diff options
Diffstat (limited to 'include/asm-sh/smc37c93x.h')
| -rw-r--r-- | include/asm-sh/smc37c93x.h | 190 |
1 files changed, 0 insertions, 190 deletions
diff --git a/include/asm-sh/smc37c93x.h b/include/asm-sh/smc37c93x.h deleted file mode 100644 index 585da2a..0000000 --- a/include/asm-sh/smc37c93x.h +++ /dev/null @@ -1,190 +0,0 @@ -#ifndef __ASM_SH_SMC37C93X_H -#define __ASM_SH_SMC37C93X_H - -/* - * linux/include/asm-sh/smc37c93x.h - * - * Copyright (C) 2000 Kazumoto Kojima - * - * SMSC 37C93x Super IO Chip support - */ - -/* Default base I/O address */ -#define FDC_PRIMARY_BASE 0x3f0 -#define IDE1_PRIMARY_BASE 0x1f0 -#define IDE1_SECONDARY_BASE 0x170 -#define PARPORT_PRIMARY_BASE 0x378 -#define COM1_PRIMARY_BASE 0x2f8 -#define COM2_PRIMARY_BASE 0x3f8 -#define RTC_PRIMARY_BASE 0x070 -#define KBC_PRIMARY_BASE 0x060 -#define AUXIO_PRIMARY_BASE 0x000 /* XXX */ - -/* Logical device number */ -#define LDN_FDC 0 -#define LDN_IDE1 1 -#define LDN_IDE2 2 -#define LDN_PARPORT 3 -#define LDN_COM1 4 -#define LDN_COM2 5 -#define LDN_RTC 6 -#define LDN_KBC 7 -#define LDN_AUXIO 8 - -/* Configuration port and key */ -#define CONFIG_PORT 0x3f0 -#define INDEX_PORT CONFIG_PORT -#define DATA_PORT 0x3f1 -#define CONFIG_ENTER 0x55 -#define CONFIG_EXIT 0xaa - -/* Configuration index */ -#define CURRENT_LDN_INDEX 0x07 -#define POWER_CONTROL_INDEX 0x22 -#define ACTIVATE_INDEX 0x30 -#define IO_BASE_HI_INDEX 0x60 -#define IO_BASE_LO_INDEX 0x61 -#define IRQ_SELECT_INDEX 0x70 -#define DMA_SELECT_INDEX 0x74 - -#define GPIO46_INDEX 0xc6 -#define GPIO47_INDEX 0xc7 - -/* UART stuff. Only for debugging. */ -/* UART Register */ - -#define UART_RBR 0x0 /* Receiver Buffer Register (Read Only) */ -#define UART_THR 0x0 /* Transmitter Holding Register (Write Only) */ -#define UART_IER 0x2 /* Interrupt Enable Register */ -#define UART_IIR 0x4 /* Interrupt Ident Register (Read Only) */ -#define UART_FCR 0x4 /* FIFO Control Register (Write Only) */ -#define UART_LCR 0x6 /* Line Control Register */ -#define UART_MCR 0x8 /* MODEM Control Register */ -#define UART_LSR 0xa /* Line Status Register */ -#define UART_MSR 0xc /* MODEM Status Register */ -#define UART_SCR 0xe /* Scratch Register */ -#define UART_DLL 0x0 /* Divisor Latch (LS) */ -#define UART_DLM 0x2 /* Divisor Latch (MS) */ - -#ifndef __ASSEMBLY__ -typedef struct uart_reg { - volatile __u16 rbr; - volatile __u16 ier; - volatile __u16 iir; - volatile __u16 lcr; - volatile __u16 mcr; - volatile __u16 lsr; - volatile __u16 msr; - volatile __u16 scr; -} uart_reg; -#endif /* ! __ASSEMBLY__ */ - -/* Alias for Write Only Register */ - -#define thr rbr -#define tcr iir - -/* Alias for Divisor Latch Register */ - -#define dll rbr -#define dlm ier -#define fcr iir - -/* Interrupt Enable Register */ - -#define IER_ERDAI 0x0100 /* Enable Received Data Available Interrupt */ -#define IER_ETHREI 0x0200 /* Enable Transmitter Holding Register Empty Interrupt */ -#define IER_ELSI 0x0400 /* Enable Receiver Line Status Interrupt */ -#define IER_EMSI 0x0800 /* Enable MODEM Status Interrupt */ - -/* Interrupt Ident Register */ - -#define IIR_IP 0x0100 /* "0" if Interrupt Pending */ -#define IIR_IIB0 0x0200 /* Interrupt ID Bit 0 */ -#define IIR_IIB1 0x0400 /* Interrupt ID Bit 1 */ -#define IIR_IIB2 0x0800 /* Interrupt ID Bit 2 */ -#define IIR_FIFO 0xc000 /* FIFOs enabled */ - -/* FIFO Control Register */ - -#define FCR_FEN 0x0100 /* FIFO enable */ -#define FCR_RFRES 0x0200 /* Receiver FIFO reset */ -#define FCR_TFRES 0x0400 /* Transmitter FIFO reset */ -#define FCR_DMA 0x0800 /* DMA mode select */ -#define FCR_RTL 0x4000 /* Receiver triger (LSB) */ -#define FCR_RTM 0x8000 /* Receiver triger (MSB) */ - -/* Line Control Register */ - -#define LCR_WLS0 0x0100 /* Word Length Select Bit 0 */ -#define LCR_WLS1 0x0200 /* Word Length Select Bit 1 */ -#define LCR_STB 0x0400 /* Number of Stop Bits */ -#define LCR_PEN 0x0800 /* Parity Enable */ -#define LCR_EPS 0x1000 /* Even Parity Select */ -#define LCR_SP 0x2000 /* Stick Parity */ -#define LCR_SB 0x4000 /* Set Break */ -#define LCR_DLAB 0x8000 /* Divisor Latch Access Bit */ - -/* MODEM Control Register */ - -#define MCR_DTR 0x0100 /* Data Terminal Ready */ -#define MCR_RTS 0x0200 /* Request to Send */ -#define MCR_OUT1 0x0400 /* Out 1 */ -#define MCR_IRQEN 0x0800 /* IRQ Enable */ -#define MCR_LOOP 0x1000 /* Loop */ - -/* Line Status Register */ - -#define LSR_DR 0x0100 /* Data Ready */ -#define LSR_OE 0x0200 /* Overrun Error */ -#define LSR_PE 0x0400 /* Parity Error */ -#define LSR_FE 0x0800 /* Framing Error */ -#define LSR_BI 0x1000 /* Break Interrupt */ -#define LSR_THRE 0x2000 /* Transmitter Holding Register Empty */ -#define LSR_TEMT 0x4000 /* Transmitter Empty */ -#define LSR_FIFOE 0x8000 /* Receiver FIFO error */ - -/* MODEM Status Register */ - -#define MSR_DCTS 0x0100 /* Delta Clear to Send */ -#define MSR_DDSR 0x0200 /* Delta Data Set Ready */ -#define MSR_TERI 0x0400 /* Trailing Edge Ring Indicator */ -#define MSR_DDCD 0x0800 /* Delta Data Carrier Detect */ -#define MSR_CTS 0x1000 /* Clear to Send */ -#define MSR_DSR 0x2000 /* Data Set Ready */ -#define MSR_RI 0x4000 /* Ring Indicator */ -#define MSR_DCD 0x8000 /* Data Carrier Detect */ - -/* Baud Rate Divisor */ - -#define UART_CLK (1843200) /* 1.8432 MHz */ -#define UART_BAUD(x) (UART_CLK / (16 * (x))) - -/* RTC register definition */ -#define RTC_SECONDS 0 -#define RTC_SECONDS_ALARM 1 -#define RTC_MINUTES 2 -#define RTC_MINUTES_ALARM 3 -#define RTC_HOURS 4 -#define RTC_HOURS_ALARM 5 -#define RTC_DAY_OF_WEEK 6 -#define RTC_DAY_OF_MONTH 7 -#define RTC_MONTH 8 -#define RTC_YEAR 9 -#define RTC_FREQ_SELECT 10 -# define RTC_UIP 0x80 -# define RTC_DIV_CTL 0x70 -/* This RTC can work under 32.768KHz clock only. */ -# define RTC_OSC_ENABLE 0x20 -# define RTC_OSC_DISABLE 0x00 -#define RTC_CONTROL 11 -# define RTC_SET 0x80 -# define RTC_PIE 0x40 -# define RTC_AIE 0x20 -# define RTC_UIE 0x10 -# define RTC_SQWE 0x08 -# define RTC_DM_BINARY 0x04 -# define RTC_24H 0x02 -# define RTC_DST_EN 0x01 - -#endif /* __ASM_SH_SMC37C93X_H */ |