diff options
Diffstat (limited to 'drivers/usb/host')
-rw-r--r-- | drivers/usb/host/xhci-mem.c | 17 | ||||
-rw-r--r-- | drivers/usb/host/xhci-pci.c | 91 | ||||
-rw-r--r-- | drivers/usb/host/xhci-ring.c | 43 | ||||
-rw-r--r-- | drivers/usb/host/xhci.c | 24 |
4 files changed, 101 insertions, 74 deletions
diff --git a/drivers/usb/host/xhci-mem.c b/drivers/usb/host/xhci-mem.c index 9a8c936..41f841f 100644 --- a/drivers/usb/host/xhci-mem.c +++ b/drivers/usb/host/xhci-mem.c @@ -1498,10 +1498,10 @@ int xhci_endpoint_init(struct xhci_hcd *xhci, * use Event Data TRBs, and we don't chain in a link TRB on short * transfers, we're basically dividing by 1. * - * xHCI 1.0 specification indicates that the Average TRB Length should - * be set to 8 for control endpoints. + * xHCI 1.0 and 1.1 specification indicates that the Average TRB Length + * should be set to 8 for control endpoints. */ - if (usb_endpoint_xfer_control(&ep->desc) && xhci->hci_version == 0x100) + if (usb_endpoint_xfer_control(&ep->desc) && xhci->hci_version >= 0x100) ep_ctx->tx_info |= cpu_to_le32(AVG_TRB_LENGTH_FOR_EP(8)); else ep_ctx->tx_info |= @@ -1792,8 +1792,7 @@ void xhci_mem_cleanup(struct xhci_hcd *xhci) int size; int i, j, num_ports; - if (timer_pending(&xhci->cmd_timer)) - del_timer_sync(&xhci->cmd_timer); + del_timer_sync(&xhci->cmd_timer); /* Free the Event Ring Segment Table and the actual Event Ring */ size = sizeof(struct xhci_erst_entry)*(xhci->erst.num_entries); @@ -2321,6 +2320,10 @@ int xhci_mem_init(struct xhci_hcd *xhci, gfp_t flags) INIT_LIST_HEAD(&xhci->cmd_list); + /* init command timeout timer */ + setup_timer(&xhci->cmd_timer, xhci_handle_command_timeout, + (unsigned long)xhci); + page_size = readl(&xhci->op_regs->page_size); xhci_dbg_trace(xhci, trace_xhci_dbg_init, "Supported page size register = 0x%x", page_size); @@ -2505,10 +2508,6 @@ int xhci_mem_init(struct xhci_hcd *xhci, gfp_t flags) "Wrote ERST address to ir_set 0."); xhci_print_ir_set(xhci, 0); - /* init command timeout timer */ - setup_timer(&xhci->cmd_timer, xhci_handle_command_timeout, - (unsigned long)xhci); - /* * XXX: Might need to set the Interrupter Moderation Register to * something other than the default (~1ms minimum between interrupts). diff --git a/drivers/usb/host/xhci-pci.c b/drivers/usb/host/xhci-pci.c index 5590eac..c47d3e4 100644 --- a/drivers/usb/host/xhci-pci.c +++ b/drivers/usb/host/xhci-pci.c @@ -147,6 +147,7 @@ static void xhci_pci_quirks(struct device *dev, struct xhci_hcd *xhci) if (pdev->vendor == PCI_VENDOR_ID_INTEL && pdev->device == PCI_DEVICE_ID_INTEL_LYNXPOINT_LP_XHCI) { xhci->quirks |= XHCI_SPURIOUS_REBOOT; + xhci->quirks |= XHCI_SPURIOUS_WAKEUP; } if (pdev->vendor == PCI_VENDOR_ID_INTEL && (pdev->device == PCI_DEVICE_ID_INTEL_SUNRISEPOINT_LP_XHCI || @@ -180,51 +181,6 @@ static void xhci_pci_quirks(struct device *dev, struct xhci_hcd *xhci) "QUIRK: Resetting on resume"); } -/* - * In some Intel xHCI controllers, in order to get D3 working, - * through a vendor specific SSIC CONFIG register at offset 0x883c, - * SSIC PORT need to be marked as "unused" before putting xHCI - * into D3. After D3 exit, the SSIC port need to be marked as "used". - * Without this change, xHCI might not enter D3 state. - * Make sure PME works on some Intel xHCI controllers by writing 1 to clear - * the Internal PME flag bit in vendor specific PMCTRL register at offset 0x80a4 - */ -static void xhci_pme_quirk(struct usb_hcd *hcd, bool suspend) -{ - struct xhci_hcd *xhci = hcd_to_xhci(hcd); - struct pci_dev *pdev = to_pci_dev(hcd->self.controller); - u32 val; - void __iomem *reg; - - if (pdev->vendor == PCI_VENDOR_ID_INTEL && - pdev->device == PCI_DEVICE_ID_INTEL_CHERRYVIEW_XHCI) { - - reg = (void __iomem *) xhci->cap_regs + PORT2_SSIC_CONFIG_REG2; - - /* Notify SSIC that SSIC profile programming is not done */ - val = readl(reg) & ~PROG_DONE; - writel(val, reg); - - /* Mark SSIC port as unused(suspend) or used(resume) */ - val = readl(reg); - if (suspend) - val |= SSIC_PORT_UNUSED; - else - val &= ~SSIC_PORT_UNUSED; - writel(val, reg); - - /* Notify SSIC that SSIC profile programming is done */ - val = readl(reg) | PROG_DONE; - writel(val, reg); - readl(reg); - } - - reg = (void __iomem *) xhci->cap_regs + 0x80a4; - val = readl(reg); - writel(val | BIT(28), reg); - readl(reg); -} - #ifdef CONFIG_ACPI static void xhci_pme_acpi_rtd3_enable(struct pci_dev *dev) { @@ -345,6 +301,51 @@ static void xhci_pci_remove(struct pci_dev *dev) } #ifdef CONFIG_PM +/* + * In some Intel xHCI controllers, in order to get D3 working, + * through a vendor specific SSIC CONFIG register at offset 0x883c, + * SSIC PORT need to be marked as "unused" before putting xHCI + * into D3. After D3 exit, the SSIC port need to be marked as "used". + * Without this change, xHCI might not enter D3 state. + * Make sure PME works on some Intel xHCI controllers by writing 1 to clear + * the Internal PME flag bit in vendor specific PMCTRL register at offset 0x80a4 + */ +static void xhci_pme_quirk(struct usb_hcd *hcd, bool suspend) +{ + struct xhci_hcd *xhci = hcd_to_xhci(hcd); + struct pci_dev *pdev = to_pci_dev(hcd->self.controller); + u32 val; + void __iomem *reg; + + if (pdev->vendor == PCI_VENDOR_ID_INTEL && + pdev->device == PCI_DEVICE_ID_INTEL_CHERRYVIEW_XHCI) { + + reg = (void __iomem *) xhci->cap_regs + PORT2_SSIC_CONFIG_REG2; + + /* Notify SSIC that SSIC profile programming is not done */ + val = readl(reg) & ~PROG_DONE; + writel(val, reg); + + /* Mark SSIC port as unused(suspend) or used(resume) */ + val = readl(reg); + if (suspend) + val |= SSIC_PORT_UNUSED; + else + val &= ~SSIC_PORT_UNUSED; + writel(val, reg); + + /* Notify SSIC that SSIC profile programming is done */ + val = readl(reg) | PROG_DONE; + writel(val, reg); + readl(reg); + } + + reg = (void __iomem *) xhci->cap_regs + 0x80a4; + val = readl(reg); + writel(val | BIT(28), reg); + readl(reg); +} + static int xhci_pci_suspend(struct usb_hcd *hcd, bool do_wakeup) { struct xhci_hcd *xhci = hcd_to_xhci(hcd); diff --git a/drivers/usb/host/xhci-ring.c b/drivers/usb/host/xhci-ring.c index a47a1e8..97ffe39 100644 --- a/drivers/usb/host/xhci-ring.c +++ b/drivers/usb/host/xhci-ring.c @@ -302,6 +302,15 @@ static int xhci_abort_cmd_ring(struct xhci_hcd *xhci) ret = xhci_handshake(&xhci->op_regs->cmd_ring, CMD_RING_RUNNING, 0, 5 * 1000 * 1000); if (ret < 0) { + /* we are about to kill xhci, give it one more chance */ + xhci_write_64(xhci, temp_64 | CMD_RING_ABORT, + &xhci->op_regs->cmd_ring); + udelay(1000); + ret = xhci_handshake(&xhci->op_regs->cmd_ring, + CMD_RING_RUNNING, 0, 3 * 1000 * 1000); + if (ret == 0) + return 0; + xhci_err(xhci, "Stopped the command ring failed, " "maybe the host is dead\n"); xhci->xhc_state |= XHCI_STATE_DYING; @@ -2182,6 +2191,10 @@ static int process_bulk_intr_td(struct xhci_hcd *xhci, struct xhci_td *td, } /* Fast path - was this the last TRB in the TD for this URB? */ } else if (event_trb == td->last_trb) { + if (td->urb_length_set && trb_comp_code == COMP_SHORT_TX) + return finish_td(xhci, td, event_trb, event, ep, + status, false); + if (EVENT_TRB_LEN(le32_to_cpu(event->transfer_len)) != 0) { td->urb->actual_length = td->urb->transfer_buffer_length - @@ -2233,6 +2246,12 @@ static int process_bulk_intr_td(struct xhci_hcd *xhci, struct xhci_td *td, td->urb->actual_length += TRB_LEN(le32_to_cpu(cur_trb->generic.field[2])) - EVENT_TRB_LEN(le32_to_cpu(event->transfer_len)); + + if (trb_comp_code == COMP_SHORT_TX) { + xhci_dbg(xhci, "mid bulk/intr SP, wait for last TRB event\n"); + td->urb_length_set = true; + return 0; + } } return finish_td(xhci, td, event_trb, event, ep, status, false); @@ -2265,6 +2284,7 @@ static int handle_tx_event(struct xhci_hcd *xhci, u32 trb_comp_code; int ret = 0; int td_num = 0; + bool handling_skipped_tds = false; slot_id = TRB_TO_SLOT_ID(le32_to_cpu(event->flags)); xdev = xhci->devs[slot_id]; @@ -2401,6 +2421,10 @@ static int handle_tx_event(struct xhci_hcd *xhci, ep->skip = true; xhci_dbg(xhci, "Miss service interval error, set skip flag\n"); goto cleanup; + case COMP_PING_ERR: + ep->skip = true; + xhci_dbg(xhci, "No Ping response error, Skip one Isoc TD\n"); + goto cleanup; default: if (xhci_is_vendor_info_code(xhci, trb_comp_code)) { status = 0; @@ -2537,13 +2561,18 @@ static int handle_tx_event(struct xhci_hcd *xhci, ep, &status); cleanup: + + + handling_skipped_tds = ep->skip && + trb_comp_code != COMP_MISSED_INT && + trb_comp_code != COMP_PING_ERR; + /* - * Do not update event ring dequeue pointer if ep->skip is set. - * Will roll back to continue process missed tds. + * Do not update event ring dequeue pointer if we're in a loop + * processing missed tds. */ - if (trb_comp_code == COMP_MISSED_INT || !ep->skip) { + if (!handling_skipped_tds) inc_deq(xhci, xhci->event_ring); - } if (ret) { urb = td->urb; @@ -2578,7 +2607,7 @@ cleanup: * Process them as short transfer until reach the td pointed by * the event. */ - } while (ep->skip && trb_comp_code != COMP_MISSED_INT); + } while (handling_skipped_tds); return 0; } @@ -3461,8 +3490,8 @@ int xhci_queue_ctrl_tx(struct xhci_hcd *xhci, gfp_t mem_flags, if (start_cycle == 0) field |= 0x1; - /* xHCI 1.0 6.4.1.2.1: Transfer Type field */ - if (xhci->hci_version == 0x100) { + /* xHCI 1.0/1.1 6.4.1.2.1: Transfer Type field */ + if (xhci->hci_version >= 0x100) { if (urb->transfer_buffer_length > 0) { if (setup->bRequestType & USB_DIR_IN) field |= TRB_TX_TYPE(TRB_DATA_IN); diff --git a/drivers/usb/host/xhci.c b/drivers/usb/host/xhci.c index 6b0f4a4..9957bd9 100644 --- a/drivers/usb/host/xhci.c +++ b/drivers/usb/host/xhci.c @@ -146,7 +146,8 @@ static int xhci_start(struct xhci_hcd *xhci) "waited %u microseconds.\n", XHCI_MAX_HALT_USEC); if (!ret) - xhci->xhc_state &= ~XHCI_STATE_HALTED; + xhci->xhc_state &= ~(XHCI_STATE_HALTED | XHCI_STATE_DYING); + return ret; } @@ -654,15 +655,6 @@ int xhci_run(struct usb_hcd *hcd) } EXPORT_SYMBOL_GPL(xhci_run); -static void xhci_only_stop_hcd(struct usb_hcd *hcd) -{ - struct xhci_hcd *xhci = hcd_to_xhci(hcd); - - spin_lock_irq(&xhci->lock); - xhci_halt(xhci); - spin_unlock_irq(&xhci->lock); -} - /* * Stop xHCI driver. * @@ -677,12 +669,14 @@ void xhci_stop(struct usb_hcd *hcd) u32 temp; struct xhci_hcd *xhci = hcd_to_xhci(hcd); - if (!usb_hcd_is_primary_hcd(hcd)) { - xhci_only_stop_hcd(xhci->shared_hcd); + if (xhci->xhc_state & XHCI_STATE_HALTED) return; - } + mutex_lock(&xhci->mutex); spin_lock_irq(&xhci->lock); + xhci->xhc_state |= XHCI_STATE_HALTED; + xhci->cmd_ring_state = CMD_RING_STATE_STOPPED; + /* Make sure the xHC is halted for a USB3 roothub * (xhci_stop() could be called as part of failed init). */ @@ -717,6 +711,7 @@ void xhci_stop(struct usb_hcd *hcd) xhci_dbg_trace(xhci, trace_xhci_dbg_init, "xhci_stop completed - status = %x", readl(&xhci->op_regs->status)); + mutex_unlock(&xhci->mutex); } /* @@ -3793,6 +3788,9 @@ static int xhci_setup_device(struct usb_hcd *hcd, struct usb_device *udev, mutex_lock(&xhci->mutex); + if (xhci->xhc_state) /* dying or halted */ + goto out; + if (!udev->slot_id) { xhci_dbg_trace(xhci, trace_xhci_dbg_address, "Bad Slot ID %d", udev->slot_id); |