Age | Commit message (Collapse) | Author |
|
- instead of a mute module option, use audmode as per the spec.
- clamp the frequency before setting it.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
Such ioctls are not valid for radio devices.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
Don't set version (done by the v4l2 core), fill in bus_info, set correct
driver name and add device_caps support.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
The inputmask for the tea6420 wasn't set and the wrong mute register value
was used.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
The balance control did not do what it is supposed to do due to wrong
calculations.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Tested-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
When the control IDs were split off from videodev2.h to v4l2-controls.h
these new Digital Video controls were forgotten (the two patches may
have crossed one another).
Move these controls to their proper place in v4l2-controls.h.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
Newer Exynos4 SoC are equipped with a local camera ISP that
controls external raw image sensor directly. Such sensors
can be connected through FIMC-LITEn (and MIPI-CSISn) IPs to
the ISP, which then feeds image data to the FIMCn IP. Thus
there can be two busses associated with an image source
(sensor). Rename struct s5p_fimc_isp_info describing external
image sensor (video decoder) to struct fimc_source_info to
avoid confusion. bus_type is split into fimc_bus_type and
sensor_bus_type. The bus type enumeration is extended to
include both FIMC Writeback input types.
The bus_type enumeration and the data structure name in the
board files are modified according to the above changes.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
devm_regulator_bulk_get saves some cleanup and exit code.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
Add clk_prepare(), clk_unprepare() calls for the sclk_cam clocks
to ensure the driver works on platforms with the common clocks
API enabled.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
The V4L2_SEL_TGT_CROP_BOUNDS, V4L2_SEL_TGT_COMPOSE_BOUNDS selection
targets are not supposed to be handled in the set_selection ioctl.
Remove the code that doesn't do anything sensible now and make sure
ctx->state is modified with the spinlock held.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
Make sure a valid image format is initially set on both the CAPTURE
and the OUTPUT buffer queue.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
With presence of some faults, e.g. caused by wrong platform data or
the device tree structure the IDX_SENSOR entry in the array may be NULL,
so make sure it is not dereferenced then.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
Fixes the following sparse warnings:
drivers/media/i2c/s5c73m3/s5c73m3-core.c:42:5: warning:
symbol 'boot_from_rom' was not declared. Should it be static?
drivers/media/i2c/s5c73m3/s5c73m3-core.c:45:5: warning:
symbol 'update_fw' was not declared. Should it be static?
drivers/media/i2c/s5c73m3/s5c73m3-core.c:298:5: warning:
symbol 's5c73m3_isp_comm_result' was not declared. Should it be static?
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
clk_set_rate(), clk_enable() functions can fail, so check the return
values to avoid surprises. While at it use ERR_PTR() value to indicate
an invalid clock.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
clk_set_rate(), clk_enable() functions can fail, so check the return
values to avoid surprises. While at it use ERR_PTR() value to indicate
an invalid clock.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
The previous method of registering platform entities into the main
driver using driver_find() and then iterating over devices bound to
a driver was racy and is being removed here. Nothing was preventing
module from unloading during a call to try_module_get(driver->owner).
Instead, we look up a device first and then check for its driver while
holding device lock.
The platform sub-devices are looked up and registered to the top
level driver. When any sub-device is not yet initialized and ready
the main driver's probe() will be deferred.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
Add missing line breaks in the debug traces.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
devm_regulator_bulk_get is device managed and saves some cleanup
and exit code.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
This patch fixes regression introduced in commit 6319d6a002beb26631
'[media] fimc-lite: Add ISP FIFO output support'.
In case of a configuration where video is captured at the video node
exposed by the FIMC-LITE driver there is a following video pipeline:
sensor -> MIPI-CSIS.n -> FIMC-LITE.n subdev -> FIMC-LITE.n video node
In this situation s_stream() handler of the FIMC-LITE.n is called
back from within VIDIOC_STREAMON/OFF ioctl of the FIMC-LITE.n video
node, through vb2_stream_on/off(), start/stop_streaming and
fimc_pipeline_call(set_stream). The fimc->lock mutex is already held
then, before invoking vidioc_streamon/off. So it must not be taken
again in the s_stream() callback in this case, to avoid a deadlock.
This patch makes fimc->out_path atomic_t so the mutex don't need
to be taken in the FIMC-LITE subdev s_stream() callback in the DMA
output case.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyugmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
The .s_power FIMC-LITE subdev callback is now empty and
unneeded. The FIMC-LITE IP power handling will be done
by the FIMC-IS driver, so just remove the callback.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
Add driver for S5C73M3 image sensor. The driver exposes the sensor as
two subdevs: pure sensor and output interface. Two subdev architecture
supports interleaved UYVY/JPEG image format with separate frame size
for both sub-formats, there is a spearate pad for each sub-format.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
Cleaned up the memory devices allocation code and added
missing device_initialize() call to remove the kernel warning
during memory allocations.
Signed-off-by: Arun Kumar K <arun.kk@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
Use WARN_ON(condition) directly instead of wrapping around an if
condition.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
devm_regulator_bulk_get is device managed and saves some cleanup
and exit code.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
All host drivers using this subdev driver are already converted
to use the control framework so the compatibility ops can be dropped.
Signed-off-by: Sylwester Nawrocki <sylvester.nawrocki@gmail.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
Modified the G2D driver (which initially supported only H/W Rev.3)
to support H/W Rev.4.1 present on Exynos4x12 and Exynos52x0 SOCs.
- Set the SRC and DST type to 'memory' instead of using reset values.
- FIMG2D v4.1 H/W uses different logic for stretching(scaling).
- Use CACHECTL_REG only with FIMG2D v3.
[s.nawrocki: removed empty line at end of file]]
Signed-off-by: Ajay Kumar <ajaykumar.rs@samsung.com>
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Acked-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
Fixes the following warning:
drivers/media/platform/s5p-mfc/s5p_mfc_opr.c:56:27: warning:
Using plain integer as NULL pointer
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
Make sure bytesperline for Cb, Cr planes for V4L2_PIX_FMT_YUV420M
format is half of the Y plane value, rather than having same
bytesperline for all planes.
While at it, simplify the bytesperline parameter handling by
storing it when image format is set and returning those values
when getting the format, instead of recalculating bytesperline
from intermediate parameters.
Reported-by: Sebastian Dröge <sebastian.droege@collabora.co.uk>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
Fixed wrong condition in firmware reload function used by the watchdog.
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
Fixes a v4l2-compliance error: setting audmode to a value other than mono
or stereo for a radio device should map to MODE_STEREO.
The spec specifies that for radio devices only mono and stereo audmodes are
valid. If the user specifies another audmode in v4l2_tuner, then that should
be mapped to valid audmode. That didn't happen here.
Note that tuner drivers might decide to limit the possible audmode even
further if it only supports mono. In that case the tuner driver can set
audmode to mono. However, that new value wasn't copied back to t->audmode,
and that has been fixed as well in this patch.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
This patch adds V4L2 sub-device driver for OV9650/OV9652 image sensors.
The driver exposes following V4L2 controls:
- auto/manual exposure,
- auto/manual white balance,
- auto/manual gain,
- brightness, saturation, sharpness,
- horizontal/vertical flip,
- color bar test pattern,
- banding filter (power line frequency).
Frame rate can be configured with g/s_frame_interval pad level ops.
Supported resolution are only: SXGA, VGA, QVGA.
Signed-off-by: Sylwester Nawrocki <sylvester.nawrocki@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
This patch adds a v4l2 core helper function that can be used as
the log_status handler for subdevs that only need to log state
of the v4l2 controls owned by the subdev's control handler.
Signed-off-by: Sylwester Nawrocki <sylvester.nawrocki@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
Add a v4l2 core helper function that can be used as the subdev
.subscribe_event handler. This allows to eliminate some boilerplate
from drivers that are only handling the control events.
Signed-off-by: Sylwester Nawrocki <sylvester.nawrocki@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
Add a v4l2 core helper function that can be used as the subdev
.unsubscribe_event handler. This allows to eliminate some
boilerplate from drivers that are only handling the control events.
Signed-off-by: Sylwester Nawrocki <sylvester.nawrocki@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
This patch adds a helper function that allows to modify range,
i.e. minimum, maximum, step and default value of a v4l2 control,
after the control has been created and initialized. This is helpful
in situations when range of a control depends on user configurable
parameters, e.g. camera sensor absolute exposure time depending on
an output image resolution and frame rate.
v4l2_ctrl_modify_range() function allows to modify range of an
INTEGER, BOOL, MENU, INTEGER_MENU and BITMASK type controls.
Based on a patch from Hans Verkuil http://patchwork.linuxtv.org/patch/8654.
Signed-off-by: Sylwester Nawrocki <sylvester.nawrocki@gmail.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
Add common header file defining standard image sizes, so we can
avoid redefining those in each driver.
Signed-off-by: Sylwester Nawrocki <sylvester.nawrocki@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
Instead chaneg the passed in format to the pwc default pixelformat.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
replace:
#if defined(CONFIG_INPUT) || \
defined(CONFIG_INPUT_MODULE)
with:
#if IS_ENABLED(CONFIG_INPUT)
This change was made for: CONFIG_INPUT
Reported-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Peter Senna Tschudin <peter.senna@gmail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
replace:
#if defined(CONFIG_INPUT) || \
defined(CONFIG_INPUT_MODULE)
with:
#if IS_ENABLED(CONFIG_INPUT)
This change was made for: CONFIG_INPUT
Reported-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Peter Senna Tschudin <peter.senna@gmail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
replace:
#if defined(CONFIG_INPUT) || \
defined(CONFIG_INPUT_MODULE)
with:
#if IS_ENABLED(CONFIG_INPUT)
This change was made for: CONFIG_INPUT
Reported-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Peter Senna Tschudin <peter.senna@gmail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
replace:
#if defined(CONFIG_INPUT) || \
defined(CONFIG_INPUT_MODULE)
with:
#if IS_ENABLED(CONFIG_INPUT)
This change was made for: CONFIG_INPUT
Reported-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Peter Senna Tschudin <peter.senna@gmail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
replace:
#if defined(CONFIG_INPUT) || \
defined(CONFIG_INPUT_MODULE)
with:
#if IS_ENABLED(CONFIG_INPUT)
This change was made for: CONFIG_INPUT
Reported-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Peter Senna Tschudin <peter.senna@gmail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
replace:
#if defined(CONFIG_INPUT) || \
defined(CONFIG_INPUT_MODULE)
with:
#if IS_ENABLED(CONFIG_INPUT)
This change was made for: CONFIG_INPUT
Reported-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Peter Senna Tschudin <peter.senna@gmail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
replace:
#if defined(CONFIG_INPUT) || \
defined(CONFIG_INPUT_MODULE)
with:
#if IS_ENABLED(CONFIG_INPUT)
This change was made for: CONFIG_INPUT
Also replaced:
#if !defined CONFIG_USB_SN9C102 && !defined CONFIG_USB_SN9C102_MODULE
with:
#if !IS_ENABLED(CONFIG_USB_SN9C102)
Reported-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Peter Senna Tschudin <peter.senna@gmail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
replace:
#if defined(CONFIG_INPUT) || \
defined(CONFIG_INPUT_MODULE)
with:
#if IS_ENABLED(CONFIG_INPUT)
This change was made for: CONFIG_INPUT
Reported-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Peter Senna Tschudin <peter.senna@gmail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|