diff options
Diffstat (limited to 'drivers')
-rw-r--r-- | drivers/ata/Kconfig | 2 | ||||
-rw-r--r-- | drivers/ata/ahci.c | 67 | ||||
-rw-r--r-- | drivers/ata/ahci.h | 27 | ||||
-rw-r--r-- | drivers/ata/ahci_brcmstb.c | 61 | ||||
-rw-r--r-- | drivers/ata/ahci_qoriq.c | 31 | ||||
-rw-r--r-- | drivers/ata/libahci.c | 46 | ||||
-rw-r--r-- | drivers/ata/libata-core.c | 20 | ||||
-rw-r--r-- | drivers/ata/sata_rcar.c | 19 | ||||
-rw-r--r-- | drivers/ata/sata_sx4.c | 2 |
9 files changed, 193 insertions, 82 deletions
diff --git a/drivers/ata/Kconfig b/drivers/ata/Kconfig index 6aaa3f8..861643ea 100644 --- a/drivers/ata/Kconfig +++ b/drivers/ata/Kconfig @@ -100,7 +100,7 @@ config SATA_AHCI_PLATFORM config AHCI_BRCMSTB tristate "Broadcom STB AHCI SATA support" - depends on ARCH_BRCMSTB + depends on ARCH_BRCMSTB || BMIPS_GENERIC help This option enables support for the AHCI SATA3 controller found on STB SoC's. diff --git a/drivers/ata/ahci.c b/drivers/ata/ahci.c index cdfbcc5..594fcab 100644 --- a/drivers/ata/ahci.c +++ b/drivers/ata/ahci.c @@ -1306,15 +1306,13 @@ static inline void ahci_gtf_filter_workaround(struct ata_host *host) #endif /* - * ahci_init_msix() only implements single MSI-X support, not multiple - * MSI-X per-port interrupts. This is needed for host controllers that only - * have MSI-X support implemented, but no MSI or intx. + * ahci_init_msix() - optionally enable per-port MSI-X otherwise defer + * to single msi. */ static int ahci_init_msix(struct pci_dev *pdev, unsigned int n_ports, - struct ahci_host_priv *hpriv) + struct ahci_host_priv *hpriv, unsigned long flags) { - int rc, nvec; - struct msix_entry entry = {}; + int nvec, i, rc; /* Do not init MSI-X if MSI is disabled for the device */ if (hpriv->flags & AHCI_HFLAG_NO_MSI) @@ -1324,22 +1322,39 @@ static int ahci_init_msix(struct pci_dev *pdev, unsigned int n_ports, if (nvec < 0) return nvec; - if (!nvec) { + /* + * Proper MSI-X implementations will have a vector per-port. + * Barring that, we prefer single-MSI over single-MSIX. If this + * check fails (not enough MSI-X vectors for all ports) we will + * be called again with the flag clear iff ahci_init_msi() + * fails. + */ + if (flags & AHCI_HFLAG_MULTI_MSIX) { + if (nvec < n_ports) + return -ENODEV; + nvec = n_ports; + } else if (nvec) { + nvec = 1; + } else { + /* + * Emit dev_err() since this was the non-legacy irq + * method of last resort. + */ rc = -ENODEV; goto fail; } - /* - * There can be more than one vector (e.g. for error detection or - * hdd hotplug). Only the first vector (entry.entry = 0) is used. - */ - rc = pci_enable_msix_exact(pdev, &entry, 1); + for (i = 0; i < nvec; i++) + hpriv->msix[i].entry = i; + rc = pci_enable_msix_exact(pdev, hpriv->msix, nvec); if (rc < 0) goto fail; - hpriv->irq = entry.vector; + if (nvec > 1) + hpriv->flags |= AHCI_HFLAG_MULTI_MSIX; + hpriv->irq = hpriv->msix[0].vector; /* for single msi-x */ - return 1; + return nvec; fail: dev_err(&pdev->dev, "failed to enable MSI-X with error %d, # of vectors: %d\n", @@ -1403,20 +1418,25 @@ static int ahci_init_interrupts(struct pci_dev *pdev, unsigned int n_ports, { int nvec; + /* + * Try to enable per-port MSI-X. If the host is not capable + * fall back to single MSI before finally attempting single + * MSI-X. + */ + nvec = ahci_init_msix(pdev, n_ports, hpriv, AHCI_HFLAG_MULTI_MSIX); + if (nvec >= 0) + return nvec; + nvec = ahci_init_msi(pdev, n_ports, hpriv); if (nvec >= 0) return nvec; - /* - * Currently, MSI-X support only implements single IRQ mode and - * exists for controllers which can't do other types of IRQ. Only - * set it up if MSI fails. - */ - nvec = ahci_init_msix(pdev, n_ports, hpriv); + /* try single-msix */ + nvec = ahci_init_msix(pdev, n_ports, hpriv, 0); if (nvec >= 0) return nvec; - /* lagacy intx interrupts */ + /* legacy intx interrupts */ pci_intx(pdev, 1); hpriv->irq = pdev->irq; @@ -1578,7 +1598,10 @@ static int ahci_init_one(struct pci_dev *pdev, const struct pci_device_id *ent) if (!host) return -ENOMEM; host->private_data = hpriv; - + hpriv->msix = devm_kzalloc(&pdev->dev, + sizeof(struct msix_entry) * n_ports, GFP_KERNEL); + if (!hpriv->msix) + return -ENOMEM; ahci_init_interrupts(pdev, n_ports, hpriv); if (!(hpriv->cap & HOST_CAP_SSS) || ahci_ignore_sss) diff --git a/drivers/ata/ahci.h b/drivers/ata/ahci.h index 45586c1..a4faa43 100644 --- a/drivers/ata/ahci.h +++ b/drivers/ata/ahci.h @@ -35,6 +35,7 @@ #ifndef _AHCI_H #define _AHCI_H +#include <linux/pci.h> #include <linux/clk.h> #include <linux/libata.h> #include <linux/phy/phy.h> @@ -237,11 +238,18 @@ enum { AHCI_HFLAG_DELAY_ENGINE = (1 << 15), /* do not start engine on port start (wait until error-handling stage) */ - AHCI_HFLAG_MULTI_MSI = (1 << 16), /* multiple PCI MSIs */ AHCI_HFLAG_NO_DEVSLP = (1 << 17), /* no device sleep */ AHCI_HFLAG_NO_FBS = (1 << 18), /* no FBS */ AHCI_HFLAG_EDGE_IRQ = (1 << 19), /* HOST_IRQ_STAT behaves as Edge Triggered */ +#ifdef CONFIG_PCI_MSI + AHCI_HFLAG_MULTI_MSI = (1 << 20), /* multiple PCI MSIs */ + AHCI_HFLAG_MULTI_MSIX = (1 << 21), /* per-port MSI-X */ +#else + /* compile out MSI infrastructure */ + AHCI_HFLAG_MULTI_MSI = 0, + AHCI_HFLAG_MULTI_MSIX = 0, +#endif /* ap->flags bits */ @@ -308,7 +316,6 @@ struct ahci_port_priv { unsigned int ncq_saw_d2h:1; unsigned int ncq_saw_dmas:1; unsigned int ncq_saw_sdb:1; - atomic_t intr_status; /* interrupts to handle */ spinlock_t lock; /* protects parent ata_port */ u32 intr_mask; /* interrupts to enable */ bool fbs_supported; /* set iff FBS is supported */ @@ -343,6 +350,7 @@ struct ahci_host_priv { * the PHY position in this array. */ struct phy **phys; + struct msix_entry *msix; /* Optional MSI-X support */ unsigned nports; /* Number of ports */ void *plat_data; /* Other platform data */ unsigned int irq; /* interrupt line */ @@ -354,6 +362,21 @@ struct ahci_host_priv { void (*start_engine)(struct ata_port *ap); }; +#ifdef CONFIG_PCI_MSI +static inline int ahci_irq_vector(struct ahci_host_priv *hpriv, int port) +{ + if (hpriv->flags & AHCI_HFLAG_MULTI_MSIX) + return hpriv->msix[port].vector; + else + return hpriv->irq + port; +} +#else +static inline int ahci_irq_vector(struct ahci_host_priv *hpriv, int port) +{ + return hpriv->irq; +} +#endif + extern int ahci_ignore_sss; extern struct device_attribute *ahci_shost_attrs[]; diff --git a/drivers/ata/ahci_brcmstb.c b/drivers/ata/ahci_brcmstb.c index 14b7305..b36cae2 100644 --- a/drivers/ata/ahci_brcmstb.c +++ b/drivers/ata/ahci_brcmstb.c @@ -52,8 +52,10 @@ #define SATA_TOP_CTRL_2_PHY_GLOBAL_RESET BIT(14) #define SATA_TOP_CTRL_PHY_OFFS 0x8 #define SATA_TOP_MAX_PHYS 2 -#define SATA_TOP_CTRL_SATA_TP_OUT 0x1c -#define SATA_TOP_CTRL_CLIENT_INIT_CTRL 0x20 + +#define SATA_FIRST_PORT_CTRL 0x700 +#define SATA_NEXT_PORT_CTRL_OFFSET 0x80 +#define SATA_PORT_PCTRL6(reg_base) (reg_base + 0x18) /* On big-endian MIPS, buses are reversed to big endian, so switch them back */ #if defined(CONFIG_MIPS) && defined(__BIG_ENDIAN) @@ -69,14 +71,21 @@ (DATA_ENDIAN << DMADESC_ENDIAN_SHIFT) | \ (MMIO_ENDIAN << MMIO_ENDIAN_SHIFT)) +enum brcm_ahci_quirks { + BRCM_AHCI_QUIRK_NO_NCQ = BIT(0), + BRCM_AHCI_QUIRK_SKIP_PHY_ENABLE = BIT(1), +}; + struct brcm_ahci_priv { struct device *dev; void __iomem *top_ctrl; u32 port_mask; + u32 quirks; }; static const struct ata_port_info ahci_brcm_port_info = { - .flags = AHCI_FLAG_COMMON, + .flags = AHCI_FLAG_COMMON | ATA_FLAG_NO_DIPM, + .link_flags = ATA_LFLAG_NO_DB_DELAY, .pio_mask = ATA_PIO4, .udma_mask = ATA_UDMA6, .port_ops = &ahci_platform_ops, @@ -107,6 +116,34 @@ static inline void brcm_sata_writereg(u32 val, void __iomem *addr) writel_relaxed(val, addr); } +static void brcm_sata_alpm_init(struct ahci_host_priv *hpriv) +{ + struct brcm_ahci_priv *priv = hpriv->plat_data; + u32 bus_ctrl, port_ctrl, host_caps; + int i; + + /* Enable support for ALPM */ + bus_ctrl = brcm_sata_readreg(priv->top_ctrl + + SATA_TOP_CTRL_BUS_CTRL); + brcm_sata_writereg(bus_ctrl | OVERRIDE_HWINIT, + priv->top_ctrl + SATA_TOP_CTRL_BUS_CTRL); + host_caps = readl(hpriv->mmio + HOST_CAP); + writel(host_caps | HOST_CAP_ALPM, hpriv->mmio); + brcm_sata_writereg(bus_ctrl, priv->top_ctrl + SATA_TOP_CTRL_BUS_CTRL); + + /* + * Adjust timeout to allow PLL sufficient time to lock while waking + * up from slumber mode. + */ + for (i = 0, port_ctrl = SATA_FIRST_PORT_CTRL; + i < SATA_TOP_MAX_PHYS; + i++, port_ctrl += SATA_NEXT_PORT_CTRL_OFFSET) { + if (priv->port_mask & BIT(i)) + writel(0xff1003fc, + hpriv->mmio + SATA_PORT_PCTRL6(port_ctrl)); + } +} + static void brcm_sata_phy_enable(struct brcm_ahci_priv *priv, int port) { void __iomem *phyctrl = priv->top_ctrl + SATA_TOP_CTRL_PHY_CTRL + @@ -114,6 +151,9 @@ static void brcm_sata_phy_enable(struct brcm_ahci_priv *priv, int port) void __iomem *p; u32 reg; + if (priv->quirks & BRCM_AHCI_QUIRK_SKIP_PHY_ENABLE) + return; + /* clear PHY_DEFAULT_POWER_STATE */ p = phyctrl + SATA_TOP_CTRL_PHY_CTRL_1; reg = brcm_sata_readreg(p); @@ -143,6 +183,9 @@ static void brcm_sata_phy_disable(struct brcm_ahci_priv *priv, int port) void __iomem *p; u32 reg; + if (priv->quirks & BRCM_AHCI_QUIRK_SKIP_PHY_ENABLE) + return; + /* power-off the PHY digital logic */ p = phyctrl + SATA_TOP_CTRL_PHY_CTRL_2; reg = brcm_sata_readreg(p); @@ -230,6 +273,7 @@ static int brcm_ahci_resume(struct device *dev) brcm_sata_init(priv); brcm_sata_phys_enable(priv); + brcm_sata_alpm_init(hpriv); return ahci_platform_resume(dev); } #endif @@ -256,6 +300,11 @@ static int brcm_ahci_probe(struct platform_device *pdev) if (IS_ERR(priv->top_ctrl)) return PTR_ERR(priv->top_ctrl); + if (of_device_is_compatible(dev->of_node, "brcm,bcm7425-ahci")) { + priv->quirks |= BRCM_AHCI_QUIRK_NO_NCQ; + priv->quirks |= BRCM_AHCI_QUIRK_SKIP_PHY_ENABLE; + } + brcm_sata_init(priv); priv->port_mask = brcm_ahci_get_portmask(pdev, priv); @@ -269,10 +318,15 @@ static int brcm_ahci_probe(struct platform_device *pdev) return PTR_ERR(hpriv); hpriv->plat_data = priv; + brcm_sata_alpm_init(hpriv); + ret = ahci_platform_enable_resources(hpriv); if (ret) return ret; + if (priv->quirks & BRCM_AHCI_QUIRK_NO_NCQ) + hpriv->flags |= AHCI_HFLAG_NO_NCQ; + ret = ahci_platform_init_host(pdev, hpriv, &ahci_brcm_port_info, &ahci_platform_sht); if (ret) @@ -300,6 +354,7 @@ static int brcm_ahci_remove(struct platform_device *pdev) } static const struct of_device_id ahci_of_match[] = { + {.compatible = "brcm,bcm7425-ahci"}, {.compatible = "brcm,bcm7445-ahci"}, {}, }; diff --git a/drivers/ata/ahci_qoriq.c b/drivers/ata/ahci_qoriq.c index d0f9de9..7bdee9b 100644 --- a/drivers/ata/ahci_qoriq.c +++ b/drivers/ata/ahci_qoriq.c @@ -34,14 +34,20 @@ /* port register default value */ #define AHCI_PORT_PHY_1_CFG 0xa003fffe -#define AHCI_PORT_PHY_2_CFG 0x28183411 -#define AHCI_PORT_PHY_3_CFG 0x0e081004 -#define AHCI_PORT_PHY_4_CFG 0x00480811 -#define AHCI_PORT_PHY_5_CFG 0x192c96a4 -#define AHCI_PORT_TRANS_CFG 0x08000025 +#define AHCI_PORT_TRANS_CFG 0x08000029 + +/* for ls1021a */ +#define LS1021A_PORT_PHY2 0x28183414 +#define LS1021A_PORT_PHY3 0x0e080e06 +#define LS1021A_PORT_PHY4 0x064a080b +#define LS1021A_PORT_PHY5 0x2aa86470 #define SATA_ECC_DISABLE 0x00020000 +/* for ls1043a */ +#define LS1043A_PORT_PHY2 0x28184d1f +#define LS1043A_PORT_PHY3 0x0e081509 + enum ahci_qoriq_type { AHCI_LS1021A, AHCI_LS1043A, @@ -151,16 +157,23 @@ static int ahci_qoriq_phy_init(struct ahci_host_priv *hpriv) case AHCI_LS1021A: writel(SATA_ECC_DISABLE, qpriv->ecc_addr); writel(AHCI_PORT_PHY_1_CFG, reg_base + PORT_PHY1); - writel(AHCI_PORT_PHY_2_CFG, reg_base + PORT_PHY2); - writel(AHCI_PORT_PHY_3_CFG, reg_base + PORT_PHY3); - writel(AHCI_PORT_PHY_4_CFG, reg_base + PORT_PHY4); - writel(AHCI_PORT_PHY_5_CFG, reg_base + PORT_PHY5); + writel(LS1021A_PORT_PHY2, reg_base + PORT_PHY2); + writel(LS1021A_PORT_PHY3, reg_base + PORT_PHY3); + writel(LS1021A_PORT_PHY4, reg_base + PORT_PHY4); + writel(LS1021A_PORT_PHY5, reg_base + PORT_PHY5); writel(AHCI_PORT_TRANS_CFG, reg_base + PORT_TRANS); break; case AHCI_LS1043A: + writel(AHCI_PORT_PHY_1_CFG, reg_base + PORT_PHY1); + writel(LS1043A_PORT_PHY2, reg_base + PORT_PHY2); + writel(LS1043A_PORT_PHY3, reg_base + PORT_PHY3); + writel(AHCI_PORT_TRANS_CFG, reg_base + PORT_TRANS); + break; + case AHCI_LS2080A: writel(AHCI_PORT_PHY_1_CFG, reg_base + PORT_PHY1); + writel(AHCI_PORT_TRANS_CFG, reg_base + PORT_TRANS); break; } diff --git a/drivers/ata/libahci.c b/drivers/ata/libahci.c index 4665512..d61740e 100644 --- a/drivers/ata/libahci.c +++ b/drivers/ata/libahci.c @@ -43,6 +43,7 @@ #include <scsi/scsi_host.h> #include <scsi/scsi_cmnd.h> #include <linux/libata.h> +#include <linux/pci.h> #include "ahci.h" #include "libata.h" @@ -1804,41 +1805,24 @@ static void ahci_port_intr(struct ata_port *ap) ahci_handle_port_interrupt(ap, port_mmio, status); } -static irqreturn_t ahci_port_thread_fn(int irq, void *dev_instance) +static irqreturn_t ahci_multi_irqs_intr_hard(int irq, void *dev_instance) { struct ata_port *ap = dev_instance; - struct ahci_port_priv *pp = ap->private_data; void __iomem *port_mmio = ahci_port_base(ap); u32 status; - status = atomic_xchg(&pp->intr_status, 0); - if (!status) - return IRQ_NONE; - - spin_lock_bh(ap->lock); - ahci_handle_port_interrupt(ap, port_mmio, status); - spin_unlock_bh(ap->lock); - - return IRQ_HANDLED; -} - -static irqreturn_t ahci_multi_irqs_intr(int irq, void *dev_instance) -{ - struct ata_port *ap = dev_instance; - void __iomem *port_mmio = ahci_port_base(ap); - struct ahci_port_priv *pp = ap->private_data; - u32 status; - VPRINTK("ENTER\n"); status = readl(port_mmio + PORT_IRQ_STAT); writel(status, port_mmio + PORT_IRQ_STAT); - atomic_or(status, &pp->intr_status); + spin_lock(ap->lock); + ahci_handle_port_interrupt(ap, port_mmio, status); + spin_unlock(ap->lock); VPRINTK("EXIT\n"); - return IRQ_WAKE_THREAD; + return IRQ_HANDLED; } static u32 ahci_handle_port_intr(struct ata_host *host, u32 irq_masked) @@ -2479,9 +2463,10 @@ void ahci_set_em_messages(struct ahci_host_priv *hpriv, } EXPORT_SYMBOL_GPL(ahci_set_em_messages); -static int ahci_host_activate_multi_irqs(struct ata_host *host, int irq, +static int ahci_host_activate_multi_irqs(struct ata_host *host, struct scsi_host_template *sht) { + struct ahci_host_priv *hpriv = host->private_data; int i, rc; rc = ata_host_start(host); @@ -2493,6 +2478,7 @@ static int ahci_host_activate_multi_irqs(struct ata_host *host, int irq, */ for (i = 0; i < host->n_ports; i++) { struct ahci_port_priv *pp = host->ports[i]->private_data; + int irq = ahci_irq_vector(hpriv, i); /* Do not receive interrupts sent by dummy ports */ if (!pp) { @@ -2500,14 +2486,14 @@ static int ahci_host_activate_multi_irqs(struct ata_host *host, int irq, continue; } - rc = devm_request_threaded_irq(host->dev, irq + i, - ahci_multi_irqs_intr, - ahci_port_thread_fn, 0, - pp->irq_desc, host->ports[i]); + rc = devm_request_irq(host->dev, irq, ahci_multi_irqs_intr_hard, + 0, pp->irq_desc, host->ports[i]); + if (rc) return rc; - ata_port_desc(host->ports[i], "irq %d", irq + i); + ata_port_desc(host->ports[i], "irq %d", irq); } + return ata_host_register(host, sht); } @@ -2528,8 +2514,8 @@ int ahci_host_activate(struct ata_host *host, struct scsi_host_template *sht) int irq = hpriv->irq; int rc; - if (hpriv->flags & AHCI_HFLAG_MULTI_MSI) - rc = ahci_host_activate_multi_irqs(host, irq, sht); + if (hpriv->flags & (AHCI_HFLAG_MULTI_MSI | AHCI_HFLAG_MULTI_MSIX)) + rc = ahci_host_activate_multi_irqs(host, sht); else if (hpriv->flags & AHCI_HFLAG_EDGE_IRQ) rc = ata_host_activate(host, irq, ahci_single_edge_irq_intr, IRQF_SHARED, sht); diff --git a/drivers/ata/libata-core.c b/drivers/ata/libata-core.c index b79cb10..cbb7471 100644 --- a/drivers/ata/libata-core.c +++ b/drivers/ata/libata-core.c @@ -50,6 +50,7 @@ #include <linux/blkdev.h> #include <linux/delay.h> #include <linux/timer.h> +#include <linux/time.h> #include <linux/interrupt.h> #include <linux/completion.h> #include <linux/suspend.h> @@ -3597,7 +3598,8 @@ int sata_link_resume(struct ata_link *link, const unsigned long *params, * immediately after resuming. Delay 200ms before * debouncing. */ - ata_msleep(link->ap, 200); + if (!(link->flags & ATA_LFLAG_NO_DB_DELAY)) + ata_msleep(link->ap, 200); /* is SControl restored correctly? */ if ((rc = sata_scr_read(link, SCR_CONTROL, &scontrol))) @@ -6223,6 +6225,7 @@ int ata_host_activate(struct ata_host *host, int irq, struct scsi_host_template *sht) { int i, rc; + char *irq_desc; rc = ata_host_start(host); if (rc) @@ -6234,8 +6237,14 @@ int ata_host_activate(struct ata_host *host, int irq, return ata_host_register(host, sht); } + irq_desc = devm_kasprintf(host->dev, GFP_KERNEL, "%s[%s]", + dev_driver_string(host->dev), + dev_name(host->dev)); + if (!irq_desc) + return -ENOMEM; + rc = devm_request_irq(host->dev, irq, irq_handler, irq_flags, - dev_name(host->dev), host); + irq_desc, host); if (rc) return rc; @@ -6697,7 +6706,12 @@ void ata_msleep(struct ata_port *ap, unsigned int msecs) if (owns_eh) ata_eh_release(ap); - msleep(msecs); + if (msecs < 20) { + unsigned long usecs = msecs * USEC_PER_MSEC; + usleep_range(usecs, usecs + 50); + } else { + msleep(msecs); + } if (owns_eh) ata_eh_acquire(ap); diff --git a/drivers/ata/sata_rcar.c b/drivers/ata/sata_rcar.c index 8804127..f72d601 100644 --- a/drivers/ata/sata_rcar.c +++ b/drivers/ata/sata_rcar.c @@ -854,17 +854,14 @@ static struct of_device_id sata_rcar_match[] = { .compatible = "renesas,sata-r8a7793", .data = (void *)RCAR_GEN2_SATA }, + { + .compatible = "renesas,sata-r8a7795", + .data = (void *)RCAR_GEN2_SATA + }, { }, }; MODULE_DEVICE_TABLE(of, sata_rcar_match); -static const struct platform_device_id sata_rcar_id_table[] = { - { "sata_rcar", RCAR_GEN1_SATA }, /* Deprecated by "sata-r8a7779" */ - { "sata-r8a7779", RCAR_GEN1_SATA }, - { }, -}; -MODULE_DEVICE_TABLE(platform, sata_rcar_id_table); - static int sata_rcar_probe(struct platform_device *pdev) { const struct of_device_id *of_id; @@ -884,11 +881,10 @@ static int sata_rcar_probe(struct platform_device *pdev) return -ENOMEM; of_id = of_match_device(sata_rcar_match, &pdev->dev); - if (of_id) - priv->type = (enum sata_rcar_type)of_id->data; - else - priv->type = platform_get_device_id(pdev)->driver_data; + if (!of_id) + return -ENODEV; + priv->type = (enum sata_rcar_type)of_id->data; priv->clk = devm_clk_get(&pdev->dev, NULL); if (IS_ERR(priv->clk)) { dev_err(&pdev->dev, "failed to get access to sata clock\n"); @@ -1018,7 +1014,6 @@ static const struct dev_pm_ops sata_rcar_pm_ops = { static struct platform_driver sata_rcar_driver = { .probe = sata_rcar_probe, .remove = sata_rcar_remove, - .id_table = sata_rcar_id_table, .driver = { .name = DRV_NAME, .of_match_table = sata_rcar_match, diff --git a/drivers/ata/sata_sx4.c b/drivers/ata/sata_sx4.c index fab504f..48301cb 100644 --- a/drivers/ata/sata_sx4.c +++ b/drivers/ata/sata_sx4.c @@ -1396,6 +1396,8 @@ static unsigned int pdc20621_dimm_init(struct ata_host *host) addr = 0; length = size * 1024 * 1024; buf = kzalloc(ECC_ERASE_BUF_SZ, GFP_KERNEL); + if (!buf) + return 1; while (addr < length) { pdc20621_put_to_dimm(host, buf, addr, ECC_ERASE_BUF_SZ); |