ); // 20060623 + init_timer(&pHwData->LEDTimer); + pHwData->LEDTimer.function = hal_led_control; + pHwData->LEDTimer.data = (unsigned long) pHwData; + pHwData->LEDTimer.expires = jiffies + msecs_to_jiffies(1000); + add_timer(&pHwData->LEDTimer); // // For restrict to vendor's hardware @@ -77,7 +366,7 @@ void hal_halt(phw_data_t pHwData, void *ppa_data) switch( pHwData->InitialResource ) { case 4: - case 3: OS_TIMER_CANCEL( &pHwData->LEDTimer, &cancel ); + case 3: del_timer_sync(&pHwData->LEDTimer); msleep(100); // Wait for Timer DPC exit 940623.2 Wb35Rx_destroy( pHwData ); // Release the Rx case 2: Wb35Tx_destroy( pHwData ); // Release the Tx @@ -431,294 +720,6 @@ s32 hal_get_rssi_bss( phw_data_t pHwData, u16 idx, u8 Count ) } //--------------------------------------------------------------------------- -void hal_led_control_1a( phw_data_t pHwData ) -{ - hal_led_control( NULL, pHwData, NULL, NULL ); -} - -void hal_led_control( void* S1, phw_data_t pHwData, void* S3, void* S4 ) -{ - struct wb35_adapter * adapter = pHwData->adapter; - struct wb35_reg *reg = &pHwData->reg; - u32 LEDSet = (pHwData->SoftwareSet & HAL_LED_SET_MASK) >> HAL_LED_SET_SHIFT; - u8 LEDgray[20] = { 0,3,4,6,8,10,11,12,13,14,15,14,13,12,11,10,8,6,4,2 }; - u8 LEDgray2[30] = { 7,8,9,10,11,12,13,14,15,0,0,0,0,0,0,0,0,0,0,0,0,0,15,14,13,12,11,10,9,8 }; - u32 TimeInterval = 500, ltmp, ltmp2; - ltmp=0; - - if( pHwData->SurpriseRemove ) return; - - if( pHwData->LED_control ) { - ltmp2 = pHwData->LED_control & 0xff; - if( ltmp2 == 5 ) // 5 is WPS mode - { - TimeInterval = 100; - ltmp2 = (pHwData->LED_control>>8) & 0xff; - switch( ltmp2 ) - { - case 1: // [0.2 On][0.1 Off]... - pHwData->LED_Blinking %= 3; - ltmp = 0x1010; // Led 1 & 0 Green and Red - if( pHwData->LED_Blinking == 2 ) // Turn off - ltmp = 0; - break; - case 2: // [0.1 On][0.1 Off]... - pHwData->LED_Blinking %= 2; - ltmp = 0x0010; // Led 0 red color - if( pHwData->LED_Blinking ) // Turn off - ltmp = 0; - break; - case 3: // [0.1 On][0.1 Off][0.1 On][0.1 Off][0.1 On][0.1 Off][0.1 On][0.1 Off][0.1 On][0.1 Off][0.5 Off]... - pHwData->LED_Blinking %= 15; - ltmp = 0x0010; // Led 0 red color - if( (pHwData->LED_Blinking >= 9) || (pHwData->LED_Blinking%2) ) // Turn off 0.6 sec - ltmp = 0; - break; - case 4: // [300 On][ off ] - ltmp = 0x1000; // Led 1 Green color - if( pHwData->LED_Blinking >= 3000 ) - ltmp = 0; // led maybe on after 300sec * 32bit counter overlap. - break; - } - pHwData->LED_Blinking++; - - reg->U1BC_LEDConfigure = ltmp; - if( LEDSet != 7 ) // Only 111 mode has 2 LEDs on PCB. - { - reg->U1BC_LEDConfigure |= (ltmp &0xff)<<8; // Copy LED result to each LED control register - reg->U1BC_LEDConfigure |= (ltmp &0xff00)>>8; - } - Wb35Reg_Write( pHwData, 0x03bc, reg->U1BC_LEDConfigure ); - } - } - else if( pHwData->CurrentRadioSw || pHwData->CurrentRadioHw ) // If radio off - { - if( reg->U1BC_LEDConfigure & 0x1010 ) - { - reg->U1BC_LEDConfigure &= ~0x1010; - Wb35Reg_Write( pHwData, 0x03bc, reg->U1BC_LEDConfigure ); - } - } - else - { - switch( LEDSet ) - { - case 4: // [100] Only 1 Led be placed on PCB and use pin 21 of IC. Use LED_0 for showing - if( !pHwData->LED_LinkOn ) // Blink only if not Link On - { - // Blinking if scanning is on progress - if( pHwData->LED_Scanning ) - { - if( pHwData->LED_Blinking == 0 ) - { - reg->U1BC_LEDConfigure |= 0x10; - Wb35Reg_Write( pHwData, 0x03bc, reg->U1BC_LEDConfigure ); // LED_0 On - pHwData->LED_Blinking = 1; - TimeInterval = 300; - } - else - { - reg->U1BC_LEDConfigure &= ~0x10; - Wb35Reg_Write( pHwData, 0x03bc, reg->U1BC_LEDConfigure ); // LED_0 Off - pHwData->LED_Blinking = 0; - TimeInterval = 300; - } - } - else - { - //Turn Off LED_0 - if( reg->U1BC_LEDConfigure & 0x10 ) - { - reg->U1BC_LEDConfigure &= ~0x10; - Wb35Reg_Write( pHwData, 0x03bc, reg->U1BC_LEDConfigure ); // LED_0 Off - } - } - } - else - { - // Turn On LED_0 - if( (reg->U1BC_LEDConfigure & 0x10) == 0 ) - { - reg->U1BC_LEDConfigure |= 0x10; - Wb35Reg_Write( pHwData, 0x03bc, reg->U1BC_LEDConfigure ); // LED_0 Off - } - } - break; - - case 6: // [110] Only 1 Led be placed on PCB and use pin 21 of IC. Use LED_0 for showing - if( !pHwData->LED_LinkOn ) // Blink only if not Link On - { - // Blinking if scanning is on progress - if( pHwData->LED_Scanning ) - { - if( pHwData->LED_Blinking == 0 ) - { - reg->U1BC_LEDConfigure &= ~0xf; - reg->U1BC_LEDConfigure |= 0x10; - Wb35Reg_Write( pHwData, 0x03bc, reg->U1BC_LEDConfigure ); // LED_0 On - pHwData->LED_Blinking = 1; - TimeInterval = 300; - } - else - { - reg->U1BC_LEDConfigure &= ~0x1f; - Wb35Reg_Write( pHwData, 0x03bc, reg->U1BC_LEDConfigure ); // LED_0 Off - pHwData->LED_Blinking = 0; - TimeInterval = 300; - } - } - else - { - // 20060901 Gray blinking if in disconnect state and not scanning - ltmp = reg->U1BC_LEDConfigure; - reg->U1BC_LEDConfigure &= ~0x1f; - if( LEDgray2[(pHwData->LED_Blinking%30)] ) - { - reg->U1BC_LEDConfigure |= 0x10; - reg->U1BC_LEDConfigure |= LEDgray2[ (pHwData->LED_Blinking%30) ]; - } - pHwData->LED_Blinking++; - if( reg->U1BC_LEDConfigure != ltmp ) - Wb35Reg_Write( pHwData, 0x03bc, reg->U1BC_LEDConfigure ); // LED_0 Off - TimeInterval = 100; - } - } - else - { - // Turn On LED_0 - if( (reg->U1BC_LEDConfigure & 0x10) == 0 ) - { - reg->U1BC_LEDConfigure |= 0x10; - Wb35Reg_Write( pHwData, 0x03bc, reg->U1BC_LEDConfigure ); // LED_0 Off - } - } - break; - - case 5: // [101] Only 1 Led be placed on PCB and use LED_1 for showing - if( !pHwData->LED_LinkOn ) // Blink only if not Link On - { - // Blinking if scanning is on progress - if( pHwData->LED_Scanning ) - { - if( pHwData->LED_Blinking == 0 ) - { - reg->U1BC_LEDConfigure |= 0x1000; - Wb35Reg_Write( pHwData, 0x03bc, reg->U1BC_LEDConfigure ); // LED_1 On - pHwData->LED_Blinking = 1; - TimeInterval = 300; - } - else - { - reg->U1BC_LEDConfigure &= ~0x1000; - Wb35Reg_Write( pHwData, 0x03bc, reg->U1BC_LEDConfigure ); // LED_1 Off - pHwData->LED_Blinking = 0; - TimeInterval = 300; - } - } - else - { - //Turn Off LED_1 - if( reg->U1BC_LEDConfigure & 0x1000 ) - { - reg->U1BC_LEDConfigure &= ~0x1000; - Wb35Reg_Write( pHwData, 0x03bc, reg->U1BC_LEDConfigure ); // LED_1 Off - } - } - } - else - { - // Is transmitting/receiving ?? - if( (OS_CURRENT_RX_BYTE( adapter ) != pHwData->RxByteCountLast ) || - (OS_CURRENT_TX_BYTE( adapter ) != pHwData->TxByteCountLast ) ) - { - if( (reg->U1BC_LEDConfigure & 0x3000) != 0x3000 ) - { - reg->U1BC_LEDConfigure |= 0x3000; - Wb35Reg_Write( pHwData, 0x03bc, reg->U1BC_LEDConfigure ); // LED_1 On - } - - // Update variable - pHwData->RxByteCountLast = OS_CURRENT_RX_BYTE( adapter ); - pHwData->TxByteCountLast = OS_CURRENT_TX_BYTE( adapter ); - TimeInterval = 200; - } - else - { - // Turn On LED_1 and blinking if transmitting/receiving - if( (reg->U1BC_LEDConfigure & 0x3000) != 0x1000 ) - { - reg->U1BC_LEDConfigure &= ~0x3000; - reg->U1BC_LEDConfigure |= 0x1000; - Wb35Reg_Write( pHwData, 0x03bc, reg->U1BC_LEDConfigure ); // LED_1 On - } - } - } - break; - - default: // Default setting. 2 LED be placed on PCB. LED_0: Link On LED_1 Active - if( (reg->U1BC_LEDConfigure & 0x3000) != 0x3000 ) - { - reg->U1BC_LEDConfigure |= 0x3000;// LED_1 is always on and event enable - Wb35Reg_Write( pHwData, 0x03bc, reg->U1BC_LEDConfigure ); - } - - if( pHwData->LED_Blinking ) - { - // Gray blinking - reg->U1BC_LEDConfigure &= ~0x0f; - reg->U1BC_LEDConfigure |= 0x10; - reg->U1BC_LEDConfigure |= LEDgray[ (pHwData->LED_Blinking-1)%20 ]; - Wb35Reg_Write( pHwData, 0x03bc, reg->U1BC_LEDConfigure ); - - pHwData->LED_Blinking += 2; - if( pHwData->LED_Blinking < 40 ) - TimeInterval = 100; - else - { - pHwData->LED_Blinking = 0; // Stop blinking - reg->U1BC_LEDConfigure &= ~0x0f; - Wb35Reg_Write( pHwData, 0x03bc, reg->U1BC_LEDConfigure ); - } - break; - } - - if( pHwData->LED_LinkOn ) - { - if( !(reg->U1BC_LEDConfigure & 0x10) ) // Check the LED_0 - { - //Try to turn ON LED_0 after gray blinking - reg->U1BC_LEDConfigure |= 0x10; - pHwData->LED_Blinking = 1; //Start blinking - TimeInterval = 50; - } - } - else - { - if( reg->U1BC_LEDConfigure & 0x10 ) // Check the LED_0 - { - reg->U1BC_LEDConfigure &= ~0x10; - Wb35Reg_Write( pHwData, 0x03bc, reg->U1BC_LEDConfigure ); - } - } - break; - } - - //20060828.1 Active send null packet to avoid AP disconnect - if( pHwData->LED_LinkOn ) - { - pHwData->NullPacketCount += TimeInterval; - if( pHwData->NullPacketCount >= DEFAULT_NULL_PACKET_COUNT ) - { - pHwData->NullPacketCount = 0; - } - } - } - - pHwData->time_count += TimeInterval; - Wb35Tx_CurrentTime( pHwData, pHwData->time_count ); // 20060928 add - OS_TIMER_SET( &pHwData->LEDTimer, TimeInterval ); // 20060623.1 -} - void hal_set_phy_type( phw_data_t pHwData, u8 PhyType ) { @@ -867,7 +868,8 @@ unsigned char hal_set_LED(phw_data_t pHwData, u32 Mode) // 20061108 for WPS led { pHwData->LED_Blinking = 0; pHwData->LED_control = Mode; - OS_TIMER_SET( &pHwData->LEDTimer, 10 ); // 20060623 + pHwData->LEDTimer.expires = jiffies + msecs_to_jiffies(10); + add_timer(&pHwData->LEDTimer); return true; } diff --git a/drivers/staging/winbond/wbhal_f.h b/drivers/staging/winbond/wbhal_f.h index 239c301..7e6ebf2 100644 --- a/drivers/staging/winbond/wbhal_f.h +++ b/drivers/staging/winbond/wbhal_f.h @@ -68,8 +68,6 @@ s32 hal_get_rssi( phw_data_t pHwData, u32 *HalRssiArry, u8 Count ); s32 hal_get_rssi_bss( phw_data_t pHwData, u16 idx, u8 Count ); void hal_set_connect_info( phw_data_t pHwData, unsigned char boConnect ); u8 hal_get_est_sq3( phw_data_t pHwData, u8 Count ); -void hal_led_control_1a( phw_data_t pHwData ); -void hal_led_control( void* S1, phw_data_t pHwData, void* S3, void* S4 ); void hal_set_rf_power( phw_data_t pHwData, u8 PowerIndex ); // 20060621 Modify void hal_reset_counter( phw_data_t pHwData ); void hal_set_radio_mode( phw_data_t pHwData, unsigned char boValue); diff --git a/drivers/staging/winbond/wbhal_s.h b/drivers/staging/winbond/wbhal_s.h index 47f99e1..2d3adfc 100644 --- a/drivers/staging/winbond/wbhal_s.h +++ b/drivers/staging/winbond/wbhal_s.h @@ -510,7 +510,7 @@ typedef struct _HW_DATA_T WB35TX Wb35Tx; // Need Wb35Tx.h WB35RX Wb35Rx; // Need Wb35Rx.h - OS_TIMER LEDTimer;// For LED + struct timer_list LEDTimer;// For LED u32 LEDpoint;// For LED |