| Age | Commit message (Collapse) | Author |
|---|
|
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media
Pull media fixes from Mauro Carvalho Chehab:
- several fixes for new drivers added for Kernel 4.8 addition (cec
core, pulse8 cec driver and Mediatek vcodec)
- a regression fix for cx23885 and saa7134 drivers
- an important fix for rcar-fcp, making rcar_fcp_enable() return 0 on
success
* tag 'media/v4.8-7' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (25 commits)
[media] cx23885/saa7134: assign q->dev to the PCI device
[media] rcar-fcp: Make sure rcar_fcp_enable() returns 0 on success
[media] cec: fix ioctl return code when not registered
[media] cec: don't Feature Abort broadcast msgs when unregistered
[media] vcodec:mediatek: Refine VP8 encoder driver
[media] vcodec:mediatek: Refine H264 encoder driver
[media] vcodec:mediatek: change H264 profile default to profile high
[media] vcodec:mediatek: Add timestamp and timecode copy for V4L2 Encoder
[media] vcodec:mediatek: Fix visible_height larger than coded_height issue in s_fmt_out
[media] vcodec:mediatek: Fix fops_vcodec_release flow for V4L2 Encoder
[media] vcodec:mediatek:code refine for v4l2 Encoder driver
[media] cec-funcs.h: add missing vendor-specific messages
[media] cec-edid: check for IEEE identifier
[media] pulse8-cec: fix error handling
[media] pulse8-cec: set correct Signal Free Time
[media] mtk-vcodec: add HAS_DMA dependency
[media] cec: ignore messages when log_addr_mask == 0
[media] cec: add item to TODO
[media] cec: set unclaimed addresses to CEC_LOG_ADDR_INVALID
[media] cec: add CEC_LOG_ADDRS_FL_ALLOW_UNREG_FALLBACK flag
...
|
|
Pull networking fixes from David Miller:
"Mostly small bits scattered all over the place, which is usually how
things go this late in the -rc series.
1) Proper driver init device resets in bnx2, from Baoquan He.
2) Fix accounting overflow in __tcp_retransmit_skb(),
sk_forward_alloc, and ip_idents_reserve, from Eric Dumazet.
3) Fix crash in bna driver ethtool stats handling, from Ivan Vecera.
4) Missing check of skb_linearize() return value in mac80211, from
Johannes Berg.
5) Endianness fix in nf_table_trace dumps, from Liping Zhang.
6) SSN comparison fix in SCTP, from Marcelo Ricardo Leitner.
7) Update DSA and b44 MAINTAINERS entries.
8) Make input path of vti6 driver work again, from Nicolas Dichtel.
9) Off-by-one in mlx4, from Sebastian Ott.
10) Fix fallback route lookup handling in ipv6, from Vincent Bernat.
11) Fix stack corruption on probe in qed driver, from Yuval Mintz.
12) PHY init fixes in r8152 from Hayes Wang.
13) Missing SKB free in irda_accept error path, from Phil Turnbull"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (61 commits)
tcp: properly account Fast Open SYN-ACK retrans
tcp: fix under-accounting retransmit SNMP counters
MAINTAINERS: Update b44 maintainer.
net: get rid of an signed integer overflow in ip_idents_reserve()
net/mlx4_core: Fix to clean devlink resources
net: can: ifi: Configure transmitter delay
vti6: fix input path
ipmr, ip6mr: return lastuse relative to now
r8152: disable ALDPS and EEE before setting PHY
r8152: remove r8153_enable_eee
r8152: move PHY settings to hw_phy_cfg
r8152: move enabling PHY
r8152: move some functions
cxgb4/cxgb4vf: Allocate more queues for 25G and 100G adapter
qed: Fix stack corruption on probe
MAINTAINERS: Add an entry for the core network DSA code
net: ipv6: fallback to full lookup if table lookup is unsuitable
net/mlx5: E-Switch, Handle mode change failures
net/mlx5: E-Switch, Fix error flow in the SRIOV e-switch init code
net/mlx5: Fix flow counter bulk command out mailbox allocation
...
|
|
Instead of open coding it use the threaded irq mechanism in
xen-netback.
Signed-off-by: Juergen Gross <jgross@suse.com>
Acked-by: Wei Liu <wei.liu2@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Potential dangerous invalid pointer might be accessed if
the error happens when couple phy_device to net_device so
cleanup the error path.
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
1) use new api [get|set]_link_ksettings instead
of [get|set]_settings old ones.
2) dev->phydev is sure being ready before calling
these callbacks, so removing all the sanity check
if it is existing.
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
remove the unused variable for parsing PHY address
and the related logic for sanity test which would
be all already handled done when of_mdiobus_register
was called
Reported-by: Nelson Chang <nelson.chang@mediatek.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
reuse phydev already in struct net_device instead of creating
another new one in private structure.
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Sean Wang says:
====================
mediatek: add support for RGMII on GMAC0 through TRGMII hardware module
By default, GMAC0 is connected to built-in switch called
MT7530 through the proprietary interface called Turbo RGMII
(TRGMII). TRGMII also supports well for RGMII as generic external
PHY uses but requires some slight changes to the setup of TRGMII
and doesn't have well support on current driver.
So this patchset
1) provides the slight changes of the setup for RGMII can work
through TRGMII
2) adds additional setting "trgmii" as PHY_INTERFACE_MODE_TRGMII
about phy-mode on device tree to make GMAC0 distinguish which
mode it runs
3) changes dynamically source clock, TX/RX delay and interface
mode on TRGMII for adapting various link
Changes since v1:
- fixed the style of comment which doesn't have a space at
the beginning and end of comment lines
- add support for phy-mode "trgmii" as PHY_INTERFACE_MODE_TRGMII
into linux/phy.h
- enhance the Documentation about device tree binding for trgmii
which is applicable only for GMAC0 which uses fixed-link
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
GMAC0
Add the dts property for the capability if TRGMII supported on GAMC0
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
through TRGMII
Changing dynamically source clock, TX/RX delay and interface mode
used by TRGMII hardware module inside PHY capability polling routine
for adapting to the various speed of RGMII used by external PHY for
GMAC0.
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
adds PHY-mode "trgmii" as an extension for the operation
mode of the PHY interface for PHY_INTERFACE_MODE_TRGMII.
and adds a variable trgmii inside mtk_mac as the indication
to make the difference between the MAC connected to internal
switch or connected to external PHY by the given configuration
on the board and then to perform the corresponding setup on
TRGMII hardware module.
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/dhowells/linux-fs
David Howells says:
====================
rxrpc: Preparation for slow-start algorithm [ver #2]
Here are some patches that prepare for improvements in ACK generation and
for the implementation of the slow-start part of the protocol:
(1) Stop storing the protocol header in the Tx socket buffers, but rather
generate it on the fly. This potentially saves a little space and
makes it easier to alter the header just before transmission (the
flags may get altered and the serial number has to be changed).
(2) Mask off the Tx buffer annotations and add a flag to record which ones
have already been resent.
(3) Track RTT on a per-peer basis for use in future changes. Tracepoints
are added to log this.
(4) Send PING ACKs in response to incoming calls to elicit a PING-RESPONSE
ACK from which RTT data can be calculated. The response also carries
other useful information.
(5) Expedite PING-RESPONSE ACK generation from sendmsg. If we're actively
using sendmsg, this allows us, under some circumstances, to avoid
having to rely on the background work item to run to generate this
ACK.
This requires ktime_sub_ms() to be added.
(6) Set the REQUEST-ACK flag on some DATA packets to elicit ACK-REQUESTED
ACKs from which RTT data can be calculated.
(7) Limit the use of pings and ACK requests for RTT determination.
Changes:
(V2) Don't use the C division operator for 64-bit division. One instance
should use do_div() and the other should be using nsecs_to_jiffies().
The last two patches got transposed, leading to an undefined symbol
in one of them.
Reported-by: kbuild test robot <lkp@intel.com>
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We don't want to send a PING ACK for every new incoming call as that just
adds to the network traffic. Instead, we send a PING ACK to the first
three that we receive and then once per second thereafter.
This could probably be made adjustable in future.
Signed-off-by: David Howells <dhowells@redhat.com>
|
|
Reduce the number of ACK-Requests we set on DATA packets that we're sending
to reduce network traffic. We set the flag on odd-numbered DATA packets to
start off the RTT cache until we have at least three entries in it and then
probe once per second thereafter to keep it topped up.
This could be made tunable in future.
Note that from this point, the RXRPC_REQUEST_ACK flag is set on DATA
packets as we transmit them and not stored statically in the sk_buff.
Signed-off-by: David Howells <dhowells@redhat.com>
|
|
Since the TFO socket is accepted right off SYN-data, the socket
owner can call getsockopt(TCP_INFO) to collect ongoing SYN-ACK
retransmission or timeout stats (i.e., tcpi_total_retrans,
tcpi_retransmits). Currently those stats are only updated
upon handshake completes. This patch fixes it.
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: Soheil Hassas Yeganeh <soheil@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch fixes these under-accounting SNMP rtx stats
LINUX_MIB_TCPFORWARDRETRANS
LINUX_MIB_TCPFASTRETRANS
LINUX_MIB_TCPSLOWSTARTRETRANS
when retransmitting TSO packets
Fixes: 10d3be569243 ("tcp-tso: do not split TSO packets at retransmit time")
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Joel Stanley says:
====================
ftgmac100 support for ast2500
This series adds support to the ftgmac100 driver for the Aspeed ast2400 and
ast2500 SoCs. In particular, they ensure the driver works correctly on the
ast2500 where the MAC block has seen some changes in register layout.
They have been tested on ast2400 and ast2500 systems with the NCSI stack and
with a directly attached PHY.
V2 reworks the two patches relating to PHYSTS_CHG into the one patch that
disables the interrupt instead of playing with interrupt sensitivity. I kept
patch 4 'net/faraday: Clear stale interrupts' which was first introduced to
clear the stale PHYSTS_CHG interrupt, as it helps keep us safe from unhygienic
(vendor) bootloaders.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The PHYSTS_CHG (the ftgmac100's PHY IRQ) is telling the system to go
look at the PHY registers for a link status change.
The interrupt was causing issues on Aspeed SoC where some board designs
had an active high configuration, some active low, and in some cases
repurposed for other functions. When misconfigured Linux would chew 100%
of CPU cycles servicing interrupts:
[ 20.280000] ftgmac100 1e660000.ethernet eth0: [ISR] = 0x200: PHYSTS_CHG
[ 20.280000] ftgmac100 1e660000.ethernet eth0: [ISR] = 0x200: PHYSTS_CHG
[ 20.280000] ftgmac100 1e660000.ethernet eth0: [ISR] = 0x200: PHYSTS_CHG
[ 20.300000] ftgmac100 1e660000.ethernet eth0: [ISR] = 0x200: PHYSTS_CHG
While in the ftgmac100 IP can be configured for high, low and edge
sensitivity the current driver always polls the PHY, so we chose to mask
out the interrupt.
See https://patchwork.ozlabs.org/patch/672099/ for more discussion.
Signed-off-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The Aspeed SoCs have a new MDIO interface as an option in the G4 and G5
SoCs. The old one is still available, so select it in order to remain
compatible with the ftgmac100 driver.
Signed-off-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
There is stale interrupt (PHYSTS_CHG in ISR, bit#6 in 0x0) from
the bootloader (uboot) when enabling the MAC. The stale interrupts
aren't part of kernel and should be cleared.
This clears the stale interrupts in ISR (0x0) when enabling the MAC.
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The RXDES and TXDES registers bits in the ftgmac100 indicates EDO{R,T}R
at bit position 15 for the Faraday Tech IP. However, the version of this
IP present in the Aspeed SoCs has these bits at position 30 in the
registers.
It appers that ast2400 SoCs support both positions, with the 15th bit
marked as reserved but still functional. In the ast2500 this bit is
reused for another function, so we need a work around.
This was confirmed with engineers from Aspeed that using bit 30 is
correct for both the ast2400 and ast2500 SoCs.
Signed-off-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
These bits are #defined at a fixed location. In order to support future
hardware that has chosen to move these bits around move the bits into a
member of the struct ftgmac100.
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The ftgmac100 hardware revision in e.g. the Aspeed AST2500 no longer
reserves all bits in RXDES#2 but instead uses the bottom 16 bits to
store MAC frame metadata. Avoid corruption by shifting struct page
pointers out to their own member in struct ftgmac100.
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In addition to sending a PING ACK to gain RTT data, we can set the
RXRPC_REQUEST_ACK flag on a DATA packet and get a REQUESTED-ACK ACK. The
ACK packet contains the serial number of the packet it is in response to,
so we can look through the Tx buffer for a matching DATA packet.
This requires that the data packets be stamped with the time of
transmission as a ktime rather than having the resend_at time in jiffies.
This further requires the resend code to do the resend determination in
ktimes and convert to jiffies to set the timer.
Signed-off-by: David Howells <dhowells@redhat.com>
|
|
Add a ktime_sub_ms() to go with ktime_add_ms() and co. for use in AF_RXRPC
RTT determination.
Signed-off-by: David Howells <dhowells@redhat.com>
|
|
Expedite the transmission of a response to a PING ACK by sending it from
sendmsg if one is pending. We're most likely to see a PING ACK during the
client call Tx phase as the other side may use it to determine a number of
parameters, such as the client's receive window size, the RTT and whether
the client is doing slow start (similar to RFC5681).
If we don't expedite it, it's left to the background processing thread to
transmit.
Signed-off-by: David Howells <dhowells@redhat.com>
|
|
Send a PING ACK packet to the peer when we get a new incoming call from a
peer we don't have a record for. The PING RESPONSE ACK packet will tell us
the following about the peer:
(1) its receive window size
(2) its MTU sizes
(3) its support for jumbo DATA packets
(4) if it supports slow start (similar to RFC 5681)
(5) an estimate of the RTT
This is necessary because the peer won't normally send us an ACK until it
gets to the Rx phase and we send it a packet, but we would like to know
some of this information before we start sending packets.
A pair of tracepoints are added so that RTT determination can be observed.
Signed-off-by: David Howells <dhowells@redhat.com>
|
|
Remove an open coded simple_open() function and replace file
operations references to the function with simple_open()
instead.
Generated by: scripts/coccinelle/api/simple_open.cocci
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
mdio_module_driver() makes the code simpler by eliminating
boilerplate code.
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Fixes the following sparse warning:
drivers/net/dsa/qca8k.c:259:22: warning:
symbol 'qca8k_regmap_config' was not declared. Should it be static?
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Marcelo Ricardo Leitner says:
====================
Rename WORD_TRUNC/ROUND macros and use them
This patchset aims to rename these macros to a non-confusing name, as
reported by David Laight and David Miller, and to update all remaining
places to make use of it, which was 1 last remaining spot.
v3:
- Name it SCTP_PAD4 instead of SCTP_ALIGN4, as suggested by David Laight
v2:
- fixed 2nd patch summary
Details on the specific changelogs.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
And avoid the usage of '&~3'. This is the last place still not using
the macro.
Also break the line to make it easier to read.
Signed-off-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
To something more meaningful these days, specially because this is
working on packet headers or lengths and which are not tied to any CPU
arch but to the protocol itself.
So, WORD_TRUNC becomes SCTP_TRUNC4 and WORD_ROUND becomes SCTP_PAD4.
Reported-by: David Laight <David.Laight@ACULAB.COM>
Reported-by: David Miller <davem@davemloft.net>
Signed-off-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/klassert/ipsec
Steffen Klassert says:
====================
pull request (net): ipsec 2016-09-21
1) Propagate errors on security context allocation.
From Mathias Krause.
2) Fix inbound policy checks for inter address family tunnels.
From Thomas Zeitlhofer.
3) Fix an old memory leak on aead algorithm usage.
From Ilan Tayari.
4) A recent patch fixed a possible NULL pointer dereference
but broke the vti6 input path.
Fix from Nicolas Dichtel.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Tariq Toukan says:
====================
mlx5e XDP support
This series adds XDP support in mlx5e driver.
This includes the use cases: XDP_DROP, XDP_PASS, and XDP_TX.
Single stream performance tests show 16.5 Mpps for XDP_DROP,
and 12.4 Mpps for XDP_TX, with nice scalability for multiple streams/rings.
This rate of XDP_DROP is lower than the 32 Mpps we got in previous
implementation, when Striding RQ was used.
We moved to non-Striding RQ, as some XDP_TX requirements (like headroom,
packet-per-page) cannot be satisfied with the current Striding RQ HW,
and we decided to fully support both DROP/TX.
Few directions are considered in order to enable the faster rate for XDP_DROP,
e.g a possibility for users to enable Striding RQ so they choose optimized
XDP_DROP on the price of partial XDP_TX functionality, or some HW changes.
Series generated against net-next commit:
cf714ac147e0 'ipvlan: Fix dependency issue'
Thanks,
Tariq
V2:
* patch 8:
- when XDP_TX fails, call mlx5e_page_release and drop the packet.
- update xdp_tx counter within mlx5e_xmit_xdp_frame.
(mlx5e_xmit_xdp_frame return value becomes obsolete, change it to void)
- drop the packet for unknown XDP return code.
* patch 9:
- use a boolean for xdp_doorbell in SQ struct, instead of dragging it
throughout the functions calls.
- handle doorbell and counters within mlx5e_xmit_xdp_frame.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Previously we rang XDP SQ doorbell on every forwarded XDP packet.
Here we introduce a xmit more like mechanism that will queue up more
than one packet into SQ (up to RX napi budget) w/o notifying the hardware.
Once RX napi budget is consumed and we exit napi RX loop, we will
flush (doorbell) all XDP looped packets in case there are such.
XDP forward packet rate:
Comparing XDP with and w/o xmit more (bulk transmit):
RX Cores XDP TX XDP TX (xmit more)
---------------------------------------------------
1 6.5Mpps 12.4Mpps
2 13.2Mpps 24.2Mpps
4 25.2Mpps 36.3Mpps*
8 36.3Mpps* 36.3Mpps*
*My xmitter was limited to 36.3Mpps, so it is the bottleneck.
It seems that receive side can handle more.
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Adding support for XDP_TX forwarding from xdp program.
Using XDP, now user can loop packets out of the same port.
We create a dedicated TX SQ for each channel that will serve
XDP programs that return XDP_TX action to loop packets back to
the wire directly from the channel RQ RX path.
For that RX pages will now need to be mapped bi-directionally,
and on XDP_TX action we will sync the page back to device then
queue it into SQ for transmission. The XDP xmit frame function will
report back to the RX path if the page was consumed (transmitted), if so,
RX path will forget about that page as if it were released to the stack.
Later on, on XDP TX completion, the page will be released back to the
page cache.
For simplicity this patch will hit a doorbell on every XDP TX packet.
Next patch will introduce a xmit more like mechanism that will
queue up more than one packet into SQ w/o notifying the hardware,
once RX napi loop is done we will hit doorbell once for all XDP TX
packets form the previous loop. This should drastically improve
XDP TX performance.
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Make a clear separate between Regular SQ (TXQ) and ICO SQ creation,
destruction and union their mutual information structures.
Don't allocate redundant TXQ skb/wqe_info/dma_fifo arrays for ICO SQ.
And have a different SQ edge for ICO SQ than TXQ SQ, to be more
accurate.
In preparation for XDP TX support.
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add support for the BPF_PROG_TYPE_PHYS_DEV hook in mlx5e driver.
When XDP is on we make sure to change channels RQs type to
MLX5_WQ_TYPE_LINKED_LIST rather than "striding RQ" type to
ensure "page per packet".
On XDP set, we fail if HW LRO is set and request from user to turn it
off. Since on ConnectX4-LX HW LRO is always on by default, this will be
annoying, but we prefer not to enforce LRO off from XDP set function.
Full channels reset (close/open) is required only when setting XDP
on/off.
When XDP set is called just to exchange programs, we will update
each RQ xdp program on the fly and for synchronization with current
data path RX activity of that RQ, we temporally disable that RQ and
ensure RX path is not running, quickly update and re-enable that RQ,
for that we do:
- rq.state = disabled
- napi_synnchronize
- xchg(rq->xdp_prg)
- rq.state = enabled
- napi_schedule // Just in case we've missed an IRQ
Packet rate performance testing was done with pktgen 64B packets and on
TX side and, TC drop action on RX side compared to XDP fast drop.
CPU: Intel(R) Xeon(R) CPU E5-2680 v3 @ 2.50GHz
Comparison is done between:
1. Baseline, Before this patch with TC drop action
2. This patch with TC drop action
3. This patch with XDP RX fast drop
RX Cores Baseline(TC drop) TC drop XDP fast Drop
--------------------------------------------------------------
1 5.3Mpps 5.3Mpps 16.5Mpps
2 10.2Mpps 10.2Mpps 31.3Mpps
4 20.5Mpps 19.9Mpps 36.3Mpps*
*My xmitter was limited to 36.3Mpps, so it is the bottleneck.
It seems that receive side can handle more.
Signed-off-by: Rana Shahout <ranas@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add two helper functions to allow dynamic changes of RQ type.
mlx5e_set_rq_priv_params and mlx5e_set_rq_type_params will be
used on netdev creation to determine the default RQ type.
This will be needed later for downstream patches of XDP support.
When enabling XDP we will dynamically move from striding RQ to
linked list RQ type.
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Before this patch LRO size was 64K, now with build_skb requires
extra room, headroom + sizeof(skb_shared_info) added to the data
buffer will make wqe size or page_frag_size slightly larger than
64K which will demand order 5 page instead of order 4 in 4K page systems.
We take those extra bytes from hardware LRO data size in order to not
increase the required page order for when hardware LRO is enabled.
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We have two types of RX RQs, and they use two separate sets of
info arrays and structures in RX data path function. Today those
structures are mutually exclusive per RQ type, hence one kind is
allocated on RQ creation according to the RQ type.
For better cache locality and to minimalize the
sizeof(struct mlx5e_rq), in this patch we define them as a union.
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
For non-striding RQ configuration before this patch we had a ring
with pre-allocated SKBs and mapped the SKB->data buffers for
device.
For robustness and better RX data buffers management, we allocate a
page per packet and build_skb around it.
This patch (which is a prerequisite for XDP) will actually reduce
performance for normal stack usage, because we are now hitting a bottleneck
in the page allocator. We use the page-cache to restore or even improve
performance in comparison to the old RX scheme.
Packet rate performance testing was done with pktgen 64B packets on xmit
side and TC ingress dropping action on RX side.
CPU: Intel(R) Xeon(R) CPU E5-2680 v3 @ 2.50GHz
Comparison is done between:
1.Baseline, before 'net/mlx5e: Build RX SKB on demand'
2.Build SKB with RX page cache (This patch)
RX Cores Baseline Build SKB+page-cache Improvement
-----------------------------------------------------------
1 4.16Mpps 5.33Mpps 28%
2 7.16Mpps 10.24Mpps 43%
4 13.61Mpps 20.51Mpps 51%
8 25.32Mpps 32.00Mpps 26%
All respective cores were 100% utilized.
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can
Marc Kleine-Budde says:
====================
pull-request: can 2016-09-21
this is another pull request of one patch for the upcoming linux-4.8 release.
Marek Vasut fixes the CAN-FD bit rate switch in the ifi driver by configuring
the transmitter delay.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We saw sch_fq drops caused by the per flow limit of 100 packets and TCP
when dealing with large cwnd and bursts of retransmits.
Even after increasing the limit to 1000, and even after commit
10d3be569243 ("tcp-tso: do not split TSO packets at retransmit time"),
we can still have these drops.
Under certain conditions, TCP can spend a considerable amount of
time queuing thousands of skbs in a single tcp_xmit_retransmit_queue()
invocation, incurring latency spikes and stalls of other softirq
handlers.
This patch implements TSQ for retransmits, limiting number of packets
and giving more chance for scheduling packets in both ways.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Taking over as maintainer since Gary Zambrano is no longer working
for Broadcom.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Jiri Pirko reported an UBSAN warning happening in ip_idents_reserve()
[] UBSAN: Undefined behaviour in ./arch/x86/include/asm/atomic.h:156:11
[] signed integer overflow:
[] -2117905507 + -695755206 cannot be represented in type 'int'
Since we do not have uatomic_add_return() yet, use atomic_cmpxchg()
so that the arithmetics can be done using unsigned int.
Fixes: 04ca6973f7c1 ("ip: make IP identifiers less predictable")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Andrew Lunn says:
====================
Preparation for mv88e6390
These two patches are a couple of preparation steps for supporting the
the MV88E6390 family of chips. This is a new generation from Marvell,
and will need more feature flags than are currently available in an
unsigned long. Expand to an unsigned long long. The MV88E6390 also
places its port registers somewhere else, so add a wrapper around port
register access.
v2:
Rework wrappers to use mv88e6xxx_{read|write}
Simpliy some (err < ) to (err)
Add Reviewed by tag.
v3::
reg = reg & foo -> reg &= foo
Fix over zealous s/ret/err
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We are soon going to run out of flag bits on 32bit systems. Convert to
unsigned long long.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
