diff options
Diffstat (limited to 'drivers/video/am200epd.c')
| -rw-r--r-- | drivers/video/am200epd.c | 295 |
1 files changed, 295 insertions, 0 deletions
diff --git a/drivers/video/am200epd.c b/drivers/video/am200epd.c new file mode 100644 index 0000000..51e26c1 --- /dev/null +++ b/drivers/video/am200epd.c @@ -0,0 +1,295 @@ +/* + * linux/drivers/video/am200epd.c -- Platform device for AM200 EPD kit + * + * Copyright (C) 2008, Jaya Kumar + * + * This file is subject to the terms and conditions of the GNU General Public + * License. See the file COPYING in the main directory of this archive for + * more details. + * + * Layout is based on skeletonfb.c by James Simmons and Geert Uytterhoeven. + * + * This work was made possible by help and equipment support from E-Ink + * Corporation. http://support.eink.com/community + * + * This driver is written to be used with the Metronome display controller. + * on the AM200 EPD prototype kit/development kit with an E-Ink 800x600 + * Vizplex EPD on a Gumstix board using the Lyre interface board. + * + */ + +#include <linux/module.h> +#include <linux/kernel.h> +#include <linux/errno.h> +#include <linux/string.h> +#include <linux/delay.h> +#include <linux/interrupt.h> +#include <linux/fb.h> +#include <linux/init.h> +#include <linux/platform_device.h> +#include <linux/list.h> +#include <linux/uaccess.h> +#include <linux/irq.h> + +#include <video/metronomefb.h> + +#include <asm/arch/pxa-regs.h> + +/* register offsets for gpio control */ +#define LED_GPIO_PIN 51 +#define STDBY_GPIO_PIN 48 +#define RST_GPIO_PIN 49 +#define RDY_GPIO_PIN 32 +#define ERR_GPIO_PIN 17 +#define PCBPWR_GPIO_PIN 16 + +#define AF_SEL_GPIO_N 0x3 +#define GAFR0_U_OFFSET(pin) ((pin - 16) * 2) +#define GAFR1_L_OFFSET(pin) ((pin - 32) * 2) +#define GAFR1_U_OFFSET(pin) ((pin - 48) * 2) +#define GPDR1_OFFSET(pin) (pin - 32) +#define GPCR1_OFFSET(pin) (pin - 32) +#define GPSR1_OFFSET(pin) (pin - 32) +#define GPCR0_OFFSET(pin) (pin) +#define GPSR0_OFFSET(pin) (pin) + +static void am200_set_gpio_output(int pin, int val) +{ + u8 index; + + index = pin >> 4; + + switch (index) { + case 1: + if (val) + GPSR0 |= (1 << GPSR0_OFFSET(pin)); + else + GPCR0 |= (1 << GPCR0_OFFSET(pin)); + break; + case 2: + break; + case 3: + if (val) + GPSR1 |= (1 << GPSR1_OFFSET(pin)); + else + GPCR1 |= (1 << GPCR1_OFFSET(pin)); + break; + default: + printk(KERN_ERR "unimplemented\n"); + } +} + +static void __devinit am200_init_gpio_pin(int pin, int dir) +{ + u8 index; + /* dir 0 is output, 1 is input + - do 2 things here: + - set gpio alternate function to standard gpio + - set gpio direction to input or output */ + + index = pin >> 4; + switch (index) { + case 1: + GAFR0_U &= ~(AF_SEL_GPIO_N << GAFR0_U_OFFSET(pin)); + + if (dir) + GPDR0 &= ~(1 << pin); + else + GPDR0 |= (1 << pin); + break; + case 2: + GAFR1_L &= ~(AF_SEL_GPIO_N << GAFR1_L_OFFSET(pin)); + + if (dir) + GPDR1 &= ~(1 << GPDR1_OFFSET(pin)); + else + GPDR1 |= (1 << GPDR1_OFFSET(pin)); + break; + case 3: + GAFR1_U &= ~(AF_SEL_GPIO_N << GAFR1_U_OFFSET(pin)); + + if (dir) + GPDR1 &= ~(1 << GPDR1_OFFSET(pin)); + else + GPDR1 |= (1 << GPDR1_OFFSET(pin)); + break; + default: + printk(KERN_ERR "unimplemented\n"); + } +} + +static void am200_init_gpio_regs(struct metronomefb_par *par) +{ + am200_init_gpio_pin(LED_GPIO_PIN, 0); + am200_set_gpio_output(LED_GPIO_PIN, 0); + + am200_init_gpio_pin(STDBY_GPIO_PIN, 0); + am200_set_gpio_output(STDBY_GPIO_PIN, 0); + + am200_init_gpio_pin(RST_GPIO_PIN, 0); + am200_set_gpio_output(RST_GPIO_PIN, 0); + + am200_init_gpio_pin(RDY_GPIO_PIN, 1); + + am200_init_gpio_pin(ERR_GPIO_PIN, 1); + + am200_init_gpio_pin(PCBPWR_GPIO_PIN, 0); + am200_set_gpio_output(PCBPWR_GPIO_PIN, 0); +} + +static void am200_disable_lcd_controller(struct metronomefb_par *par) +{ + LCSR = 0xffffffff; /* Clear LCD Status Register */ + LCCR0 |= LCCR0_DIS; /* Disable LCD Controller */ + + /* we reset and just wait for things to settle */ + msleep(200); +} + +static void am200_enable_lcd_controller(struct metronomefb_par *par) +{ + LCSR = 0xffffffff; + FDADR0 = par->metromem_desc_dma; + LCCR0 |= LCCR0_ENB; +} + +static void am200_init_lcdc_regs(struct metronomefb_par *par) +{ + /* here we do: + - disable the lcd controller + - setup lcd control registers + - setup dma descriptor + - reenable lcd controller + */ + + /* disable the lcd controller */ + am200_disable_lcd_controller(par); + + /* setup lcd control registers */ + LCCR0 = LCCR0_LDM | LCCR0_SFM | LCCR0_IUM | LCCR0_EFM | LCCR0_PAS + | LCCR0_QDM | LCCR0_BM | LCCR0_OUM; + + LCCR1 = (par->info->var.xres/2 - 1) /* pixels per line */ + | (27 << 10) /* hsync pulse width - 1 */ + | (33 << 16) /* eol pixel count */ + | (33 << 24); /* bol pixel count */ + + LCCR2 = (par->info->var.yres - 1) /* lines per panel */ + | (24 << 10) /* vsync pulse width - 1 */ + | (2 << 16) /* eof pixel count */ + | (0 << 24); /* bof pixel count */ + + LCCR3 = 2 /* pixel clock divisor */ + | (24 << 8) /* AC Bias pin freq */ + | LCCR3_16BPP /* BPP */ + | LCCR3_PCP; /* PCP falling edge */ + +} + +static void am200_post_dma_setup(struct metronomefb_par *par) +{ + par->metromem_desc->mFDADR0 = par->metromem_desc_dma; + par->metromem_desc->mFSADR0 = par->metromem_dma; + par->metromem_desc->mFIDR0 = 0; + par->metromem_desc->mLDCMD0 = par->info->var.xres + * par->info->var.yres; + am200_enable_lcd_controller(par); +} + +static void am200_free_irq(struct fb_info *info) +{ + free_irq(IRQ_GPIO(RDY_GPIO_PIN), info); +} + +static irqreturn_t am200_handle_irq(int irq, void *dev_id) +{ + struct fb_info *info = dev_id; + struct metronomefb_par *par = info->par; + + wake_up_interruptible(&par->waitq); + return IRQ_HANDLED; +} + +static int am200_setup_irq(struct fb_info *info) +{ + int retval; + + retval = request_irq(IRQ_GPIO(RDY_GPIO_PIN), am200_handle_irq, + IRQF_DISABLED, "AM200", info); + if (retval) { + printk(KERN_ERR "am200epd: request_irq failed: %d\n", retval); + return retval; + } + + return set_irq_type(IRQ_GPIO(RDY_GPIO_PIN), IRQT_FALLING); +} + +static void am200_set_rst(struct metronomefb_par *par, int state) +{ + am200_set_gpio_output(RST_GPIO_PIN, state); +} + +static void am200_set_stdby(struct metronomefb_par *par, int state) +{ + am200_set_gpio_output(STDBY_GPIO_PIN, state); +} + +static int am200_wait_event(struct metronomefb_par *par) +{ + return wait_event_timeout(par->waitq, (GPLR1 & 0x01), HZ); +} + +static int am200_wait_event_intr(struct metronomefb_par *par) +{ + return wait_event_interruptible_timeout(par->waitq, (GPLR1 & 0x01), HZ); +} + +static struct metronome_board am200_board = { + .owner = THIS_MODULE, + .free_irq = am200_free_irq, + .setup_irq = am200_setup_irq, + .init_gpio_regs = am200_init_gpio_regs, + .init_lcdc_regs = am200_init_lcdc_regs, + .post_dma_setup = am200_post_dma_setup, + .set_rst = am200_set_rst, + .set_stdby = am200_set_stdby, + .met_wait_event = am200_wait_event, + .met_wait_event_intr = am200_wait_event_intr, +}; + +static struct platform_device *am200_device; + +static int __init am200_init(void) +{ + int ret; + + /* request our platform independent driver */ + request_module("metronomefb"); + + am200_device = platform_device_alloc("metronomefb", -1); + if (!am200_device) + return -ENOMEM; + + platform_device_add_data(am200_device, &am200_board, + sizeof(am200_board)); + + /* this _add binds metronomefb to am200. metronomefb refcounts am200 */ + ret = platform_device_add(am200_device); + + if (ret) + platform_device_put(am200_device); + + return ret; +} + +static void __exit am200_exit(void) +{ + platform_device_unregister(am200_device); +} + +module_init(am200_init); +module_exit(am200_exit); + +MODULE_DESCRIPTION("board driver for am200 metronome epd kit"); +MODULE_AUTHOR("Jaya Kumar"); +MODULE_LICENSE("GPL"); |