diff options
Diffstat (limited to 'drivers/usb/serial/mos7840.c')
| -rw-r--r-- | drivers/usb/serial/mos7840.c | 349 |
1 files changed, 166 insertions, 183 deletions
diff --git a/drivers/usb/serial/mos7840.c b/drivers/usb/serial/mos7840.c index bc3df86..1cf3375 100644 --- a/drivers/usb/serial/mos7840.c +++ b/drivers/usb/serial/mos7840.c @@ -2340,208 +2340,191 @@ static int mos7840_port_probe(struct usb_serial_port *port) pnum = port->number - serial->minor; - /* FIXME: remove do-while(0) loop used to keep stable patch minimal. - */ - do { - dev_dbg(&port->dev, "mos7840_startup: configuring port %d............\n", pnum); - mos7840_port = kzalloc(sizeof(struct moschip_port), GFP_KERNEL); - if (mos7840_port == NULL) { - dev_err(&port->dev, "%s - Out of memory\n", __func__); - return -ENOMEM; - } - - /* Initialize all port interrupt end point to port 0 int - * endpoint. Our device has only one interrupt end point - * common to all port */ - - mos7840_port->port = port; - mos7840_set_port_private(port, mos7840_port); - spin_lock_init(&mos7840_port->pool_lock); - - /* minor is not initialised until later by - * usb-serial.c:get_free_serial() and cannot therefore be used - * to index device instances */ - mos7840_port->port_num = pnum + 1; - dev_dbg(&port->dev, "port->number = %d\n", port->number); - dev_dbg(&port->dev, "port->serial->minor = %d\n", port->serial->minor); - dev_dbg(&port->dev, "mos7840_port->port_num = %d\n", mos7840_port->port_num); - dev_dbg(&port->dev, "serial->minor = %d\n", serial->minor); - - if (mos7840_port->port_num == 1) { - mos7840_port->SpRegOffset = 0x0; - mos7840_port->ControlRegOffset = 0x1; - mos7840_port->DcrRegOffset = 0x4; - } else if ((mos7840_port->port_num == 2) - && (serial->num_ports == 4)) { - mos7840_port->SpRegOffset = 0x8; - mos7840_port->ControlRegOffset = 0x9; - mos7840_port->DcrRegOffset = 0x16; - } else if ((mos7840_port->port_num == 2) - && (serial->num_ports == 2)) { - mos7840_port->SpRegOffset = 0xa; - mos7840_port->ControlRegOffset = 0xb; - mos7840_port->DcrRegOffset = 0x19; - } else if ((mos7840_port->port_num == 3) - && (serial->num_ports == 4)) { - mos7840_port->SpRegOffset = 0xa; - mos7840_port->ControlRegOffset = 0xb; - mos7840_port->DcrRegOffset = 0x19; - } else if ((mos7840_port->port_num == 4) - && (serial->num_ports == 4)) { - mos7840_port->SpRegOffset = 0xc; - mos7840_port->ControlRegOffset = 0xd; - mos7840_port->DcrRegOffset = 0x1c; - } - mos7840_dump_serial_port(port, mos7840_port); - mos7840_set_port_private(port, mos7840_port); + dev_dbg(&port->dev, "mos7840_startup: configuring port %d\n", pnum); + mos7840_port = kzalloc(sizeof(struct moschip_port), GFP_KERNEL); + if (mos7840_port == NULL) { + dev_err(&port->dev, "%s - Out of memory\n", __func__); + return -ENOMEM; + } - /* enable rx_disable bit in control register */ - status = mos7840_get_reg_sync(port, - mos7840_port->ControlRegOffset, &Data); - if (status < 0) { - dev_dbg(&port->dev, "Reading ControlReg failed status-0x%x\n", status); - break; - } else - dev_dbg(&port->dev, "ControlReg Reading success val is %x, status%d\n", Data, status); - Data |= 0x08; /* setting driver done bit */ - Data |= 0x04; /* sp1_bit to have cts change reflect in - modem status reg */ + /* Initialize all port interrupt end point to port 0 int + * endpoint. Our device has only one interrupt end point + * common to all port */ + + mos7840_port->port = port; + mos7840_set_port_private(port, mos7840_port); + spin_lock_init(&mos7840_port->pool_lock); + + /* minor is not initialised until later by + * usb-serial.c:get_free_serial() and cannot therefore be used + * to index device instances */ + mos7840_port->port_num = pnum + 1; + dev_dbg(&port->dev, "port->number = %d\n", port->number); + dev_dbg(&port->dev, "port->serial->minor = %d\n", port->serial->minor); + dev_dbg(&port->dev, "mos7840_port->port_num = %d\n", mos7840_port->port_num); + dev_dbg(&port->dev, "serial->minor = %d\n", serial->minor); + + if (mos7840_port->port_num == 1) { + mos7840_port->SpRegOffset = 0x0; + mos7840_port->ControlRegOffset = 0x1; + mos7840_port->DcrRegOffset = 0x4; + } else if ((mos7840_port->port_num == 2) && (serial->num_ports == 4)) { + mos7840_port->SpRegOffset = 0x8; + mos7840_port->ControlRegOffset = 0x9; + mos7840_port->DcrRegOffset = 0x16; + } else if ((mos7840_port->port_num == 2) && (serial->num_ports == 2)) { + mos7840_port->SpRegOffset = 0xa; + mos7840_port->ControlRegOffset = 0xb; + mos7840_port->DcrRegOffset = 0x19; + } else if ((mos7840_port->port_num == 3) && (serial->num_ports == 4)) { + mos7840_port->SpRegOffset = 0xa; + mos7840_port->ControlRegOffset = 0xb; + mos7840_port->DcrRegOffset = 0x19; + } else if ((mos7840_port->port_num == 4) && (serial->num_ports == 4)) { + mos7840_port->SpRegOffset = 0xc; + mos7840_port->ControlRegOffset = 0xd; + mos7840_port->DcrRegOffset = 0x1c; + } + mos7840_dump_serial_port(port, mos7840_port); + mos7840_set_port_private(port, mos7840_port); + + /* enable rx_disable bit in control register */ + status = mos7840_get_reg_sync(port, + mos7840_port->ControlRegOffset, &Data); + if (status < 0) { + dev_dbg(&port->dev, "Reading ControlReg failed status-0x%x\n", status); + goto out; + } else + dev_dbg(&port->dev, "ControlReg Reading success val is %x, status%d\n", Data, status); + Data |= 0x08; /* setting driver done bit */ + Data |= 0x04; /* sp1_bit to have cts change reflect in + modem status reg */ + + /* Data |= 0x20; //rx_disable bit */ + status = mos7840_set_reg_sync(port, + mos7840_port->ControlRegOffset, Data); + if (status < 0) { + dev_dbg(&port->dev, "Writing ControlReg failed(rx_disable) status-0x%x\n", status); + goto out; + } else + dev_dbg(&port->dev, "ControlReg Writing success(rx_disable) status%d\n", status); + + /* Write default values in DCR (i.e 0x01 in DCR0, 0x05 in DCR2 + and 0x24 in DCR3 */ + Data = 0x01; + status = mos7840_set_reg_sync(port, + (__u16) (mos7840_port->DcrRegOffset + 0), Data); + if (status < 0) { + dev_dbg(&port->dev, "Writing DCR0 failed status-0x%x\n", status); + goto out; + } else + dev_dbg(&port->dev, "DCR0 Writing success status%d\n", status); - /* Data |= 0x20; //rx_disable bit */ - status = mos7840_set_reg_sync(port, - mos7840_port->ControlRegOffset, Data); - if (status < 0) { - dev_dbg(&port->dev, "Writing ControlReg failed(rx_disable) status-0x%x\n", status); - break; - } else - dev_dbg(&port->dev, "ControlReg Writing success(rx_disable) status%d\n", status); + Data = 0x05; + status = mos7840_set_reg_sync(port, + (__u16) (mos7840_port->DcrRegOffset + 1), Data); + if (status < 0) { + dev_dbg(&port->dev, "Writing DCR1 failed status-0x%x\n", status); + goto out; + } else + dev_dbg(&port->dev, "DCR1 Writing success status%d\n", status); - /* Write default values in DCR (i.e 0x01 in DCR0, 0x05 in DCR2 - and 0x24 in DCR3 */ - Data = 0x01; - status = mos7840_set_reg_sync(port, - (__u16) (mos7840_port->DcrRegOffset + 0), Data); - if (status < 0) { - dev_dbg(&port->dev, "Writing DCR0 failed status-0x%x\n", status); - break; - } else - dev_dbg(&port->dev, "DCR0 Writing success status%d\n", status); + Data = 0x24; + status = mos7840_set_reg_sync(port, + (__u16) (mos7840_port->DcrRegOffset + 2), Data); + if (status < 0) { + dev_dbg(&port->dev, "Writing DCR2 failed status-0x%x\n", status); + goto out; + } else + dev_dbg(&port->dev, "DCR2 Writing success status%d\n", status); - Data = 0x05; - status = mos7840_set_reg_sync(port, - (__u16) (mos7840_port->DcrRegOffset + 1), Data); - if (status < 0) { - dev_dbg(&port->dev, "Writing DCR1 failed status-0x%x\n", status); - break; - } else - dev_dbg(&port->dev, "DCR1 Writing success status%d\n", status); + /* write values in clkstart0x0 and clkmulti 0x20 */ + Data = 0x0; + status = mos7840_set_reg_sync(port, CLK_START_VALUE_REGISTER, Data); + if (status < 0) { + dev_dbg(&port->dev, "Writing CLK_START_VALUE_REGISTER failed status-0x%x\n", status); + goto out; + } else + dev_dbg(&port->dev, "CLK_START_VALUE_REGISTER Writing success status%d\n", status); - Data = 0x24; - status = mos7840_set_reg_sync(port, - (__u16) (mos7840_port->DcrRegOffset + 2), Data); - if (status < 0) { - dev_dbg(&port->dev, "Writing DCR2 failed status-0x%x\n", status); - break; - } else - dev_dbg(&port->dev, "DCR2 Writing success status%d\n", status); + Data = 0x20; + status = mos7840_set_reg_sync(port, CLK_MULTI_REGISTER, Data); + if (status < 0) { + dev_dbg(&port->dev, "Writing CLK_MULTI_REGISTER failed status-0x%x\n", status); + goto error; + } else + dev_dbg(&port->dev, "CLK_MULTI_REGISTER Writing success status%d\n", status); - /* write values in clkstart0x0 and clkmulti 0x20 */ - Data = 0x0; + /* write value 0x0 to scratchpad register */ + Data = 0x00; + status = mos7840_set_uart_reg(port, SCRATCH_PAD_REGISTER, Data); + if (status < 0) { + dev_dbg(&port->dev, "Writing SCRATCH_PAD_REGISTER failed status-0x%x\n", status); + goto out; + } else + dev_dbg(&port->dev, "SCRATCH_PAD_REGISTER Writing success status%d\n", status); + + /* Zero Length flag register */ + if ((mos7840_port->port_num != 1) && (serial->num_ports == 2)) { + Data = 0xff; status = mos7840_set_reg_sync(port, - CLK_START_VALUE_REGISTER, Data); + (__u16) (ZLP_REG1 + + ((__u16)mos7840_port->port_num)), Data); + dev_dbg(&port->dev, "ZLIP offset %x\n", + (__u16)(ZLP_REG1 + ((__u16) mos7840_port->port_num))); if (status < 0) { - dev_dbg(&port->dev, "Writing CLK_START_VALUE_REGISTER failed status-0x%x\n", status); - break; + dev_dbg(&port->dev, "Writing ZLP_REG%d failed status-0x%x\n", pnum + 2, status); + goto out; } else - dev_dbg(&port->dev, "CLK_START_VALUE_REGISTER Writing success status%d\n", status); - - Data = 0x20; + dev_dbg(&port->dev, "ZLP_REG%d Writing success status%d\n", pnum + 2, status); + } else { + Data = 0xff; status = mos7840_set_reg_sync(port, - CLK_MULTI_REGISTER, Data); - if (status < 0) { - dev_dbg(&port->dev, "Writing CLK_MULTI_REGISTER failed status-0x%x\n", status); - goto error; - } else - dev_dbg(&port->dev, "CLK_MULTI_REGISTER Writing success status%d\n", status); - - /* write value 0x0 to scratchpad register */ - Data = 0x00; - status = mos7840_set_uart_reg(port, - SCRATCH_PAD_REGISTER, Data); + (__u16) (ZLP_REG1 + + ((__u16)mos7840_port->port_num) - 0x1), Data); + dev_dbg(&port->dev, "ZLIP offset %x\n", + (__u16)(ZLP_REG1 + ((__u16) mos7840_port->port_num) - 0x1)); if (status < 0) { - dev_dbg(&port->dev, "Writing SCRATCH_PAD_REGISTER failed status-0x%x\n", status); - break; + dev_dbg(&port->dev, "Writing ZLP_REG%d failed status-0x%x\n", pnum + 1, status); + goto out; } else - dev_dbg(&port->dev, "SCRATCH_PAD_REGISTER Writing success status%d\n", status); + dev_dbg(&port->dev, "ZLP_REG%d Writing success status%d\n", pnum + 1, status); - /* Zero Length flag register */ - if ((mos7840_port->port_num != 1) - && (serial->num_ports == 2)) { - - Data = 0xff; - status = mos7840_set_reg_sync(port, - (__u16) (ZLP_REG1 + - ((__u16)mos7840_port->port_num)), Data); - dev_dbg(&port->dev, "ZLIP offset %x\n", - (__u16)(ZLP_REG1 + ((__u16) mos7840_port->port_num))); - if (status < 0) { - dev_dbg(&port->dev, "Writing ZLP_REG%d failed status-0x%x\n", pnum + 2, status); - break; - } else - dev_dbg(&port->dev, "ZLP_REG%d Writing success status%d\n", pnum + 2, status); - } else { - Data = 0xff; - status = mos7840_set_reg_sync(port, - (__u16) (ZLP_REG1 + - ((__u16)mos7840_port->port_num) - 0x1), Data); - dev_dbg(&port->dev, "ZLIP offset %x\n", - (__u16)(ZLP_REG1 + ((__u16) mos7840_port->port_num) - 0x1)); - if (status < 0) { - dev_dbg(&port->dev, "Writing ZLP_REG%d failed status-0x%x\n", pnum + 1, status); - break; - } else - dev_dbg(&port->dev, "ZLP_REG%d Writing success status%d\n", pnum + 1, status); - - } - mos7840_port->control_urb = usb_alloc_urb(0, GFP_KERNEL); - mos7840_port->ctrl_buf = kmalloc(16, GFP_KERNEL); - mos7840_port->dr = kmalloc(sizeof(struct usb_ctrlrequest), - GFP_KERNEL); - if (!mos7840_port->control_urb || !mos7840_port->ctrl_buf || - !mos7840_port->dr) { - status = -ENOMEM; - goto error; - } - - mos7840_port->has_led = false; + } + mos7840_port->control_urb = usb_alloc_urb(0, GFP_KERNEL); + mos7840_port->ctrl_buf = kmalloc(16, GFP_KERNEL); + mos7840_port->dr = kmalloc(sizeof(struct usb_ctrlrequest), + GFP_KERNEL); + if (!mos7840_port->control_urb || !mos7840_port->ctrl_buf || + !mos7840_port->dr) { + status = -ENOMEM; + goto error; + } - /* Initialize LED timers */ - if (device_type == MOSCHIP_DEVICE_ID_7810) { - mos7840_port->has_led = true; + mos7840_port->has_led = false; - init_timer(&mos7840_port->led_timer1); - mos7840_port->led_timer1.function = mos7840_led_off; - mos7840_port->led_timer1.expires = - jiffies + msecs_to_jiffies(LED_ON_MS); - mos7840_port->led_timer1.data = - (unsigned long)mos7840_port; + /* Initialize LED timers */ + if (device_type == MOSCHIP_DEVICE_ID_7810) { + mos7840_port->has_led = true; - init_timer(&mos7840_port->led_timer2); - mos7840_port->led_timer2.function = - mos7840_led_flag_off; - mos7840_port->led_timer2.expires = - jiffies + msecs_to_jiffies(LED_OFF_MS); - mos7840_port->led_timer2.data = - (unsigned long)mos7840_port; + init_timer(&mos7840_port->led_timer1); + mos7840_port->led_timer1.function = mos7840_led_off; + mos7840_port->led_timer1.expires = + jiffies + msecs_to_jiffies(LED_ON_MS); + mos7840_port->led_timer1.data = (unsigned long)mos7840_port; - mos7840_port->led_flag = false; + init_timer(&mos7840_port->led_timer2); + mos7840_port->led_timer2.function = mos7840_led_flag_off; + mos7840_port->led_timer2.expires = + jiffies + msecs_to_jiffies(LED_OFF_MS); + mos7840_port->led_timer2.data = (unsigned long)mos7840_port; - /* Turn off LED */ - mos7840_set_led_sync(port, - MODEM_CONTROL_REGISTER, 0x0300); - } - } while (0); + mos7840_port->led_flag = false; + /* Turn off LED */ + mos7840_set_led_sync(port, MODEM_CONTROL_REGISTER, 0x0300); + } +out: if (pnum == serial->num_ports - 1) { /* Zero Length flag enable */ Data = 0x0f; |