| Age | Commit message (Collapse) | Author |
|---|
|
commit ff45000fcb56b5b0f1a14a865d3541746d838a0a upstream.
The boot wrapper performs its own relocations and does not require
PT_INTERP segment. However currently we don't tell the linker that.
Prior to binutils 2.28 that works OK. But since binutils commit
1a9ccd70f9a7 ("Fix the linker so that it will not silently generate ELF
binaries with invalid program headers. Fix readelf to report such
invalid binaries.") binutils tries to create a program header segment
due to PT_INTERP, and the link fails because there is no space for it:
ld: arch/powerpc/boot/zImage.pseries: Not enough room for program headers, try linking with -N
ld: final link failed: Bad value
So tell the linker not to do that, by passing --no-dynamic-linker.
Reported-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
[mpe: Drop dependency on ld-version.sh and massage change log]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 6dff5b67054e17c91bd630bcdda17cfca5aa4215 upstream.
GCC 5 generates different code for this bootwrapper null check that
causes the PS3 to hang very early in its bootup. This check is of
limited value, so just get rid of it.
Signed-off-by: Geoff Levand <geoff@infradead.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit f87f253bac3ce4a4eb2a60a1ae604d74e65f9042 upstream.
From 80f23935cadb ("powerpc: Convert cmp to cmpd in idle enter sequence"):
PowerPC's "cmp" instruction has four operands. Normally people write
"cmpw" or "cmpd" for the second cmp operand 0 or 1. But, frequently
people forget, and write "cmp" with just three operands.
With older binutils this is silently accepted as if this was "cmpw",
while often "cmpd" is wanted. With newer binutils GAS will complain
about this for 64-bit code. For 32-bit code it still silently assumes
"cmpw" is what is meant.
In this case, cmpwi is called for, so this is just a build fix for
new toolchains.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 1cded9d2974fe4fe339fc0ccd6638b80d465ab2c upstream.
There are two problems with refcounting of auth_gss messages.
First, the reference on the pipe->pipe list (taken by a call
to rpc_queue_upcall()) is not counted. It seems to be
assumed that a message in pipe->pipe will always also be in
pipe->in_downcall, where it is correctly reference counted.
However there is no guaranty of this. I have a report of a
NULL dereferences in rpc_pipe_read() which suggests a msg
that has been freed is still on the pipe->pipe list.
One way I imagine this might happen is:
- message is queued for uid=U and auth->service=S1
- rpc.gssd reads this message and starts processing.
This removes the message from pipe->pipe
- message is queued for uid=U and auth->service=S2
- rpc.gssd replies to the first message. gss_pipe_downcall()
calls __gss_find_upcall(pipe, U, NULL) and it finds the
*second* message, as new messages are placed at the head
of ->in_downcall, and the service type is not checked.
- This second message is removed from ->in_downcall and freed
by gss_release_msg() (even though it is still on pipe->pipe)
- rpc.gssd tries to read another message, and dereferences a pointer
to this message that has just been freed.
I fix this by incrementing the reference count before calling
rpc_queue_upcall(), and decrementing it if that fails, or normally in
gss_pipe_destroy_msg().
It seems strange that the reply doesn't target the message more
precisely, but I don't know all the details. In any case, I think the
reference counting irregularity became a measureable bug when the
extra arg was added to __gss_find_upcall(), hence the Fixes: line
below.
The second problem is that if rpc_queue_upcall() fails, the new
message is not freed. gss_alloc_msg() set the ->count to 1,
gss_add_msg() increments this to 2, gss_unhash_msg() decrements to 1,
then the pointer is discarded so the memory never gets freed.
Fixes: 9130b8dbc6ac ("SUNRPC: allow for upcalls for same uid but different gss service")
Link: https://bugzilla.opensuse.org/show_bug.cgi?id=1011250
Signed-off-by: NeilBrown <neilb@suse.com>
Signed-off-by: Trond Myklebust <trond.myklebust@primarydata.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 54e4a0dfa25d9365c4e80a639e80d9213eb6edbe upstream.
We must not call nfs_pageio_init_read() on a new nfs_pageio_descriptor
while holding a reference to a layout segment, as that can deadlock
pnfs_update_layout().
Fixes: d67ae825a59d6 ("pnfs/flexfiles: Add the FlexFile Layout Driver")
Signed-off-by: Trond Myklebust <trond.myklebust@primarydata.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit ae5a459d5f65c3e83f3e14068dde5fb9c9d81807 upstream.
We must ensure that we don't schedule a layoutreturn if the layout stateid
has been marked as invalid.
Fixes: 2a59a0411671e ("pNFS: Fix pnfs_set_layout_stateid() to clear...")
Signed-off-by: Trond Myklebust <trond.myklebust@primarydata.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 7b650994ab07434ae58a247dc9ac87d2488ca75c upstream.
If we no longer hold any layout segments, we're normally expected to
consider the layout stateid to be invalid. However we cannot assume this
if we're about to, or in the process of sending a layoutreturn.
Fixes: 334a8f37115b ("pNFS: Don't forget the layout stateid if...")
Signed-off-by: Trond Myklebust <trond.myklebust@primarydata.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 6604b203fb6394ed1f24c21bfa3c207e5ae8e461 upstream.
If there is an I/O error, we should not call LAYOUTGET until the
LAYOUTRETURN that reports the error is complete.
Signed-off-by: Trond Myklebust <trond.myklebust@primarydata.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit c0cf3ef5e0f47e385920450b245d22bead93e7ad upstream.
What matters when deciding if we should make a page uptodate is
not how much we _wanted_ to copy, but how much we actually have
copied. As it is, on architectures that do not zero tail on
short copy we can leave uninitialized data in page marked uptodate.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 5c056fdc5b474329037f2aa18401bd73033e0ce0 upstream.
After sending an authorizer (ceph_x_authorize_a + ceph_x_authorize_b),
the client gets back a ceph_x_authorize_reply, which it is supposed to
verify to ensure the authenticity and protect against replay attacks.
The code for doing this is there (ceph_x_verify_authorizer_reply(),
ceph_auth_verify_authorizer_reply() + plumbing), but it is never
invoked by the the messenger.
AFAICT this goes back to 2009, when ceph authentication protocols
support was added to the kernel client in 4e7a5dcd1bba ("ceph:
negotiate authentication protocol; implement AUTH_NONE protocol").
The second param of ceph_connection_operations::verify_authorizer_reply
is unused all the way down. Pass 0 to facilitate backporting, and kill
it in the next commit.
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
Reviewed-by: Sage Weil <sage@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 6496ebd7edf446fccf8266a1a70ffcb64252593e upstream.
One some systems, the firmware does not allow certain PCI devices to be put
in deep D-states. This can cause problems for wakeup signalling, if the
device does not support PME# in the deepest allowed suspend state. For
example, Pierre reports that on his system, ACPI does not permit his xHCI
host controller to go into D3 during runtime suspend -- but D3 is the only
state in which the controller can generate PME# signals. As a result, the
controller goes into runtime suspend but never wakes up, so it doesn't work
properly. USB devices plugged into the controller are never detected.
If the device relies on PME# for wakeup signals but is not capable of
generating PME# in the target state, the PCI core should accurately report
that it cannot do wakeup from runtime suspend. This patch modifies the
pci_dev_run_wake() routine to add this check.
Reported-by: Pierre de Villemereuil <flyos@mailoo.org>
Tested-by: Pierre de Villemereuil <flyos@mailoo.org>
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
CC: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 91c42b72f8e8b45961ff05a05009b644e6316ca2 upstream.
hw_stats is a pointer to i40_iw_dev_stats struct in i40iw_get_hw_stats().
Use hw_stats and not &hw_stats in the memcpy to copy the i40iw device stats
data into rdma_hw_stats counters.
Fixes: b40f4757daa1 ("IB/core: Make device counter infrastructure dynamic")
Signed-off-by: Shiraz Saleem <shiraz.saleem@intel.com>
Signed-off-by: Faisal Latif <faisal.latif@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 3f9ca75516a7e581ff803f751a869c1da5ae5fa5 upstream.
New inode operations were forgotten to be added to bad_inode. Most of the
time the op is checked for NULL before being called but marking the inode
bad and the check can race (very unlikely).
However in case of ->get_link() only DCACHE_SYMLINK_TYPE is checked before
calling the op, so there's no race and will definitely oops when trying to
follow links on such a beast.
Also remove comments about extinct ops.
Signed-off-by: Miklos Szeredi <mszeredi@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 5a8a6b89c15766446d845671d574a9243b6d8786 upstream.
We were assigning I2C bus controller instead of client as parent device.
Besides being logically wrong, it messed up with devm handling of input
device. As a result we were leaving input device and event node behind
after rmmod-ing the driver, which lead to a kernel oops if one were to
access the event node later.
Let's remove the assignment and rely on devm_input_allocate_device() to
set it up properly for us.
Signed-off-by: Jingkui Wang <jkwang@google.com>
Fixes: 7132fe4f5687 ("Input: drv260x - add TI drv260x haptics driver")
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit d183e4efcae8d88a2f252e546978658ca6d273cc upstream.
A break is missing resulting in the hue control enabling or disabling
the decode completely. Fix it.
Fixes: c43875f66140 ("[media] tvp5150: replace MEDIA_ENT_F_CONN_TEST by a control")
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 5fc4b067ec082c3127e0156f800769b7e0dce078 upstream.
This fixes a lockup at device probing which happens on some solo6010
hardware samples. This is a regression introduced by commit e1ceb25a1569
("[media] SOLO6x10: remove unneeded register locking and barriers")
The observed lockup happens in solo_set_motion_threshold() called from
solo_motion_config().
This extra "flushing" is not fundamentally needed for every write, but
apparently the code in driver assumes such behaviour at last in some
places.
Actual fix was proposed by Hans Verkuil.
Fixes: e1ceb25a1569 ("[media] SOLO6x10: remove unneeded register locking and barriers")
Signed-off-by: Andrey Utkin <andrey.utkin@corp.bluecherry.net>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 3467c9a7e7f9209a9ecd8f9db65b04a323a13932 upstream.
s5p_mfc_alloc_memdev() function lacks proper releasing
of allocated device in case of reserved memory initialization
failure. This results in NULL pointer dereference:
[ 2.828457] Unable to handle kernel NULL pointer dereference at virtual address 00000001
[ 2.835089] pgd = c0004000
[ 2.837752] [00000001] *pgd=00000000
[ 2.844696] Internal error: Oops: 5 [#1] PREEMPT SMP ARM
[ 2.848680] Modules linked in:
[ 2.851722] CPU: 1 PID: 1 Comm: swapper/0 Not tainted 4.8.0-rc6-00002-gafa1b97 #878
[ 2.859357] Hardware name: SAMSUNG EXYNOS (Flattened Device Tree)
[ 2.865433] task: ef080000 task.stack: ef06c000
[ 2.869952] PC is at strcmp+0x0/0x30
[ 2.873508] LR is at platform_match+0x84/0xac
[ 2.877847] pc : [<c032621c>] lr : [<c03f65e8>] psr: 20000013
[ 2.877847] sp : ef06dea0 ip : 00000000 fp : 00000000
[ 2.889303] r10: 00000000 r9 : c0b34848 r8 : c0b1e968
[ 2.894511] r7 : 00000000 r6 : 00000001 r5 : c086e7fc r4 : eeb8e010
[ 2.901021] r3 : 0000006d r2 : 00000000 r1 : c086e7fc r0 : 00000001
[ 2.907533] Flags: nzCv IRQs on FIQs on Mode SVC_32 ISA ARM Segment none
[ 2.914649] Control: 10c5387d Table: 4000404a DAC: 00000051
[ 2.920378] Process swapper/0 (pid: 1, stack limit = 0xef06c210)
[ 2.926367] Stack: (0xef06dea0 to 0xef06e000)
[ 2.930711] dea0: eeb8e010 c0c2d91c c03f4a6c c03f4a8c 00000000 c0c2d91c c03f4a6c c03f2fc8
[ 2.938870] dec0: ef003274 ef10c4c0 c0c2d91c ef10cc80 c0c21270 c03f3fa4 c09c1be8 c0c2d91c
[ 2.947028] dee0: 00000006 c0c2d91c 00000006 c0b3483c c0c47000 c03f5314 c0c2d908 c0b5fed8
[ 2.955188] df00: 00000006 c010178c 60000013 c0a4ef14 00000000 c06feaa0 ef080000 60000013
[ 2.963347] df20: 00000000 c0c095c8 efffca76 c0816b8c 000000d5 c0134098 c0b34848 c09d6cdc
[ 2.971506] df40: c0a4de70 00000000 00000006 00000006 c0c09568 efffca40 c0b5fed8 00000006
[ 2.979665] df60: c0b3483c c0c47000 000000d5 c0b34848 c0b005a4 c0b00d84 00000006 00000006
[ 2.987824] df80: 00000000 c0b005a4 00000000 c06fb4d8 00000000 00000000 00000000 00000000
[ 2.995983] dfa0: 00000000 c06fb4e0 00000000 c01079b8 00000000 00000000 00000000 00000000
[ 3.004142] dfc0: 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
[ 3.012302] dfe0: 00000000 00000000 00000000 00000000 00000013 00000000 ffffffff ffffffff
[ 3.020469] [<c032621c>] (strcmp) from [<c03f65e8>] (platform_match+0x84/0xac)
[ 3.027672] [<c03f65e8>] (platform_match) from [<c03f4a8c>] (__driver_attach+0x20/0xb0)
[ 3.035654] [<c03f4a8c>] (__driver_attach) from [<c03f2fc8>] (bus_for_each_dev+0x54/0x88)
[ 3.043812] [<c03f2fc8>] (bus_for_each_dev) from [<c03f3fa4>] (bus_add_driver+0xe8/0x1f4)
[ 3.051971] [<c03f3fa4>] (bus_add_driver) from [<c03f5314>] (driver_register+0x78/0xf4)
[ 3.059958] [<c03f5314>] (driver_register) from [<c010178c>] (do_one_initcall+0x3c/0x16c)
[ 3.068123] [<c010178c>] (do_one_initcall) from [<c0b00d84>] (kernel_init_freeable+0x120/0x1ec)
[ 3.076802] [<c0b00d84>] (kernel_init_freeable) from [<c06fb4e0>] (kernel_init+0x8/0x118)
[ 3.084958] [<c06fb4e0>] (kernel_init) from [<c01079b8>] (ret_from_fork+0x14/0x3c)
[ 3.092506] Code: 1afffffb e12fff1e e1a03000 eafffff7 (e4d03001)
[ 3.098618] ---[ end trace 511bf9d750810709 ]---
[ 3.103207] Kernel panic - not syncing: Attempted to kill init! exitcode=0x0000000b
This patch fixes this issue.
Fixes: c79667dd93b084fe412bcfe7fbf0ba43f7dec520 ("media: s5p-mfc: replace custom
reserved memory handling code with generic one")
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit d930b5b5bf122a61952cfebabb1e618682a2631a upstream.
A register used to identify chip during probe was overwritten during
firmware download and due to that later probe's for warm chip were
failing. Detect chip from the another register, which is located on
different register bank 2.
Fixes: 7908fad99a6c ("[media] mn88473: finalize driver")
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 365fe4e0ce218dc5ad10df17b150a366b6015499 upstream.
A register used to identify chip during probe was overwritten during
firmware download and due to that later probe's for warm chip were
failing. Detect chip from the another register, which is located on
different register bank 2.
Fixes: 94d0eaa41987 ("[media] mn88472: move out of staging to media")
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit fba332b079029c2f4f7e84c1c1cd8e3867310c90 upstream.
Code that dereferences the struct net_device ip_ptr member must be
protected with an in_dev_get() / in_dev_put() pair. Hence insert
calls to these functions.
Fixes: commit 7b85627b9f02 ("IB/cma: IBoE (RoCE) IP-based GID addressing")
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Reviewed-by: Moni Shoua <monis@mellanox.com>
Cc: Or Gerlitz <ogerlitz@mellanox.com>
Cc: Roland Dreier <roland@purestorage.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit e259934d4df7f99f2a5c2c4f074f6a55bd4b1722 upstream.
A socket is associated with every QP by the rxe driver but sock_release()
is never called. Add a call to sock_release() in rxe_qp_cleanup().
Fixes: commit 8700e3e7c48A5 ("Add Soft RoCE driver")
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Cc: Moni Shoua <monis@mellanox.com>
Cc: Kamal Heib <kamalh@mellanox.com>
Cc: Amir Vadai <amirv@mellanox.com>
Cc: Haggai Eran <haggaie@mellanox.com>
Reviewed-by: Moni Shoua <monis@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit d3a2418ee36a59bc02e9d454723f3175dcf4bfd9 upstream.
This patch avoids that Coverity complains about not checking the
ib_find_pkey() return value.
Fixes: commit 547af76521b3 ("IB/multicast: Report errors on multicast groups if P_key changes")
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Cc: Sean Hefty <sean.hefty@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 11b642b84e8c43e8597de031678d15c08dd057bc upstream.
This patch avoids that Coverity reports the following:
Using uninitialized value port_attr.state when calling printk
Fixes: commit 94232d9ce817 ("IPoIB: Start multicast join process only on active ports")
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Cc: Erez Shitrit <erezsh@mellanox.com>
Reviewed-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 2fe2f378dd45847d2643638c07a7658822087836 upstream.
The array ib_mad_mgmt_class_table.method_table has MAX_MGMT_CLASS
(80) elements. Hence compare the array index with that value instead
of with IB_MGMT_MAX_METHODS (128). This patch avoids that Coverity
reports the following:
Overrunning array class->method_table of 80 8-byte elements at element index 127 (byte offset 1016) using index convert_mgmt_class(mad_hdr->mgmt_class) (which evaluates to 127).
Fixes: commit b7ab0b19a85f ("IB/mad: Verify mgmt class in received MADs")
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Cc: Sean Hefty <sean.hefty@intel.com>
Reviewed-by: Hal Rosenstock <hal@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 794de08a16cf1fc1bf785dc48f66d36218cf6d88 upstream.
Both the wakeup and irqsoff tracers can use the function graph tracer when
the display-graph option is set. The problem is that they ignore the notrace
file, and record the entry of functions that would be ignored by the
function_graph tracer. This causes the trace->depth to be recorded into the
ring buffer. The set_graph_notrace uses a trick by adding a large negative
number to the trace->depth when a graph function is to be ignored.
On trace output, the graph function uses the depth to record a stack of
functions. But since the depth is negative, it accesses the array with a
negative number and causes an out of bounds access that can cause a kernel
oops or corrupt data.
Have the print functions handle cases where a tracer still records functions
even when they are in set_graph_notrace.
Also add warnings if the depth is below zero before accessing the array.
Note, the function graph logic will still prevent the return of these
functions from being recorded, which means that they will be left hanging
without a return. For example:
# echo '*spin*' > set_graph_notrace
# echo 1 > options/display-graph
# echo wakeup > current_tracer
# cat trace
[...]
_raw_spin_lock() {
preempt_count_add() {
do_raw_spin_lock() {
update_rq_clock();
Where it should look like:
_raw_spin_lock() {
preempt_count_add();
do_raw_spin_lock();
}
update_rq_clock();
Cc: Namhyung Kim <namhyung.kim@lge.com>
Fixes: 29ad23b00474 ("ftrace: Add set_graph_notrace filter")
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 9d85eb9119f4eeeb48e87adfcd71f752655700e9 upstream.
The logical package management has several issues:
- The APIC ids provided by ACPI are not required to be the same as the
initial APIC id which can be retrieved by CPUID. The APIC ids provided
by ACPI are those which are written by the BIOS into the APIC. The
initial id is set by hardware and can not be changed. The hardware
provided ids contain the real hardware package information.
Especially AMD sets the effective APIC id different from the hardware id
as they need to reserve space for the IOAPIC ids starting at id 0.
As a consequence those machines trigger the currently active firmware
bug printouts in dmesg, These are obviously wrong.
- Virtual machines have their own interesting of enumerating APICs and
packages which are not reliably covered by the current implementation.
The sizing of the mapping array has been tweaked to be generously large to
handle systems which provide a wrong core count when HT is disabled so the
whole magic which checks for space in the physical hotplug case is not
needed anymore.
Simplify the whole machinery and do the mapping when the CPU starts and the
CPUID derived physical package information is available. This solves the
observed problems on AMD machines and works for the virtualization issues
as well.
Remove the extra call from XEN cpu bringup code as it is not longer
required.
Fixes: d49597fd3bc7 ("x86/cpu: Deal with broken firmware (VMWare/XEN)")
Reported-and-tested-by: Borislav Petkov <bp@suse.de>
Tested-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Juergen Gross <jgross@suse.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: M. Vefa Bicakci <m.v.b@runbox.com>
Cc: xen-devel <xen-devel@lists.xen.org>
Cc: Charles (Chas) Williams <ciwillia@brocade.com>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Alok Kataria <akataria@vmware.com>
Link: http://lkml.kernel.org/r/alpine.DEB.2.20.1612121102260.3429@nanos
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit e74e259939275a5dd4e0d02845c694f421e249ad upstream.
Without this patch, the Asus X45U wireless card can't be turned
on (hard-blocked), but after a suspend/resume it just starts working.
Following this bug report[1], there are other cases like this one, but
this Asus is the only model that I can test.
[1] https://ubuntuforums.org/showthread.php?t=2181558
Signed-off-by: Marcos Paulo de Souza <marcos.souza.org@gmail.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
to it
commit 847fa1a6d3d00f3bdf68ef5fa4a786f644a0dd67 upstream.
With new binutils, gcc may get smart with its optimization and change a jmp
from a 5 byte jump to a 2 byte one even though it was jumping to a global
function. But that global function existed within a 2 byte radius, and gcc
was able to optimize it. Unfortunately, that jump was also being modified
when function graph tracing begins. Since ftrace expected that jump to be 5
bytes, but it was only two, it overwrote code after the jump, causing a
crash.
This was fixed for x86_64 with commit 8329e818f149, with the same subject as
this commit, but nothing was done for x86_32.
Fixes: d61f82d06672 ("ftrace: use dynamic patching for updating mcount calls")
Reported-by: Colin Ian King <colin.king@canonical.com>
Tested-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit f83f12d660d11718d3eed9d979ee03e83aa55544 upstream.
These fields are 64 bit, using le32_to_cpu and friends
on these will not do the right thing.
Fix this up.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 5716863e0f8251d3360d4cbfc0e44e08007075df upstream.
fsnotify_unmount_inodes() plays complex tricks to pin next inode in the
sb->s_inodes list when iterating over all inodes. Furthermore the code has a
bug that if the current inode is the last on i_sb_list that does not have e.g.
I_FREEING set, then we leave next_i pointing to inode which may get removed
from the i_sb_list once we drop s_inode_list_lock thus resulting in
use-after-free issues (usually manifesting as infinite looping in
fsnotify_unmount_inodes()).
Fix the problem by keeping current inode pinned somewhat longer. Then we can
make the code much simpler and standard.
Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit ef85b67385436ddc1998f45f1d6a210f935b3388 upstream.
When L2 exits to L0 due to "exception or NMI", software exceptions
(#BP and #OF) for which L1 has requested an intercept should be
handled by L1 rather than L0. Previously, only hardware exceptions
were forwarded to L1.
Signed-off-by: Jim Mattson <jmattson@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit f064a0de1579fabded8990bed93971e30deb9ecb upstream.
The hashed page table MMU in POWER processors can update the R
(reference) and C (change) bits in a HPTE at any time until the
HPTE has been invalidated and the TLB invalidation sequence has
completed. In kvmppc_h_protect, which implements the H_PROTECT
hypercall, we read the HPTE, modify the second doubleword,
invalidate the HPTE in memory, do the TLB invalidation sequence,
and then write the modified value of the second doubleword back
to memory. In doing so we could overwrite an R/C bit update done
by hardware between when we read the HPTE and when the TLB
invalidation completed. To fix this we re-read the second
doubleword after the TLB invalidation and OR in the (possibly)
new values of R and C. We can use an OR since hardware only ever
sets R and C, never clears them.
This race was found by code inspection. In principle this bug could
cause occasional guest memory corruption under host memory pressure.
Fixes: a8606e20e41a ("KVM: PPC: Handle some PAPR hcalls in the kernel", 2011-06-29)
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 0d808df06a44200f52262b6eb72bcb6042f5a7c5 upstream.
When switching from/to a guest that has a transaction in progress,
we need to save/restore the checkpointed register state. Although
XER is part of the CPU state that gets checkpointed, the code that
does this saving and restoring doesn't save/restore XER.
This fixes it by saving and restoring the XER. To allow userspace
to read/write the checkpointed XER value, we also add a new ONE_REG
specifier.
The visible effect of this bug is that the guest may see its XER
value being corrupted when it uses transactions.
Fixes: e4e38121507a ("KVM: PPC: Book3S HV: Add transactional memory support")
Fixes: 0a8eccefcb34 ("KVM: PPC: Book3S HV: Add missing code for transaction reclaim on guest exit")
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit ae2aae2421983f6f68eb7c4692624bc43ea50712 upstream.
Controllers with this PCI ID never shipped outside of
PMCS/Microsemi. Remove the ID from the aacraid driver. smartpqi is the
correct driver for these controllers.
[mkp: patch description]
Reviewed-by: Scott Teel <scott.teel@microsemi.com>
Signed-off-by: Kevin Barnett <kevin.barnett@microsemi.com>
Signed-off-by: Don Brace <don.brace@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit e8d7c33232e5fdfa761c3416539bc5b4acd12db5 upstream.
Current implementation employ 16bit counter of active stripes in lower
bits of bio->bi_phys_segments. If request is big enough to overflow
this counter bio will be completed and freed too early.
Fortunately this not happens in default configuration because several
other limits prevent that: stripe_cache_size * nr_disks effectively
limits count of active stripes. And small max_sectors_kb at lower
disks prevent that during normal read/write operations.
Overflow easily happens in discard if it's enabled by module parameter
"devices_handle_discard_safely" and stripe_cache_size is set big enough.
This patch limits requests size with 256Mb - 8Kb to prevent overflows.
Signed-off-by: Konstantin Khlebnikov <khlebnikov@yandex-team.ru>
Cc: Shaohua Li <shli@kernel.org>
Cc: Neil Brown <neilb@suse.com>
Signed-off-by: Shaohua Li <shli@fb.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 04da73803c05dc1150ccc31cbf93e8cd56679c09 upstream.
The use of IRQF_ONESHOT when registering an interrupt handler with
request_irq() is non-sensical.
Not only that, it also prevents the handler from being threaded when it
otherwise should be w/ IRQ_FORCED_THREADING is enabled. This causes the
following deadlock observed by Sean Nyekjaer on -rt:
Internal error: Oops - BUG: 0 [#1] PREEMPT SMP ARM
[..]
rt_spin_lock_slowlock from queue_kthread_work
queue_kthread_work from sc16is7xx_irq
sc16is7xx_irq [sc16is7xx] from handle_irq_event_percpu
handle_irq_event_percpu from handle_irq_event
handle_irq_event from handle_level_irq
handle_level_irq from generic_handle_irq
generic_handle_irq from mxc_gpio_irq_handler
mxc_gpio_irq_handler from mx3_gpio_irq_handler
mx3_gpio_irq_handler from generic_handle_irq
generic_handle_irq from __handle_domain_irq
__handle_domain_irq from gic_handle_irq
gic_handle_irq from __irq_svc
__irq_svc from rt_spin_unlock
rt_spin_unlock from kthread_worker_fn
kthread_worker_fn from kthread
kthread from ret_from_fork
Fixes: 9e6f4ca3e567 ("sc16is7xx: use kthread_worker for tx_work and irq")
Reported-by: Sean Nyekjaer <sean.nyekjaer@prevas.dk>
Signed-off-by: Josh Cartwright <joshc@ni.com>
Cc: linux-rt-users@vger.kernel.org
Cc: Jakub Kicinski <moorray3@wp.pl>
Cc: linux-serial@vger.kernel.org
Cc: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Julia Cartwright <julia@ni.com>
Acked-by: Jakub Kicinski <kubakici@wp.pl>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 9988f4d577f42f43b7612d755477585f35424af7 upstream.
This fixes build errors seen on gcc-4.9.3 or gcc-5.3.1 for an ARM:
arm-soc/init/initramfs.c: In function 'error':
arm-soc/init/initramfs.c:50:1: error: unrecognizable insn:
}
^
(insn 26 25 27 5 (set (reg:SI 111 [ local_entropy.243 ])
(rotatert:SI (reg:SI 116 [ local_entropy.243 ])
(const_int -30 [0xffffffffffffffe2]))) -1
(nil))
Patch from PaX Team <pageexec@freemail.hu>
Reported-by: Arnd Bergmann <arnd@arndb.de>
Reported-by: Brad Spengler <spender@grsecurity.net>
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 21cbe3cc8a48ff17059912e019fbde28ed54745a upstream.
The ARMv8 architecture allows the cycle counter to be configured
by setting PMSELR_EL0.SEL==0x1f and then accessing PMXEVTYPER_EL0,
hence accessing PMCCFILTR_EL0. But it disallows the use of
PMSELR_EL0.SEL==0x1f to access the cycle counter itself through
PMXEVCNTR_EL0.
Linux itself doesn't violate this rule, but we may end up with
PMSELR_EL0.SEL being set to 0x1f when we enter a guest. If that
guest accesses PMXEVCNTR_EL0, the access may UNDEF at EL1,
despite the guest not having done anything wrong.
In order to avoid this unfortunate course of events (haha!), let's
sanitize PMSELR_EL0 on guest entry. This ensures that the guest
won't explode unexpectedly.
Acked-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 9f88eb4df728aebcd2ddd154d99f1d75b428b897 upstream.
When re-adding crash kernel memory within setup_resources() the
function memblock_add() is used. That function will add memory by
default to node "MAX_NUMNODES" instead of node 0, like the memory
detection code does. In case of !NUMA this will trigger this warning
when the kernel generates the vmemmap:
Usage of MAX_NUMNODES is deprecated. Use NUMA_NO_NODE instead
WARNING: CPU: 0 PID: 0 at mm/memblock.c:1261 memblock_virt_alloc_internal+0x76/0x220
CPU: 0 PID: 0 Comm: swapper Not tainted 4.9.0-rc6 #16
Call Trace:
[<0000000000d0b2e8>] memblock_virt_alloc_try_nid+0x88/0xc8
[<000000000083c8ea>] __earlyonly_bootmem_alloc.constprop.1+0x42/0x50
[<000000000083e7f4>] vmemmap_populate+0x1ac/0x1e0
[<0000000000840136>] sparse_mem_map_populate+0x46/0x68
[<0000000000d0c59c>] sparse_init+0x184/0x238
[<0000000000cf45f6>] paging_init+0xbe/0xf8
[<0000000000cf1d4a>] setup_arch+0xa02/0xae0
[<0000000000ced75a>] start_kernel+0x72/0x450
[<0000000000100020>] _stext+0x20/0x80
If NUMA is selected numa_setup_memory() will fix the node assignments
before the vmemmap will be populated; so this warning will only appear
if NUMA is not selected.
To fix this simply use memblock_add_node() and re-add crash kernel
memory explicitly to node 0.
Reported-and-tested-by: Christian Borntraeger <borntraeger@de.ibm.com>
Fixes: 4e042af463f8 ("s390/kexec: fix crash on resize of reserved memory")
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 5457e03de918f7a3e294eb9d26a608ab8a579976 upstream.
The buffer for iucv_message_receive() needs to be below 2 GB. In
__iucv_message_receive(), the buffer address is casted to an u32, which
would result in either memory corruption or an addressing exception when
using addresses >= 2 GB.
Fix this by using GFP_DMA for the buffer allocation.
Signed-off-by: Gerald Schaefer <gerald.schaefer@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 2e700f8d85975f516ccaad821278c1fe66b2cc98 upstream.
When you use the firmware usermode helper fallback with a timeout value set to a
value greater than INT_MAX (2147483647) a cast overflow issue causes the
timeout value to go negative and breaks all usermode helper loading. This
regression was introduced through commit 68ff2a00dbf5 ("firmware_loader:
handle timeout via wait_for_completion_interruptible_timeout()") on kernel
v4.0.
The firmware_class drivers relies on the firmware usermode helper
fallback as a mechanism to look for firmware if the direct filesystem
search failed only if:
a) You've enabled CONFIG_FW_LOADER_USER_HELPER_FALLBACK (not many distros):
Then all of these callers will rely on the fallback mechanism in case
the firmware is not found through an initial direct filesystem lookup:
o request_firmware()
o request_firmware_into_buf()
o request_firmware_nowait()
b) If you've only enabled CONFIG_FW_LOADER_USER_HELPER (most distros):
Then only callers using request_firmware_nowait() with the second
argument set to false, this explicitly is requesting the UMH firmware
fallback to be relied on in case the first filesystem lookup fails.
Using Coccinelle SmPL grammar we have identified only two drivers
explicitly requesting the UMH firmware fallback mechanism:
- drivers/firmware/dell_rbu.c
- drivers/leds/leds-lp55xx-common.c
Since most distributions only enable CONFIG_FW_LOADER_USER_HELPER the
biggest impact of this regression are users of the dell_rbu and
leds-lp55xx-common device driver which required the UMH to find their
respective needed firmwares.
The default timeout for the UMH is set to 60 seconds always, as of
commit 68ff2a00dbf5 ("firmware_loader: handle timeout via
wait_for_completion_interruptible_timeout()") the timeout was bumped
to MAX_JIFFY_OFFSET ((LONG_MAX >> 1)-1). Additionally the MAX_JIFFY_OFFSET
value was also used if the timeout was configured by a user to 0.
The following works:
echo 2147483647 > /sys/class/firmware/timeout
But both of the following set the timeout to MAX_JIFFY_OFFSET even if
we display 0 back to userspace:
echo 2147483648 > /sys/class/firmware/timeout
cat /sys/class/firmware/timeout
0
echo 0> /sys/class/firmware/timeout
cat /sys/class/firmware/timeout
0
A max value of INT_MAX (2147483647) seconds is therefore implicit due to the
another cast with simple_strtol().
This fixes the secondary cast (the first one is simple_strtol() but its an
issue only by forcing an implicit limit) by re-using the timeout variable and
only setting retval in appropriate cases.
Lastly worth noting systemd had ripped out the UMH firmware fallback
mechanism from udev since udev 2014 via commit be2ea723b1d023b3d
("udev: remove userspace firmware loading support"), so as of systemd v217.
Signed-off-by: Yves-Alexis Perez <corsac@corsac.net>
Fixes: 68ff2a00dbf5 "firmware_loader: handle timeout via wait_for_completion_interruptible_timeout()"
Cc: Luis R. Rodriguez <mcgrof@kernel.org>
Cc: Ming Lei <ming.lei@canonical.com>
Cc: Bjorn Andersson <bjorn.andersson@linaro.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Luis R. Rodriguez <mcgrof@kernel.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
[mcgrof@kernel.org: gave commit log a whole lot of love]
Signed-off-by: Luis R. Rodriguez <mcgrof@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 08fe007968b2b45e831daf74899f79a54d73f773 upstream.
An ARC700 customer reported linux boot crashes when upgrading to bigger
L1 dcache (64K from 32K). Turns out they had an aliasing VIPT config and
current code only assumed 2 colours, while theirs had 4. So default to 4
colours and complain if there are fewer. Ideally this needs to be a
Kconfig option, but heck that's too much of hassle for a single user.
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit d2a145252c52792bc59e4767b486b26c430af4bb upstream.
A race between scanning and fc_remote_port_delete() may result in a
permanent stop if the device gets blocked before scsi_sysfs_add_sdev()
and unblocked after. The reason is that blocking a device sets both the
SDEV_BLOCKED state and the QUEUE_FLAG_STOPPED. However,
scsi_sysfs_add_sdev() unconditionally sets SDEV_RUNNING which causes the
device to be ignored by scsi_target_unblock() and thus never have its
QUEUE_FLAG_STOPPED cleared leading to a device which is apparently
running but has a stopped queue.
We actually have two places where SDEV_RUNNING is set: once in
scsi_add_lun() which respects the blocked flag and once in
scsi_sysfs_add_sdev() which doesn't. Since the second set is entirely
spurious, simply remove it to fix the problem.
Reported-by: Zengxi Chen <chenzengxi@huawei.com>
Signed-off-by: Wei Fang <fangwei1@huawei.com>
Reviewed-by: Ewan D. Milne <emilne@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 6f2ce1c6af37191640ee3ff6e8fc39ea10352f4c upstream.
It is unavoidable that zfcp_scsi_queuecommand() has to finish requests
with DID_IMM_RETRY (like fc_remote_port_chkready()) during the time
window when zfcp detected an unavailable rport but
fc_remote_port_delete(), which is asynchronous via
zfcp_scsi_schedule_rport_block(), has not yet blocked the rport.
However, for the case when the rport becomes available again, we should
prevent unblocking the rport too early. In contrast to other FCP LLDDs,
zfcp has to open each LUN with the FCP channel hardware before it can
send I/O to a LUN. So if a port already has LUNs attached and we
unblock the rport just after port recovery, recoveries of LUNs behind
this port can still be pending which in turn force
zfcp_scsi_queuecommand() to unnecessarily finish requests with
DID_IMM_RETRY.
This also opens a time window with unblocked rport (until the followup
LUN reopen recovery has finished). If a scsi_cmnd timeout occurs during
this time window fc_timed_out() cannot work as desired and such command
would indeed time out and trigger scsi_eh. This prevents a clean and
timely path failover. This should not happen if the path issue can be
recovered on FC transport layer such as path issues involving RSCNs.
Fix this by only calling zfcp_scsi_schedule_rport_register(), to
asynchronously trigger fc_remote_port_add(), after all LUN recoveries as
children of the rport have finished and no new recoveries of equal or
higher order were triggered meanwhile. Finished intentionally includes
any recovery result no matter if successful or failed (still unblock
rport so other successful LUNs work). For simplicity, we check after
each finished LUN recovery if there is another LUN recovery pending on
the same port and then do nothing. We handle the special case of a
successful recovery of a port without LUN children the same way without
changing this case's semantics.
For debugging we introduce 2 new trace records written if the rport
unblock attempt was aborted due to still unfinished or freshly triggered
recovery. The records are only written above the default trace level.
Benjamin noticed the important special case of new recovery that can be
triggered between having given up the erp_lock and before calling
zfcp_erp_action_cleanup() within zfcp_erp_strategy(). We must avoid the
following sequence:
ERP thread rport_work other context
------------------------- -------------- --------------------------------
port is unblocked, rport still blocked,
due to pending/running ERP action,
so ((port->status & ...UNBLOCK) != 0)
and (port->rport == NULL)
unlock ERP
zfcp_erp_action_cleanup()
case ZFCP_ERP_ACTION_REOPEN_LUN:
zfcp_erp_try_rport_unblock()
((status & ...UNBLOCK) != 0) [OLD!]
zfcp_erp_port_reopen()
lock ERP
zfcp_erp_port_block()
port->status clear ...UNBLOCK
unlock ERP
zfcp_scsi_schedule_rport_block()
port->rport_task = RPORT_DEL
queue_work(rport_work)
zfcp_scsi_rport_work()
(port->rport_task != RPORT_ADD)
port->rport_task = RPORT_NONE
zfcp_scsi_rport_block()
if (!port->rport) return
zfcp_scsi_schedule_rport_register()
port->rport_task = RPORT_ADD
queue_work(rport_work)
zfcp_scsi_rport_work()
(port->rport_task == RPORT_ADD)
port->rport_task = RPORT_NONE
zfcp_scsi_rport_register()
(port->rport == NULL)
rport = fc_remote_port_add()
port->rport = rport;
Now the rport was erroneously unblocked while the zfcp_port is blocked.
This is another situation we want to avoid due to scsi_eh
potential. This state would at least remain until the new recovery from
the other context finished successfully, or potentially forever if it
failed. In order to close this race, we take the erp_lock inside
zfcp_erp_try_rport_unblock() when checking the status of zfcp_port or
LUN. With that, the possible corresponding rport state sequences would
be: (unblock[ERP thread],block[other context]) if the ERP thread gets
erp_lock first and still sees ((port->status & ...UNBLOCK) != 0),
(block[other context],NOP[ERP thread]) if the ERP thread gets erp_lock
after the other context has already cleard ...UNBLOCK from port->status.
Since checking fields of struct erp_action is unsafe because they could
have been overwritten (re-used for new recovery) meanwhile, we only
check status of zfcp_port and LUN since these are only changed under
erp_lock elsewhere. Regarding the check of the proper status flags (port
or port_forced are similar to the shown adapter recovery):
[zfcp_erp_adapter_shutdown()]
zfcp_erp_adapter_reopen()
zfcp_erp_adapter_block()
* clear UNBLOCK ---------------------------------------+
zfcp_scsi_schedule_rports_block() |
write_lock_irqsave(&adapter->erp_lock, flags);-------+ |
zfcp_erp_action_enqueue() | |
zfcp_erp_setup_act() | |
* set ERP_INUSE -----------------------------------|--|--+
write_unlock_irqrestore(&adapter->erp_lock, flags);--+ | |
.context-switch. | |
zfcp_erp_thread() | |
zfcp_erp_strategy() | |
write_lock_irqsave(&adapter->erp_lock, flags);------+ | |
... | | |
zfcp_erp_strategy_check_target() | | |
zfcp_erp_strategy_check_adapter() | | |
zfcp_erp_adapter_unblock() | | |
* set UNBLOCK -----------------------------------|--+ |
zfcp_erp_action_dequeue() | |
* clear ERP_INUSE ---------------------------------|-----+
... |
write_unlock_irqrestore(&adapter->erp_lock, flags);-+
Hence, we should check for both UNBLOCK and ERP_INUSE because they are
interleaved. Also we need to explicitly check ERP_FAILED for the link
down case which currently does not clear the UNBLOCK flag in
zfcp_fsf_link_down_info_eval().
Signed-off-by: Steffen Maier <maier@linux.vnet.ibm.com>
Fixes: 8830271c4819 ("[SCSI] zfcp: Dont fail SCSI commands when transitioning to blocked fc_rport")
Fixes: a2fa0aede07c ("[SCSI] zfcp: Block FC transport rports early on errors")
Fixes: 5f852be9e11d ("[SCSI] zfcp: Fix deadlock between zfcp ERP and SCSI")
Fixes: 338151e06608 ("[SCSI] zfcp: make use of fc_remote_port_delete when target port is unavailable")
Fixes: 3859f6a248cb ("[PATCH] zfcp: add rports to enable scsi_add_device to work again")
Reviewed-by: Benjamin Block <bblock@linux.vnet.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 56d23ed7adf3974f10e91b643bd230e9c65b5f79 upstream.
Since quite a while, Linux issues enough SCSI commands per scsi_device
which successfully return with FCP_RESID_UNDER, FSF_FCP_RSP_AVAILABLE,
and SAM_STAT_GOOD. This floods the HBA trace area and we cannot see
other and important HBA trace records long enough.
Therefore, do not trace HBA response errors for pure benign residual
under counts at the default trace level.
This excludes benign residual under count combined with other validity
bits set in FCP_RSP_IU, such as FCP_SNS_LEN_VAL. For all those other
cases, we still do want to see both the HBA record and the corresponding
SCSI record by default.
Signed-off-by: Steffen Maier <maier@linux.vnet.ibm.com>
Fixes: a54ca0f62f95 ("[SCSI] zfcp: Redesign of the debug tracing for HBA records.")
Reviewed-by: Benjamin Block <bblock@linux.vnet.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit dac37e15b7d511e026a9313c8c46794c144103cd upstream.
When SCSI EH invokes zFCP's callbacks for eh_device_reset_handler() and
eh_target_reset_handler(), it expects us to relent the ownership over
the given scsi_cmnd and all other scsi_cmnds within the same scope - LUN
or target - when returning with SUCCESS from the callback ('release'
them). SCSI EH can then reuse those commands.
We did not follow this rule to release commands upon SUCCESS; and if
later a reply arrived for one of those supposed to be released commands,
we would still make use of the scsi_cmnd in our ingress tasklet. This
will at least result in undefined behavior or a kernel panic because of
a wrong kernel pointer dereference.
To fix this, we NULLify all pointers to scsi_cmnds (struct zfcp_fsf_req
*)->data in the matching scope if a TMF was successful. This is done
under the locks (struct zfcp_adapter *)->abort_lock and (struct
zfcp_reqlist *)->lock to prevent the requests from being removed from
the request-hashtable, and the ingress tasklet from making use of the
scsi_cmnd-pointer in zfcp_fsf_fcp_cmnd_handler().
For cases where a reply arrives during SCSI EH, but before we get a
chance to NULLify the pointer - but before we return from the callback
-, we assume that the code is protected from races via the CAS operation
in blk_complete_request() that is called in scsi_done().
The following stacktrace shows an example for a crash resulting from the
previous behavior:
Unable to handle kernel pointer dereference at virtual kernel address fffffee17a672000
Oops: 0038 [#1] SMP
CPU: 2 PID: 0 Comm: swapper/2 Not tainted
task: 00000003f7ff5be0 ti: 00000003f3d38000 task.ti: 00000003f3d38000
Krnl PSW : 0404d00180000000 00000000001156b0 (smp_vcpu_scheduled+0x18/0x40)
R:0 T:1 IO:0 EX:0 Key:0 M:1 W:0 P:0 AS:3 CC:1 PM:0 EA:3
Krnl GPRS: 000000200000007e 0000000000000000 fffffee17a671fd8 0000000300000015
ffffffff80000000 00000000005dfde8 07000003f7f80e00 000000004fa4e800
000000036ce8d8f8 000000036ce8d9c0 00000003ece8fe00 ffffffff969c9e93
00000003fffffffd 000000036ce8da10 00000000003bf134 00000003f3b07918
Krnl Code: 00000000001156a2: a7190000 lghi %r1,0
00000000001156a6: a7380015 lhi %r3,21
#00000000001156aa: e32050000008 ag %r2,0(%r5)
>00000000001156b0: 482022b0 lh %r2,688(%r2)
00000000001156b4: ae123000 sigp %r1,%r2,0(%r3)
00000000001156b8: b2220020 ipm %r2
00000000001156bc: 8820001c srl %r2,28
00000000001156c0: c02700000001 xilf %r2,1
Call Trace:
([<0000000000000000>] 0x0)
[<000003ff807bdb8e>] zfcp_fsf_fcp_cmnd_handler+0x3de/0x490 [zfcp]
[<000003ff807be30a>] zfcp_fsf_req_complete+0x252/0x800 [zfcp]
[<000003ff807c0a48>] zfcp_fsf_reqid_check+0xe8/0x190 [zfcp]
[<000003ff807c194e>] zfcp_qdio_int_resp+0x66/0x188 [zfcp]
[<000003ff80440c64>] qdio_kick_handler+0xdc/0x310 [qdio]
[<000003ff804463d0>] __tiqdio_inbound_processing+0xf8/0xcd8 [qdio]
[<0000000000141fd4>] tasklet_action+0x9c/0x170
[<0000000000141550>] __do_softirq+0xe8/0x258
[<000000000010ce0a>] do_softirq+0xba/0xc0
[<000000000014187c>] irq_exit+0xc4/0xe8
[<000000000046b526>] do_IRQ+0x146/0x1d8
[<00000000005d6a3c>] io_return+0x0/0x8
[<00000000005d6422>] vtime_stop_cpu+0x4a/0xa0
([<0000000000000000>] 0x0)
[<0000000000103d8a>] arch_cpu_idle+0xa2/0xb0
[<0000000000197f94>] cpu_startup_entry+0x13c/0x1f8
[<0000000000114782>] smp_start_secondary+0xda/0xe8
[<00000000005d6efe>] restart_int_handler+0x56/0x6c
[<0000000000000000>] 0x0
Last Breaking-Event-Address:
[<00000000003bf12e>] arch_spin_lock_wait+0x56/0xb0
Suggested-by: Steffen Maier <maier@linux.vnet.ibm.com>
Signed-off-by: Benjamin Block <bblock@linux.vnet.ibm.com>
Fixes: ea127f9754 ("[PATCH] s390 (7/7): zfcp host adapter.") (tglx/history.git)
Signed-off-by: Steffen Maier <maier@linux.vnet.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 83337e544323a8bd7492994d64af339175ac7107 upstream.
If iscsit_tpg_add_network_portal() fails then
return error code instead of 0 to user space.
If iscsi-target returns 0 then user space keeps
on retrying same command infinitely, targetcli or
echo hangs till command completes with non zero
return value. In some cases it is possible that
add network portal command never completes with
success even after retrying multiple times,
for example - cxgbit_setup_np() always returns
-EINVAL if portal IP does not belong to Chelsio
adapter interface.
Signed-off-by: Varun Prakash <varun@chelsio.com>
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
[ bvanassche: Added "Fixes:" and "Cc: stable" tags ]
Fixes: commit d4b3fa4b0881 ("iscsi-target: Make iscsi_tpg_np driver show/store use generic code")
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
does not support JBOD sequence map
commit d5573584429254a14708cf8375c47092b5edaf2c upstream.
Signed-off-by: Sumit Saxena <sumit.saxena@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
30secs before reset
commit 18e1c7f68a5814442abad849abe6eacbf02ffd7c upstream.
For SRIOV enabled firmware, if there is a OCR(online controller reset)
possibility driver set the convert flag to 1, which is not happening if
there are outstanding commands even after 180 seconds. As driver does
not set convert flag to 1 and still making the OCR to run, VF(Virtual
function) driver is directly writing on to the register instead of
waiting for 30 seconds. Setting convert flag to 1 will cause VF driver
will wait for 30 secs before going for reset.
Signed-off-by: Kiran Kumar Kasturi <kiran-kumar.kasturi@broadcom.com>
Signed-off-by: Sumit Saxena <sumit.saxena@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit a0ebf519b8a2666438d999c62995618c710573e5 upstream.
Make sure to drop the reference taken by class_find_device() also on
allocation errors in open().
Signed-off-by: Johan Hovold <johan@kernel.org>
Fixes: 7bd1d4093c2f ("stm class: Introduce an abstraction for...")
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
