| Age | Commit message (Collapse) | Author |
|---|
|
Currently the offset parameter for skb_copy_bits is changed in
sk_load_word() and sk_load_half(). Therefore it is not correct when
calling skb_copy_bits(). Fix this and use the original offset
for the function call.
Signed-off-by: Michael Holzheu <holzheu@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
|
|
The skb_copy_bits() function has the following signature:
int skb_copy_bits(const struct sk_buff *skb, int offset, void *to, int len)
Currently in bpf_jit.S the "to" and "len" parameters have been
exchanged. So fix this and call the function with the correct
parameters.
Signed-off-by: Michael Holzheu <holzheu@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
|
|
Currently the signed COMPARE HALFWORD IMMEDIATE (chi) and COMPARE (c)
instructions are used to compare "A" with "K". This is not correct
because "A" and "K" are both unsigned. To fix this remove the
chi instruction (no unsigned analogon available) and use the
unsigned COMPARE LOGICAL (cl) instruction instead of COMPARE (c).
Signed-off-by: Michael Holzheu <holzheu@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rzhang/linux
Pull thermal fixes from Zhang Rui:
"Specifics:
- bogus type qualifier fix in OF thermal code.
- Minor fixes on imx and rcar thermal drivers.
- Update TI SoC thermal maintainer entry.
- Updated documentation of OF cpufreq cooling register"
* 'thermal-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/rzhang/linux:
thermal: rcar: Spelling/grammar: s/drier use .../driver uses ...s/
thermal: rcar: change type of ctemp in rcar_thermal_update_temp()
thermal: rcar: fix ENR register value
Documentation: thermal: document of_cpufreq_cooling_register()
Thermal: imx: add clk disable/enable for suspend/resume
MAINTAINERS: update ti-soc-thermal status
MAINTAINERS: Add linux-omap to list of reviewers for TI Thermal
thermal: of: Remove bogus type qualifier for of_thermal_get_trip_points()
|
|
Pull networking fixes from David Miller:
1) Don't use uninitialized data in IPVS, from Dan Carpenter.
2) conntrack race fixes from Pablo Neira Ayuso.
3) Fix TX hangs with i40e, from Jesse Brandeburg.
4) Fix budget return from poll calls in dnet and alx, from Eric
Dumazet.
5) Fix bugus "if (unlikely(x) < 0)" test in AF_PACKET, from Christoph
Jaeger.
6) Fix bug introduced by conversion to list_head in TIPC retransmit
code, from Jon Paul Maloy.
7) Don't use GFP_NOIO under spinlock in USB kaweth driver, from Alexey
Khoroshilov.
8) Fix bridge build with INET disabled, from Arnd Bergmann.
9) Fix netlink array overrun for PROBE attributes in openvswitch, from
Thomas Graf.
10) Don't hold spinlock across synchronize_irq() in tg3 driver, from
Prashant Sreedharan.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (44 commits)
tg3: Release tp->lock before invoking synchronize_irq()
tg3: tg3_reset_task() needs to use rtnl_lock to synchronize
tg3: tg3_timer() should grab tp->lock before checking for tp->irq_sync
team: avoid possible underflow of count_pending value for notify_peers and mcast_rejoin
openvswitch: packet messages need their own probe attribtue
i40e: adds FCoE configure option
cxgb4vf: Fix queue allocation for 40G adapter
netdevice: Add missing parentheses in macro
bridge: only provide proxy ARP when CONFIG_INET is enabled
neighbour: fix base_reachable_time(_ms) not effective immediatly when changed
net: fec: fix MDIO bus assignement for dual fec SoC's
xen-netfront: use different locks for Rx and Tx stats
drivers: net: cpsw: fix multicast flush in dual emac mode
cxgb4vf: Initialize mdio_addr before using it
net: Corrected the comment describing the ndo operations to reflect the actual prototype for couple of operations
usb/kaweth: use GFP_ATOMIC under spin_lock in usb_start_wait_urb()
MAINTAINERS: add me as ibmveth maintainer
tipc: fix bug in broadcast retransmit code
update ip-sysctl.txt documentation (v2)
net/at91_ether: prepare and unprepare clock
...
|
|
Prashant Sreedharan says:
====================
tg3: synchronize_irq() should be called without taking locks
v2: Added Reported-by, Tested-by fields and reference to the thread that
reported the problem
This series addresses the problem reported by Peter Hurley in mail thread
https://lkml.org/lkml/2015/1/12/1082
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
synchronize_irq() can sleep waiting, for pending IRQ handlers so driver
should release the tp->lock spin lock before invoking synchronize_irq()
Reported-by: Peter Hurley <peter@hurleysoftware.com>
Tested-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Prashant Sreedharan <prashant@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Currently tg3_reset_task() uses only tp->lock for synchronizing with code
paths like tg3_open() etc. But since tp->lock is released before doing
synchronize_irq(), rtnl_lock should be taken in tg3_reset_task() to
synchronize it with other code paths.
Reported-by: Peter Hurley <peter@hurleysoftware.com>
Tested-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Prashant Sreedharan <prashant@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This is to avoid the race between tg3_timer() and the execution paths
which does not invoke tg3_timer_stop() and releases tp->lock before
calling synchronize_irq()
Reported-by: Peter Hurley <peter@hurleysoftware.com>
Tested-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Prashant Sreedharan <prashant@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Pull kvm fixes from Paolo Bonzini:
"Two bugfixes for arm64. I will have another pull request next week,
but otherwise things are calm"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
arm64: KVM: Fix HCR setting for 32bit guests
arm64: KVM: Fix TLB invalidation by IPA/VMID
|
|
mcast_rejoin
This patch is fixing a race condition that may cause setting
count_pending to -1, which results in unwanted big bulk of arp messages
(in case of "notify peers").
Consider following scenario:
count_pending == 2
CPU0 CPU1
team_notify_peers_work
atomic_dec_and_test (dec count_pending to 1)
schedule_delayed_work
team_notify_peers
atomic_add (adding 1 to count_pending)
team_notify_peers_work
atomic_dec_and_test (dec count_pending to 1)
schedule_delayed_work
team_notify_peers_work
atomic_dec_and_test (dec count_pending to 0)
schedule_delayed_work
team_notify_peers_work
atomic_dec_and_test (dec count_pending to -1)
Fix this race by using atomic_dec_if_positive - that will prevent
count_pending running under 0.
Fixes: fc423ff00df3a1955441 ("team: add peer notification")
Fixes: 492b200efdd20b8fcfd ("team: add support for sending multicast rejoins")
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: Jiri Benc <jbenc@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux
Pull s390 fixes from Martin Schwidefsky:
"Two small performance tweaks, the plumbing for the execveat system
call and a couple of bug fixes"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux:
s390/uprobes: fix user space PER events
s390/bpf: Fix JMP_JGE_X (A > X) and JMP_JGT_X (A >= X)
s390/bpf: Fix ALU_NEG (A = -A)
s390/mm: avoid using pmd_to_page for !USE_SPLIT_PMD_PTLOCKS
s390/timex: fix get_tod_clock_ext() inline assembly
s390: wire up execveat syscall
s390/kernel: use stnsm 255 instead of stosm 0
s390/vtime: Get rid of redundant WARN_ON
s390/zcrypt: kernel oops at insmod of the z90crypt device driver
|
|
User space is currently sending a OVS_FLOW_ATTR_PROBE for both flow
and packet messages. This leads to an out-of-bounds access in
ovs_packet_cmd_execute() because OVS_FLOW_ATTR_PROBE >
OVS_PACKET_ATTR_MAX.
Introduce a new OVS_PACKET_ATTR_PROBE with the same numeric value
as OVS_FLOW_ATTR_PROBE to grow the range of accepted packet attributes
while maintaining to be binary compatible with existing OVS binaries.
Fixes: 05da589 ("openvswitch: Add support for OVS_FLOW_ATTR_PROBE.")
Reported-by: Sander Eikelenboom <linux@eikelenboom.it>
Tracked-down-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Thomas Graf <tgraf@suug.ch>
Reviewed-by: Jesse Gross <jesse@nicira.com>
Acked-by: Pravin B Shelar <pshelar@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Adds FCoE config option I40E_FCOE, so that FCoE can be enabled
as needed but otherwise have it disabled by default.
This also eliminate multiple FCoE config checks, instead now just
one config check for CONFIG_I40E_FCOE.
The I40E FCoE was added with 3.17 kernel and therefore this patch
shall be applied to stable 3.17 kernel also.
CC: <stable@vger.kernel.org>
Signed-off-by: Vasu Dev <vasu.dev@intel.com>
Tested-by: Jim Young <jamesx.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Pull file locking fix from Jeff Layton:
"Just a simple bugfix for a regression that I introduced into v3.18
with the internal lease API overhaul -- mea culpa. Kudos to Linda and
Neil for tracking this down and fixing it"
* tag 'locks-v3.19-1' of git://git.samba.org/jlayton/linux:
locks: fix NULL-deref in generic_delete_lease
|
|
For example, one could conceivably call
for_each_netdev_in_bond_rcu(condition ? bond1 : bond2, slave)
and get an unexpected result.
Signed-off-by: Benjamin Poirier <bpoirier@suse.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Pull block layer fixes from Jens Axboe:
"The major part is an update to the NVMe driver, fixing various issues
around surprise removal and hung controllers. Most of that is from
Keith, and parts are simple blk-mq fixes or exports/additions of minor
functions to aid this effort, and parts are changes directly to the
NVMe driver.
Apart from the above, this contains:
- Small blk-mq change from me, killing an unused member of the
hardware queue structure.
- Small fix from Ming Lei, fixing up a few drivers that didn't
properly check for ERR_PTR() returns from blk_mq_init_queue()"
* 'for-linus' of git://git.kernel.dk/linux-block:
NVMe: Fix locking on abort handling
NVMe: Start and stop h/w queues on reset
NVMe: Command abort handling fixes
NVMe: Admin queue removal handling
NVMe: Reference count admin queue usage
NVMe: Start all requests
blk-mq: End unstarted requests on a dying queue
blk-mq: Allow requests to never expire
blk-mq: Add helper to abort requeued requests
blk-mq: Let drivers cancel requeue_work
blk-mq: Export if requests were started
blk-mq: Wake tasks entering queue on dying
blk-mq: get rid of ->cmd_size in the hardware queue
block: fix checking return value of blk_mq_init_queue
block: wake up waiters when a queue is marked dying
NVMe: Fix double free irq
blk-mq: Export freeze/unfreeze functions
blk-mq: Exit queue on alloc failure
|
|
When IPV4 support is disabled, we cannot call arp_send from
the bridge code, which would result in a kernel link error:
net/built-in.o: In function `br_handle_frame_finish':
:(.text+0x59914): undefined reference to `arp_send'
:(.text+0x59a50): undefined reference to `arp_tbl'
This makes the newly added proxy ARP support in the bridge
code depend on the CONFIG_INET symbol and lets the compiler
optimize the code out to avoid the link error.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: 958501163ddd ("bridge: Add support for IEEE 802.11 Proxy ARP")
Cc: Kyeyoon Park <kyeyoonp@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/evalenti/linux-soc-thermal into thermal-soc
|
|
When setting base_reachable_time or base_reachable_time_ms on a
specific interface through sysctl or netlink, the reachable_time
value is not updated.
This means that neighbour entries will continue to be updated using the
old value until it is recomputed in neigh_period_work (which
recomputes the value every 300*HZ).
On systems with HZ equal to 1000 for instance, it means 5mins before
the change is effective.
This patch changes this behavior by recomputing reachable_time after
each set on base_reachable_time or base_reachable_time_ms.
The new value will become effective the next time the neighbour's timer
is triggered.
Changes are made in two places: the netlink code for set and the sysctl
handling code. For sysctl, I use a proc_handler. The ipv6 network
code does provide its own handler but it already refreshes
reachable_time correctly so it's not an issue.
Any other user of neighbour which provide its own handlers must
refresh reachable_time.
Signed-off-by: Jean-Francois Remy <jeff@melix.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
On i.MX28, the MDIO bus is shared between the two FEC instances.
The driver makes sure that the second FEC uses the MDIO bus of the
first FEC. This is done conditionally if FEC_QUIRK_ENET_MAC is set.
However, in newer designs, such as Vybrid or i.MX6SX, each FEC MAC
has its own MDIO bus. Simply removing the quirk FEC_QUIRK_ENET_MAC
is not an option since other logic, triggered by this quirk, is
still needed.
Furthermore, there are board designs which use the same MDIO bus
for both PHY's even though the second bus would be available on the
SoC side. Such layout are popular since it saves pins on SoC side.
Due to the above quirk, those boards currently do work fine. The
boards in the mainline tree with such a layout are:
- Freescale Vybrid Tower with TWR-SER2 (vf610-twr.dts)
- Freescale i.MX6 SoloX SDB Board (imx6sx-sdb.dts)
This patch adds a new quirk FEC_QUIRK_SINGLE_MDIO for i.MX28, which
makes sure that the MDIO bus of the first FEC is used in any case.
However, the boards above do have a SoC with a MDIO bus for each FEC
instance. But the PHY's are not connected in a 1:1 configuration. A
proper device tree description is needed to allow the driver to
figure out where to find its PHY. This patch fixes that shortcoming
by adding a MDIO bus child node to the first FEC instance, along
with the two PHY's on that bus, and making use of the phy-handle
property to add a reference to the PHY's.
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/cooloney/linux-leds
Pull LED fix from Bryan Wu.
* 'leds-fixes-for-3.19' of git://git.kernel.org/pub/scm/linux/kernel/git/cooloney/linux-leds:
leds: netxbig: fix oops at probe time
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/borntraeger/linux
Pull WRITE_ONCE argument order change from Christian Borntraeger:
"As discussed on LKML[1] it was agreed that WRITE_ONCE(x, val) is
better than ASSIGN_ONCE(val, x)
Lets change that for 3.19 as 3.19 has no user yet, but the first users
will hit linux-next soon"
[1] http://marc.info/?l=linux-kernel&m=142081181707596
* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/borntraeger/linux:
kernel: Change ASSIGN_ONCE(val, x) to WRITE_ONCE(x, val)
|
|
In netfront the Rx and Tx path are independent and use different
locks. The Tx lock is held with hard irqs disabled, but Rx lock is
held with only BH disabled. Since both sides use the same stats lock,
a deadlock may occur.
[ INFO: possible irq lock inversion dependency detected ]
3.16.2 #16 Not tainted
---------------------------------------------------------
swapper/0/0 just changed the state of lock:
(&(&queue->tx_lock)->rlock){-.....}, at: [<c03adec8>]
xennet_tx_interrupt+0x14/0x34
but this lock took another, HARDIRQ-unsafe lock in the past:
(&stat->syncp.seq#2){+.-...}
and interrupts could create inverse lock ordering between them.
other info that might help us debug this:
Possible interrupt unsafe locking scenario:
CPU0 CPU1
---- ----
lock(&stat->syncp.seq#2);
local_irq_disable();
lock(&(&queue->tx_lock)->rlock);
lock(&stat->syncp.seq#2);
<Interrupt>
lock(&(&queue->tx_lock)->rlock);
Using separate locks for the Rx and Tx stats fixes this deadlock.
Reported-by: Dmitry Piotrovsky <piotrovskydmitry@gmail.com>
Signed-off-by: David Vrabel <david.vrabel@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Since ALE table is a common resource for both the interfaces in Dual EMAC
mode and while bringing up the second interface in cpsw_ndo_set_rx_mode()
all the multicast entries added by the first interface is flushed out and
only second interface multicast addresses are added. Fixing this by
flushing multicast addresses based on dual EMAC port vlans which will not
affect the other emac port multicast addresses.
Fixes: d9ba8f9 (driver: net: ethernet: cpsw: dual emac interface implementation)
Cc: <stable@vger.kernel.org> # v3.9+
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch fixes a NULL pointer dereference on led_dat->mode_val. Due to
this bug, a kernel oops can be observed at probe time on the LaCie 2Big
and 5Big v2 boards:
Unable to handle kernel NULL pointer dereference at virtual address 00000008
[...]
[<c03f244c>] (netxbig_led_probe) from [<c02c8c6c>] (platform_drv_probe+0x4c/0x9c)
[<c02c8c6c>] (platform_drv_probe) from [<c02c72d0>] (driver_probe_device+0x98/0x25c)
[<c02c72d0>] (driver_probe_device) from [<c02c7520>] (__driver_attach+0x8c/0x90)
[<c02c7520>] (__driver_attach) from [<c02c5c24>] (bus_for_each_dev+0x68/0x94)
[<c02c5c24>] (bus_for_each_dev) from [<c02c6408>] (bus_add_driver+0x124/0x1dc)
[<c02c6408>] (bus_add_driver) from [<c02c7ac0>] (driver_register+0x78/0xf8)
[<c02c7ac0>] (driver_register) from [<c000888c>] (do_one_initcall+0x80/0x1cc)
[<c000888c>] (do_one_initcall) from [<c0733618>] (kernel_init_freeable+0xe4/0x1b4)
[<c0733618>] (kernel_init_freeable) from [<c058db9c>] (kernel_init+0xc/0xec)
[<c058db9c>] (kernel_init) from [<c0009850>] (ret_from_fork+0x14/0x24)
[...]
This bug was introduced by commit 588a6a99286ae30afb1339d8bc2163517b1b7dd1
("leds: netxbig: fix attribute-creation race").
Signed-off-by: Simon Guinot <simon.guinot@sequanux.org>
Cc: <stable@vger.kernel.org> # 3.17+
Acked-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
|
|
In commit 5ad24def21b205a8 ("cxgb4vf: Fix ethtool get_settings for VF driver")
mdio_addr of port_info structure was used unininitialzed. Fixing it.
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Feedback has shown that WRITE_ONCE(x, val) is easier to use than
ASSIGN_ONCE(val,x).
There are no in-tree users yet, so lets change it for 3.19.
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Acked-by: Peter Zijlstra <peterz@infradead.org>
Acked-by: Davidlohr Bueso <dave@stgolabs.net>
Acked-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/shuah/linux-kselftest
Pull kselftest fixes from Shuah Khan:
"This update contains three patches to fix one compile error, and two
run-time bugs. One of them fixes infinite loop on ARM"
* tag 'linux-kselftest-3.19-rc-5' of git://git.kernel.org/pub/scm/linux/kernel/git/shuah/linux-kselftest:
selftests/vm: fix link error for transhuge-stress test
tools: testing: selftests: mq_perf_tests: Fix infinite loop on ARM
selftests/exec: allow shell return code of 126
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip
Pull xen bug fixes from David Vrabel:
"Several critical linear p2m fixes that prevented some hosts from
booting"
* tag 'stable/for-linus-3.19-rc4-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip:
x86/xen: properly retrieve NMI reason
xen: check for zero sized area when invalidating memory
xen: use correct type for physical addresses
xen: correct race in alloc_p2m_pmd()
xen: correct error for building p2m list on 32 bits
x86/xen: avoid freeing static 'name' when kasprintf() fails
x86/xen: add extra memory for remapped frames during setup
x86/xen: don't count how many PFNs are identity mapped
x86/xen: Free bootmem in free_p2m_page() during early boot
x86/xen: Remove unnecessary BUG_ON(preemptible()) in xen_setup_timer()
|
|
actual prototype for couple of operations
Corrected the comment describing the ndo operations to
reflect the actual prototype for couple of operations
Signed-off-by: B Viswanath <marichika4@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rzhang/linux
Pull thermal management fixes from Zhang Rui:
"Specifics:
- Fix a problem that Intel SoC DTS thermal driver does not work when
CONFIG_THERMAL_INT340X is not set.
- Fix a NULL pointer dereference when processor_thermal_device driver
is loaded on a platform without ACPI support"
* 'for-rc' of git://git.kernel.org/pub/scm/linux/kernel/git/rzhang/linux:
int340x_thermal/processor_thermal_device: return failure when
ACPI/int340x_thermal: enumerate INT3401 for Intel SoC DTS thermal driver
ACPI/int340x_thermal: enumerate INT340X devices even if they're not in _ART/_TRT
|
|
commit 0efaa7e82f02fe69c05ad28e905f31fc86e6f08e
locks: generic_delete_lease doesn't need a file_lock at all
moves the call to fl->fl_lmops->lm_change() to a place in the
code where fl might be a non-lease lock.
When that happens, fl_lmops is NULL and an Oops ensures.
So add an extra test to restore correct functioning.
Reported-by: Linda Walsh <suse@tlinx.org>
Link: https://bugzilla.suse.com/show_bug.cgi?id=912569
Cc: stable@vger.kernel.org (v3.18)
Fixes: 0efaa7e82f02fe69c05ad28e905f31fc86e6f08e
Signed-off-by: NeilBrown <neilb@suse.de>
Signed-off-by: Jeff Layton <jlayton@primarydata.com>
|
|
Using the native code here can't work properly, as the hypervisor would
normally have cleared the two reason bits by the time Dom0 gets to see
the NMI (if passed to it at all). There's a shared info field for this,
and there's an existing hook to use - just fit the two together. This
is particularly relevant so that NMIs intended to be handled by APEI /
GHES actually make it to the respective handler.
Note that the hook can (and should) be used irrespective of whether
being in Dom0, as accessing port 0x61 in a DomU would be even worse,
while the shared info field would just hold zero all the time. Note
further that hardware NMI handling for PVH doesn't currently work
anyway due to missing code in the hypervisor (but it is expected to
work the native rather than the PV way).
Signed-off-by: Jan Beulich <jbeulich@suse.com>
Reviewed-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Signed-off-by: David Vrabel <david.vrabel@citrix.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull gpio fixes from Linus Walleij:
"Here are some GPIO fixes, mainly affecting the DLN2 IRQ handling.
Nothing special about them, just fixes:
- Three patches fixing IRQ handling for the DLN2
- Null pointer handling for grgpio"
* tag 'gpio-v3.19-3' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio:
gpio: dln2: use bus_sync_unlock instead of scheduling work
gpio: grgpio: Avoid potential NULL pointer dereference
gpio: dln2: Fix gpio output value in dln2_gpio_direction_output()
gpio: dln2: fix issue when an IRQ is unmasked then enabled
|
|
Pull MMC fixes from Ulf Hansson:
"MMC host:
- sdhci-pci|acpi: Support some new IDs
- sdhci: Fix sleep from atomic context
- sdhci-pxav3: Prevent hang during ->probe()
- sdhci: Disable re-tuning for HS400"
* tag 'mmc-v3.19-3' of git://git.linaro.org/people/ulf.hansson/mmc:
mmc: sdhci-pci: Add support for Intel SPT
mmc: sdhci-acpi: Add ACPI HID INT344D
mmc: sdhci: Fix sleep in atomic after inserting SD card
mmc: sdhci-pxav3: do the mbus window configuration after enabling clocks
mmc: sdhci: Disable re-tuning for HS400
mmc: sdhci: Simplify use of tuning timer
mmc: sdhci: Add out_unlock to sdhci_execute_tuning
mmc: sdhci: Tuning should not change max_blk_count
|
|
Pull scsi target fixes from Nicholas Bellinger:
"Mostly minor fixes this time, including:
- Add missing virtio-scsi -> TCM attribute conversion in vhost-scsi.
- Fix persistent reservations write exclusive handling to allow
readers for all registered I_T nexuses.
- Drop arbitrary maximum I/O size limit in order to process I/Os
larger than 4 MB, required for initiators that don't honor block
limits EVPD.
- Drop the now left-over fabric_max_sectors attribute"
* git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending:
iscsi-target: Fix typos in enum cmd_flags_table
MAINTAINERS: Add entry for iSER target driver
target: Allow Write Exclusive non-reservation holders to READ
target: Drop left-over fabric_max_sectors attribute
target: Drop arbitrary maximum I/O size limit
Documentation/target: Update fabric_ops to latest code
vhost-scsi: Add missing virtio-scsi -> TCM attribute conversion
|
|
When batching up address ranges for TLB invalidation, we check tlb->end
!= 0 to indicate that some pages have actually been unmapped.
As of commit f045bbb9fa1b ("mmu_gather: fix over-eager
tlb_flush_mmu_free() calling"), we use the same check for freeing these
pages in order to avoid a performance regression where we call
free_pages_and_swap_cache even when no pages are actually queued up.
Unfortunately, the range could have been reset (tlb->end = 0) by
tlb_end_vma, which has been shown to cause memory leaks on arm64.
Furthermore, investigation into these leaks revealed that the fullmm
case on task exit no longer invalidates the TLB, by virtue of tlb->end
== 0 (in 3.18, need_flush would have been set).
This patch resolves the problem by reverting commit f045bbb9fa1b, using
instead tlb->local.nr as the predicate for page freeing in
tlb_flush_mmu_free and ensuring that tlb->end is initialised to a
non-zero value in the fullmm case.
Tested-by: Mark Langsdorf <mlangsdo@redhat.com>
Tested-by: Dave Hansen <dave@sr71.net>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Commit e4c7f259c5be ("USB: kaweth.c: use GFP_ATOMIC under spin_lock")
makes sure that kaweth_internal_control_msg() allocates memory with GFP_ATOMIC,
but kaweth_internal_control_msg() also calls usb_start_wait_urb()
that still allocates memory with GFP_NOIO.
The patch fixes usb_start_wait_urb() as well.
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Acked-by: Oliver Neukum <oliver@neukum.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Adding myself as the ibmveth maintainer and replacing
Santiago Leon.
Signed-off-by: Thomas Falcon <tlfalcon@linux.vnet.ibm.com>
Cc: Santiago Leon <santi_leon@yahoo.com>
Cc: Brian King <brking@linux.vnet.ibm.com>
Cc: Nathan Fontenot <nfont@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In commit 58dc55f25631178ee74cd27185956a8f7dcb3e32 ("tipc: use generic
SKB list APIs to manage link transmission queue") we replace all list
traversal loops with the macros skb_queue_walk() or
skb_queue_walk_safe(). While the previous loops were based on the
assumption that the list was NULL-terminated, the standard macros
stop when the iterator reaches the list head, which is non-NULL.
In the function bclink_retransmit_pkt() this macro replacement has
lead to a bug. When we receive a BCAST STATE_MSG we unconditionally
call the function bclink_retransmit_pkt(), whether there really is
anything to retransmit or not, assuming that the sequence number
comparisons will lead to the correct behavior. However, if the
transmission queue is empty, or if there are no eligible buffers in
the transmission queue, we will by mistake pass the list head pointer
to the function tipc_link_retransmit(). Since the list head is not a
valid sk_buff, this leads to a crash.
In this commit we fix this by only calling tipc_link_retransmit()
if we actually found eligible buffers in the transmission queue.
Reviewed-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
|
|
Update documentation to reflect the fact that
/proc/sys/net/ipv4/route/max_size is no longer used for ipv4.
Signed-off-by: Ani Sinha <ani@arista.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The clock is enabled without being prepared, this leads to:
WARNING: CPU: 0 PID: 1 at drivers/clk/clk.c:889 __clk_enable+0x24/0xa8()
and a non working ethernet interface.
Use clk_prepare_enable() and clk_disable_unprepare() to handle the clock.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In C one can either use '\0' or '\x00' (or '\000') to add a NUL byte to
a string. '\0x00' isn't part of these and will in fact result in a
single NUL followed by "x00". This fixes that.
Signed-off-by: Giel van Schijndel <me@mortis.eu>
Reported-at: http://www.viva64.com/en/b/0299/
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Commit b856a59141b1 (arm/arm64: KVM: Reset the HCR on each vcpu
when resetting the vcpu) moved the init of the HCR register to
happen later in the init of a vcpu, but left out the fixup
done in kvm_reset_vcpu when preparing for a 32bit guest.
As a result, the 32bit guest is run as a 64bit guest, but the
rest of the kernel still manages it as a 32bit. Fun follows.
Moving the fixup to vcpu_reset_hcr solves the problem for good.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
It took about two years for someone to notice that the IPA passed
to TLBI IPAS2E1IS must be shifted by 12 bits. Clearly our reviewing
is not as good as it should be...
Paper bag time for me.
Reported-by: Mario Smarduch <m.smarduch@samsung.com>
Tested-by: Mario Smarduch <m.smarduch@samsung.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
With the introduction of the linear mapped p2m list setting memory
areas to "invalid" had to be delayed. When doing the invalidation
make sure no zero sized areas are processed.
Signed-off-by: Juegren Gross <jgross@suse.com>
Signed-off-by: David Vrabel <david.vrabel@citrix.com>
|
|
When converting a pfn to a physical address be sure to use 64 bit
wide types or convert the physical address to a pfn if possible.
Signed-off-by: Juergen Gross <jgross@suse.com>
Tested-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Signed-off-by: David Vrabel <david.vrabel@citrix.com>
|
