diff options
Diffstat (limited to 'drivers/usb')
| -rw-r--r-- | drivers/usb/core/hub.c | 42 |
1 files changed, 36 insertions, 6 deletions
diff --git a/drivers/usb/core/hub.c b/drivers/usb/core/hub.c index f3fe8dfa..3c28bde 100644 --- a/drivers/usb/core/hub.c +++ b/drivers/usb/core/hub.c @@ -2435,6 +2435,7 @@ hub_port_init (struct usb_hub *hub, struct usb_device *udev, int port1, static DEFINE_MUTEX(usb_address0_mutex); struct usb_device *hdev = hub->hdev; + struct usb_hcd *hcd = bus_to_hcd(hdev->bus); int i, j, retval; unsigned delay = HUB_SHORT_RESET_TIME; enum usb_device_speed oldspeed = udev->speed; @@ -2457,11 +2458,24 @@ hub_port_init (struct usb_hub *hub, struct usb_device *udev, int port1, mutex_lock(&usb_address0_mutex); - /* Reset the device; full speed may morph to high speed */ - retval = hub_port_reset(hub, port1, udev, delay); - if (retval < 0) /* error or disconnect */ + if ((hcd->driver->flags & HCD_USB3) && udev->config) { + /* FIXME this will need special handling by the xHCI driver. */ + dev_dbg(&udev->dev, + "xHCI reset of configured device " + "not supported yet.\n"); + retval = -EINVAL; goto fail; - /* success, speed is known */ + } else if (!udev->config && oldspeed == USB_SPEED_SUPER) { + /* Don't reset USB 3.0 devices during an initial setup */ + usb_set_device_state(udev, USB_STATE_DEFAULT); + } else { + /* Reset the device; full speed may morph to high speed */ + /* FIXME a USB 2.0 device may morph into SuperSpeed on reset. */ + retval = hub_port_reset(hub, port1, udev, delay); + if (retval < 0) /* error or disconnect */ + goto fail; + /* success, speed is known */ + } retval = -ENODEV; if (oldspeed != USB_SPEED_UNKNOWN && oldspeed != udev->speed) { @@ -2859,7 +2873,6 @@ static void hub_port_connect_change(struct usb_hub *hub, int port1, } usb_set_device_state(udev, USB_STATE_POWERED); - udev->speed = USB_SPEED_UNKNOWN; udev->bus_mA = hub->mA_per_port; udev->level = hdev->level + 1; udev->wusb = hub_is_wusb(hub); @@ -2871,7 +2884,24 @@ static void hub_port_connect_change(struct usb_hub *hub, int port1, goto loop; } - /* reset and get descriptor */ + /* + * USB 3.0 devices are reset automatically before the connect + * port status change appears, and the root hub port status + * shows the correct speed. We also get port change + * notifications for USB 3.0 devices from the USB 3.0 portion of + * an external USB 3.0 hub, but this isn't handled correctly yet + * FIXME. + */ + + if (!(hcd->driver->flags & HCD_USB3)) + udev->speed = USB_SPEED_UNKNOWN; + else if ((hdev->parent == NULL) && + (portstatus & (1 << USB_PORT_FEAT_SUPERSPEED))) + udev->speed = USB_SPEED_SUPER; + else + udev->speed = USB_SPEED_UNKNOWN; + + /* reset (non-USB 3.0 devices) and get descriptor */ status = hub_port_init(hub, udev, port1, i); if (status < 0) goto loop; |