diff options
Diffstat (limited to 'drivers')
-rw-r--r-- | drivers/regulator/qcom_spmi-regulator.c | 200 |
1 files changed, 195 insertions, 5 deletions
diff --git a/drivers/regulator/qcom_spmi-regulator.c b/drivers/regulator/qcom_spmi-regulator.c index 9ef0e2f..88a5dc8 100644 --- a/drivers/regulator/qcom_spmi-regulator.c +++ b/drivers/regulator/qcom_spmi-regulator.c @@ -26,6 +26,70 @@ #include <linux/regmap.h> #include <linux/list.h> +/* Pin control enable input pins. */ +#define SPMI_REGULATOR_PIN_CTRL_ENABLE_NONE 0x00 +#define SPMI_REGULATOR_PIN_CTRL_ENABLE_EN0 0x01 +#define SPMI_REGULATOR_PIN_CTRL_ENABLE_EN1 0x02 +#define SPMI_REGULATOR_PIN_CTRL_ENABLE_EN2 0x04 +#define SPMI_REGULATOR_PIN_CTRL_ENABLE_EN3 0x08 +#define SPMI_REGULATOR_PIN_CTRL_ENABLE_HW_DEFAULT 0x10 + +/* Pin control high power mode input pins. */ +#define SPMI_REGULATOR_PIN_CTRL_HPM_NONE 0x00 +#define SPMI_REGULATOR_PIN_CTRL_HPM_EN0 0x01 +#define SPMI_REGULATOR_PIN_CTRL_HPM_EN1 0x02 +#define SPMI_REGULATOR_PIN_CTRL_HPM_EN2 0x04 +#define SPMI_REGULATOR_PIN_CTRL_HPM_EN3 0x08 +#define SPMI_REGULATOR_PIN_CTRL_HPM_SLEEP_B 0x10 +#define SPMI_REGULATOR_PIN_CTRL_HPM_HW_DEFAULT 0x20 + +/* + * Used with enable parameters to specify that hardware default register values + * should be left unaltered. + */ +#define SPMI_REGULATOR_USE_HW_DEFAULT 2 + +/* Soft start strength of a voltage switch type regulator */ +enum spmi_vs_soft_start_str { + SPMI_VS_SOFT_START_STR_0P05_UA = 0, + SPMI_VS_SOFT_START_STR_0P25_UA, + SPMI_VS_SOFT_START_STR_0P55_UA, + SPMI_VS_SOFT_START_STR_0P75_UA, + SPMI_VS_SOFT_START_STR_HW_DEFAULT, +}; + +/** + * struct spmi_regulator_init_data - spmi-regulator initialization data + * @pin_ctrl_enable: Bit mask specifying which hardware pins should be + * used to enable the regulator, if any + * Value should be an ORing of + * SPMI_REGULATOR_PIN_CTRL_ENABLE_* constants. If + * the bit specified by + * SPMI_REGULATOR_PIN_CTRL_ENABLE_HW_DEFAULT is + * set, then pin control enable hardware registers + * will not be modified. + * @pin_ctrl_hpm: Bit mask specifying which hardware pins should be + * used to force the regulator into high power + * mode, if any + * Value should be an ORing of + * SPMI_REGULATOR_PIN_CTRL_HPM_* constants. If + * the bit specified by + * SPMI_REGULATOR_PIN_CTRL_HPM_HW_DEFAULT is + * set, then pin control mode hardware registers + * will not be modified. + * @vs_soft_start_strength: This parameter sets the soft start strength for + * voltage switch type regulators. Its value + * should be one of SPMI_VS_SOFT_START_STR_*. If + * its value is SPMI_VS_SOFT_START_STR_HW_DEFAULT, + * then the soft start strength will be left at its + * default hardware value. + */ +struct spmi_regulator_init_data { + unsigned pin_ctrl_enable; + unsigned pin_ctrl_hpm; + enum spmi_vs_soft_start_str vs_soft_start_strength; +}; + /* These types correspond to unique register layouts. */ enum spmi_regulator_logical_type { SPMI_REGULATOR_LOGICAL_TYPE_SMPS, @@ -458,6 +522,14 @@ static int spmi_regulator_vs_enable(struct regulator_dev *rdev) return spmi_regulator_common_enable(rdev); } +static int spmi_regulator_vs_ocp(struct regulator_dev *rdev) +{ + struct spmi_regulator *vreg = rdev_get_drvdata(rdev); + u8 reg = SPMI_VS_OCP_OVERRIDE; + + return spmi_vreg_write(vreg, SPMI_VS_REG_OCP, ®, 1); +} + static int spmi_regulator_common_disable(struct regulator_dev *rdev) { struct spmi_regulator *vreg = rdev_get_drvdata(rdev); @@ -791,6 +863,9 @@ static unsigned int spmi_regulator_common_get_mode(struct regulator_dev *rdev) if (reg & SPMI_COMMON_MODE_HPM_MASK) return REGULATOR_MODE_NORMAL; + if (reg & SPMI_COMMON_MODE_AUTO_MASK) + return REGULATOR_MODE_FAST; + return REGULATOR_MODE_IDLE; } @@ -798,11 +873,13 @@ static int spmi_regulator_common_set_mode(struct regulator_dev *rdev, unsigned int mode) { struct spmi_regulator *vreg = rdev_get_drvdata(rdev); - u8 mask = SPMI_COMMON_MODE_HPM_MASK; + u8 mask = SPMI_COMMON_MODE_HPM_MASK | SPMI_COMMON_MODE_AUTO_MASK; u8 val = 0; if (mode == REGULATOR_MODE_NORMAL) - val = mask; + val = SPMI_COMMON_MODE_HPM_MASK; + else if (mode == REGULATOR_MODE_FAST) + val = SPMI_COMMON_MODE_AUTO_MASK; return spmi_vreg_update_bits(vreg, SPMI_COMMON_REG_MODE, val, mask); } @@ -972,6 +1049,7 @@ static struct regulator_ops spmi_vs_ops = { .is_enabled = spmi_regulator_common_is_enabled, .set_pull_down = spmi_regulator_common_set_pull_down, .set_soft_start = spmi_regulator_common_set_soft_start, + .set_over_current_protection = spmi_regulator_vs_ocp, }; static struct regulator_ops spmi_boost_ops = { @@ -1202,10 +1280,111 @@ static int spmi_regulator_ftsmps_init_slew_rate(struct spmi_regulator *vreg) return ret; } +static int spmi_regulator_init_registers(struct spmi_regulator *vreg, + const struct spmi_regulator_init_data *data) +{ + int ret; + enum spmi_regulator_logical_type type; + u8 ctrl_reg[8], reg, mask; + + type = vreg->logical_type; + + ret = spmi_vreg_read(vreg, SPMI_COMMON_REG_VOLTAGE_RANGE, ctrl_reg, 8); + if (ret) + return ret; + + /* Set up enable pin control. */ + if ((type == SPMI_REGULATOR_LOGICAL_TYPE_SMPS + || type == SPMI_REGULATOR_LOGICAL_TYPE_LDO + || type == SPMI_REGULATOR_LOGICAL_TYPE_VS) + && !(data->pin_ctrl_enable + & SPMI_REGULATOR_PIN_CTRL_ENABLE_HW_DEFAULT)) { + ctrl_reg[SPMI_COMMON_IDX_ENABLE] &= + ~SPMI_COMMON_ENABLE_FOLLOW_ALL_MASK; + ctrl_reg[SPMI_COMMON_IDX_ENABLE] |= + data->pin_ctrl_enable & SPMI_COMMON_ENABLE_FOLLOW_ALL_MASK; + } + + /* Set up mode pin control. */ + if ((type == SPMI_REGULATOR_LOGICAL_TYPE_SMPS + || type == SPMI_REGULATOR_LOGICAL_TYPE_LDO) + && !(data->pin_ctrl_hpm + & SPMI_REGULATOR_PIN_CTRL_HPM_HW_DEFAULT)) { + ctrl_reg[SPMI_COMMON_IDX_MODE] &= + ~SPMI_COMMON_MODE_FOLLOW_ALL_MASK; + ctrl_reg[SPMI_COMMON_IDX_MODE] |= + data->pin_ctrl_hpm & SPMI_COMMON_MODE_FOLLOW_ALL_MASK; + } + + if (type == SPMI_REGULATOR_LOGICAL_TYPE_VS + && !(data->pin_ctrl_hpm & SPMI_REGULATOR_PIN_CTRL_HPM_HW_DEFAULT)) { + ctrl_reg[SPMI_COMMON_IDX_MODE] &= + ~SPMI_COMMON_MODE_FOLLOW_AWAKE_MASK; + ctrl_reg[SPMI_COMMON_IDX_MODE] |= + data->pin_ctrl_hpm & SPMI_COMMON_MODE_FOLLOW_AWAKE_MASK; + } + + if ((type == SPMI_REGULATOR_LOGICAL_TYPE_ULT_LO_SMPS + || type == SPMI_REGULATOR_LOGICAL_TYPE_ULT_HO_SMPS + || type == SPMI_REGULATOR_LOGICAL_TYPE_ULT_LDO) + && !(data->pin_ctrl_hpm + & SPMI_REGULATOR_PIN_CTRL_HPM_HW_DEFAULT)) { + ctrl_reg[SPMI_COMMON_IDX_MODE] &= + ~SPMI_COMMON_MODE_FOLLOW_AWAKE_MASK; + ctrl_reg[SPMI_COMMON_IDX_MODE] |= + data->pin_ctrl_hpm & SPMI_COMMON_MODE_FOLLOW_AWAKE_MASK; + } + + /* Write back any control register values that were modified. */ + ret = spmi_vreg_write(vreg, SPMI_COMMON_REG_VOLTAGE_RANGE, ctrl_reg, 8); + if (ret) + return ret; + + /* Set soft start strength and over current protection for VS. */ + if (type == SPMI_REGULATOR_LOGICAL_TYPE_VS) { + if (data->vs_soft_start_strength + != SPMI_VS_SOFT_START_STR_HW_DEFAULT) { + reg = data->vs_soft_start_strength + & SPMI_VS_SOFT_START_SEL_MASK; + mask = SPMI_VS_SOFT_START_SEL_MASK; + return spmi_vreg_update_bits(vreg, + SPMI_VS_REG_SOFT_START, + reg, mask); + } + } + + return 0; +} + +static void spmi_regulator_get_dt_config(struct spmi_regulator *vreg, + struct device_node *node, struct spmi_regulator_init_data *data) +{ + /* + * Initialize configuration parameters to use hardware default in case + * no value is specified via device tree. + */ + data->pin_ctrl_enable = SPMI_REGULATOR_PIN_CTRL_ENABLE_HW_DEFAULT; + data->pin_ctrl_hpm = SPMI_REGULATOR_PIN_CTRL_HPM_HW_DEFAULT; + data->vs_soft_start_strength = SPMI_VS_SOFT_START_STR_HW_DEFAULT; + + /* These bindings are optional, so it is okay if they aren't found. */ + of_property_read_u32(node, "qcom,ocp-max-retries", + &vreg->ocp_max_retries); + of_property_read_u32(node, "qcom,ocp-retry-delay", + &vreg->ocp_retry_delay_ms); + of_property_read_u32(node, "qcom,pin-ctrl-enable", + &data->pin_ctrl_enable); + of_property_read_u32(node, "qcom,pin-ctrl-hpm", &data->pin_ctrl_hpm); + of_property_read_u32(node, "qcom,vs-soft-start-strength", + &data->vs_soft_start_strength); +} + static unsigned int spmi_regulator_of_map_mode(unsigned int mode) { - if (mode) + if (mode == 1) return REGULATOR_MODE_NORMAL; + if (mode == 2) + return REGULATOR_MODE_FAST; return REGULATOR_MODE_IDLE; } @@ -1214,12 +1393,23 @@ static int spmi_regulator_of_parse(struct device_node *node, const struct regulator_desc *desc, struct regulator_config *config) { + struct spmi_regulator_init_data data = { }; struct spmi_regulator *vreg = config->driver_data; struct device *dev = config->dev; int ret; - vreg->ocp_max_retries = SPMI_VS_OCP_DEFAULT_MAX_RETRIES; - vreg->ocp_retry_delay_ms = SPMI_VS_OCP_DEFAULT_RETRY_DELAY_MS; + spmi_regulator_get_dt_config(vreg, node, &data); + + if (!vreg->ocp_max_retries) + vreg->ocp_max_retries = SPMI_VS_OCP_DEFAULT_MAX_RETRIES; + if (!vreg->ocp_retry_delay_ms) + vreg->ocp_retry_delay_ms = SPMI_VS_OCP_DEFAULT_RETRY_DELAY_MS; + + ret = spmi_regulator_init_registers(vreg, &data); + if (ret) { + dev_err(dev, "common initialization failed, ret=%d\n", ret); + return ret; + } if (vreg->logical_type == SPMI_REGULATOR_LOGICAL_TYPE_FTSMPS) { ret = spmi_regulator_ftsmps_init_slew_rate(vreg); |