summaryrefslogtreecommitdiff
AgeCommit message (Collapse)Author
2011-09-14b43: N-PHY: replace some hacks with nice tables opsRafał Miłecki
Signed-off-by: Rafał Miłecki <zajec5@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-09-14b43: N-PHY: use helper for checking IPARafał Miłecki
Signed-off-by: Rafał Miłecki <zajec5@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-09-14mac80211: add ssid config to bss information in AP-modeArik Nemtsov
Set SSID information from nl80211 beacon parameters. Advertise changes in SSID to low level drivers. Signed-off-by: Arik Nemtsov <arik@wizery.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-09-14b43: LCN-PHY: load TX gain table on initRafał Miłecki
Signed-off-by: Rafał Miłecki <zajec5@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-09-14b43: add my copyrights and myself as the module authorRafał Miłecki
Signed-off-by: Rafał Miłecki <zajec5@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-09-14b43: drop Copyright for not really copyrightable infoRafał Miłecki
As discussed in "Licensing wlc_phy_radio.h and brcm80211" (Message-ID: <AANLkTinQMRGkOvi4e4JMsHGV_BF_4Rf5oHCtZgQjwQ1g@mail.gmail.com>) content of that file is not copyrightable, just names and numbers. Signed-off-by: Rafał Miłecki <zajec5@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-09-14minstrel_ht: fix Open BA session request floodsChristian Lamparter
Minstrel HT tries very hard to establish a BA session with each peer once there's some data on the way. However the stack does not inform minstrel if an aggregation session is already in place, so it keeps trying and wastes good cycles in the tx status path. [ 8149.946393] Open BA session requested for $AP tid 0 [ 8150.048765] Open BA session requested for $AP tid 0 [ 8150.174509] Open BA session requested for $AP tid 0 [ 8150.274376] Open BA session requested for $AP tid 0 ... Signed-off-by: Christian Lamparter <chunkeey@googlemail.com> Acked-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-09-14ath9k: implement .get_antenna and .set_antennaFelix Fietkau
On MIMO chips this can be used to enable/disable hardware chains, ensuring that the MCS information is updated accordingly. On non-MIMO chips with rx diversity (e.g. 9285), this configures the rx input antenna. Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-09-14ath9k: merge reset related functionsFelix Fietkau
reduces unnecessary code duplication. Also takes the sc_pcu_lock within ath_reset instead of callsites, which makes it possible to always cancel all queued work items before the reset, possibly fixing a few race conditions (work items vs reset) along with it. Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-09-14ath9k: always call ath_reset from workqueue contextFelix Fietkau
This makes it much easier to add further rework to avoid race conditions between reset and other work items. Move other functions to make ath_reset static. Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-09-14ath9k: move a few functions aroundFelix Fietkau
Helps with making ath_reset static in the next commit Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-09-14ath9k: eliminate common->{rx,tx}_chainmaskFelix Fietkau
we already have ah->{rx,tx}chainmask for the same purpose Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-09-14mac80211: stop tx before doing hw config and rate updateRajkumar Manoharan
The assumption is that during the hw config, transmission was already stopped by mac80211. Sometimes the AP can be switching b/w the ht modes due to intolerant or etc where STA is in the middle of transmission. In such scenario, buffer overflow was observed at driver side. And also before updating the rate control, the frames are continued to xmited with older rates. This patch ensures that the frames are always xmitted with updated rates and avoid buffer overflow. Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com> Reviewed-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-09-14b43: N-PHY: implement enabling TX power controlRafał Miłecki
Signed-off-by: Rafał Miłecki <zajec5@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-09-14mac80211: Stop forwarding mesh traffic when tx queues are fullJavier Cardona
Tx flow control for non-mesh modes of operation only needs to act on the net device queues: when the hardware queues are full we stop accepting traffic from the net device. In mesh, however, we also need to stop forwarding traffic. This patch checks the hardware queues before attempting to forward a mesh frame. Signed-off-by: Javier Cardona <javier@cozybit.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-09-14mac80211: check if mesh frame is in RMC after decryptThomas Pedersen
To check whether a frame is in the RMC, we need access to the mesh header. This header is encrypted in encrypted data frames, so make this check after the frame has been decrypted. Signed-off-by: Thomas Pedersen <thomas@cozybit.com> Signed-off-by: Javier Cardona <javier@cozybit.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-09-14mac80211: make ieee80211_send_bar available for driversFelix Fietkau
To properly maintain the peer's block ack window, the driver needs to be able to control the new starting sequence number that is sent along with the BlockAckReq frame. Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-09-14cfg80211: reorder code to obsolete forward declarationSven Neumann
Reorder functions to remove the need for a forward declaration introduced by the last commit. Signed-off-by: Sven Neumann <s.neumann@raumfeld.com> Cc: John W. Linville <linville@tuxdriver.com> Cc: Luis R. Rodriguez <mcgrof@gmail.com> Cc: Daniel Mack <daniel@zonque.org> Cc: linux-wireless@vger.kernel.org Acked-by: Luis R. Rodriguez <mcgrof@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-09-14cfg80211: hold reg_mutex when updating regulatorySven Neumann
The function wiphy_update_regulatory() uses the static variable last_request and thus needs to be called with reg_mutex held. This is the case for all users in reg.c, but the function was exported for use by wiphy_register(), from where it is called without the lock being held. Fix this by making wiphy_update_regulatory() private and introducing regulatory_update() as a wrapper that acquires and holds the lock. Signed-off-by: Sven Neumann <s.neumann@raumfeld.com> Cc: John W. Linville <linville@tuxdriver.com> Cc: Luis R. Rodriguez <mcgrof@gmail.com> Cc: Daniel Mack <daniel@zonque.org> Cc: linux-wireless@vger.kernel.org Acked-by: Luis R. Rodriguez <mcgrof@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-09-13cfg80211: print bandwidth in chan_reg_rule_print_dbg()Pavel Roskin
Two spaces and the second "KHz" suggest that the code author meant to print the bandwidth but forgot it. The code appears in commit e702d3cf already with two spaces and "KHz" in place of the bandwidth. Signed-off-by: Pavel Roskin <proski@gnu.org> Acked-by: Luis R. Rodriguez <mcgrof@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-09-13ath9k: ath9k_hw_set_txpowerlimit sets previous txpowerBill Jordan
In commit 9c204b46c7af93e334114bea1f5eeaa6fea9ba07 (ath9k_hw: do not limit initial tx power to 20 dbm), setting of txpower was broken. This patch fixes it by initializing reg_pwr from the new power limit, not the previous value. Signed-off-by: Bill Jordan <bjordan@rajant.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-09-13b43: LCN-PHY: add conditions for few operationsRafał Miłecki
It was not possible to guess the conditions from MMIO dumps. Take them from brcmsmac code. Signed-off-by: Rafał Miłecki <zajec5@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-09-13b43: LCN-PHY: rename functions, get rid of magic namesRafał Miłecki
We've compared b43 with brcmsmac and took functions names from the later. Signed-off-by: Rafał Miłecki <zajec5@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-09-13b43: LCN-PHY: upload additional 0x7 tableRafał Miłecki
Signed-off-by: Rafał Miłecki <zajec5@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-09-13b43: LCN-PHY: rewrite 0x7 table at the end of initRafał Miłecki
This is not implemented in brcmsmac, but was noticed in (newer) wl. Can be workaround for some hardware bug. Signed-off-by: Rafał Miłecki <zajec5@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-09-13b43: LCN-PHY: put tables functions in correct fileRafał Miłecki
Signed-off-by: Rafał Miłecki <zajec5@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-09-13b43: LCN-PHY: minor fixesRafał Miłecki
The biggest change is reversing order of reading 32-bit table value. MMIO dumps has shown it's done that way for LCN-PHY. Signed-off-by: Rafał Miłecki <zajec5@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-09-13rt2x00: Add new chipset supportzero.lin
Signed-off-by: zero.lin <zero.lin@ralinktech.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-09-13nl80211/cfg80211: add match filtering for sched_scanLuciano Coelho
Introduce filtering for scheduled scans to reduce the number of unnecessary results (which cause useless wake-ups). Add a new nested attribute where sets of parameters to be matched can be passed when starting a scheduled scan. Only scan results that match any of the sets will be returned. At this point, the set consists of a single parameter, an SSID. This can be easily extended in the future to support more complex matches. Signed-off-by: Luciano Coelho <coelho@ti.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-09-13nl80211/cfg80211: add WIPHY_FLAG_AP_UAPSD flagEliad Peller
add WIPHY_FLAG_AP_UAPSD flag to indicate uapsd support on AP mode. Advertise it to userspace by including a new NL80211_ATTR_SUPPORT_AP_UAPSD attribute. Signed-off-by: Eliad Peller <eliad@wizery.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-09-13iwlwifi: signedness bug in iwl_trans_pcie_tx_agg_alloc()Dan Carpenter
unsigned shorts and unsigned chars are never == -1. Signed-off-by: Dan Carpenter <error27@gmail.com> Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-09-13iwlwifi: fix double assign in iwl_start_tx_ba_trans_ready()Dan Carpenter
"vif" is assigned twice. We can remove the first one. This silences a Smatch warning that "ctx" could be one step past the end of the priv->contexts[] array. Signed-off-by: Dan Carpenter <error27@gmail.com> Reviewed-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-09-13ath9k_hw: Fix rx latency of 11a modeRajkumar Manoharan
Rx latecy to start signal(usec) of 11a is 41 not 37 and also corrected the rx delay in quarter rate. Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-09-13mac80211: handle allocation failures in mesh_pathtbl_init()Dan Carpenter
The calls to kzalloc() weren't checked here and it upsets the static checkers. Obviously they're not super likely to fail, but we might as well add some error handling. Signed-off-by: Dan Carpenter <error27@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-09-13mac80211: add flag to indicate HW only Tx-agg setup supportArik Nemtsov
When this flag is set, Tx A-MPDU sessions will not be started by mac80211. This flag is required for devices that support Tx A-MPDU setup in hardware. Signed-off-by: Arik Nemtsov <arik@wizery.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-09-13wireless: Remove unnecessary OOM logging messagesJoe Perches
Removing unnecessary messages saves code and text. Site specific OOM messages are duplications of a generic MM out of memory message and aren't really useful, so just delete them. Signed-off-by: Joe Perches <joe@perches.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-09-13rfkill: Remove unnecessary OOM logging messagesJoe Perches
Removing unnecessary messages saves code and text. Site specific OOM messages are duplications of a generic MM out of memory message and aren't really useful, so just delete them. Signed-off-by: Joe Perches <joe@perches.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-09-13mac80211: Remove unnecessary OOM logging messagesJoe Perches
Removing unnecessary messages saves code and text. Site specific OOM messages are duplications of a generic MM out of memory message and aren't really useful, so just delete them. Signed-off-by: Joe Perches <joe@perches.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-09-13mac80211: Consolidate mesh path duplicated functionsJavier Cardona
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-09-13mac80211: Consolidate {mesh,mpp}_path_flush into one functionJavier Cardona
Signed-off-by: Javier Cardona <javier@cozybit.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-09-13mac80211: Don't iterate twice over all mpaths when once in sufficientJavier Cardona
Signed-off-by: Javier Cardona <javier@cozybit.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-09-13mac80211: Remove redundant mesh path expiration checksJavier Cardona
Signed-off-by: Javier Cardona <javier@cozybit.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-09-13mac80211: Improve mpath state lockingJavier Cardona
No need to take the mpath state lock when an mpath is removed. Also, no need checking the lock when reading mpath flags. Signed-off-by: Javier Cardona <javier@cozybit.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-09-13mac80211: Remove mesh paths when an interface is removedJavier Cardona
When an interface is removed, the mesh paths associated with it should also be removed. This fixes a bug we observed when reloading a device driver module without reloading mac80211s. Signed-off-by: Javier Cardona <javier@cozybit.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-09-13mac80211: Fix RCU pointer dereference in mesh_path_discard_frame()Javier Cardona
Reported by Pedro Larbig (ASPj) Signed-off-by: Javier Cardona <javier@cozybit.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-09-13mwifiex: replace kmalloc & memcpy sequence with kmemdupYogesh Ashok Powar
Sequence of kmalloc/kzalloc and memcpy is replaced with kmemdup. Cc: Walter Harms <wharms@bfs.de> Signed-off-by: Yogesh Ashok Powar <yogeshp@marvell.com> Signed-off-by: Kiran Divekar <dkiran@marvell.com> Signed-off-by: Bing Zhao <bzhao@marvell.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-09-13ath9k: fix checks for first subframe delimiter paddingFelix Fietkau
The commit "ath9k_hw: Fix exceed transmission burst-time of 5GHz" added a padding of 60 delimiters on the first subframe to work around an issue on AR9380, but it lacked the checks to prevent it from being applied to pre-AR9380, enterprise AR9380 or AR9580+ Signed-off-by: Felix Fietkau <nbd@openwrt.org> Cc: Rajkumar Manoharan <rmanohar@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-09-13mwl8k: Set hardware flag IEEE80211_HW_AP_LINK_PSYogesh Ashok Powar
This will avoid mac80211 to trigger PS mode for connected station based on the PM bit of incoming frames. AP firmware is capable of handling such frames and buffering TX frames destined to the stations that are in PS mode. Signed-off-by: Yogesh Ashok Powar <yogeshp@marvell.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-09-13ath9k_hw: fix the last register write for ar5416 addacFelix Fietkau
The previous register used in these initvals was probably accidentally copied over from the AR9100 values. Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-09-13ath9k_hw: drop an unused column in AR5008-AR9002 initvalsFelix Fietkau
It was used for the defunct 'turbo' mode which was never implemented in the driver. Saves ~7.5k uncompressed Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
generated by cgit v0.10.2 at 2024-09-20 21:38:29 (GMT)