| Age | Commit message (Collapse) | Author |
|---|
|
This is a simple ping pong driver that exercises the scratch pads and
doorbells of the ntb hardware. This driver may be used to test that
your ntb hardware and drivers are functioning at a basic level.
Signed-off-by: Allen Hubbe <Allen.Hubbe@emc.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
|
|
Add module parameters for the addresses to be used in B2B topology.
Signed-off-by: Allen Hubbe <Allen.Hubbe@emc.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
|
|
Reset the link stats when the link goes down. In particular, the TX and
RX index and count must be reset, or else the TX side will be sending
packets to the RX side where the RX side is not expecting them. Reset
all the stats, to be consistent.
Signed-off-by: Allen Hubbe <Allen.Hubbe@emc.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
|
|
On link down, don't advance RX index to the next entry. The next entry
should never be valid after receiving the link down flag.
Signed-off-by: Allen Hubbe <Allen.Hubbe@emc.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
|
|
The same message "qp %d: Link Down\n" was printed at two locations in
ntb_transport. Change the messages so they are distinct.
Signed-off-by: Allen Hubbe <Allen.Hubbe@emc.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
|
|
Set errata flags for the specific device IDs to which they apply,
instead of the whole Xeon hardware class.
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
|
|
Link training should be enabled in the driver probe for root port mode.
We should not have to wait for transport to be loaded for this to
happen. Otherwise the ntb device will not show up on the transparent
bridge side of the link.
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
|
|
The transport was writing and then reading the peer scratch pad,
essentially reading what it just wrote instead of exchanging any
information with the peer. The transport expects the peer values to be
the same as the local values, so this issue was not obvious.
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
|
|
Change ntb_hw_intel to use the new NTB hardware abstraction layer.
Split ntb_transport into its own driver. Change it to use the new NTB
hardware abstraction layer.
Signed-off-by: Allen Hubbe <Allen.Hubbe@emc.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
|
|
Abstract the NTB device behind a programming interface, so that it can
support different hardware and client drivers.
Signed-off-by: Allen Hubbe <Allen.Hubbe@emc.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull irq update from Thomas Gleixner:
"The last update for 4.2 is just moving a macro from a local header to
the global one, so it can be used in architecture code as well.
Cleanup of the now empty local header is 4.3 material"
* 'irq-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
irqchip: Move IRQCHIP_DECLARE macro to include/linux/irqchip.h
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 fixes from Ingo Molnar:
"Two FPU rewrite related fixes. This addresses all known x86
regressions at this stage. Also some other misc fixes"
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/fpu: Fix boot crash in the early FPU code
x86/asm/entry/64: Update path names
x86/fpu: Fix FPU related boot regression when CPUID masking BIOS feature is enabled
x86/boot/setup: Clean up the e820_reserve_setup_data() code
x86/kaslr: Fix typo in the KASLR_FLAG documentation
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull scheduler fixes from Ingo Molnar:
"Debug info and other statistics fixes and related enhancements"
* 'sched-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
sched/numa: Fix numa balancing stats in /proc/pid/sched
sched/numa: Show numa_group ID in /proc/sched_debug task listings
sched/debug: Move print_cfs_rq() declaration to kernel/sched/sched.h
sched/stat: Expose /proc/pid/schedstat if CONFIG_SCHED_INFO=y
sched/stat: Simplify the sched_info accounting dependency
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull perf updates from Ingo Molnar:
"This tree includes an x86 PMU scheduling fix, but most changes are
late breaking tooling fixes and updates:
User visible fixes:
- Create config.detected into OUTPUT directory, fixing parallel
builds sharing the same source directory (Aaro Kiskinen)
- Allow to specify custom linker command, fixing some MIPS64 builds.
(Aaro Kiskinen)
- Fix to show proper convergence stats in 'perf bench numa' (Srikar
Dronamraju)
User visible changes:
- Validate syscall list passed via -e argument to 'perf trace'.
(Arnaldo Carvalho de Melo)
- Introduce 'perf stat --per-thread' (Jiri Olsa)
- Check access permission for --kallsyms and --vmlinux (Li Zhang)
- Move toggling event logic from 'perf top' and into hists browser,
allowing freeze/unfreeze with event lists with more than one entry
(Namhyung Kim)
- Add missing newlines when dumping PERF_RECORD_FINISHED_ROUND and
showing the Aggregated stats in 'perf report -D' (Adrian Hunter)
Infrastructure fixes:
- Add missing break for PERF_RECORD_ITRACE_START, which caused those
events samples to be parsed as well as PERF_RECORD_LOST_SAMPLES.
ITRACE_START only appears when Intel PT or BTS are present, so..
(Jiri Olsa)
- Call the perf_session destructor when bailing out in the inject,
kmem, report, kvm and mem tools (Taeung Song)
Infrastructure changes:
- Move stuff out of 'perf stat' and into the lib for further use
(Jiri Olsa)
- Reference count the cpu_map and thread_map classes (Jiri Olsa)
- Set evsel->{cpus,threads} from the evlist, if not set, allowing the
generalization of some 'perf stat' functions that previously were
accessing private static evlist variable (Jiri Olsa)
- Delete an unnecessary check before the calling free_event_desc()
(Markus Elfring)
- Allow auxtrace data alignment (Adrian Hunter)
- Allow events with dot (Andi Kleen)
- Fix failure to 'perf probe' events on arm (He Kuang)
- Add testing for Makefile.perf (Jiri Olsa)
- Add test for make install with prefix (Jiri Olsa)
- Fix single target build dependency check (Jiri Olsa)
- Access thread_map entries via accessors, prep patch to hold more
info per entry, for ongoing 'perf stat --per-thread' work (Jiri
Olsa)
- Use __weak definition from compiler.h (Sukadev Bhattiprolu)
- Split perf_pmu__new_alias() (Sukadev Bhattiprolu)"
* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (54 commits)
perf tools: Allow to specify custom linker command
perf tools: Create config.detected into OUTPUT directory
perf mem: Fill in the missing session freeing after an error occurs
perf kvm: Fill in the missing session freeing after an error occurs
perf report: Fill in the missing session freeing after an error occurs
perf kmem: Fill in the missing session freeing after an error occurs
perf inject: Fill in the missing session freeing after an error occurs
perf tools: Add missing break for PERF_RECORD_ITRACE_START
perf/x86: Fix 'active_events' imbalance
perf symbols: Check access permission when reading symbol files
perf stat: Introduce --per-thread option
perf stat: Introduce print_counters function
perf stat: Using init_stats instead of memset
perf stat: Rename print_interval to process_interval
perf stat: Remove perf_evsel__read_cb function
perf stat: Move perf_stat initialization counter process code
perf stat: Move zero_per_pkg into counter process code
perf stat: Separate counters reading and processing
perf stat: Introduce read_counters function
perf stat: Introduce perf_evsel__read function
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull max log buf size increase from Ingo Molnar:
"Ran into this limit recently, so increase it by an order of magnitude"
* 'core-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
printk: Increase maximum CONFIG_LOG_BUF_SHIFT from 21 to 25
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input
Pull second round of input updates from Dmitry Torokhov:
"A new driver for Weida wdt87xx touch controllers, and a bunch of
fixups for other drivers"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: wdt87xx_i2c - add a scaling factor for TOUCH_MAJOR event
Input: wdt87xx_i2c - remove stray newline in diagnostic message
Input: arc_ps2 - add HAS_IOMEM dependency
Input: wdt87xx_i2c - fix format warning
Input: improve parsing OF parameters for touchscreens
Input: edt-ft5x06 - mark as direct input device
Input: use for_each_set_bit() where appropriate
Input: add a driver for wdt87xx touchscreen controller
Input: axp20x-pek - fix reporting button state as inverted
Input: xpad - re-send LED command on present event
Input: xpad - set the LEDs properly on XBox Wireless controllers
Input: imx_keypad - check for clk_prepare_enable() error
|
|
Jan Kara and Thomas Gleixner reported boot crashes in the FPU
code:
general protection fault: 0000 [#1] SMP
RIP: 0010:[<ffffffff81048a6c>] [<ffffffff81048a6c>] mxcsr_feature_mask_init+0x1c/0x40
2b:* 0f ae 85 00 fe ff ff fxsave -0x200(%rbp)
and bisected it down to the following FPU commit:
91a8c2a5b43f ("x86/fpu: Clean up and fix MXCSR handling")
The reason is that the on-stack FPU registers state variable,
used by the FXSAVE instruction, did not have the required
minimum alignment of 16 bytes, causing the general protection
fault.
This is most likely a GCC bug in older GCC versions, but the
offending commit also added a bogus extra 32-byte alignment
(which GCC ignored too).
So fix this bug by making the variable static again, but also
mark it __initdata this time, because fpu__init_system_mxcsr()
is now an __init function.
Reported-and-bisected-by: Jan Kara <jack@suse.cz>
Reported-bisected-and-tested-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: Dave Hansen <dave.hansen@linux.intel.com>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Jan Kara <jack@suse.cz>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Quentin Casasnovas <quentin.casasnovas@oracle.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/20150704075819.GA9201@gmail.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
Commit 44dba3d5d6a1 ("sched: Refactor task_struct to use
numa_faults instead of numa_* pointers") modified the way
tsk->numa_faults stats are accounted.
However that commit never touched show_numa_stats() that is displayed
in /proc/pid/sched and thus the numbers displayed in /proc/pid/sched
don't match the actual numbers.
Fix it by making sure that /proc/pid/sched reflects the task
fault numbers. Also add group fault stats too.
Also couple of more modifications are added here:
1. Format changes:
- Previously we would list two entries per node, one for private
and one for shared. Also the home node info was listed in each entry.
- Now preferred node, total_faults and current node are
displayed separately.
- Now there is one entry per node, that lists private,shared task and
group faults.
2. Unit changes:
- p->numa_pages_migrated was getting reset after every read of
/proc/pid/sched. It's more useful to have absolute numbers since
differential migrations between two accesses can be more easily
calculated.
Signed-off-by: Srikar Dronamraju <srikar@linux.vnet.ibm.com>
Acked-by: Rik van Riel <riel@redhat.com>
Cc: Iulia Manda <iulia.manda21@gmail.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Mel Gorman <mgorman@suse.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/1435252903-1081-4-git-send-email-srikar@linux.vnet.ibm.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
Having the numa group ID in /proc/sched_debug helps to see how
the numa groups have spread across the system.
Signed-off-by: Srikar Dronamraju <srikar@linux.vnet.ibm.com>
Acked-by: Rik van Riel <riel@redhat.com>
Cc: Iulia Manda <iulia.manda21@gmail.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Mel Gorman <mgorman@suse.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/1435252903-1081-3-git-send-email-srikar@linux.vnet.ibm.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
Currently print_cfs_rq() is declared in include/linux/sched.h.
However it's not used outside kernel/sched. Hence move the
declaration to kernel/sched/sched.h
Also some functions are only available for CONFIG_SCHED_DEBUG=y.
Hence move the declarations to within the #ifdef.
Signed-off-by: Srikar Dronamraju <srikar@linux.vnet.ibm.com>
Acked-by: Rik van Riel <riel@redhat.com>
Cc: Iulia Manda <iulia.manda21@gmail.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Mel Gorman <mgorman@suse.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/1435252903-1081-2-git-send-email-srikar@linux.vnet.ibm.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
Expand /proc/pid/schedstat output:
- enable it on CONFIG_TASK_DELAY_ACCT=y && !CONFIG_SCHEDSTATS kernels.
- dump all zeroes on kernels that are booted with the 'nodelayacct'
option, which boot option disables delay accounting on
CONFIG_TASK_DELAY_ACCT=y kernels.
Signed-off-by: Naveen N. Rao <naveen.n.rao@linux.vnet.ibm.com>
Cc: Balbir Singh <bsingharora@gmail.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Srikar Dronamraju <srikar@linux.vnet.ibm.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: a.p.zijlstra@chello.nl
Cc: ricklind@us.ibm.com
Link: http://lkml.kernel.org/r/5ccbef17d4bc841084ea6e6421d4e4a23b7b806f.1435654789.git.naveen.n.rao@linux.vnet.ibm.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
Both CONFIG_SCHEDSTATS=y and CONFIG_TASK_DELAY_ACCT=y track task
sched_info, which results in ugly #if clauses.
Simplify the code by introducing a synthethic CONFIG_SCHED_INFO
switch, selected by both.
Signed-off-by: Naveen N. Rao <naveen.n.rao@linux.vnet.ibm.com>
Cc: Balbir Singh <bsingharora@gmail.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Srikar Dronamraju <srikar@linux.vnet.ibm.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: a.p.zijlstra@chello.nl
Cc: ricklind@us.ibm.com
Link: http://lkml.kernel.org/r/8d19eef800811a94b0f91bcbeb27430a884d7433.1435255405.git.naveen.n.rao@linux.vnet.ibm.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
Prepare second round of input updates for 4.2 merge window.
|
|
git://anongit.freedesktop.org/drm-intel
Pull drm EDID fix from Daniel Vetter:
"Since Dave is enjoying vacation I figured I'll send you this drm core
fix directly"
* tag 'topic/drm-fixes-2015-07-04' of git://anongit.freedesktop.org/drm-intel:
drm/crtc: Fix edid length computation
|
|
Pull virtio/vhost cross endian support from Michael Tsirkin:
"I have just queued some more bugfix patches today but none fix
regressions and none are related to these ones, so it looks like a
good time for a merge for -rc1.
The motivation for this is support for legacy BE guests on the new LE
hosts. There are two redeeming properties that made me merge this:
- It's a trivial amount of code: since we wrap host/guest accesses
anyway, almost all of it is well hidden from drivers.
- Sane platforms would never set flags like VHOST_CROSS_ENDIAN_LEGACY,
and when it's clear, there's zero overhead (as some point it was
tested by compiling with and without the patches, got the same
stripped binary).
Maybe we could create a Kconfig symbol to enforce the second point:
prevent people from enabling it eg on x86. I will look into this"
* tag 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost:
virtio-pci: alloc only resources actually used.
macvtap/tun: cross-endian support for little-endian hosts
vhost: cross-endian support for legacy devices
virtio: add explicit big-endian support to memory accessors
vhost: introduce vhost_is_little_endian() helper
vringh: introduce vringh_is_little_endian() helper
macvtap: introduce macvtap_is_little_endian() helper
tun: add tun_is_little_endian() helper
virtio: introduce virtio_is_little_endian() helper
|
|
The length of each EDID block is EDID_LENGTH, and number of blocks is
(1 + edid->extensions) - we need to multiply not add them.
This causes wrong EDID to be passed on, and is a regression introduced
by d2ed34362a52 (drm: Introduce helper for replacing blob properties)
Signed-off-by: Shixin Zeng <zeng.shixin@gmail.com>
Cc: Daniel Stone <daniels@collabora.com>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Daniel Stone <daniels@collabora.com>
[danvet: Add Cc: and fix commit summary.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/ebiederm/user-namespace
Pull user namespace updates from Eric Biederman:
"Long ago and far away when user namespaces where young it was realized
that allowing fresh mounts of proc and sysfs with only user namespace
permissions could violate the basic rule that only root gets to decide
if proc or sysfs should be mounted at all.
Some hacks were put in place to reduce the worst of the damage could
be done, and the common sense rule was adopted that fresh mounts of
proc and sysfs should allow no more than bind mounts of proc and
sysfs. Unfortunately that rule has not been fully enforced.
There are two kinds of gaps in that enforcement. Only filesystems
mounted on empty directories of proc and sysfs should be ignored but
the test for empty directories was insufficient. So in my tree
directories on proc, sysctl and sysfs that will always be empty are
created specially. Every other technique is imperfect as an ordinary
directory can have entries added even after a readdir returns and
shows that the directory is empty. Special creation of directories
for mount points makes the code in the kernel a smidge clearer about
it's purpose. I asked container developers from the various container
projects to help test this and no holes were found in the set of mount
points on proc and sysfs that are created specially.
This set of changes also starts enforcing the mount flags of fresh
mounts of proc and sysfs are consistent with the existing mount of
proc and sysfs. I expected this to be the boring part of the work but
unfortunately unprivileged userspace winds up mounting fresh copies of
proc and sysfs with noexec and nosuid clear when root set those flags
on the previous mount of proc and sysfs. So for now only the atime,
read-only and nodev attributes which userspace happens to keep
consistent are enforced. Dealing with the noexec and nosuid
attributes remains for another time.
This set of changes also addresses an issue with how open file
descriptors from /proc/<pid>/ns/* are displayed. Recently readlink of
/proc/<pid>/fd has been triggering a WARN_ON that has not been
meaningful since it was added (as all of the code in the kernel was
converted) and is not now actively wrong.
There is also a short list of issues that have not been fixed yet that
I will mention briefly.
It is possible to rename a directory from below to above a bind mount.
At which point any directory pointers below the renamed directory can
be walked up to the root directory of the filesystem. With user
namespaces enabled a bind mount of the bind mount can be created
allowing the user to pick a directory whose children they can rename
to outside of the bind mount. This is challenging to fix and doubly
so because all obvious solutions must touch code that is in the
performance part of pathname resolution.
As mentioned above there is also a question of how to ensure that
developers by accident or with purpose do not introduce exectuable
files on sysfs and proc and in doing so introduce security regressions
in the current userspace that will not be immediately obvious and as
such are likely to require breaking userspace in painful ways once
they are recognized"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ebiederm/user-namespace:
vfs: Remove incorrect debugging WARN in prepend_path
mnt: Update fs_fully_visible to test for permanently empty directories
sysfs: Create mountpoints with sysfs_create_mount_point
sysfs: Add support for permanently empty directories to serve as mount points.
kernfs: Add support for always empty directories.
proc: Allow creating permanently empty directories that serve as mount points
sysctl: Allow creating permanently empty directories that serve as mountpoints.
fs: Add helper functions for permanently empty directories.
vfs: Ignore unlocked mounts in fs_fully_visible
mnt: Modify fs_fully_visible to deal with locked ro nodev and atime
mnt: Refactor the logic for mounting sysfs and proc in a user namespace
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/ohad/remoteproc
Pull remoteproc updates from Ohad Ben-Cohen:
- remoteproc fixes/cleanups from Suman Anna
- new remoteproc TI Wakeup M3 driver from Dave Gerlach
- remoteproc core support for TI's Wakeup M3 driver from both Dave and Suman
- tiny remoteproc build fix from myself
* tag 'remoteproc-4.2' of git://git.kernel.org/pub/scm/linux/kernel/git/ohad/remoteproc:
remoteproc: fix !CONFIG_OF build breakage
remoteproc/wkup_m3: add a remoteproc driver for TI Wakeup M3
Documentation: dt: add bindings for TI Wakeup M3 processor
remoteproc: add a rproc ops for performing address translation
remoteproc: introduce rproc_get_by_phandle API
remoteproc: fix various checkpatch warnings
remoteproc/davinci: fix quoted split string checkpatch warning
remoteproc/ste: add blank lines after declarations
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/ohad/hwspinlock
Pull hwspinlock updates from Ohad Ben-Cohen:
- hwspinlock core DT support from Suman Anna
- OMAP hwspinlock DT support from Suman Anna
- QCOM hwspinlock DT support from Bjorn Andersson
- a new CSR atlas7 hwspinlock driver from Wei Chen
- CSR atlas7 hwspinlock DT binding document from Wei Chen
- a tiny QCOM hwspinlock driver fix from Bjorn Andersson
* tag 'hwspinlock-4.2' of git://git.kernel.org/pub/scm/linux/kernel/git/ohad/hwspinlock:
hwspinlock: qcom: Correct msb in regmap_field
DT: hwspinlock: add the CSR atlas7 hwspinlock bindings document
hwspinlock: add a CSR atlas7 driver
hwspinlock: qcom: Add support for Qualcomm HW Mutex block
DT: hwspinlock: Add binding documentation for Qualcomm hwmutex
hwspinlock/omap: add support for dt nodes
Documentation: dt: add the omap hwspinlock bindings document
hwspinlock/core: add device tree support
Documentation: dt: add common bindings for hwspinlock
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux
Pull arm64 fixes (and cleanups) from Catalin Marinas:
"Various arm64 fixes:
- suspicious RCU usage warning
- BPF (out of bounds array read and endianness conversion)
- perf (of_node usage after of_node_put, cpu_pmu->plat_device
assignment)
- huge pmd/pud check for value 0
- rate-limiting should only take unhandled signals into account
Clean-up:
- incorrect use of pgprot_t type
- unused header include
- __init annotation to arm_cpuidle_init
- pr_debug instead of pr_error for disabled GICC entries in
ACPI/MADT"
* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
arm64: Fix show_unhandled_signal_ratelimited usage
ARM64 / SMP: Switch pr_err() to pr_debug() for disabled GICC entry
arm64: cpuidle: add __init section marker to arm_cpuidle_init
arm64: Don't report clear pmds and puds as huge
arm64: perf: fix unassigned cpu_pmu->plat_device when probing PMU PPIs
arm64: perf: Don't use of_node after putting it
arm64: fix incorrect use of pgprot_t variable
arm64/hw_breakpoint.c: remove unnecessary header
arm64: bpf: fix endianness conversion bugs
arm64: bpf: fix out-of-bounds read in bpf2a64_offset()
ARM64: smp: Fix suspicious RCU usage with ipi tracepoints
|
|
Pull nios2 update from Ley Foon Tan:
"Check number of timer instances"
* tag 'nios2-v4.2' of git://git.rocketboards.org/linux-socfpga-next:
nios2: check number of timer instances
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jdelvare/staging
Pull more hwmon updates from Jean Delvare.
* 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jdelvare/staging:
hwmon: (w83627ehf) Use swap() in w82627ehf_swap_tempreg()
hwmon: Document which I2C addresses can be probed
hwmon: (w83792d) Additional PWM outputs support
|
|
Pull block fixes from Jens Axboe:
"Mainly sending this off now for the writeback fixes, since they fix a
real regression introduced with the cgroup writeback changes. The
NVMe fix could wait for next pull for this series, but it's simple
enough that we might as well include it.
This contains:
- two cgroup writeback fixes from Tejun, fixing a user reported issue
with luks crypt devices hanging when being closed.
- NVMe error cleanup fix from Jon Derrick, fixing a case where we'd
attempt to free an unregistered IRQ"
* 'for-linus' of git://git.kernel.dk/linux-block:
NVMe: Fix irq freeing when queue_request_irq fails
writeback: don't drain bdi_writeback_congested on bdi destruction
writeback: don't embed root bdi_writeback_congested in bdi_writeback
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tomba/linux
Pull fbdev fix from Tomi Valkeinen:
"Fix display regression on TI AM4xxx boards"
* tag 'fbdev-fixes-4.2' of git://git.kernel.org/pub/scm/linux/kernel/git/tomba/linux:
OMAPDSS: fix probing if rfbi device is enabled
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/bp/bp
Pull EDAC fix from Borislav Petkov:
"A build fix for octeon_edac from Aaro Koskinen"
* tag 'edac_urgent_for_4.2' of git://git.kernel.org/pub/scm/linux/kernel/git/bp/bp:
EDAC, octeon: Fix broken build due to model helper renames
|
|
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Added Hyper-V crash msrs values - HV_X64_MSR_CRASH*.
Signed-off-by: Andrey Smetanin <asmetanin@virtuozzo.com>
Signed-off-by: Denis V. Lunev <den@openvz.org>
Reviewed-by: Peter Hornyack <peterhornyack@google.com>
CC: Paolo Bonzini <pbonzini@redhat.com>
CC: Gleb Natapov <gleb@kernel.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
Commit 609e36d372ad ("KVM: x86: pass host_initiated to functions that
read MSRs") modified kvm_get_msr_common function to use msr_info->data
instead of data but missed one occurrence. Replace it and remove the
unused local variable.
Fixes: 609e36d372ad ("KVM: x86: pass host_initiated to functions that
read MSRs")
Signed-off-by: Nicolas Iooss <nicolas.iooss_linux@m4x.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
Eric noticed problems with vhost-scsi and virtio-ccw: vhost-scsi
complained about overwriting values in the config space, which
was triggered by a broken implementation of virtio-ccw's config
get/set routines. It was probably sheer luck that we did not hit
this before.
When writing a value to the config space, the WRITE_CONF ccw will
always write from the beginning of the config space up to and
including the value to be set. If the config space up to the value
has not yet been retrieved from the device, however, we'll end up
overwriting values. Keep track of the known config space and update
if needed to avoid this.
Moreover, READ_CONF will only read the number of bytes it has been
instructed to retrieve, so we must not copy more than that to the
buffer, or we might overwrite trailing values.
Reported-by: Eric Farman <farman@linux.vnet.ibm.com>
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Reviewed-by: Eric Farman <farman@linux.vnet.ibm.com>
Tested-by: Eric Farman <farman@linux.vnet.ibm.com>
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Cc: stable@vger.kernel.org
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
Memory-mapped LVT0 register already contains the new value when APICv
traps so we can't directly detect a change.
Memorize a bit we are interested in to enable legacy NMI watchdog.
Suggested-by: Yoshida Nobuo <yoshida.nb@ncos.nec.co.jp>
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
Legacy NMI watchdog didn't work after migration/resume, because
vapics_in_nmi_mode was left at 0.
Cc: stable@vger.kernel.org
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
Writes were a bit racy, but hard to turn into a bug at the same time.
(Particularly because modern Linux doesn't use this feature anymore.)
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
[Actually the next patch makes it much, much easier to trigger the race
so I'm including this one for stable@ as well. - Paolo]
Cc: stable@vger.kernel.org
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
Commit 1cde2930e154 ("sched/preempt: Add static_key() to preempt_notifiers")
had two problems. First, the preempt-notifier API needs to sleep with the
addition of the static_key, we do however need to hold off preemption
while modifying the preempt notifier list, otherwise a preemption could
observe an inconsistent list state. KVM correctly registers and
unregisters preempt notifiers with preemption disabled, so the sleep
caused dmesg splats.
Second, KVM registers and unregisters preemption notifiers very often
(in vcpu_load/vcpu_put). With a single uniprocessor guest the static key
would move between 0 and 1 continuously, hitting the slow path on every
userspace exit.
To fix this, wrap the static_key inc/dec in a new API, and call it from
KVM.
Fixes: 1cde2930e154 ("sched/preempt: Add static_key() to preempt_notifiers")
Reported-by: Pontus Fuchs <pontus.fuchs@gmail.com>
Reported-by: Takashi Iwai <tiwai@suse.de>
Tested-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
Commit 86dca36e6ba introduced ratelimited usage for
'unhandled_signal' messages.
The commit checks the ratelimit irrespective of whether
the signal is handled or not, which is wrong and leads
to false reports like the below in dmesg :
__do_user_fault: 127 callbacks suppressed
Do the ratelimit check only if the signal is unhandled.
Fixes: 86dca36e6ba0 ("arm64: use private ratelimit state along with show_unhandled_signals")
Cc: Vladimir Murzin <Vladimir.Murzin@arm.com>
Signed-off-by: Suzuki K. Poulose <suzuki.poulose@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
|
|
Use kernel.h macro definition.
Thanks to Julia Lawall for Coccinelle scripting support.
Signed-off-by: Fabian Frederick <fabf@skynet.be>
Signed-off-by: Jean Delvare <jdelvare@suse.de>
|
|
Add an item to the checklist when submitting a new hwmon driver: only
some I2C addresses can be probed, others should not for safety
reasons.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
|
|
Add pwm[4-7] and the associated pwm[4-7]_mode attributes.
Signed-off-by: Roger Lucas <vt8231@hiddenengine.co.uk>
Signed-off-by: Jean Delvare <jdelvare@suse.de>
|
|
It is normal that firmware presents GICC entry or entries (processors)
with disabled flag in ACPI MADT, taking a system of 16 cpus for example,
ACPI firmware may present 8 ebabled first with another 8 cpus disabled
in MADT, the disabled cpus can be hot-added later.
Firmware may also present more cpus than the hardware actually has, but
disabled the unused ones, and easily enable it when the hardware has such
cpus to make the firmware code scalable.
So that's not an error for disabled cpus in MADT, we can switch pr_err()
to pr_debug() to make the boot a little quieter by default.
Since hwid for disabled cpus often are invalid, and we check invalid hwid
first in the code, for use case that hot add cpus later will be filtered
out and will not be counted in possible cups, so move this check before
the hwid one to prepare the code to count for disabeld cpus when cpu
hot-plug is introduced.
Signed-off-by: Hanjun Guo <hanjun.guo@linaro.org>
Reviewed-by: Al Stone <ahs3@redhat.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull ACPICA updates from Rafael Wysocki:
"Additional ACPICA material for v4.2-rc1
This will update the ACPICA code in the kernel to upstream revision
20150619 (a bug-fix release mostly including stable-candidate fixes)
and restore an earlier ACPICA commit that had to be reverted due to a
regression introduced by it (the regression is addressed by
blacklisting the only known system affected by it to date).
The only new feature added by this update is the support for
overriding objects in the ACPI namespace and a new ACPI table that can
be used for that called the Override System Definition Table (OSDT).
That should allow us to "patch" the ACPI namespace built from
incomplete or incorrect ACPI System Definition tables (DSDT, SSDT)
during system startup without the need to provide replacements for all
of those tables in the future.
Specifics:
- Fix system resume problems related to 32-bit and 64-bit versions of
the Firmware ACPI Control Structure (FACS) in the firmare (Lv
Zheng)
- Fix double initialization of the FACS (Lv Zheng)
- Add _CLS object processing code to ACPICA (Suravee Suthikulpanit)
- Add support for the (currently missing) new GIC version field in
the Multiple APIC Description Table (MADT) (Hanjun Guo)
- Add support for overriding objects in the ACPI namespace to ACPICA
and OSDT support (Lv Zheng, Bob Moore, Zhang Rui)
- Updates related to the TCPA and TPM2 ACPI tables (Bob Moore)
- Restore the commit modifying _REV to always return "2" (as required
by ACPI 6) and add a blacklisting mechanism for systems that may be
affected by that change (Rafael J Wysocki)
- Assorted fixes and cleanups (Bob Moore, Lv Zheng, Sascha Wildner)"
* tag 'acpica-4.2-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (28 commits)
Revert 'Revert "ACPICA: Permanently set _REV to the value '2'."'
ACPI / init: Make it possible to override _REV
ACPICA: Update version to 20150619
ACPICA: Comment update, no functional change
ACPICA: Update TPM2 ACPI table
ACPICA: Update definitions for the TCPA and TPM2 ACPI tables
ACPICA: Split C library prototypes to new header
ACPICA: De-macroize calls to standard C library functions
ACPI / acpidump: Update acpidump manual
ACPICA: acpidump: Convert the default behavior to dump from /sys/firmware/acpi/tables
ACPICA: acpidump: Allow customized tables to be dumped without accessing /dev/mem
ACPICA: Cleanup output for the ASL Debug object
ACPICA: Update for acpi_install_table memory types
ACPICA: Namespace: Change namespace override to avoid node deletion
ACPICA: Namespace: Add support of OSDT table
ACPICA: Namespace: Add support to allow overriding objects
ACPICA: ACPI 6.0: Add values for MADT GIC version field
ACPICA: Utilities: Add _CLS processing
ACPICA: Add dragon_fly support to unix file mapping file
ACPICA: EFI: Add EFI interface definitions to eliminate dependency of GNU EFI
...
|
|
It's a bug in our Makefile rules, make it show what the changing
certificate list was, and make it a warning so that people actually see
it.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
