diff options
Diffstat (limited to 'sound')
| -rw-r--r-- | sound/soc/codecs/wm8962.c | 226 |
1 files changed, 116 insertions, 110 deletions
diff --git a/sound/soc/codecs/wm8962.c b/sound/soc/codecs/wm8962.c index 22e42e7..ac1ff99 100644 --- a/sound/soc/codecs/wm8962.c +++ b/sound/soc/codecs/wm8962.c @@ -1758,6 +1758,9 @@ SOC_DOUBLE_R_TLV("EQ4 Volume", WM8962_EQ3, WM8962_EQ23, WM8962_EQL_B4_GAIN_SHIFT, 31, 0, eq_tlv), SOC_DOUBLE_R_TLV("EQ5 Volume", WM8962_EQ3, WM8962_EQ23, WM8962_EQL_B5_GAIN_SHIFT, 31, 0, eq_tlv), +SND_SOC_BYTES("EQL Coefficients", WM8962_EQ4, 18), +SND_SOC_BYTES("EQR Coefficients", WM8962_EQ24, 18), + SOC_SINGLE("3D Switch", WM8962_THREED1, 0, 1, 0), SND_SOC_BYTES_MASK("3D Coefficients", WM8962_THREED1, 4, WM8962_THREED_ENA), @@ -1775,6 +1778,11 @@ WM8962_DSP2_ENABLE("HPF2 Switch", WM8962_HPF2_ENA_SHIFT), SND_SOC_BYTES("HPF Coefficients", WM8962_LHPF2, 1), WM8962_DSP2_ENABLE("HD Bass Switch", WM8962_HDBASS_ENA_SHIFT), SND_SOC_BYTES("HD Bass Coefficients", WM8962_HDBASS_AI_1, 30), + +SOC_DOUBLE("ALC Switch", WM8962_ALC1, WM8962_ALCL_ENA_SHIFT, + WM8962_ALCR_ENA_SHIFT, 1, 0), +SND_SOC_BYTES_MASK("ALC Coefficients", WM8962_ALC1, 4, + WM8962_ALCL_ENA_MASK | WM8962_ALCR_ENA_MASK), }; static const struct snd_kcontrol_new wm8962_spk_mono_controls[] = { @@ -3242,7 +3250,7 @@ static void wm8962_free_beep(struct snd_soc_codec *codec) } #endif -static void wm8962_set_gpio_mode(struct snd_soc_codec *codec, int gpio) +static void wm8962_set_gpio_mode(struct wm8962_priv *wm8962, int gpio) { int mask = 0; int val = 0; @@ -3263,8 +3271,8 @@ static void wm8962_set_gpio_mode(struct snd_soc_codec *codec, int gpio) } if (mask) - snd_soc_update_bits(codec, WM8962_ANALOGUE_CLOCKING1, - mask, val); + regmap_update_bits(wm8962->regmap, WM8962_ANALOGUE_CLOCKING1, + mask, val); } #ifdef CONFIG_GPIOLIB @@ -3276,7 +3284,6 @@ static inline struct wm8962_priv *gpio_to_wm8962(struct gpio_chip *chip) static int wm8962_gpio_request(struct gpio_chip *chip, unsigned offset) { struct wm8962_priv *wm8962 = gpio_to_wm8962(chip); - struct snd_soc_codec *codec = wm8962->codec; /* The WM8962 GPIOs aren't linearly numbered. For simplicity * we export linear numbers and error out if the unsupported @@ -3292,7 +3299,7 @@ static int wm8962_gpio_request(struct gpio_chip *chip, unsigned offset) return -EINVAL; } - wm8962_set_gpio_mode(codec, offset + 1); + wm8962_set_gpio_mode(wm8962, offset + 1); return 0; } @@ -3376,8 +3383,7 @@ static int wm8962_probe(struct snd_soc_codec *codec) { int ret; struct wm8962_priv *wm8962 = snd_soc_codec_get_drvdata(codec); - struct wm8962_pdata *pdata = &wm8962->pdata; - int i, trigger, irq_pol; + int i; bool dmicclk, dmicdat; wm8962->codec = codec; @@ -3409,75 +3415,6 @@ static int wm8962_probe(struct snd_soc_codec *codec) } } - /* SYSCLK defaults to on; make sure it is off so we can safely - * write to registers if the device is declocked. - */ - snd_soc_update_bits(codec, WM8962_CLOCKING2, WM8962_SYSCLK_ENA, 0); - - /* Ensure we have soft control over all registers */ - snd_soc_update_bits(codec, WM8962_CLOCKING2, - WM8962_CLKREG_OVD, WM8962_CLKREG_OVD); - - /* Ensure that the oscillator and PLLs are disabled */ - snd_soc_update_bits(codec, WM8962_PLL2, - WM8962_OSC_ENA | WM8962_PLL2_ENA | WM8962_PLL3_ENA, - 0); - - /* Apply static configuration for GPIOs */ - for (i = 0; i < ARRAY_SIZE(pdata->gpio_init); i++) - if (pdata->gpio_init[i]) { - wm8962_set_gpio_mode(codec, i + 1); - snd_soc_write(codec, 0x200 + i, - pdata->gpio_init[i] & 0xffff); - } - - - /* Put the speakers into mono mode? */ - if (pdata->spk_mono) - snd_soc_update_bits(codec, WM8962_CLASS_D_CONTROL_2, - WM8962_SPK_MONO_MASK, WM8962_SPK_MONO); - - /* Micbias setup, detection enable and detection - * threasholds. */ - if (pdata->mic_cfg) - snd_soc_update_bits(codec, WM8962_ADDITIONAL_CONTROL_4, - WM8962_MICDET_ENA | - WM8962_MICDET_THR_MASK | - WM8962_MICSHORT_THR_MASK | - WM8962_MICBIAS_LVL, - pdata->mic_cfg); - - /* Latch volume update bits */ - snd_soc_update_bits(codec, WM8962_LEFT_INPUT_VOLUME, - WM8962_IN_VU, WM8962_IN_VU); - snd_soc_update_bits(codec, WM8962_RIGHT_INPUT_VOLUME, - WM8962_IN_VU, WM8962_IN_VU); - snd_soc_update_bits(codec, WM8962_LEFT_ADC_VOLUME, - WM8962_ADC_VU, WM8962_ADC_VU); - snd_soc_update_bits(codec, WM8962_RIGHT_ADC_VOLUME, - WM8962_ADC_VU, WM8962_ADC_VU); - snd_soc_update_bits(codec, WM8962_LEFT_DAC_VOLUME, - WM8962_DAC_VU, WM8962_DAC_VU); - snd_soc_update_bits(codec, WM8962_RIGHT_DAC_VOLUME, - WM8962_DAC_VU, WM8962_DAC_VU); - snd_soc_update_bits(codec, WM8962_SPKOUTL_VOLUME, - WM8962_SPKOUT_VU, WM8962_SPKOUT_VU); - snd_soc_update_bits(codec, WM8962_SPKOUTR_VOLUME, - WM8962_SPKOUT_VU, WM8962_SPKOUT_VU); - snd_soc_update_bits(codec, WM8962_HPOUTL_VOLUME, - WM8962_HPOUT_VU, WM8962_HPOUT_VU); - snd_soc_update_bits(codec, WM8962_HPOUTR_VOLUME, - WM8962_HPOUT_VU, WM8962_HPOUT_VU); - - /* Stereo control for EQ */ - snd_soc_update_bits(codec, WM8962_EQ1, WM8962_EQ_SHARED_COEFF, 0); - - /* Don't debouce interrupts so we don't need SYSCLK */ - snd_soc_update_bits(codec, WM8962_IRQ_DEBOUNCE, - WM8962_FLL_LOCK_DB | WM8962_PLL3_LOCK_DB | - WM8962_PLL2_LOCK_DB | WM8962_TEMP_SHUT_DB, - 0); - wm8962_add_widgets(codec); /* Save boards having to disable DMIC when not in use */ @@ -3506,36 +3443,6 @@ static int wm8962_probe(struct snd_soc_codec *codec) wm8962_init_beep(codec); wm8962_init_gpio(codec); - if (wm8962->irq) { - if (pdata->irq_active_low) { - trigger = IRQF_TRIGGER_LOW; - irq_pol = WM8962_IRQ_POL; - } else { - trigger = IRQF_TRIGGER_HIGH; - irq_pol = 0; - } - - snd_soc_update_bits(codec, WM8962_INTERRUPT_CONTROL, - WM8962_IRQ_POL, irq_pol); - - ret = request_threaded_irq(wm8962->irq, NULL, wm8962_irq, - trigger | IRQF_ONESHOT, - "wm8962", codec->dev); - if (ret != 0) { - dev_err(codec->dev, "Failed to request IRQ %d: %d\n", - wm8962->irq, ret); - wm8962->irq = 0; - /* Non-fatal */ - } else { - /* Enable some IRQs by default */ - snd_soc_update_bits(codec, - WM8962_INTERRUPT_STATUS_2_MASK, - WM8962_FLL_LOCK_EINT | - WM8962_TEMP_SHUT_EINT | - WM8962_FIFOS_ERR_EINT, 0); - } - } - return 0; } @@ -3544,9 +3451,6 @@ static int wm8962_remove(struct snd_soc_codec *codec) struct wm8962_priv *wm8962 = snd_soc_codec_get_drvdata(codec); int i; - if (wm8962->irq) - free_irq(wm8962->irq, codec); - cancel_delayed_work_sync(&wm8962->mic_work); wm8962_free_gpio(codec); @@ -3619,7 +3523,7 @@ static int wm8962_i2c_probe(struct i2c_client *i2c, struct wm8962_pdata *pdata = dev_get_platdata(&i2c->dev); struct wm8962_priv *wm8962; unsigned int reg; - int ret, i; + int ret, i, irq_pol, trigger; wm8962 = devm_kzalloc(&i2c->dev, sizeof(struct wm8962_priv), GFP_KERNEL); @@ -3704,6 +3608,77 @@ static int wm8962_i2c_probe(struct i2c_client *i2c, goto err_enable; } + /* SYSCLK defaults to on; make sure it is off so we can safely + * write to registers if the device is declocked. + */ + regmap_update_bits(wm8962->regmap, WM8962_CLOCKING2, + WM8962_SYSCLK_ENA, 0); + + /* Ensure we have soft control over all registers */ + regmap_update_bits(wm8962->regmap, WM8962_CLOCKING2, + WM8962_CLKREG_OVD, WM8962_CLKREG_OVD); + + /* Ensure that the oscillator and PLLs are disabled */ + regmap_update_bits(wm8962->regmap, WM8962_PLL2, + WM8962_OSC_ENA | WM8962_PLL2_ENA | WM8962_PLL3_ENA, + 0); + + /* Apply static configuration for GPIOs */ + for (i = 0; i < ARRAY_SIZE(wm8962->pdata.gpio_init); i++) + if (wm8962->pdata.gpio_init[i]) { + wm8962_set_gpio_mode(wm8962, i + 1); + regmap_write(wm8962->regmap, 0x200 + i, + wm8962->pdata.gpio_init[i] & 0xffff); + } + + + /* Put the speakers into mono mode? */ + if (wm8962->pdata.spk_mono) + regmap_update_bits(wm8962->regmap, WM8962_CLASS_D_CONTROL_2, + WM8962_SPK_MONO_MASK, WM8962_SPK_MONO); + + /* Micbias setup, detection enable and detection + * threasholds. */ + if (wm8962->pdata.mic_cfg) + regmap_update_bits(wm8962->regmap, WM8962_ADDITIONAL_CONTROL_4, + WM8962_MICDET_ENA | + WM8962_MICDET_THR_MASK | + WM8962_MICSHORT_THR_MASK | + WM8962_MICBIAS_LVL, + wm8962->pdata.mic_cfg); + + /* Latch volume update bits */ + regmap_update_bits(wm8962->regmap, WM8962_LEFT_INPUT_VOLUME, + WM8962_IN_VU, WM8962_IN_VU); + regmap_update_bits(wm8962->regmap, WM8962_RIGHT_INPUT_VOLUME, + WM8962_IN_VU, WM8962_IN_VU); + regmap_update_bits(wm8962->regmap, WM8962_LEFT_ADC_VOLUME, + WM8962_ADC_VU, WM8962_ADC_VU); + regmap_update_bits(wm8962->regmap, WM8962_RIGHT_ADC_VOLUME, + WM8962_ADC_VU, WM8962_ADC_VU); + regmap_update_bits(wm8962->regmap, WM8962_LEFT_DAC_VOLUME, + WM8962_DAC_VU, WM8962_DAC_VU); + regmap_update_bits(wm8962->regmap, WM8962_RIGHT_DAC_VOLUME, + WM8962_DAC_VU, WM8962_DAC_VU); + regmap_update_bits(wm8962->regmap, WM8962_SPKOUTL_VOLUME, + WM8962_SPKOUT_VU, WM8962_SPKOUT_VU); + regmap_update_bits(wm8962->regmap, WM8962_SPKOUTR_VOLUME, + WM8962_SPKOUT_VU, WM8962_SPKOUT_VU); + regmap_update_bits(wm8962->regmap, WM8962_HPOUTL_VOLUME, + WM8962_HPOUT_VU, WM8962_HPOUT_VU); + regmap_update_bits(wm8962->regmap, WM8962_HPOUTR_VOLUME, + WM8962_HPOUT_VU, WM8962_HPOUT_VU); + + /* Stereo control for EQ */ + regmap_update_bits(wm8962->regmap, WM8962_EQ1, + WM8962_EQ_SHARED_COEFF, 0); + + /* Don't debouce interrupts so we don't need SYSCLK */ + regmap_update_bits(wm8962->regmap, WM8962_IRQ_DEBOUNCE, + WM8962_FLL_LOCK_DB | WM8962_PLL3_LOCK_DB | + WM8962_PLL2_LOCK_DB | WM8962_TEMP_SHUT_DB, + 0); + if (wm8962->pdata.in4_dc_measure) { ret = regmap_register_patch(wm8962->regmap, wm8962_dc_measure, @@ -3714,6 +3689,37 @@ static int wm8962_i2c_probe(struct i2c_client *i2c, ret); } + if (wm8962->irq) { + if (wm8962->pdata.irq_active_low) { + trigger = IRQF_TRIGGER_LOW; + irq_pol = WM8962_IRQ_POL; + } else { + trigger = IRQF_TRIGGER_HIGH; + irq_pol = 0; + } + + regmap_update_bits(wm8962->regmap, WM8962_INTERRUPT_CONTROL, + WM8962_IRQ_POL, irq_pol); + + ret = devm_request_threaded_irq(&i2c->dev, wm8962->irq, NULL, + wm8962_irq, + trigger | IRQF_ONESHOT, + "wm8962", &i2c->dev); + if (ret != 0) { + dev_err(&i2c->dev, "Failed to request IRQ %d: %d\n", + wm8962->irq, ret); + wm8962->irq = 0; + /* Non-fatal */ + } else { + /* Enable some IRQs by default */ + regmap_update_bits(wm8962->regmap, + WM8962_INTERRUPT_STATUS_2_MASK, + WM8962_FLL_LOCK_EINT | + WM8962_TEMP_SHUT_EINT | + WM8962_FIFOS_ERR_EINT, 0); + } + } + pm_runtime_enable(&i2c->dev); pm_request_idle(&i2c->dev); |