| Age | Commit message (Collapse) | Author |
|---|
|
Suggested-by: Scott Feldman <sfeldma@gmail.com>
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Acked-by: Scott Feldman <sfeldma@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
rocker supports the transmission of scattered packets, so let the kernel
know about it by setting the NETIF_F_SG bit in the device's features.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Acked-by: Scott Feldman <sfeldma@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add skb->hash to the __sk_buff offset map, so it can be accessed from
an eBPF program. We currently already do this for classic BPF filters,
but not yet on eBPF, it might be useful as a demuxer in combination with
helpers like bpf_clone_redirect(), toy example:
__section("cls-lb") int ingress_main(struct __sk_buff *skb)
{
unsigned int which = 3 + (skb->hash & 7);
/* bpf_skb_store_bytes(skb, ...); */
/* bpf_l{3,4}_csum_replace(skb, ...); */
bpf_clone_redirect(skb, which, 0);
return -1;
}
I was thinking whether to add skb_get_hash(), but then concluded the
raw skb->hash seems fine in this case: we can directly access the hash
w/o extra eBPF helper function call, it's filled out by many NICs on
ingress, and in case the entropy level would not be sufficient, people
can still implement their own specific sw fallback hash mix anyway.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Commit 05cc5a39ddb7 ("bnx2x: add vlan filtering offload") has introduced
an incorrect logic for checking whether pvid should be configured for
a vf, causing the hypervisor driver to send unneeded ramrods for all of
the vfs each time a pvid has changed.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: Ariel Elior <Ariel.Elior@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Conflicts:
arch/s390/net/bpf_jit_comp.c
drivers/net/ethernet/ti/netcp_ethss.c
net/bridge/br_multicast.c
net/ipv4/ip_fragment.c
All four conflicts were cases of simple overlapping
changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Pull networking fixes from David Miller:
1) Must teardown SR-IOV before unregistering netdev in igb driver, from
Alex Williamson.
2) Fix ipv6 route unreachable crash in IPVS, from Alex Gartrell.
3) Default route selection in ipv4 should take the prefix length, table
ID, and TOS into account, from Julian Anastasov.
4) sch_plug must have a reset method in order to purge all buffered
packets when the qdisc is reset, likewise for sch_choke, from WANG
Cong.
5) Fix deadlock and races in slave_changelink/br_setport in bridging.
From Nikolay Aleksandrov.
6) mlx4 bug fixes (wrong index in port even propagation to VFs,
overzealous BUG_ON assertion, etc.) from Ido Shamay, Jack
Morgenstein, and Or Gerlitz.
7) Turn off klog message about SCTP userspace interface compat that
makes no sense at all, from Daniel Borkmann.
8) Fix unbounded restarts of inet frag eviction process, causing NMI
watchdog soft lockup messages, from Florian Westphal.
9) Suspend/resume fixes for r8152 from Hayes Wang.
10) Fix busy loop when MSG_WAITALL|MSG_PEEK is used in TCP recv, from
Sabrina Dubroca.
11) Fix performance regression when removing a lot of routes from the
ipv4 routing tables, from Alexander Duyck.
12) Fix device leak in AF_PACKET, from Lars Westerhoff.
13) AF_PACKET also has a header length comparison bug due to signedness,
from Alexander Drozdov.
14) Fix bug in EBPF tail call generation on x86, from Daniel Borkmann.
15) Memory leaks, TSO stats, watchdog timeout and other fixes to
thunderx driver from Sunil Goutham and Thanneeru Srinivasulu.
16) act_bpf can leak memory when replacing programs, from Daniel
Borkmann.
17) WOL packet fixes in gianfar driver, from Claudiu Manoil.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (79 commits)
stmmac: fix missing MODULE_LICENSE in stmmac_platform
gianfar: Enable device wakeup when appropriate
gianfar: Fix suspend/resume for wol magic packet
gianfar: Fix warning when CONFIG_PM off
act_pedit: check binding before calling tcf_hash_release()
net: sk_clone_lock() should only do get_net() if the parent is not a kernel socket
net: sched: fix refcount imbalance in actions
r8152: reset device when tx timeout
r8152: add pre_reset and post_reset
qlcnic: Fix corruption while copying
act_bpf: fix memory leaks when replacing bpf programs
net: thunderx: Fix for crash while BGX teardown
net: thunderx: Add PCI driver shutdown routine
net: thunderx: Fix crash when changing rss with mutliple traffic flows
net: thunderx: Set watchdog timeout value
net: thunderx: Wakeup TXQ only if CQE_TX are processed
net: thunderx: Suppress alloc_pages() failure warnings
net: thunderx: Fix TSO packet statistic
net: thunderx: Fix memory leak when changing queue count
net: thunderx: Fix RQ_DROP miscalculation
...
|
|
Tom Herbert says:
====================
ipv6: Turn on auto IPv6 flow labels by default
BSD (MacOS) has already turned on flow labels by default and this does
not seem to be causing any problems in the Internet. Let's go ahead
and turn them on by default. We'll continue to monitor for any devices
start choking on them.
Flow labels are important since they are the desired solution for
network devices to perform ECMP and RSS (RFC6437 and RFC6438).
Traditionally, devices perform a 5-tuple hash on packets that
includes port numbers. For the most part, these devices can only
compute 5-tuple hashes for TCP and UDP. This severely limits our ability
to get good network load balancing for other protocols (IPIP, GRE,ESP,
etc.), and hence we are limited in using other protocols. Unfortunately,
this method is accepted as the de facto standard to the extent that
there are several proposals to encapsulate protocols in UDP _just_ for
the purposes for getting ECMP to work. With hosts generating flow labels
and devices taking them as input into ECMP (several already do), we can
start to fix this fundamental problem.
This patch set:
- Changes IPV6_FLOWINFO sockopt to be opt-out of flow labels for
connections rather than opt-in
- Disable flow label state ranges sysctl by default
- Enable auto flow labels sysctl by default
v2:
- Added functions to create an skb->hash based on flowi4 and flowi6.
These are called in output path when creating a packet
- Call skb_get_hash_flowi6 in ip6_make_flowlabel
- Implement the auto_flowlabels sysctl as a mode for auto flowlabels.
There are four modes which correspond to flow labels being enabled
and whether socket option can be used to opt in or opt out of
using them
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Initialize auto_flowlabels to one. This enables automatic flow labels,
individual socket may disable them using the IPV6_AUTOFLOWLABEL socket
option.
Signed-off-by: Tom Herbert <tom@herbertland.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Per RFC6437 stateful flow labels (e.g. labels set by flow label manager)
cannot "disturb" nodes taking part in stateless flow labels. While the
ranges only reduce the flow label entropy by one bit, it is conceivable
that this might bias the algorithm on some routers causing a load
imbalance. For best results on the Internet we really need the full
20 bits.
Signed-off-by: Tom Herbert <tom@herbertland.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Change the meaning of net.ipv6.auto_flowlabels to provide a mode for
automatic flow labels generation. There are four modes:
0: flow labels are disabled
1: flow labels are enabled, sockets can opt-out
2: flow labels are allowed, sockets can opt-in
3: flow labels are enabled and enforced, no opt-out for sockets
np->autoflowlabel is initialized according to the sysctl value.
Signed-off-by: Tom Herbert <tom@herbertland.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We can't call skb_get_hash here since the packet is not complete to do
flow_dissector. Create hash based on flowi6 instead.
Signed-off-by: Tom Herbert <tom@herbertland.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add skb_get_hash_flowi6 and skb_get_hash_flowi4 which derive an sk_buff
hash from flowi6 and flowi4 structures respectively. These functions
can be called when creating a packet in the output path where the new
sk_buff does not yet contain a fully formed packet that is parsable by
flow dissector.
Signed-off-by: Tom Herbert <tom@herbertland.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs
Pull btrfs fixes from Chris Mason:
"Filipe fixed up a hard to trigger ENOSPC regression from our merge
window pull, and we have a few other smaller fixes"
* 'for-linus-4.2' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs:
Btrfs: fix quick exhaustion of the system array in the superblock
btrfs: its btrfs_err() instead of btrfs_error()
btrfs: Avoid NULL pointer dereference of free_extent_buffer when read_tree_block() fail
btrfs: Fix lockdep warning of btrfs_run_delayed_iputs()
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"This became a relative big update as it includes the collected ASoC
fixes. There are a few fixes in ASoC core side, mostly for DAPM and
the new topology API. The rest are various ASoC driver-specific
fixes, as well as the usual HD-audio and USB-audio quirks"
* tag 'sound-4.2-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (29 commits)
ALSA: hda - Fix MacBook Pro 5,2 quirk
ALSA: hda - Fix race between PM ops and HDA init/probe
ALSA: usb-audio: add dB range mapping for some devices
ALSA: hda - Apply a fixup to Dell Vostro 5480
ALSA: hda - Add pin quirk for the headset mic jack detection on Dell laptop
ALSA: hda - Apply fixup for another Toshiba Satellite S50D
ALSA: fireworks: add support for AudioFire2 quirk
ALSA: hda - Fix the headset mic that will not work on Dell desktop machine
ALSA: hda - fix cs4210_spdif_automute()
ASoC: pcm1681: Fix setting de-emphasis sampling rate selection
ASoC: ssm4567: Keep TDM_BCLKS in ssm4567_set_dai_fmt
ASoC: sgtl5000: Fix up define for SGTL5000_SMALL_POP
ASoC: dapm: Don't add prefix to widget stream name
ASoC: rt5645: Check if codec is initialized in workqueue handler
ASoC: Intel: Get correct usage_count value to load firmware
ASoC: topology: Fix to add dapm mixer info
ASoC: zx: spdif: Fix devm_ioremap_resource return value check
ASoC: zx: i2s: Fix devm_ioremap_resource return value check
ASoC: mediatek: Use platform_of_node for machine drivers
ASoC: Free card DAPM context on snd_soc_instantiate_card() error path
...
|
|
Florian Fainelli says:
====================
net: GENET, SYSTEMPORT and DSA netconsole
This patch series adds support for netconsole in the GENET, SYSTEMPORT and DSA
drivers.
A small refactoring to the DSA transmit path is required to avoid duplicating
the dsa_netpoll_send_skb() into each and every tagging protocol supported.
Testing on e.g: mv643xx_eth and/or e1000e would be much appreciated!
Changes in v2:
- properly disable/enable interrupts in GENET and SYSTEMPORT
- pass the reallocated SKB back to dsa_slave_xmit() in case a tag protocol had to
alter the original SKB
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add support for using DSA slave network devices with netconsole, which
requires us to allocate and free custom netpoll instances and invoke the
parent network device poll controller callback.
In order for netconsole to work, we need to construct the DSA tag, but
not queue the skb for transmission on the master network device xmit
function.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
All tagging protocols do the same thing: increment device statistics,
make room for the tag to be inserted, create the tag, invoke the parent
network device transmit function.
In order to prepare for adding netpoll support, which requires the tag
creation, but not using the parent network device transmit function, do
some little refactoring which eliminates duplication between the 4
tagging protocols supported.
We need to return a sk_buff pointer back to the caller because the tag
specific transmit function may have to reallocate the original skb (e.g:
tag_trailer.c) and this is the one we should be transmitting, not the
original sk_buff we were passed.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Implement a poll controller for netconsole which invokes the RX
interrupt handler to poll for incoming packets, and cleans up all TX
queues by invoking the TX interrupt handler.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Implement a poll controller for netconsole which invokes both of our
interrupt handlers for the different RX/TX queues.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Commit 50649ab14982 ("stmmac: drop driver from stmmac platform code")
was a bit overzealous in removing code and dropped the MODULE_*
macro's that are still needed since stmmac_platform can be a module.
Fix this by putting the macro's remvoed in 50649ab14982 back.
This fixes the following errors when used as a module:
stmmac_platform: module license 'unspecified' taints kernel.
Disabling lock debugging due to kernel taint
stmmac_platform: Unknown symbol devm_kmalloc (err 0)
stmmac_platform: Unknown symbol stmmac_suspend (err 0)
stmmac_platform: Unknown symbol platform_get_irq_byname (err 0)
stmmac_platform: Unknown symbol stmmac_dvr_remove (err 0)
stmmac_platform: Unknown symbol platform_get_resource (err 0)
stmmac_platform: Unknown symbol of_get_phy_mode (err 0)
stmmac_platform: Unknown symbol of_property_read_u32_array (err 0)
stmmac_platform: Unknown symbol of_alias_get_id (err 0)
stmmac_platform: Unknown symbol stmmac_resume (err 0)
stmmac_platform: Unknown symbol stmmac_dvr_probe (err 0)
Fixes: 50649ab14982 ("stmmac: drop driver from stmmac platform code")
Reported-by: Igor Gnatenko <i.gnatenko.brain@gmail.com>
Signed-off-by: Joachim Eastwood <manabian@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Claudiu Manoil says:
====================
gianfar: wol magic packet fixes
These changes were already validated as part of FSL SDK.
Patch 2 fixes occasional wake-on magic packet failures during
traffic, probably due to incorrect traffic stop/ device halt
sequence and incorrect usage of txlock.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The wol_en flag is 0 by default anyway, and we have the
following inconsistency: a MAGIC packet wol capable eth
interface is registered as a wake-up source but unable
to wake-up the system as wol_en is 0 (wake-on flag set to 'd').
Calling set_wakeup_enable() at netdev open is just redundant
because wol_en is 0 by default.
Let only ethtool call set_wakeup_enable() for now.
The bflock is obviously obsoleted, its utility has been corroded
over time. The bitfield flags used today in gianfar are accessed
only on the init/ config path, with no real possibility of
concurrency - nothing that would justify smth. like bflock.
Signed-off-by: Claudiu Manoil <claudiu.manoil@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
If we disable NAPI in the first place we can mask the device's
interrupts (and halt it) without fearing that imask may be
concurrently accessed from interrupt context, so there's
no need to do local_irq_save() around gfar_halt_nodisable().
lock_rx_qs()/unlock_tx_qs() are just obsoleted and potentially
buggy routines. The txlock is currently used in the driver only
to manage TX congestion, it has nothing to do with halting the
device. With these changes, the TX processing is stopped before
gfar_halt().
Compact gfar_halt() is used instead of gfar_halt_nodisable(),
as it disables Rx/TX DMA h/w blocks and the Rx/TX h/w queues.
gfar_start() re-enables all these blocks on resume. Enabling
the magic-packet mode remains the same, note that the RX block
is re-enabled just before entering sleep mode.
Add IRQF_NO_SUSPEND flag for the error interrupt line, to signal
that the interrupt line must remain active during sleep in order
to wake the system by magic packet (MAG) reception interrupt.
(On some systems the MAG interrupt did trigger w/o this flag
as well, but on others it didn't.)
Without these fixes, when suspended during fair Tx traffic the
interface occasionally failed to be woken up by magic packet.
Signed-off-by: Claudiu Manoil <claudiu.manoil@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
CC drivers/net/ethernet/freescale/gianfar.o
drivers/net/ethernet/freescale/gianfar.c:568:13: warning: 'lock_tx_qs'
defined but not used [-Wunused-function]
static void lock_tx_qs(struct gfar_private *priv)
^
drivers/net/ethernet/freescale/gianfar.c:576:13: warning: 'unlock_tx_qs'
defined but not used [-Wunused-function]
static void unlock_tx_qs(struct gfar_private *priv)
^
Reported-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Claudiu Manoil <claudiu.manoil@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
tlb_dynamic_lb could be set only via sysfs, this patch allows it to be
set via netlink.
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next
Kalle Valo says:
====================
Major changes:
mwifiex:
* add TX DATA Pause support
* add multichannel and TDLS channel switch support
ath10k:
* enable VHT for IBSS
* initial work to support qca99x0 and the corresponding 10.4 firmware branch
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Shradha Shah <sshah@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
function
The policy in the net driver is to attempt MCDI commands and
then handle any EPERM error codes appropriately when returned
by unprivileged functions.
The ethtool selftest contains some tests which are useful on
an unprivileged function, such as the event queue interrupt
tests, but other tests cannot be performed as the function
does not have the required permissions.
If a test returns -EPERM, act as though the test was not run
and continue.
Signed-off-by: Shradha Shah <sshah@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch added driver to support Aquantia PHYs AQ1202, AQ2104, AQR105,
AQR405, which accessed through clause 45.
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Use vsprintf extension %pI4 instead.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The UEFI driver would enable zero length, and the Linux driver doesn't
need it. Zero length let the hw complete the transfer with length 0,
when there is no received packet. It would add the load of USB host
controller and reduce the performance.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Two vxlan driver flags FLOWBASED and COLLECT_METADATA need to be set to
make use of its new flow mode. The former already exposed. Expose the latter.
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com>
Acked-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When we share an action within a filter, the bind refcnt
should increase, therefore we should not call tcf_hash_release().
Fixes: 1a29321ed045 ("net_sched: act: Dont increment refcnt on replace")
Cc: Jamal Hadi Salim <jhs@mojatatu.com>
Cc: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: Cong Wang <cwang@twopensource.com>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Roopa Prabhu says:
====================
af_mpls: fix undefined reference to ip6_route_output with CONFIG_IPV6=n
This patch series uses ipv6_stub_impl.ipv6_dst_lookup instead of
ip6_route_output. Follows the vxlan drivers usage of
ipv6_stub_impl.ipv6_dst_lookup.
There is no sk in the af_mpls context from where
ipv6_stub_impl.ipv6_dst_lookup is used. sk appears to be needed
to get the namespace 'net' and is optional otherwise. This patch series
changes ipv6_stub_impl.ipv6_dst_lookup to take net argument. sk remains
optional.
v1 - v2: use IS_BUILTIN
v2 - v3: Use new Kconfig option that depends on (IPV6 || IPV6=n) as
suggested by Dave. Also uses IS_ERR as suggested by Thomas.
v3 - v4: Include missed case of (MPLS_ROUTING=y && IPV6=m) reported by
Dave.
v4 - v5: Use ipv6_stub_impl.ipv6_dst_lookup as suggested by Hannes
v5 - v6: protect against null ipv6_stub by statically declaring
a ipv6_dst_lookup NOP func
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Undefined reference to ip6_route_output and ip_route_output
was reported with CONFIG_INET=n and CONFIG_IPV6=n.
This patch uses ipv6_stub_impl.ipv6_dst_lookup instead of
ip6_route_output. And wraps affected code under
IS_ENABLED(CONFIG_INET) and IS_ENABLED(CONFIG_IPV6).
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Reported-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch adds net argument to ipv6_stub_impl.ipv6_dst_lookup
for use cases where sk is not available (like mpls).
sk appears to be needed to get the namespace 'net' and is optional
otherwise. This patch series changes ipv6_stub_impl.ipv6_dst_lookup
to take net argument. sk remains optional.
All callers of ipv6_stub_impl.ipv6_dst_lookup have been modified
to pass net. I have modified them to use already available
'net' in the scope of the call. I can change them to
sock_net(sk) to avoid any unintended change in behaviour if sock
namespace is different. They dont seem to be from code inspection.
Signed-off-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Introduce helpers to let eBPF programs attached to TC manipulate tunnel metadata:
bpf_skb_[gs]et_tunnel_key(skb, key, size, flags)
skb: pointer to skb
key: pointer to 'struct bpf_tunnel_key'
size: size of 'struct bpf_tunnel_key'
flags: room for future extensions
First eBPF program that uses these helpers will allocate per_cpu
metadata_dst structures that will be used on TX.
On RX metadata_dst is allocated by tunnel driver.
Typical usage for TX:
struct bpf_tunnel_key tkey;
... populate tkey ...
bpf_skb_set_tunnel_key(skb, &tkey, sizeof(tkey), 0);
bpf_clone_redirect(skb, vxlan_dev_ifindex, 0);
RX:
struct bpf_tunnel_key tkey = {};
bpf_skb_get_tunnel_key(skb, &tkey, sizeof(tkey), 0);
... lookup or redirect based on tkey ...
'struct bpf_tunnel_key' will be extended in the future by adding
elements to the end and the 'size' argument will indicate which fields
are populated, thereby keeping backwards compatibility.
The 'flags' argument may be used as well when the 'size' is not enough or
to indicate completely different layout of bpf_tunnel_key.
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com>
Acked-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Repost patch of driver for LAN7800 family of USB 2.0 & USB 3.0 to Gigabit Ethernet.
- remove module param which can be configurable by standard mechanism.
- remove other module parms except msg_level per review comment.
- update to handle byte swap for statistics structure correctly.
Signed-off-by: Woojung Huh <woojung.huh@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch adds support to read the dmesg BPF JIT dump also from a
file instead of the klog buffer. I found this quite useful when going
through some 'before/after patch' logs. It also fixes a regex leak
found by valgrind when no image dump was found.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu
Pull IOMMU fixes from Joerg Roedel:
"These fixes are all for the AMD IOMMU driver:
- A regression with HSA caused by the conversion of the driver to
default domains. The fixes make sure that an HSA device can still
be attached to an IOMMUv2 domain and that these domains also allow
non-IOMMUv2 capable devices.
- Fix iommu=pt mode which did not work because the dma_ops where set
to nommu_ops, which breaks devices that can only do 32bit DMA.
- Fix an issue with non-PCI devices not working, because there are no
dma_ops for them. This issue was discovered recently as new AMD
x86 platforms have non-PCI devices too"
* tag 'iommu-fixes-v4.2-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu:
iommu/amd: Allow non-ATS devices in IOMMUv2 domains
iommu/amd: Set global dma_ops if swiotlb is disabled
iommu/amd: Use swiotlb in passthrough mode
iommu/amd: Allow non-IOMMUv2 devices in IOMMUv2 domains
iommu/amd: Use iommu core for passthrough mode
iommu/amd: Use iommu_attach_group()
|
|
git://anongit.freedesktop.org/drm-intel
Pull drm intel fixes from Daniel Vetter:
"I delayed my -fixes pull a bit hoping that I could include a fix for
the dp mst stuff but looks a bit more nasty than that. So just 3
other regression fixes, one 4.2 other two cc: stable"
* tag 'drm-intel-fixes-2015-07-31' of git://anongit.freedesktop.org/drm-intel:
drm/i915: Declare the swizzling unknown for L-shaped configurations
drm/i915: Mark PIN_USER binding as GLOBAL_BIND without the aliasing ppgtt
drm/i915: Replace WARN inside I915_READ64_2x32 with retry loop
|
|
Pull drm fixes from Dave Airlie:
"This has a bunch of nouveau fixes, as Ben has been hibernating and has
lots of small fixes for lots of bugs across nouveau.
Radeon has one major fix for hdmi/dp audio regression that is larger
than Alex would like, but seems to fix up a fair few bugs, along with
some misc fixes.
And a few msm fixes, one of which is also a bit large.
But nothing in here seems insane or crazy for this stage, just more
than I'd like"
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux: (33 commits)
drm/msm/mdp5: release SMB (shared memory blocks) in various cases
drm/msm: change to uninterruptible wait in atomic commit
drm/msm: mdp4: Fix drm_framebuffer dereference crash
drm/msm: fix msm_gem_prime_get_sg_table()
drm/amdgpu: add new parameter to seperate map and unmap
drm/amdgpu: hdp_flush is not needed for inside IB
drm/amdgpu: different emit_ib for gfx and compute
drm/amdgpu: information leak in amdgpu_info_ioctl()
drm/amdgpu: clean up init sequence for failures
drm/radeon/combios: add some validation of lvds values
drm/radeon: rework audio modeset to handle non-audio hdmi features
drm/radeon: rework audio detect (v4)
drm/amdgpu: Drop drm/ prefix for including drm.h in amdgpu_drm.h
drm/radeon: Drop drm/ prefix for including drm.h in radeon_drm.h
drm/nouveau/nouveau/ttm: fix tiled system memory with Maxwell
drm/nouveau/kms/nv50-: guard against enabling cursor on disabled heads
drm/nouveau/fbcon/g80: reduce PUSH_SPACE alloc, fire ring on accel init
drm/nouveau/fbcon/gf100-: reduce RING_SPACE allocation
drm/nouveau/fbcon/nv11-: correctly account for ring space usage
drm/nouveau/bios: add proper support for opcode 0x59
...
|
|
With the grouping of multi-function devices a non-ATS
capable device might also end up in the same domain as an
IOMMUv2 capable device.
So handle this situation gracefully and don't consider it a
bug anymore.
Tested-by: Oded Gabbay <oded.gabbay@gmail.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
|
|
This reverts commit 6301566e0b2dafa7d6779598621bca867962a0a2. Oleksij Rempel
noticed that the randomness doesn't look to be good enough and Stephan Mueller
commented:
"I would say that the discussed RNG does not seem fit for hooking it up with the
hwrandom framework."
http://lkml.kernel.org/g/3945775.m5HblJPgiO@tauon.atsec.com
So let's the revert the patch until we are sure that we can trust this random
generator.
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/dgc/linux-xfs
Pull xfs fixes from Dave Chinner:
"There are a couple of recently found, long standing remote attribute
corruption fixes caused by log recovery getting confused after a
crash, and the new DAX code in XFS (merged in 4.2-rc1) needs to
actually use the DAX fault path on read faults.
Summary:
- remote attribute log recovery corruption fixes
- DAX page faults need to use direct mappings, not a page cache
mapping"
* tag 'xfs-for-linus-4.2-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/dgc/linux-xfs:
xfs: remote attributes need to be considered data
xfs: remote attribute headers contain an invalid LSN
xfs: call dax_fault on read page faults for DAX
|
|
Jon Maloy says:
====================
tipc: separate link aggregation from link layer
We continue the work on separating the roles of the link aggregation and
link layers, as well as making code cleanups in general.
This second commit batch focuses on moving the orchestration of link
failover and synchronization to the node level, as well as preparing the
node lock structure for further future impovements. We also make some
changes to message delivery between link and socket layer, in order to
make this mechanism safer and less obscure.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We simplify the link creation function tipc_link_create() and the way
the link struct it is connected to the node struct. In particular, we
remove the duplicate initialization of some fields which are anyway set
in tipc_link_reset().
Tested-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Currently, when we extract small messages from a message bundle, or
when many messages have accumulated in the link arrival queue, those
messages are added one by one to the lock protected link input queue.
This may increase contention with the reader of that queue, in
the function tipc_sk_rcv().
This commit introduces a temporary, unprotected input queue in
tipc_link_rcv() for such cases. Only when the arrival queue has been
emptied, and the function is ready to return, does it splice the whole
temporary queue into the real input queue.
Tested-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
After the most recent changes, all access calls to a link which
may entail addition of messages to the link's input queue are
postpended by an explicit call to tipc_sk_rcv(), using a reference
to the correct queue.
This means that the potentially hazardous implicit delivery, using
tipc_node_unlock() in combination with a binary flag and a cached
queue pointer, now has become redundant.
This commit removes this implicit delivery mechanism both for regular
data messages and for binding table update messages.
Tested-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In order to facilitate future improvements to the locking structure, we
want to make resetting and establishing of links non-atomic. I.e., the
functions tipc_node_link_up() and tipc_node_link_down() should be called
from outside the node lock context, and grab/release the node lock
themselves. This requires that we can freeze the link state from the
moment it is set to RESETTING or PEER_RESET in one lock context until
it is set to RESET or ESTABLISHING in a later context. The recently
introduced link FSM makes this possible, so we are now ready to introduce
the above change.
This commit implements this.
Tested-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
