diff options
Diffstat (limited to 'drivers')
101 files changed, 1149 insertions, 567 deletions
diff --git a/drivers/acpi/sleep/proc.c b/drivers/acpi/sleep/proc.c index 64e591b..4dbc227 100644 --- a/drivers/acpi/sleep/proc.c +++ b/drivers/acpi/sleep/proc.c @@ -366,7 +366,7 @@ acpi_system_wakeup_device_seq_show(struct seq_file *seq, void *offset) dev->wakeup.state.enabled ? "enabled" : "disabled"); if (ldev) seq_printf(seq, "%s:%s", - dev_name(ldev) ? ldev->bus->name : "no-bus", + ldev->bus ? ldev->bus->name : "no-bus", dev_name(ldev)); seq_printf(seq, "\n"); put_device(ldev); diff --git a/drivers/ata/libata-sff.c b/drivers/ata/libata-sff.c index 4b47394..9033d16 100644 --- a/drivers/ata/libata-sff.c +++ b/drivers/ata/libata-sff.c @@ -1227,10 +1227,19 @@ fsm_start: /* ATA PIO protocol */ if (unlikely((status & ATA_DRQ) == 0)) { /* handle BSY=0, DRQ=0 as error */ - if (likely(status & (ATA_ERR | ATA_DF))) + if (likely(status & (ATA_ERR | ATA_DF))) { /* device stops HSM for abort/error */ qc->err_mask |= AC_ERR_DEV; - else { + + /* If diagnostic failed and this is + * IDENTIFY, it's likely a phantom + * device. Mark hint. + */ + if (qc->dev->horkage & + ATA_HORKAGE_DIAGNOSTIC) + qc->err_mask |= + AC_ERR_NODEV_HINT; + } else { /* HSM violation. Let EH handle this. * Phantom devices also trigger this * condition. Mark hint. diff --git a/drivers/block/Kconfig b/drivers/block/Kconfig index 61ad8d6..0344a8a 100644 --- a/drivers/block/Kconfig +++ b/drivers/block/Kconfig @@ -21,7 +21,8 @@ config BLK_DEV_FD ---help--- If you want to use the floppy disk drive(s) of your PC under Linux, say Y. Information about this driver, especially important for IBM - Thinkpad users, is contained in <file:Documentation/floppy.txt>. + Thinkpad users, is contained in + <file:Documentation/blockdev/floppy.txt>. That file also contains the location of the Floppy driver FAQ as well as location of the fdutils package used to configure additional parameters of the driver at run time. @@ -76,7 +77,7 @@ config PARIDE your computer's parallel port. Most of them are actually IDE devices using a parallel port IDE adapter. This option enables the PARIDE subsystem which contains drivers for many of these external drives. - Read <file:Documentation/paride.txt> for more information. + Read <file:Documentation/blockdev/paride.txt> for more information. If you have said Y to the "Parallel-port support" configuration option, you may share a single port between your printer and other @@ -114,9 +115,9 @@ config BLK_CPQ_DA help This is the driver for Compaq Smart Array controllers. Everyone using these boards should say Y here. See the file - <file:Documentation/cpqarray.txt> for the current list of boards - supported by this driver, and for further information on the use of - this driver. + <file:Documentation/blockdev/cpqarray.txt> for the current list of + boards supported by this driver, and for further information on the + use of this driver. config BLK_CPQ_CISS_DA tristate "Compaq Smart Array 5xxx support" @@ -124,7 +125,7 @@ config BLK_CPQ_CISS_DA help This is the driver for Compaq Smart Array 5xxx controllers. Everyone using these boards should say Y here. - See <file:Documentation/cciss.txt> for the current list of + See <file:Documentation/blockdev/cciss.txt> for the current list of boards supported by this driver, and for further information on the use of this driver. @@ -135,7 +136,7 @@ config CISS_SCSI_TAPE help When enabled (Y), this option allows SCSI tape drives and SCSI medium changers (tape robots) to be accessed via a Compaq 5xxx array - controller. (See <file:Documentation/cciss.txt> for more details.) + controller. (See <file:Documentation/blockdev/cciss.txt> for more details.) "SCSI support" and "SCSI tape support" must also be enabled for this option to work. @@ -149,8 +150,8 @@ config BLK_DEV_DAC960 help This driver adds support for the Mylex DAC960, AcceleRAID, and eXtremeRAID PCI RAID controllers. See the file - <file:Documentation/README.DAC960> for further information about - this driver. + <file:Documentation/blockdev/README.DAC960> for further information + about this driver. To compile this driver as a module, choose M here: the module will be called DAC960. @@ -278,9 +279,9 @@ config BLK_DEV_NBD userland (making server and client physically the same computer, communicating using the loopback network device). - Read <file:Documentation/nbd.txt> for more information, especially - about where to find the server code, which runs in user space and - does not need special kernel support. + Read <file:Documentation/blockdev/nbd.txt> for more information, + especially about where to find the server code, which runs in user + space and does not need special kernel support. Note that this has nothing to do with the network file systems NFS or Coda; you can say N here even if you intend to use NFS or Coda. @@ -321,8 +322,8 @@ config BLK_DEV_RAM store a copy of a minimal root file system off of a floppy into RAM during the initial install of Linux. - Note that the kernel command line option "ramdisk=XX" is now - obsolete. For details, read <file:Documentation/ramdisk.txt>. + Note that the kernel command line option "ramdisk=XX" is now obsolete. + For details, read <file:Documentation/blockdev/ramdisk.txt>. To compile this driver as a module, choose M here: the module will be called rd. diff --git a/drivers/block/floppy.c b/drivers/block/floppy.c index 14db747..cf29cc4 100644 --- a/drivers/block/floppy.c +++ b/drivers/block/floppy.c @@ -4124,7 +4124,7 @@ static int __init floppy_setup(char *str) printk("\n"); } else DPRINT("botched floppy option\n"); - DPRINT("Read Documentation/floppy.txt\n"); + DPRINT("Read Documentation/blockdev/floppy.txt\n"); return 0; } diff --git a/drivers/block/ub.c b/drivers/block/ub.c index fccac18..048d71d 100644 --- a/drivers/block/ub.c +++ b/drivers/block/ub.c @@ -1546,8 +1546,6 @@ static void ub_top_sense_done(struct ub_dev *sc, struct ub_scsi_cmd *scmd) /* * Reset management - * XXX Move usb_reset_device to khubd. Hogging kevent is not a good thing. - * XXX Make usb_sync_reset asynchronous. */ static void ub_reset_enter(struct ub_dev *sc, int try) @@ -1633,6 +1631,22 @@ static void ub_reset_task(struct work_struct *work) } /* + * XXX Reset brackets are too much hassle to implement, so just stub them + * in order to prevent forced unbinding (which deadlocks solid when our + * ->disconnect method waits for the reset to complete and this kills keventd). + * + * XXX Tell Alan to move usb_unlock_device inside of usb_reset_device, + * or else the post_reset is invoked, and restats I/O on a locked device. + */ +static int ub_pre_reset(struct usb_interface *iface) { + return 0; +} + +static int ub_post_reset(struct usb_interface *iface) { + return 0; +} + +/* * This is called from a process context. */ static void ub_revalidate(struct ub_dev *sc, struct ub_lun *lun) @@ -2446,6 +2460,8 @@ static struct usb_driver ub_driver = { .probe = ub_probe, .disconnect = ub_disconnect, .id_table = ub_usb_ids, + .pre_reset = ub_pre_reset, + .post_reset = ub_post_reset, }; static int __init ub_init(void) diff --git a/drivers/char/Kconfig b/drivers/char/Kconfig index 43b35d0..43d6ba8 100644 --- a/drivers/char/Kconfig +++ b/drivers/char/Kconfig @@ -124,7 +124,7 @@ config COMPUTONE which give you many serial ports. You would need something like this to connect more than two modems to your Linux box, for instance in order to become a dial-in server. If you have a card like that, say - Y here and read <file:Documentation/computone.txt>. + Y here and read <file:Documentation/serial/computone.txt>. To compile this driver as module, choose M here: the module will be called ip2. @@ -136,7 +136,7 @@ config ROCKETPORT This driver supports Comtrol RocketPort and RocketModem PCI boards. These boards provide 2, 4, 8, 16, or 32 high-speed serial ports or modems. For information about the RocketPort/RocketModem boards - and this driver read <file:Documentation/rocket.txt>. + and this driver read <file:Documentation/serial/rocket.txt>. To compile this driver as a module, choose M here: the module will be called rocket. @@ -154,7 +154,7 @@ config CYCLADES your Linux box, for instance in order to become a dial-in server. For information about the Cyclades-Z card, read - <file:Documentation/README.cycladesZ>. + <file:Documentation/serial/README.cycladesZ>. To compile this driver as a module, choose M here: the module will be called cyclades. @@ -183,7 +183,7 @@ config DIGIEPCA box, for instance in order to become a dial-in server. This driver supports the original PC (ISA) boards as well as PCI, and EISA. If you have a card like this, say Y here and read the file - <file:Documentation/digiepca.txt>. + <file:Documentation/serial/digiepca.txt>. To compile this driver as a module, choose M here: the module will be called epca. @@ -289,7 +289,7 @@ config RISCOM8 which gives you many serial ports. You would need something like this to connect more than two modems to your Linux box, for instance in order to become a dial-in server. If you have a card like that, - say Y here and read the file <file:Documentation/riscom8.txt>. + say Y here and read the file <file:Documentation/serial/riscom8.txt>. Also it's possible to say M here and compile this driver as kernel loadable module; the module will be called riscom8. @@ -304,8 +304,8 @@ config SPECIALIX your Linux box, for instance in order to become a dial-in server. If you have a card like that, say Y here and read the file - <file:Documentation/specialix.txt>. Also it's possible to say M here - and compile this driver as kernel loadable module which will be + <file:Documentation/serial/specialix.txt>. Also it's possible to say + M here and compile this driver as kernel loadable module which will be called specialix. config SX @@ -313,7 +313,7 @@ config SX depends on SERIAL_NONSTANDARD && (PCI || EISA || ISA) help This is a driver for the SX and SI multiport serial cards. - Please read the file <file:Documentation/sx.txt> for details. + Please read the file <file:Documentation/serial/sx.txt> for details. This driver can only be built as a module ( = code which can be inserted in and removed from the running kernel whenever you want). @@ -344,8 +344,8 @@ config STALDRV like this to connect more than two modems to your Linux box, for instance in order to become a dial-in server. If you say Y here, you will be asked for your specific card model in the next - questions. Make sure to read <file:Documentation/stallion.txt> in - this case. If you have never heard about all this, it's safe to + questions. Make sure to read <file:Documentation/serial/stallion.txt> + in this case. If you have never heard about all this, it's safe to say N. config STALLION @@ -354,7 +354,7 @@ config STALLION help If you have an EasyIO or EasyConnection 8/32 multiport Stallion card, then this is for you; say Y. Make sure to read - <file:Documentation/stallion.txt>. + <file:Documentation/serial/stallion.txt>. To compile this driver as a module, choose M here: the module will be called stallion. @@ -365,7 +365,7 @@ config ISTALLION help If you have an EasyConnection 8/64, ONboard, Brumby or Stallion serial multiport card, say Y here. Make sure to read - <file:Documentation/stallion.txt>. + <file:Documentation/serial/stallion.txt>. To compile this driver as a module, choose M here: the module will be called istallion. diff --git a/drivers/char/specialix.c b/drivers/char/specialix.c index 242fd46..a16b94f 100644 --- a/drivers/char/specialix.c +++ b/drivers/char/specialix.c @@ -72,7 +72,7 @@ /* * There is a bunch of documentation about the card, jumpers, config * settings, restrictions, cables, device names and numbers in - * Documentation/specialix.txt + * Documentation/serial/specialix.txt */ #include <linux/module.h> diff --git a/drivers/hid/hid-apple.c b/drivers/hid/hid-apple.c index c6ab4ba..9b97795 100644 --- a/drivers/hid/hid-apple.c +++ b/drivers/hid/hid-apple.c @@ -55,10 +55,11 @@ struct apple_key_translation { static struct apple_key_translation apple_fn_keys[] = { { KEY_BACKSPACE, KEY_DELETE }, + { KEY_ENTER, KEY_INSERT }, { KEY_F1, KEY_BRIGHTNESSDOWN, APPLE_FLAG_FKEY }, { KEY_F2, KEY_BRIGHTNESSUP, APPLE_FLAG_FKEY }, - { KEY_F3, KEY_FN_F5, APPLE_FLAG_FKEY }, /* Exposé */ - { KEY_F4, KEY_FN_F4, APPLE_FLAG_FKEY }, /* Dashboard */ + { KEY_F3, KEY_SCALE, APPLE_FLAG_FKEY }, + { KEY_F4, KEY_DASHBOARD, APPLE_FLAG_FKEY }, { KEY_F5, KEY_KBDILLUMDOWN, APPLE_FLAG_FKEY }, { KEY_F6, KEY_KBDILLUMUP, APPLE_FLAG_FKEY }, { KEY_F7, KEY_PREVIOUSSONG, APPLE_FLAG_FKEY }, @@ -418,6 +419,12 @@ static const struct hid_device_id apple_devices[] = { .driver_data = APPLE_HAS_FN | APPLE_ISO_KEYBOARD }, { HID_USB_DEVICE(USB_VENDOR_ID_APPLE, USB_DEVICE_ID_APPLE_WELLSPRING2_JIS), .driver_data = APPLE_HAS_FN | APPLE_RDESC_JIS }, + { HID_USB_DEVICE(USB_VENDOR_ID_APPLE, USB_DEVICE_ID_APPLE_WELLSPRING3_ANSI), + .driver_data = APPLE_HAS_FN }, + { HID_USB_DEVICE(USB_VENDOR_ID_APPLE, USB_DEVICE_ID_APPLE_WELLSPRING3_ISO), + .driver_data = APPLE_HAS_FN | APPLE_ISO_KEYBOARD }, + { HID_USB_DEVICE(USB_VENDOR_ID_APPLE, USB_DEVICE_ID_APPLE_WELLSPRING3_JIS), + .driver_data = APPLE_HAS_FN | APPLE_RDESC_JIS }, { HID_USB_DEVICE(USB_VENDOR_ID_APPLE, USB_DEVICE_ID_APPLE_FOUNTAIN_TP_ONLY), .driver_data = APPLE_NUMLOCK_EMULATION | APPLE_HAS_FN }, { HID_USB_DEVICE(USB_VENDOR_ID_APPLE, USB_DEVICE_ID_APPLE_GEYSER1_TP_ONLY), diff --git a/drivers/hid/hid-core.c b/drivers/hid/hid-core.c index d3671b4..147ec59 100644 --- a/drivers/hid/hid-core.c +++ b/drivers/hid/hid-core.c @@ -1250,9 +1250,11 @@ static const struct hid_device_id hid_blacklist[] = { { HID_USB_DEVICE(USB_VENDOR_ID_APPLE, USB_DEVICE_ID_APPLE_WELLSPRING2_ANSI) }, { HID_USB_DEVICE(USB_VENDOR_ID_APPLE, USB_DEVICE_ID_APPLE_WELLSPRING2_ISO) }, { HID_USB_DEVICE(USB_VENDOR_ID_APPLE, USB_DEVICE_ID_APPLE_WELLSPRING2_JIS) }, + { HID_USB_DEVICE(USB_VENDOR_ID_APPLE, USB_DEVICE_ID_APPLE_WELLSPRING3_ANSI) }, + { HID_USB_DEVICE(USB_VENDOR_ID_APPLE, USB_DEVICE_ID_APPLE_WELLSPRING3_ISO) }, + { HID_USB_DEVICE(USB_VENDOR_ID_APPLE, USB_DEVICE_ID_APPLE_WELLSPRING3_JIS) }, { HID_USB_DEVICE(USB_VENDOR_ID_APPLE, USB_DEVICE_ID_APPLE_FOUNTAIN_TP_ONLY) }, { HID_USB_DEVICE(USB_VENDOR_ID_APPLE, USB_DEVICE_ID_APPLE_GEYSER1_TP_ONLY) }, - { HID_USB_DEVICE(USB_VENDOR_ID_AVERMEDIA, USB_DEVICE_ID_AVER_FM_MR800) }, { HID_USB_DEVICE(USB_VENDOR_ID_BELKIN, USB_DEVICE_ID_FLIP_KVM) }, { HID_USB_DEVICE(USB_VENDOR_ID_BRIGHT, USB_DEVICE_ID_BRIGHT_ABNT2) }, { HID_USB_DEVICE(USB_VENDOR_ID_CHERRY, USB_DEVICE_ID_CHERRY_CYMOTION) }, @@ -1265,7 +1267,6 @@ static const struct hid_device_id hid_blacklist[] = { { HID_USB_DEVICE(USB_VENDOR_ID_EZKEY, USB_DEVICE_ID_BTC_8193) }, { HID_USB_DEVICE(USB_VENDOR_ID_GENERIC_13BA, USB_DEVICE_ID_GENERIC_13BA_KBD_MOUSE) }, { HID_USB_DEVICE(USB_VENDOR_ID_GYRATION, USB_DEVICE_ID_GYRATION_REMOTE) }, - { HID_USB_DEVICE(USB_VENDOR_ID_KWORLD, USB_DEVICE_ID_KWORLD_RADIO_FM700) }, { HID_USB_DEVICE(USB_VENDOR_ID_GYRATION, USB_DEVICE_ID_GYRATION_REMOTE_2) }, { HID_USB_DEVICE(USB_VENDOR_ID_LABTEC, USB_DEVICE_ID_LABTEC_WIRELESS_KEYBOARD) }, { HID_USB_DEVICE(USB_VENDOR_ID_LOGITECH, USB_DEVICE_ID_MX3000_RECEIVER) }, @@ -1409,6 +1410,7 @@ static const struct hid_device_id hid_ignore_list[] = { { HID_USB_DEVICE(USB_VENDOR_ID_ALCOR, USB_DEVICE_ID_ALCOR_USBRS232) }, { HID_USB_DEVICE(USB_VENDOR_ID_ASUS, USB_DEVICE_ID_ASUS_LCM)}, { HID_USB_DEVICE(USB_VENDOR_ID_ASUS, USB_DEVICE_ID_ASUS_LCM2)}, + { HID_USB_DEVICE(USB_VENDOR_ID_AVERMEDIA, USB_DEVICE_ID_AVER_FM_MR800) }, { HID_USB_DEVICE(USB_VENDOR_ID_BERKSHIRE, USB_DEVICE_ID_BERKSHIRE_PCWD) }, { HID_USB_DEVICE(USB_VENDOR_ID_CIDC, 0x0103) }, { HID_USB_DEVICE(USB_VENDOR_ID_CYGNAL, USB_DEVICE_ID_CYGNAL_RADIO_SI470X) }, @@ -1486,6 +1488,7 @@ static const struct hid_device_id hid_ignore_list[] = { { HID_USB_DEVICE(USB_VENDOR_ID_GTCO, USB_DEVICE_ID_GTCO_1007) }, { HID_USB_DEVICE(USB_VENDOR_ID_IMATION, USB_DEVICE_ID_DISC_STAKKA) }, { HID_USB_DEVICE(USB_VENDOR_ID_KBGEAR, USB_DEVICE_ID_KBGEAR_JAMSTUDIO) }, + { HID_USB_DEVICE(USB_VENDOR_ID_KWORLD, USB_DEVICE_ID_KWORLD_RADIO_FM700) }, { HID_USB_DEVICE(USB_VENDOR_ID_KYE, USB_DEVICE_ID_KYE_GPEN_560) }, { HID_USB_DEVICE(USB_VENDOR_ID_LD, USB_DEVICE_ID_LD_CASSY) }, { HID_USB_DEVICE(USB_VENDOR_ID_LD, USB_DEVICE_ID_LD_POCKETCASSY) }, @@ -1573,6 +1576,9 @@ static const struct hid_device_id hid_mouse_ignore_list[] = { { HID_USB_DEVICE(USB_VENDOR_ID_APPLE, USB_DEVICE_ID_APPLE_WELLSPRING2_ANSI) }, { HID_USB_DEVICE(USB_VENDOR_ID_APPLE, USB_DEVICE_ID_APPLE_WELLSPRING2_ISO) }, { HID_USB_DEVICE(USB_VENDOR_ID_APPLE, USB_DEVICE_ID_APPLE_WELLSPRING2_JIS) }, + { HID_USB_DEVICE(USB_VENDOR_ID_APPLE, USB_DEVICE_ID_APPLE_WELLSPRING3_ANSI) }, + { HID_USB_DEVICE(USB_VENDOR_ID_APPLE, USB_DEVICE_ID_APPLE_WELLSPRING3_ISO) }, + { HID_USB_DEVICE(USB_VENDOR_ID_APPLE, USB_DEVICE_ID_APPLE_WELLSPRING3_JIS) }, { HID_USB_DEVICE(USB_VENDOR_ID_APPLE, USB_DEVICE_ID_APPLE_FOUNTAIN_TP_ONLY) }, { HID_USB_DEVICE(USB_VENDOR_ID_APPLE, USB_DEVICE_ID_APPLE_GEYSER1_TP_ONLY) }, { } @@ -1730,7 +1736,7 @@ static int __init hid_init(void) goto err_bus; #ifdef CONFIG_HID_COMPAT - hid_compat_wq = create_workqueue("hid_compat"); + hid_compat_wq = create_singlethread_workqueue("hid_compat"); if (!hid_compat_wq) { hidraw_exit(); goto err; diff --git a/drivers/hid/hid-ids.h b/drivers/hid/hid-ids.h index f05bcbb..d70075d 100644 --- a/drivers/hid/hid-ids.h +++ b/drivers/hid/hid-ids.h @@ -82,6 +82,9 @@ #define USB_DEVICE_ID_APPLE_WELLSPRING2_ANSI 0x0230 #define USB_DEVICE_ID_APPLE_WELLSPRING2_ISO 0x0231 #define USB_DEVICE_ID_APPLE_WELLSPRING2_JIS 0x0232 +#define USB_DEVICE_ID_APPLE_WELLSPRING3_ANSI 0x0236 +#define USB_DEVICE_ID_APPLE_WELLSPRING3_ISO 0x0237 +#define USB_DEVICE_ID_APPLE_WELLSPRING3_JIS 0x0238 #define USB_DEVICE_ID_APPLE_FOUNTAIN_TP_ONLY 0x030a #define USB_DEVICE_ID_APPLE_GEYSER1_TP_ONLY 0x030b #define USB_DEVICE_ID_APPLE_ATV_IRCONTROL 0x8241 diff --git a/drivers/hid/hidraw.c b/drivers/hid/hidraw.c index 894d52e..7685ae6 100644 --- a/drivers/hid/hidraw.c +++ b/drivers/hid/hidraw.c @@ -38,7 +38,7 @@ static int hidraw_major; static struct cdev hidraw_cdev; static struct class *hidraw_class; static struct hidraw *hidraw_table[HIDRAW_MAX_DEVICES]; -static DEFINE_SPINLOCK(minors_lock); +static DEFINE_MUTEX(minors_lock); static ssize_t hidraw_read(struct file *file, char __user *buffer, size_t count, loff_t *ppos) { @@ -159,13 +159,13 @@ static int hidraw_open(struct inode *inode, struct file *file) struct hidraw_list *list; int err = 0; - lock_kernel(); if (!(list = kzalloc(sizeof(struct hidraw_list), GFP_KERNEL))) { err = -ENOMEM; goto out; } - spin_lock(&minors_lock); + lock_kernel(); + mutex_lock(&minors_lock); if (!hidraw_table[minor]) { printk(KERN_EMERG "hidraw device with minor %d doesn't exist\n", minor); @@ -180,13 +180,16 @@ static int hidraw_open(struct inode *inode, struct file *file) file->private_data = list; dev = hidraw_table[minor]; - if (!dev->open++) - dev->hid->ll_driver->open(dev->hid); + if (!dev->open++) { + err = dev->hid->ll_driver->open(dev->hid); + if (err < 0) + dev->open--; + } out_unlock: - spin_unlock(&minors_lock); -out: + mutex_unlock(&minors_lock); unlock_kernel(); +out: return err; } @@ -310,7 +313,7 @@ int hidraw_connect(struct hid_device *hid) result = -EINVAL; - spin_lock(&minors_lock); + mutex_lock(&minors_lock); for (minor = 0; minor < HIDRAW_MAX_DEVICES; minor++) { if (hidraw_table[minor]) @@ -320,9 +323,8 @@ int hidraw_connect(struct hid_device *hid) break; } - spin_unlock(&minors_lock); - if (result) { + mutex_unlock(&minors_lock); kfree(dev); goto out; } @@ -331,14 +333,14 @@ int hidraw_connect(struct hid_device *hid) NULL, "%s%d", "hidraw", minor); if (IS_ERR(dev->dev)) { - spin_lock(&minors_lock); hidraw_table[minor] = NULL; - spin_unlock(&minors_lock); + mutex_unlock(&minors_lock); result = PTR_ERR(dev->dev); kfree(dev); goto out; } + mutex_unlock(&minors_lock); init_waitqueue_head(&dev->wait); INIT_LIST_HEAD(&dev->list); @@ -360,9 +362,9 @@ void hidraw_disconnect(struct hid_device *hid) hidraw->exist = 0; - spin_lock(&minors_lock); + mutex_lock(&minors_lock); hidraw_table[hidraw->minor] = NULL; - spin_unlock(&minors_lock); + mutex_unlock(&minors_lock); device_destroy(hidraw_class, MKDEV(hidraw_major, hidraw->minor)); diff --git a/drivers/hid/usbhid/hid-core.c b/drivers/hid/usbhid/hid-core.c index 18e5ddd..d746bf8 100644 --- a/drivers/hid/usbhid/hid-core.c +++ b/drivers/hid/usbhid/hid-core.c @@ -781,6 +781,8 @@ static int usbhid_start(struct hid_device *hid) unsigned int n, insize = 0; int ret; + clear_bit(HID_DISCONNECTED, &usbhid->iofl); + usbhid->bufsize = HID_MIN_BUFFER_SIZE; hid_find_max_report(hid, HID_INPUT_REPORT, &usbhid->bufsize); hid_find_max_report(hid, HID_OUTPUT_REPORT, &usbhid->bufsize); @@ -847,12 +849,6 @@ static int usbhid_start(struct hid_device *hid) } } - if (!usbhid->urbin) { - err_hid("couldn't find an input interrupt endpoint"); - ret = -ENODEV; - goto fail; - } - init_waitqueue_head(&usbhid->wait); INIT_WORK(&usbhid->reset_work, hid_reset); setup_timer(&usbhid->io_retry, hid_retry_timeout, (unsigned long) hid); @@ -888,6 +884,9 @@ fail: usb_free_urb(usbhid->urbin); usb_free_urb(usbhid->urbout); usb_free_urb(usbhid->urbctrl); + usbhid->urbin = NULL; + usbhid->urbout = NULL; + usbhid->urbctrl = NULL; hid_free_buffers(dev, hid); mutex_unlock(&usbhid->setup); return ret; @@ -924,6 +923,9 @@ static void usbhid_stop(struct hid_device *hid) usb_free_urb(usbhid->urbin); usb_free_urb(usbhid->urbctrl); usb_free_urb(usbhid->urbout); + usbhid->urbin = NULL; /* don't mess up next start */ + usbhid->urbctrl = NULL; + usbhid->urbout = NULL; hid_free_buffers(hid_to_usb_dev(hid), hid); mutex_unlock(&usbhid->setup); @@ -940,15 +942,26 @@ static struct hid_ll_driver usb_hid_driver = { static int hid_probe(struct usb_interface *intf, const struct usb_device_id *id) { + struct usb_host_interface *interface = intf->cur_altsetting; struct usb_device *dev = interface_to_usbdev(intf); struct usbhid_device *usbhid; struct hid_device *hid; + unsigned int n, has_in = 0; size_t len; int ret; dbg_hid("HID probe called for ifnum %d\n", intf->altsetting->desc.bInterfaceNumber); + for (n = 0; n < interface->desc.bNumEndpoints; n++) + if (usb_endpoint_is_int_in(&interface->endpoint[n].desc)) + has_in++; + if (!has_in) { + dev_err(&intf->dev, "couldn't find an input interrupt " + "endpoint\n"); + return -ENODEV; + } + hid = hid_allocate_device(); if (IS_ERR(hid)) return PTR_ERR(hid); diff --git a/drivers/hwmon/lis3lv02d.c b/drivers/hwmon/lis3lv02d.c index 752b5c4..c002144 100644 --- a/drivers/hwmon/lis3lv02d.c +++ b/drivers/hwmon/lis3lv02d.c @@ -33,7 +33,6 @@ #include <linux/wait.h> #include <linux/poll.h> #include <linux/freezer.h> -#include <linux/version.h> #include <linux/uaccess.h> #include <acpi/acpi_drivers.h> #include <asm/atomic.h> diff --git a/drivers/i2c/busses/i2c-sh_mobile.c b/drivers/i2c/busses/i2c-sh_mobile.c index 640cbb2..3384a71 100644 --- a/drivers/i2c/busses/i2c-sh_mobile.c +++ b/drivers/i2c/busses/i2c-sh_mobile.c @@ -318,7 +318,8 @@ static int sh_mobile_i2c_isr_rx(struct sh_mobile_i2c_data *pd) } else data = i2c_op(pd, OP_RX, 0); - pd->msg->buf[real_pos] = data; + if (real_pos >= 0) + pd->msg->buf[real_pos] = data; } while (0); pd->pos++; diff --git a/drivers/ide/ide-cs.c b/drivers/ide/ide-cs.c index cb199c8..f50210f 100644 --- a/drivers/ide/ide-cs.c +++ b/drivers/ide/ide-cs.c @@ -444,6 +444,7 @@ static struct pcmcia_device_id ide_ids[] = { PCMCIA_DEVICE_PROD_ID1("STI Flash", 0xe4a13209), PCMCIA_DEVICE_PROD_ID12("STI", "Flash 5.0", 0xbf2df18d, 0x8cb57a0e), PCMCIA_MFC_DEVICE_PROD_ID12(1, "SanDisk", "ConnectPlus", 0x7a954bd9, 0x74be00c6), + PCMCIA_DEVICE_PROD_ID2("Flash Card", 0x5a362506), PCMCIA_DEVICE_NULL, }; MODULE_DEVICE_TABLE(pcmcia, ide_ids); diff --git a/drivers/isdn/i4l/isdn_net.c b/drivers/isdn/i4l/isdn_net.c index bb904a0..1bfc55d 100644 --- a/drivers/isdn/i4l/isdn_net.c +++ b/drivers/isdn/i4l/isdn_net.c @@ -1641,8 +1641,10 @@ isdn_net_ciscohdlck_slarp_send_reply(isdn_net_local *lp) /* slarp reply, send own ip/netmask; if values are nonsense remote * should think we are unable to provide it with an address via SLARP */ p += put_u32(p, CISCO_SLARP_REPLY); - p += put_u32(p, addr); // address - p += put_u32(p, mask); // netmask + *(__be32 *)p = addr; // address + p += 4; + *(__be32 *)p = mask; // netmask + p += 4; p += put_u16(p, 0); // unused isdn_net_write_super(lp, skb); diff --git a/drivers/md/dm-mpath.c b/drivers/md/dm-mpath.c index 4840733..3d7f492 100644 --- a/drivers/md/dm-mpath.c +++ b/drivers/md/dm-mpath.c @@ -441,13 +441,13 @@ static void process_queued_ios(struct work_struct *work) __choose_pgpath(m); pgpath = m->current_pgpath; - m->pgpath_to_activate = m->current_pgpath; if ((pgpath && !m->queue_io) || (!pgpath && !m->queue_if_no_path)) must_queue = 0; - if (m->pg_init_required && !m->pg_init_in_progress) { + if (m->pg_init_required && !m->pg_init_in_progress && pgpath) { + m->pgpath_to_activate = pgpath; m->pg_init_count++; m->pg_init_required = 0; m->pg_init_in_progress = 1; @@ -708,6 +708,10 @@ static int parse_hw_handler(struct arg_set *as, struct multipath *m) m->hw_handler_name = NULL; return -EINVAL; } + + if (hw_argc > 1) + DMWARN("Ignoring user-specified arguments for " + "hardware handler \"%s\"", m->hw_handler_name); consume(as, hw_argc - 1); return 0; diff --git a/drivers/md/dm-raid1.c b/drivers/md/dm-raid1.c index 9d7b53e..ec43f9f 100644 --- a/drivers/md/dm-raid1.c +++ b/drivers/md/dm-raid1.c @@ -1032,6 +1032,7 @@ static void mirror_dtr(struct dm_target *ti) del_timer_sync(&ms->timer); flush_workqueue(ms->kmirrord_wq); + flush_scheduled_work(); dm_kcopyd_client_destroy(ms->kcopyd_client); destroy_workqueue(ms->kmirrord_wq); free_context(ms, ti, ms->nr_mirrors); diff --git a/drivers/md/dm-stripe.c b/drivers/md/dm-stripe.c index a2d068d..9e4ef88 100644 --- a/drivers/md/dm-stripe.c +++ b/drivers/md/dm-stripe.c @@ -320,8 +320,10 @@ int __init dm_stripe_init(void) int r; r = dm_register_target(&stripe_target); - if (r < 0) + if (r < 0) { DMWARN("target registration failed"); + return r; + } kstriped = create_singlethread_workqueue("kstriped"); if (!kstriped) { diff --git a/drivers/md/dm.c b/drivers/md/dm.c index 6963ad1..c99e4728 100644 --- a/drivers/md/dm.c +++ b/drivers/md/dm.c @@ -375,7 +375,7 @@ static void start_io_acct(struct dm_io *io) dm_disk(md)->part0.in_flight = atomic_inc_return(&md->pending); } -static int end_io_acct(struct dm_io *io) +static void end_io_acct(struct dm_io *io) { struct mapped_device *md = io->md; struct bio *bio = io->bio; @@ -391,7 +391,9 @@ static int end_io_acct(struct dm_io *io) dm_disk(md)->part0.in_flight = pending = atomic_dec_return(&md->pending); - return !pending; + /* nudge anyone waiting on suspend queue */ + if (!pending) + wake_up(&md->wait); } /* @@ -499,9 +501,7 @@ static void dec_pending(struct dm_io *io, int error) spin_unlock_irqrestore(&io->md->pushback_lock, flags); } - if (end_io_acct(io)) - /* nudge anyone waiting on suspend queue */ - wake_up(&io->md->wait); + end_io_acct(io); if (io->error != DM_ENDIO_REQUEUE) { blk_add_trace_bio(io->md->queue, io->bio, @@ -937,16 +937,24 @@ static void dm_unplug_all(struct request_queue *q) static int dm_any_congested(void *congested_data, int bdi_bits) { - int r; - struct mapped_device *md = (struct mapped_device *) congested_data; - struct dm_table *map = dm_get_table(md); + int r = bdi_bits; + struct mapped_device *md = congested_data; + struct dm_table *map; - if (!map || test_bit(DMF_BLOCK_IO, &md->flags)) - r = bdi_bits; - else - r = dm_table_any_congested(map, bdi_bits); + atomic_inc(&md->pending); + + if (!test_bit(DMF_BLOCK_IO, &md->flags)) { + map = dm_get_table(md); + if (map) { + r = dm_table_any_congested(map, bdi_bits); + dm_table_put(map); + } + } + + if (!atomic_dec_return(&md->pending)) + /* nudge anyone waiting on suspend queue */ + wake_up(&md->wait); - dm_table_put(map); return r; } diff --git a/drivers/media/video/tvaudio.c b/drivers/media/video/tvaudio.c index b59e472..3720f0e 100644 --- a/drivers/media/video/tvaudio.c +++ b/drivers/media/video/tvaudio.c @@ -1,5 +1,5 @@ /* - * experimental driver for simple i2c audio chips. + * Driver for simple i2c audio chips. * * Copyright (c) 2000 Gerd Knorr * based on code by: @@ -7,6 +7,10 @@ * Steve VanDeBogart (vandebo@uclink.berkeley.edu) * Greg Alexander (galexand@acm.org) * + * Copyright(c) 2005-2008 Mauro Carvalho Chehab + * - Some cleanups, code fixes, etc + * - Convert it to V4L2 API + * * This code is placed under the terms of the GNU General Public License * * OPTIONS: @@ -30,6 +34,7 @@ #include <media/tvaudio.h> #include <media/v4l2-common.h> +#include <media/v4l2-ioctl.h> #include <media/v4l2-chip-ident.h> #include <media/v4l2-i2c-drv-legacy.h> @@ -58,7 +63,6 @@ typedef int (*checkit)(struct CHIPSTATE*); typedef int (*initialize)(struct CHIPSTATE*); typedef int (*getmode)(struct CHIPSTATE*); typedef void (*setmode)(struct CHIPSTATE*, int mode); -typedef void (*checkmode)(struct CHIPSTATE*); /* i2c command */ typedef struct AUDIOCMD { @@ -79,6 +83,7 @@ struct CHIPDESC { #define CHIP_HAS_VOLUME 1 #define CHIP_HAS_BASSTREBLE 2 #define CHIP_HAS_INPUTSEL 4 +#define CHIP_NEED_CHECKMODE 8 /* various i2c command sequences */ audiocmd init; @@ -96,23 +101,20 @@ struct CHIPDESC { getmode getmode; setmode setmode; - /* check / autoswitch audio after channel switches */ - checkmode checkmode; - /* input switch register + values for v4l inputs */ int inputreg; int inputmap[4]; int inputmute; int inputmask; }; -static struct CHIPDESC chiplist[]; /* current state of the chip */ struct CHIPSTATE { struct i2c_client *c; - /* index into CHIPDESC array */ - int type; + /* chip-specific description - should point to + an entry at CHIPDESC table */ + struct CHIPDESC *desc; /* shadow register set */ audiocmd shadow; @@ -152,7 +154,7 @@ static int chip_write(struct CHIPSTATE *chip, int subaddr, int val) { unsigned char buffer[2]; - if (-1 == subaddr) { + if (subaddr < 0) { v4l_dbg(1, debug, chip->c, "%s: chip_write: 0x%x\n", chip->c->name, val); chip->shadow.bytes[1] = val; @@ -163,6 +165,13 @@ static int chip_write(struct CHIPSTATE *chip, int subaddr, int val) return -1; } } else { + if (subaddr + 1 >= ARRAY_SIZE(chip->shadow.bytes)) { + v4l_info(chip->c, + "Tried to access a non-existent register: %d\n", + subaddr); + return -EINVAL; + } + v4l_dbg(1, debug, chip->c, "%s: chip_write: reg%d=0x%x\n", chip->c->name, subaddr, val); chip->shadow.bytes[subaddr+1] = val; @@ -177,12 +186,20 @@ static int chip_write(struct CHIPSTATE *chip, int subaddr, int val) return 0; } -static int chip_write_masked(struct CHIPSTATE *chip, int subaddr, int val, int mask) +static int chip_write_masked(struct CHIPSTATE *chip, + int subaddr, int val, int mask) { if (mask != 0) { - if (-1 == subaddr) { + if (subaddr < 0) { val = (chip->shadow.bytes[1] & ~mask) | (val & mask); } else { + if (subaddr + 1 >= ARRAY_SIZE(chip->shadow.bytes)) { + v4l_info(chip->c, + "Tried to access a non-existent register: %d\n", + subaddr); + return -EINVAL; + } + val = (chip->shadow.bytes[subaddr+1] & ~mask) | (val & mask); } } @@ -228,6 +245,15 @@ static int chip_cmd(struct CHIPSTATE *chip, char *name, audiocmd *cmd) if (0 == cmd->count) return 0; + if (cmd->count + cmd->bytes[0] - 1 >= ARRAY_SIZE(chip->shadow.bytes)) { + v4l_info(chip->c, + "Tried to access a non-existent register range: %d to %d\n", + cmd->bytes[0] + 1, cmd->bytes[0] + cmd->count - 1); + return -EINVAL; + } + + /* FIXME: it seems that the shadow bytes are wrong bellow !*/ + /* update our shadow register set; print bytes if (debug > 0) */ v4l_dbg(1, debug, chip->c, "%s: chip_cmd(%s): reg=%d, data:", chip->c->name, name,cmd->bytes[0]); @@ -263,7 +289,8 @@ static void chip_thread_wake(unsigned long data) static int chip_thread(void *data) { struct CHIPSTATE *chip = data; - struct CHIPDESC *desc = chiplist + chip->type; + struct CHIPDESC *desc = chip->desc; + int mode; v4l_dbg(1, debug, chip->c, "%s: thread started\n", chip->c->name); set_freezable(); @@ -282,7 +309,26 @@ static int chip_thread(void *data) continue; /* have a look what's going on */ - desc->checkmode(chip); + mode = desc->getmode(chip); + if (mode == chip->prevmode) + continue; + + /* chip detected a new audio mode - set it */ + v4l_dbg(1, debug, chip->c, "%s: thread checkmode\n", + chip->c->name); + + chip->prevmode = mode; + + if (mode & V4L2_TUNER_MODE_STEREO) + desc->setmode(chip, V4L2_TUNER_MODE_STEREO); + if (mode & V4L2_TUNER_MODE_LANG1_LANG2) + desc->setmode(chip, V4L2_TUNER_MODE_STEREO); + else if (mode & V4L2_TUNER_MODE_LANG1) + desc->setmode(chip, V4L2_TUNER_MODE_LANG1); + else if (mode & V4L2_TUNER_MODE_LANG2) + desc->setmode(chip, V4L2_TUNER_MODE_LANG2); + else + desc->setmode(chip, V4L2_TUNER_MODE_MONO); /* schedule next check */ mod_timer(&chip->wt, jiffies+msecs_to_jiffies(2000)); @@ -292,29 +338,6 @@ static int chip_thread(void *data) return 0; } -static void generic_checkmode(struct CHIPSTATE *chip) -{ - struct CHIPDESC *desc = chiplist + chip->type; - int mode = desc->getmode(chip); - - if (mode == chip->prevmode) - return; - - v4l_dbg(1, debug, chip->c, "%s: thread checkmode\n", chip->c->name); - chip->prevmode = mode; - - if (mode & V4L2_TUNER_MODE_STEREO) - desc->setmode(chip,V4L2_TUNER_MODE_STEREO); - if (mode & V4L2_TUNER_MODE_LANG1_LANG2) - desc->setmode(chip,V4L2_TUNER_MODE_STEREO); - else if (mode & V4L2_TUNER_MODE_LANG1) - desc->setmode(chip,V4L2_TUNER_MODE_LANG1); - else if (mode & V4L2_TUNER_MODE_LANG2) - desc->setmode(chip,V4L2_TUNER_MODE_LANG2); - else - desc->setmode(chip,V4L2_TUNER_MODE_MONO); -} - /* ---------------------------------------------------------------------- */ /* audio chip descriptions - defines+functions for tda9840 */ @@ -777,7 +800,7 @@ static struct tda9874a_MODES { char *name; audiocmd cmd; } tda9874a_modelist[9] = { - { "A2, B/G", + { "A2, B/G", /* default */ { 9, { TDA9874A_C1FRA, 0x72,0x95,0x55, 0x77,0xA0,0x00, 0x00,0x00 }} }, { "A2, M (Korea)", { 9, { TDA9874A_C1FRA, 0x5D,0xC0,0x00, 0x62,0x6A,0xAA, 0x20,0x22 }} }, @@ -791,7 +814,7 @@ static struct tda9874a_MODES { { 9, { TDA9874A_C1FRA, 0x7D,0x00,0x00, 0x88,0x8A,0xAA, 0x08,0x33 }} }, { "NICAM, B/G", { 9, { TDA9874A_C1FRA, 0x72,0x95,0x55, 0x79,0xEA,0xAA, 0x08,0x33 }} }, - { "NICAM, D/K", /* default */ + { "NICAM, D/K", { 9, { TDA9874A_C1FRA, 0x87,0x6A,0xAA, 0x79,0xEA,0xAA, 0x08,0x33 }} }, { "NICAM, L", { 9, { TDA9874A_C1FRA, 0x87,0x6A,0xAA, 0x79,0xEA,0xAA, 0x09,0x33 }} } @@ -981,7 +1004,7 @@ static int tda9874a_initialize(struct CHIPSTATE *chip) { if (tda9874a_SIF > 2) tda9874a_SIF = 1; - if (tda9874a_STD > 8) + if (tda9874a_STD >= ARRAY_SIZE(tda9874a_modelist)) tda9874a_STD = 0; if(tda9874a_AMSEL > 1) tda9874a_AMSEL = 0; @@ -1089,7 +1112,7 @@ static int tda8425_shift12(int val) { return (val >> 12) | 0xf0; } static int tda8425_initialize(struct CHIPSTATE *chip) { - struct CHIPDESC *desc = chiplist + chip->type; + struct CHIPDESC *desc = chip->desc; int inputmap[4] = { /* tuner */ TDA8425_S1_CH2, /* radio */ TDA8425_S1_CH1, /* extern */ TDA8425_S1_CH1, /* intern */ TDA8425_S1_OFF}; @@ -1259,27 +1282,28 @@ static struct CHIPDESC chiplist[] = { .addr_lo = I2C_ADDR_TDA9840 >> 1, .addr_hi = I2C_ADDR_TDA9840 >> 1, .registers = 5, + .flags = CHIP_NEED_CHECKMODE, + /* callbacks */ .checkit = tda9840_checkit, .getmode = tda9840_getmode, .setmode = tda9840_setmode, - .checkmode = generic_checkmode, .init = { 2, { TDA9840_TEST, TDA9840_TEST_INT1SN /* ,TDA9840_SW, TDA9840_MONO */} } }, { .name = "tda9873h", - .checkit = tda9873_checkit, .insmodopt = &tda9873, .addr_lo = I2C_ADDR_TDA985x_L >> 1, .addr_hi = I2C_ADDR_TDA985x_H >> 1, .registers = 3, - .flags = CHIP_HAS_INPUTSEL, + .flags = CHIP_HAS_INPUTSEL | CHIP_NEED_CHECKMODE, + /* callbacks */ + .checkit = tda9873_checkit, .getmode = tda9873_getmode, .setmode = tda9873_setmode, - .checkmode = generic_checkmode, .init = { 4, { TDA9873_SW, 0xa4, 0x06, 0x03 } }, .inputreg = TDA9873_SW, @@ -1290,15 +1314,16 @@ static struct CHIPDESC chiplist[] = { }, { .name = "tda9874h/a", - .checkit = tda9874a_checkit, - .initialize = tda9874a_initialize, .insmodopt = &tda9874a, .addr_lo = I2C_ADDR_TDA9874 >> 1, .addr_hi = I2C_ADDR_TDA9874 >> 1, + .flags = CHIP_NEED_CHECKMODE, + /* callbacks */ + .initialize = tda9874a_initialize, + .checkit = tda9874a_checkit, .getmode = tda9874a_getmode, .setmode = tda9874a_setmode, - .checkmode = generic_checkmode, }, { .name = "tda9850", @@ -1324,10 +1349,11 @@ static struct CHIPDESC chiplist[] = { .rightreg = TDA9855_VR, .bassreg = TDA9855_BA, .treblereg = TDA9855_TR, + + /* callbacks */ .volfunc = tda9855_volume, .bassfunc = tda9855_bass, .treblefunc = tda9855_treble, - .getmode = tda985x_getmode, .setmode = tda985x_setmode, @@ -1348,6 +1374,8 @@ static struct CHIPDESC chiplist[] = { .rightreg = TEA6300_VL, .bassreg = TEA6300_BA, .treblereg = TEA6300_TR, + + /* callbacks */ .volfunc = tea6300_shift10, .bassfunc = tea6300_shift12, .treblefunc = tea6300_shift12, @@ -1358,7 +1386,6 @@ static struct CHIPDESC chiplist[] = { }, { .name = "tea6320", - .initialize = tea6320_initialize, .insmodopt = &tea6320, .addr_lo = I2C_ADDR_TEA6300 >> 1, .addr_hi = I2C_ADDR_TEA6300 >> 1, @@ -1369,6 +1396,9 @@ static struct CHIPDESC chiplist[] = { .rightreg = TEA6320_V, .bassreg = TEA6320_BA, .treblereg = TEA6320_TR, + + /* callbacks */ + .initialize = tea6320_initialize, .volfunc = tea6320_volume, .bassfunc = tea6320_shift11, .treblefunc = tea6320_shift11, @@ -1401,16 +1431,18 @@ static struct CHIPDESC chiplist[] = { .rightreg = TDA8425_VR, .bassreg = TDA8425_BA, .treblereg = TDA8425_TR, + + /* callbacks */ + .initialize = tda8425_initialize, .volfunc = tda8425_shift10, .bassfunc = tda8425_shift12, .treblefunc = tda8425_shift12, + .setmode = tda8425_setmode, .inputreg = TDA8425_S1, .inputmap = { TDA8425_S1_CH1, TDA8425_S1_CH1, TDA8425_S1_CH1 }, .inputmute = TDA8425_S1_OFF, - .setmode = tda8425_setmode, - .initialize = tda8425_initialize, }, { .name = "pic16c54 (PV951)", @@ -1434,10 +1466,11 @@ static struct CHIPDESC chiplist[] = { .addr_lo = I2C_ADDR_TDA9840 >> 1, .addr_hi = I2C_ADDR_TDA9840 >> 1, .registers = 2, + .flags = CHIP_NEED_CHECKMODE, + /* callbacks */ .getmode = ta8874z_getmode, .setmode = ta8874z_setmode, - .checkmode = generic_checkmode, .init = {2, { TA8874Z_MONO_SET, TA8874Z_SEPARATION_DEFAULT}}, }, @@ -1481,6 +1514,7 @@ static int chip_probe(struct i2c_client *client, const struct i2c_device_id *id) } if (desc->name == NULL) { v4l_dbg(1, debug, client, "no matching chip description found\n"); + kfree(chip); return -EIO; } v4l_info(client, "%s found @ 0x%x (%s)\n", desc->name, client->addr<<1, client->adapter->name); @@ -1494,7 +1528,7 @@ static int chip_probe(struct i2c_client *client, const struct i2c_device_id *id) /* fill required data structures */ if (!id) strlcpy(client->name, desc->name, I2C_NAME_SIZE); - chip->type = desc-chiplist; + chip->desc = desc; chip->shadow.count = desc->registers+1; chip->prevmode = -1; chip->audmode = V4L2_TUNER_MODE_LANG1; @@ -1506,20 +1540,49 @@ static int chip_probe(struct i2c_client *client, const struct i2c_device_id *id) chip_cmd(chip,"init",&desc->init); if (desc->flags & CHIP_HAS_VOLUME) { - chip->left = desc->leftinit ? desc->leftinit : 65535; - chip->right = desc->rightinit ? desc->rightinit : 65535; - chip_write(chip,desc->leftreg,desc->volfunc(chip->left)); - chip_write(chip,desc->rightreg,desc->volfunc(chip->right)); + if (!desc->volfunc) { + /* This shouldn't be happen. Warn user, but keep working + without volume controls + */ + v4l_info(chip->c, "volume callback undefined!\n"); + desc->flags &= ~CHIP_HAS_VOLUME; + } else { + chip->left = desc->leftinit ? desc->leftinit : 65535; + chip->right = desc->rightinit ? desc->rightinit : 65535; + chip_write(chip, desc->leftreg, + desc->volfunc(chip->left)); + chip_write(chip, desc->rightreg, + desc->volfunc(chip->right)); + } } if (desc->flags & CHIP_HAS_BASSTREBLE) { - chip->treble = desc->trebleinit ? desc->trebleinit : 32768; - chip->bass = desc->bassinit ? desc->bassinit : 32768; - chip_write(chip,desc->bassreg,desc->bassfunc(chip->bass)); - chip_write(chip,desc->treblereg,desc->treblefunc(chip->treble)); + if (!desc->bassfunc || !desc->treblefunc) { + /* This shouldn't be happen. Warn user, but keep working + without bass/treble controls + */ + v4l_info(chip->c, "bass/treble callbacks undefined!\n"); + desc->flags &= ~CHIP_HAS_BASSTREBLE; + } else { + chip->treble = desc->trebleinit ? + desc->trebleinit : 32768; + chip->bass = desc->bassinit ? + desc->bassinit : 32768; + chip_write(chip, desc->bassreg, + desc->bassfunc(chip->bass)); + chip_write(chip, desc->treblereg, + desc->treblefunc(chip->treble)); + } } chip->thread = NULL; - if (desc->checkmode) { + if (desc->flags & CHIP_NEED_CHECKMODE) { + if (!desc->getmode || !desc->setmode) { + /* This shouldn't be happen. Warn user, but keep working + without kthread + */ + v4l_info(chip->c, "set/get mode callbacks undefined!\n"); + return 0; + } /* start async thread */ init_timer(&chip->wt); chip->wt.function = chip_thread_wake; @@ -1552,7 +1615,7 @@ static int chip_remove(struct i2c_client *client) static int tvaudio_get_ctrl(struct CHIPSTATE *chip, struct v4l2_control *ctrl) { - struct CHIPDESC *desc = chiplist + chip->type; + struct CHIPDESC *desc = chip->desc; switch (ctrl->id) { case V4L2_CID_AUDIO_MUTE: @@ -1576,13 +1639,13 @@ static int tvaudio_get_ctrl(struct CHIPSTATE *chip, return 0; } case V4L2_CID_AUDIO_BASS: - if (desc->flags & CHIP_HAS_BASSTREBLE) + if (!(desc->flags & CHIP_HAS_BASSTREBLE)) break; ctrl->value = chip->bass; return 0; case V4L2_CID_AUDIO_TREBLE: - if (desc->flags & CHIP_HAS_BASSTREBLE) - return -EINVAL; + if (!(desc->flags & CHIP_HAS_BASSTREBLE)) + break; ctrl->value = chip->treble; return 0; } @@ -1592,7 +1655,7 @@ static int tvaudio_get_ctrl(struct CHIPSTATE *chip, static int tvaudio_set_ctrl(struct CHIPSTATE *chip, struct v4l2_control *ctrl) { - struct CHIPDESC *desc = chiplist + chip->type; + struct CHIPDESC *desc = chip->desc; switch (ctrl->id) { case V4L2_CID_AUDIO_MUTE: @@ -1642,16 +1705,15 @@ static int tvaudio_set_ctrl(struct CHIPSTATE *chip, return 0; } case V4L2_CID_AUDIO_BASS: - if (desc->flags & CHIP_HAS_BASSTREBLE) + if (!(desc->flags & CHIP_HAS_BASSTREBLE)) break; chip->bass = ctrl->value; chip_write(chip,desc->bassreg,desc->bassfunc(chip->bass)); return 0; case V4L2_CID_AUDIO_TREBLE: - if (desc->flags & CHIP_HAS_BASSTREBLE) - return -EINVAL; - + if (!(desc->flags & CHIP_HAS_BASSTREBLE)) + break; chip->treble = ctrl->value; chip_write(chip,desc->treblereg,desc->treblefunc(chip->treble)); @@ -1668,9 +1730,12 @@ static int chip_command(struct i2c_client *client, unsigned int cmd, void *arg) { struct CHIPSTATE *chip = i2c_get_clientdata(client); - struct CHIPDESC *desc = chiplist + chip->type; + struct CHIPDESC *desc = chip->desc; - v4l_dbg(1, debug, chip->c, "%s: chip_command 0x%x\n", chip->c->name, cmd); + if (debug > 0) { + v4l_i2c_print_ioctl(chip->c, cmd); + printk("\n"); + } switch (cmd) { case AUDC_SET_RADIO: @@ -1695,7 +1760,7 @@ static int chip_command(struct i2c_client *client, break; case V4L2_CID_AUDIO_BASS: case V4L2_CID_AUDIO_TREBLE: - if (desc->flags & CHIP_HAS_BASSTREBLE) + if (!(desc->flags & CHIP_HAS_BASSTREBLE)) return -EINVAL; break; default: @@ -1792,12 +1857,20 @@ static int chip_command(struct i2c_client *client, break; case VIDIOC_S_FREQUENCY: chip->mode = 0; /* automatic */ - if (desc->checkmode && desc->setmode) { + + /* For chips that provide getmode and setmode, and doesn't + automatically follows the stereo carrier, a kthread is + created to set the audio standard. In this case, when then + the video channel is changed, tvaudio starts on MONO mode. + After waiting for 2 seconds, the kernel thread is called, + to follow whatever audio standard is pointed by the + audio carrier. + */ + if (chip->thread) { desc->setmode(chip,V4L2_TUNER_MODE_MONO); if (chip->prevmode != V4L2_TUNER_MODE_MONO) chip->prevmode = -1; /* reset previous mode */ mod_timer(&chip->wt, jiffies+msecs_to_jiffies(2000)); - /* the thread will call checkmode() later */ } break; @@ -1836,9 +1909,3 @@ static struct v4l2_i2c_driver_data v4l2_i2c_data = { .legacy_probe = chip_legacy_probe, .id_table = chip_id, }; - -/* - * Local variables: - * c-basic-offset: 8 - * End: - */ diff --git a/drivers/mfd/da903x.c b/drivers/mfd/da903x.c index b57326a..0b5bd85 100644 --- a/drivers/mfd/da903x.c +++ b/drivers/mfd/da903x.c @@ -267,7 +267,7 @@ static int da9030_mask_events(struct da903x_chip *chip, unsigned int events) { uint8_t v[3]; - chip->events_mask &= ~events; + chip->events_mask |= events; v[0] = (chip->events_mask & 0xff); v[1] = (chip->events_mask >> 8) & 0xff; diff --git a/drivers/mfd/wm8350-i2c.c b/drivers/mfd/wm8350-i2c.c index 8dfe21b..3e0ce0e 100644 --- a/drivers/mfd/wm8350-i2c.c +++ b/drivers/mfd/wm8350-i2c.c @@ -30,7 +30,12 @@ static int wm8350_i2c_read_device(struct wm8350 *wm8350, char reg, ret = i2c_master_send(wm8350->i2c_client, ®, 1); if (ret < 0) return ret; - return i2c_master_recv(wm8350->i2c_client, dest, bytes); + ret = i2c_master_recv(wm8350->i2c_client, dest, bytes); + if (ret < 0) + return ret; + if (ret != bytes) + return -EIO; + return 0; } static int wm8350_i2c_write_device(struct wm8350 *wm8350, char reg, @@ -38,13 +43,19 @@ static int wm8350_i2c_write_device(struct wm8350 *wm8350, char reg, { /* we add 1 byte for device register */ u8 msg[(WM8350_MAX_REGISTER << 1) + 1]; + int ret; if (bytes > ((WM8350_MAX_REGISTER << 1) + 1)) return -EINVAL; msg[0] = reg; memcpy(&msg[1], src, bytes); - return i2c_master_send(wm8350->i2c_client, msg, bytes + 1); + ret = i2c_master_send(wm8350->i2c_client, msg, bytes + 1); + if (ret < 0) + return ret; + if (ret != bytes + 1) + return -EIO; + return 0; } static int wm8350_i2c_probe(struct i2c_client *i2c, diff --git a/drivers/misc/c2port/core.c b/drivers/misc/c2port/core.c index 976b35d..0207dd5 100644 --- a/drivers/misc/c2port/core.c +++ b/drivers/misc/c2port/core.c @@ -18,6 +18,7 @@ #include <linux/ctype.h> #include <linux/delay.h> #include <linux/idr.h> +#include <linux/sched.h> #include <linux/c2port.h> diff --git a/drivers/net/atl1e/atl1e_hw.c b/drivers/net/atl1e/atl1e_hw.c index 8cbc1b5..4a77006 100644 --- a/drivers/net/atl1e/atl1e_hw.c +++ b/drivers/net/atl1e/atl1e_hw.c @@ -163,9 +163,6 @@ int atl1e_read_mac_addr(struct atl1e_hw *hw) * atl1e_hash_mc_addr * purpose * set hash value for a multicast address - * hash calcu processing : - * 1. calcu 32bit CRC for multicast address - * 2. reverse crc with MSB to LSB */ u32 atl1e_hash_mc_addr(struct atl1e_hw *hw, u8 *mc_addr) { @@ -174,7 +171,6 @@ u32 atl1e_hash_mc_addr(struct atl1e_hw *hw, u8 *mc_addr) int i; crc32 = ether_crc_le(6, mc_addr); - crc32 = ~crc32; for (i = 0; i < 32; i++) value |= (((crc32 >> i) & 1) << (31 - i)); diff --git a/drivers/net/atlx/atl1.c b/drivers/net/atlx/atl1.c index 246d92b..aef403d 100644 --- a/drivers/net/atlx/atl1.c +++ b/drivers/net/atlx/atl1.c @@ -3404,14 +3404,8 @@ static void atl1_get_wol(struct net_device *netdev, { struct atl1_adapter *adapter = netdev_priv(netdev); - wol->supported = WAKE_UCAST | WAKE_MCAST | WAKE_BCAST | WAKE_MAGIC; + wol->supported = WAKE_MAGIC; wol->wolopts = 0; - if (adapter->wol & ATLX_WUFC_EX) - wol->wolopts |= WAKE_UCAST; - if (adapter->wol & ATLX_WUFC_MC) - wol->wolopts |= WAKE_MCAST; - if (adapter->wol & ATLX_WUFC_BC) - wol->wolopts |= WAKE_BCAST; if (adapter->wol & ATLX_WUFC_MAG) wol->wolopts |= WAKE_MAGIC; return; @@ -3422,15 +3416,10 @@ static int atl1_set_wol(struct net_device *netdev, { struct atl1_adapter *adapter = netdev_priv(netdev); - if (wol->wolopts & (WAKE_PHY | WAKE_ARP | WAKE_MAGICSECURE)) + if (wol->wolopts & (WAKE_PHY | WAKE_UCAST | WAKE_MCAST | WAKE_BCAST | + WAKE_ARP | WAKE_MAGICSECURE)) return -EOPNOTSUPP; adapter->wol = 0; - if (wol->wolopts & WAKE_UCAST) - adapter->wol |= ATLX_WUFC_EX; - if (wol->wolopts & WAKE_MCAST) - adapter->wol |= ATLX_WUFC_MC; - if (wol->wolopts & WAKE_BCAST) - adapter->wol |= ATLX_WUFC_BC; if (wol->wolopts & WAKE_MAGIC) adapter->wol |= ATLX_WUFC_MAG; return 0; diff --git a/drivers/net/e100.c b/drivers/net/e100.c index 3d69fae..e8bfcce 100644 --- a/drivers/net/e100.c +++ b/drivers/net/e100.c @@ -166,7 +166,7 @@ #define DRV_NAME "e100" #define DRV_EXT "-NAPI" -#define DRV_VERSION "3.5.23-k4"DRV_EXT +#define DRV_VERSION "3.5.23-k6"DRV_EXT #define DRV_DESCRIPTION "Intel(R) PRO/100 Network Driver" #define DRV_COPYRIGHT "Copyright(c) 1999-2006 Intel Corporation" #define PFX DRV_NAME ": " @@ -1804,7 +1804,7 @@ static int e100_rx_alloc_skb(struct nic *nic, struct rx *rx) struct rfd *prev_rfd = (struct rfd *)rx->prev->skb->data; put_unaligned_le32(rx->dma_addr, &prev_rfd->link); pci_dma_sync_single_for_device(nic->pdev, rx->prev->dma_addr, - sizeof(struct rfd), PCI_DMA_TODEVICE); + sizeof(struct rfd), PCI_DMA_BIDIRECTIONAL); } return 0; @@ -1823,7 +1823,7 @@ static int e100_rx_indicate(struct nic *nic, struct rx *rx, /* Need to sync before taking a peek at cb_complete bit */ pci_dma_sync_single_for_cpu(nic->pdev, rx->dma_addr, - sizeof(struct rfd), PCI_DMA_FROMDEVICE); + sizeof(struct rfd), PCI_DMA_BIDIRECTIONAL); rfd_status = le16_to_cpu(rfd->status); DPRINTK(RX_STATUS, DEBUG, "status=0x%04X\n", rfd_status); @@ -1850,7 +1850,7 @@ static int e100_rx_indicate(struct nic *nic, struct rx *rx, /* Get data */ pci_unmap_single(nic->pdev, rx->dma_addr, - RFD_BUF_LEN, PCI_DMA_FROMDEVICE); + RFD_BUF_LEN, PCI_DMA_BIDIRECTIONAL); /* If this buffer has the el bit, but we think the receiver * is still running, check to see if it really stopped while @@ -1943,7 +1943,7 @@ static void e100_rx_clean(struct nic *nic, unsigned int *work_done, new_before_last_rfd->command |= cpu_to_le16(cb_el); pci_dma_sync_single_for_device(nic->pdev, new_before_last_rx->dma_addr, sizeof(struct rfd), - PCI_DMA_TODEVICE); + PCI_DMA_BIDIRECTIONAL); /* Now that we have a new stopping point, we can clear the old * stopping point. We must sync twice to get the proper @@ -1951,11 +1951,11 @@ static void e100_rx_clean(struct nic *nic, unsigned int *work_done, old_before_last_rfd->command &= ~cpu_to_le16(cb_el); pci_dma_sync_single_for_device(nic->pdev, old_before_last_rx->dma_addr, sizeof(struct rfd), - PCI_DMA_TODEVICE); + PCI_DMA_BIDIRECTIONAL); old_before_last_rfd->size = cpu_to_le16(VLAN_ETH_FRAME_LEN); pci_dma_sync_single_for_device(nic->pdev, old_before_last_rx->dma_addr, sizeof(struct rfd), - PCI_DMA_TODEVICE); + PCI_DMA_BIDIRECTIONAL); } if(restart_required) { @@ -1978,7 +1978,7 @@ static void e100_rx_clean_list(struct nic *nic) for(rx = nic->rxs, i = 0; i < count; rx++, i++) { if(rx->skb) { pci_unmap_single(nic->pdev, rx->dma_addr, - RFD_BUF_LEN, PCI_DMA_FROMDEVICE); + RFD_BUF_LEN, PCI_DMA_BIDIRECTIONAL); dev_kfree_skb(rx->skb); } } @@ -2021,7 +2021,7 @@ static int e100_rx_alloc_list(struct nic *nic) before_last->command |= cpu_to_le16(cb_el); before_last->size = 0; pci_dma_sync_single_for_device(nic->pdev, rx->dma_addr, - sizeof(struct rfd), PCI_DMA_TODEVICE); + sizeof(struct rfd), PCI_DMA_BIDIRECTIONAL); nic->rx_to_use = nic->rx_to_clean = nic->rxs; nic->ru_running = RU_SUSPENDED; @@ -2222,7 +2222,7 @@ static int e100_loopback_test(struct nic *nic, enum loopback loopback_mode) msleep(10); pci_dma_sync_single_for_cpu(nic->pdev, nic->rx_to_clean->dma_addr, - RFD_BUF_LEN, PCI_DMA_FROMDEVICE); + RFD_BUF_LEN, PCI_DMA_BIDIRECTIONAL); if(memcmp(nic->rx_to_clean->skb->data + sizeof(struct rfd), skb->data, ETH_DATA_LEN)) diff --git a/drivers/net/e1000/e1000_ethtool.c b/drivers/net/e1000/e1000_ethtool.c index 6a3893a..c854c96 100644 --- a/drivers/net/e1000/e1000_ethtool.c +++ b/drivers/net/e1000/e1000_ethtool.c @@ -1774,7 +1774,8 @@ static void e1000_get_wol(struct net_device *netdev, /* this function will set ->supported = 0 and return 1 if wol is not * supported by this hardware */ - if (e1000_wol_exclusion(adapter, wol)) + if (e1000_wol_exclusion(adapter, wol) || + !device_can_wakeup(&adapter->pdev->dev)) return; /* apply any specific unsupported masks here */ @@ -1811,7 +1812,8 @@ static int e1000_set_wol(struct net_device *netdev, struct ethtool_wolinfo *wol) if (wol->wolopts & (WAKE_PHY | WAKE_ARP | WAKE_MAGICSECURE)) return -EOPNOTSUPP; - if (e1000_wol_exclusion(adapter, wol)) + if (e1000_wol_exclusion(adapter, wol) || + !device_can_wakeup(&adapter->pdev->dev)) return wol->wolopts ? -EOPNOTSUPP : 0; switch (hw->device_id) { @@ -1838,6 +1840,8 @@ static int e1000_set_wol(struct net_device *netdev, struct ethtool_wolinfo *wol) if (wol->wolopts & WAKE_MAGIC) adapter->wol |= E1000_WUFC_MAG; + device_set_wakeup_enable(&adapter->pdev->dev, adapter->wol); + return 0; } diff --git a/drivers/net/e1000/e1000_main.c b/drivers/net/e1000/e1000_main.c index fac8215..872799b 100644 --- a/drivers/net/e1000/e1000_main.c +++ b/drivers/net/e1000/e1000_main.c @@ -1179,6 +1179,7 @@ static int __devinit e1000_probe(struct pci_dev *pdev, /* initialize the wol settings based on the eeprom settings */ adapter->wol = adapter->eeprom_wol; + device_set_wakeup_enable(&adapter->pdev->dev, adapter->wol); /* print bus type/speed/width info */ DPRINTK(PROBE, INFO, "(PCI%s:%s:%s) ", diff --git a/drivers/net/e1000e/e1000.h b/drivers/net/e1000e/e1000.h index c55de1c..c55fd6f 100644 --- a/drivers/net/e1000e/e1000.h +++ b/drivers/net/e1000e/e1000.h @@ -299,6 +299,7 @@ struct e1000_adapter { unsigned long led_status; unsigned int flags; + unsigned int flags2; struct work_struct downshift_task; struct work_struct update_phy_task; }; @@ -306,6 +307,7 @@ struct e1000_adapter { struct e1000_info { enum e1000_mac_type mac; unsigned int flags; + unsigned int flags2; u32 pba; s32 (*get_variants)(struct e1000_adapter *); struct e1000_mac_operations *mac_ops; @@ -347,6 +349,9 @@ struct e1000_info { #define FLAG_RX_RESTART_NOW (1 << 30) #define FLAG_MSI_TEST_FAILED (1 << 31) +/* CRC Stripping defines */ +#define FLAG2_CRC_STRIPPING (1 << 0) + #define E1000_RX_DESC_PS(R, i) \ (&(((union e1000_rx_desc_packet_split *)((R).desc))[i])) #define E1000_GET_DESC(R, i, type) (&(((struct type *)((R).desc))[i])) diff --git a/drivers/net/e1000e/ethtool.c b/drivers/net/e1000e/ethtool.c index 70c11c8..62421ce 100644 --- a/drivers/net/e1000e/ethtool.c +++ b/drivers/net/e1000e/ethtool.c @@ -1713,7 +1713,8 @@ static void e1000_get_wol(struct net_device *netdev, wol->supported = 0; wol->wolopts = 0; - if (!(adapter->flags & FLAG_HAS_WOL)) + if (!(adapter->flags & FLAG_HAS_WOL) || + !device_can_wakeup(&adapter->pdev->dev)) return; wol->supported = WAKE_UCAST | WAKE_MCAST | @@ -1751,7 +1752,8 @@ static int e1000_set_wol(struct net_device *netdev, if (wol->wolopts & WAKE_MAGICSECURE) return -EOPNOTSUPP; - if (!(adapter->flags & FLAG_HAS_WOL)) + if (!(adapter->flags & FLAG_HAS_WOL) || + !device_can_wakeup(&adapter->pdev->dev)) return wol->wolopts ? -EOPNOTSUPP : 0; /* these settings will always override what we currently have */ @@ -1770,6 +1772,8 @@ static int e1000_set_wol(struct net_device *netdev, if (wol->wolopts & WAKE_ARP) adapter->wol |= E1000_WUFC_ARP; + device_set_wakeup_enable(&adapter->pdev->dev, adapter->wol); + return 0; } diff --git a/drivers/net/e1000e/netdev.c b/drivers/net/e1000e/netdev.c index abd492b..91795f7 100644 --- a/drivers/net/e1000e/netdev.c +++ b/drivers/net/e1000e/netdev.c @@ -499,6 +499,10 @@ static bool e1000_clean_rx_irq(struct e1000_adapter *adapter, goto next_desc; } + /* adjust length to remove Ethernet CRC */ + if (!(adapter->flags2 & FLAG2_CRC_STRIPPING)) + length -= 4; + total_rx_bytes += length; total_rx_packets++; @@ -804,6 +808,10 @@ static bool e1000_clean_rx_irq_ps(struct e1000_adapter *adapter, pci_dma_sync_single_for_device(pdev, ps_page->dma, PAGE_SIZE, PCI_DMA_FROMDEVICE); + /* remove the CRC */ + if (!(adapter->flags2 & FLAG2_CRC_STRIPPING)) + l1 -= 4; + skb_put(skb, l1); goto copydone; } /* if */ @@ -825,6 +833,12 @@ static bool e1000_clean_rx_irq_ps(struct e1000_adapter *adapter, skb->truesize += length; } + /* strip the ethernet crc, problem is we're using pages now so + * this whole operation can get a little cpu intensive + */ + if (!(adapter->flags2 & FLAG2_CRC_STRIPPING)) + pskb_trim(skb, skb->len - 4); + copydone: total_rx_bytes += skb->len; total_rx_packets++; @@ -2301,8 +2315,12 @@ static void e1000_setup_rctl(struct e1000_adapter *adapter) else rctl |= E1000_RCTL_LPE; - /* Enable hardware CRC frame stripping */ - rctl |= E1000_RCTL_SECRC; + /* Some systems expect that the CRC is included in SMBUS traffic. The + * hardware strips the CRC before sending to both SMBUS (BMC) and to + * host memory when this is enabled + */ + if (adapter->flags2 & FLAG2_CRC_STRIPPING) + rctl |= E1000_RCTL_SECRC; /* Setup buffer sizes */ rctl &= ~E1000_RCTL_SZ_4096; @@ -4766,6 +4784,7 @@ static int __devinit e1000_probe(struct pci_dev *pdev, adapter->ei = ei; adapter->pba = ei->pba; adapter->flags = ei->flags; + adapter->flags2 = ei->flags2; adapter->hw.adapter = adapter; adapter->hw.mac.type = ei->mac; adapter->msg_enable = (1 << NETIF_MSG_DRV | NETIF_MSG_PROBE) - 1; @@ -4970,6 +4989,7 @@ static int __devinit e1000_probe(struct pci_dev *pdev, /* initialize the wol settings based on the eeprom settings */ adapter->wol = adapter->eeprom_wol; + device_set_wakeup_enable(&adapter->pdev->dev, adapter->wol); /* reset the hardware with the new settings */ e1000e_reset(adapter); @@ -5008,6 +5028,7 @@ err_hw_init: err_sw_init: if (adapter->hw.flash_address) iounmap(adapter->hw.flash_address); + e1000e_reset_interrupt_capability(adapter); err_flashmap: iounmap(adapter->hw.hw_addr); err_ioremap: diff --git a/drivers/net/e1000e/param.c b/drivers/net/e1000e/param.c index 77a3d72..e909f96 100644 --- a/drivers/net/e1000e/param.c +++ b/drivers/net/e1000e/param.c @@ -151,6 +151,16 @@ E1000_PARAM(KumeranLockLoss, "Enable Kumeran lock loss workaround"); */ E1000_PARAM(WriteProtectNVM, "Write-protect NVM [WARNING: disabling this can lead to corrupted NVM]"); +/* + * Enable CRC Stripping + * + * Valid Range: 0, 1 + * + * Default Value: 1 (enabled) + */ +E1000_PARAM(CrcStripping, "Enable CRC Stripping, disable if your BMC needs " \ + "the CRC"); + struct e1000_option { enum { enable_option, range_option, list_option } type; const char *name; @@ -404,6 +414,21 @@ void __devinit e1000e_check_options(struct e1000_adapter *adapter) adapter->flags |= FLAG_SMART_POWER_DOWN; } } + { /* CRC Stripping */ + const struct e1000_option opt = { + .type = enable_option, + .name = "CRC Stripping", + .err = "defaulting to enabled", + .def = OPTION_ENABLED + }; + + if (num_CrcStripping > bd) { + unsigned int crc_stripping = CrcStripping[bd]; + e1000_validate_option(&crc_stripping, &opt, adapter); + if (crc_stripping == OPTION_ENABLED) + adapter->flags2 |= FLAG2_CRC_STRIPPING; + } + } { /* Kumeran Lock Loss Workaround */ const struct e1000_option opt = { .type = enable_option, diff --git a/drivers/net/gianfar.c b/drivers/net/gianfar.c index 83a5cb6..c4af949 100644 --- a/drivers/net/gianfar.c +++ b/drivers/net/gianfar.c @@ -1407,6 +1407,10 @@ static int gfar_clean_tx_ring(struct net_device *dev) if (bdp->status & TXBD_DEF) dev->stats.collisions++; + /* Unmap the DMA memory */ + dma_unmap_single(&priv->dev->dev, bdp->bufPtr, + bdp->length, DMA_TO_DEVICE); + /* Free the sk buffer associated with this TxBD */ dev_kfree_skb_irq(priv->tx_skbuff[priv->skb_dirtytx]); @@ -1666,6 +1670,9 @@ int gfar_clean_rx_ring(struct net_device *dev, int rx_work_limit) skb = priv->rx_skbuff[priv->skb_currx]; + dma_unmap_single(&priv->dev->dev, bdp->bufPtr, + priv->rx_buffer_size, DMA_FROM_DEVICE); + /* We drop the frame if we failed to allocate a new buffer */ if (unlikely(!newskb || !(bdp->status & RXBD_LAST) || bdp->status & RXBD_ERR)) { @@ -1674,14 +1681,8 @@ int gfar_clean_rx_ring(struct net_device *dev, int rx_work_limit) if (unlikely(!newskb)) newskb = skb; - if (skb) { - dma_unmap_single(&priv->dev->dev, - bdp->bufPtr, - priv->rx_buffer_size, - DMA_FROM_DEVICE); - + if (skb) dev_kfree_skb_any(skb); - } } else { /* Increment the number of packets */ dev->stats.rx_packets++; diff --git a/drivers/net/igb/igb_ethtool.c b/drivers/net/igb/igb_ethtool.c index 58906c9..89964fa 100644 --- a/drivers/net/igb/igb_ethtool.c +++ b/drivers/net/igb/igb_ethtool.c @@ -1776,7 +1776,8 @@ static void igb_get_wol(struct net_device *netdev, struct ethtool_wolinfo *wol) /* this function will set ->supported = 0 and return 1 if wol is not * supported by this hardware */ - if (igb_wol_exclusion(adapter, wol)) + if (igb_wol_exclusion(adapter, wol) || + !device_can_wakeup(&adapter->pdev->dev)) return; /* apply any specific unsupported masks here */ @@ -1805,7 +1806,8 @@ static int igb_set_wol(struct net_device *netdev, struct ethtool_wolinfo *wol) if (wol->wolopts & (WAKE_PHY | WAKE_ARP | WAKE_MAGICSECURE)) return -EOPNOTSUPP; - if (igb_wol_exclusion(adapter, wol)) + if (igb_wol_exclusion(adapter, wol) || + !device_can_wakeup(&adapter->pdev->dev)) return wol->wolopts ? -EOPNOTSUPP : 0; switch (hw->device_id) { @@ -1825,6 +1827,8 @@ static int igb_set_wol(struct net_device *netdev, struct ethtool_wolinfo *wol) if (wol->wolopts & WAKE_MAGIC) adapter->wol |= E1000_WUFC_MAG; + device_set_wakeup_enable(&adapter->pdev->dev, adapter->wol); + return 0; } diff --git a/drivers/net/igb/igb_main.c b/drivers/net/igb/igb_main.c index 1f397cd..1cbae85 100644 --- a/drivers/net/igb/igb_main.c +++ b/drivers/net/igb/igb_main.c @@ -1019,10 +1019,9 @@ static int __devinit igb_probe(struct pci_dev *pdev, state &= ~PCIE_LINK_STATE_L0S; pci_write_config_word(us_dev, pos + PCI_EXP_LNKCTL, state); - printk(KERN_INFO "Disabling ASPM L0s upstream switch " - "port %x:%x.%x\n", us_dev->bus->number, - PCI_SLOT(us_dev->devfn), - PCI_FUNC(us_dev->devfn)); + dev_info(&pdev->dev, + "Disabling ASPM L0s upstream switch port %s\n", + pci_name(us_dev)); } default: break; @@ -1244,6 +1243,7 @@ static int __devinit igb_probe(struct pci_dev *pdev, /* initialize the wol settings based on the eeprom settings */ adapter->wol = adapter->eeprom_wol; + device_set_wakeup_enable(&adapter->pdev->dev, adapter->wol); /* reset the hardware with the new settings */ igb_reset(adapter); diff --git a/drivers/net/mlx4/en_netdev.c b/drivers/net/mlx4/en_netdev.c index a3f7324..96e709d 100644 --- a/drivers/net/mlx4/en_netdev.c +++ b/drivers/net/mlx4/en_netdev.c @@ -656,10 +656,10 @@ static int mlx4_en_start_port(struct net_device *dev) /* Configure port */ err = mlx4_SET_PORT_general(mdev->dev, priv->port, priv->rx_skb_size + ETH_FCS_LEN, - mdev->profile.tx_pause, - mdev->profile.tx_ppp, - mdev->profile.rx_pause, - mdev->profile.rx_ppp); + priv->prof->tx_pause, + priv->prof->tx_ppp, + priv->prof->rx_pause, + priv->prof->rx_ppp); if (err) { mlx4_err(mdev, "Failed setting port general configurations" " for port %d, with error %d\n", priv->port, err); diff --git a/drivers/net/mlx4/en_params.c b/drivers/net/mlx4/en_params.c index c2e69b1..95706ee 100644 --- a/drivers/net/mlx4/en_params.c +++ b/drivers/net/mlx4/en_params.c @@ -90,6 +90,7 @@ MLX4_EN_PARM_INT(rx_ring_size2, MLX4_EN_AUTO_CONF, "Rx ring size for port 2"); int mlx4_en_get_profile(struct mlx4_en_dev *mdev) { struct mlx4_en_profile *params = &mdev->profile; + int i; params->rx_moder_cnt = min_t(int, rx_moder_cnt, MLX4_EN_AUTO_CONF); params->rx_moder_time = min_t(int, rx_moder_time, MLX4_EN_AUTO_CONF); @@ -97,11 +98,13 @@ int mlx4_en_get_profile(struct mlx4_en_dev *mdev) params->rss_xor = (rss_xor != 0); params->rss_mask = rss_mask & 0x1f; params->num_lro = min_t(int, num_lro , MLX4_EN_MAX_LRO_DESCRIPTORS); - params->rx_pause = pprx; - params->rx_ppp = pfcrx; - params->tx_pause = pptx; - params->tx_ppp = pfctx; - if (params->rx_ppp || params->tx_ppp) { + for (i = 1; i <= MLX4_MAX_PORTS; i++) { + params->prof[i].rx_pause = pprx; + params->prof[i].rx_ppp = pfcrx; + params->prof[i].tx_pause = pptx; + params->prof[i].tx_ppp = pfctx; + } + if (pfcrx || pfctx) { params->prof[1].tx_ring_num = MLX4_EN_TX_RING_NUM; params->prof[2].tx_ring_num = MLX4_EN_TX_RING_NUM; } else { @@ -407,14 +410,14 @@ static int mlx4_en_set_pauseparam(struct net_device *dev, struct mlx4_en_dev *mdev = priv->mdev; int err; - mdev->profile.tx_pause = pause->tx_pause != 0; - mdev->profile.rx_pause = pause->rx_pause != 0; + priv->prof->tx_pause = pause->tx_pause != 0; + priv->prof->rx_pause = pause->rx_pause != 0; err = mlx4_SET_PORT_general(mdev->dev, priv->port, priv->rx_skb_size + ETH_FCS_LEN, - mdev->profile.tx_pause, - mdev->profile.tx_ppp, - mdev->profile.rx_pause, - mdev->profile.rx_ppp); + priv->prof->tx_pause, + priv->prof->tx_ppp, + priv->prof->rx_pause, + priv->prof->rx_ppp); if (err) mlx4_err(mdev, "Failed setting pause params to\n"); @@ -425,10 +428,9 @@ static void mlx4_en_get_pauseparam(struct net_device *dev, struct ethtool_pauseparam *pause) { struct mlx4_en_priv *priv = netdev_priv(dev); - struct mlx4_en_dev *mdev = priv->mdev; - pause->tx_pause = mdev->profile.tx_pause; - pause->rx_pause = mdev->profile.rx_pause; + pause->tx_pause = priv->prof->tx_pause; + pause->rx_pause = priv->prof->rx_pause; } static void mlx4_en_get_ringparam(struct net_device *dev, diff --git a/drivers/net/mlx4/mlx4_en.h b/drivers/net/mlx4/mlx4_en.h index 11fb17c..98ddc08 100644 --- a/drivers/net/mlx4/mlx4_en.h +++ b/drivers/net/mlx4/mlx4_en.h @@ -322,6 +322,10 @@ struct mlx4_en_port_profile { u32 rx_ring_num; u32 tx_ring_size; u32 rx_ring_size; + u8 rx_pause; + u8 rx_ppp; + u8 tx_pause; + u8 tx_ppp; }; struct mlx4_en_profile { @@ -333,10 +337,6 @@ struct mlx4_en_profile { int rx_moder_cnt; int rx_moder_time; int auto_moder; - u8 rx_pause; - u8 rx_ppp; - u8 tx_pause; - u8 tx_ppp; u8 no_reset; struct mlx4_en_port_profile prof[MLX4_MAX_PORTS + 1]; }; diff --git a/drivers/net/niu.c b/drivers/net/niu.c index d8463b1..1b6f548 100644 --- a/drivers/net/niu.c +++ b/drivers/net/niu.c @@ -33,8 +33,8 @@ #define DRV_MODULE_NAME "niu" #define PFX DRV_MODULE_NAME ": " -#define DRV_MODULE_VERSION "0.9" -#define DRV_MODULE_RELDATE "May 4, 2008" +#define DRV_MODULE_VERSION "1.0" +#define DRV_MODULE_RELDATE "Nov 14, 2008" static char version[] __devinitdata = DRV_MODULE_NAME ".c:v" DRV_MODULE_VERSION " (" DRV_MODULE_RELDATE ")\n"; @@ -406,7 +406,7 @@ static int esr2_set_rx_cfg(struct niu *np, unsigned long channel, u32 val) } /* Mode is always 10G fiber. */ -static int serdes_init_niu(struct niu *np) +static int serdes_init_niu_10g_fiber(struct niu *np) { struct niu_link_config *lp = &np->link_config; u32 tx_cfg, rx_cfg; @@ -443,6 +443,223 @@ static int serdes_init_niu(struct niu *np) return 0; } +static int serdes_init_niu_1g_serdes(struct niu *np) +{ + struct niu_link_config *lp = &np->link_config; + u16 pll_cfg, pll_sts; + int max_retry = 100; + u64 sig, mask, val; + u32 tx_cfg, rx_cfg; + unsigned long i; + int err; + + tx_cfg = (PLL_TX_CFG_ENTX | PLL_TX_CFG_SWING_1375MV | + PLL_TX_CFG_RATE_HALF); + rx_cfg = (PLL_RX_CFG_ENRX | PLL_RX_CFG_TERM_0P8VDDT | + PLL_RX_CFG_ALIGN_ENA | PLL_RX_CFG_LOS_LTHRESH | + PLL_RX_CFG_RATE_HALF); + + if (np->port == 0) + rx_cfg |= PLL_RX_CFG_EQ_LP_ADAPTIVE; + + if (lp->loopback_mode == LOOPBACK_PHY) { + u16 test_cfg = PLL_TEST_CFG_LOOPBACK_CML_DIS; + + mdio_write(np, np->port, NIU_ESR2_DEV_ADDR, + ESR2_TI_PLL_TEST_CFG_L, test_cfg); + + tx_cfg |= PLL_TX_CFG_ENTEST; + rx_cfg |= PLL_RX_CFG_ENTEST; + } + + /* Initialize PLL for 1G */ + pll_cfg = (PLL_CFG_ENPLL | PLL_CFG_MPY_8X); + + err = mdio_write(np, np->port, NIU_ESR2_DEV_ADDR, + ESR2_TI_PLL_CFG_L, pll_cfg); + if (err) { + dev_err(np->device, PFX "NIU Port %d " + "serdes_init_niu_1g_serdes: " + "mdio write to ESR2_TI_PLL_CFG_L failed", np->port); + return err; + } + + pll_sts = PLL_CFG_ENPLL; + + err = mdio_write(np, np->port, NIU_ESR2_DEV_ADDR, + ESR2_TI_PLL_STS_L, pll_sts); + if (err) { + dev_err(np->device, PFX "NIU Port %d " + "serdes_init_niu_1g_serdes: " + "mdio write to ESR2_TI_PLL_STS_L failed", np->port); + return err; + } + + udelay(200); + + /* Initialize all 4 lanes of the SERDES. */ + for (i = 0; i < 4; i++) { + err = esr2_set_tx_cfg(np, i, tx_cfg); + if (err) + return err; + } + + for (i = 0; i < 4; i++) { + err = esr2_set_rx_cfg(np, i, rx_cfg); + if (err) + return err; + } + + switch (np->port) { + case 0: + val = (ESR_INT_SRDY0_P0 | ESR_INT_DET0_P0); + mask = val; + break; + + case 1: + val = (ESR_INT_SRDY0_P1 | ESR_INT_DET0_P1); + mask = val; + break; + + default: + return -EINVAL; + } + + while (max_retry--) { + sig = nr64(ESR_INT_SIGNALS); + if ((sig & mask) == val) + break; + + mdelay(500); + } + + if ((sig & mask) != val) { + dev_err(np->device, PFX "Port %u signal bits [%08x] are not " + "[%08x]\n", np->port, (int) (sig & mask), (int) val); + return -ENODEV; + } + + return 0; +} + +static int serdes_init_niu_10g_serdes(struct niu *np) +{ + struct niu_link_config *lp = &np->link_config; + u32 tx_cfg, rx_cfg, pll_cfg, pll_sts; + int max_retry = 100; + u64 sig, mask, val; + unsigned long i; + int err; + + tx_cfg = (PLL_TX_CFG_ENTX | PLL_TX_CFG_SWING_1375MV); + rx_cfg = (PLL_RX_CFG_ENRX | PLL_RX_CFG_TERM_0P8VDDT | + PLL_RX_CFG_ALIGN_ENA | PLL_RX_CFG_LOS_LTHRESH | + PLL_RX_CFG_EQ_LP_ADAPTIVE); + + if (lp->loopback_mode == LOOPBACK_PHY) { + u16 test_cfg = PLL_TEST_CFG_LOOPBACK_CML_DIS; + + mdio_write(np, np->port, NIU_ESR2_DEV_ADDR, + ESR2_TI_PLL_TEST_CFG_L, test_cfg); + + tx_cfg |= PLL_TX_CFG_ENTEST; + rx_cfg |= PLL_RX_CFG_ENTEST; + } + + /* Initialize PLL for 10G */ + pll_cfg = (PLL_CFG_ENPLL | PLL_CFG_MPY_10X); + + err = mdio_write(np, np->port, NIU_ESR2_DEV_ADDR, + ESR2_TI_PLL_CFG_L, pll_cfg & 0xffff); + if (err) { + dev_err(np->device, PFX "NIU Port %d " + "serdes_init_niu_10g_serdes: " + "mdio write to ESR2_TI_PLL_CFG_L failed", np->port); + return err; + } + + pll_sts = PLL_CFG_ENPLL; + + err = mdio_write(np, np->port, NIU_ESR2_DEV_ADDR, + ESR2_TI_PLL_STS_L, pll_sts & 0xffff); + if (err) { + dev_err(np->device, PFX "NIU Port %d " + "serdes_init_niu_10g_serdes: " + "mdio write to ESR2_TI_PLL_STS_L failed", np->port); + return err; + } + + udelay(200); + + /* Initialize all 4 lanes of the SERDES. */ + for (i = 0; i < 4; i++) { + err = esr2_set_tx_cfg(np, i, tx_cfg); + if (err) + return err; + } + + for (i = 0; i < 4; i++) { + err = esr2_set_rx_cfg(np, i, rx_cfg); + if (err) + return err; + } + + /* check if serdes is ready */ + + switch (np->port) { + case 0: + mask = ESR_INT_SIGNALS_P0_BITS; + val = (ESR_INT_SRDY0_P0 | + ESR_INT_DET0_P0 | + ESR_INT_XSRDY_P0 | + ESR_INT_XDP_P0_CH3 | + ESR_INT_XDP_P0_CH2 | + ESR_INT_XDP_P0_CH1 | + ESR_INT_XDP_P0_CH0); + break; + + case 1: + mask = ESR_INT_SIGNALS_P1_BITS; + val = (ESR_INT_SRDY0_P1 | + ESR_INT_DET0_P1 | + ESR_INT_XSRDY_P1 | + ESR_INT_XDP_P1_CH3 | + ESR_INT_XDP_P1_CH2 | + ESR_INT_XDP_P1_CH1 | + ESR_INT_XDP_P1_CH0); + break; + + default: + return -EINVAL; + } + + while (max_retry--) { + sig = nr64(ESR_INT_SIGNALS); + if ((sig & mask) == val) + break; + + mdelay(500); + } + + if ((sig & mask) != val) { + pr_info(PFX "NIU Port %u signal bits [%08x] are not " + "[%08x] for 10G...trying 1G\n", + np->port, (int) (sig & mask), (int) val); + + /* 10G failed, try initializing at 1G */ + err = serdes_init_niu_1g_serdes(np); + if (!err) { + np->flags &= ~NIU_FLAGS_10G; + np->mac_xcvr = MAC_XCVR_PCS; + } else { + dev_err(np->device, PFX "Port %u 10G/1G SERDES " + "Link Failed \n", np->port); + return -ENODEV; + } + } + return 0; +} + static int esr_read_rxtx_ctrl(struct niu *np, unsigned long chan, u32 *val) { int err; @@ -1954,13 +2171,23 @@ static const struct niu_phy_ops phy_ops_10g_serdes = { .link_status = link_status_10g_serdes, }; +static const struct niu_phy_ops phy_ops_10g_serdes_niu = { + .serdes_init = serdes_init_niu_10g_serdes, + .link_status = link_status_10g_serdes, +}; + +static const struct niu_phy_ops phy_ops_1g_serdes_niu = { + .serdes_init = serdes_init_niu_1g_serdes, + .link_status = link_status_1g_serdes, +}; + static const struct niu_phy_ops phy_ops_1g_rgmii = { .xcvr_init = xcvr_init_1g_rgmii, .link_status = link_status_1g_rgmii, }; static const struct niu_phy_ops phy_ops_10g_fiber_niu = { - .serdes_init = serdes_init_niu, + .serdes_init = serdes_init_niu_10g_fiber, .xcvr_init = xcvr_init_10g, .link_status = link_status_10g, }; @@ -1998,11 +2225,21 @@ struct niu_phy_template { u32 phy_addr_base; }; -static const struct niu_phy_template phy_template_niu = { +static const struct niu_phy_template phy_template_niu_10g_fiber = { .ops = &phy_ops_10g_fiber_niu, .phy_addr_base = 16, }; +static const struct niu_phy_template phy_template_niu_10g_serdes = { + .ops = &phy_ops_10g_serdes_niu, + .phy_addr_base = 0, +}; + +static const struct niu_phy_template phy_template_niu_1g_serdes = { + .ops = &phy_ops_1g_serdes_niu, + .phy_addr_base = 0, +}; + static const struct niu_phy_template phy_template_10g_fiber = { .ops = &phy_ops_10g_fiber, .phy_addr_base = 8, @@ -2182,8 +2419,25 @@ static int niu_determine_phy_disposition(struct niu *np) u32 phy_addr_off = 0; if (plat_type == PLAT_TYPE_NIU) { - tp = &phy_template_niu; - phy_addr_off += np->port; + switch (np->flags & + (NIU_FLAGS_10G | + NIU_FLAGS_FIBER | + NIU_FLAGS_XCVR_SERDES)) { + case NIU_FLAGS_10G | NIU_FLAGS_XCVR_SERDES: + /* 10G Serdes */ + tp = &phy_template_niu_10g_serdes; + break; + case NIU_FLAGS_XCVR_SERDES: + /* 1G Serdes */ + tp = &phy_template_niu_1g_serdes; + break; + case NIU_FLAGS_10G | NIU_FLAGS_FIBER: + /* 10G Fiber */ + default: + tp = &phy_template_niu_10g_fiber; + phy_addr_off += np->port; + break; + } } else { switch (np->flags & (NIU_FLAGS_10G | @@ -7213,6 +7467,12 @@ static int __devinit niu_phy_type_prop_decode(struct niu *np, np->flags |= NIU_FLAGS_10G; np->flags &= ~NIU_FLAGS_FIBER; np->mac_xcvr = MAC_XCVR_XPCS; + } else if (!strcmp(phy_prop, "xgsd") || !strcmp(phy_prop, "gsd")) { + /* 10G Serdes or 1G Serdes, default to 10G */ + np->flags |= NIU_FLAGS_10G; + np->flags &= ~NIU_FLAGS_FIBER; + np->flags |= NIU_FLAGS_XCVR_SERDES; + np->mac_xcvr = MAC_XCVR_XPCS; } else { return -EINVAL; } @@ -7741,6 +8001,8 @@ static int __devinit walk_phys(struct niu *np, struct niu_parent *parent) u32 val; int err; + num_10g = num_1g = 0; + if (!strcmp(np->vpd.model, NIU_ALONSO_MDL_STR) || !strcmp(np->vpd.model, NIU_KIMI_MDL_STR)) { num_10g = 0; @@ -7757,6 +8019,16 @@ static int __devinit walk_phys(struct niu *np, struct niu_parent *parent) parent->num_ports = 2; val = (phy_encode(PORT_TYPE_10G, 0) | phy_encode(PORT_TYPE_10G, 1)); + } else if ((np->flags & NIU_FLAGS_XCVR_SERDES) && + (parent->plat_type == PLAT_TYPE_NIU)) { + /* this is the Monza case */ + if (np->flags & NIU_FLAGS_10G) { + val = (phy_encode(PORT_TYPE_10G, 0) | + phy_encode(PORT_TYPE_10G, 1)); + } else { + val = (phy_encode(PORT_TYPE_1G, 0) | + phy_encode(PORT_TYPE_1G, 1)); + } } else { err = fill_phy_probe_info(np, parent, info); if (err) @@ -8656,7 +8928,9 @@ static void __devinit niu_device_announce(struct niu *np) dev->name, (np->flags & NIU_FLAGS_XMAC ? "XMAC" : "BMAC"), (np->flags & NIU_FLAGS_10G ? "10G" : "1G"), - (np->flags & NIU_FLAGS_FIBER ? "FIBER" : "COPPER"), + (np->flags & NIU_FLAGS_FIBER ? "FIBER" : + (np->flags & NIU_FLAGS_XCVR_SERDES ? "SERDES" : + "COPPER")), (np->mac_xcvr == MAC_XCVR_MII ? "MII" : (np->mac_xcvr == MAC_XCVR_PCS ? "PCS" : "XPCS")), np->vpd.phy_type); diff --git a/drivers/net/niu.h b/drivers/net/niu.h index c6fa883..180ca8a 100644 --- a/drivers/net/niu.h +++ b/drivers/net/niu.h @@ -1048,6 +1048,13 @@ #define PLL_CFG_LD_SHIFT 8 #define PLL_CFG_MPY 0x0000001e #define PLL_CFG_MPY_SHIFT 1 +#define PLL_CFG_MPY_4X 0x0 +#define PLL_CFG_MPY_5X 0x00000002 +#define PLL_CFG_MPY_6X 0x00000004 +#define PLL_CFG_MPY_8X 0x00000008 +#define PLL_CFG_MPY_10X 0x0000000a +#define PLL_CFG_MPY_12X 0x0000000c +#define PLL_CFG_MPY_12P5X 0x0000000e #define PLL_CFG_ENPLL 0x00000001 #define ESR2_TI_PLL_STS_L (ESR2_BASE + 0x002) @@ -1093,6 +1100,9 @@ #define PLL_TX_CFG_INVPAIR 0x00000080 #define PLL_TX_CFG_RATE 0x00000060 #define PLL_TX_CFG_RATE_SHIFT 5 +#define PLL_TX_CFG_RATE_FULL 0x0 +#define PLL_TX_CFG_RATE_HALF 0x20 +#define PLL_TX_CFG_RATE_QUAD 0x40 #define PLL_TX_CFG_BUSWIDTH 0x0000001c #define PLL_TX_CFG_BUSWIDTH_SHIFT 2 #define PLL_TX_CFG_ENTEST 0x00000002 @@ -1132,6 +1142,9 @@ #define PLL_RX_CFG_INVPAIR 0x00000080 #define PLL_RX_CFG_RATE 0x00000060 #define PLL_RX_CFG_RATE_SHIFT 5 +#define PLL_RX_CFG_RATE_FULL 0x0 +#define PLL_RX_CFG_RATE_HALF 0x20 +#define PLL_RX_CFG_RATE_QUAD 0x40 #define PLL_RX_CFG_BUSWIDTH 0x0000001c #define PLL_RX_CFG_BUSWIDTH_SHIFT 2 #define PLL_RX_CFG_ENTEST 0x00000002 diff --git a/drivers/net/phy/marvell.c b/drivers/net/phy/marvell.c index 4aa5479..eb6411c 100644 --- a/drivers/net/phy/marvell.c +++ b/drivers/net/phy/marvell.c @@ -227,6 +227,59 @@ static int m88e1111_config_init(struct phy_device *phydev) return 0; } +static int m88e1118_config_aneg(struct phy_device *phydev) +{ + int err; + + err = phy_write(phydev, MII_BMCR, BMCR_RESET); + if (err < 0) + return err; + + err = phy_write(phydev, MII_M1011_PHY_SCR, + MII_M1011_PHY_SCR_AUTO_CROSS); + if (err < 0) + return err; + + err = genphy_config_aneg(phydev); + return 0; +} + +static int m88e1118_config_init(struct phy_device *phydev) +{ + int err; + + /* Change address */ + err = phy_write(phydev, 0x16, 0x0002); + if (err < 0) + return err; + + /* Enable 1000 Mbit */ + err = phy_write(phydev, 0x15, 0x1070); + if (err < 0) + return err; + + /* Change address */ + err = phy_write(phydev, 0x16, 0x0003); + if (err < 0) + return err; + + /* Adjust LED Control */ + err = phy_write(phydev, 0x10, 0x021e); + if (err < 0) + return err; + + /* Reset address */ + err = phy_write(phydev, 0x16, 0x0); + if (err < 0) + return err; + + err = phy_write(phydev, MII_BMCR, BMCR_RESET); + if (err < 0) + return err; + + return 0; +} + static int m88e1145_config_init(struct phy_device *phydev) { int err; @@ -416,6 +469,19 @@ static struct phy_driver marvell_drivers[] = { .driver = { .owner = THIS_MODULE }, }, { + .phy_id = 0x01410e10, + .phy_id_mask = 0xfffffff0, + .name = "Marvell 88E1118", + .features = PHY_GBIT_FEATURES, + .flags = PHY_HAS_INTERRUPT, + .config_init = &m88e1118_config_init, + .config_aneg = &m88e1118_config_aneg, + .read_status = &genphy_read_status, + .ack_interrupt = &marvell_ack_interrupt, + .config_intr = &marvell_config_intr, + .driver = {.owner = THIS_MODULE,}, + }, + { .phy_id = 0x01410cd0, .phy_id_mask = 0xfffffff0, .name = "Marvell 88E1145", diff --git a/drivers/net/phy/mdio_bus.c b/drivers/net/phy/mdio_bus.c index d0ed1ef..536bda1 100644 --- a/drivers/net/phy/mdio_bus.c +++ b/drivers/net/phy/mdio_bus.c @@ -136,7 +136,7 @@ void mdiobus_unregister(struct mii_bus *bus) BUG_ON(bus->state != MDIOBUS_REGISTERED); bus->state = MDIOBUS_UNREGISTERED; - device_unregister(&bus->dev); + device_del(&bus->dev); for (i = 0; i < PHY_MAX_ADDR; i++) { if (bus->phy_map[i]) device_unregister(&bus->phy_map[i]->dev); diff --git a/drivers/net/phy/phy_device.c b/drivers/net/phy/phy_device.c index e11b03b..8fb1fac 100644 --- a/drivers/net/phy/phy_device.c +++ b/drivers/net/phy/phy_device.c @@ -227,8 +227,8 @@ struct phy_device * get_phy_device(struct mii_bus *bus, int addr) if (r) return ERR_PTR(r); - /* If the phy_id is all Fs, there is no device there */ - if (0xffffffff == phy_id) + /* If the phy_id is all Fs or all 0s, there is no device there */ + if ((0xffff == phy_id) || (0x00 == phy_id)) return NULL; dev = phy_device_create(bus, addr, phy_id); diff --git a/drivers/net/qla3xxx.c b/drivers/net/qla3xxx.c index 3cdd07c..508452c 100644 --- a/drivers/net/qla3xxx.c +++ b/drivers/net/qla3xxx.c @@ -1515,9 +1515,6 @@ static u32 ql_get_link_state(struct ql3_adapter *qdev) linkState = LS_UP; } else { linkState = LS_DOWN; - if (netif_msg_link(qdev)) - printk(KERN_WARNING PFX - "%s: Link is down.\n", qdev->ndev->name); } return linkState; } @@ -1581,10 +1578,6 @@ static int ql_finish_auto_neg(struct ql3_adapter *qdev) ql_mac_enable(qdev, 1); } - if (netif_msg_link(qdev)) - printk(KERN_DEBUG PFX - "%s: Change port_link_state LS_DOWN to LS_UP.\n", - qdev->ndev->name); qdev->port_link_state = LS_UP; netif_start_queue(qdev->ndev); netif_carrier_on(qdev->ndev); @@ -1655,14 +1648,9 @@ static void ql_link_state_machine_work(struct work_struct *work) /* Fall Through */ case LS_DOWN: - if (netif_msg_link(qdev)) - printk(KERN_DEBUG PFX - "%s: port_link_state = LS_DOWN.\n", - qdev->ndev->name); if (curr_link_state == LS_UP) { if (netif_msg_link(qdev)) - printk(KERN_DEBUG PFX - "%s: curr_link_state = LS_UP.\n", + printk(KERN_INFO PFX "%s: Link is up.\n", qdev->ndev->name); if (ql_is_auto_neg_complete(qdev)) ql_finish_auto_neg(qdev); @@ -1670,6 +1658,7 @@ static void ql_link_state_machine_work(struct work_struct *work) if (qdev->port_link_state == LS_UP) ql_link_down_detect_clear(qdev); + qdev->port_link_state = LS_UP; } break; @@ -1678,12 +1667,14 @@ static void ql_link_state_machine_work(struct work_struct *work) * See if the link is currently down or went down and came * back up */ - if ((curr_link_state == LS_DOWN) || ql_link_down_detect(qdev)) { + if (curr_link_state == LS_DOWN) { if (netif_msg_link(qdev)) printk(KERN_INFO PFX "%s: Link is down.\n", qdev->ndev->name); qdev->port_link_state = LS_DOWN; } + if (ql_link_down_detect(qdev)) + qdev->port_link_state = LS_DOWN; break; } spin_unlock_irqrestore(&qdev->hw_lock, hw_flags); diff --git a/drivers/net/ucc_geth_ethtool.c b/drivers/net/ucc_geth_ethtool.c index 85f38a6b..68a7f54 100644 --- a/drivers/net/ucc_geth_ethtool.c +++ b/drivers/net/ucc_geth_ethtool.c @@ -323,17 +323,17 @@ static void uec_get_ethtool_stats(struct net_device *netdev, if (stats_mode & UCC_GETH_STATISTICS_GATHERING_MODE_HARDWARE) { base = (u32 __iomem *)&ugeth->ug_regs->tx64; for (i = 0; i < UEC_HW_STATS_LEN; i++) - data[j++] = (u64)in_be32(&base[i]); + data[j++] = in_be32(&base[i]); } if (stats_mode & UCC_GETH_STATISTICS_GATHERING_MODE_FIRMWARE_TX) { base = (u32 __iomem *)ugeth->p_tx_fw_statistics_pram; for (i = 0; i < UEC_TX_FW_STATS_LEN; i++) - data[j++] = (u64)in_be32(&base[i]); + data[j++] = base ? in_be32(&base[i]) : 0; } if (stats_mode & UCC_GETH_STATISTICS_GATHERING_MODE_FIRMWARE_RX) { base = (u32 __iomem *)ugeth->p_rx_fw_statistics_pram; for (i = 0; i < UEC_RX_FW_STATS_LEN; i++) - data[j++] = (u64)in_be32(&base[i]); + data[j++] = base ? in_be32(&base[i]) : 0; } } diff --git a/drivers/net/usb/asix.c b/drivers/net/usb/asix.c index 37ecf84..e12cdb4 100644 --- a/drivers/net/usb/asix.c +++ b/drivers/net/usb/asix.c @@ -1444,6 +1444,10 @@ static const struct usb_device_id products [] = { // Apple USB Ethernet Adapter USB_DEVICE(0x05ac, 0x1402), .driver_info = (unsigned long) &ax88772_info, +}, { + // Cables-to-Go USB Ethernet Adapter + USB_DEVICE(0x0b95, 0x772a), + .driver_info = (unsigned long) &ax88772_info, }, { }, // END }; diff --git a/drivers/net/via-velocity.c b/drivers/net/via-velocity.c index 3590ea5..11cb3e5 100644 --- a/drivers/net/via-velocity.c +++ b/drivers/net/via-velocity.c @@ -2296,7 +2296,7 @@ static void velocity_set_multi(struct net_device *dev) } mac_set_cam_mask(regs, vptr->mCAMmask); - rx_mode = (RCR_AM | RCR_AB); + rx_mode = RCR_AM | RCR_AB | RCR_AP; } if (dev->mtu > 1500) rx_mode |= RCR_AL; diff --git a/drivers/pcmcia/cistpl.c b/drivers/pcmcia/cistpl.c index dcce9f5..4a110b7 100644 --- a/drivers/pcmcia/cistpl.c +++ b/drivers/pcmcia/cistpl.c @@ -351,10 +351,11 @@ int verify_cis_cache(struct pcmcia_socket *s) char *buf; buf = kmalloc(256, GFP_KERNEL); - if (buf == NULL) + if (buf == NULL) { dev_printk(KERN_WARNING, &s->dev, "no memory for verifying CIS\n"); return -ENOMEM; + } list_for_each_entry(cis, &s->cis_cache, node) { int len = cis->len; diff --git a/drivers/pcmcia/cs.c b/drivers/pcmcia/cs.c index c68c5d3..0660ad1 100644 --- a/drivers/pcmcia/cs.c +++ b/drivers/pcmcia/cs.c @@ -186,12 +186,6 @@ int pcmcia_register_socket(struct pcmcia_socket *socket) spin_lock_init(&socket->lock); - if (socket->resource_ops->init) { - ret = socket->resource_ops->init(socket); - if (ret) - return (ret); - } - /* try to obtain a socket number [yes, it gets ugly if we * register more than 2^sizeof(unsigned int) pcmcia * sockets... but the socket number is deprecated @@ -226,7 +220,7 @@ int pcmcia_register_socket(struct pcmcia_socket *socket) /* set proper values in socket->dev */ dev_set_drvdata(&socket->dev, socket); socket->dev.class = &pcmcia_socket_class; - snprintf(socket->dev.bus_id, BUS_ID_SIZE, "pcmcia_socket%u", socket->sock); + dev_set_name(&socket->dev, "pcmcia_socket%u", socket->sock); /* base address = 0, map = 0 */ socket->cis_mem.flags = 0; @@ -239,6 +233,12 @@ int pcmcia_register_socket(struct pcmcia_socket *socket) mutex_init(&socket->skt_mutex); spin_lock_init(&socket->thread_lock); + if (socket->resource_ops->init) { + ret = socket->resource_ops->init(socket); + if (ret) + goto err; + } + tsk = kthread_run(pccardd, socket, "pccardd"); if (IS_ERR(tsk)) { ret = PTR_ERR(tsk); diff --git a/drivers/pcmcia/ds.c b/drivers/pcmcia/ds.c index 7956602..47cab31 100644 --- a/drivers/pcmcia/ds.c +++ b/drivers/pcmcia/ds.c @@ -622,7 +622,6 @@ struct pcmcia_device * pcmcia_device_add(struct pcmcia_socket *s, unsigned int f { struct pcmcia_device *p_dev, *tmp_dev; unsigned long flags; - int bus_id_len; s = pcmcia_get_socket(s); if (!s) @@ -650,12 +649,12 @@ struct pcmcia_device * pcmcia_device_add(struct pcmcia_socket *s, unsigned int f /* by default don't allow DMA */ p_dev->dma_mask = DMA_MASK_NONE; p_dev->dev.dma_mask = &p_dev->dma_mask; - bus_id_len = sprintf (p_dev->dev.bus_id, "%d.%d", p_dev->socket->sock, p_dev->device_no); - - p_dev->devname = kmalloc(6 + bus_id_len + 1, GFP_KERNEL); + dev_set_name(&p_dev->dev, "%d.%d", p_dev->socket->sock, p_dev->device_no); + if (!dev_name(&p_dev->dev)) + goto err_free; + p_dev->devname = kasprintf(GFP_KERNEL, "pcmcia%s", dev_name(&p_dev->dev)); if (!p_dev->devname) goto err_free; - sprintf (p_dev->devname, "pcmcia%s", p_dev->dev.bus_id); ds_dev_dbg(3, &p_dev->dev, "devname is %s\n", p_dev->devname); spin_lock_irqsave(&pcmcia_dev_list_lock, flags); @@ -668,6 +667,8 @@ struct pcmcia_device * pcmcia_device_add(struct pcmcia_socket *s, unsigned int f list_for_each_entry(tmp_dev, &s->devices_list, socket_device_list) if (p_dev->func == tmp_dev->func) { p_dev->function_config = tmp_dev->function_config; + p_dev->io = tmp_dev->io; + p_dev->irq = tmp_dev->irq; kref_get(&p_dev->function_config->ref); } diff --git a/drivers/pcmcia/pcmcia_resource.c b/drivers/pcmcia/pcmcia_resource.c index 76d4a98..f5d0ba8 100644 --- a/drivers/pcmcia/pcmcia_resource.c +++ b/drivers/pcmcia/pcmcia_resource.c @@ -302,9 +302,10 @@ int pcmcia_modify_configuration(struct pcmcia_device *p_dev, /* We only allow changing Vpp1 and Vpp2 to the same value */ if ((mod->Attributes & CONF_VPP1_CHANGE_VALID) && (mod->Attributes & CONF_VPP2_CHANGE_VALID)) { - if (mod->Vpp1 != mod->Vpp2) + if (mod->Vpp1 != mod->Vpp2) { ds_dbg(s, 0, "Vpp1 and Vpp2 must be the same\n"); return -EINVAL; + } s->socket.Vpp = mod->Vpp1; if (s->ops->set_socket(s, &s->socket)) { dev_printk(KERN_WARNING, &s->dev, diff --git a/drivers/pcmcia/rsrc_nonstatic.c b/drivers/pcmcia/rsrc_nonstatic.c index 17f4ecf..9ca22c7 100644 --- a/drivers/pcmcia/rsrc_nonstatic.c +++ b/drivers/pcmcia/rsrc_nonstatic.c @@ -71,7 +71,7 @@ static DEFINE_MUTEX(rsrc_mutex); ======================================================================*/ static struct resource * -make_resource(resource_size_t b, resource_size_t n, int flags, char *name) +make_resource(resource_size_t b, resource_size_t n, int flags, const char *name) { struct resource *res = kzalloc(sizeof(*res), GFP_KERNEL); @@ -624,7 +624,7 @@ static int nonstatic_adjust_io_region(struct resource *res, unsigned long r_star static struct resource *nonstatic_find_io_region(unsigned long base, int num, unsigned long align, struct pcmcia_socket *s) { - struct resource *res = make_resource(0, num, IORESOURCE_IO, s->dev.bus_id); + struct resource *res = make_resource(0, num, IORESOURCE_IO, dev_name(&s->dev)); struct socket_data *s_data = s->resource_data; struct pcmcia_align_data data; unsigned long min = base; @@ -658,7 +658,7 @@ static struct resource *nonstatic_find_io_region(unsigned long base, int num, static struct resource * nonstatic_find_mem_region(u_long base, u_long num, u_long align, int low, struct pcmcia_socket *s) { - struct resource *res = make_resource(0, num, IORESOURCE_MEM, s->dev.bus_id); + struct resource *res = make_resource(0, num, IORESOURCE_MEM, dev_name(&s->dev)); struct socket_data *s_data = s->resource_data; struct pcmcia_align_data data; unsigned long min, max; diff --git a/drivers/rtc/rtc-sun4v.c b/drivers/rtc/rtc-sun4v.c index 2012ccb..5b22610 100644 --- a/drivers/rtc/rtc-sun4v.c +++ b/drivers/rtc/rtc-sun4v.c @@ -1,4 +1,4 @@ -/* rtc-sun4c.c: Hypervisor based RTC for SUN4V systems. +/* rtc-sun4v.c: Hypervisor based RTC for SUN4V systems. * * Copyright (C) 2008 David S. Miller <davem@davemloft.net> */ @@ -7,21 +7,11 @@ #include <linux/module.h> #include <linux/delay.h> #include <linux/init.h> -#include <linux/time.h> #include <linux/rtc.h> #include <linux/platform_device.h> #include <asm/hypervisor.h> -MODULE_AUTHOR("David S. Miller <davem@davemloft.net>"); -MODULE_DESCRIPTION("SUN4V RTC driver"); -MODULE_LICENSE("GPL"); - -struct sun4v_rtc { - struct rtc_device *rtc; - spinlock_t lock; -}; - static unsigned long hypervisor_get_time(void) { unsigned long ret, time; @@ -45,15 +35,7 @@ retry: static int sun4v_read_time(struct device *dev, struct rtc_time *tm) { - struct sun4v_rtc *p = dev_get_drvdata(dev); - unsigned long flags, secs; - - spin_lock_irqsave(&p->lock, flags); - secs = hypervisor_get_time(); - spin_unlock_irqrestore(&p->lock, flags); - - rtc_time_to_tm(secs, tm); - + rtc_time_to_tm(hypervisor_get_time(), tm); return 0; } @@ -80,19 +62,14 @@ retry: static int sun4v_set_time(struct device *dev, struct rtc_time *tm) { - struct sun4v_rtc *p = dev_get_drvdata(dev); - unsigned long flags, secs; + unsigned long secs; int err; err = rtc_tm_to_time(tm, &secs); if (err) return err; - spin_lock_irqsave(&p->lock, flags); - err = hypervisor_set_time(secs); - spin_unlock_irqrestore(&p->lock, flags); - - return err; + return hypervisor_set_time(secs); } static const struct rtc_class_ops sun4v_rtc_ops = { @@ -100,33 +77,22 @@ static const struct rtc_class_ops sun4v_rtc_ops = { .set_time = sun4v_set_time, }; -static int __devinit sun4v_rtc_probe(struct platform_device *pdev) +static int __init sun4v_rtc_probe(struct platform_device *pdev) { - struct sun4v_rtc *p = kzalloc(sizeof(*p), GFP_KERNEL); - - if (!p) - return -ENOMEM; - - spin_lock_init(&p->lock); - - p->rtc = rtc_device_register("sun4v", &pdev->dev, + struct rtc_device *rtc = rtc_device_register("sun4v", &pdev->dev, &sun4v_rtc_ops, THIS_MODULE); - if (IS_ERR(p->rtc)) { - int err = PTR_ERR(p->rtc); - kfree(p); - return err; - } - platform_set_drvdata(pdev, p); + if (IS_ERR(rtc)) + return PTR_ERR(rtc); + + platform_set_drvdata(pdev, rtc); return 0; } -static int __devexit sun4v_rtc_remove(struct platform_device *pdev) +static int __exit sun4v_rtc_remove(struct platform_device *pdev) { - struct sun4v_rtc *p = platform_get_drvdata(pdev); - - rtc_device_unregister(p->rtc); - kfree(p); + struct rtc_device *rtc = platform_get_drvdata(pdev); + rtc_device_unregister(rtc); return 0; } @@ -135,13 +101,12 @@ static struct platform_driver sun4v_rtc_driver = { .name = "rtc-sun4v", .owner = THIS_MODULE, }, - .probe = sun4v_rtc_probe, - .remove = __devexit_p(sun4v_rtc_remove), + .remove = __exit_p(sun4v_rtc_remove), }; static int __init sun4v_rtc_init(void) { - return platform_driver_register(&sun4v_rtc_driver); + return platform_driver_probe(&sun4v_rtc_driver, sun4v_rtc_probe); } static void __exit sun4v_rtc_exit(void) @@ -151,3 +116,7 @@ static void __exit sun4v_rtc_exit(void) module_init(sun4v_rtc_init); module_exit(sun4v_rtc_exit); + +MODULE_AUTHOR("David S. Miller <davem@davemloft.net>"); +MODULE_DESCRIPTION("SUN4V RTC driver"); +MODULE_LICENSE("GPL"); diff --git a/drivers/s390/block/dasd.c b/drivers/s390/block/dasd.c index 4b76fca..363bd13 100644 --- a/drivers/s390/block/dasd.c +++ b/drivers/s390/block/dasd.c @@ -1746,6 +1746,11 @@ restart: goto restart; } + /* log sense for fatal error */ + if (cqr->status == DASD_CQR_FAILED) { + dasd_log_sense(cqr, &cqr->irb); + } + /* First of all call extended error reporting. */ if (dasd_eer_enabled(base) && cqr->status == DASD_CQR_FAILED) { diff --git a/drivers/s390/char/sclp_cmd.c b/drivers/s390/char/sclp_cmd.c index eb5f1b8..ec9c0bc 100644 --- a/drivers/s390/char/sclp_cmd.c +++ b/drivers/s390/char/sclp_cmd.c @@ -324,6 +324,9 @@ static int do_assign_storage(sclp_cmdw_t cmd, u16 rn) case 0x0120: break; default: + pr_warning("assign storage failed (cmd=0x%08x, " + "response=0x%04x, rn=0x%04x)\n", cmd, + sccb->header.response_code, rn); rc = -EIO; break; } diff --git a/drivers/s390/cio/device.c b/drivers/s390/cio/device.c index 4e78c82..4e40083 100644 --- a/drivers/s390/cio/device.c +++ b/drivers/s390/cio/device.c @@ -874,11 +874,15 @@ void ccw_device_move_to_orphanage(struct work_struct *work) replacing_cdev = get_disc_ccwdev_by_dev_id(&dev_id, cdev); if (replacing_cdev) { sch_attach_disconnected_device(sch, replacing_cdev); + /* Release reference from get_disc_ccwdev_by_dev_id() */ + put_device(&cdev->dev); return; } replacing_cdev = get_orphaned_ccwdev_by_dev_id(css, &dev_id); if (replacing_cdev) { sch_attach_orphaned_device(sch, replacing_cdev); + /* Release reference from get_orphaned_ccwdev_by_dev_id() */ + put_device(&cdev->dev); return; } sch_create_and_recog_new_device(sch); diff --git a/drivers/s390/kvm/kvm_virtio.c b/drivers/s390/kvm/kvm_virtio.c index ff4a693..3d44244 100644 --- a/drivers/s390/kvm/kvm_virtio.c +++ b/drivers/s390/kvm/kvm_virtio.c @@ -322,13 +322,13 @@ static int __init kvm_devices_init(void) return rc; } - rc = vmem_add_mapping(PFN_PHYS(max_pfn), PAGE_SIZE); + rc = vmem_add_mapping(real_memory_size, PAGE_SIZE); if (rc) { s390_root_dev_unregister(kvm_root); return rc; } - kvm_devices = (void *) PFN_PHYS(max_pfn); + kvm_devices = (void *) real_memory_size; ctl_set_bit(0, 9); register_external_interrupt(0x2603, kvm_extint_handler); diff --git a/drivers/s390/scsi/zfcp_aux.c b/drivers/s390/scsi/zfcp_aux.c index 3b56220..3d4e3e3 100644 --- a/drivers/s390/scsi/zfcp_aux.c +++ b/drivers/s390/scsi/zfcp_aux.c @@ -610,7 +610,8 @@ struct zfcp_port *zfcp_port_enqueue(struct zfcp_adapter *adapter, u64 wwpn, atomic_set_mask(status | ZFCP_STATUS_COMMON_REMOVE, &port->status); atomic_set(&port->refcount, 0); - dev_set_name(&port->sysfs_device, "0x%016llx", wwpn); + dev_set_name(&port->sysfs_device, "0x%016llx", + (unsigned long long)wwpn); port->sysfs_device.parent = &adapter->ccw_device->dev; port->sysfs_device.release = zfcp_sysfs_port_release; diff --git a/drivers/s390/scsi/zfcp_ccw.c b/drivers/s390/scsi/zfcp_ccw.c index b04038c..951a8d4 100644 --- a/drivers/s390/scsi/zfcp_ccw.c +++ b/drivers/s390/scsi/zfcp_ccw.c @@ -116,7 +116,9 @@ static int zfcp_ccw_set_online(struct ccw_device *ccw_device) zfcp_erp_adapter_reopen(adapter, ZFCP_STATUS_COMMON_ERP_FAILED, 85, NULL); zfcp_erp_wait(adapter); - goto out; + up(&zfcp_data.config_sema); + flush_work(&adapter->scan_work); + return 0; out_scsi_register: zfcp_erp_thread_kill(adapter); diff --git a/drivers/s390/scsi/zfcp_dbf.c b/drivers/s390/scsi/zfcp_dbf.c index 060f5f2..31012d5 100644 --- a/drivers/s390/scsi/zfcp_dbf.c +++ b/drivers/s390/scsi/zfcp_dbf.c @@ -30,7 +30,7 @@ static void zfcp_dbf_hexdump(debug_info_t *dbf, void *to, int to_len, dump->offset = offset; dump->size = min(from_len - offset, room); memcpy(dump->data, from + offset, dump->size); - debug_event(dbf, level, dump, dump->size); + debug_event(dbf, level, dump, dump->size + sizeof(*dump)); } } @@ -108,7 +108,7 @@ static int zfcp_dbf_view_header(debug_info_t *id, struct debug_view *view, t.tv_sec, t.tv_nsec); zfcp_dbf_out(&p, "cpu", "%02i", entry->id.fields.cpuid); } else { - zfcp_dbf_outd(&p, NULL, dump->data, dump->size, dump->offset, + zfcp_dbf_outd(&p, "", dump->data, dump->size, dump->offset, dump->total_size); if ((dump->offset + dump->size) == dump->total_size) p += sprintf(p, "\n"); @@ -366,6 +366,7 @@ static void zfcp_hba_dbf_view_response(char **p, break; zfcp_dbf_out(p, "scsi_cmnd", "0x%0Lx", r->u.fcp.cmnd); zfcp_dbf_out(p, "scsi_serial", "0x%016Lx", r->u.fcp.serial); + p += sprintf(*p, "\n"); break; case FSF_QTCB_OPEN_PORT_WITH_DID: @@ -465,7 +466,8 @@ static int zfcp_hba_dbf_view_format(debug_info_t *id, struct debug_view *view, else if (strncmp(r->tag, "berr", ZFCP_DBF_TAG_SIZE) == 0) zfcp_hba_dbf_view_berr(&p, &r->u.berr); - p += sprintf(p, "\n"); + if (strncmp(r->tag, "resp", ZFCP_DBF_TAG_SIZE) != 0) + p += sprintf(p, "\n"); return p - out_buf; } @@ -880,6 +882,7 @@ void zfcp_san_dbf_event_ct_request(struct zfcp_fsf_req *fsf_req) struct ct_hdr *hdr = sg_virt(ct->req); struct zfcp_san_dbf_record *r = &adapter->san_dbf_buf; struct zfcp_san_dbf_record_ct_request *oct = &r->u.ct_req; + int level = 3; unsigned long flags; spin_lock_irqsave(&adapter->san_dbf_lock, flags); @@ -896,9 +899,10 @@ void zfcp_san_dbf_event_ct_request(struct zfcp_fsf_req *fsf_req) oct->options = hdr->options; oct->max_res_size = hdr->max_res_size; oct->len = min((int)ct->req->length - (int)sizeof(struct ct_hdr), - ZFCP_DBF_CT_PAYLOAD); - memcpy(oct->payload, (void *)hdr + sizeof(struct ct_hdr), oct->len); - debug_event(adapter->san_dbf, 3, r, sizeof(*r)); + ZFCP_DBF_SAN_MAX_PAYLOAD); + debug_event(adapter->san_dbf, level, r, sizeof(*r)); + zfcp_dbf_hexdump(adapter->san_dbf, r, sizeof(*r), level, + (void *)hdr + sizeof(struct ct_hdr), oct->len); spin_unlock_irqrestore(&adapter->san_dbf_lock, flags); } @@ -914,6 +918,7 @@ void zfcp_san_dbf_event_ct_response(struct zfcp_fsf_req *fsf_req) struct ct_hdr *hdr = sg_virt(ct->resp); struct zfcp_san_dbf_record *r = &adapter->san_dbf_buf; struct zfcp_san_dbf_record_ct_response *rct = &r->u.ct_resp; + int level = 3; unsigned long flags; spin_lock_irqsave(&adapter->san_dbf_lock, flags); @@ -929,9 +934,10 @@ void zfcp_san_dbf_event_ct_response(struct zfcp_fsf_req *fsf_req) rct->expl = hdr->reason_code_expl; rct->vendor_unique = hdr->vendor_unique; rct->len = min((int)ct->resp->length - (int)sizeof(struct ct_hdr), - ZFCP_DBF_CT_PAYLOAD); - memcpy(rct->payload, (void *)hdr + sizeof(struct ct_hdr), rct->len); - debug_event(adapter->san_dbf, 3, r, sizeof(*r)); + ZFCP_DBF_SAN_MAX_PAYLOAD); + debug_event(adapter->san_dbf, level, r, sizeof(*r)); + zfcp_dbf_hexdump(adapter->san_dbf, r, sizeof(*r), level, + (void *)hdr + sizeof(struct ct_hdr), rct->len); spin_unlock_irqrestore(&adapter->san_dbf_lock, flags); } @@ -954,7 +960,7 @@ static void zfcp_san_dbf_event_els(const char *tag, int level, rec->u.els.ls_code = ls_code; debug_event(adapter->san_dbf, level, rec, sizeof(*rec)); zfcp_dbf_hexdump(adapter->san_dbf, rec, sizeof(*rec), level, - buffer, min(buflen, ZFCP_DBF_ELS_MAX_PAYLOAD)); + buffer, min(buflen, ZFCP_DBF_SAN_MAX_PAYLOAD)); spin_unlock_irqrestore(&adapter->san_dbf_lock, flags); } @@ -1008,8 +1014,6 @@ static int zfcp_san_dbf_view_format(debug_info_t *id, struct debug_view *view, char *out_buf, const char *in_buf) { struct zfcp_san_dbf_record *r = (struct zfcp_san_dbf_record *)in_buf; - char *buffer = NULL; - int buflen = 0, total = 0; char *p = out_buf; if (strncmp(r->tag, "dump", ZFCP_DBF_TAG_SIZE) == 0) @@ -1029,9 +1033,6 @@ static int zfcp_san_dbf_view_format(debug_info_t *id, struct debug_view *view, zfcp_dbf_out(&p, "gs_subtype", "0x%02x", ct->gs_subtype); zfcp_dbf_out(&p, "options", "0x%02x", ct->options); zfcp_dbf_out(&p, "max_res_size", "0x%04x", ct->max_res_size); - total = ct->len; - buffer = ct->payload; - buflen = min(total, ZFCP_DBF_CT_PAYLOAD); } else if (strncmp(r->tag, "rctc", ZFCP_DBF_TAG_SIZE) == 0) { struct zfcp_san_dbf_record_ct_response *ct = &r->u.ct_resp; zfcp_dbf_out(&p, "cmd_rsp_code", "0x%04x", ct->cmd_rsp_code); @@ -1039,23 +1040,12 @@ static int zfcp_san_dbf_view_format(debug_info_t *id, struct debug_view *view, zfcp_dbf_out(&p, "reason_code", "0x%02x", ct->reason_code); zfcp_dbf_out(&p, "reason_code_expl", "0x%02x", ct->expl); zfcp_dbf_out(&p, "vendor_unique", "0x%02x", ct->vendor_unique); - total = ct->len; - buffer = ct->payload; - buflen = min(total, ZFCP_DBF_CT_PAYLOAD); } else if (strncmp(r->tag, "oels", ZFCP_DBF_TAG_SIZE) == 0 || strncmp(r->tag, "rels", ZFCP_DBF_TAG_SIZE) == 0 || strncmp(r->tag, "iels", ZFCP_DBF_TAG_SIZE) == 0) { struct zfcp_san_dbf_record_els *els = &r->u.els; zfcp_dbf_out(&p, "ls_code", "0x%02x", els->ls_code); - total = els->len; - buffer = els->payload; - buflen = min(total, ZFCP_DBF_ELS_PAYLOAD); } - - zfcp_dbf_outd(&p, "payload", buffer, buflen, 0, total); - if (buflen == total) - p += sprintf(p, "\n"); - return p - out_buf; } diff --git a/drivers/s390/scsi/zfcp_dbf.h b/drivers/s390/scsi/zfcp_dbf.h index e8f4508..5d6b2df 100644 --- a/drivers/s390/scsi/zfcp_dbf.h +++ b/drivers/s390/scsi/zfcp_dbf.h @@ -163,8 +163,6 @@ struct zfcp_san_dbf_record_ct_request { u8 options; u16 max_res_size; u32 len; -#define ZFCP_DBF_CT_PAYLOAD 24 - u8 payload[ZFCP_DBF_CT_PAYLOAD]; } __attribute__ ((packed)); struct zfcp_san_dbf_record_ct_response { @@ -174,15 +172,11 @@ struct zfcp_san_dbf_record_ct_response { u8 expl; u8 vendor_unique; u32 len; - u8 payload[ZFCP_DBF_CT_PAYLOAD]; } __attribute__ ((packed)); struct zfcp_san_dbf_record_els { u8 ls_code; u32 len; -#define ZFCP_DBF_ELS_PAYLOAD 32 -#define ZFCP_DBF_ELS_MAX_PAYLOAD 1024 - u8 payload[ZFCP_DBF_ELS_PAYLOAD]; } __attribute__ ((packed)); struct zfcp_san_dbf_record { @@ -196,6 +190,8 @@ struct zfcp_san_dbf_record { struct zfcp_san_dbf_record_ct_response ct_resp; struct zfcp_san_dbf_record_els els; } u; +#define ZFCP_DBF_SAN_MAX_PAYLOAD 1024 + u8 payload[32]; } __attribute__ ((packed)); struct zfcp_scsi_dbf_record { diff --git a/drivers/s390/scsi/zfcp_erp.c b/drivers/s390/scsi/zfcp_erp.c index 9040f73..35364f6 100644 --- a/drivers/s390/scsi/zfcp_erp.c +++ b/drivers/s390/scsi/zfcp_erp.c @@ -472,6 +472,7 @@ static void zfcp_erp_strategy_check_fsfreq(struct zfcp_erp_action *act) ZFCP_STATUS_ERP_TIMEDOUT)) { act->fsf_req->status |= ZFCP_STATUS_FSFREQ_DISMISSED; zfcp_rec_dbf_event_action(142, act); + act->fsf_req->erp_action = NULL; } if (act->status & ZFCP_STATUS_ERP_TIMEDOUT) zfcp_rec_dbf_event_action(143, act); diff --git a/drivers/s390/scsi/zfcp_fsf.c b/drivers/s390/scsi/zfcp_fsf.c index 5ae1d49..d024442 100644 --- a/drivers/s390/scsi/zfcp_fsf.c +++ b/drivers/s390/scsi/zfcp_fsf.c @@ -683,6 +683,7 @@ static struct zfcp_fsf_req *zfcp_fsf_alloc_noqtcb(mempool_t *pool) if (!req) return NULL; memset(req, 0, sizeof(*req)); + req->pool = pool; return req; } @@ -769,28 +770,24 @@ static struct zfcp_fsf_req *zfcp_fsf_req_create(struct zfcp_adapter *adapter, static int zfcp_fsf_req_send(struct zfcp_fsf_req *req) { struct zfcp_adapter *adapter = req->adapter; - struct zfcp_qdio_queue *req_q = &adapter->req_q; + unsigned long flags; int idx; /* put allocated FSF request into hash table */ - spin_lock(&adapter->req_list_lock); + spin_lock_irqsave(&adapter->req_list_lock, flags); idx = zfcp_reqlist_hash(req->req_id); list_add_tail(&req->list, &adapter->req_list[idx]); - spin_unlock(&adapter->req_list_lock); + spin_unlock_irqrestore(&adapter->req_list_lock, flags); - req->qdio_outb_usage = atomic_read(&req_q->count); + req->qdio_outb_usage = atomic_read(&adapter->req_q.count); req->issued = get_clock(); if (zfcp_qdio_send(req)) { - /* Queues are down..... */ del_timer(&req->timer); - spin_lock(&adapter->req_list_lock); - zfcp_reqlist_remove(adapter, req); - spin_unlock(&adapter->req_list_lock); - /* undo changes in request queue made for this request */ - atomic_add(req->sbal_number, &req_q->count); - req_q->first -= req->sbal_number; - req_q->first += QDIO_MAX_BUFFERS_PER_Q; - req_q->first %= QDIO_MAX_BUFFERS_PER_Q; /* wrap */ + spin_lock_irqsave(&adapter->req_list_lock, flags); + /* lookup request again, list might have changed */ + if (zfcp_reqlist_find_safe(adapter, req)) + zfcp_reqlist_remove(adapter, req); + spin_unlock_irqrestore(&adapter->req_list_lock, flags); zfcp_erp_adapter_reopen(adapter, 0, 116, req); return -EIO; } diff --git a/drivers/s390/scsi/zfcp_scsi.c b/drivers/s390/scsi/zfcp_scsi.c index ca8f85f..e46fd3e 100644 --- a/drivers/s390/scsi/zfcp_scsi.c +++ b/drivers/s390/scsi/zfcp_scsi.c @@ -24,14 +24,10 @@ char *zfcp_get_fcp_sns_info_ptr(struct fcp_rsp_iu *fcp_rsp_iu) static void zfcp_scsi_slave_destroy(struct scsi_device *sdpnt) { struct zfcp_unit *unit = (struct zfcp_unit *) sdpnt->hostdata; - WARN_ON(!unit); - if (unit) { - atomic_clear_mask(ZFCP_STATUS_UNIT_REGISTERED, &unit->status); - sdpnt->hostdata = NULL; - unit->device = NULL; - zfcp_erp_unit_failed(unit, 12, NULL); - zfcp_unit_put(unit); - } + atomic_clear_mask(ZFCP_STATUS_UNIT_REGISTERED, &unit->status); + unit->device = NULL; + zfcp_erp_unit_failed(unit, 12, NULL); + zfcp_unit_put(unit); } static int zfcp_scsi_slave_configure(struct scsi_device *sdp) diff --git a/drivers/scsi/dpt_i2o.c b/drivers/scsi/dpt_i2o.c index 8aba4fd..6194ed5 100644 --- a/drivers/scsi/dpt_i2o.c +++ b/drivers/scsi/dpt_i2o.c @@ -2445,7 +2445,7 @@ static s32 adpt_i2o_to_scsi(void __iomem *reply, struct scsi_cmnd* cmd) hba_status = detailed_status >> 8; // calculate resid for sg - scsi_set_resid(cmd, scsi_bufflen(cmd) - readl(reply+5)); + scsi_set_resid(cmd, scsi_bufflen(cmd) - readl(reply+20)); pHba = (adpt_hba*) cmd->device->host->hostdata[0]; @@ -2456,7 +2456,7 @@ static s32 adpt_i2o_to_scsi(void __iomem *reply, struct scsi_cmnd* cmd) case I2O_SCSI_DSC_SUCCESS: cmd->result = (DID_OK << 16); // handle underflow - if(readl(reply+5) < cmd->underflow ) { + if (readl(reply+20) < cmd->underflow) { cmd->result = (DID_ERROR <<16); printk(KERN_WARNING"%s: SCSI CMD underflow\n",pHba->name); } diff --git a/drivers/scsi/megaraid.c b/drivers/scsi/megaraid.c index 28c9da7..7dc62de 100644 --- a/drivers/scsi/megaraid.c +++ b/drivers/scsi/megaraid.c @@ -4402,6 +4402,10 @@ mega_internal_command(adapter_t *adapter, megacmd_t *mc, mega_passthru *pthru) scb_t *scb; int rval; + scmd = scsi_allocate_command(GFP_KERNEL); + if (!scmd) + return -ENOMEM; + /* * The internal commands share one command id and hence are * serialized. This is so because we want to reserve maximum number of @@ -4412,12 +4416,11 @@ mega_internal_command(adapter_t *adapter, megacmd_t *mc, mega_passthru *pthru) scb = &adapter->int_scb; memset(scb, 0, sizeof(scb_t)); - scmd = &adapter->int_scmd; - memset(scmd, 0, sizeof(Scsi_Cmnd)); - sdev = kzalloc(sizeof(struct scsi_device), GFP_KERNEL); scmd->device = sdev; + memset(adapter->int_cdb, 0, sizeof(adapter->int_cdb)); + scmd->cmnd = adapter->int_cdb; scmd->device->host = adapter->host; scmd->host_scribble = (void *)scb; scmd->cmnd[0] = MEGA_INTERNAL_CMD; @@ -4456,6 +4459,8 @@ mega_internal_command(adapter_t *adapter, megacmd_t *mc, mega_passthru *pthru) mutex_unlock(&adapter->int_mtx); + scsi_free_command(GFP_KERNEL, scmd); + return rval; } diff --git a/drivers/scsi/megaraid.h b/drivers/scsi/megaraid.h index ee70bd4..795201f 100644 --- a/drivers/scsi/megaraid.h +++ b/drivers/scsi/megaraid.h @@ -888,8 +888,8 @@ typedef struct { u8 sglen; /* f/w supported scatter-gather list length */ + unsigned char int_cdb[MAX_COMMAND_SIZE]; scb_t int_scb; - Scsi_Cmnd int_scmd; struct mutex int_mtx; /* To synchronize the internal commands */ struct completion int_waitq; /* wait queue for internal diff --git a/drivers/scsi/qla2xxx/qla_def.h b/drivers/scsi/qla2xxx/qla_def.h index f25f41a..b971940 100644 --- a/drivers/scsi/qla2xxx/qla_def.h +++ b/drivers/scsi/qla2xxx/qla_def.h @@ -2547,7 +2547,6 @@ typedef struct scsi_qla_host { uint8_t fcode_revision[16]; uint32_t fw_revision[4]; - uint16_t fdt_odd_index; uint32_t fdt_wrt_disable; uint32_t fdt_erase_cmd; uint32_t fdt_block_size; diff --git a/drivers/scsi/qla2xxx/qla_init.c b/drivers/scsi/qla2xxx/qla_init.c index a470f2d..4218f20 100644 --- a/drivers/scsi/qla2xxx/qla_init.c +++ b/drivers/scsi/qla2xxx/qla_init.c @@ -140,7 +140,6 @@ int qla2100_pci_config(scsi_qla_host_t *ha) { uint16_t w; - uint32_t d; unsigned long flags; struct device_reg_2xxx __iomem *reg = &ha->iobase->isp; @@ -151,10 +150,7 @@ qla2100_pci_config(scsi_qla_host_t *ha) w |= (PCI_COMMAND_PARITY | PCI_COMMAND_SERR); pci_write_config_word(ha->pdev, PCI_COMMAND, w); - /* Reset expansion ROM address decode enable */ - pci_read_config_dword(ha->pdev, PCI_ROM_ADDRESS, &d); - d &= ~PCI_ROM_ADDRESS_ENABLE; - pci_write_config_dword(ha->pdev, PCI_ROM_ADDRESS, d); + pci_disable_rom(ha->pdev); /* Get PCI bus information. */ spin_lock_irqsave(&ha->hardware_lock, flags); @@ -174,7 +170,6 @@ int qla2300_pci_config(scsi_qla_host_t *ha) { uint16_t w; - uint32_t d; unsigned long flags = 0; uint32_t cnt; struct device_reg_2xxx __iomem *reg = &ha->iobase->isp; @@ -236,10 +231,7 @@ qla2300_pci_config(scsi_qla_host_t *ha) pci_write_config_byte(ha->pdev, PCI_LATENCY_TIMER, 0x80); - /* Reset expansion ROM address decode enable */ - pci_read_config_dword(ha->pdev, PCI_ROM_ADDRESS, &d); - d &= ~PCI_ROM_ADDRESS_ENABLE; - pci_write_config_dword(ha->pdev, PCI_ROM_ADDRESS, d); + pci_disable_rom(ha->pdev); /* Get PCI bus information. */ spin_lock_irqsave(&ha->hardware_lock, flags); @@ -259,7 +251,6 @@ int qla24xx_pci_config(scsi_qla_host_t *ha) { uint16_t w; - uint32_t d; unsigned long flags = 0; struct device_reg_24xx __iomem *reg = &ha->iobase->isp24; @@ -281,10 +272,7 @@ qla24xx_pci_config(scsi_qla_host_t *ha) if (pci_find_capability(ha->pdev, PCI_CAP_ID_EXP)) pcie_set_readrq(ha->pdev, 2048); - /* Reset expansion ROM address decode enable */ - pci_read_config_dword(ha->pdev, PCI_ROM_ADDRESS, &d); - d &= ~PCI_ROM_ADDRESS_ENABLE; - pci_write_config_dword(ha->pdev, PCI_ROM_ADDRESS, d); + pci_disable_rom(ha->pdev); ha->chip_revision = ha->pdev->revision; @@ -306,7 +294,6 @@ int qla25xx_pci_config(scsi_qla_host_t *ha) { uint16_t w; - uint32_t d; pci_set_master(ha->pdev); pci_try_set_mwi(ha->pdev); @@ -320,10 +307,7 @@ qla25xx_pci_config(scsi_qla_host_t *ha) if (pci_find_capability(ha->pdev, PCI_CAP_ID_EXP)) pcie_set_readrq(ha->pdev, 2048); - /* Reset expansion ROM address decode enable */ - pci_read_config_dword(ha->pdev, PCI_ROM_ADDRESS, &d); - d &= ~PCI_ROM_ADDRESS_ENABLE; - pci_write_config_dword(ha->pdev, PCI_ROM_ADDRESS, d); + pci_disable_rom(ha->pdev); ha->chip_revision = ha->pdev->revision; @@ -980,7 +964,6 @@ qla2x00_setup_chip(scsi_qla_host_t *ha) &ha->fw_minor_version, &ha->fw_subminor_version, &ha->fw_attributes, &ha->fw_memory_size); - qla2x00_resize_request_q(ha); ha->flags.npiv_supported = 0; if ((IS_QLA24XX(ha) || IS_QLA25XX(ha) || IS_QLA84XX(ha)) && @@ -992,6 +975,7 @@ qla2x00_setup_chip(scsi_qla_host_t *ha) ha->max_npiv_vports = MIN_MULTI_ID_FABRIC - 1; } + qla2x00_resize_request_q(ha); if (ql2xallocfwdump) qla2x00_alloc_fw_dump(ha); diff --git a/drivers/scsi/qla2xxx/qla_mbx.c b/drivers/scsi/qla2xxx/qla_mbx.c index 36bc685..3402746 100644 --- a/drivers/scsi/qla2xxx/qla_mbx.c +++ b/drivers/scsi/qla2xxx/qla_mbx.c @@ -1964,7 +1964,7 @@ qla2x00_get_resource_cnts(scsi_qla_host_t *ha, uint16_t *cur_xchg_cnt, *cur_iocb_cnt = mcp->mb[7]; if (orig_iocb_cnt) *orig_iocb_cnt = mcp->mb[10]; - if (max_npiv_vports) + if (ha->flags.npiv_supported && max_npiv_vports) *max_npiv_vports = mcp->mb[11]; } diff --git a/drivers/scsi/qla2xxx/qla_os.c b/drivers/scsi/qla2xxx/qla_os.c index 21dd182..3556720 100644 --- a/drivers/scsi/qla2xxx/qla_os.c +++ b/drivers/scsi/qla2xxx/qla_os.c @@ -728,6 +728,7 @@ qla2xxx_eh_abort(struct scsi_cmnd *cmd) if (ha->isp_ops->abort_command(ha, sp)) { DEBUG2(printk("%s(%ld): abort_command " "mbx failed.\n", __func__, ha->host_no)); + ret = FAILED; } else { DEBUG3(printk("%s(%ld): abort_command " "mbx success.\n", __func__, ha->host_no)); diff --git a/drivers/scsi/qla2xxx/qla_sup.c b/drivers/scsi/qla2xxx/qla_sup.c index 90a1321..e4af678 100644 --- a/drivers/scsi/qla2xxx/qla_sup.c +++ b/drivers/scsi/qla2xxx/qla_sup.c @@ -722,6 +722,7 @@ done: static void qla2xxx_get_fdt_info(scsi_qla_host_t *ha) { +#define FLASH_BLK_SIZE_4K 0x1000 #define FLASH_BLK_SIZE_32K 0x8000 #define FLASH_BLK_SIZE_64K 0x10000 const char *loc, *locations[] = { "MID", "FDT" }; @@ -755,7 +756,6 @@ qla2xxx_get_fdt_info(scsi_qla_host_t *ha) loc = locations[1]; mid = le16_to_cpu(fdt->man_id); fid = le16_to_cpu(fdt->id); - ha->fdt_odd_index = mid == 0x1f; ha->fdt_wrt_disable = fdt->wrt_disable_bits; ha->fdt_erase_cmd = flash_conf_to_access_addr(0x0300 | fdt->erase_cmd); ha->fdt_block_size = le32_to_cpu(fdt->block_size); @@ -788,8 +788,7 @@ no_flash_data: ha->fdt_block_size = FLASH_BLK_SIZE_64K; break; case 0x1f: /* Atmel 26DF081A. */ - ha->fdt_odd_index = 1; - ha->fdt_block_size = FLASH_BLK_SIZE_64K; + ha->fdt_block_size = FLASH_BLK_SIZE_4K; ha->fdt_erase_cmd = flash_conf_to_access_addr(0x0320); ha->fdt_unprotect_sec_cmd = flash_conf_to_access_addr(0x0339); ha->fdt_protect_sec_cmd = flash_conf_to_access_addr(0x0336); @@ -801,9 +800,9 @@ no_flash_data: } done: DEBUG2(qla_printk(KERN_DEBUG, ha, "FDT[%s]: (0x%x/0x%x) erase=0x%x " - "pro=%x upro=%x idx=%d wrtd=0x%x blk=0x%x.\n", loc, mid, fid, + "pro=%x upro=%x wrtd=0x%x blk=0x%x.\n", loc, mid, fid, ha->fdt_erase_cmd, ha->fdt_protect_sec_cmd, - ha->fdt_unprotect_sec_cmd, ha->fdt_odd_index, ha->fdt_wrt_disable, + ha->fdt_unprotect_sec_cmd, ha->fdt_wrt_disable, ha->fdt_block_size)); } @@ -987,13 +986,9 @@ qla24xx_write_flash_data(scsi_qla_host_t *ha, uint32_t *dwptr, uint32_t faddr, qla24xx_unprotect_flash(ha); for (liter = 0; liter < dwords; liter++, faddr++, dwptr++) { - if (ha->fdt_odd_index) { - findex = faddr << 2; - fdata = findex & sec_mask; - } else { - findex = faddr; - fdata = (findex & sec_mask) << 2; - } + + findex = faddr; + fdata = (findex & sec_mask) << 2; /* Are we at the beginning of a sector? */ if ((findex & rest_addr) == 0) { diff --git a/drivers/scsi/qla2xxx/qla_version.h b/drivers/scsi/qla2xxx/qla_version.h index be5e299..eea6720 100644 --- a/drivers/scsi/qla2xxx/qla_version.h +++ b/drivers/scsi/qla2xxx/qla_version.h @@ -7,7 +7,7 @@ /* * Driver version */ -#define QLA2XXX_VERSION "8.02.01-k8" +#define QLA2XXX_VERSION "8.02.01-k9" #define QLA_DRIVER_MAJOR_VER 8 #define QLA_DRIVER_MINOR_VER 2 diff --git a/drivers/scsi/scsi_error.c b/drivers/scsi/scsi_error.c index 94ed262..3863617 100644 --- a/drivers/scsi/scsi_error.c +++ b/drivers/scsi/scsi_error.c @@ -1340,9 +1340,10 @@ int scsi_decide_disposition(struct scsi_cmnd *scmd) * LLD/transport was disrupted during processing of the IO. * The transport class is now blocked/blocking, * and the transport will decide what to do with the IO - * based on its timers and recovery capablilities. + * based on its timers and recovery capablilities if + * there are enough retries. */ - return ADD_TO_MLQUEUE; + goto maybe_retry; case DID_TRANSPORT_FAILFAST: /* * The transport decided to failfast the IO (most likely diff --git a/drivers/serial/sh-sci.c b/drivers/serial/sh-sci.c index 5c0f32c7..165fc01 100644 --- a/drivers/serial/sh-sci.c +++ b/drivers/serial/sh-sci.c @@ -144,9 +144,9 @@ static void put_char(struct uart_port *port, char c) status = sci_in(port, SCxSR); } while (!(status & SCxSR_TDxE(port))); - sci_out(port, SCxTDR, c); sci_in(port, SCxSR); /* Dummy read */ sci_out(port, SCxSR, SCxSR_TDxE_CLEAR(port)); + sci_out(port, SCxTDR, c); spin_unlock_irqrestore(&port->lock, flags); } @@ -478,10 +478,10 @@ static void sci_transmit_chars(struct uart_port *port) return; } - if (port->type == PORT_SCIF) - count = scif_txroom(port); - else + if (port->type == PORT_SCI) count = sci_txroom(port); + else + count = scif_txroom(port); do { unsigned char c; @@ -510,7 +510,7 @@ static void sci_transmit_chars(struct uart_port *port) } else { ctrl = sci_in(port, SCSCR); - if (port->type == PORT_SCIF) { + if (port->type != PORT_SCI) { sci_in(port, SCxSR); /* Dummy read */ sci_out(port, SCxSR, SCxSR_TDxE_CLEAR(port)); } @@ -536,10 +536,10 @@ static inline void sci_receive_chars(struct uart_port *port) return; while (1) { - if (port->type == PORT_SCIF) - count = scif_rxroom(port); - else + if (port->type == PORT_SCI) count = sci_rxroom(port); + else + count = scif_rxroom(port); /* Don't copy more bytes than there is room for in the buffer */ count = tty_buffer_request_room(tty, count); @@ -714,7 +714,7 @@ static inline int sci_handle_breaks(struct uart_port *port) #if defined(SCIF_ORER) /* XXX: Handle SCIF overrun error */ - if (port->type == PORT_SCIF && (sci_in(port, SCLSR) & SCIF_ORER) != 0) { + if (port->type != PORT_SCI && (sci_in(port, SCLSR) & SCIF_ORER) != 0) { sci_out(port, SCLSR, 0); if (tty_insert_flip_char(tty, 0, TTY_OVERRUN)) { copied++; @@ -1042,7 +1042,7 @@ static void sci_set_termios(struct uart_port *port, struct ktermios *termios, sci_out(port, SCSCR, 0x00); /* TE=0, RE=0, CKE1=0 */ - if (port->type == PORT_SCIF) + if (port->type != PORT_SCI) sci_out(port, SCFCR, SCFCR_RFRST | SCFCR_TFRST); smr_val = sci_in(port, SCSMR) & 3; @@ -1085,6 +1085,7 @@ static const char *sci_type(struct uart_port *port) case PORT_SCI: return "sci"; case PORT_SCIF: return "scif"; case PORT_IRDA: return "irda"; + case PORT_SCIFA: return "scifa"; } return NULL; @@ -1112,6 +1113,7 @@ static void sci_config_port(struct uart_port *port, int flags) s->init_pins = sci_init_pins_sci; break; case PORT_SCIF: + case PORT_SCIFA: s->init_pins = sci_init_pins_scif; break; case PORT_IRDA: diff --git a/drivers/serial/sh-sci.h b/drivers/serial/sh-sci.h index 6163a45..9f33b06 100644 --- a/drivers/serial/sh-sci.h +++ b/drivers/serial/sh-sci.h @@ -289,18 +289,18 @@ #define CPU_SCIx_FNS(name, sci_offset, sci_size, scif_offset, scif_size)\ static inline unsigned int sci_##name##_in(struct uart_port *port) \ { \ - if (port->type == PORT_SCI) { \ - SCI_IN(sci_size, sci_offset) \ - } else { \ - SCI_IN(scif_size, scif_offset); \ + if (port->type == PORT_SCIF) { \ + SCI_IN(scif_size, scif_offset) \ + } else { /* PORT_SCI or PORT_SCIFA */ \ + SCI_IN(sci_size, sci_offset); \ } \ } \ static inline void sci_##name##_out(struct uart_port *port, unsigned int value) \ { \ - if (port->type == PORT_SCI) { \ - SCI_OUT(sci_size, sci_offset, value) \ - } else { \ - SCI_OUT(scif_size, scif_offset, value); \ + if (port->type == PORT_SCIF) { \ + SCI_OUT(scif_size, scif_offset, value) \ + } else { /* PORT_SCI or PORT_SCIFA */ \ + SCI_OUT(sci_size, sci_offset, value); \ } \ } diff --git a/drivers/usb/class/cdc-acm.c b/drivers/usb/class/cdc-acm.c index 2010444..d50a99f 100644 --- a/drivers/usb/class/cdc-acm.c +++ b/drivers/usb/class/cdc-acm.c @@ -158,16 +158,12 @@ static int acm_wb_is_avail(struct acm *acm) } /* - * Finish write. + * Finish write. Caller must hold acm->write_lock */ static void acm_write_done(struct acm *acm, struct acm_wb *wb) { - unsigned long flags; - - spin_lock_irqsave(&acm->write_lock, flags); wb->use = 0; acm->transmitting--; - spin_unlock_irqrestore(&acm->write_lock, flags); } /* @@ -482,6 +478,7 @@ static void acm_write_bulk(struct urb *urb) { struct acm_wb *wb = urb->context; struct acm *acm = wb->instance; + unsigned long flags; if (verbose || urb->status || (urb->actual_length != urb->transfer_buffer_length)) @@ -490,7 +487,9 @@ static void acm_write_bulk(struct urb *urb) urb->transfer_buffer_length, urb->status); + spin_lock_irqsave(&acm->write_lock, flags); acm_write_done(acm, wb); + spin_unlock_irqrestore(&acm->write_lock, flags); if (ACM_READY(acm)) schedule_work(&acm->work); else diff --git a/drivers/usb/core/message.c b/drivers/usb/core/message.c index 8877385..6d1048f 100644 --- a/drivers/usb/core/message.c +++ b/drivers/usb/core/message.c @@ -1091,6 +1091,7 @@ void usb_disable_device(struct usb_device *dev, int skip_ep0) continue; dev_dbg(&dev->dev, "unregistering interface %s\n", dev_name(&interface->dev)); + interface->unregistering = 1; usb_remove_sysfs_intf_files(interface); device_del(&interface->dev); } diff --git a/drivers/usb/core/sysfs.c b/drivers/usb/core/sysfs.c index f66fba1..4fb65fd 100644 --- a/drivers/usb/core/sysfs.c +++ b/drivers/usb/core/sysfs.c @@ -840,7 +840,7 @@ int usb_create_sysfs_intf_files(struct usb_interface *intf) struct usb_host_interface *alt = intf->cur_altsetting; int retval; - if (intf->sysfs_files_created) + if (intf->sysfs_files_created || intf->unregistering) return 0; /* The interface string may be present in some altsettings diff --git a/drivers/usb/core/urb.c b/drivers/usb/core/urb.c index 4342bd9..1f68af9 100644 --- a/drivers/usb/core/urb.c +++ b/drivers/usb/core/urb.c @@ -85,8 +85,8 @@ EXPORT_SYMBOL_GPL(usb_alloc_urb); * Must be called when a user of a urb is finished with it. When the last user * of the urb calls this function, the memory of the urb is freed. * - * Note: The transfer buffer associated with the urb is not freed, that must be - * done elsewhere. + * Note: The transfer buffer associated with the urb is not freed unless the + * URB_FREE_BUFFER transfer flag is set. */ void usb_free_urb(struct urb *urb) { diff --git a/drivers/usb/gadget/f_acm.c b/drivers/usb/gadget/f_acm.c index 5ee1590..c1d34df 100644 --- a/drivers/usb/gadget/f_acm.c +++ b/drivers/usb/gadget/f_acm.c @@ -463,7 +463,11 @@ static int acm_cdc_notify(struct f_acm *acm, u8 type, u16 value, notify->wLength = cpu_to_le16(length); memcpy(buf, data, length); + /* ep_queue() can complete immediately if it fills the fifo... */ + spin_unlock(&acm->lock); status = usb_ep_queue(ep, req, GFP_ATOMIC); + spin_lock(&acm->lock); + if (status < 0) { ERROR(acm->port.func.config->cdev, "acm ttyGS%d can't notify serial state, %d\n", diff --git a/drivers/usb/host/Kconfig b/drivers/usb/host/Kconfig index 56f592d..f3a75a9 100644 --- a/drivers/usb/host/Kconfig +++ b/drivers/usb/host/Kconfig @@ -110,29 +110,18 @@ config USB_ISP116X_HCD config USB_ISP1760_HCD tristate "ISP 1760 HCD support" - depends on USB && EXPERIMENTAL + depends on USB && EXPERIMENTAL && (PCI || PPC_OF) ---help--- The ISP1760 chip is a USB 2.0 host controller. This driver does not support isochronous transfers or OTG. + This USB controller is usually attached to a non-DMA-Master + capable bus. NXP's eval kit brings this chip on PCI card + where the chip itself is behind a PLB to simulate such + a bus. To compile this driver as a module, choose M here: the - module will be called isp1760-hcd. - -config USB_ISP1760_PCI - bool "Support for the PCI bus" - depends on USB_ISP1760_HCD && PCI - ---help--- - Enables support for the device present on the PCI bus. - This should only be required if you happen to have the eval kit from - NXP and you are going to test it. - -config USB_ISP1760_OF - bool "Support for the OF platform bus" - depends on USB_ISP1760_HCD && PPC_OF - ---help--- - Enables support for the device present on the PowerPC - OpenFirmware platform bus. + module will be called isp1760. config USB_OHCI_HCD tristate "OHCI HCD support" diff --git a/drivers/usb/host/ehci-hcd.c b/drivers/usb/host/ehci-hcd.c index 15a803b..4725d15 100644 --- a/drivers/usb/host/ehci-hcd.c +++ b/drivers/usb/host/ehci-hcd.c @@ -643,7 +643,7 @@ static int ehci_run (struct usb_hcd *hcd) static irqreturn_t ehci_irq (struct usb_hcd *hcd) { struct ehci_hcd *ehci = hcd_to_ehci (hcd); - u32 status, pcd_status = 0, cmd; + u32 status, masked_status, pcd_status = 0, cmd; int bh; spin_lock (&ehci->lock); @@ -656,14 +656,14 @@ static irqreturn_t ehci_irq (struct usb_hcd *hcd) goto dead; } - status &= INTR_MASK; - if (!status) { /* irq sharing? */ + masked_status = status & INTR_MASK; + if (!masked_status) { /* irq sharing? */ spin_unlock(&ehci->lock); return IRQ_NONE; } /* clear (just) interrupts */ - ehci_writel(ehci, status, &ehci->regs->status); + ehci_writel(ehci, masked_status, &ehci->regs->status); cmd = ehci_readl(ehci, &ehci->regs->command); bh = 0; @@ -734,18 +734,17 @@ static irqreturn_t ehci_irq (struct usb_hcd *hcd) /* PCI errors [4.15.2.4] */ if (unlikely ((status & STS_FATAL) != 0)) { + ehci_err(ehci, "fatal error\n"); dbg_cmd(ehci, "fatal", cmd); dbg_status(ehci, "fatal", status); - if (status & STS_HALT) { - ehci_err (ehci, "fatal error\n"); + ehci_halt(ehci); dead: - ehci_reset (ehci); - ehci_writel(ehci, 0, &ehci->regs->configured_flag); - /* generic layer kills/unlinks all urbs, then - * uses ehci_stop to clean up the rest - */ - bh = 1; - } + ehci_reset(ehci); + ehci_writel(ehci, 0, &ehci->regs->configured_flag); + /* generic layer kills/unlinks all urbs, then + * uses ehci_stop to clean up the rest + */ + bh = 1; } if (bh) diff --git a/drivers/usb/host/ehci-ps3.c b/drivers/usb/host/ehci-ps3.c index 0eba894..9c9da35 100644 --- a/drivers/usb/host/ehci-ps3.c +++ b/drivers/usb/host/ehci-ps3.c @@ -205,6 +205,7 @@ static int ps3_ehci_remove(struct ps3_system_bus_device *dev) tmp = hcd->irq; + ehci_shutdown(hcd); usb_remove_hcd(hcd); ps3_system_bus_set_driver_data(dev, NULL); diff --git a/drivers/usb/host/ehci-sched.c b/drivers/usb/host/ehci-sched.c index 4a0c5a7..a081ee6 100644 --- a/drivers/usb/host/ehci-sched.c +++ b/drivers/usb/host/ehci-sched.c @@ -918,7 +918,7 @@ iso_stream_init ( */ stream->usecs = HS_USECS_ISO (maxp); bandwidth = stream->usecs * 8; - bandwidth /= 1 << (interval - 1); + bandwidth /= interval; } else { u32 addr; @@ -951,7 +951,7 @@ iso_stream_init ( } else stream->raw_mask = smask_out [hs_transfers - 1]; bandwidth = stream->usecs + stream->c_usecs; - bandwidth /= 1 << (interval + 2); + bandwidth /= interval << 3; /* stream->splits gets created from raw_mask later */ stream->address = cpu_to_hc32(ehci, addr); diff --git a/drivers/usb/host/isp1760-if.c b/drivers/usb/host/isp1760-if.c index af849f5..b87ca7c 100644 --- a/drivers/usb/host/isp1760-if.c +++ b/drivers/usb/host/isp1760-if.c @@ -14,16 +14,16 @@ #include "../core/hcd.h" #include "isp1760-hcd.h" -#ifdef CONFIG_USB_ISP1760_OF +#ifdef CONFIG_PPC_OF #include <linux/of.h> #include <linux/of_platform.h> #endif -#ifdef CONFIG_USB_ISP1760_PCI +#ifdef CONFIG_PCI #include <linux/pci.h> #endif -#ifdef CONFIG_USB_ISP1760_OF +#ifdef CONFIG_PPC_OF static int of_isp1760_probe(struct of_device *dev, const struct of_device_id *match) { @@ -128,7 +128,7 @@ static struct of_platform_driver isp1760_of_driver = { }; #endif -#ifdef CONFIG_USB_ISP1760_PCI +#ifdef CONFIG_PCI static u32 nxp_pci_io_base; static u32 iolength; static u32 pci_mem_phy0; @@ -288,28 +288,28 @@ static struct pci_driver isp1761_pci_driver = { static int __init isp1760_init(void) { - int ret = -ENODEV; + int ret; init_kmem_once(); -#ifdef CONFIG_USB_ISP1760_OF +#ifdef CONFIG_PPC_OF ret = of_register_platform_driver(&isp1760_of_driver); if (ret) { deinit_kmem_cache(); return ret; } #endif -#ifdef CONFIG_USB_ISP1760_PCI +#ifdef CONFIG_PCI ret = pci_register_driver(&isp1761_pci_driver); if (ret) goto unreg_of; #endif return ret; -#ifdef CONFIG_USB_ISP1760_PCI +#ifdef CONFIG_PCI unreg_of: #endif -#ifdef CONFIG_USB_ISP1760_OF +#ifdef CONFIG_PPC_OF of_unregister_platform_driver(&isp1760_of_driver); #endif deinit_kmem_cache(); @@ -319,10 +319,10 @@ module_init(isp1760_init); static void __exit isp1760_exit(void) { -#ifdef CONFIG_USB_ISP1760_OF +#ifdef CONFIG_PPC_OF of_unregister_platform_driver(&isp1760_of_driver); #endif -#ifdef CONFIG_USB_ISP1760_PCI +#ifdef CONFIG_PCI pci_unregister_driver(&isp1761_pci_driver); #endif deinit_kmem_cache(); diff --git a/drivers/usb/host/ohci-ps3.c b/drivers/usb/host/ohci-ps3.c index 2089d8a..3c1a3b5 100644 --- a/drivers/usb/host/ohci-ps3.c +++ b/drivers/usb/host/ohci-ps3.c @@ -192,7 +192,7 @@ fail_start: return result; } -static int ps3_ohci_remove (struct ps3_system_bus_device *dev) +static int ps3_ohci_remove(struct ps3_system_bus_device *dev) { unsigned int tmp; struct usb_hcd *hcd = @@ -205,6 +205,7 @@ static int ps3_ohci_remove (struct ps3_system_bus_device *dev) tmp = hcd->irq; + ohci_shutdown(hcd); usb_remove_hcd(hcd); ps3_system_bus_set_driver_data(dev, NULL); diff --git a/drivers/usb/host/r8a66597-hcd.c b/drivers/usb/host/r8a66597-hcd.c index c18d879..2376f24 100644 --- a/drivers/usb/host/r8a66597-hcd.c +++ b/drivers/usb/host/r8a66597-hcd.c @@ -1763,11 +1763,12 @@ static void r8a66597_timer(unsigned long _r8a66597) { struct r8a66597 *r8a66597 = (struct r8a66597 *)_r8a66597; unsigned long flags; + int port; spin_lock_irqsave(&r8a66597->lock, flags); - r8a66597_root_hub_control(r8a66597, 0); - r8a66597_root_hub_control(r8a66597, 1); + for (port = 0; port < R8A66597_MAX_ROOT_HUB; port++) + r8a66597_root_hub_control(r8a66597, port); spin_unlock_irqrestore(&r8a66597->lock, flags); } diff --git a/drivers/usb/misc/sisusbvga/sisusb.c b/drivers/usb/misc/sisusbvga/sisusb.c index 69c34a5..b4ec716 100644 --- a/drivers/usb/misc/sisusbvga/sisusb.c +++ b/drivers/usb/misc/sisusbvga/sisusb.c @@ -3270,6 +3270,7 @@ static struct usb_device_id sisusb_table [] = { { USB_DEVICE(0x0711, 0x0900) }, { USB_DEVICE(0x0711, 0x0901) }, { USB_DEVICE(0x0711, 0x0902) }, + { USB_DEVICE(0x0711, 0x0903) }, { USB_DEVICE(0x0711, 0x0918) }, { USB_DEVICE(0x182d, 0x021c) }, { USB_DEVICE(0x182d, 0x0269) }, diff --git a/drivers/usb/misc/vstusb.c b/drivers/usb/misc/vstusb.c index 8648470c..63dff9b 100644 --- a/drivers/usb/misc/vstusb.c +++ b/drivers/usb/misc/vstusb.c @@ -620,7 +620,7 @@ static long vstusb_ioctl(struct file *file, unsigned int cmd, unsigned long arg) __func__); retval = -EFAULT; } else { - dev_dbg(&dev->dev, "%s: recv %d bytes from pipe %d\n", + dev_dbg(&dev->dev, "%s: recv %zd bytes from pipe %d\n", __func__, usb_data.count, usb_data.pipe); } diff --git a/drivers/usb/musb/musb_core.c b/drivers/usb/musb/musb_core.c index 4a35745..5280dba 100644 --- a/drivers/usb/musb/musb_core.c +++ b/drivers/usb/musb/musb_core.c @@ -114,8 +114,8 @@ -unsigned debug; -module_param(debug, uint, S_IRUGO | S_IWUSR); +unsigned musb_debug; +module_param(musb_debug, uint, S_IRUGO | S_IWUSR); MODULE_PARM_DESC(debug, "Debug message level. Default = 0"); #define DRIVER_AUTHOR "Mentor Graphics, Texas Instruments, Nokia" @@ -2248,7 +2248,7 @@ static int __init musb_init(void) "host" #endif ", debug=%d\n", - musb_driver_name, debug); + musb_driver_name, musb_debug); return platform_driver_probe(&musb_driver, musb_probe); } diff --git a/drivers/usb/musb/musb_debug.h b/drivers/usb/musb/musb_debug.h index 4d27944..9fc1db4 100644 --- a/drivers/usb/musb/musb_debug.h +++ b/drivers/usb/musb/musb_debug.h @@ -48,11 +48,11 @@ __func__, __LINE__ , ## args); \ } } while (0) -extern unsigned debug; +extern unsigned musb_debug; static inline int _dbg_level(unsigned l) { - return debug >= l; + return musb_debug >= l; } #define DBG(level, fmt, args...) xprintk(level, KERN_DEBUG, fmt, ## args) diff --git a/drivers/usb/musb/musb_host.c b/drivers/usb/musb/musb_host.c index 3133990..e45e70b 100644 --- a/drivers/usb/musb/musb_host.c +++ b/drivers/usb/musb/musb_host.c @@ -378,6 +378,19 @@ musb_giveback(struct musb_qh *qh, struct urb *urb, int status) switch (qh->type) { + case USB_ENDPOINT_XFER_CONTROL: + case USB_ENDPOINT_XFER_BULK: + /* fifo policy for these lists, except that NAKing + * should rotate a qh to the end (for fairness). + */ + if (qh->mux == 1) { + head = qh->ring.prev; + list_del(&qh->ring); + kfree(qh); + qh = first_qh(head); + break; + } + case USB_ENDPOINT_XFER_ISOC: case USB_ENDPOINT_XFER_INT: /* this is where periodic bandwidth should be @@ -388,17 +401,6 @@ musb_giveback(struct musb_qh *qh, struct urb *urb, int status) kfree(qh); qh = NULL; break; - - case USB_ENDPOINT_XFER_CONTROL: - case USB_ENDPOINT_XFER_BULK: - /* fifo policy for these lists, except that NAKing - * should rotate a qh to the end (for fairness). - */ - head = qh->ring.prev; - list_del(&qh->ring); - kfree(qh); - qh = first_qh(head); - break; } } return qh; @@ -1507,10 +1509,29 @@ void musb_host_rx(struct musb *musb, u8 epnum) musb_writew(hw_ep->regs, MUSB_RXCSR, val); #ifdef CONFIG_USB_INVENTRA_DMA + if (usb_pipeisoc(pipe)) { + struct usb_iso_packet_descriptor *d; + + d = urb->iso_frame_desc + qh->iso_idx; + d->actual_length = xfer_len; + + /* even if there was an error, we did the dma + * for iso_frame_desc->length + */ + if (d->status != EILSEQ && d->status != -EOVERFLOW) + d->status = 0; + + if (++qh->iso_idx >= urb->number_of_packets) + done = true; + else + done = false; + + } else { /* done if urb buffer is full or short packet is recd */ done = (urb->actual_length + xfer_len >= urb->transfer_buffer_length || dma->actual_len < qh->maxpacket); + } /* send IN token for next packet, without AUTOREQ */ if (!done) { @@ -1547,7 +1568,8 @@ void musb_host_rx(struct musb *musb, u8 epnum) if (dma) { struct dma_controller *c; u16 rx_count; - int ret; + int ret, length; + dma_addr_t buf; rx_count = musb_readw(epio, MUSB_RXCOUNT); @@ -1560,6 +1582,35 @@ void musb_host_rx(struct musb *musb, u8 epnum) c = musb->dma_controller; + if (usb_pipeisoc(pipe)) { + int status = 0; + struct usb_iso_packet_descriptor *d; + + d = urb->iso_frame_desc + qh->iso_idx; + + if (iso_err) { + status = -EILSEQ; + urb->error_count++; + } + if (rx_count > d->length) { + if (status == 0) { + status = -EOVERFLOW; + urb->error_count++; + } + DBG(2, "** OVERFLOW %d into %d\n",\ + rx_count, d->length); + + length = d->length; + } else + length = rx_count; + d->status = status; + buf = urb->transfer_dma + d->offset; + } else { + length = rx_count; + buf = urb->transfer_dma + + urb->actual_length; + } + dma->desired_mode = 0; #ifdef USE_MODE1 /* because of the issue below, mode 1 will @@ -1571,6 +1622,12 @@ void musb_host_rx(struct musb *musb, u8 epnum) urb->actual_length) > qh->maxpacket) dma->desired_mode = 1; + if (rx_count < hw_ep->max_packet_sz_rx) { + length = rx_count; + dma->bDesiredMode = 0; + } else { + length = urb->transfer_buffer_length; + } #endif /* Disadvantage of using mode 1: @@ -1608,12 +1665,7 @@ void musb_host_rx(struct musb *musb, u8 epnum) */ ret = c->channel_program( dma, qh->maxpacket, - dma->desired_mode, - urb->transfer_dma - + urb->actual_length, - (dma->desired_mode == 0) - ? rx_count - : urb->transfer_buffer_length); + dma->desired_mode, buf, length); if (!ret) { c->channel_release(dma); @@ -1631,19 +1683,6 @@ void musb_host_rx(struct musb *musb, u8 epnum) } } - if (dma && usb_pipeisoc(pipe)) { - struct usb_iso_packet_descriptor *d; - int iso_stat = status; - - d = urb->iso_frame_desc + qh->iso_idx; - d->actual_length += xfer_len; - if (iso_err) { - iso_stat = -EILSEQ; - urb->error_count++; - } - d->status = iso_stat; - } - finish: urb->actual_length += xfer_len; qh->offset += xfer_len; @@ -1671,22 +1710,9 @@ static int musb_schedule( struct list_head *head = NULL; /* use fixed hardware for control and bulk */ - switch (qh->type) { - case USB_ENDPOINT_XFER_CONTROL: + if (qh->type == USB_ENDPOINT_XFER_CONTROL) { head = &musb->control; hw_ep = musb->control_ep; - break; - case USB_ENDPOINT_XFER_BULK: - hw_ep = musb->bulk_ep; - if (is_in) - head = &musb->in_bulk; - else - head = &musb->out_bulk; - break; - } - if (head) { - idle = list_empty(head); - list_add_tail(&qh->ring, head); goto success; } @@ -1725,19 +1751,34 @@ static int musb_schedule( else diff = hw_ep->max_packet_sz_tx - qh->maxpacket; - if (diff > 0 && best_diff > diff) { + if (diff >= 0 && best_diff > diff) { best_diff = diff; best_end = epnum; } } - if (best_end < 0) + /* use bulk reserved ep1 if no other ep is free */ + if (best_end > 0 && qh->type == USB_ENDPOINT_XFER_BULK) { + hw_ep = musb->bulk_ep; + if (is_in) + head = &musb->in_bulk; + else + head = &musb->out_bulk; + goto success; + } else if (best_end < 0) { return -ENOSPC; + } idle = 1; + qh->mux = 0; hw_ep = musb->endpoints + best_end; musb->periodic[best_end] = qh; DBG(4, "qh %p periodic slot %d\n", qh, best_end); success: + if (head) { + idle = list_empty(head); + list_add_tail(&qh->ring, head); + qh->mux = 1; + } qh->hw_ep = hw_ep; qh->hep->hcpriv = qh; if (idle) @@ -2015,11 +2056,13 @@ static int musb_urb_dequeue(struct usb_hcd *hcd, struct urb *urb, int status) sched = &musb->control; break; case USB_ENDPOINT_XFER_BULK: - if (usb_pipein(urb->pipe)) - sched = &musb->in_bulk; - else - sched = &musb->out_bulk; - break; + if (qh->mux == 1) { + if (usb_pipein(urb->pipe)) + sched = &musb->in_bulk; + else + sched = &musb->out_bulk; + break; + } default: /* REVISIT when we get a schedule tree, periodic * transfers won't always be at the head of a @@ -2067,11 +2110,13 @@ musb_h_disable(struct usb_hcd *hcd, struct usb_host_endpoint *hep) sched = &musb->control; break; case USB_ENDPOINT_XFER_BULK: - if (is_in) - sched = &musb->in_bulk; - else - sched = &musb->out_bulk; - break; + if (qh->mux == 1) { + if (is_in) + sched = &musb->in_bulk; + else + sched = &musb->out_bulk; + break; + } default: /* REVISIT when we get a schedule tree, periodic transfers * won't always be at the head of a singleton queue... diff --git a/drivers/usb/musb/musb_host.h b/drivers/usb/musb/musb_host.h index 77bcdb9..0b7fbcd 100644 --- a/drivers/usb/musb/musb_host.h +++ b/drivers/usb/musb/musb_host.h @@ -53,6 +53,7 @@ struct musb_qh { struct list_head ring; /* of musb_qh */ /* struct musb_qh *next; */ /* for periodic tree */ + u8 mux; /* qh multiplexed to hw_ep */ unsigned offset; /* in urb->transfer_buffer */ unsigned segsize; /* current xfer fragment */ diff --git a/drivers/usb/musb/omap2430.c b/drivers/usb/musb/omap2430.c index 9d2dcb1..ce6c162 100644 --- a/drivers/usb/musb/omap2430.c +++ b/drivers/usb/musb/omap2430.c @@ -53,7 +53,9 @@ static void musb_do_idle(unsigned long _musb) { struct musb *musb = (void *)_musb; unsigned long flags; +#ifdef CONFIG_USB_MUSB_HDRC_HCD u8 power; +#endif u8 devctl; devctl = musb_readb(musb->mregs, MUSB_DEVCTL); diff --git a/drivers/usb/musb/tusb6010.c b/drivers/usb/musb/tusb6010.c index b73b036..ee8fca9 100644 --- a/drivers/usb/musb/tusb6010.c +++ b/drivers/usb/musb/tusb6010.c @@ -605,7 +605,7 @@ void musb_platform_set_mode(struct musb *musb, u8 musb_mode) if (musb->board_mode != MUSB_OTG) { ERR("Changing mode currently only supported in OTG mode\n"); - return; + return -EINVAL; } otg_stat = musb_readl(tbase, TUSB_DEV_OTG_STAT); diff --git a/drivers/usb/serial/cp2101.c b/drivers/usb/serial/cp2101.c index 8008d0b..9035d72 100644 --- a/drivers/usb/serial/cp2101.c +++ b/drivers/usb/serial/cp2101.c @@ -67,6 +67,7 @@ static struct usb_device_id id_table [] = { { USB_DEVICE(0x10C4, 0x800A) }, /* SPORTident BSM7-D-USB main station */ { USB_DEVICE(0x10C4, 0x803B) }, /* Pololu USB-serial converter */ { USB_DEVICE(0x10C4, 0x8053) }, /* Enfora EDG1228 */ + { USB_DEVICE(0x10C4, 0x8054) }, /* Enfora GSM2228 */ { USB_DEVICE(0x10C4, 0x8066) }, /* Argussoft In-System Programmer */ { USB_DEVICE(0x10C4, 0x807A) }, /* Crumb128 board */ { USB_DEVICE(0x10C4, 0x80CA) }, /* Degree Controls Inc */ @@ -85,6 +86,7 @@ static struct usb_device_id id_table [] = { { USB_DEVICE(0x10C4, 0x8218) }, /* Lipowsky Industrie Elektronik GmbH, HARP-1 */ { USB_DEVICE(0x10c4, 0x8293) }, /* Telegesys ETRX2USB */ { USB_DEVICE(0x10C4, 0x8341) }, /* Siemens MC35PU GPRS Modem */ + { USB_DEVICE(0x10C4, 0x83A8) }, /* Amber Wireless AMB2560 */ { USB_DEVICE(0x10C4, 0xEA60) }, /* Silicon Labs factory default */ { USB_DEVICE(0x10C4, 0xEA61) }, /* Silicon Labs factory default */ { USB_DEVICE(0x10C4, 0xF001) }, /* Elan Digital Systems USBscope50 */ diff --git a/drivers/usb/serial/option.c b/drivers/usb/serial/option.c index bd07eaa..6fa1ec4 100644 --- a/drivers/usb/serial/option.c +++ b/drivers/usb/serial/option.c @@ -160,6 +160,11 @@ static int option_send_setup(struct tty_struct *tty, struct usb_serial_port *po #define NOVATELWIRELESS_VENDOR_ID 0x1410 +/* YISO PRODUCTS */ + +#define YISO_VENDOR_ID 0x0EAB +#define YISO_PRODUCT_U893 0xC893 + /* MERLIN EVDO PRODUCTS */ #define NOVATELWIRELESS_PRODUCT_V640 0x1100 #define NOVATELWIRELESS_PRODUCT_V620 0x1110 @@ -408,6 +413,7 @@ static struct usb_device_id option_ids[] = { { USB_DEVICE(AXESSTEL_VENDOR_ID, AXESSTEL_PRODUCT_MV110H) }, { USB_DEVICE(ONDA_VENDOR_ID, ONDA_PRODUCT_MSA501HS) }, { USB_DEVICE(ONDA_VENDOR_ID, ONDA_PRODUCT_ET502HS) }, + { USB_DEVICE(YISO_VENDOR_ID, YISO_PRODUCT_U893) }, { USB_DEVICE(BANDRICH_VENDOR_ID, BANDRICH_PRODUCT_C100_1) }, { USB_DEVICE(BANDRICH_VENDOR_ID, BANDRICH_PRODUCT_C100_2) }, { USB_DEVICE(BANDRICH_VENDOR_ID, BANDRICH_PRODUCT_1004) }, diff --git a/drivers/usb/storage/Kconfig b/drivers/usb/storage/Kconfig index 3d92496..c68b738 100644 --- a/drivers/usb/storage/Kconfig +++ b/drivers/usb/storage/Kconfig @@ -2,8 +2,8 @@ # USB Storage driver configuration # -comment "NOTE: USB_STORAGE enables SCSI, and 'SCSI disk support'" -comment "may also be needed; see USB_STORAGE Help for more information" +comment "NOTE: USB_STORAGE depends on SCSI but BLK_DEV_SD may also be needed;" +comment "see USB_STORAGE Help for more information" depends on USB config USB_STORAGE diff --git a/drivers/usb/storage/unusual_devs.h b/drivers/usb/storage/unusual_devs.h index fb9e20e..d4e5fc8 100644 --- a/drivers/usb/storage/unusual_devs.h +++ b/drivers/usb/storage/unusual_devs.h @@ -253,6 +253,14 @@ UNUSUAL_DEV( 0x0421, 0x006a, 0x0000, 0x0591, US_SC_DEVICE, US_PR_DEVICE, NULL, US_FL_FIX_CAPACITY ), +/* Submitted by Ricky Wong Yung Fei <evilbladewarrior@gmail.com> */ +/* Nokia 7610 Supernova - Too many sectors reported in usb storage mode */ +UNUSUAL_DEV( 0x0421, 0x00f5, 0x0000, 0x0470, + "Nokia", + "7610 Supernova", + US_SC_DEVICE, US_PR_DEVICE, NULL, + US_FL_FIX_CAPACITY ), + /* Reported by Olaf Hering <olh@suse.de> from novell bug #105878 */ UNUSUAL_DEV( 0x0424, 0x0fdc, 0x0210, 0x0210, "SMSC", @@ -418,6 +426,13 @@ UNUSUAL_DEV( 0x04b0, 0x0417, 0x0100, 0x0100, US_SC_DEVICE, US_PR_DEVICE, NULL, US_FL_FIX_CAPACITY), +/* Reported by paul ready <lxtwin@homecall.co.uk> */ +UNUSUAL_DEV( 0x04b0, 0x0419, 0x0100, 0x0200, + "NIKON", + "NIKON DSC D300", + US_SC_DEVICE, US_PR_DEVICE, NULL, + US_FL_FIX_CAPACITY), + /* Reported by Doug Maxey (dwm@austin.ibm.com) */ UNUSUAL_DEV( 0x04b3, 0x4001, 0x0110, 0x0110, "IBM", @@ -1258,6 +1273,13 @@ UNUSUAL_DEV( 0x0839, 0x000a, 0x0001, 0x0001, US_SC_DEVICE, US_PR_DEVICE, NULL, US_FL_FIX_INQUIRY), +/* Reported by Luciano Rocha <luciano@eurotux.com> */ +UNUSUAL_DEV( 0x0840, 0x0082, 0x0001, 0x0001, + "Argosy", + "Storage", + US_SC_DEVICE, US_PR_DEVICE, NULL, + US_FL_FIX_CAPACITY), + /* Entry and supporting patch by Theodore Kilgore <kilgota@auburn.edu>. * Flag will support Bulk devices which use a standards-violating 32-byte * Command Block Wrapper. Here, the "DC2MEGA" cameras (several brands) with |