| Age | Commit message (Collapse) | Author |
|---|
|
If IRQ triggering is enabled, it can trigger a pending interrupt
even for masked interrupts. Any pending GPIO interrupts can
prevent the powerdomain from hitting retention.
Problem found, reported and additional review and testing by Chunquiu
Wang.
Tested-by: Chunquiu Wang <cqwang@motorola.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
|
|
Powerdomain previous state is checked after restoring new states in
suspend. This patch fixes this problem.
Signed-off-by: Jouni Hogander <jouni.hogander@nokia.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
|
|
Use the min/max settings from CPUfreq policy rather than
processor defined min/max settings.
Without this patch, it's possible to scale frequency outside
the current policy range.
Signed-off-by: Eero Nurkkala <ext-eero.nurkkala@nokia.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
|
|
Use list_add_tail() when adding discovered UART ports. This is so
traversal using list_for_each_entry() will traverse the list in the
order they were found.
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
|
|
This patch causes the OMAP uarts to honor the sysfs power/wakeup file
for IOPAD wakeups. Before the OMAP was always woken up from off mode
on a rs232 signal change. This patch also creates a different
platform device for each serial port so that the wakeup properties can
be control per port.
By default, IOPAD wakeups are enabled for each UART. To disable,
# echo disabled > /sys/devices/platform/serial8250.0/power/wakeup
Where serial8250.0 can be replaced by .1, or .2 to control the other
ports.
Original idea and original patch from Russ Dill <russ.dill@gmail.com>
Cc: Russ Dill <russ.dill@gmail.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
|
|
It was possible for an unhandled interrupt to occur if there was incoming
serial traffic during wakeup from suspend. This was caused by the code
in arch-arm/mach-omap2/serial.c keeping interrupt enabled all the time,
but not acking its interrupts. Applies on top of PM branch.
Use the PM begin/end hooks to ensure that the "serial idle" interrupts
are disabled during the suspend path. Also, since begin/end hooks are
now used, use the suspend_state that is passed in the begin hook instead
of the enter hook as per the platform_suspend_ops docs.
Signed-off-by: Tero Kristo <tero.kristo@nokia.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
|
|
Streamline the OMAP4 special IRQ assignments by putting inside
normal init loop instead of having a separate loop.
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
|
|
Signed-off-by: Jouni Hogander <jouni.hogander@nokia.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
|
|
By default, prevent functional wakeups from inside a module from
waking up the IVA2. Let DSP Bridge code handle this when loaded.
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
|
|
Any pending reset flags can prevent retention. Ensure they are all
cleared during boot.
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
|
|
Any pending PRCM interrupts can prevent retention. Ensure
they are cleared during boot.
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
|
|
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
|
|
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
|
|
|
|
* 'for-linus' of git://oss.sgi.com/xfs/xfs:
xfs: bump up nr_to_write in xfs_vm_writepage
xfs: reduce bmv_count in xfs_vn_fiemap
|
|
* 'for-linus' of git://git.kernel.dk/linux-2.6-block:
io context: fix ref counting
block: make the end_io functions be non-GPL exports
block: fix improper kobject release in blk_integrity_unregister
block: always assign default lock to queues
mg_disk: Add missing ready status check on mg_write()
mg_disk: fix issue with data integrity on error in mg_write()
mg_disk: fix reading invalid status when use polling driver
mg_disk: remove prohibited sleep operation
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip
* 'timers-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
clocksource: Save mult_orig in clocksource_disable()
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/drzeus/mmc
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/drzeus/mmc:
mmc: orphan subsystem
imxmmc: Remove unnecessary semicolons
cb710: use SG_MITER_TO_SG/SG_MITER_FROM_SG
sdhci: use SG_MITER_TO_SG/SG_MITER_FROM_SG
lib/scatterlist: add a flags to signalize mapping direction
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6:
ALSA: sound/aoa: Add kmalloc NULL tests
ALSA: hda - Increase PCM stream name buf in patch_realtek.c
sound: mpu401.c: Buffer overflow
sound: aedsp16: Buffer overflow
ALSA: hda: fix out-of-bound hdmi_eld.sad[] write
ALSA: hda - Add quirk for Dell Studio 1555
|
|
To fix the common case where ->enable() does not set up
mult, make sure mult_orig is saved in mult on disable.
Also add comments to explain why we do this.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Cc: johnstul@us.ibm.com
Cc: lethal@linux-sh.org
Cc: akpm@linux-foundation.org
LKML-Reference: <20090618152432.10136.9932.sendpatchset@rx1.opensource.se>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
I do not have the time to take care of this, so remove myself as
maintainer.
Signed-off-by: Pierre Ossman <pierre@ossman.eu>
|
|
Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: Pavel Pisa <pisa@cmp.felk.cvut.cz>
Signed-off-by: Pierre Ossman <pierre@ossman.eu>
|
|
the code allready uses flush_kernel_dcache_page(). This patch updates the
driver to the recent sg API changes which require that either SG_MITER_TO_SG
or SG_MITER_FROM_SG is set. SG_MITER_TO_SG calls flush_kernel_dcache_page()
in sg_mitter_stop()
Signed-off-by: Sebastian Andrzej Siewior <sebastian@breakpoint.cc>
Acked-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: Pierre Ossman <pierre@ossman.eu>
|
|
so the page will be flushed on unmap on ARCH which need it.
Signed-off-by: Sebastian Andrzej Siewior <sebastian@breakpoint.cc>
Signed-off-by: Pierre Ossman <pierre@ossman.eu>
|
|
sg_miter_start() is currently unaware of the direction of the copy
process (to or from the scatter list). It is important to know the
direction because the page has to be flushed in case the data written
is seen on a different mapping in user land on cache incoherent
architectures.
Signed-off-by: Sebastian Andrzej Siewior <sebastian@breakpoint.cc>
Acked-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Acked-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Pierre Ossman <pierre@ossman.eu>
|
|
* fix/oss:
sound: mpu401.c: Buffer overflow
sound: aedsp16: Buffer overflow
|
|
* fix/misc:
ALSA: sound/aoa: Add kmalloc NULL tests
|
|
* fix/hda:
ALSA: hda - Increase PCM stream name buf in patch_realtek.c
ALSA: hda: fix out-of-bound hdmi_eld.sad[] write
ALSA: hda - Add quirk for Dell Studio 1555
|
|
Check that the result of kzalloc is not NULL before a dereference.
The semantic match that finds this problem is as follows:
(http://www.emn.fr/x-info/coccinelle/)
// <smpl>
@@
expression *x;
identifier f;
constant char *C;
@@
x = \(kmalloc\|kcalloc\|kzalloc\)(...);
... when != x == NULL
when != x != NULL
when != (x || ...)
(
kfree(x)
|
f(...,C,...,x,...)
|
*f(...,x,...)
|
*x->f
)
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
The name buf with size 16 is too short for some codec names, e.g.
truncated like "ALC861-VD Analo". Now the size is doubled.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Commit d9c7d394a8ebacb60097b192939ae9f15235225e
("block: prevent possible io_context->refcount overflow") mistakenly
changed atomic_inc(&ioc->nr_tasks) to atomic_long_inc(&ioc->refcount).
Signed-off-by: Li Zefan <lizf@cn.fujitsu.com>
Acked-by: Nikanth Karthikesan <knikanth@suse.de>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
|
|
VM calculation for nr_to_write seems off. Bump it way
up, this gets simple streaming writes zippy again.
To be reviewed again after Jens' writeback changes.
Signed-off-by: Christoph Hellwig <hch@infradead.org>
Signed-off-by: Eric Sandeen <sandeen@sandeen.net>
Cc: Chris Mason <chris.mason@oracle.com>
Reviewed-by: Felix Blyakher <felixb@sgi.com>
Signed-off-by: Felix Blyakher <felixb@sgi.com>
|
|
commit 6321e3ed2acf3ee9643cdd403e1c88605d7944ba caused
the full bmv_count's worth of getbmapx structures to get
allocated; telling it to do MAXEXTNUM was a bit insane,
resulting in ENOMEM every time.
Chop it down to something reasonable, the number of slots
in the caller's input buffer. If this is too large the
caller may get ENOMEM but the reason should not be a
mystery, and they can try again with something smaller.
We add 1 to the value because in the normal getbmap
world, bmv_count includes the header and xfs_getbmap does:
nex = bmv->bmv_count - 1;
if (nex <= 0)
return XFS_ERROR(EINVAL);
Signed-off-by: Eric Sandeen <sandeen@sandeen.net>
Reviewed-by: Olaf Weber <olaf@sgi.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Felix Blyakher <felixb@sgi.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip
* 'tracing-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
tracing/stat: Fix seqfile memory leak
function-graph: Fix seqfile memory leak
trace_stack: Fix seqfile memory leak
profile: Suppress warning about large allocations when profile=1 is specified
|
|
* git://git.kernel.org/pub/scm/linux/kernel/git/mason/btrfs-unstable:
Btrfs: be more polite in the async caching threads
Btrfs: preserve commit_root for async caching
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/djbw/async_tx
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/djbw/async_tx:
dmaengine: at_hdmac: add DMA slave transfers
dmaengine: at_hdmac: new driver for the Atmel AHB DMA Controller
dmaengine: dmatest: correct thread_count while using multiple thread per channel
dmaengine: dmatest: add a maximum number of test iterations
drivers/dma: Remove unnecessary semicolons
drivers/dma/fsldma.c: Remove unnecessary semicolons
dmaengine: move HIGHMEM64G restriction to ASYNC_TX_DMA
fsldma: do not clear bandwidth control bits on the 83xx controller
fsldma: enable external start for the 83xx controller
fsldma: use PCI Read Multiple command
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jack/linux-udf-2.6
* 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jack/linux-udf-2.6:
udf: Fix loading of VAT inode when drive wrongly reports number of recorded blocks
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jack/linux-quota-2.6
* 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jack/linux-quota-2.6:
quota: Silence lockdep on quota_on
|
|
* git://git.infradead.org/users/cbou/battery-2.6.31:
Add ds2782 battery gas gauge driver
olpc_battery: Ensure that the TRICKLE bit is checked
olpc_battery: Fix up eeprom read function
|
|
* git://git.kernel.org/pub/scm/linux/kernel/git/steve/gfs2-2.6-fixes:
GFS2: remove dcache entries for remote deleted inodes
GFS2: Fix incorrent statfs consistency check
GFS2: Don't put unlikely reclaim candidates on the reclaim list.
GFS2: Don't try and dealloc own inode
GFS2: Fix panic in glock memory shrinker
GFS2: keep statfs info in sync on grows
GFS2: Shrink the shrinker
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc:
powerpc: Update defconfigs for embedded 6xx/7xxx, 8xx, 8{3,5,6}xxx
powerpc/86xx: Update GE Fanuc sbc310 default configuration
powerpc/86xx: Update defconfig for GE Fanuc's PPC9A
cpm_uart: Don't use alloc_bootmem in cpm_uart_cpm2.c
powerpc/83xx: Fix PCI IO base address on MPC837xE-RDB boards
powerpc/85xx: Don't scan for TBI PHY addresses on MPC8569E-MDS boards
powerpc/85xx: Fix ethernet link detection on MPC8569E-MDS boards
powerpc/mm: Fix SMP issue with MMU context handling code
|
|
* git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux-2.6-for-linus:
lguest and virtio: cleanup struct definitions to Linux style.
lguest: update commentry
lguest: fix comment style
virtio: refactor find_vqs
virtio: delete vq from list
virtio: fix memory leak on device removal
lguest: fix descriptor corruption in example launcher
lguest: dereferencing freed mem in add_eventfd()
|
|
Use kernel_text_address() for checking probe address instead of
__kernel_text_address(), because __kernel_text_address() returns true
for init functions even after relaseing those functions.
That will hit a BUG() in text_poke().
Signed-off-by: Masami Hiramatsu <mhiramat@redhat.com>
Cc: Ananth N Mavinakayanahalli <ananth@in.ibm.com>
Cc: Jim Keniston <jkenisto@us.ibm.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Not that anybody can blame him. It's a morass. But hey, it's way
better than it _used_ to be, though, so thanks for all the fish.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Commit d01730d74d2b0155da50d44555001706294014f7 didn't completely fix
the problem since we still take dqio_mutex and i_mutex in the wrong
order. Move taking of i_mutex further down (luckily it's needed only
for updating inode flags) below where dqio_mutex is taken.
Tested-by: Valdis Kletnieks <valdis.kletnieks@vt.edu>
Signed-off-by: Jan Kara <jack@suse.cz>
|
|
blocks
VAT inode is located in the last block recorded block of the medium. When the
drive errorneously reports number of recorded blocks, we failed to load the VAT
inode and thus mount the medium. This patch makes kernel try to read VAT inode
from the last block of the device if it is different from the last recorded
block.
Signed-off-by: Jan Kara <jack@suse.cz>
|
|
The semaphore used by the async caching threads can prevent a
transaction commit, which can make the FS appear to stall. This
releases the semaphore more often when a transaction commit is
in progress.
Signed-off-by: Chris Mason <chris.mason@oracle.com>
|
|
The async block group caching code uses the commit_root pointer
to get a stable version of the extent allocation tree for scanning.
This copy of the tree root isn't going to change and it significantly
reduces the complexity of the scanning code.
During a commit, we have a loop where we update the extent allocation
tree root. We need to loop because updating the root pointer in
the tree of tree roots may allocate blocks which may change the
extent allocation tree.
Right now the commit_root pointer is changed inside this loop. It
is more correct to change the commit_root pointer only after all the
looping is done.
Signed-off-by: Yan Zheng <zheng.yan@oracle.com>
Signed-off-by: Chris Mason <chris.mason@oracle.com>
|
|
When a file is deleted from a gfs2 filesystem on one node, a dcache
entry for it may still exist on other nodes in the cluster. If this
happens, gfs2 will be unable to free this file on disk. Because of this,
it's possible to have a gfs2 filesystem with no files on it and no free
space. With this patch, when a node receives a callback notifying it
that the file is being deleted on another node, it schedules a new
workqueue thread to remove the file's dcache entry.
Signed-off-by: Benjamin Marzinski <bmarzins@redhat.com>
Signed-off-by: Steven Whitehouse <swhiteho@redhat.com>
|
|
Since both linked and unlinked inodes are counted by rgd->rd_dinodes, It
makes no sense to count them with the used data blocks (first check that
I changed), it makes sense to count them with the linked inodes (second
check), and it makes no sense to care if there are more unlinked inodes
than linked ones. This fixes these errors.
Signed-off-by: Benjamin Marzinski <bmarzins@redhat.com>
Signed-off-by: Steven Whitehouse <swhiteho@redhat.com>
|
